Broxton and Skylake have the same behavior on display audio. So this patch
applys Skylake fix-ups to Broxton.
Signed-off-by: Lu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally we have a proper infrastructure to generate the modaliases
automatically, let's move to hda_device_id from the legacy
hda_codec_preset that contains basically the same information.
The patch function hook is stored in driver_data field, which is long,
and we need an explicit cast. Other than that, the conversion is
mostly straightforward. Each entry is even simplified using a macro,
and the lengthy (and error-prone) manual modaliases got removed.
As a result, we achieved a quite good diet:
14 files changed, 407 insertions(+), 595 deletions(-)
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For display audio, call the sync_audio_rate callback function
to do the synchronization between gfx driver and audio driver.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The port_mst_index parameter was reserved for future use, but
maintainers prefer to add it later when it is actually used.
[Note: this is an update patch to commit [51e1d83cab: drm/i915: Call
audio pin/ELD notify function] where I mistakenly applied the older
version. Jani and Daniel's review tags were to the latest version,
so I add them below, too -- tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Whenever there is an event from the i915 driver, wake the codec
and recheck plug/unplug + ELD status.
This fixes the issue with lost unsol events in power save mode,
the codec and controller can now sleep in D3 and still know when
the HDMI monitor has been connected.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit [fa4f18b4f4: ALSA: hda - Refresh widgets sysfs at
probing Haswell+ HDMI codecs], snd_hdac_refresh_widget_sysfs() is
explicitly called in the codec driver. But this results in refreshing
twice, as snd_hdac_refresh_widget_sysfs() itself calls
snd_hdac_refresh_widgets() function.
Instead, we can replace the call in snd_hda_codec_update_widgets()
with snd_hdac_refresh_widget_sysfs(). This also fixes the missing
sysfs update for ca0132, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel Haswell (and later) codec refreshes the widgets tree to expose
the whole widget nodes at probing. However, this refresh was missing
for sysfs tree.
This patch adds the missing piece, as we have now a proper API.
Reported-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de007d is used by a yet-to-be-named GPU chip.
This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is
appropriate here.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x8086280a) and module alias for Broxton
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_info_free_entry() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable runtime PM of the HDMI audio codec on the latest Intel platforms.
So the HD-A controller or HDMI codec can suspend when idle timeout by
default and release the GFX power well.
The patch influences HSW/BDW/BYT/BSW/SKL. Eariler platforms and third
party analog codecs will not be influenced.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For SKL, only the HDMI codec is in the display power well while the
HD-A controller isn't. So the controller flag 'need_i915_power' is
not set to release the display power after probe, and the codec flag
'link_power_control' is set to request/release the display power via
bus link_power ops.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We may disable proc fs only for sound part, to reduce ALSA
memory footprint. So add CONFIG_SND_PROC_FS and replace the
old CONFIG_PROC_FSs in alsa code.
With sound proc fs disabled, we can save about 9KB memory
size on X86_64 platform.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra210 contains a similar codec as Tegra124 and can be supported using
the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra114 contains the same codec as Tegra124 and can be supported using
the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra30 contains the same codec as Tegra124 and can be supported using
the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDMI codec on NVIDIA Tegra SoCs has a feature that doesn't exist on
the MCP or GPU variants. The highest bit in the vendor-defined scratch
registers can be used to trigger an interrupt in the HDMI codec, which
is signalled to the HDMI driver. This can be used to pass information,
such as the HDA format, to the HDMI driver so that it can reconfigure
itself accordingly.
While at it, change the name of the codec to Tegra124 since there are no
other SoCs in the Tegra12x family. There isn't really a Tegra12x family.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Baytrail (Valleyview) and Braswell (Cherryview), only the HDMI codec is
in the display power well while the HD-A controller isn't. So the controller
flag 'need_i915_power' is not set to release the display power after probe,
and the codec flag 'link_power_control" is set to request/release the display
power via bus link_power ops.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jack snd_kcontrols can now be created during snd_jack_new()
or by later calling snd_jack_add_new_kctls().
This patch creates the jacks during the initialisation stage
for both phantom and non phantom jacks.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the way to manage the resource release of proc
files: namely, let snd_info_free_entry() freeing the whole children.
This makes it us possible to drop the snd_device_*() management. Then
snd_card_proc_new() becomes merely a wrapper to
snd_info_create_card_entry().
