Pull powerpc fixes from Ben Herrenschmidt:
"Here are a handful of powerpc fixes for 3.13.
The patches are reasonably trivial and self contained. Note the offb
patches outside of arch/powerpc, they are LE fixes for our
open-firmware 'dumb' framebuffer"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix up the kdump base cap to 128M
powernv: Fix VFIO support with PHB3
powerpc/52xx: Re-enable bestcomm driver in defconfigs
powerpc/pasemi: Turn on devtmpfs in defconfig
offb: Add palette hack for little endian
offb: Little endian fixes
powerpc: Fix PTE page address mismatch in pgtable ctor/dtor
powerpc/44x: Fix ocm_block allocation
powerpc: Fix build break with PPC_EARLY_DEBUG_BOOTX=y
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node
The current logic sets the kdump base to min of 2G or ppc64_rma_size/2.
On PowerNV kernel the first memory block 'memory@0' can be very large,
equal to the DIMM size with ppc64_rma_size value capped to 1G. Hence on
PowerNV, kdump base is set to 512M resulting kdump to fail while allocating
paca array. This is because, paca need its memory from RMA region capped
at 256M (see allocate_pacas()).
This patch lowers the kdump base cap to 128M so that kdump kernel can
successfully get memory below 256M for paca allocation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have recently found out that no iommu_groups could be found under
/sys/ on a P8. That prevents PCI passthrough from working.
During my investigation, I found out there seems to be a missing
iommu_register_group for PHB3. The following patch seems to fix the
problem. After applying it, I see iommu_groups under
/sys/kernel/iommu_groups/, and can also bind vfio-pci to an adapter,
which gives me a device at /dev/vfio/.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bestcomm driver has been moved to drivers/dma, so to select
this driver by default additionally CONFIG_DMADEVICES has to be
enabled. Currently it is not enabled in the config despite existing
CONFIG_PPC_BESTCOMM=y in the config files. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At least some distros expect it these days; turn it on. Also, random
churn from doing a savedefconfig for the first time in a year or so.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In pte_alloc_one(), pgtable_page_ctor() is passed an address that has
not been converted by page_address() to the newly allocated PTE page.
When the PTE is freed, __pte_free_tlb() calls pgtable_page_dtor()
with an address to the PTE page that has been converted by page_address().
The mismatch in the PTE's page address causes pgtable_page_dtor() to access
invalid memory, so resources for that PTE (such as the page lock) is not
properly cleaned up.
On PPC32, only SMP kernels are affected.
On PPC64, only SMP kernels with 4K page size are affected.
This bug was introduced by commit d614bb0412
"powerpc: Move the pte free routines from common header".
On a preempt-rt kernel, a spinlock is dynamically allocated for each
PTE in pgtable_page_ctor(). When the PTE is freed, calling
pgtable_page_dtor() with a mismatched page address causes a memory leak,
as the pointer to the PTE's spinlock is bogus.
On mainline, there isn't any immediately obvious symptoms, but the
problem still exists here.
Fixes: d614bb0412 "powerpc: Move the pte free routes from common header"
Cc: Paul Mackerras <paulus@samba.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-stable <stable@vger.kernel.org> # v3.10+
Signed-off-by: Hong H. Pham <hong.pham@windriver.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Allocate enough memory for the ocm_block structure, not just a pointer
to it.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A kernel configured with PPC_EARLY_DEBUG_BOOTX=y but PPC_PMAC=n and
PPC_MAPLE=n will fail to link:
btext.c:(.text+0x2d0fc): undefined reference to `.rmci_off'
btext.c:(.text+0x2d214): undefined reference to `.rmci_on'
Fix it by making the build of rmci_on/off() depend on
PPC_EARLY_DEBUG_BOOTX, which also enable the only code that uses them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In checkin
5551a34e5a x86-64, build: Always pass in -mno-sse
we unconditionally added -mno-sse to the main build, to keep newer
compilers from generating SSE instructions from autovectorization.
However, this did not extend to the special environments
(arch/x86/boot, arch/x86/boot/compressed, and arch/x86/realmode/rm).
Add -mno-sse to the compiler command line for these environments, and
add -mno-mmx to all the environments as well, as we don't want a
compiler to generate MMX code either.
This patch also removes a $(cc-option) call for -m32, since we have
long since stopped supporting compilers too old for the -m32 option,
and in fact hardcode it in other places in the Makefiles.
