Previously to this patch, the hardware was removing
VLAN tags from the inner header of VXLAN packets. The
hardware configuration can be changed to leave the
packet alone since that is what the linux stack
expects for this type of VLAN in VXLAN packet.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_vsi_filters function can be called directly under RTNL
or through the timer subtask without one. This was causing a deadlock.
If sync_vsi_filters is called from a thread which held the lock,
and in another thread the PROMISC setting got changed we would
be executing the PROMISC change in the thread which already held
the lock alongside the other filter update. The PROMISC change
requires a reset if we are on a VEB, which requires it to be called
under RTNL.
Earlier the driver would call reset for PROMISC change without
checking if we were already under RTNL and would try to grab it
causing a deadlock. This patch changes the flow to see if we are
already under RTNL before trying to grab it.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump and when
it does a WB. It also optimizes when we do a wmb.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Tx checksum encoder knows about GRE protocol and sets the
descriptor flag appropriately.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_get_head needs to be called in multiple files in a further patch,
prepare by moving the function into a header file.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to recover the result of a previously run AQ command.
Change-ID: I21afec2c20c1a5e6ba60c7fbfcbedfff78c10e45
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a facility to run AQ commands through the nvmupdate utility in order
to allow the update tools to interact with the FW and do special
commands needed for updates and configuration changes.
Change-ID: I5c41523e4055b37f8e4ee479f7a0574368f4a588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds wait states to the NVM update state machine to signify when
waiting for an update operation to finish, whether we're in the middle
of a set of Write operations, or we're now idle but waiting.
Change-ID: Iabe91d6579ef6a2ea560647e374035656211ab43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds a new GetStatus command so that the NVM update tool can query
the current status instead of doing fake write requests to probe for
readiness.
Change-ID: I671ec6ccd4dfc9dbac3a03b964589d693fda5cd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the writeback descriptor buffer was previously created, this gives it
to the AQ command request to be used to save the results.
Change-ID: I8c8a1af81e6ebed6d0a15ed31697fe1a6c4e3708
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to save the AdminQ write back descriptor if a
caller supplies a buffer for it to be saved into.
Change-ID: I3d1301d26360b39a2d66dc8569e851f54133a3af
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code returns something that becomes the errno value from ethtool and
passes around a pointer to an errno variable. This patch changes the name
slightly to differentiate it from the actual user errno variable.
Change-ID: Idaa37845c069e66f4cea072e90f471bb2142454d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes bugs where the port is not receiving multicast or VLAN tagged
packets when in promiscuous mode. This can occur when a SW bridge is
created on top of the device.
This also fixes issues where the promiscuous behavior setting was not
being preserved across a reset caused by features being enabled or
disabled.
We are using defport instead of doing a true promiscuous mode because we do
not need to receive the SRIOV or VMDq VSI directed traffic which would suck
up bandwidth and is really not intended for the SW bridge.
In addition, with defport we get VLAN promiscuous behavior which is not
possible from the VSI level promiscuous setting.
Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Change-ID: Ie3c4cf8cebabee4f15e1e3fdc4fc8a68bbca40ee
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel notifies all VXLAN capable registered drivers, i.e. any
driver that implements ndo_add_vxlan_port(), of the addition of a
port so that the driver can track which ports are in use. There's
no need to log this - it just fills the system log with useless and
irksome noise.
Also, when failing to init SR-IOV interfaces the driver was printing the
same message twice. Just remove the inner printk and let the outer message
catch enable as well as the other failures.
Change-ID: Id5ecb1d425c2a357ee2bc1635dab24553831dade
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Turns out that 'inavlid' is an inavlid spelling for 'invalid'.
Change-ID: Ie1fe2d0f8d1ba75ab880594875ec2e4152a76f61
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing comment is incorrect. Add new comment to point out that the
PF reset does not affect link but if the reset is changed to a different
type that does affect link then the link test would need to be moved to
before the reset.
Change-ID: I28d786f46e9465860babdee61c1dba51016464df
Reported-by: Jeremiah Kyle <jeremiah.kyle@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to update per VEB per TC statistics and dump
it via ethtool. It also adds a structure to hold VEB per TC statistics.
The fields can be filled by reading the GLVEBTC_* counters.
Change-ID: I28b4759b9ab6ad5a61f046a1bc9ef6b16fe31538
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Treat netqueues the same way we do virtual functions when someone wants to
run the ethtool offline diagnostic test.
Change-ID: Id48d2b933f1fd0db7be06305a93c6ebe3dc821f5
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the driver flow to take into account legacy interrupts.
Over time we added code that assumes MSIX is the only mode that the
driver runs in. It also enables a legacy workaround to trigger SWINT
when the TX ring has non-cache aligned descriptors pending and interrupts
are disabled.
We work with a single vector in MSI mode too, so apply the same
restrictions as Legacy.
Change-ID: I826ddff1f9bd45d2dbe11f56a3ddcef0dbf42563
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should be stopping the service task and flow director on
shutdown not on suspension.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The port.crc_errors is really an RX counter, so let's mark it as such.
Change-ID: I179afd3f8a95d45229bb4163a6aeb01f0d2d250b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse cries when we compare an __le16 to a u16, almost like it cares
about architectures other than x86. Weird. Use the le16_to_cpu macro to
make it stop crying.
Change-ID: Id068f4d7868a2d3df234a791a76d15938f37db35
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 does NVM update via the adminq queue, so we need to add support for
that.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports evicting ATR filters in the HW. With this patch, we enable
the feature in the driver and avoid filter deletion by the driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the i40e and i40evf register.h file with the registers for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the firmware API update to support the new X722 device.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding device ids for new hardware X722
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a little confusion in reporting error status in phy and fcoe
setup error reports by separating the return status from the AQ error.
Add two decoder functions to make this easier.
Change-ID: I960bcdeef3978a15fec1cdb5eff781d5cbae42fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver fully supports VF drivers using both the 1.0 and 1.1
versions of the virtual channel API. However, VF drivers using
version 1.0 get upset if we provide them with a version other than
that, and refuse to play with us.
Correct this by checking the VFs API version at the time that we
store it off, and provide the correct version number back to the VF
so we can all get along.
Change-ID: I86dfe02e67b2bef336b4b49a1bb072f3e7229abc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store off the VF API version for use when figuring out the VF driver
capabilities. Add support for the VF driver handing its capabilities to
the PF driver and then use this information when sending VF resource
information back to the VF driver.
Change-ID: Ic00d0eeeb5b8118085e12f068ef857089a8f7c2d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we've rolled the virtual channel API version to 1.1, add some
macros to test what version is being used by our partner in crime. For the
VF, add some macros to determine what our device capabilities are.
Change-ID: I79f6683d4c23bd76a8ad9fd492776fcc1208e1dc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prepare for the changes coming up in the X722 device and future
devices, the virtual channel interface has to change slightly. The VF
driver can now report what its capable of supporting, which then informs
the PF driver when it sends the configuration information back to the
VF.
A 1.1 VF driver on a 1.0 PF driver should not send its capabilities.
Likewise, a 1.1 PF driver controlling a 1.0 VF driver should not expect
or depend upon receiving the VF capabilities.
All other aspects of the API are unchanged.
Change-ID: I530cc55f107edd1ee8bdf95830aa90b87854058a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With a little work we can clean up some unnecessary logic jumping and
drop a variable.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the switch statement for dynamic interrupt throttling
and adds a default case. With this patch, we check the latency setting
instead of the current ITR settings and the included refactor improves
performance.
Without this patch, the ITR setting would never change dynamically, and
there was no default.
Change-ID: Idb5a8a14c7109ec47c90f6e94bd43baa17d7ee37
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I84573d9fa51effc5b29bf5b8c74e3cc8b2673f48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change a warning message to indicate what may have really happened when
the init_shared_code call fails.
Change-ID: I616ace40fed120d0dec86dfc91ab2d7cde466904
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_add_pd_table_entry() routine is being modified to handle both
cases where a backing page is passed and where backing page is allocated
in i40e_add_pd_table_entry().
For PBLE resource management, it is more efficient for it to manage its
backing pages. For VF, PBLE backing page addresses will be send to PF
driver for PBLE resource.
The i40e_remove_pd_bp() is also modified to not free pre-allocated pages and
free only ones which were allocated in i40e_add_pd_table_entry().