Together with this change, now you need to call snd_info_free_entry()
for a proc entry created via snd_card_proc_new(), while it was freed
via snd_device_free() beforehand.
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, snd_hdac_power_up()/down() helpers checks whether the codec
is being in pm (suspend/resume), and skips the call of runtime get/put
during it. This is needed as there are lots of power up/down
sequences called in the paths that are also used in the PM itself. An
example is found in hda_codec.c::codec_exec_verb(), where this can
power up the codec while it may be called again in its power up
sequence, too.
The above works in most cases, but sometimes we really want to wait
for the real power up. For example, the control element get/put may
want explicit power up so that the value change is assured to reach to
the hardware. Using the current snd_hdac_power_up(), however,
results in a race, e.g. when it's called during the runtime suspend is
being performed. In the worst case, as found in patch_ca0132.c, it
can even lead to the deadlock because the code assumes the power up
while it was skipped due to the check above.
For dealing with such cases, this patch makes snd_hdac_power_up() and
_down() to two variants: with and without in_pm flag check. The
version with pm flag check is named as snd_hdac_power_up_pm() while
the version without pm flag check is still kept as
snd_hdac_power_up(). (Just because the usage of the former is fewer.)
Then finally, the patch replaces each call potentially done in PM with
the new _pm() variant.
In theory, we can implement a unified version -- if we can distinguish
the current context whether it's in the pm path. But such an
implementation is cumbersome, so leave the code like this a bit messy
way for now...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96271
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patches, this patch converts also to the regmap, at
this time, the cached verb writes are the target. But this conversion
needs a bit more caution than before.
- In the old code, we just record any verbs as is, and restore them at
resume. For the regmap scheme, this doesn't work, since a few verbs
like AMP or DIGI_CONVERT are asymmetrical. Such verbs are converted
either to the dedicated function (snd_hda_regmap_xxx_amp()) or
changed to the unified verb.
- Some verbs have to be declared as vendor-specific ones before
accessing via regmap.
Also, the minor optimization with codec->cached_write flag is dropped
in a few places, as this would confuse the operation. Further
optimizations will be brought in the later patches, if any.
This conversion ends up with a drop of significant amount of codes,
mostly the helper codes that are no longer used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the amp access functions to the regmap helpers.
The amp values were formerly cached in the own hash table. Now it's
dropped by the regmap's cache.
The only tricky conversion is snd_hda_codec_amp_init(). This function
shouldn't do anything if the amp was already initialized. For
achieving this behavior, a value is read once at first temporarily in
the cache-only mode. Only if it returns an error, i.e. the item
still doesn't exist in the cache, it proceeds to the update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The events that are handled by HD-audio drivers are no frequent and
urgent ones, so we can use the standard workqueue without any problem
nowadays.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the hda_codec object kept the hda_pcm list in an array, and
the codec driver was expected to assign the array. However, this
makes the object life cycle management harder, because the assigned
array is freed at the codec driver detach while it might be still
accessed by the opened streams.
In this patch, we allocate each hda_pcm object dynamically and manage
it as a linked list. Each object has a kref refcount, and both the
codec driver binder and the PCM open/close touches it, so that the
object won't be freed while in use.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the codec object to have an individual card pointer. Not only
this simplifies the redirections in many places, also this will allow
us to make each codec assigned to a different card object.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we create the standard HD-audio bus (/sys/bus/hdaudio), and bind
the codec driver with the codec device over there. This is the first
step of the whole transition so that the changes to each codec driver
are kept as minimal as possible.
Each codec driver needs to register hda_codec_driver struct containing
the currently existing preset via the new helper macro
module_hda_codec_driver(). The old hda_codec_preset_list is replaced
with this infrastructure. The generic parsers (for HDMI and other)
are also included in the preset with the special IDs to bind
uniquely.
In HD-audio core side, the device binding code is split to
hda_bind.c. It provides the snd_hda_bus_type implementation to match
the codec driver with the given codec vendor ID. It also manages the
module auto-loading by itself like before: when the matching isn't
found, it tries to probe the corresponding codec modules, and finally
falls back to the generic drivers. (The special ID mentioned above is
set at this stage.)
The only visible change to outside is that the hdaudio sysfs entry now
appears in /sys/bus/devices, not as a sound class device.