Reported-by: Kevin B. Smith <kevin.b.smith@intel.com>
Cc: Sunil K. Pandey <sunil.k.pandey@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: H. J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/n/tip-j21wzqv790q834n7yc6g80j1@git.kernel.org
Cc: <stable@vger.kernel.org> # build fix only
data earlier but are not initializing it from device tree. In addition
to this fix we eventually also be fix the issues in the .dts files
and drivers, but that's too intrusive for the -rc cycle and must be
done later on.
Also a fix for a regression where we now are wrongly trying to initialize
devices on secure omaps like n900 and n9* when booted using device tree.
We need to set aes, sham and timer12 to disabled mode for secure
devices as they are claimed by the firmware running in the secure mode.
And two more legacy booting vs device tree based booting fixes for
am3517 that I did not notice earlier until Nishant Menon reported
these to me few days ago. With these we're good to go having v3.13
working both for legacy booting and device tree based booting, and we
can then go ahed and drop the legacy booting for mach-omap2 for v3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=d3MF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/yet-more-dt-regressions-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
A rather big fix for a regression where we have dropped omap4 hwmod
data earlier but are not initializing it from device tree. In addition
to this fix we eventually also be fix the issues in the .dts files
and drivers, but that's too intrusive for the -rc cycle and must be
done later on.
Also a fix for a regression where we now are wrongly trying to initialize
devices on secure omaps like n900 and n9* when booted using device tree.
We need to set aes, sham and timer12 to disabled mode for secure
devices as they are claimed by the firmware running in the secure mode.
And two more legacy booting vs device tree based booting fixes for
am3517 that I did not notice earlier until Nishant Menon reported
these to me few days ago. With these we're good to go having v3.13
working both for legacy booting and device tree based booting, and we
can then go ahed and drop the legacy booting for mach-omap2 for v3.14.
* tag 'omap-for-v3.13/yet-more-dt-regressions-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (494 commits)
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
+Linux 3.13-rc3
The __do_cache_op function operates with a 'chunk' size of one page
but fails to limit the size of the final chunk so as to not exceed
the specified memory region. Fix this.
Cc: <stable@vger.kernel.org>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes corner case when (fp + 4) overflows unsigned long,
for example: fp = 0xFFFFFFFF -> fp + 4 == 3.
Cc: <stable@vger.kernel.org>
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_wchan() is lockless. Task may wakeup at any time and change its own stack,
thus each next stack frame may be overwritten and filled with random stuff.
/proc/$pid/stack interface had been disabled for non-current tasks, see [1]
But 'wchan' still allows to trigger stack frame unwinding on volatile stack.
This patch fixes oops in unwind_frame() by adding stack pointer validation on
each step (as x86 code do), unwind_frame() already checks frame pointer.
Also I've found another report of this oops on stackoverflow (irony).
Link: http://www.spinics.net/lists/arm-kernel/msg110589.html [1]
Link: http://stackoverflow.com/questions/18479894/unwind-frame-cause-a-kernel-paging-error
Cc: <stable@vger.kernel.org>
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To get updated __pv_phys_offset, setup_dma_zone() needs to be
called after early_paging_init().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current code is using PHYS_OFFSET to calculate the arm_dma_limit which
will lead to wrong calculations in cases where PHYS_OFFSET is updated
runtime.
So fix the code by using __pv_phys_offset instead of PHYS_OFFSET.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Peter reports that OMAP audio broke with the recent fix for these
checks, caused by OMAP audio using a 64-bit DMA mask. We should
allow 64-bit DMA masks even with 32-bit dma_addr_t if we can be sure
the amount of RAM we have won't allow the 32-bit dma_addr_t to
overflow. Unfortunately, the checks to detect overflow were not
correct.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit dc75925d(OMAP: hwmod: Fix the missing braces) introduced
missing braces, however, we just set return result if clk_get fail
and we populate the error pointer in clk pointer and pass it along to
clk_prepare. This is wrong. The intent seems to be retry remaining
clocks if they are available and warn the ones we cant find clks for.