Change-ID: Ie673f0403f22979e9406f5a94048dceb91bcf9a8
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF is disabled, there is no way for it to recover until either
the PF driver is reloaded or SR-IOV is disabled and enabled. To correct
this, enable the VF after a successful reset.
Change-ID: I9e0788476c4d53d5407961b503febdfff2b8a7c6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF disable code was just whanging on the reset bit without properly
cleaning up the VF, which would leave the VF in an indeterminate state
from which it could not recover. Fix this by notifying the VF and then
by calling the normal VF reset routine.
Change-ID: I862b9dfa919368773cbdc212b805b520db2f7430
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MAC filters for VFs were being programmed with 0 for the VLAN value when
there was no VLAN assigned. This is incorrect and actually assigns the
VF to VLAN 0. Instead, we must use -1 to indicate that no VLAN is in
use. This change programs the filters correctly and gets rid of a bogus
error message when setting a port VLAN on an active VF.
Change-ID: Ica9a9906d768405377ff3308e27f7d0b5b2ea96e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the necessary updates to i40e_adminq_cmd.h.
Change-ID: Ib031c86cc6cab78e5aa44c64d8ce5474be8d7e42
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some #ifdef's that should not be there. They
were stopping code that is needed from being compiled in.
With these #ifdef's removed, changes are needed in the driver
to fix some compile errors: adding missing parameters to
the definition of ndo_bridge_setlink and a ndo_dflt_brige_getlink call.
Change-ID: I5516614e1bc50b6bca0647cef971bc96161ba2de
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If user attempts to set a port VLAN on a VF that already has the same
port VLAN configured, the driver will go through a completely
unnecessary flurry of filter removals and filter adds. Just check for
this condition and return success instead of doing a bunch of busywork.
Change-ID: Ia1a9e83e6ed48b3f4658bc20dfc6af0cf525d54a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a prefetch for the next Tx descriptor to be used when we know
there are more coming.
Change-ID: Ibb9acab11d508eec2db7da795df74debc16eeacb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Flex10 device/function capability has been upgraded to include
information needed to support Flex-10 configurations. This patch adds new
fields to the i40e_hw_capabilities structure and updates
i40e_parse_discover_capabilities functions to extract them from the AQ
response. Naming convention has changed to use flex10 mode instead of
existing mfp_mode_1.
Change-ID: I305dd888866985a30293acb3fb14fa43ca6b79ea
Signed-off-by: Pawel Orlowski <pawel.orlowski@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the driver can dynamically enable/disable FD ATR and SB features,
these stats help keep track of the current state and along with
fd_flush count provide a means to debug what could be going on
with the flow director filters. This will take away the need for
being verbose in our debug logs with respect to FD.
Change-ID: I29224f750fe6602391043655d18996570720377d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e supports UDP tunnel headers up to 80 bytes in length, so
this adds a check to ensure that it doesn't try to offload
packets that exceed that.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I54ec2787a9fead5e18447078f26e5dd27f01da44
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver doesn't use the time_stamp member to determine if there is a
tx_hang any more. There really isn't any point to the variable at all
so just remove it. It was left over from a previous tx_hang design.
Change-ID: I4c814827e1bcb46e45118fe37acdcfa814fb62a0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inlining these functions gives us about 15% more 64 byte packets per
second when using pktgen. 13.3 million to 15 million with a single
queue.
Also fix the function names in i40evf to i40evf not i40e while we are
touching the function header.
Change-ID: I3294ae9b085cf438672b6db5f9af122490ead9d0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are not useful unless SV is happening as there is a FD flush counter
that tracks this.
Change-ID: If2655b5a29687247d03a51d35f69854bbeb711ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because i40e_fcoe_ctxt_eof should never be called without
i40e_fcoe_eof_is_supported being called first, the EOF in fcoe_ctxt_eof
should always be valid and therefore we do not need to print an error
if it is not valid.
However, a WARN ON to easily catch any calls to i40e_fcoe_ctxt_eof that
aren't preceded with a call to i40e_fcoe_eof_is_supported is helpful.
Change-ID: I3b536b1981ec0bce80576a74440b7dea3908bdb9
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need for a counter so remove the TODO comment.
Change-ID: I3321dda04934c4f5fda9b279ab666192bda44214
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can use the stat index macro directly, a variable is not required.
Change-ID: I19f08ac16353dc0cd87a1a8248d714e15a54aa8a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a 3rd dynamic filter counter to track Tunneled ATR hits separately.
Ethtool port stat "fdir_atr_tunnel_match"
Change-ID: Idd978b6db2a462b5722397cd2ffd04ef055f8655
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this, RSS would have done inner header load balancing. Now we can
get the benefits of ATR for tunneled packets to better align TX and RX
queues with the right core/interrupt.
Change-ID: I07d0e0a192faf28fdd33b2f04c32b2a82ff97ddd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Require the user to disable virtual functions before running the device
offline diagnostics. The offline diagnostics are intended to ensure
basic operation of the device - it is beyond the scope of the diagnostic
test to handle the additional complexity of bringing all the virtual
functions offline and then back online for each test run.
Change-ID: Ic0b854851a09fc85df0c9e82c220e45885457c30
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PFC is enabled for any UP in single TC configuration the driver didn't
collect the PFC XOFF RX stats. Though a single TC with PFC enabled is not a
common scenario do not prevent the driver from collecting stats if firmware
indicates that PFC is enabled.
Change-ID: Ie20bd58b07608b528f3c6d95894c9ae56b00077a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
None of those drivers uses last_rx for its own needs.
See 4dc89133f4 ("net: add a comment on
netdev->last_rx") for reference.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Change-ID: Id14baae72332d0f1a9bc5d351ea1a85cb0295ec3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel has added SPEED_40000 for ethtool.
Go ahead and use the new #define.
Change-ID: Ic7e16e5c9e91085afe539f11ee1b7668adc4d0ef
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes just remove unused variables and any code that uses them
as the results of storing into these variables doesn't have any
side effects that I can see or provide any benefit.
Change-ID: I8a5ec7132ff1443d23aae729cef94beaaaf19e3a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_interrupt_scheme function had a possible failure
path to allocate memory that was found by smatch.
This adds the correct handling to the function to abort
probe if the memory allocation fails.
Change-ID: I2bf1d826a244209619da4c452d0d58b3eb5e26a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the 8 bytes of the WR_CSR_PROT field returned as part of the get
device/function capabilities AQ command.
Change-ID: Ifcaeea2ff29885fa769e4f384c7db88a25e8afd0
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a feature to enable better debugging of user reported issues by
allowing a bash script to acquire information about the internal hardware
state. The data output to the kernel log is collected by the script and can
then be sent to Intel. This is a critical debugging feature for helping us
interpret and reproduce complex customer setups.
Change-ID: Ie8b3ab09086d6870a709015f51ada05af10b41bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is to allow quick check for FCoE capability is enabled or not
in device function before any SW overrides.
Change-ID: I5f78ba798d566f143161273156916c6f4074496e
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With a HW issue that was recently discovered, after a VFLR HW might be
indicating to us a reset completion little too early. So wait another 10
msec for cache to be cleaned up.
Change-ID: I6a24dcf5dd7ffcd6500246e717411ef58532d1e9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the VF notification functions to the top of the file. This
eliminates an unnecessary declaration.
Change-ID: I036171f14180ee9f0ce4e0a21334d6a217d06c94
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Gratuitously notify VFs of link state when they activate their queues.
In general, this is the last thing that a VF driver will do as it opens
its interface, so this is a good time to notify the VF.
Currently, VF devices assume link is up unless told otherwise, which
means that VFs instantiated on a PF with no link will report the wrong
state. This change corrects that issue.
Change-ID: Iea53622904ecc681ac3f8938d81c30033ef9a0a6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this patch we can now add Flow director Sideband rules for a VF from
it's PF. Here is an example on how it can be done when VF id = 5 and
queue = 2:
"ethtool -N ethx flow-type udp4 src-ip x.x.x.x dst-ip y.y.y.y src-port p1 dst-port p2 action 2 user-def 5"
User-def specifies VF id and action specifies queue.
Change-ID: Ib37d6dff3823a4d85caffde638473891c38c2b89
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed,
the rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing
memory corruption or DMAR errors, both of which would lead to general
malaise of the kernel.
To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update i40e and i40evf to use dma_rmb. This should improve performance by
decreasing the barrier overhead on strong ordered architectures.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Change-ID: I7dc88baa33264e5919bc938adf76706573209432
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This does not affect the Virtual channel API as such but it changes the
meaning of what is communicated to the VSI resource struct as vsi_id.