More works to move the suspend/resume and remove ops will be
(hopefully) done in later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0072 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Skylake and Haswell have the same behavior on display audio. So this patch
applys Haswell fix-ups to Skylake.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862809) and module alias for Skylake
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ELD ALSA control change event is sent by hdmi_present_sense() when
eld_changed is true.
Currently, it is only true when the ELD buffer contents have been
modified. However, the user-visible ELD controls also change to a
zero-length value and back when eld_valid is unset/set, and no event is
currently sent in such cases (such as when unplugging or replugging a
sink).
Fix the code to always set eld_changed if eld_valid value is changed,
and therefore to always send the change event when the user-visible
value changes.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, hda_jack infrastructure allows only one callback per jack, and
this makes things slightly complicated when a driver wants to assign
multiple tasks to a jack, e.g. the standard auto-mute with a power
up/down sequence. This can be simplified if the hda_jack accepts
multiple callbacks.
This patch is such an extension: the callback-specific part (the
function and private_data) is split to another struct from
hda_jack_tbl, and multiple such objects can be assigned to a single
hda_jack_tbl entry.
The new struct hda_jack_callback is passed to each callback function
now, thus the patch became bigger than expected. But these changes
are mostly trivial.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The action value assigned to each hda_jack_tbl entry is mostly
superfluous. The actually used values are either the widget NID or a
value specific to the callback.
The former case can be simply replaced by a reference to widget NID
itself. The only place doing the latter is STAC/IDT codec driver for
the powermap handling. But, the code doesn't need to check the action
field at all -- the function jack_update_power() is called either with
a specific pin or with NULL. So the check of jack->action can be
removed completely there, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Valleyview and Cherryview have the same behavior on display audio. So this patch
defines is_valleyview_plus() to include codecs for both Valleyview and its successor
Cherryview, and apply Valleyview fix-ups to Cherryview.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both Haswell and Broadwell need set depop_delay to 0. So apply this
setting to haswell plus.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862883) and module alias for Braswell
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since init_failed flag was moved to struct hda_intel, its access in
the commit [4da63c6f: ALSA: hda - Fix broken PM due to incomplete
i915 initialization] is also replaced with hda->init_failed
appropriately.
Vendor ID 0x10de0070 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to call the proper init function in case it has been
overridden, as it might restore things that the generic routing
doesn't know anything about. E.g. AMD cards have special verbs
that need resetting.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=77901
Fixes: 5a61358433 ('ALSA: hda - hdmi: Add ATI/AMD multi-channel audio support')
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Cc: <stable@vger.kernel.org> [v3.13+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch will verify the pin's coverter selection for an active stream
when an unsol event reports this pin becomes available again after a display
mode change or hot-plug event.
For Haswell+ and Valleyview: display mode change or hot-plug can change the
transcoder:port connection and make all the involved audio pins share the 1st
converter. So the stream using 1st convertor will flow to multiple pins
but active streams using other converters will fail. This workaround
is to assure the pin selects the right conveter and an assigned converter is
not shared by other unused pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0071 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently infoframe contents and channel mapping are only set when a
sink (monitor) is present.
However, this does not make much sense, since
1) We can make a very reasonable guess on CA after 18e391862c ("ALSA:
hda - hdmi: Fallback to ALSA allocation when selecting CA") or by
relying on a previously valid ELD (or we may be using a
user-specified channel map).
2) Not setting infoframe contents and channel count simply means they
are left at a possibly incorrect state - playback is still allowed
to proceed (with missing or wrongly mapped channels).
Reasons for monitor_present being 0 include disconnected cable, video
driver issues, or codec not being spec-compliant. Note that in
actual disconnected-cable case it should not matter if these settings
are wrong as they will be re-set after jack detection, though.
Change the behavior to allow the infoframe contents and the channel
mapping to be set even without a sink/monitor, either based on the
previous valid ELD contents, if any, or based on sensible defaults
(standard channel layouts or provided custom map, sink type HDMI).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Stephan Raue <stephan@openelec.tv>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().
Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).
Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.
However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Stephan Raue <stephan@openelec.tv>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a temporary fix for some Intel HDMI codecs to avoid no sound output for
a resuming playback after S3.
