When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.
In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.
Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.
v2:
- Rebase; the SKL atomic WM patches that just landed changed the WM
structure fields in intel_crtc_state slightly. (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit e3d5457c7c)
[Jani: rebase on drm-next while cherry-picking]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If planes are added to the state after the call to
drm_atomic_helper_check_planes planes_changed may not be set
and we will not unpin the old framebuffer. This results in a
pin leak long after the framebuffer is destroyed, so to find
this add some checks when it happens.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-21-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
intel_unpin_work may not take the list lock because it requires the connector_mutex.
To prevent taking locks we add an array of old and new state. The old state to free,
the new state to commit and verify.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-18-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Create a work structure that will be used for all changes. This will
be used later on in the atomic commit function.
Changes since v1:
- Free old_crtc_state from unpin_work_fn properly.
Changes since v2:
- Add hunk for calling hw state verifier.
- Add missing support for color spaces.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-12-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
With intel_pipe_update begin/end we ensure that the mmio updates
don't run during vblank interrupt, using the hw counter we can
be sure that when current vblank count != vblank count at the time
of pipe_update_end the mmio update is complete.
This allows us to use mmio updates on all platforms, using the
update_plane call.
With Chris Wilson's patch to skip waiting for vblanks for
legacy_cursor_update this potentially leaves a small race
condition, in which update_plane can be called with a freed
crtc_state. Because of this commit acf4e84d61
("drm/i915: Avoid stalling on pending flips for legacy cursor updates")
is temporarily reverted.
Changes since v1:
- Split out the flip_work rename.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Rename intel_unpin_work to intel_flip_work and use it for mmio flips
and unpinning. Use flip_queued_req to hold the wait request in the
mmio case, and the vblank counter from intel_crtc_get_vblank_counter.
MMIO flips get their own path through intel_finish_page_flip_mmio,
handled on vblank. CS page flips go through *_cs.
Changes since v1:
- Clean up destinction between MMIO and CS flips.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-7-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Instead of calling prepare_flip right before calling finish_page_flip
do everything from prepare_page_flip in finish_page_flip.
Putting prepare and finish page_flip in a single step removes the need
for INTEL_FLIP_COMPLETE, so it can be removed. This simplifies the code
slightly.
Changes since v1:
- Invert if case to simplify code.
- Add missing barrier.
- Reword commit message.
Changes since v2:
- intel_page_flip_plane is removed.
- work->pending is turned into a bool.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Both intel_unpin_work.pending and intel_unpin_work.enable_stall_check
were used to see if work should be enabled. By only using pending
some special cases are gone, and access to unpin_work can be simplified.
A flip could previously be queued before
stallcheck was active. With the addition of the pending member
enable_stall_check became obsolete and can thus be removed.
Use this to only access work members untilintel_mark_page_flip_active
is called, or intel_queue_mmio_flip is used. This will prevent
use-after-free, and makes it easier to verify accesses.
Changes since v1:
- Reword commit message.
- Do not access unpin_work after intel_mark_page_flip_active.
- Add the right memory barriers.
Changes since v2:
- atomic_read() needs a full smp_rmb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
- Unconditionally add plane states. Core helpers would have done this
in drm_atomic_helper_check_modeset, doing it once more won't cause
harm and is less fragile.
- Simplify the continue logic when disabling a pipe.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462779085-2458-1-git-send-email-daniel.vetter@ffwll.ch
Backmerge request by Jani to get at
commit 249c4f538b
Author: Deepak M <m.deepak@intel.com>
Date: Wed Mar 30 17:03:39 2016 +0300
drm: Add new DCS commands in the enum list
Some simple conflicts in intel_dp.c.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's unused, and really this helper should only look at the state
structure and nothing else.
v2: Rebase on top of rockchip changes
v3: Drop unrelated hunk, spotted by Laurent.
v4: Rebase onto mtk driver merge.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462804451-15318-1-git-send-email-daniel.vetter@ffwll.ch
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.
In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.
Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.
v2:
- Rebase; the SKL atomic WM patches that just landed changed the WM
structure fields in intel_crtc_state slightly. (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com
BXT could change the CD2X divider synchronized with a single pipe.
So assuming the DE PLL frequency doesn't need to be changed, we could
change cdclk without shutting off the pipe (when only a single pipe is
enabled). In the meantime let's configure CDCLK_CTL for non-double
buffered CD2X update, although it shouldn't really matter as long as
the selected pipe is disabled when reprogramming the divider.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Make thins a bit easier to read by extracting the SKL DPLL0
disable into separate functions. We already have the enable
counterpart. Down the line this will also help make the cdclk
programming on SKL, BXT, and following platforms look rather
consistent.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Both SKL and BXT need to fill in the "decimal" cdclk frequency into
the CDCLK_CTL register. SKL uses a small helper to do the kHz->"decimal"
conversion, whereas BXT has it open-coded. Use the helper on BXT too.
While at it, change it to round to closest rather than down. It doesn't
actually matter with the frequencies we have to deal with, but it seems
like the right thing to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
BXT uses the "pch" panel fitter configuration, so we can use
ilk_max_pixel_rate() instead of intel_mode_max_pixclk() to compute the
pipe pixel rate. ilk_max_pixel_rate() will account for the pipe
scaler downscaling factor whereas intel_mode_max_pixclk() will not.
I'm pretty sure the same limitation is there on GMCH platforms, but
no one just bothered to implement the downscaling adjustment for them.
Probably should just unify the panel fitter setup more across the
platforms and use the exact same code on all platforms for this.
But in the meantime, let's at least make BXT a bit more correct.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
commit 565602d750 ("drm/i915: Do not acquire crtc state to check clock during modeset, v4.")
removed the possibility that intel_mode_max_pixclk() or
ilk_max_pixel_rate() might return an error, so let's get rid of the
error checks in the callers as well.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We calculate the watermark config into intel_atomic_state and then save
it into dev_priv, but never actually use it from there. This is
left-over from some early ILK-style watermark programming designs that
got changed over time.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-18-git-send-email-matthew.d.roper@intel.com
Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).
Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction. The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state. That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time. However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved). With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).
We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.
v2:
- Bail out of skl_write_wm_values() if the CRTC isn't active. Now that
we set dirty_pipes to ~0 if the active pipes change (because
we need to deal with DDB changes), we can now wind up here for
disabled pipes, whereas we couldn't before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com
Once we move watermark calculation to the atomic check phase, we'll want
to start rejecting display configurations that exceed out watermark
limits. At the moment we just assume that there's always a valid set of
watermarks, even though this may not actually be true. Let's prepare by
passing return codes up through the call stack in preparation.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-15-git-send-email-matthew.d.roper@intel.com
Now that we're properly pre-allocating the DDB during the atomic check
phase and we trust that the allocation is appropriate, let's actually
use the allocation computed and not duplicate that work during the
commit phase.
v2:
- Significant rebasing now that we can use cached data rates and
minimum block allocations to avoid grabbing additional plane states.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-11-git-send-email-matthew.d.roper@intel.com
Calculate the DDB blocks needed to satisfy the current atomic
transaction at atomic check time. This is a prerequisite to calculating
SKL watermarks during the 'check' phase and rejecting any configurations
that we can't find valid watermarks for.
Due to the nature of DDB allocation, it's possible for the addition of a
new CRTC to make the watermark configuration already in use on another,
unchanged CRTC become invalid. A change in which CRTC's are active
triggers a recompute of the entire DDB, which unfortunately means we
need to disallow any other atomic commits from racing with such an
update. If the active CRTC's change, we need to grab the lock on all
CRTC's and run all CRTC's through their 'check' handler to recompute and
re-check their per-CRTC DDB allocations.
Note that with this patch we only compute the DDB allocation but we
don't actually use the computed values during watermark programming yet.
For ease of review/testing/bisecting, we still recompute the DDB at
watermark programming time and just WARN() if it doesn't match the
precomputed values. A future patch will switch over to using the
precomputed values once we're sure they're being properly computed.
Another clarifying note: DDB allocation itself shouldn't ever fail with
the algorithm we use today (i.e., we have enough DDB blocks on BXT to
support the minimum needs of the worst-case scenario of every pipe/plane
enabled at full size). However the watermarks calculations based on the
DDB may fail and we'll be moving those to the atomic check as well in
future patches.
v2:
- Skip DDB calculations in the rare case where our transaction doesn't
actually touch any CRTC's at all. Assuming at least one CRTC state
is present in our transaction, then it means we can't race with any
transactions that would update dev_priv->active_crtcs (which requires
_all_ CRTC locks).
v3:
- Also calculate DDB during initial hw readout, to prevent using
incorrect bios values. (Maarten)
v4:
- Use new distrust_bios_wm flag instead of skip_initial_wm (which was
never actually set).
- Set intel_state->active_pipe_changes instead of just realloc_pipes
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude Paul <cpaul@redhat.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-10-git-send-email-matthew.d.roper@intel.com
SKL-style platforms can't fully trust the watermark/DDB settings
programmed by the BIOS and need to do extra sanitization on their first
atomic update. Add a flag to dev_priv that is set during hardware
readout and cleared at the end of the first commit.