Earlier vsi_idx was being passed in, which was the index in the PF's VSI
array. Now we pass vsi_id as communicated by the FW to the driver.
This will help with future expansion of VF and FW communication.
With this in place now the VF and Virtual channel driver change to move over
to VSI id use is complete and is validated.
Change-ID: I14246ef82b3b3dc1fa76291d2dd0c05d12cedb7c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: Ib98060d6352ec595ab9a78bfe252675a9fa5d8bc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VXLAN ports are added and removed, the messaging was giving some
bogus index info, the port was always '0' for the delete, and the message
text style didn't match other messages in the driver. Also, there was an
over-use of the tertiary statement which made reading a little harder
than necessary.
Change-ID: Ie805182a697b8b4c12024403ada87fd4e4fa2358
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not register or try to de-register DCB applications with the DCBNL
layer in case of NIC partitions when adapter is in MFP mode.
Change-ID: I603d042a61983a6562be471c6a2b181572504118
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If transmit VLAN HW offloads are disabled then the network stack sends up
an skb with the protocol set to 8021q. In that case to get the correct
checksum offloads we have to reset the skb protocol to the encapsulated
ethertype.
Change-ID: I903d78533de09b1c5d3ec695ee1990dd0fa5dd0d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to pci_disable_sriov got moved, but the message about not
disabling VFs didn't move. So move it. While we're at, reword the
message a bit to make it more consistent with other driver messages.
Change-ID: I17d3e15e4fcfd5c9431a96ecb0117d728d3da18b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A function was calling i40e_tx_map with return, but tx_map returns
void, and the caller returns void, so just drop the return, and
everything is good.
Change-ID: I53fc676d517864761e7cbb8ca83f1ef0c15b1f8f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the skb allocation fails we should not continue using the skb
pointer. Breaking out at the point of failure means that at the next
RX interrupt the driver will try the allocation again.
Change-ID: Iefaad69856ced7418bfd92afe55322676341f82e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several memcpys are not necessary and can be changed to structure
assignments. Struct assignments are always type safe so this
is preferable.
Change-ID: I7daf45a4b5e799c686b9d5c8ba9db047584ab82b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HMC_ERRORINFO and HMC_ERRORDATA helps explain the cause of HMC error.
Change-ID: I053bbc175a5f4c5c3e9ec2ea7400d5c56aaa4ec1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Validate that the VF has sent us a valid VSI index before actually using
that index. Without this code, a malicious or buggy VF driver could
panic the host by sending an invalid index into the VSI array.
Change-ID: I66a177687a0dcc281ec83e714d3813d70d18c8b4
Reported-by: Nick Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device appears to use a 64 bit nanoseconds register, and so with
this patch the driver should be ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances the firmware can take longer to be ready after a reset than
we're currently waiting. This patch increases the polling loop limiter to much
longer than expected.
Change-ID: I4b2c4c100dfa4abb77d02e5ecdec1cdd253b8c7e
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new devices need a new device ID some other defines to
handle the new 20G speed for KR2.
Change-ID: I03f717e364afe59657e8c9ce5ffaad856b4b21df
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting the RSS hash table and hash key through ethtool.
This patch incorporates suggestions from Ben Hutchings
<ben.hutchings@codethink.co.uk>.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump PF version to 1.2.37 and VF version to 1.2.25
Change-ID: I0287a750408250dc055c03e1f744fd5f0caefd68
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the LAN, SAN, and Port MACs for the VSI if debugfs command
dump VSI is used on the PF's VSI.
Example output:
[260221.871244] i40e 0000:04:00.0: MAC address: 68:05:ca:26:15:e0 SAN MAC: 00:00:00:00:02:00 Port MAC: 68:05:ca:26:15:e3
Change-ID: I0b393113dfb5ee7ff4f9e5227e4177885f0cc15e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code. Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVMUpdate tool doesn't necessarily know the ReadOnly map of the current
NVM image, and must try reading and writing words that may be protected.
This generates an error out of the Firmware request that the driver logs.
Unfortunately, this ends up spitting out hundreds of bogus read and write
error message that looks rather messy.
This patch checks the error type and under normal conditions will not print
the typical read and write errors during NVMUpdate. This can be overridden
by enabling the NVM update debugging. This results in a much less messy log
file, and likely many fewer customer support questions.
Change-ID: Id4ff2e9048c523b0ff503aa5ab181b025ec948ea
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.
The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.
Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the sizeof() calls are taking the size of the actual struct
that we care about. By using the pointer variable, we'll always get
the right struct size, even if the variable type changes sometime in
the future.
Change-ID: Id5858f883cf42447365ea3733080d7714f975bce
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While using the Linux "strings" command I found these two strings in the
driver. There's no need for them and they're kinda silly.
Change-ID: I4e19b02983d48b631e9a9979f49790492845f221
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of configfs is not allowed in network drivers. Strip the code that
uses it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.12 and i40evf to 1.2.6.
Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.
Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.
Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use l4_tunnel type generically to keep code flow simple.
Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.
If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.
If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.
ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.
Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is not necessary to print FD filter add/delete log with
normal debug settings because ethtool -n ethx shows all the FD-SB
filters on an interface. The log can still be turned on through higher
debug levels and it will continue to print a log if there was an error
in the add/delete process.
Change-ID: I67db2baf49e2075d2f537de40f7895e5b02cd610
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only print the port and veb stats if this is the first partition
of a multiplexed port.
Change-ID: I7ce0c323cdee5cfd2e54d8bea5b0b9102987e671
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.
Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition. This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny. Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.
Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.
Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were some additional spaces and strange (double swapping) logic
in this function that I started looking at because sparse was warning.
This fixes the sparse warning and fixes up the other issues.
Change-ID: I72a91a4197cd45921602649040e6bd25e5f17c0a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel returns a u32 for netif_msg_init, and we were storing
it in a u16. Fix the width of the datatype.
Change-ID: I4b23326e5707c91cd59325c5a1ccb2ba7a3974fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove LE16 to CPU endianes conversion from i40e_read_nvm_word_srctl
function, as it's already done by register read function.
Change-ID: I739f0f20a9b8e18223e54c0ca5443e63d75da878
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This series of code was repeated twice, remove one of them.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.
Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.
Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As pointed out by Ben Hutchings, ioremap uses unsigned long as
its parameter type, so we should be using that instead of u32
or int.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.11 and i40evf to 1.2.5
Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver spams the system log with messages about VF VSI when VFs
are created, as well as each time they are reset. This is annoying, and
the information isn't even useful most of the time.
Remove this message to reduce user annoyance.
Change-ID: I8de90d05380f54b038c9c8c3265150be87c9242c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IRQ tracking setup and teardown into the same routines that
do the IRQ setup and teardown. This keeps like activities together and
allows us to track exactly the number of vectors reserved from the OS,
which may be fewer than are available from the HW.
Change-ID: I6b2b1a955c5f0ac6b94c3084304ed0b2ea6777cf
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For future device support we do not want to map the whole CSR space since some
of it is mapped by other drivers with different mapping methods.
Note: As a side effect, the flash region (if exposed through the memory map)
gets unmapped too since it follows the future use region.
Change-ID: Ic729a2eacd692984220b1a415ff4fa0f98ea419a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.
Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the 10G and 40G AOC PHY types to the case statement in get_media_type
and ethtool get_settings so that the correct information gets reported
back to the user.
Change-ID: I1b4849d22199a9acf7c8807166d0317c1faad375
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the system administrator is requesting an offline diagnostic test using
'ethtool -t' then we should, you know, actually take the device offline
before doing the testing.
Change-ID: I6afa1cbfcc821c9ab6e6f47ed4d8dc2d8dd20e82
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some FW versions are incorrectly reporting a breakout cable as PHY type
0x3 when it should be 0x16 (I40E_PHY_TYPE_10GBASE_SFPP_CU).
If we get this value back from FW and the version is < 4.40, reassign it
to I40E_PHY_TYPE_10GBASE_SFPP_CU.
Change-ID: Ibb41a0e3cd2c0753744e8553959240df6ed13ae8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During resets (possibly caused by a Tx hang) the driver would
accidentally clear the XPS mask for all queues back to 0.
This caused higher CPU utilization and had some other performance impacts
for transmit tests.
Change-ID: I95f112432c9e643a153eaa31cd28cdcbfdd01831
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use automatic sign extension by replacing 0xffff... constants
with ~(u64)0 or ~(u32)0.
