This patch converts the amp access functions to the regmap helpers.
The amp values were formerly cached in the own hash table. Now it's
dropped by the regmap's cache.
The only tricky conversion is snd_hda_codec_amp_init(). This function
shouldn't do anything if the amp was already initialized. For
achieving this behavior, a value is read once at first temporarily in
the cache-only mode. Only if it returns an error, i.e. the item
still doesn't exist in the cache, it proceeds to the update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes we need the uncached reads, e.g. for refreshing the tree.
This patch provides the helper function for that and uses it for
refreshing widgets, reading subtrees and the whole proc reads.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now let's take the basic tracepoints back to the HD-audio driver.
The three bus tracepoints, hda_send_cmd, hda_get_response and
hda_unsol_event are revived but in a slightly different form.
Since we don't assign the card number there, print the bus device name
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance. This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly. It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an overriding exec_verb op to struct hdac_device so that the call
via snd_hdac_exec_verb() can switch to a different route depending on
the setup. The codec driver sets this field so that it can handle the
errors or applying quirks appropriately. Furthermore, this mechanism
will be used for smooth transition for the regmap support in later
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the sysfs files assigned to the codec device on the
bus which were formerly identical with hwdep sysfs files. Now it
shows only a few core parameter, vendor_id, subsystem_id, revision_id,
afg, mfg, vendor_name and chip_name.
In addition, now a widget tree is added to the bus device sysfs
directory for showing the widget topology and attributes. It's just a
flat tree consisting of subdirectories named as the widget NID
including various attributes like widget capability bits. The AFG
(usually NID 0x01) is always found there, and it contains always
amp_in_caps, amp_out_caps and power_caps files. Each of these
attributes show a single value. The rest are the widget nodes
belonging to that AFG. Note that the child node might not start from
0x02 but from another value like 0x0a.
Each child node may contain caps, pin_caps, amp_in_caps, amp_out_caps,
power_caps and connections files. The caps (representing the widget
capability bits) always contain a value. The rest may contain
value(s) if the attribute exists on the node. Only connections file
show multiple values while other attributes have zero or one single
value.
An example of ls -R output is like below:
% ls -R /sys/bus/hdaudio/devices/hdaudioC0D0/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/:
01/ 04/ 07/ 0a/ 0d/ 10/ 13/ 16/ 19/ 1c/ 1f/ 22/
02/ 05/ 08/ 0b/ 0e/ 11/ 14/ 17/ 1a/ 1d/ 20/ 23/
03/ 06/ 09/ 0c/ 0f/ 12/ 15/ 18/ 1b/ 1e/ 21/
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/01:
amp_in_caps amp_out_caps power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/02:
amp_in_caps amp_out_caps caps connections pin_caps pin_cfg
power_caps
/sys/bus/hdaudio/devices/hdaudioC0D0/widgets/03:
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David suggested that the name "power_mgmt" is too ambiguous. Rename
the flag with a bit clearer one "power_save_node".
Also, add the corresponding description to HD-Audio.txt, too.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some pins are used for controlling the LED with the VREF value.
This patch changes the power behavior of such pins to be constantly
up. A new state, pin_fixed, is introduced to nid_path to indicate
that the path contains the fixed pin. This improves also the
readability a bit for other static routes, too.
Then a helper function snd_hda_gen_fix_pin_power() is called from the
codec driver for such fixed pins, and it will create fake paths
containing only these pins with pin_fixed=1 flag.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the widget PM may turn off the pins, this might lead to the silent
output for beep when no explicit paths are given. This patch adds
fake output paths for the beep widget so that the output pins are
dynamically powered upon beep on/off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA codecs used to have the own power controls but they were disabled
at transition to the generic parser due to the coding assuming the
fixed routes. Now we get the proper support of equivalently fine
power management in the generic parser, and the old kludges can be
replaced with it. This results in the reduction of lots of dead
codes.
The advanced PM feature is disabled as default like before for keeping
the compatible behavior. It's enabled via "Dynamic Power-Control"
mixer element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the finer power state control of each widget
depending on the jack plug state and streaming state in addition to
the existing power_down_unused power optimization. The new feature is
enabled only when codec->power_mgmt flag is set.
Two new flags, pin_enabled and stream_enabled, are introduced in
nid_path struct for marking the two individual power states: the pin
plug/unplug and DAC/ADC stream, respectively. They can be set
statically in case they are static routes (e.g. some mixer paths),
too.
The power up and down events for each pin are triggered via the
standard hda_jack table. The call order is hard-coded, relying on the
current implementation of jack event chain (a la FILO/stack order).
One point to be dealt carefully is that DAC/ADC cannot be powered
on/off while streaming. They are pinned as long as the stream is
running. For controlling the power of DAC/ADC, a new patch_ops is
added. The generic parser provides the default callback for that.
As of this patch, only IDT/Sigmatel codec driver enables the flag.
The support on other codecs will follow.
An assumption we made in this code is that the widget state (e.g. amp,
pinctl, connections) remains after the widget power transition (not
about FG power transition). This is true for IDT codecs, at least.
But if the widget state is lost at widget power transition, we'd need
to implement additional code to sync the cached amp/verbs for the
specific NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add sampling rate control for ADC/DAC for ESI W192M.
Allow to switch between 48K/96K/192K sampling rate.