Note that for the somewhat common case where everything is turned off
when the driver starts up, we don't need to bother with a recompute...we
know exactly what the DDB should be (all zero's) so just setup the DDB
directly in that case.
v2:
- Move clearing of distrust_bios_wm up below the swap_state call since
it's a more natural / self-explanatory location. (Maarten)
- Use dev_priv->active_crtcs to test whether any CRTC's are turned on
during HW WM readout rather than trying to count the active CRTC's
again ourselves. (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-9-git-send-email-matthew.d.roper@intel.com
For the purposes of DDB re-allocation we need to know whether a
transaction changes the list of CRTC's that are active. While
state->modeset could be used for this purpose, that would be slightly
too aggressive since it would lead us to re-allocate the DDB when a
CRTC's mode changes, but not its final active state.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-7-git-send-email-matthew.d.roper@intel.com
Code checkers may complain about the explicit casts between different
enum types, so add comments for known-valid cases to help future
triaging of such complaints.
v2:
- Make the comments more logical (Ville).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463059132-1720-3-git-send-email-imre.deak@intel.com
The coding style documentation says the following about typedefs:
"In general, a pointer, or a struct that has elements that can
reasonably be directly accessed should _never_ be a typedef."
intel_limit_t falls in that category, so just use "struct intel_limit"
instead.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462353119-9738-3-git-send-email-ander.conselvan.de.oliveira@intel.com
Another day, another long overdue conversion. Not much to update inside
intel_overlay.c, but still
text data bss dec hex filename
6309547 3578778 696320 10584645 a18245 vmlinux
6309291 3578778 696320 10584389 a18145 vmlinux
a couple of hundred bytes of pointer misdirection.
Whilst here, rename the ioctl entry points to include the _ioctl suffix
so that the user entry points are clear (following the idiom).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1463053403-25086-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This way optimization from a previous patch works even better.
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pass drm_i915_private to the uncore init/fini routines and their
subservients as it is their native type.
text data bss dec hex filename
6309978 3578778 696320 10585076 a183f4 vmlinux
6309530 3578778 696320 10584628 a18234 vmlinux
a modest 400 bytes of saving, but 60 lines of code deleted!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462885804-26750-1-git-send-email-chris@chris-wilson.co.uk
When the crtc is enabled but !active, we should still compute the
watermarks as if the planes were visible. That would make it more
likely that the we can later transition to active without errors.
Add a FIXME to remind people that we're doing the wrong thing now.
We should perhaps just move the wm computation for each individual plane
into the .check_plane hook, and later we'd just combine the results from
all active planes.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461940278-17122-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
text data bss dec hex filename
6309351 3578714 696320 10584385 a18141 vmlinux
6308391 3578714 696320 10583425 a17d81 vmlinux
Almost 1KiB of code reduction.
v2: More s/INTEL_INFO()->gen/INTEL_GEN()/ and IS_GENx() conversions
text data bss dec hex filename
6304579 3578778 696320 10579677 a16edd vmlinux
6303427 3578778 696320 10578525 a16a5d vmlinux
Now over 1KiB!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462545621-30125-3-git-send-email-chris@chris-wilson.co.uk
I have noticed some of our interrupt handlers use both dev and
dev_priv while they could get away with only dev_priv in the
huge majority of cases.
Tidying that up had a cascading effect on changing functions
prototypes, so relatively big churn factor, but I think it is
for the better.
For example even where changes cascade out of i915_irq.c, for
functions prefixed with intel_, genX_ or <plat>_, it makes more
sense to take dev_priv directly anyway.
This allows us to eliminate local variables and intermixed usage
of dev and dev_priv where only one is good enough.
End result is shrinkage of both source and the resulting binary.
i915.ko:
- .text 000b0899
+ .text 000b0619
Or if we look at the Gen8 display irq chain:
-00000000000006ad t gen8_irq_handler
+0000000000000663 t gen8_irq_handler
-0000000000000028 T intel_opregion_asle_intr
+0000000000000024 T intel_opregion_asle_intr
-000000000000008c t ilk_hpd_irq_handler
+000000000000007f t ilk_hpd_irq_handler
-0000000000000116 T intel_check_page_flip
+0000000000000112 T intel_check_page_flip
-000000000000011a T intel_prepare_page_flip
+0000000000000119 T intel_prepare_page_flip
-0000000000000014 T intel_finish_page_flip_plane
+0000000000000013 T intel_finish_page_flip_plane
-0000000000000053 t hsw_pipe_crc_irq_handler
+000000000000004c t hsw_pipe_crc_irq_handler
-000000000000022e t cpt_irq_handler
+0000000000000213 t cpt_irq_handler
So small shrinkage but it is all fast paths so doesn't harm.
Situation is similar in other interrupt handlers as well.
v2: Tidy intel_queue_rps_boost_for_request as well. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
This was forgotten when adding the the refcounting to
drm_connector_state.
v2: Don't forget to unreference existing connectors. This isn't
relevant on driver load, but this code also runs on resume, and there
we already have an atomic state. Spotted by Chris Wilson.
Cc: Gabriel Feceoru <gabriel.feceoru@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Marius Vlad <marius.c.vlad@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Fixes: d2307dea14 ("drm/atomic: use connector references (v3)")
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462541943-19620-1-git-send-email-daniel.vetter@ffwll.ch
Ofc I promise just a few leftovers for drm-misc and somehow it's the
biggest pull. But really mostly trivial stuff:
- MAINTAINERS updates from Emil
- rename async to nonblock in atomic_commit to avoid the confusion between
nonblocking ioctl and async flip (= not vblank synced), from Maarten.
Needs to be regened with newer drivers, but probably only after -rc1 to
catch them all.
- actually lockless gem_object_free, plus acked driver conversion patches.
All the trickier prep stuff already is in drm-next.
- Noralf's nice work for generic defio support in our fbdev emulation.
Keeps the udl hack, and qxl is tested by Gerd.
* tag 'topic/drm-misc-2016-05-04' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm: Fixup locking WARN_ON mistake around gem_object_free_unlocked
drm/etnaviv: Use lockless gem BO free callback
drm/imx: Use lockless gem BO free callback
drm/radeon: Use lockless gem BO free callback
drm/amdgpu: Use lockless gem BO free callback
drm/gem: support BO freeing without dev->struct_mutex
MAINTAINERS: Add myself for the new VC4 (RPi GPU) graphics driver.
MAINTAINERS: Add a bunch of legacy (UMS) DRM drivers
MAINTAINERS: Add a few DRM drivers by Dave Airlie
MAINTAINERS: List the correct git repo for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Renesas DRM drivers
MAINTAINERS: Update the files list for the Armada DRM driver
MAINTAINERS: Update the files list for the Rockchip DRM driver
MAINTAINERS: Update the files list for the Exynos DRM driver
MAINTAINERS: Add maintainer entry for the VMWGFX DRM driver
MAINTAINERS: Add maintainer entry for the MSM DRM driver
MAINTAINERS: Add maintainer entry for the Nouveau DRM driver
MAINTAINERS: Update the files list for the Etnaviv DRM driver
MAINTAINERS: Remove unneded wildcard for the i915 DRM driver
drm/atomic: Add WARN_ON when state->acquire_ctx is not set.
...
The LVDS border enable is independent from the panel fitter. Move the
readout of the "border bits" from i9xx_get_pfit_config() to
intel_lvds_get_config(), where it will be read if LVDS is enabled even
if the panel fitter is not.
This fixes the state checker warning:
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in
gmch_pfit.lvds_border_bits (expected 0x00008000, found 0x00000000)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87632
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461933243-2140-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit a0cbe6a3f1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: stable@vger.kernel.org
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit 7f1052a8fa)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The LVDS border enable is independent from the panel fitter. Move the
readout of the "border bits" from i9xx_get_pfit_config() to
intel_lvds_get_config(), where it will be read if LVDS is enabled even
if the panel fitter is not.
This fixes the state checker warning:
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in
gmch_pfit.lvds_border_bits (expected 0x00008000, found 0x00000000)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87632
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461933243-2140-1-git-send-email-jani.nikula@intel.com
The comment about GMBUSFREQ is confused. The spec actually explains
the 4MHz thing perfectly by noting that the 4MHz divider values is
actually just bits [9:2] not [9:0], hence the divide by 1000 correct.
Replace the confused note with a quote from the spec, and eliminate
the duplicated comment that snuck in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: stable@vger.kernel.org
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
If we move the release of the GEM request (i.e. decoupling it from the
various lists used for client and context tracking) after it is complete
(either by the GPU retiring the request, or by the caller cancelling the
request), we can remove the requirement that the final unreference of
the GEM request need to be under the struct_mutex.
The careful reader may notice that one or two impossible NULL pointer
tests are dropped for readability. These pointers cannot be NULL since
they are assigned during request construction and never unset.
v2,v3: Rebalance execlists by moving the context unpinning.
v4: Rebase onto -nightly
v5: Avoid trying to rebalance execlist/GuC context pinning, leave that
to the next step
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-21-git-send-email-chris@chris-wilson.co.uk
Propagate the real error from drm_gem_object_init(). Note this also
fixes some confusion in the error return from i915_gem_alloc_object...
v2:
(Matthew Auld)
- updated new users of gem_alloc_object from latest drm-nightly
- replaced occurrences of IS_ERR_OR_NULL() with IS_ERR()
v3:
(Joonas Lahtinen)
- fix double "From:" in commit message
- add goto teardown path
v4:
(Matthew Auld)
- rebase with i915_gem_alloc_object name change
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461587533-8841-1-git-send-email-matthew.auld@intel.com
[Joonas: Removed spurious " = NULL" from _init() function]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.
Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.
But since the register is there, let's configure it in accordance with
the spec.
Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874ed ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit acf4e84d61)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Because having both i915_gem_object_alloc() and i915_gem_alloc_object()
(with different return conventions) is just too confusing!
(i915_gem_object_alloc() is the low-level memory allocator, and remains
unchanged, whereas i915_gem_alloc_object() is a constructor that ALSO
initialises the newly-allocated object.)