After S3, the audio driver restores pin:cvt connection selections by
snd_hda_codec_resume_cache(). However this can happen before the gfx side is
ready and such connect selection is overlooked by HW. After gfx is ready, the
pins make the default selection again. And this will cause multiple pins share
a same convertor and mute control will affect each other. Thus a resumed audio
playback become silent after S3.
This patch verifies pin:cvt connection on preparing a stream, to assure the pin
selects the right convetor and an assigned convertor is not shared by other
unused pins. Apply this fix-up on Haswell, Broadwell and Valleyview (Baytrail).
We need this temporary fix before a reliable software communication channel is
established between audio and gfx, to sync audio/gfx operations.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch initialized the local audio InfoFrame variable 'ai' to be all zero,
thus the data bytes will indicate "Refer to Stream Header" by default.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use dev_err() and co for messages from HD-audio controller and codec
drivers. The codec drivers are mostly bound with codec objects, so
some helper macros, codec_err(), codec_info(), etc, are provided.
They merely wrap the corresponding dev_xxx().
There are a few places still calling snd_printk() and its variants
as they are called without the codec or device context.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 384a48d715 "ALSA: hda: HDMI: Support codecs with fewer cvts
than pins" dynamically enabled each pin widget's PIN_OUT only when the
pin was actively in use. This was required on certain NVIDIA CODECs for
correct operation. Specifically, if multiple pin widgets each had their
mux input select the same audio converter widget and each pin widget had
PIN_OUT enabled, then only one of the pin widgets would actually receive
the audio, and often not the one the user wanted!
However, this apparently broke some Intel systems, and commit
6169b67361 "ALSA: hda - Always turn on pins for HDMI/DP" reverted the
dynamic setting of PIN_OUT. This in turn broke the afore-mentioned NVIDIA
CODECs.
This change supports either dynamic or static handling of PIN_OUT,
selected by a flag set up during CODEC initialization. This flag is
enabled for all recent NVIDIA GPUs.
Reported-by: Uosis <uosisl@gmail.com>
Cc: <stable@vger.kernel.org> # v3.13
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell and Haswell have the same behavior on display audio. So this patch
defines is_haswell_plus() to include codecs for both Haswell and its successor
Broadwell, and apply all Haswell fix-ups to Broadwell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862808) and module alias for Broadwell
display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case a single HDA card has both HDMI and S/PDIF outputs, the S/PDIF
outputs will have their IEC958 controls created starting from index 16
and the HDMI controls will be created starting from index 0.
However, HDMI simple_playback_build_controls() as used by old VIA and
NVIDIA codecs incorrectly requests the IEC958 controls to be created
with an S/PDIF type instead of HDMI.
In case the card has other codecs that have HDMI outputs, the controls
will be created with wrong index=16, causing them to e.g. be unreachable
by the ALSA "hdmi" alias.
Fix that by making simple_playback_build_controls() request controls
with HDMI indexes.
Not many cards have an affected configuration, but e.g. ASUS M3N78-VM
contains an integrated NVIDIA HDA "card" with:
- a VIA codec that has, among others, an S/PDIF pin incorrectly
labelled as an HDMI pin, and
- an NVIDIA MCP7x HDMI codec.
Reported-by: MysterX on #openelec
Tested-by: MysterX on #openelec
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org> # 3.8+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch skips the default depop delay before D3 for Haswell (10 ms) and
Valleyview2 (100 ms) display codec, to reduce codec suspend time.
The analog part of display audio is implemented in the external display. Some
displays have weak pop noise while others not when suspending, no matter there
is the default delay or not.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the case of using jackpoll_ms instead of unsol events, the jack
was correctly detected, but ELD info was not refreshed on plug-in.
And without ELD info, no proper restriction of pcm, which can in turn
break sound output on some devices.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to Mengdong, we shouldn't enable runtime PM when a codec
doesn't support EPSS, based on the experiences on Windows.
We have already this check in HDMI codec drivers, but now apply it in
general in hda_codec.c.
Credit goes to Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we fixed the long-standing bugs of runtime PM, let's enable
Panther Point again. The runtime PM was disabled in the HDMI codec
driver due to the S3 issue, and this should have been fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a codec contains only the digital outputs, it's very likely a
HDMI/DP codec, which isn't supported by the generic parser but via
HDMI codec parser code. Detect such a case and bind with the proper
parser object if available.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add error checks to HBR status reads (both generic and ATI/AMD) and
ATI/AMD codec reads for ELD generation.