With the current logic, we see the following crash:
omap_hwmod: l3_main: cannot clk_get interface_clk emac_ick
Unable to handle kernel NULL pointer dereference at virtual address 00000032
pgd = c0004000
[00000032] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc1-00044-gcc9fd5a-dirty #19
task: ce0c3440 ti: ce0c4000 task.ti: ce0c4000
PC is at __clk_prepare+0x10/0x74
LR is at clk_prepare+0x14/0x24
<snip>
[<c044d59c>] (__clk_prepare+0x10/0x74) from [<c044d9b0>] (clk_prepare+0x14/0x24)
[<c044d9b0>] (clk_prepare+0x14/0x24) from [<c077d8c4>] (_init+0x24c/0x3bc)
[<c077d8c4>] (_init+0x24c/0x3bc) from [<c0027328>] (omap_hwmod_for_each+0x34/0x5c)
[<c0027328>] (omap_hwmod_for_each+0x34/0x5c) from [<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40)
[<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40) from [<c0008928>] (do_one_initcall+0x38/0x168)
[<c0008928>] (do_one_initcall+0x38/0x168) from [<c0771be8>] (kernel_init_freeable+0xfc/0x1cc)
[<c0771be8>] (kernel_init_freeable+0xfc/0x1cc) from [<c0521064>] (kernel_init+0x8/0x110)
[<c0521064>] (kernel_init+0x8/0x110) from [<c000e568>] (ret_from_fork+0x14/0x2c)
Code: e92d4038 e2504000 01a05004 0a000005 (e5943034)
So, just warn and continue instead of proceeding and crashing, with
missing clock nodes/bad data, we will eventually fail, however we
should now have enough information to identify the culprit.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In _ocp_softreset(), after _set_softreset() + write_sysconfig(),
the hwmod's sysc_cache will always contain SOFTRESET bit set
so all further writes to sysconfig using this cache will initiate
a repeated SOFTRESET e.g. enable_sysc(). This is true for OMAP3 like
platforms that have RESET_DONE status in the SYSSTATUS register and
so the the SOFTRESET bit in SYSCONFIG is not automatically cleared.
It is not a problem for OMAP4 like platforms that indicate RESET
completion by clearing the SOFTRESET bit in the SYSCONFIG register.
This repeated SOFTRESET is undesired and was the root cause of
USB host issues on OMAP3 platforms when hwmod was allowed to do the
SOFTRESET for the USB Host module.
To fix this we clear the SOFTRESET bit and update the sysconfig
register + sysc_cache using write_sysconfig().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
[paul@pwsan.com: renamed _clr_softreset() to _clear_softreset()]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this, the USB devices are sometimes not detected on OMAP4 Panda
with u-boot v2013.10.
Unlike what the comment states, errata i660 does not state that we
can't RESET the USB host module. Instead it states that RESET is the
only way to recover from a deadlock situation.
RESET ensures that the module is in a known good state irrespective
of what bootloader does with the module, so it must be done at boot.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> # Panda, BeagleXM
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Fixes: af88fa9aa7 ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that the svcpu sync is interrupt aware we can enable interrupts
earlier in the exit code path again, moving 32bit and 64bit closer
together.
While at it, document the fact that we're always executing the exit
path with interrupts enabled so that the next person doesn't trap
over this.
Signed-off-by: Alexander Graf <agraf@suse.de>
As soon as we get back to our "highmem" handler in virtual address
space we may get preempted. Today the reason we can get preempted is
that we replay interrupts and all the lazy logic thinks we have
interrupts enabled.
However, it's not hard to make the code interruptible and that way
we can enable and handle interrupts even earlier.
This fixes random guest crashes that happened with CONFIG_PREEMPT=y
for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
The kvmppc_copy_{to,from}_svcpu functions are publically visible,
so we should also export them in a header for others C files to
consume.
So far we didn't need this because we only called it from asm code.
The next patch will introduce a C caller.
Signed-off-by: Alexander Graf <agraf@suse.de>
We call a C helper to save all svcpu fields into our vcpu. The C
ABI states that r12 is considered volatile. However, we keep our
exit handler id in r12 currently.
So we need to save it away into a non-volatile register instead
that definitely does get preserved across the C call.
This bug usually didn't hit anyone yet since gcc is smart enough
to generate code that doesn't even need r12 which means it stayed
identical throughout the call by sheer luck. But we can't rely on
that.