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461348872-4702-1-git-send-email-david.s.gordon@intel.com
When a vblank wait times out in intel_atomic_wait_for_vblanks() we just
get a cryptic 'WARN_ON(!ret)' backtrace in dmesg. Repace it with
something that tells you what actually happened.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460978973-24945-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874ed ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Compute the DSI PLL parameters during .compute_config() rather than
.pre_pll_enable() so that we can fail gracefully if we can't find
suitable parameters.
In order to do that we need to store the DSI PLL parameters in
pipe_config.
v2: Handle BXT too
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-3-git-send-email-ville.syrjala@linux.intel.com
Tested-by: Jani Nikula <jani.nikula@intel.com>
Set up DPLL and DPLL_MD even when driving DSI output on VLV/CHV. While
the DPLL isn't used to provide the clock we still need the refclock, and
it appears that the pixel repeat factor also has an effect on DSI
output. So set up eveyrhing in DPLL and DPLL_MD as we would do for
DP/HDMI/VGA, but don't actually enable the DPLL or configure the
dividers via DPIO.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459780030-15781-1-git-send-email-imre.deak@intel.com
When determining whether CDCLK is enabled by BIOS and so we should skip
reprogramming it, we didn't check the related DBUF power request and
state. In theory BIOS could enable one without the other so check for
this case and reprogram things if something is amiss.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-13-git-send-email-imre.deak@intel.com
Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.
For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-12-git-send-email-imre.deak@intel.com
For internal APIs passing dev_priv is preferred to reduce indirections,
so convert over a few DDI PHY, CDCLK helpers.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-10-git-send-email-imre.deak@intel.com
Conceptually, each request is a record of a hardware transaction - we
build up a list of pending commands and then either commit them to
hardware, or cancel them. However, whilst building up the list of
pending commands, we may modify state outside of the request and make
references to the pending request. If we do so and then cancel that
request, external objects then point to the deleted request leading to
both graphical and memory corruption.
The easiest example is to consider object/VMA tracking. When we mark an
object as active in a request, we store a pointer to this, the most
recent request, in the object. Then we want to free that object, we wait
for the most recent request to be idle before proceeding (otherwise the
hardware will write to pages now owned by the system, or we will attempt
to read from those pages before the hardware is finished writing). If
the request was cancelled instead, that wait completes immediately. As a
result, all requests must be committed and not cancelled if the external
state is unknown.
All that remains of i915_gem_request_cancel() users are just a couple of
extremely unlikely allocation failures, so remove the API entirely.
A consequence of committing all incomplete requests is that we generate
excess breadcrumbs and fill the ring much more often with dummy work. We
have completely undone the outstanding_last_seqno optimisation.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93907
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-16-git-send-email-chris@chris-wilson.co.uk
Reporting -EIO from i915_wait_request() has proven very troublematic
over the years, with numerous hard-to-reproduce bugs cropping up in the
corner case of where a reset occurs and the code wasn't expecting such
an error.
If the we reset the GPU or have detected a hang and wish to reset the
GPU, the request is forcibly complete and the wait broken. Currently, we
report either -EAGAIN or -EIO in order for the caller to retreat and
restart the wait (if appropriate) after dropping and then reacquiring
the struct_mutex (essential to allow the GPU reset to proceed). However,
if we take the view that the request is complete (no further work will
be done on it by the GPU because it is dead and soon to be reset), then
we can proceed with the task at hand and then drop the struct_mutex
allowing the reset to occur. This transfers the burden of checking
whether it is safe to proceed to the caller, which in all but one
instance it is safe - completely eliminating the source of all spurious
-EIO.
Of note, we only have two API entry points where we expect that
userspace can observe an EIO. First is when submitting an execbuf, if
the GPU is terminally wedged, then the operation cannot succeed and an
-EIO is reported. Secondly, existing userspace uses the throttle ioctl
to detect an already wedged GPU before starting using HW acceleration
(or to confirm that the GPU is wedged after an error condition). So if
the GPU is wedged when the user calls throttle, also report -EIO.
v2: Split more carefully the change to i915_wait_request() and assorted
ABI from the reset handling.
v3: Add a couple of WARN_ON(EIO) to the interruptible modesetting code
so that we don't start to leak EIO there in future (and break our hang
resistant modesetting).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-9-git-send-email-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-1-git-send-email-chris@chris-wilson.co.uk
Now that the reset_counter is stored on the request, we can rearrange
the code to handle reading the counter versus waiting during the atomic
modesetting for readibility (by deleting the hairiest of codes).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-8-git-send-email-chris@chris-wilson.co.uk
As the request is only valid during the same global reset epoch, we can
record the current reset_counter when constructing the request and reuse
it when waiting upon that request in future. This removes a very hairy
atomic check serialised by the struct_mutex at the time of waiting and
allows us to transfer those waits to a central dispatcher for all
waiters and all requests.
PS: With per-engine resets, we obviously cannot assume a global reset
epoch for the requests - a per-engine epoch makes the most sense. The
challenge then is how to handle checking in the waiter for when to break
the wait, as the fine-grained reset may also want to requeue the
request (i.e. the assumption that just because the epoch changes the
request is completed may be broken - or we just avoid breaking that
assumption with the fine-grained resets).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-7-git-send-email-chris@chris-wilson.co.uk
If we, when we store the reset_counter for the operation, we ensure that
it is not in a wedged or in the middle of a reset, we can then assert that
if any reset occurs the reset_counter must change. Later we can just
compare the operation's reset epoch against the current counter to see
if we need to abort the operation (to handle the hang).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-5-git-send-email-chris@chris-wilson.co.uk
This is principally a little bit of syntatic sugar to hide the
atomic_read()s throughout the code to retrieve the current reset_counter.
It also provides the other utility functions to check the reset state on the
already read reset_counter, so that (in later patches) we can read it once
and do multiple tests rather than risk the value changing between tests.
v2: Be more strict on converting existing i915_reset_in_progress() over to
the more verbose i915_reset_in_progress_or_wedged().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-4-git-send-email-chris@chris-wilson.co.uk
Check whether the DPLL is even enabled before readoing out the dividers
and trying to derive port_clock on CHV. We already did this on VLV.
Also remove the comment "MIPI" comment from the VLV code since we call
this function whenever the pipe is enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Take a bigger hammer to the underrun suppression on ILK. Instead of
trying to suppress them at specific points in the modeset sequence just
silence them across the entire sequence. This gets rid of some underruns
at least on my ILK. Note that this changes SNB and IVB to follow the
same approach just to keep the code less convoluted. The difference is
that on those platforms we won't suppress CPU underruns for port A since
it doesn't seem to be necessary.
My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is
as effective on other PCH port types. Perhaps we still need some of
Daniel's extra vblank waits [2]?
I've still been able to trigger an underrun on the other pipe, but
fixing that perhaps needs the LP1+ disable trick I implemented here [1]
which never got merged.
A few details which hamper stress testing on my ILK are that sometimes
the PCH transcoder gets messed up and refuses to shut down, and sometimes
even the panel power sequencer apparently gets stuck on the always on
position.
[1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html
[2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html
v2: Add a note that we also get underruns when enabling PCH ports
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Check functions are used by atomic to see if the new state will
be allowed. There's also a hw state checker which checks afterwards
that the committed state is correct. Rename it to hw state verifier
to reduce some confusion.
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56FB8785.8020506@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The modeset state verifier no longer has full access to the hardware,
instead it should only verify affected crtc's.
Looking for disabled stuff can be verified immediately after all crtc
disables have completed, while each enabled crtc can be verified right
after being enabled.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: check -> verify]
This will make it easier to keep the crtc checker when atomic
commit is reworked for asynchronous commits. This prevents checking
crtc's that were not part of the state. It's safe to verify disabled
encoders, connectors and dpll's that are not part of the state,
because during modeset connection_mutex is held.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Extend commit message and rename check to verify.]
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
intel_update_max_cdclk() doesn't have a switch case for Broxton, so
dev_priv->max_cdclk_freq gets set to whatever clock frequency we're
currently running at (e.g., 144 MHz) rather than the true maximum. This
causes our max dotclock to also be set too low and in turn leads mode
verification to reject perfectly valid modes while loading EDID firmware
blobs.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459892239-14041-1-git-send-email-matthew.d.roper@intel.com
Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Deal with errors from drm_universal_plane_init() in primary and cursor
plane init paths (sprites were already covered). Also make the code
neater by using goto for error handling.
v2: Rebased due to drm_universal_plane_init() 'name' parameter
v3: Another rebase due to s/""/NULL/
v4: Rebased on drm-nightly (Matthew Auld)
v5: Fix email address (Matthew Auld)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571402-32749-1-git-send-email-matthew.auld@intel.com
Supposedly the power sequencer still locks out the DPLL registers on
CHV, so let's issue a warning if it's still locked when enabling the
DPLL.
Also drop the redundant IS_MOBILE() check for VLV when we check the same
thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DPLL_MD(PIPE_C) is AWOL on CHV. Instead of fixing it someone added
chicken bits to propagate the pixel multiplier from DPLL_MD(PIPE_B)
to either pipe B or C. So do that to make pixel repeat work on pipes
B and C. Pipe A is fine without any tricks.
Fortunately the pixel repeat propagation appears to be a oneshot
operation, so once the value has been written we can clear the
chicken bits. So it is still possible to drive pipe B and C with
different pixel multipliers simultaneosly.
Looks like DPLL_VGA_MODE_DIS must also be set in DPLL(PIPE_B)
for this to work. But since we keep that bit always set in all
DPLLs there's no problem.