Unchecked errors in these just caused more errors later on (invalid
codec writes for the HBR ones and ELD parsing errors for the ATI/AMD ELD
ones), but it is better to catch them earlier.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Channel map positions FLH, FCH, FRH duplicate positions TFL, TFC, TFR.
Both are the speakers above the front speakers (CEA uses "high" and USB
audio uses "top" nomenclature).
Since the USB audio code has used the TFx positions since v3.8
(04324ccc75, "ALSA: usb-audio: add channel map support") but the HDMI
code only just started using FxH in a5b7d510b2 ("ALSA: hda -
hdmi: Fix channel maps with less common speakers") which is not yet in
any released kernel, standardize on TFx instead.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.
Suggested by Anssi Hannula.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a small gap between the jack detection unsolicited event and
the time the ELD is updated. When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.
For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated. The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function name not_share_unassigned_cvt() is opposite to what it does.
This patch renames it to intel_not_share_assigned_cvt(), and addes comments
to explain why some Intel display codecs need this workaround.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NVIDIA HDMI codecs do not seem to follow the Audio Sample Packet (ASP)
channel mapping (as set by verb F32h per HDA specification 7.3.3.41)
when playing back 2-channel audio (CEA CA 0x00).
Basically this means that specifying swapped channels for stereo audio
(FR,FL) does not take effect, and e.g. this command plays back on the
wrong channel:
speaker-test -c2 -Dhdmi:CARD=NVidia,DEV=0 -m FR,FL -s1
Multichannel audio is not affected.
This issue has been confirmed to exist on codec 0x10de0015 by me and on
0x10de0040 by Juho Teperi.
Disable 2ch FL/FR channel swapping on all NVIDIA HDMI codecs that use
the standard HDA channel mapping system. Since this is a very minor
functionality loss, we err on the side of disabling it for newer codecs
as well until any future testing confirms that this issue has been
fixed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Helped-by: Juho Teperi <juho.teperi@iki.fi>
Cc: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Valleyview display codec, if an unused pin chooses an assgined converter
selected by a used pin, playback on the unused pin can also give sound to the
output device of the used pin. It's because data flows from the same convertor
to the display port of the used pin. This issue is same as Haswell.
So this patch avoids using assinged convertors for unused pins.
The related function haswell_config_cvts() is renamed for code reuse.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_setup_audio_infoframe() does not set up pin and infoframe if there
is no connected sink. If a sink is connected while audio playback is
already in progress, the pin and infoframe will not be properly set up,
causing no audio or wrongly mapped audio.
On Intel Haswell codecs the hdmi_setup_audio_infoframe() is already
called again from hdmi_present_sense() when an ELD appears because
transcoder:port mapping may have changed.
Make the call non-Haswell-specific so that audio will be properly set up
if the playback was started before a sink was connected.
Tested on non-Haswell Intel HDMI codec by plugging sink in during
playback.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD HDMI codecs (revision ID 3 and later, 0x100300 as reported by
procfs codec#0) have a configurable ramp-up/down functionality.
The documentation ( http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf )
specifies that 180 ("180/256 =~ 0.7") is recommended for PCM and 0 for
non-PCM.
Apply the recommended values according to provided S/PDIF AES0 settings
since ramp-up/down does not make sense for non-PCM.
v2: adapted to hdmi_ops infrastructure
* More note from Anssi:
actually, re-reading mails reveals that Olivier didn't find the
expected difference with this setting, except for "maybe slightly
slower startup with AES0=6" (i.e. value 0, which is unexpected).
So maybe
a) it makes too unnoticiable a difference, or
b) only affects certain hardware (card and/or sink), or
c) ramp-up/down is only triggered with the MUTE bit of
ATI_VERB_SET_MULTICHANNEL_xx which is also rev3+ specific,
but is not presently used by the driver,
or something else.
So there's a significant chance setting ramp rate is useless for us ATM,
but probably does not do actual harm either.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Olivier Langlois <olivier@trillion01.com> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD HDMI codecs do not include standard HDA HDMI HBR support (which
is required for bitstreaming DTS-HD and Dolby TrueHD), instead they have
custom verbs for checking and enabling it.
Add support for the ATI/AMD HDMI HBR verbs.