Change-ID: I73cab4cd2611795bb12e00f0f24fafaaee07457c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
0x2A is the NVM version so it has useful data but it is per image
version every image can have a different one. 0x18 is the dev starter
version which all the images for release will have the same version.
Of the two 0x18 is more useful and is what should be displayed.
Change-ID: Idf493da13a42ab211e2de0bef287f5de51033cca
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In CEE mode the firmware does not set the operational status bit of
the application TLV status as returned from the "Get CEE DCBX Oper Cfg"
AQ command. This occurs whenever a DCBX configuration is changed.
This is a workaround to remove the check for the operational and sync bits
of the application TLV status till a firmware fix is provided.
Change-ID: I1a31ff2fcadcb06feb5b55776a33593afc6ea176
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify our get and set LED functions so they ignore activity LEDs,
as we are required to blink the link LEDs only.
Change-ID: I647ea67a6fc95cbbab6e3cd01d81ec9ae096a9ad
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to the driver initialization have caused the BW
configurations to not take effect. We use a BW configuration read and
write back to "kick" the Tx scheduler into action.
Change-ID: I94ab377c58d3a3986e3de62b6c199be3fd2ee5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-03-03
This series contains updates to fm10k, i40e and i40evf.
Matthew updates the fm10k driver by cleaning up code comments and whitespace
issues. Also modifies the tunnel length header check, to make it more robust
by calculating the inner L4 header length based on whether it is TCP or UDP.
Implemented ndo_features_check() that allows drivers to report their offload
capabilities per-skb.
Neerav updates the i40e driver to skip over priority tagging if DCB is not
enabled. Fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local DCBX
application configuration TLVs. Fixed i40e where, in the case of MFP
mode, the driver was returning the incorrect number of traffic classes
for partitions that are not enabled for iSCSI. Even though the driver
was not configuring these traffic classes in the transmit scheduler for
the NIC partitions, it does use this map to setup the queue mappings.
Shannon updates i40e/i40evf to include the firmware build number in the
formatted firmware version string.
Akeem adds a safety net (by adding a 'default' case) for the possible
unmatched switch calls.
Mitch updates i40e to not automatically disable PF loopback at runtime,
now that we have the functionality to enable and disable PF loopback. This
fix cleans up a bogus error message when removing the PF module with VFs
enabled. Adds a extra check to make sure that the indirection table
pointer is valid before dereferencing it.
Anjali enables i40e to enable more than the max RSS qps when running in a
single TC mode for the main VSI. It is possible to enable as many as
num_online_cpus(). Adds a firmware check to ensure that DCB is disabled for
firmware versions older than 4.33. Updates i40e/i40evf to add missing
packet types for VXLAN offload. Updated i40e to be able to handle varying
RSS table size for each VSI, since all VSI's do not have the same RSS table
size.
v2: Dropped previous patch #9 "i40e/i40evf: Add capability to gather VEB
per TC stats" since the stats should be in ethtool and not debugfs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Module dependencies are broken in the case where CONFIG_I40E=y and
CONFIG_CONFIGFS_FS=m. This fixes the broken dependency.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.
This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.
Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow DCBNL operations in MFP mode to allow query of port DCB settings
via all the PFs and register iSCSI APP on iSCSI enabled PF.
Change-ID: I34cc39b4665d0a631847d4079350d3814f02381e
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.
Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.
Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size
Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were missing a few packet types for VXLAN offload. This patch fixes
that.
Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.
Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.
Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This patch makes it possible to
enable as many as num_online_cpus().
ethtool -L can still be used to reconfigure number of qps
to a smaller value.
Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now have functionality to enable and disable PF loopback at
runtime, don't try to do it automatically. Removing this call also gets
rid of a bogus error message when removing the PF module with VFs
enabled.
Change-ID: Ic38652d8a3b9498d96113bfaa5ea7bad050862e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds default case to handle unmatched switch calls.
Change-ID: Icd203570a1dc5322c1038f68b98a83195e8ad28c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include the FW build number in the formatted FW version string. In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version. This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.
Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If DCB is not enabled priority tagging is not needed
so skip over that section.
Change-ID: Ia3f3fa07945b421259a9ca38329d6d1cbd6c6bcc
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we don't try to dereference NULL pointers when returning values
from the AdminQ calls.
Change-ID: Ia6694f2f415d50acf0aba063c863568742799aff
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, a multi-write transaction takes longer than the
default 3 minute timeout on the write semaphore. If the write failed with
an EBUSY status, this is likely the problem, so here we try to reacquire
the semaphore then retry the write. We only do one retry, then give up.
Change-ID: I1c8be60688acc2f39573839579baf601207c4a36
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine the ICR0 shutdown with the standard interrupt shutdown, and
add the interrupt clearing to the PCI shutdown path.
This prevents the driver from allowing stray interrupts or causing
system logs from un-handled interrupts.
Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of DCB reconfiguration flow if the Tx queue disable times out
then issue a PF reset to do some level of recovery.
Change-ID: I7550021c55bff355351c0365e61e1f05fcaff46d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB is reconfigured to single TC the driver did not reset the
Tx ring Qset handle to the correct mapping; which caused Tx queue
disable timeouts.
Change-ID: I4da5915ec92a83c281b478d653fae6ef1b72edfe
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver or hardware gets less interrupt vectors than the actual
number of CPU cores, limit the queue count for the priority queue
traffic class (TC) queues.
This will fix a warning with multiple function mode where systems
regularly have more cores than vectors.
Also add extra comment for readability.
Change-ID: I4f02226263aa3995e1f5ee5503eac0cd6ee12fbd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was having some issues with false Tx hang detection. This
makes the driver a little more direct with the checks for progress
forward by directly checking the head write back address and tail register
when determining progress. This avoids Tx hangs where the software
gets behind, because we are directly checking hardware state when
determining hang state.
Change-ID: I774f0e861c9e8ab5ccb213634100fe15440ae24a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware has some limitations the driver needs to adhere to,
that we found in extended testing.
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events occurs, the hardware will generate an internal
error and freeze the Tx queue.
This patch linearizes the skb to avoid these situations.
Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds check to bail out if device is already down when checking
for Tx hang subtask.
Change-ID: I3853fb7a6d11cb9a4c349b687cb25c15b19977a0
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parens to make sure the shift and bitwise precedences don't work backwards
for us.
Change-ID: I60c10ef4fad6bc654522b9d8a53da2e270a0f268
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a leak of 'cmd_buf' when copy_from_user() failed
in i40e_dbg_command_write().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow an application to query the i40e driver's private flags to get the
status of NPAR enablement. This will be used by applications to determine
if there are NPAR specific features available.
Change-ID: Ia6d9477a48f9c4cb41ca022bd433f77da3f2146c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set FLAG_RD for send_driver_version AQ command.
Change-ID: I8253051eff85a1d4b5a4e12ce0395b65ceb91e62
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the RX routine in use to the features log message.
Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setup FCoE netdev device type as "fcoe", so that it shows up in
sysfs as FCoE device.
Change-ID: Ie13a1a332dba4d5802586926104ee01ef20da44f
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BUF flag must be set for indirect AQ command.
Change-ID: I6819718a47baf69d1a91ebaed89f735ed6e86025
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.
By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.
The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.
In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.
Also update the copyright year.
Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add configfs controls to get, set and commit NPAR BW configurations.
We export three controls:
min_bw - Can take a value from 0 to 100 inclusive
max_bw - Can take a value from 1 to 100 inclusive
commit - A write-only control that accepts only a value of 1 and will
cause the BW settings to be permanently committed to NVM so
that they are persistent across power cycles and system
resets
The BW values are relative and are expressed as percentages. For more
information on the interpretation of the BW settings see the Dell
specifications for NPAR.
Also update the copyright year.
Change-ID: Id7496ca65630b5037e32ba6a5a748fbc1632881b
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to be able to get, set and commit permanently the NPAR
partition BW configuration through configfs. These are necessary
precursor functions for that feature.
Also update the copyright year.
Change-ID: I9d5ca160a9288145f1dd2042994028679fff55f3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an IOMMU is in use, the packet split receive path shows a distinct
advantage over the single-buffer path because it minimizes DMA mapping
and unmapping. However, this is not an advantage for systems with no
IOMMU. At init time, check to see if an IOMMU is enabled and enable
packet split receives.