This of course means we can't reliably read out the pixel multiplier
for pipes B and C. That would make the state checker unhappy, so I
added shadow copies of those registers in to dev_priv. The other
option would have been to skip pixel multiplier, dpll_md an dotclock
checks entirely on CHV, but that feels like a serious loss of cross
checking, so just pretending that we have working DPLL MD registers
seemed better. Obviously with the shadow copies we can't detect if
the pixel multiplier was properly configured, nor can we take over
its state from the BIOS, but hopefully people won't have displays
that would be limitd to such crappy modes.
There is one strange flicker still remaining. It's visible on
pipe C/HDMID when HDMIB is enabled while driven by pipe B.
It doesn't occur if pipe A drives HDMIB, nor is there any glitch
on pipe B/HDMIB when port C/HDMID starts up. I don't have a board
with HDMIC so not sure if it happens there too. So I'm not sure
if it's somehow tied in with this strange linkage between pipe B
and C. Sadly I was unable to find an enable sequence that would
avoid the glitch, but at least it's not fatal ie. the output
recovers afterwards.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The VLV and CHV DPLL disable and update are almost identical in
how the DPLL/DPLL_MD registers need to be set up. But the code
looks more different than it really is. Try to bring them into
line.
Note that we now leave the refclock always enabled for both
DPLLs in the dual channel PHY. But that's perfectly fine since
it's the same clock, and we anyway already do that when turning
the disp2d power well on.
v2: s/chv_update_pll/chv_compute_dpll/
v3: Add a note that we leave refclocks enabled for both DPLLs (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Refer to the GGTT VM consistently as "ggtt->base" instead of just "ggtt",
"vm" or indirectly through other variables like "dev_priv->ggtt.base"
to avoid confusion with the i915_ggtt object itself and PPGTT VMs.
Refer to the GGTT as "ggtt" instead of indirectly through chaining.
As a bonus gets rid of the long-standing i915_obj_to_ggtt vs.
i915_gem_obj_to_ggtt conflict, due to removal of i915_obj_to_ggtt!
v2:
- Added some more after grepping sources with Chris
v3:
- Refer to GGTT VM through ggtt->base consistently instead of ggtt_vm
(Chris)
v4:
- Convert all dev_priv->ggtt->foo accesses to ggtt->foo.
v5:
- Make patch checker happy
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Without this a vblank may occur between updating color management
and planes, which should be prevented.
intel_color_set_csc was called in update pipe config because the
handover from hardware may not have any csc set, which resulted
in a black screen. Because of this also update color management
during fastset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459350996-4957-4-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Remove comment in response to review feedback.]
And move the comment to the right macro. This was mixed up in
commit cfb23ed622
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Jul 14 12:17:40 2015 +0200
drm/i915: Allow fuzzy matching in pipe_config_compare, v2
v2: Rebase.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459330476-32453-1-git-send-email-daniel.vetter@ffwll.ch
Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.
The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.
Ville also found this dependency specified in BSpec, so I added a
reference to that too.
v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
bxt_dsi_pll_is_enabled()
CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2fc ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com
intel_post_plane_update did an extra vblank wait that's no longer needed when enabling ips.
Changes since v1:
- Add comment explaining why vblank wait is performed. (Paulo)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56F29B28.5070804@linux.intel.com
Split a GEN2 specific version from i9xx_crtc_compute_clock(). With this
there is no need for i9xx_get_refclk() anymore, and the differences
between platforms become more obvious.
v2: Use i8xx as prefix instead of gen2. (Ville and Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458653723-17951-1-git-send-email-ander.conselvan.de.oliveira@intel.com
In order for VLV and CHV to use i9xx_crtc_compute_clocks(), a number
of if ladders is necessary: one for setting the find_dpll() hook, one
for choosing the limits struct, one for choosing the right compute dpll
function and one for initializing the crtc_compute_clock() hook.
By extracting a platform specific implementation for each platform, the
number of if-ladders is reduced to one.
While at it also clean up bxt_find_best_dpll() which depends on some of
the CHV code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-13-git-send-email-ander.conselvan.de.oliveira@intel.com
Merge ironlake_compute_clocks() into ironlake_crtc_compute_clock() so
the clock computation logic is all in one place. The resulting function
is still quite simple. Follow up patches will make the similar code for
GMCH platforms look similar.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-12-git-send-email-ander.conselvan.de.oliveira@intel.com
When calculating clocks, just pass a pointer to crtc_state->dpll
directly to the find_dpll() hook. Back when this was introduced in
commit f47709a950 ("drm/i915: create pipe_config->dpll for clock
state") there was no staged crtc config or atomic crtc state, so it was
possible to overwrite the current configuration on error. That hasn't
been the case for a while now, so finally make it "disappear".
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-10-git-send-email-ander.conselvan.de.oliveira@intel.com
None of the code in ironlake_crtc_compute_clock() is relevant for CPU
eDP. The CPU eDP PLL is turned on and off in ironlake_edp_pll_{on,off}
from the DP code and that doesn't depend on the crtc_state->dpll values,
so just return early in that case.
v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-9-git-send-email-ander.conselvan.de.oliveira@intel.com
The checks were added in commit 5dc5298bb3 ("drm/i915: add proper
CPU/PCH checks to crtc_mode_set functions") in a time when there was
doubts on what PCHs would be supported by HSW. There are similar checks
for PCH type in intel_detect_pch() and the function pointers are
initialized based on platform/pch information, so the removed WARN can't
ever be reached.
v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-8-git-send-email-ander.conselvan.de.oliveira@intel.com
Remove the clock calculation from ironlake_crtc_compute_clock() when the
encoder compute_config() already set one. The value was just thrown away
in that case.
Note that the previously set clock is not validated against the limits
anymore. That is ok since the fixed clocks from DP and SDVO are within
the supported range, so the call to ironlake_compute_clocks() would
never fail in that case.
v2: Add note about not checking fixed clocks agains limits. (Maarten)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-7-git-send-email-ander.conselvan.de.oliveira@intel.com
The function intel_ironlake_limit() is only called by the crtc compute
clock path. By merging it into ironlake_compute_clocks(), the code gets
clearer, since there's no more if-ladders to follow.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-4-git-send-email-ander.conselvan.de.oliveira@intel.com
The wait for other gens was added in commit 564ed191f5 ("drm/i915:
gmch: fix stuck primary plane due to memory self-refresh mode") since
that's necessary when disabling cxsr. However, cxsr disabling was later
moved to intel_pre_disable_primary() in commit 87d4300a7d ("drm/i915:
Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use
it there.") and that function got its own vblank wait for cxsr in commit
262cd2e154 ("drm/i915: CHV DDR DVFS support and another watermark
rewrite"). So remove the extra vblank wait from i9xx_crtc_distable().
Cc: Kalyan Kondapally <kalyan.kondapally@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458634284-6080-1-git-send-email-ander.conselvan.de.oliveira@intel.com
At the end of an atomic commit, we currently wait for vblanks to
complete, call put() on the various runtime PM references, and then try
to optimize our watermarks (on platforms that need two-step watermark
programming). This can lead to watermark registers being programmed
while the power well is powered down. We need to wait until after
watermark optimization is complete before dropping our runtime power
references.
Note that in the future the watermark optimization is probably going to
move to an asynchronous workqueue task that happens at some arbitrary
point after vblank. When we make that change, we'll no longer
necessarily be operating under the power reference held here, so we'll
need to wrap the watermark register programmin in a call to
intel_runtime_pm_get_if_in_use() or similar.
Cc: arun.siluvery@linux.intel.com
Cc: ville.syrjala@linux.intel.com
Cc: maarten.lankhorst@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94349
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457135979-23727-1-git-send-email-matthew.d.roper@intel.com
Patch based on a previous series by Shashank Sharma.
v2: Do not read GAMMA_MODE register to figure what mode we're in
v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0
Add documentation on how the Broadcast RGB property is affected by CTM
v4: Update contributors
v5: Refactor degamma/gamma LUTs load into a single function
v6: Fix missing intel_crtc variable (bisect issue)
v7: Fix & simplify limited range matrix multiplication (Matt Roper's
comment)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com
Implement Daniel Stone's recommendation to not read registers to infer
the hardware's state.
v2: Read GAMMA_MODE register value at init (Matt Roper's comment)
v3: Read GAMMA_MODE register in intel_modeset_readout_hw_state along
with other registers (Matt Roper's comment).
v4: Mask GAMMA_MODE register with interesting bits when reading
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-3-git-send-email-lionel.g.landwerlin@intel.com
The moves a couple of functions programming the gamma LUT and CSC
units into their own file.
On generations prior to Haswell there is only a gamma LUT. From
haswell on there is also a new enhanced color correction unit that
isn't used yet. This is why we need to set the GAMMA_MODE register,
either we're using the legacy 8bits LUT or enhanced LUTs (of 10 or
12bits).
The CSC unit is only available from Haswell on.
We also need to make a special case for CherryView which is recognized
as a gen 8 but doesn't have the same enhanced color correction unit
from Haswell on.
v2: Fix access to GAMMA_MODE register on older generations than
Haswell (from Matt Roper's comments)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1458125837-2576-2-git-send-email-lionel.g.landwerlin@intel.com
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
Refer to Global GTT consistently as GGTT, thus rename dev_priv->gtt
to dev_priv->ggtt and struct i915_gtt to struct i915_ggtt.
Fix a couple of whitespace problems while at it.
v2:
- Fix a typo in commit message.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
All of this is SW only initialization so we can move them earlier. Move
the mutex init where the rest of the locks are inited. While at it also
convert dev to dev_priv.
v2:
- use the term hook instead of callback for these functions (Jani)
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-5-git-send-email-imre.deak@intel.com
Warn for the wrong mask in enable only. Disable will have the wrong mask now
because the new state is committed before disabling the old state.