All DAC need to be mute when changing samplerate.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add text Line in/Mic for selecting input gain state in mixer for ESI W192M.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add TLV support to control volume using dB scale for input and ouput on ESI W192M.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable midi i/o port of envy24 chip as their are available on ESI W192M soundcard.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update eeprom structure to C99 standard to be compliant with change in alsa.
It's just a notation change, no configuration change.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct copy/paste name from prodigy driver, no behaviour change, only name.
Signed-off-by: Clément Guedez <klem.dev@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does two things:
- code refactoring with a local helper function,
- allow codec drivers to provide the specific PCM stream info pointers
only for overriding the non-NULL entries, instead of copying the
whole.
This simplifies the codec driver side (currently the only user is
alc269's 44kHz fixed rate).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCA+HAAoJECTWi3JdVIfQ6oQIAIOFlrPzKpI3C7MqrK6F+ySC
g/JOf8XZKbStl+RdSu/RI6gL1Nc4VD7EHv5vEM2Br6KtUHQMoQYpsSiPvn1BFJBX
EkwY3eoDiIyPqQG7cGmdIF/8NXiZgJYh13coamrkdAhBFMXfmqlbrBHo71Z6o1ic
cg4rng3AmjyJ1NfUDsMW/KTX0F8AUTw7yYs+B4pyjfRBFVmhmzubXGXNjiW+/Tz4
zjk9c3Qm7ZxC66dbvg5lpIakwbRtX26p7Fn+pWOewL4y81y9qruSvV6IgDZ1RO95
DRtLsU7qyIK3G9zCw61xJNiL2QAfgOfYYgi7R6XrlS3nttIFT30oELw5ObwjSM0=
=iSeG
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
The commit [ef403edb75: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
driver fixes for new regressions since v3.19. Second are fixes to the
common clock divider type caused by recent changes to how we round clock
rates. This affects many clock drivers that use this common code.
Finally there are fixes for drivers that improperly compared struct clk
pointers (drivers must not deref these pointers). While some of these
drivers have done this for a long time, this did not cause a problem
until we started generating unique struct clk pointers for every
consumer. A new function, clk_is_match was introduced to get these
drivers working again and they are fixed up to no longer deref the
pointers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVBewEAAoJEKI6nJvDJaTUR2gP/2frIXCm/krwkDyofIGxxQ+F
RwIXFTn9GG9QEUwKLUcxRUegHbWbZMXYp6W19hUcUdYz3pD+uEJSuH0NI8kW1Ohy
32P5/ALuoTq7OVzBBz/9di9jBDdIM1wusLZGJfOWk9DXBLOS3VHuhN55D47dqWS/
GsszeEpp8r1WBKFVmAkuQ5Jc0CqgS5GxvMOndXXVN3kDMhCT+9pBiqtUT0V3YV/J
d5GCvfPlO/Xmjnpjf99MPButkfiW/o6YXt3H0QY6hhskS1Av8alyfabVctk8lqOW
py8SQFY7MdRLZ84Zk87sqKCKUc/vHkTBT9vKWYm65l3yJ5OEFv60NaFMYY61HVlJ
n6qWU6SbFZvkPnQTJn6Ii/v7BQ92bXjYpLNcBK8UY35jIjmHsPS/YXCbkmArtn1N
/yAB4TIfH8uX93smFb3XEmZLSiKFuZAhU8YbjDzYgsGuQ9EwN3aNP9c5mzC7Soou
tYnDqVic0i993qQTD2Db5dplGwxelCRJpazO2kK6NW/EJzE8XJaM6XVy1xIBKiDX
bbWPdp53/eWV7gbUEZ8zzcS06G/DLw5/N45XyaWIx+2ThDjhOAlVHTAFDY+Oa743
42Dkwtr5GZ6yORyXY1wI5HttUGU0gnPN0kM84GQG8O/GbzGureZSW1e6G7tJJljn
JXhROl0w4aIPwUUxry7R
=nc5C
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit [2225e79b9b: 'ALSA: core: reduce stack usage related
to snd_ctl_new()'], the id field of the newly added kctl is untouched,
thus all attribute like name string remain empty. The fix is just to
add the forgotten memcpy of the id field.
Fixes: 2225e79b9b ('ALSA: core: reduce stack usage related to snd_ctl_new()')
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the
built-in mic records only the right channel. Apply the same
workaround as MBP8,1 to spread the mono channel via a Cirrus codec
vendor-specific COEF setup.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CS420x codecs seem to deal only the single amps of ADC nodes even
though the nodes receive multiple inputs. This leads to the
inconsistent amp value after S3/S4 resume, for example.
The fix is just to set codec->single_adc_amp flag. Then the driver
handles these ADC amps as if single connections.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device complies to the UAC1 standard but hides that fact with
proprietary descriptors. The autodetect quirk for Roland devices
catches the audio interface but misses the MIDI part, so a specific
quirk is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Rafa Lafuente <rafalafuente@gmail.com>
Tested-by: Raphaël Doursenaud <raphael@doursenaud.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There was no check about the id string of user control elements, so we
accepted even a control element with an empty string, which is
obviously bogus. This patch adds more sanity checks of id strings.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the
built-in mic NID 0x17 instead of NID 0x1d, and it results in the
non-working mic. This patch just remaps the pin correctly via fixup.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the sequencer driver is built in kernel, it may panic at boot
because of the uninitialized snd_seq_bus_type. Initialize it properly
via subsys_initcall() instead of module_init() to assure that the bus
is registered beforehand.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 7c37ae5c62 ('ALSA: seq: Rewrite sequencer device binding with standard bus')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