Signed-off-by: Alexander Graf <agraf@suse.de>
The am3517 is wrongly booting as omap3 which means that the am3517
specific devices like Ethernet won't work when booted with device
tree. Now with the new devices defined in am3517.dtsi, let's use
that instead of the omap3.dtsi, and add a separate machine entry
for am3517 so am3517-evm can use it.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated comments and fixed build without omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am3517 there are some extra devices compared to omap3.dtsi that
we currently have not defined. Let's fix that by adding am3517.dtsi
file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have some device tree properties where the ti,hwmod have multiple
values:
am33xx.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
am4372.dtsi: ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
dra7.dtsi: ti,hwmods = "l3_main_1", "l3_main_2";
omap3.dtsi: ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
omap3.dtsi: ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
omap4.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
omap5.dtsi: ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
That's not correct way of doing things in this case because these are
separate devices with their own address space, interrupts, SYSCONFIG
registers and can set their PM states independently.
So they should all be fixed up to be separate devices in the .dts files.
We also have the related data removed for at least omap4 in commit
3b9b10151c (ARM: OMAP4: hwmod data: Clean up the data file), so
that data is wrongly initialized as null data.
So we need to fix two bugs:
1. We are only checking the first entry of the ti,hwmods property
This means that we're only initializing the first hwmods entry
instead of the ones listed in the ti,hwmods property.
2. We are only checking the child nodes, not the nodes themselves
This means that anything listed at OCP level is currently just
ignored and unitialized and at least the omap4 case, with the
legacy data missing from the hwmod.
Fix both of the issues by using an index to the ti,hwmods property
and changing the hwmod lookup function to also check the current node
for ti,hwmods property instead of just the children.
While at it, let's also add some warnings for the bad data so it's
easier to fix.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modify the value of PMD_SECT_PROT_NONE to match that of PTE_NONE. This
should have been in commit 3676f9ef54 (Move PTE_PROT_NONE higher up).
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Cc: <stable@vger.kernel.org> # 3.11+: 3676f9ef54: arm64: Move PTE_PROT_NONE higher up
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Write-combine and cacheable mappings use Normal memory on arm64. On SMP
systems, the pte needs the shareability bit which is set in
pgprot_default. Use this for defining PROT_DEFAULT used by ioremap_wc
and ioremap_cache (Device memory is shareable by default, does not need
additional attributes).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The refactoring of el2_setup split code setting up EL2 and detecting the
CPU boot mode in separate chunks. This allows the code that sets up EL2 to
run in an endian independent way - ie before the endianess is set up in
the respective sctlr registers.
This patch brings secondary_entry up-to-date so that CPUs entering the
kernel through this code path set-up EL2 and the cpu boot mode properly.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Mark Rutland <mark.rutand@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rather than continue to add per platform defaults, make the default a
likely common core count. 8 is also the default for x86.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently there is no dsb between the tlbi in __cpu_setup and the write
to SCTLR_EL1 which enables the MMU in __turn_mmu_on. This means that the
TLB invalidation is not guaranteed to have completed at the point
address translation is enabled, leading to a number of possible issues
including incorrect translations and TLB conflict faults.
This patch moves the tlbi in __cpu_setup above an existing dsb used to
synchronise I-cache invalidation, ensuring that the TLBs have been
invalidated at the point the MMU is enabled.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The EVENT_CONSTRAINT_END() macro defines the end marker as
a constraint with a weight of zero. This was all fine
until we blacklisted the corrupting memory events on
Intel IvyBridge. These events are blacklisted by using
a counter bitmask of zero. Thus, they also get a constraint
weight of zero.
The iteration macro: for_each_constraint tests the weight==0.
Therefore, it was stopping at the first blacklisted event, i.e.,
0xd0. The corrupting events were therefore considered as
unconstrained and were scheduled on any of the generic counters.
This patch fixes the end marker to have a weight of -1. With
this, the blacklisted events get an empty constraint and cannot
be scheduled which is what we want for now.
Signed-off-by: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Reviewed-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: ak@linux.intel.com
Cc: jolsa@redhat.com
Cc: zheng.z.yan@intel.com
Link: http://lkml.kernel.org/r/20131204232437.GA10689@starlight
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 and EFI fixes from Peter Anvin:
"Half of these are EFI-related:
The by far biggest change is the change to hold off the deletion of a
sysfs entry while a backend scan is in progress. This is to avoid
calling kmemdup() while under a spinlock.
The other major change is for each entry in the EFI pstore backend to
get a unique identifier, as required by the pstore filesystem proper.
The other changes are:
A fix to the recent consolidation and optimization of using "asm goto"
with read-modify-write operation, which broke the bitops; specifically
in such a way that we could end up generating invalid code.