Changes since v1:
- Use crtc_mask (Durgadoss)
- Rebase.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
This makes it easier to verify correct dpll setup with only a single crtc.
It is also useful to detect double dpll enable/disable.
Changes since v1:
- Rebase on top of Ander's dpll rework.
- Change debugfs active to a mask.
- Change enabled_crtcs and active_crtcs to unsigned.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Some trivial ones, first pass done with Coccinelle:
@@
@@
(
- I915_NUM_RINGS
+ I915_NUM_ENGINES
|
- intel_ring_flag
+ intel_engine_flag
|
- for_each_ring
+ for_each_engine
|
- i915_gem_request_get_ring
+ i915_gem_request_get_engine
|
- intel_ring_idle
+ intel_engine_idle
|
- i915_gem_reset_ring_status
+ i915_gem_reset_engine_status
|
- i915_gem_reset_ring_cleanup
+ i915_gem_reset_engine_cleanup
|
- init_ring_lists
+ init_engine_lists
)
But that didn't fully work so I cleaned it up with:
for f in *.[hc]; do sed -i -e s/I915_NUM_RINGS/I915_NUM_ENGINES/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_request_get_ring/i915_gem_request_get_engine/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_flag/intel_engine_flag/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_idle/intel_engine_idle/ $f; done
for f in *.[hc]; do sed -i -e s/init_ring_lists/init_engine_lists/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_cleanup/i915_gem_reset_engine_cleanup/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_status/i915_gem_reset_engine_status/ $f; done
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
After the commit below the Broxton PLL IDs had an off-by-one error, so
fix this up. Also add a missing brace at intel_shared_dpll_init(), it
happened to compile only due to the way the IS_BROXTON macro is defined.
v2:
- remove debugging left-over
Fixes: a3c988ea06 ("drm/i915: Make SKL/KBL DPLL0 managed by the shared dpll code")
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457978134-12362-1-git-send-email-imre.deak@intel.com
Whenever there's an update to the primary plane,
fbc_pre_update and fbc_post_update are called. Kill off
intel_crtc->atomic.update_fbc and now that intel_crtc->atomic
is empty, kill it off too.
Changes since v1:
- Add a intel_fbc_supports_rotation helper.
Changes since v2:
- Remove intel_fbc_supports_rotation_helper.
- Remove unrelated changes.
Changes since v3:
- Rebase
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457516145-32117-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
fb_bits is useful to have in the crtc_state for cs flips when
the code is updated to use intel_frontbuffer_flip_prepare/complete.
So calculate it in advance and move it to crtc_state. The other stuff
can be calculated in post_plane_update, and aren't useful elsewhere.
Changes since v1:
- Changing wording, remove comment about loop.
Changes since v2:
- Rebase.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457516145-32117-1-git-send-email-maarten.lankhorst@linux.intel.com
CI runs with DEBUG_WW_MUTEX_SLOWPATH, so -EDEADLK occurs a lot more.
Handle the case where drm_atomic_commit fails with -EDEADLK correctly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56D3FEF1.6070306@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 3ba86073ed)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We must wait for the hardware to exit cxsr before doing the plane
update, so add the missing vblank wait to pre_plane_update after
disabling cxsr.
We have the wait for vblank in the pre_disable_primary hook, but not in
the pre_plane_update hook. Just move the code from (and comment) from
pre_disable_primary into pre_plane_update. Well, we still have to keep
it in pre_disable_primary for these strange _noatomic codepaths, so
let's do another version of pre_disable_primary for those. Also toss
in some FIXMEs in the hope that someone will eventually clean up this
pre_disable_primary mess.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457543247-13987-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
commit 92826fcdfc ("drm/i915: Calculate watermark related members in the crtc_state, v4.")
broke thigns by removing the pre vs. post wm update distinction. We also
lost the pre plane wm update entirely for VLV/CHV from the crtc enable
path.
This caused underruns on modeset and plane enable/disable on CHV,
and often those can lead to a dead pipe.
So let's bring back the pre vs. post thing, and let's toss in an
explicit wm update to valleyview_crtc_enable() to avoid having to
put it into the common code.
This is more or less a partial revert of the offending commit.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 92826fcdfc ("drm/i915: Calculate watermark related members in the crtc_state, v4.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457543247-13987-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Include DPLL0 in the managed dplls for SKL/KBL. While it has to be kept
enabled because of it driving CDCLK, it is better to special case that
inside the DPLL code than in the higher level.
v2: Use INTEL_DPLL_ALWAYS_ON flag. (Ander)
v3: Remove extremely paranoid WARN_ONs. (Maarten)
Handle DPLL0 in skylake_get_ddi_pll() properly. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-14-git-send-email-ander.conselvan.de.oliveira@intel.com
Manage the LCPLLs used with DisplayPort, so that all the HSW/BDW DPLLs
are managed by the shared dpll code.
v2: Introduce INTEL_DPLL_ALWAYS_ON flag to please state checker. (Ander)
v3: Initialize pll->flags in intel_shared_dpll_init(). (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-13-git-send-email-ander.conselvan.de.oliveira@intel.com
Move the code for selecting and configuring HSW/BDW DDI PLLs into the
shared dpll infrastructure. With this most of the PLL selection logic
for those platforms is in one place. DisplayPort is handled separately,
but that should be fixed on a follow up patch. It also allows a small
clean up of the SPLL logic.
v2: Rebase.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-10-git-send-email-ander.conselvan.de.oliveira@intel.com
Change the type of intel_crtc_state->shared_dpll to be a pointer to a
shared dpll. With this there is no need to first convert the id stored
in the crtc state to a pointer in order to use it. It does introduce a
bit of hassle on doing the opposite.
The long term objective is to hide details about dpll ids behind the
shared dpll interface.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Create the new file intel_dpll_mgr.c and move the shared dpll code to
it. Follow up patches that reorganize pll handling will move more code
there and tweak the interface.
No functional changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457451987-17466-2-git-send-email-ander.conselvan.de.oliveira@intel.com
Generalize rawclk handling by storing it in dev_priv.
Presumably our hrawclk readout works at least for CTG and ELK
since we've been using it for DP AUX on those platforms. There
are no real docs anymore after configdb vanished, so the only
reference is the public CTG GMCH spec. What bits are listed in
that doc match our code. The ELK GMCH spec have no relevant
details unfortunately.
The PNV situation is less clear. Starting from
commit aa17cdb4f8 ("drm/i915: initialize backlight max from VBT")
we assume that the CTG/ELK hrawclk readout works for PNV as well.
At least the results *seem* reasonable for one PNV machine (Lenovo
Ideapad S10-3t). Sadly the PNV GMCH spec doesn't have the goods on
the relevant register either.
So let's keep assuming it works for PNV,ELK,CTG and read it out on
those platforms. G33 also has hrawclk according to some notes
in BSpec, but we don't actually need it for anything, so let's not
even try to read it out there.
v2: Rebase due to IS_VALLYVIEW vs. IS_CHERRYVIEW split
Use KHz() all over, and kill off a few useless temp variables
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456932138-14004-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Only planes that are part of the state should be used for recalculating
watermarks. For planes not part of the state the previous patch allows
us to re-use the old values since they're calculated even for levels
that are not actively used.
Changes since v1:
- Remove big if from intel_crtc_atomic_check.
- Remove extra newline.
- Remove memset in ilk_compute_pipe_wm.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456826842-32553-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Rather than assume the VGA dotclock is really the FDI based thing,
let's read out the real thing via iclkip, and after readout it'll
get to compare it with the FDI based number to make sure they're
in sync.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The reason for spcial casing 20MHz in the iclkip calculations is that
it would overflow the 7 bit divisor value. Let's rewrite the special
case to check for just that, and bump up auxdiv when needed. This makes
the code work for freqeuencies close to but not exactly 20MHz. The real
lower limit for auxdiv=0 is actually:
172800000/(0x7f+2)*64)=~20930 kHz, and below that we must resort to
auxdiv=1.
Actually this is all very theoretical since we limit the dotclock to
min 25MHz with CRT on all platforms. 25Mhz is actually the documented
limit in Bspec, so it seems we ought to never need to worry about the
auxdiv=1 case. But no harm in having it.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Instead of assuming we've correctly set up SPLL to run at 270Mhz for
FDI, let's use the port_clock from pipe_config which should be what
we want. This would catch problems if someone misconfigures SPLL for
whatever reason.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we check if the encoder's idea of dotclock agrees with what
we calculated based on the FDI parameters. We do this in the encoder
.get_config() hooks, which isn't so nice in case the BIOS (or some other
outside party) made a mess of the state and we're just trying to take
over.
So as a prep step to being able sanitize such a bogus state, move the
the sanity check to just after we've read out the entire state. If
we then need to sanitize a bad state, it should be easier to move the
sanity check to occur after sanitation instead of before it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Instead of repopulatin the rotation_info struct for the fb every time
we try to use the fb, we can just populate it once when creating the fb,
and later we can just copy the pre-populate struct into the gtt_view.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-10-git-send-email-ville.syrjala@linux.intel.com
Throw out a bunch of unnecessary stuff from struct intel_rotation_info,
and pull most of the remaining stuff to live under an array of
per-color plane sub-structures.
What still remains outside the sub-structure will be reorgranized later
as well, but that requires more work elsewhere so leave it be for now.
v2: Split the vma size == luma+chroma size fix to prep patch (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-8-git-send-email-ville.syrjala@linux.intel.com
intel_compute_page_offsets() gets passed a bunch of the framebuffer
metadate sepearately. Just pass the framebuffer itself to make life
simpler for the caller, and make it less likely they would make a
mistake in the order of the arguments (as most as just unsigned ints and
such).