Change-ID: I4f70d2e9c31bbea3dc8fd0c5734959a6e6602210
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a struct to the VSI struct to keep track of rxnfc
settings done via ethtool. Without this patch, the device can only
list the options available, not the current settings and this is not
clear to the user. Without current settings, the available settings
never changing looks like a bug.
Also update the copyright year.
Change-ID: I087bbfdb33b330496a671630a7586773e3b3e589
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).
Use the advertised speed settings in get_settings in ethtool now that
we have it. Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.
To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.
Also update the copyright year.
Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_debug_aq() prints information helpful in debugging
admin queue commands, but it doesn't do so correctly on big endian machines.
This patch adds the appropriate LExx_TO_CPU wrappers for big endian
architectures.
Also update the copyright year.
Change-ID: I4b2dc229ed5bf6dfe35632a58cddf53c21aff4b0
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netdev op that allows the operator to turn MAC/VLAN spoof checking on
and off did not include the flag for VLAN spoof checking. This patch
fixes that problem.
Change-ID: Ib4c9e639024a854592d97af22706544881ac3fcb
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.8 and i40evf to 1.2.2
Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An_enable was never used only set so lets remove it. The function
update_link_info only did two things, call get_link_info and set
an_enabled. Therefore we should also remove update_link_info and
change all references to it to get_link_info.
Change-ID: Ie3022680fa7a94bfd495a4f5fc76a73701d85569
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't trigger another EMPR when we receive an EMPR event.
This patch handles EMPR event reception with a different state
so that we can do the right thing for NVM.
Change-ID: I9cac70b3658600f016a65beb6fb157e1c1f9adf9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some registers have been removed so take them out and
stop updating and looking at them.
Change-ID: I33da922c8de993a94dd8b8d8a2ae2146b8ca1a27
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use #defined VSI connection type values instead of using magic numbers.
Change-ID: I2f6cf7bf394d391e1c0fe61779e9e4ad8858154a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until the time a more robust versioning scheme is needed/implemented all
established virtual channel opcode values should remain consistent between
updates to the opcode enum.
This patch repositions I40E_VIRTCHNL_OP_CONFIG_RSS to the end of the enum. In
its current position this opcode displaces the initial value of
I40E_VIRTCHNL_OP_EVENT and will cause PF/VF compatibility issues.
Going forward the expectation is either:
a) All future opcode additions will be added as the last element of the
enum. Once VF drivers start making use of the new commands the virtual
channel version will need to be incremented and drivers will need to
implement a simple version check whereby VF drivers can only load on
PFs with a >= version.
b) or, if needed, design and implement a more complicated API
negotiation capability.
In either case PF drivers should always maintain backwards compatibility with
earlier VF driver versions.
Change-ID: Ie245daa09a231b6680ed793d648bdcc76caefe58
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change debugfs command from "clear_stats pf" to "clear_stats port"
to be clearer what the action is. Also, limit the action to the
base PF, not the NPAR partitions.
Change-ID: I22aa39c0962d83a83a985097b1000ed7f8c66f3f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is to refactor the read/write functions to support
future work.
Change-ID: I13150d5e3042f2c617362c0140dc7e6473ebcdee
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes indentation issue and error found in argument
reported by static analysis. Without this patch, sparse and other
static analysis errors will be found.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to u64_stats_init to Rx setup.
This done in order to avoid lockdep errors with seqcount on newer kernels.
Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For all VSIs on a VEB, Loopback mode should be either on or off.
Our configuration requires them to be ON so that VSIs can directly
talk to each other without going out on the wire.
Change-ID: I77b8310bc846329972b13b185949ab1431a46c30
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set different dev_port value 1 for FCoE netdev than the default zero
dev_port value for PF netdev, this helps biosdevname user tool to
differentiate them correctly while both attached to the same PCI
function.
Change-ID: I8fb90e4ef52a1242f7580e49a3f0918735aee8ef
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure to clear the GPIO blink field, instead of OR'ing against zero
if the field is already '1'.
Change-ID: Ie52a52abd48f6f52b20778a6b8b0c542dfc9245c
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch forces Tx descriptor writebacks on ITR by kicking
off the SWINT interrupt when we notice that there are non-cache-aligned
Tx descriptors waiting in the ring while interrupts are disabled
under NAPI.
Change-ID: dd6d9675629bf266c7515ad7a201394618c35444
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the service task in the shutdown handler, preventing it from
accessing the admin queue after it had been closed. This fixes a panic
that could occur when the system was shut down with a lot of VFs
enabled.
Change-ID: I286735e3842de472385bbf7ad68d30331e508add
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During VF deallocation, we need to lock out the VF reset code. However,
we cannot depend on simply masking the interrupt, as this does not lock
out the service task, which can still call the reset routine. Instead,
leave the interrupt enabled, but add locking around the VF disable and
reset routines.
For the disable code, we wait to get the lock, as the reset code will
take a finite amount of time to run. For the reset code, we just return
if we fail to get the lock. Since we know that the VFs are being
disabled, we don't need to handle the reset.
This fixes a panic when disabling SR-IOV.
Change-ID: Iea0a6cdef35c331f48c6d5b2f8e6f0e86322e7d8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling 64 VFs and loading the VF driver in the host kernel, we
can easily overrun the PF's admin receive queue. Double the size of this
queue, and increase the work limit to allow the PF to handle more
requests in a single pass through the service task.
Change-ID: I0efbbdc61954bffad422a2f33c4b948a59370bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delay a minimum of 10ms after VF reset, to allow the hardware's internal
FIFOs to flush.
Change-ID: I8a02ddb28c9f0d7303a1eb21d0b2443e5b4c1cda
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later. This patch just
reorders the code hunks in what I believe was the intended sequence.
Coverity: CID 1260099
Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function i40e_rx_is_fip() that is not used anywhere.
This was partially found by using a static code analysis program
called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.6 and i40evf to 1.2.0 version.
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.
Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.
Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up NVM config read and write data structs.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.
Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.
Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.
Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.
Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.5 and i40evf to 1.0.7.
Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dump Stats string has been removed from functional debugfs
help message. Now it does not show up when we echo command to
debugfs/Fortville queue.
Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch creates a define for interrupt name string configuration that
is large enough to contain full bus/slot info, rather than just netdev->name.
Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup. Also adjust the log strings
a little to look less scary.
Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names
Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase ASQ timeout for some scenarios with multi-function devices
Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several little tweaks to keep FW, SV, and SW in line together
- Remove the unused and deprecated
i40e_aqc_opc_debug_modify_internals
- Add define for iSCSI capability
- Fix queue mask size
- Adjust i40e_aqc_oem_param_change for ease-of-use
Change-ID: I51f250b367912968a7cec61b3a68110d9796e914
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kamil Kacperski <kamil.kacperski@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we only allow SR/IOV on the master PF of a port in multifunction
mode. This should be the case anyway based on the num_vfs configured in
the NVM, but this will help make sure there's no question. If we're not
in multifunction mode the partition_id will always be 1.
Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were only checking if the link up state had changed,
and if it hadn't exiting the link event routine early. We should
also check if speed has changed, and if it has, stay and finish
processing the link event.
Change-ID: I9c8e0991b3f0279108a7858898c3c5ce0a9856b8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in multi-function mode, e.g. Dell's NPAR, only partition 1
of each MAC is allowed to set WoL, speed, and flow control.
Change-ID: I87a9debc7479361c55a71f0120294ea319f23588
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function will read PBA Block from Shadow RAM and return it in a string format.
Change-ID: I4ee7059f6e21bd0eba38687da15e772e0b4ab36e
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in NPAR mode the driver instance might be controlling the base
partition or one of the other "fake" PFs. There are some things that
can only be done by the base partition, aka partition_id 1. This code
does a bit of work to find how many partitions are there per port and
what is the current partition_id.
Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These mac address already added by FCoE stack above netdev,
therefore adding them here is redundant.
Change-ID: Ia5b59f426f57efd20f8945f7c6cc5d741fbe06e5
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NPAR enabled partitions should warn the user when detected link speed is
less than 10Gpbs.
Change-ID: I7728bb8ce279bf0f4f755d78d7071074a4eb5f69
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If VF drivers are loaded in the host OS, the call to pci_disable_sriov()
will cause these drivers' remove routines to be called. If the PF driver
has already freed VF resources before this happens, then the VF remove
routine can't properly communicate with the PF driver causing all sorts
of mayhem and error messages and hurt feelings.