The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
v2: adapted to hdmi_ops infrastructure
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD HDMI/DP codecs do not include standard HDA ELD (EDID-like data)
support.
In place of providing access to an ELD buffer, various vendor-specific
verbs are provided to provide the relevant information. Revision ID 3
and later (0x100300 as reported by procfs codec#X) have support for
providing more information than the previous revisions (but only if
supported by the display driver).
Generate ELD from the information provided by the vendor-specific verbs
on ATI/AMD codecs.
The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
v2: moved code to hda_eld.c and cleaned it up
v3: adapted to hdmi_ops infrastructure
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD codecs do not support all the standard HDA HDMI/DP functions,
instead various vendor-specific verbs are provided.
This commit addresses these missing functions:
- standard channel mapping support
- standard infoframe configuration support
ATI/AMD provides their own verbs that allow the following:
- setting CA for infoframe
- setting down-mix information for infoframe
- channel pair remapping
- individual channel remapping (revision ID 3+, 0x100300+)
The documentation for the verbs has now been released by AMD:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
Add support for the ATI/AMD specific verbs and use them instead of the
generic methods on ATI/AMD codecs. This allows multi-channel PCM audio
to work.
Channel remapping is restricted to pairwise mapping on codecs with
revision ID 2 (0x100200 as reported by procfs codec#X) or lower. This
means cards up to Radeon HD7670 as far as I know. This will not affect
standard multi-channel modes since these codecs support automatic
FC-LFE swapping for HDMI.
ATI/AMD codecs do not advertise all of their supported rates, formats
and channel counts, therefore that information is forced accordingly so
that all HDMI 1.x PCM parameters are marked as supported.
Support for multiple ports is also added to patch_atihdmi so that
0x1002aa01 codecs with multiple ports will work properly when switched
back to that patch.
v2: splitted ELD emulation to a separate patch, tlv fixes
v3: adapted to the new hdmi_ops infrastructure, fixed rev3+ vendor id
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2+rev3fix
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upcoming AMD multichannel support requires many customized operations
(channel mapping, ELD, HBR) but can otherwise share most of its code
with the generic patch.
Add a local struct hdmi_ops containing customizable HDMI-specific
callbacks and move the current code to those callbacks. Functionality is
unaltered.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... which was introduced by the previous commit a4e9a38b, causing
build errors without CONFIG_PROC_FS.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862882) and module alias for
Valleyview2 display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the lock is used primarily in patch_hdmi.c, it's better to move
it in the local struct instead of exporting in hda_eld. The only
functions requiring the lock in hda_eld.c are proc accessors. So in
this patch, the proc entry and its creation/deletion/accessors are
moved into patch_hdmi.c, together with the mutex lock to pin_spec
struct.
The former proc info functions are exported so that they can be called
from patch_hdmi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some per_pin fields and ELD contents might be changed dynamically in
multiple ways where the concurrent accesses are still opened in the
current code. This patch fixes such possible races by using eld->lock
in appropriate places.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.
However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.
Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").
Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow channel map debugging for both automatic and manual channel maps,
and print CA always when updating infoframe.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the available channel maps TLV only contains channel maps that
are limited to the traditional 7.1 speakers.
Since the other HDMI channel mapping functions have been fixed to
properly handle all CEA-861-E specified speakers, allow them to be
listed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For some speakers and slots the CEA slot <-> speaker assignment depends
on the used CEA Channel Allocation value.
Therefore the from_cea_slot() and to_cea_slot() helpers currently only
work correctly for the regular 7.1 speakers.
Fix them to work with all speakers, taking the re-ordered CA index as
input and adapting use sites accordingly.
This change allows manual channel mapping to actually work for all CEA
allocated speakers. Additionally, this fixes incorrect channel map
reporting in automatic channel mapping mode when an affected speaker
position is used (e.g. 6.1 map which contains an RC speaker).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_manual_setup_channel_mapping() and hdmi_std_setup_channel_mapping
try to assign ALSA channels to HDMI channel slots and disable (i.e.
silence) other slots.
However, they try to disable a slot by using AC_VERB_SET_CHAN_SLOT with
parameter ((alsa_ch << 8) | 0xf), while the correct parameter is
((0xf << 8) | hdmi_slot), i.e. the slot should be unassigned, not the
ALSA channel.