We still pass the pitch explicitly since for 90/270 degree rotation
the caller has to pass in the right thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-7-git-send-email-ville.syrjala@linux.intel.com
intel_pin_and_fence_fb_obj() only needs the framebuffer, and the desird
rotation (to find the right GTT view for it), so no need to pass all
kinds of plane stuff.
The main motivation is to get rid of the uggy NULL plane_state handling
due to fbdev.
v2: Add a note why I really want this
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Grumpily-Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-6-git-send-email-ville.syrjala@linux.intel.com
SKL+ needs >4K alignment for tiled surfaces, so make
intel_compute_page_offset() handle it.
The way we do it is first we compute the closest tile boundary
as before, and then figure out how many tiles we need to go
to reach the desired alignment. The difference in the offset
is then added into the x/y offsets.
v2: Be less confusing wrt. units (pixels vs. bytes) (Daniel)
v3: Use u32 for offsets
Have intel_adjust_tile_offset() return the new offset (will be
useful later)
Add an offset_aligned variable (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The page aligned surface address calculation needs to know which way
things are rotated. The contract now says that the caller must pass the
rotate x/y coordinates, as well as the tile_height aligned stride in
the tile_height direction. This will make it fairly simple to deal with
90/270 degree rotation on SKL+ where we have to deal with the rotated
view into the GTT.
v2: Pass rotation instead of bool even thoughwe only care about 0/180 vs. 90/270
v3: Introduce intel_tile_dims(), and don't mix up different units so much
v4: Unconfuse bytes vs. pixels even more
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455569699-27905-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not all platforms set this callback, so NULL check it before calling it.
v2:
- Call intel_update_watermarks() on HSW+ where the callback is not set.
(Matt)
CC: Matt Roper <matthew.d.roper@intel.com>
Fixes: commit ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456776633-3401-1-git-send-email-imre.deak@intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
CI runs with DEBUG_WW_MUTEX_SLOWPATH, so -EDEADLK occurs a lot more.
Handle the case where drm_atomic_commit fails with -EDEADLK correctly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56D3FEF1.6070306@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
In addition to calculating final watermarks, let's also pre-calculate a
set of intermediate watermark values at atomic check time. These
intermediate watermarks are a combination of the watermarks for the old
state and the new state; they should satisfy the requirements of both
states which means they can be programmed immediately when we commit the
atomic state (without waiting for a vblank). Once the vblank does
happen, we can then re-program watermarks to the more optimal final
value.
v2: Significant rebasing/rewriting.
v3:
- Move 'need_postvbl_update' flag to CRTC state (Daniel)
- Don't forget to check intermediate watermark values for validity
(Maarten)
- Don't due async watermark optimization; just do it at the end of the
atomic transaction, after waiting for vblanks. We do want it to be
async eventually, but adding that now will cause more trouble for
Maarten's in-progress work. (Maarten)
- Don't allocate space in crtc_state for intermediate watermarks on
platforms that don't need it (gen9+).
- Move WaCxSRDisabledForSpriteScaling:ivb into intel_begin_crtc_commit
now that ilk_update_wm is gone.
v4:
- Add a wm_mutex to cover updates to intel_crtc->active and the
need_postvbl_update flag. Since we don't have async yet it isn't
terribly important yet, but might as well add it now.
- Change interface to program watermarks. Platforms will now expose
.initial_watermarks() and .optimize_watermarks() functions to do
watermark programming. These should lock wm_mutex, copy the
appropriate state values into intel_crtc->active, and then call
the internal program watermarks function.
v5:
- Skip intermediate watermark calculation/check during initial hardware
readout since we don't trust the existing HW values (and don't have
valid values of our own yet).
- Don't try to call .optimize_watermarks() on platforms that don't have
atomic watermarks yet. (Maarten)
v6:
- Rebase
v7:
- Further rebase
v8:
- A few minor indentation and line length fixes
v9:
- Yet another rebase since Maarten's patches reworked a bunch of the
code (wm_pre, wm_post, etc.) that this was previously based on.
v10:
- Move wm_mutex to dev_priv to protect against racing commits against
disjoint CRTC sets. (Maarten)
- Drop unnecessary clearing of cstate->wm.need_postvbl_update (Maarten)
v11:
- Now that we've moved to atomic watermark updates, make sure we call
the proper function to program watermarks in
{ironlake,haswell}_crtc_enable(); the failure to do so on the
previous patch iteration led to us not actually programming the
watermarks before turning on the CRTC, which was the cause of the
underruns that the CI system was seeing.
- Fix inverted logic for determining when to optimize watermarks. We
were needlessly optimizing when the intermediate/optimal values were
the same (harmless), but not actually optimizing when they differed
(also harmless, but wasteful from a power/bandwidth perspective).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456276813-5689-1-git-send-email-matthew.d.roper@intel.com
Currently we perform our own wait in post_plane_update,
but the atomic core performs another one in wait_for_vblanks.
This means that 2 vblanks are done when a fb is changed,
which is a bit overkill.
Merge them by creating a helper function that takes a crtc mask
for the planes to wait on.
The broadwell vblank workaround may look gone entirely but this is
not the case. pipe_config->wm_changed is set to true
when any plane is turned on, which forces a vblank wait.
Changes since v1:
- Removing the double vblank wait on broadwell moved to its own commit.
Changes since v2:
- Move out POWER_DOMAIN_MODESET handling to its own commit.
Changes since v3:
- Do not wait for vblank on legacy cursor updates. (Ville)
- Move broadwell vblank workaround comment to page_flip_finished. (Ville)
Changes since v4:
- Compile fix, legacy_cursor_flip -> *_update.
Changes since v5:
- Kill brackets.
- Add WARN_ON when wait_for_vblanks fails.
- Remove extra newlines.
- Split the checks whether vblank is needed to a separate function,
with comments why a vblank is needed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56CD84DA.5030507@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Use our newly created encoder_mask to iterate over the encoders.
This makes it possible to get the crtc power domains from the
crtc_state at any time, without any locks or having to look at
the legacy state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455108583-29227-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Instead of restoring dpms and a flag for whether a temp fb is allocated duplicate
an atomic state before the new state is committed, and commit it the old state
in intel_release_load_detect_pipe.
Changes since v1:
- Use a real atomic state. (Ville)
Changes since v2:
- Do not preserve shared_dpll any more, no need to do so. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-2-git-send-email-maarten.lankhorst@linux.intel.com
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-6-git-send-email-imre.deak@intel.com
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-5-git-send-email-imre.deak@intel.com
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-4-git-send-email-imre.deak@intel.com
The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Revieved-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-3-git-send-email-imre.deak@intel.com
The check for active_crtcs == 0 was performed by the callers, when changing
the patches I forgot to remove those hunks.
This resulted in skylake scalers still not having the correct cdclk to
calculate scaling when all crtc's were dpms off.
Fixes: 1a617b7765 ("drm/i915: Keep track of the cdclk as if all crtc's were active.")
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455614711-9045-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Instead of duplicating the functionality now that we no longer need
to preserve dpll state we can move to using the upstream suspend helper.
Changes since v1:
- Call hw readout with all mutexes held.
- Rework intel_display_suspend to only assign modeset_restore_state
on success.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56C2E686.5060803@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
RPS lock must be taken before the struct_mutex to avoid
locking inversion. So stop grabbing it for the whole
powersave initialization and instead only take it during
the sections which need it.
Also, struct_mutex is not needed any more since dedicated
RPS lock was added in:
commit 4fc688ce79
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Nov 2 11:14:01 2012 -0700
drm/i915: protect RPS/RC6 related accesses (including PCU) with a new mutex
Based on prototype patch by Chris Wilson and a subsequent
mailing list discussion involving Ville, Imre, Chris and
Daniel.
v2: More details in the commit.
v3: Use drm_gem_object_unreference_unlocked. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
VMA creation and GEM list management need the big lock.
v2:
Mutex unlock ended on the wrong path somehow. (0-day, Julia Lawall)
Not to mention drm_gem_object_unreference was there in existing
code with no mutex held.
v3:
Some callers of i915_gem_object_create_stolen_for_preallocated
already hold the lock so move the mutex into the other caller
as well.
v4:
Changed to lockdep_assert_held. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Atomic resume was preserving the dpll state because it was required
for clearing pll state correctly. If we look at the old_crtc_state
for pll to clear this is not needed and the hack can be removed.
Changes since v1:
- Rename dpll variable to old_dpll. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455022343-15222-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
This allows iteration over encoders without requiring connection_mutex.
Changes since v1:
- Add a set_best_encoder helper function and update encoder_mask inside
it.
Changes since v2:
- Relax the WARN_ON(!crtc), with explanation.
- Call set_best_encoder when connector is moved between crtc's.
- Add some paranoia to steal_encoder to prevent accidentally setting
best_encoder to NULL.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/56AA200A.6070501@linux.intel.com
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
FBC is already deactivated at this point.