To fix this, we move the call to pci_disable_sriov() up to the top of
the function and let it complete before freeing any VF resources.
Change-ID: I397c3997a00f6408e32b7735273911e499600236
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was examining the outer protocol layer to set the inner protocol
layer checksum offload. In the case of TCP over IPV6 over an IPv4 based
VXLAN the inner checksum offloads would be set to look for IPv4/UDP instead
of IPv6/TCP. This code fixes that so that the driver will look at the
proper layer for encapsulation offload settings.
Signed-off-by: Anjali Singhai <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Rx port checksum error counter was incrementing incorrectly with
UDP encapsulated tunneled traffic. This patch fixes the problem so that
the port_rx_csum counter will show accurate statistics.
Signed-off-by: Anjali Singhai <anjali.singhai@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver was polling with interrupts disabled the hardware
will occasionally not write back descriptors. This patch causes
the driver to detect this situation and force an interrupt to
fire which will flush the stuck descriptor. Does not conflict
with napi because if we are already polling the napi_schedule is
ignored. Additionally the extra interrupts are rate limited, so
don't cause a burden to the CPU.
Change-ID: Iba4616d2a71288672a5f08e4512e2704b97335e8
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.
Fixes:
> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.
Fixes: f6f6424ba7 ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline functions are preferred over macros when they can be used
interchangeably.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a little more state context to an NVM update debug message.
Change-ID: I512160259052bcdbe5bdf1adf403ab2bf7984970
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set. This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.
Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only poll on the NVM semaphore if there's time left on a previous
reservation. Also, add a little more info to debug messages.
Change-ID: I2439bf870b95a28b810dcb5cca1c06440463cf8a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The state transitions after an error were not managed well, so
these changes get us back to the INIT state or don't transition
out of the INIT state after most errors.
Change-ID: I90aa0e4e348dc4f58cbcdce9c5d4b7fd35981c6c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit. Also,
rename a variable for clarity and fix a comment.
Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The nvm_semaphore_wait field is set but never used, so let's
just get rid of it.
Change-ID: I2107bd29b69f99b1a61d7591d087429527c9d8fa
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adminq init is run after the EMPR that is triggered by the
NVM update. The final write command will cause the reset and
will want to wait for the ARQ event that signals the end of the
update, but the reset precludes the event being sent. The state
is probably already at INIT, but we set it so here anyway, and
clear the release_on_done flag as well.
Change-ID: Ie9d724a39e71f988741abc3d51b4cb198c7e0272
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just to be sure, add a range check to avoid any possible
array index-out-of-bound issues.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Change-ID: I9323bee6732c2a47599816e1d6c6b3a1f8dcbf54
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rework the debug messages in the NVM update state machine so that we can
turn them on and off dynamically rather than forcing a recompile/reload.
These can now be turned on with something like:
ethtool -s eth1 msglvl 0xf000008f
and off with:
ethtool -s eth1 msglvl 0xf000000f
The high 0xf0000000 gets the driver's attention that we want to change the
internal debug flags, and the 0x80 bit is the NVM debug.
Change-ID: I5efb9039400304b29a0fd6ddea3f47bb362e6661
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM update operations take time finish asynchronously, and follow-on
update requests need to wait for the current one to finish. Early
firmware didn't handle this well, so the code had to track the busy state.
The released firmware handles the busy state correctly, returning
I40E_AQ_RC_EBUSY if an update is still in progress, so the code no longer
needs to track this.
Change-ID: I6e6b4adc26d6dcc5fd7adfee5763423858a7d921
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add more detail to the NVM update error messages so folks
have a better chance at diagnosing issues without having to
resort to heroic measures to reproduce an issue.
Change-ID: I270d1a9c903baceaef0bebcc55d29108ac08b0bd
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once in a great while the NVMUpdate tools and the driver get out
of phase with each other. This gives us a way to reset things
without having to unload the driver.
Change-ID: I353f688236249a666a90ba3e7233e0ed8c1a04e9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-06
This series contains updates to i40e and i40evf.
Shannon provides several patches to cleanup and fix i40e. First removes
an unneeded break statement in i40e_vsi_link_event(). Then removes
some debug messages that really do not give any useful information and
ends up getting printed every service_task loop, which fills the logfile
with noise when AQ tracing is enabled. Updates the aq_cmd arguments to
use %i which is much more forgiving and user friendly than the more
restrictive %x, or %d. Fixes the netdev_stat macro, where the old
xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated.
Getting the pf_id from the function number had an issue when
when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number.
Carolyn adds additional text description for the base pf0 and flow
director generated interrupts, since these interrupts are difficult
to distinguish per port on a multi-function device.
Jacob resolves an issue related to images with multiple PFs per
physical port. We cannot fully support 1588 PTP features, since only
one port should control (i.e. write) the registers at a time. Doing
so can cause interference of functionality.
Anjali provides several updates to i40e, first adds the Virtual Channel
OP event opcode for CONFIG_RSS, so that the Virtual Channel state
machine can properly decipher status change events. Then updates the
driver to add (and use) i40e_is_vf macro for future expansion when new
VF MAC types get added. Adds new update VSI flow to accommodate a
firmware dix with VSI loopback mode. All VSIs on a VEB should either
have loopback enabled or disabled, a mixed mode is not supported for a
VEB. Since our driver supports multiple VSIs per PF that need to talk to
each other make sure to enable Loopback for the PF and FDIR VSI as well.
Mitch provides a couple of i40e and i40evf patches. First updates
i40evf init code more adept at handling when multiple VFs attempt
to initialize simultaneously.
Joe Perches provides a i40e patch which resolves a compile warning
about about frame size being larger than 2048 bytes by reducing the
stack use by using kmemdup and not using a very large struct on the
stack.
v2:
- Dropped patch 13 & 14 while Mitch reworks the patches based on
feedback from Ben Hutchings, probably the tryptophan in the turkey
is to blame for the delay...
- Added Joe Perches patch which resolves a compile warning about frame
size
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce stack use by using kmemdup and not using a very
large struct on stack.
In function ‘i40e_dbg_dump_desc’:
warning: the frame size of 8192 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Getting the pf_id from the function number was a good place to start,
but when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number. This works in NPAR mode as well.
Change-ID: I65e3dd6c97594890c2bad566b83cc670b1dae534
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ARQ needs to have at least as many entries as VFs, or the VFs will
get errors from the FW when they send messages to the PF. Since we don't
know how many VFs we'll end up with, just set up 128 descriptors.
Change-ID: I04ae3d1c7faf09110eb782214e9c05aeb62a6c59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an order in which this should happen. It turns out that FW will
not let you change the Loopback setting of the VSI with update VSI prior
to the VEB creation.
Change-ID: I7614ddff8b4c37702930c02f16f8c346aaa64bd1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All VSIs on a VEB should either have loopback enabled or disabled, a
mixed mode is not supported for a VEB. Since our driver supports multiple
VSIs per PF that need to talk to each other make sure to enable Loopback
for the PF and FDIR VSI as well.
Also, we now have to explicitly enable Loopback mode otherwise we fail
VSI creation for VMDq and VF VSIs.
Change-ID: Ib68c3ea4aeb730ac9468f930610de456efbe5b20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase reset delay to ensure all internal caches are properly flushed
in worst case scenario.
Change-ID: I6f059a9e024fbf9ef1debd32497eed21369957fc
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated. Since we're
using rtnl_link_stats64 in other parts of the driver, we should use it
here as well. We've just been lucky that the field definitions are the
same sizes.
Change-ID: I19fc71619905700235dcdf0d3c8153aec81d36de
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.
Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.
Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve an issue related to images with multiple PFs per physical
port. We cannot fully support 1588 PTP features, since only one port
should control (ie: write) the registers at a time. Doing so can cause
interference of functionality.
It may be possible to partially implement the API for only those
features without side effects. However, this at minimum means non
controlling PFs lose Tx timestamps, frequency atunement, and possibly
SYSTIME adjustment. There may be further impact I did not discover.
Since the API in the kernel expects these features to work, it is
simpler and less dangerous to just disable PTP features on all PFs not
identified as the controlling PF in PRTTSYN_CTL0.PF_ID.
This change also removes the warning printed when hwtstaml IOCTL is
called on the wrong PF. This is actually meaningless now, since only one
PF per port will support it. In addition, the ethtool get_ts_info IOCTL
was updated so that only the controlling port will even indicate support
(so as not to confuse users).