Fix that by actually disabling the unused slots.
Note that this bug did not cause any (reported) issues because slots
incorrectly having audio are normally ignored by a receiver if the CEA
channel allocation used does not map that slot to any speaker.
Additionally, the converter channel count configuration limits the
number of actually active channels in any case.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the converter channel count is set to the number of actual
input channels. The audio infoframe channel count field is set
similarly.
However, sometimes the used channel map does not map all input channels
to outputs. Notably, 3 channel modes (e.g. 2.1) require a dummy input
channel so there are 4 input channels. According to the HDA
specification, converter channel count should be programmed according to
the number of _active_ channels.
On Intel HDMI codecs (but not on NVIDIA), setting the converter channel
to a higher value than there are actually mapped channels to HDMI slots
will cause no audio to be output at all.
Note that the effects of this issue are currently partially masked by
other bugs that prevent the driver from actually unmapping channels in
certain cases. For example, if a 4 channel stream is first created and
prepared, it gets a FL,FR,RL,RR mapping (ALSA->HDMI slot mapping 0->0,
1->1, 2->4, 3->5). If one thereafter assigns a FR,FL,FC mapping to it,
the driver will remap 2->3 but fail to unmap 2->4 and 3->5, so there are
still 4 active channels and the issue will not trigger in this case.
These bugs will be fixed separately.
Fix the channel counts in the converter channel count field and in the
audio infoframe channel count field to match the actual number of active
channels.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_std_setup_channel_mapping() selects a Channel Allocation according
to the sink reported speaker mask, preferring the ALSA standard layouts.
If the channel allocation is not one of the ALSA standard layouts, the
ALSA channels are mapped directly to HDMI channels in order. However,
the function does not take into account that there a holes in the HDMI
channel map.
Additionally, the function tries to disable a slot by using
AC_VERB_SET_CHAN_SLOT with parameter ((alsa_ch << 8) | 0xf), while the
correct parameter is ((0xf << 8) | hdmi_slot), i.e. the slot should be
unassigned, not the ALSA channel.
Fix both of the issues for non-ALSA-default layouts.
Tested on Intel HDMI with a speaker mask of FL | FR | FC | RC, which
causes CA 0x06 to be selected for 4-channel audio, which causes
incorrect output (sound destined to RC goes to FC and FC goes nowhere)
without the patch.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_setup_fake_chmap() is supposed to set the reported channel map when
the channel map is not specified by the user.
However, the function indexes channel_allocations[] with a wrong value
and extracts the wrong nibble from hdmi_channel_mapping[], causing wrong
channel maps to be shown.
Fix those issues.
Tested on Intel HDMI to correctly generate various channel maps, for
example 3,4,14,15,7,8,5,6 (instead of incorrect 3,4,8,7,5,6,14,0) for
standard 7.1 channel audio. (Note that the side and rear channels are
reported as RL/RR and RLC/RRC, respectively, as per the CEA-861
standard, instead of the more traditional SL/SR and RL/RR.)
Note that this only fixes the layouts that only contain traditional 7.1
speakers (2.0, 2.1, 4.0, 5.1, 7.1, etc.). E.g. the rear center of 6.1
is still being shown wrongly due to an issue with from_cea_slot()
which will be fixed in a later patch.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=oTEO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.12
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
When Gfx driver reconnects a port and transcoder, the pin amplifier will
be muted. To enable sound, the pin amp need to be unmuted.
This patch
- moves pin amp unmuting from stream preparing to hdmi_setup_audio_infoframe().
So if port:transcoder reconnection happens during stream playback, the ELDV
unsol event can stil trigger pin's amp unmuting when re-setting up audio
info frame.
- remove reading pin amp status before unmuting for speed-up, since pin amp
should always be unmuted.
- rename haswell_verify_pin_D0() to haswell_verify_D0(), since the convertor
power state is also fixed here.
This patch is mostly based on suggestion of David Henningsson.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To apply Haswell specific fixings, this patch defines is_haswell() to check
whether a display audio codec is Haswell, to avoid explicitly checking Haswell
vendor ID everywhere.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost. Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.
The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event. For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.
This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
accordingly.
The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.
The patch is mostly based on the work by Mengdong Lin.
Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: Frank Zafka <kafkaesque1978@gmail.com>
Reported-by: Peter Frühberger <fritsch@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