Besides, nothing should be calling these lower-level function
pointers. A few months ago, the only caller of
dev_priv->fbc.deactivate was intel_pipe_set_base_atomic(), which was
the kgdboc function. But the following commit added it to the SKL
function:
commit a8d201af68
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Thu Jan 7 11:54:11 2016 +0100
drm/i915: Use plane state for primary plane updates.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454101060-23198-1-git-send-email-paulo.r.zanoni@intel.com
Make sure we do the pre_update - which also deactivates FBC - before
we actually schedule the page flip, just to make sure we don't
flip to the new FB with FBC still activated for the previous FB.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-24-git-send-email-paulo.r.zanoni@intel.com
Move intel_fbc_enable to a place where it is called regardless of the
"modeset" variable, and make sure intel_fbc_enable can be called
multiple times without intel_fbc_disable being called.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-20-git-send-email-paulo.r.zanoni@intel.com
Instead of duplicating the calls for every platform, let's just put
them in the correct places inside intel_atomic_commit. This will also
make it easier for us to move the enable call in order to support
fasbtoot.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-19-git-send-email-paulo.r.zanoni@intel.com
This opens the possibility of implementing nicer schemes to choose the
CRTC, such as checking the amount of stolen memory available, or
choosing the best pipe on platforms that don't die FBC to pipe or
plane A.
This code was written for another refactor that I ended up discarding,
so I don't actually need it, but I figured this patch would be an
improvement on its own so I kept it on the series.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-18-git-send-email-paulo.r.zanoni@intel.com
Older FBC platforms have this restriction where FBC can't be enabled
if multiple pipes are enabled. In the current code, we disable FBC
before the second pipe becomes visible.
One of the problems with this code is that the current
multiple_pipes_ok() implementation just iterates through all CRTCs
looking at their states, but it doesn't make sure that the state
locks are grabbed. It also can't just grab the locks for every CRTC
since this would kill one of the biggest advantages of atomic
modesetting.
After the recent FBC changes, we now have the appropriate locks for
the given CRTC, so we can just try to maintain the state of each CRTC
and update it once intel_fbc_pre_update is called.
As a last note, I don't have gen 2/3 machines to test this code. My
current plan is to enable FBC on just the newer platforms, so this
patch is just an attempt to get the gen 2/3 code at least looking
sane, so if one day someone decide to fix FBC on these platforms, they
may have less work to do.
Not-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (only on HSW+)
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-16-git-send-email-paulo.r.zanoni@intel.com
Instead of:
- intel_fbc_disable_crtc(crtc)
- intel_fbc_disable(dev_priv)
we now have:
- intel_fbc_disable(crtc)
- intel_fbc_global_disable(dev_priv)
This is because all the other functions that take a CRTC are called
- intel_fbc_something(crtc)
Instead of:
- intel_fbc_something_crtc(crtc)
And I also hope that the word "global" is going to help make it more
explicit that "global" is the unusual case, not the opposite.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-14-git-send-email-paulo.r.zanoni@intel.com
We'll now call intel_fbc_pre_update instead of intel_fbc_deactivate
during atomic commits. This will continue to guarantee that we
deactivate FBC and it will also update the state checking structures
at the correct time. Then, later, at the point where we were calling
intel_fbc_update, we'll only need to call intel_fbc_post_update.
Also add the proper warnings in case we don't have the appropriate
locks. Daniel mentioned the warnings will have to be removed for async
commits, but let's keep them here while we can.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-12-git-send-email-paulo.r.zanoni@intel.com
We unconditionally disable/update FBC even during the page flip
IOCTLs, and an unconditional disable/update at every atomic commit
touching the primary plane shouldn't impact PC state residency
noticeably. Besides, the code that checks for rotation is a good hint
that we may be forgetting something else, so let's leave all the
decisions to intel_fbc.c, making the code much safer.
Once we have the code to properly make FBC enable/update decisions
based on atomic states, with proper locking, then we'll be able to
evaluate whether it will be worth trying to optimize the cases where a
disable isn't needed.
v2: Upstream moved and now our patch needs to remove dev_priv.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406837-10511-1-git-send-email-paulo.r.zanoni@intel.com
Before this patch, page flips would call intel_frontbuffer_flip() and
intel_frontbuffer_flip_complete(), which would call intel_fbc_flush(),
which would call intel_fbc_update(). The problem is that drawing
operations also trigger intel_fbc_flush() calls, so it's not
guaranteed that we have the CRTC and FB locks grabbed when
intel_fbc_flush() happens, since the call trace may come from the
rendering path.
We're trying to make the FBC code grab the appropriate CRTC/FB locks,
so split the drawing and the flipping logic in order to achieve that
in later patches. So now the frontbuffer tracking code is just going
to be used for frontbuffer drawing, and intel_fbc_update() is going to
be used directly for actual page flips.
As a note, we don't need to call intel_fbc_flip() during the two
places where we call intel_frontbuffer_flip() since in one of them we
already have an intel_fbc_update() call, and in the other we have the
planes disabled.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-7-git-send-email-paulo.r.zanoni@intel.com
The fb_modifiers and cpp arguments passed to intel_tile_width() in
intel_fill_fb_ggtt_view() got accidentally swapped around. I'm pretty
sure I fixed this already, but could be I lost the fix accidentally
during some rebases or something. Anyway, fix it up for real.
Fixes: d9b3288ecf ("drm/i915: change intel_fill_fb_ggtt_view() to use the real tile size")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-8-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_rotation_crc/primary-rotation-90
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
In the error-handling paths of i915_gem_do_execbuffer() and
intel_crtc_page_flip(), the local pointer-to-request variables
were expected to be either valid pointers or NULL. Since
2682708 drm/i915: simplify allocation of driver-internal requests
they could also be ERR_PTR() values, so the tests need to be
updated to accommodate this case.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453978089-29127-1-git-send-email-tvrtko.ursulin@linux.intel.com
There are a number of places where the driver needs a request, but isn't
working on behalf of any specific user or in a specific context. At
present, we associate them with the per-engine default context. A future
patch will abolish those per-engine context pointers; but we can already
eliminate a lot of the references to them, just by making the allocator
allow NULL as a shorthand for "an appropriate context for this ring",
which will mean that the callers don't need to know anything about how
the "appropriate context" is found (e.g. per-ring vs per-device, etc).
So this patch renames the existing i915_gem_request_alloc(), and makes
it local (static inline), and replaces it with a wrapper that provides
a default if the context is NULL, and also has a nicer calling
convention (doesn't require a pointer to an output parameter). Then we
change all callers to use the new convention:
OLD:
err = i915_gem_request_alloc(ring, user_ctx, &req);
if (err) ...
NEW:
req = i915_gem_request_alloc(ring, user_ctx);
if (IS_ERR(req)) ...
OLD:
err = i915_gem_request_alloc(ring, ring->default_context, &req);
if (err) ...
NEW:
req = i915_gem_request_alloc(ring, NULL);
if (IS_ERR(req)) ...
v4: Rebased
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453230175-19330-2-git-send-email-david.s.gordon@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having this on stack triggers the -Wframe-larger-than=1024 and
is not nice to put such big things on the kernel stack anyway.
This required a little bit of refactoring to handle the new
failure path from vlv_force_pll_on.
v2: Corrected some whitespace.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453217117-26125-1-git-send-email-tvrtko.ursulin@linux.intel.com
This reverts commit 396e33ae20.
This commit was triggering some FIFO underrun warnings on ILK-IVB
platforms (but surprisingly not on HSW/BDW that share more or less the
same codepaths). These underruns were caught by the continuous
integration (CI) system and could be reproduced consistently when
running the basic acceptance tests (BAT) on the affected platforms.
Note that this revert will cause a visible regression for some
end-users; the "flicker when mouse moves between monitors in X" issue
that was reported before this patch was merged will now return. However
regressions that are visible to CI have higher priority since they
prevent proper testing of future patches on those platforms. Hopefully
we'll be able to figure out the cause of the underruns quickly and
remerge an improved version of this patch to fix the regression.
Cc: Daniel Vetter <daniel@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93640
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453232584-8543-1-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pass BIT(DRM_ROTATE_0) instead of DRM_ROTATE_0 to skl_update_scaler().
The former is a mask, the latter just the bit number.
Fortunately the only thing skl_update_scaler() does with the rotation
is check if it's 90/270 degrees or not, and so in this case it would
still do the right thing.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1444917718-28495-1-git-send-email-ville.syrjala@linux.intel.com
Fixes: 6156a45602 ("drm/i915: skylake primary plane scaling using shared scalers")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
On SKL+ plane scaling is mutually exclusive with color keying. The code
check for this, but during some refactoring the code got changed to
also reject primary plane windowing when color keying is used. There is
no such restriction in the hardware, so restore the original logic.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 061e4b8d65 ("drm/i915: clean up atomic plane check functions, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452883613-28549-1-git-send-email-ville.syrjala@linux.intel.com
Cc: stable@vger.kernel.org
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pull in Dave's drm-next pull request to have a clean base for 4.6.
Also, we need the various atomic state extensions Maarten recently
created.
Conflicts are just adjacent changes that all resolve to nothing in git
diff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
misc i915 fixes all over the place.
* tag 'drm-intel-next-fixes-2016-01-14' of git://anongit.freedesktop.org/drm-intel:
drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page
drm/i915: Widen return value for reservation_object_wait_timeout_rcu to long.
drm/i915: intel_hpd_init(): Fix suspend/resume reprobing
drm/i915: shut up gen8+ SDE irq dmesg noise, again
drm/i915: Restore inhibiting the load of the default context
drm/i915: Tune down rpm wakelock debug checks
drm/i915: Avoid writing relocs with addresses in non-canonical form
drm/i915: Move Braswell stop_machine GGTT insertion workaround
Since your main drm-next pull isn't out of the door yet I figured I might
as well flush out drm-misc instead of delaying for 4.6. It's really just
random stuff all over, biggest thing probably connector_mask tracking from
Maarten.