The overall downside is complete loss of functionality on non
controlling PF, vs the possible gain of partial support. The biggest
factor for choosing this approach is simplicity and ensuring that the
main PF will work. There could easily be other portions of the 1588
logic with side effects I am not aware, and the reduced functionality
that might be made available is significantly less useful. In addition,
the API does not allow for proper indication of why particular features
are not supported. These reasons are enough to decide for the simpler
approach to resolving this issue.
Change-ID: If4696bae686fc18aef6552b67dd417213d987c16
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds additional text description for base pf0 and flow director
generated interrupts. Without this patch, these interrupts are difficult
to distinguish per port on a multi-function device.
Change-ID: I4662e1b38840757765a3fe63d90219d28e76bfab
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the 'i' rather than the more restrictive 'x' or 'd' in the aq_cmd
arguments. This makes the user interface much more forgiving and user
friendly.
Change-ID: I5dcd57b9befc047e06b74cf1152a25a3fa9e1309
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled. This patch simply removes
the noise.
Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This case statement is empty and the fall through just breaks out
so remove the break and let it fall through to break out.
Change-ID: I1b5ba9870d5245ca80bfca6e7f5f089e2eb8ccb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original FDB code submission wasn't correct and the code
wasn't enabled. This removes some dead code (can use the common kernel
code for fdb_del and fdb_dump) and correctly enables the fdb_add
function pointer.
The fdb_add functionality is important to i40e because it is needed
for a workaround to allow bridges to work correctly on the i40e
hardware.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we want the SW INT to go off as soon as possible, write the
extra bits that will turn off the ITR wait for the interrupt.
Change-ID: I6d5382ba60840fa32abb7dea17c839eb4b5f68f7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Overloading the msg_size field in the arq_event_info struct is just a
bad idea. It leads to repeated bugs when the structure is used in a
loop, since the input value (buffer size) is overwritten by the output
value (actual message length).
Fix this by splitting the field into two and renaming to indicate the
actual function of each field.
Since the arq_event struct has now changed, we need to change the drivers
to support this. Note that we no longer need to initialize the buffer size
each time we go through a loop as this value is no longer destroyed by
arq processing.
In the process, we also fix a bug in i40evf_verify_api_ver where the
buffer size was not correctly reinitialized each time through the loop.
Change-ID: Ic7f9633cdd6f871f93e698dfb095e29c696f5581
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.
This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.
Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PFC is enabled we should not proceed with setting the link flow control
parameters. Also, always report the link flow Tx/Rx settings as off when
PFC is enabled.
Change-ID: Ib09ec58afdf0b2e587ac9d8851a5c80ad58206c4
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FCoE VSI Tx queue disable times out when reconfiguring as a result of
DCB TC configuration change event.
The hardware allows us to skip disabling and enabling of Tx queues for
VSIs with single TC enabled. As FCoE VSI is configured to have only
single TC we skip it from disable/enable flow.
Change-ID: Ia73ff3df8785ba2aa3db91e6f2c9005e61ebaec2
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB TC configuration changes the firmware suspends the port's Tx.
Now, as DCB TCs may have changed the PF driver tries to reconfigure the
TC configuration of the VSIs it manages. As part of this process it disables
the VSI queues but the Tx queue disable will not complete as the port's
Tx has been suspended. So, waiting for Tx queues to go to disable state
in this flow may lead to detection of Tx queue disable timeout errors.
Hence, this patch adds a new PF state so that if a port's Tx is in
suspended state the Tx queue disable flow would just put the request for
the queue to be disabled and return without waiting for the queue to be
actually disabled.
Once the VSI(s) TC reconfiguration has been done and driver has called
firmware AQC "Resume PF Traffic" the driver checks the Tx queues requested
to be disabled are actually disabled before re-enabling them again.
Change-ID: If3e03ce4813a4e342dbd5a1eb1d2861e952b7544
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the port TC configuration changes as a result of DCBx the driver
modifies the enabled TCs for the VEBs it manages. But, in the process
it did not update the enabled_tc value that it caches on a per VEB basis.
So, when the next reconfiguration event occurs where the number of TC
value is same as the value cached in enabled_tc for a given VEB; driver
does not modify it's TC configuration by calling appropriate AQ command
believing it is running with the same configuration as requested.
Now, as the VEB is not actually enabled for the TCs that are there any
TC configuration command for VSI attached to that VEB with TCs that are
not enabled for the VEB fails.
This patch fixes this issue.
Change-ID: Ife5694469b05494228e0d850429ea1734738cf29
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check whether LLDP Agent's default AdminStatus is
enabled or disabled on a given port. If it is disabled then it sets
the DCBX status to disabled as well; and would not query firmware for
any DCBX configuration data.
Change-ID: I73c0b9f0adbf4cae177d14914b20a48c9a8f50fd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.
Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.
This patch adds this call to the flow that handles DCB re-configuration in
the PF.
Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bumping minor version as this will be the second SW release and it
should be 1.
Change-ID: If0bd102095d2f059ae0c9b7f4ad625535ffbbdee
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF interrupt processing takes a looooong time, and it's possible that we
could lose a VFLR event if it happens while we're processing a VFLR on
another VF. This would leave the VF in a semi-permanent reset state,
which would not be cleared until yet another VF experiences a VFLR.
To correct this situation, we enable the VFLR interrupt cause before we
begin processing any pending resets. This means that any VFLR that
occurs during reset processing will generate another interrupt and this
routine will get called again.
This change may cause a spurious interrupt when multiple VFLRs occur
very close together in time. If this happens, then this routine will be
called again and it will detect no outstanding VFLR events and do
nothing. No harm, no foul.
Change-ID: Id0451f3e6e73a2cf6db1668296c71e129b59dc19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only warn once that PTP is not supported when linked at 100Mbit.
Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports. That should be plenty.
Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt throttle rate minimum is actually 2us, so
fix that define and while we are there, remove some unused defines.
Change some strings in the function to be a bit less wrappy, and
express the correct limits.
Change-ID: I96829bbc77935e0b57c6f0fc1439fb4152b2960a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ARQ events cause a service_task execution, and we do a link_status
check and full stats gathering for each service_task. However, when
there are a lot of ARQ events, such as when doing an NVM update, we end up
doing 10's if not 100's of these per second, thereby heavily abusing the
PCI bus and especially the Firmware. This patch adds a check to keep the
service_task from running these periodic tasks more than once per second,
while still allowing quick action to service the events.
Change-ID: Iec7670c37bfae9791c43fec26df48aea7f70b33e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code was polling the firmware tail register for completion every
10 microseconds, which is way faster than the firmware can respond.
This changes the poll interval to 1ms, which reduces polling CPU
utilization, and the number of times we loop.
The maximum delay is still 100ms.
Change-ID: I4bbfa6b66d802890baf8b4154061e55942b90958
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a few problems with our parsing of the MDET registers:
* Queue IDs are longer than 8 bits
* Queue IDs are absolute for the device and the base queue must be
subtracted out.
* VF IDs are longer than 8 bits
* Use the MASK define to mask the event value, instead of the SHIFT
define.
Change-ID: I3dc7237f480c02e1192a2a8ea782f8a02ab2a8b7
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We must insert the VSI ID in the QTX_CTL register when
configuring queues for VMDQ VSIs.
Change-ID: Iedfe36bd42ca0adc90a7cc2b7cf04795a98f4761
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check the debug module parameter earlier to be able to catch the early
configuration phase adminq messages.
Change-ID: Ic84fabd72393489bbf96042de770790a80fd8468
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tweak and homogenize the error reporting for get_lump() resource
tracking errors.
Change-ID: I11330161cc6ad8d04371c499c63071c816171c3b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are more cores than vectors available to the PF, scale back
the LAN msix usage to force queue/vector sharing and leave some vectors
for Flow Director, VMDq, etc.
Change-ID: Ie0317732eb85ad8d851d7da7d9af86b1bf8c21ad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugfs dump stats wasn't being kept up-to-date, was redundant with
the ethtool output, and didn't offer any useful additional info. Rather
than continue trying to keep them aligned, just remove the debugfs command.
Change-ID: Id130ed9aef01c6369ab662c7b4c5ec5b1dbc5b40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <Jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to irq_dynamic_disable was turning off the interrupt completely
when trying to set ITR to 0 (for lowest moderation). Just remove the
call as setting the values to 0 later in this function will suffice.
Change-ID: I47caf1ecbe65653cf63ec833db93094cd83fd84d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.
Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.
Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When FD_SB/ATR are not enabled, do not allow flow director flush
and reinit.
Change-ID: Iafe261c1862992981615815551abd1ed9fada0a8
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We accidentally mask by the _SHIFT variable. It means that "event" is
always zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e version to 1.0.21.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the three variables out of the loop, so it only declares once.
Change-ID: I436913777c7da3c16dc0031b59e3ffa61de74718
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add driver support for 10GBaseT device.
Change-ID: I4be6ed847ac0bddd220b9878a95c523b32038174
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to handle link events when updating the PF switch. This
allows link information to be properly provided to VFs in all cases.
Change-ID: If314c95f3d39259ef4c40a4a3b823381e28fb24f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the setting of flow control because this should be done at a pf level not
a vsi level. Also add a sleep and restart an to fix a bug where Rx would stop
after some stress.
Change-ID: I9a93d8c2ff27c39339eb00bc4ec1225e43900be0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the Documentation/timers/timers-howto.txt it is preferred to use
usleep_range() instead of udelay() if the delay value is > 10us in
non-atomic contexts.
So, replacing all the instances of udelay() with 10 or greater than 10
micro seconds delay in the driver and using usleep_range() instead.
Change-ID: Iaa2ab499a4c26f6005e5d86cc421407ef9de16c7
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is one small step in making the indentation more consistent. If
we truly want to align values, then use tabs rather than spaces.
Change-ID: I12368bc77a52f296d1843fdcb67201a7d7cd4749
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
The driver can do a simpler job of managing link state by simply
using the admin queue receive event for link events as a doorbell
that tells the driver to update link state.
Additionally, add a workaround will help make sure the link state in the
hardware is consistent with the link state the driver is reporting
by refreshing the link state every service task interval.
Change-ID: Ib95b5b7b8cc016e97d8009f6363c9f9eed301444
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tell the firmware what kind of link related events the driver is
interested in. In this case, just link up/down and qualified module
events are the ones the driver really cares about.
Change-ID: If132c812c340c8e1927c2caf6d55185296b66201
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support skb->xmit_more in i40e is straightforward : we need to move
around i40e_maybe_stop_tx() call to correctly test netif_xmit_stopped()
before taking the decision to not kick the NIC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert two more Intel NIC drivers to dev_consume_skb_any() to help
make dropped packet profiling sane.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is global funcion pci_vfs_assigned(), so use it instead of composing
local one.
Signed-off-by: Ethan Zhao <ethan.kernel@gmail.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e version to 1.0.11 and i40evf version to 1.0.5.
Change-ID: I63a60fa2efe82aae87a8a3095f43218db57d46ce
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
This fixes the panic under traffic load when resetting. This issue
could also show up if/whenever there is a Tx-timeout.
Change-ID: Ie393a1f17fd5d962e56fc3bfe784899ef25402f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't restart Admin queue subtask if PF reset fails since we do
not have the AQ setup at that point. This patch makes sure we disable AQ
clean subtask when PF reset fails.
This will resolve an occasional kernel panic when PF reset fails for
some reason.
Change-ID: I11a747773362a8c5c0ad7a10cd34be0bda8eb9e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver is un-necessarily printing a warning that is only marginally
useful to the user. Make the warning only print if extended driver
string printing is enabled, other messages related to a reset event
will still continue to print.
Change-ID: I5e8beca6516a2f176cd2e72b0ac2b3b909e6c953
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we don't seem to be getting an LSE telling us link is going down
during set_phy_config (but we do get an LSE telling us we are coming
back up), fake one for the OS and tell them link is going down. Also
do an atomic restart no matter what because there are times the user
may want to end with link up even if they started with link down (like
if they accidentally set it to a speed that can't link and are trying to
fix it).
Change-ID: I0a642af9c1d0feb67bce741aba1a9c33bd349ed6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary setting of "ret" variable as it's already set at
the top of the function.
Change-ID: Icaccfc67f335817a23579b7c43625d59ad6c9925
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change "spoofck" to "spoofchk" to be consistent with as defined in netdev.
Change-ID: I9866d6284cb5f92c8d71dc0776c6d1e71dfb62a5
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the user to change auto-negotiation and speed settings if
link is down.
Change-ID: I372967c627682b5e1835f623a7cbf41b21b51043
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that fw has implemented dual speed module support, we can add ours.
Also, add the phy type for 1G LR/SR and set its media type to fiber.
Lastly, instead of a WARN_ON if the phy type is not recognized just print
a warning.
Change-ID: I2e5227d4a8c2907b0ed423038e5dbce774e466b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump versions for i40e to 1.0.4 and i40evf to 1.0.1.
Change-ID: I960c04da2c91bdf1d02f8e5011e68c34a634122d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.
Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Older firmware has an incorrect MAC VLAN filter that needs to be replaced
at startup, and now newer firmware doesn't have this problem. With this
change we no longer complain if the remove fails, and we only add the
new filter if the remove succeeded.
Setting a new LAA worked the first time, but didn't work well in successive
operations, including returning to the HW default address. This simplifies
the code that was trying to be too smart.
Lastly, this pulls the hardware default mac address out into separate
handling code and keeps the broadcast filtering from getting munged.
Change-ID: I1f54b002def04ffef2546febb9a4044385452f85
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is at least one case in the Firmware API where the response to a
command changes the buffer size field in the AQ descriptor to a larger
number than what the request's buffer size started as. This is in addition
to setting an error flag and is in order to tell the requester how much
larger a buffer is required for the answer. We need to be sure not to
use that number when dumping the contents of the data buffer because it
can send us into the weeds and generate an invalid pointer exception.
This patch adds a max buffer size parameter to the print helper to be
sure the code knows when to stop.
Change-ID: Ib84f7ed72140fe9d600086d8f2002fc5d8753092
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check during handle_link_event for unqualified
module when link is down and there is a module plugged. If found,
print a message.
Change-ID: Ibd8666d77d3044c2a3dd4d762d3ae9ac6e18e943
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change vsi->num_queue_pairs to equal the number that are configured
by the VF. This, in turn, limits the number of queues that are
enable/disabled. This fixes the mismatched case for when a VF configures
fewer queues than is allocated to it by the PF.
Change other sections to use alloc_queue_pairs as warranted.
Change-ID: I0de1b55c9084e7be6acc818da8569f12128a82c2
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the l2tsel bit on Rx queue contexts that are assigned to VFs so
that the VF can get the stripped VLAN tag.
Change-ID: I7d9bc56238a9ea9baf5e8a97e69b9e27ebb9d169
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This helps know how many times the interface had to flush and replay FD
filter table, which gives an indication on how often we are getting FD
table full situation.
Also check on certain pf states before proceeding to add or delete
filters since we can't add or delete filters if we are in those states.
Change-ID: I97f5bbbea7146833ea61af0e08ea794fccba1780
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of disabling ATR when we get a programming error, we now
will wait it out to see if some room gets created by ATR rule deletion.
If we still have too many errors and ATR filter count did not change
much, its time to flush and replay. We no more auto-disable ATR when
we have errors in programming.
The disabling of ATR when we get programming error was buggy and
was still adding new rules and causing continuous errors. With this
policy change we flush instead when we see too many errors.
ATR is still disabled if we add a SB rule for TCP/IPv4 flow type,
more logic is added to re-enable it once all SB TCP/IPv4 rules are gone.
Change-ID: I77edcbeab9500c72a7e0bd7b5c5b113ced133a9c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the message that gets printed when adding/deleting a filter to
the SB, so that user can tell if a filter was added or deleted.
Print filter add failures only in case of SB filters. For ATR the
information is not useful to the user and hence suppress it unless in
higher debug mode.
Change-ID: I78d7a7a6ecfa82a38a582b0d7b4da038355e3735
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the wording of the flow director add/remove and
asynchronous failure messages to include fd_id to try and add some
way to track the operations on a given fd_id. Its not perfect, but
its better than what we had as PCTYPE can apply to several different
filter requests.
This patch also removes a redundant message when filter
addition fails due to full condition.
Change-ID: Icf58b0603d4f162d9fc542f11a74866a907049f2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive hang detection routine was never being run when
PTP was enabled.
Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.
Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up. AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.
Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warnings:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:254:13: warning:
symbol 'i40e_write_nvm_aq' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix missing include in Intel i40e driver. Without this include linux next
tree won't compile.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.
Also fix it to send the correct seid to aq for multicast promiscuous set.
Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes comment for reset reason
Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