* tag 'topic/drm-misc-2016-01-17' of git://anongit.freedesktop.org/drm-intel: (24 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/sysfs: use kobj_to_dev()
drm/i915: Init power domains early in driver load
drm: Do not set connector->encoder in drivers
apple-gmux: Add initial documentation
drm: move MODULE_PARM_DESC to other file
drm/edid: index CEA/HDMI mode tables using the VIC
drm/atomic: Remove drm_atomic_connectors_for_crtc.
drm/i915: Update connector_mask during readout, v2.
drm: Remove opencoded drm_gem_object_release_handle()
drm: Do not set outparam on error during GEM handle allocation
drm/docs: more leftovers from the big vtable documentation pile
drm/atomic-helper: Reject legacy flips on a disabled pipe
drm/atomic: add connector mask to drm_crtc_state.
drm/tegra: Use __drm_atomic_helper_reset_connector for subclassing connector state, v2.
drm/atomic: Add __drm_atomic_helper_connector_reset, v2.
drm/i915: Set connector_state->connector using the helper.
drm: Use a normal idr allocation for the obj->name
drm: Only bump object-reference count when adding first handle
drm: Balance error path for GEM handle allocation
...
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
commit 996a2239f9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 19 11:24:34 2013 +0200
drm/i915: Disable high-bpc on pre-1.4 EDID screens
Cc: stable@vger.kernel.org
Reported-and-tested-by: Dihan Wickremasuriya <nayomal@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452695720-7076-1-git-send-email-jani.nikula@intel.com
Add a common function to return "on" or "off" string based on the
argument, and drop the local versions of it.
This is the onoff version of
commit 42a8ca4cb4
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Aug 27 16:23:30 2015 +0300
drm/i915: add yesno utility function
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452768814-29787-1-git-send-email-jani.nikula@intel.com
Pull the code to determine the surface alignment for both linear and
tiled surfaces into a separate function intel_surf_alignment(). This
will be used not only for the vma alignment but actually aligning
the plane SURF once SKL+ starts using intel_compute_page_offset()
(since SKL+ needs >4K alignment for tiled surfaces too).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-8-git-send-email-ville.syrjala@linux.intel.com
Since intel_gen4_compute_page_offset() can now handle tiling formats
all the way down to gen2, rename it to intel_compute_tile_offset().
Not that we actually use it on gen2/3 since there's no DSPSURF etc.
registers which would take a page aligned address.
v2: s/page/tile/ (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-7-git-send-email-ville.syrjala@linux.intel.com
Use the actual tile size as to compute stuff in
intel_fill_fb_ggtt_view() instead of assuming it's PAGE_SIZE. I suppose
it doesn't matter since we don't use the results on gen2 platforms
where the tile size is 2k.
v2: Update due to CbCr plane
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-5-git-send-email-ville.syrjala@linux.intel.com
I find more usual to think about tile widths than heights, so changing
the intel_tile_height() to calculate the tile height as
tile_size/tile_width is easier than the opposite to the poor brain.
v2: Reorder arguments for consistency
Constify dev_priv arguments
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-4-git-send-email-ville.syrjala@linux.intel.com
Pull the tile width calculations from intel_fb_stride_alignment() into a
new function intel_tile_width().
Also take the opportunity to pass aroun dev_priv instead of dev to
intel_fb_stride_alignment().
v2: Reorder argumnents to be more consistent with other functions
Change intel_fb_stride_alignment() to accept dev_priv instead of dev
v3: Deal with Y tilling (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452625717-9713-3-git-send-email-ville.syrjala@linux.intel.com
Since
commit ac9b823655
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Nov 27 18:55:26 2015 +0200
drm/i915: Introduce a gmbus power domain
gmbus also needs the power domain infrastructure right from the start,
since as soon as we register the i2c controllers someone can use them.
v2: Adjust cleanup paths too (Chris).
v3: Rebase onto -nightly (totally bogus tree I had lying around) and
also move dpio init head (Ville).
v4: Ville instead suggested to move gmbus setup later in the sequence,
since it's only needed by the modeset code.
v5: Move even close to the actual user, right next to the comment that
states where we really need gmbus (and interrupts!).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: ac9b823655 ("drm/i915: Introduce a gmbus power domain")
Cc: stable@vger.kernel.org
References: http://www.spinics.net/lists/intel-gfx/msg83075.html
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452682528-19437-1-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a spurious warning from an integer overflow on 64-bits systems.
The function may return MAX_SCHEDULE_TIMEOUT which gets truncated to -1.
Explicitly handling this by casting to lret fixes it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-and-tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 3c28ff22f6 ("i915: wait for fence in prepare_plane_fb")
Link: http://patchwork.freedesktop.org/patch/msgid/5666EEC8.2000403@linux.intel.com
(cherry picked from commit bcf8be279c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
sanitize_watermarks() does not properly handle errors returned by
drm_atomic_helper_duplicate_state(). Make failures drop locks before
returning. We also change the lock of connection_mutex to a
drm_modeset_lock_all_ctx() to make sure any EDEADLK's are handled
earlier.
v2: Change call to lock connetion_mutex with a call to
drm_modeset_lock_all_ctx(). This ensures that any lock contention
is handled earlier and drm_atomic_helper_duplicate_state() won't
return EDEADLK. (Maarten)
v3: Drop locks properly in more error paths. (Maarten)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452611617-32144-1-git-send-email-matthew.d.roper@intel.com
We use the vblank timestamps to generate the vblank frame counter value
on gen2. That means we need the pipe scanout position to be accurate
when we call drm_crtc_vblank_on(), otherwise the frame counter
guesstimate may jump when the pipe actually start.
What I observed on my 85x is that the DSL initially reads 0, and when
the pipe actually starts DSL jumps to vblank_start. On gen2 DSL==0 means
actually vtotal-1 (see update_scanline_offset()), so if we initially
get vtotal-1, and then very quickly vblank_start (or thereabouts), the
scanout position will appear to jump backwards by approximately one
vblank length. Which means the frame counter guesstimate will also
jump backwards. That's no good, so let's make sure the pipe has
started before we call drm_crtc_vblank_on().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450110229-30450-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the ddi buffer translation programming to occur from the encoder
.pre_enable() hook, for just the ddi port we are enabling. Previously
we used to reprogram the translations for all ddi ports during
init and during power well enabling.
v2: s/intel_prepare_ddi_buffers/intel_prepare_ddi_buffer/ (Daniel)
Resolve conflicts due to dev_priv->atomic_cdclk_freq
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a spurious warning from an integer overflow on 64-bits systems.
The function may return MAX_SCHEDULE_TIMEOUT which gets truncated to -1.
Explicitly handling this by casting to lret fixes it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-and-tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 3c28ff22f6 ("i915: wait for fence in prepare_plane_fb")
Link: http://patchwork.freedesktop.org/patch/msgid/5666EEC8.2000403@linux.intel.com
We have done unclaimed register access check in normal
(mmio_debug=0) mode once per write. This adds probability
of finding the exact sequence where we did the bad access, but
also adds burden to each write.
As we have mmio_debug available for more fine grained analysis,
give up accuracy of detecting correct spot at the first occurrence
by doing the one shot detection and arming of mmio_debug in hangcheck
and in modeset. This removes the write path performance burden.
v2: Remove gratuitous DRM_DEBUG and return value, comments (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450250808-14864-1-git-send-email-mika.kuoppala@intel.com
In addition to calculating final watermarks, let's also pre-calculate a
set of intermediate watermark values at atomic check time. These
intermediate watermarks are a combination of the watermarks for the old
state and the new state; they should satisfy the requirements of both
states which means they can be programmed immediately when we commit the
atomic state (without waiting for a vblank). Once the vblank does
happen, we can then re-program watermarks to the more optimal final
value.
v2: Significant rebasing/rewriting.
v3:
- Move 'need_postvbl_update' flag to CRTC state (Daniel)
- Don't forget to check intermediate watermark values for validity
(Maarten)
- Don't due async watermark optimization; just do it at the end of the
atomic transaction, after waiting for vblanks. We do want it to be
async eventually, but adding that now will cause more trouble for
Maarten's in-progress work. (Maarten)
- Don't allocate space in crtc_state for intermediate watermarks on
platforms that don't need it (gen9+).
- Move WaCxSRDisabledForSpriteScaling:ivb into intel_begin_crtc_commit
now that ilk_update_wm is gone.
v4:
- Add a wm_mutex to cover updates to intel_crtc->active and the
need_postvbl_update flag. Since we don't have async yet it isn't
terribly important yet, but might as well add it now.
- Change interface to program watermarks. Platforms will now expose
.initial_watermarks() and .optimize_watermarks() functions to do
watermark programming. These should lock wm_mutex, copy the
appropriate state values into intel_crtc->active, and then call
the internal program watermarks function.
v5:
- Skip intermediate watermark calculation/check during initial hardware
readout since we don't trust the existing HW values (and don't have
valid values of our own yet).
- Don't try to call .optimize_watermarks() on platforms that don't have
atomic watermarks yet. (Maarten)
v6:
- Rebase
v7:
- Further rebase
v8:
- A few minor indentation and line length fixes
v9:
- Yet another rebase since Maarten's patches reworked a bunch of the
code (wm_pre, wm_post, etc.) that this was previously based on.
v10:
- Move wm_mutex to dev_priv to protect against racing commits against
disjoint CRTC sets. (Maarten)
- Drop unnecessary clearing of cstate->wm.need_postvbl_update (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452108870-24204-1-git-send-email-matthew.d.roper@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
drm/i915: Update connector_mask during readout, v2.
The connector_mask may be used any time during the non-atomic
.crtc_disable which is called before the full atomic state is
set up and needs to be accurate for that reason.
Changes since v1:
- Update connector_mask in readout_hw_state and add a comment.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/568D1C55.8010001@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