A build hack to make sure we compile with -mno-sse. icc, and most
likely future versions of gcc, can generate SSE instructions unless we
tell it not to.
A comment-only patch to a change the was due in part to an unpublished
erratum; now when the erratum is published we want to add a comment
explaining why"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic, doc: Justification for disabling IO APIC before Local APIC
x86, bitops: Correct the assembly constraints to testing bitops
x86-64, build: Always pass in -mno-sse
efi-pstore: Make efi-pstore return a unique id
x86/efi: Fix earlyprintk off-by-one bug
efivars, efi-pstore: Hold off deletion of sysfs entry until the scan is completed
Since erratum AVR31 in "Intel Atom Processor C2000 Product Family
Specification Update" is now published, I added a justification
comment for disabling IO APIC before Local APIC, as changed in commit:
522e664644 x86/apic: Disable I/O APIC before shutdown of the local APIC
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1386202069-51515-1-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In checkin:
0c44c2d0f4 x86: Use asm goto to implement better modify_and_test() functions
the various functions which do modify and test were unified and
optimized using "asm goto". However, this change missed the detail
that the bitops require an "Ir" constraint rather than an "er"
constraint ("I" = integer constant from 0-31, "e" = signed 32-bit
integer constant). This would cause code to miscompile if these
functions were used on constant bit positions 32-255 and the build to
fail if used on constant bit positions above 255.
Add the constraints as a parameter to the GEN_BINARY_RMWcc() macro to
avoid this problem.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/529E8719.4070202@zytor.com
to align platform code to driver's
usage of platform_get_resource_byname()
This is needed to start successfully probing
audio again. The regression was introduced
in v3.13 merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJSn6GfAAoJEGFBu2jqvgRNvw8P/iqsiOdwDbabbHMa8ZscEJ6B
Dtijef9v+5cNUd6Q+ulP+Fo8g5uxe/ZFwBTAWd6TbfCczvCXHPfN0p1NoBu7B2YS
4I5/7OKXqNGPeqNvurcpqRgCdp58bTEiK6Fnfflbka7cXUFahL7jPgOE0/rHOM9V
ZwdTBRDK8ieM3ovTUFECcWJ/QE5GurqcyP0csbTxOR7R2EhM/genwPSzrh9BhmNJ
Rz+Vs7ns4wcEPHo0VdR5wHvD4rPy8LZ70EMVAVPO1P1YTXgh9hehcP8G8LvhNVyM
g80zRP6g2e1bTtDHMFkEjScSWuLWSWNeTiLD0SuUY6rl0lwx2TjXN9dCPdPbPHJR
wGfUFsTO3kueoyyUGKHNN9AfRBfv1BbDkclqPxca2Hvn5q2/IjxED07toMvCo4E/
pAcb7IKVhujpSY0SbYkGHhvuvSQHuL4dUvAaPL/sfeX8WYZ61+XocxpnL/z13SOh
QwKvDO2gaOe71Tq/FAyg+8r+u+OAbJwgEp+QjkZ31ixSHR6GXWSGR7x0+R1LETnW
pWHZIVi09AkAOLkmbwTsmnHemjZR/USoAL3XCrFb4pRgwFhxQqwkJWyqXOdZhxeJ
wzJ/YKWeop/an1wFIYhGtXGhDV/lLwVNV/y/sPuDnwPlkc/6MWU34MjiaGyLcgxZ
rdimobHpRrHJgqEavbwi
=13O8
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
This pull request includes a patch
to align platform code to driver's
usage of platform_get_resource_byname()
This is needed to start successfully probing
audio again. The regression was introduced
in v3.13 merge window.
* tag 'davinci-fixes-for-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: Fix McASP mem resource names
Signed-off-by: Olof Johansson <olof@lixom.net>
The ASoC McASP driver looks for the mem resources by name
"mpu" and "dat" regions.
Change/add the needed name for the mem resources so the driver can pick the
correct resource.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
GPIO IRQ support and a fix for some random memory
corruption. The bugs were introduced during v3.13
merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=1N0A
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori:
This pull request contains a fixe for broken unbanked
GPIO IRQ support and a fix for some random memory
corruption. The bugs were introduced during v3.13
merge window.
* tag 'davinci-fixes-for-v3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
Graceful reboot and poweroff via IPMI commands to the management
processor don't work. Power and reset keys are events from the
management processor which are generated via IPC messages. Passing
the keys to userspace does not work as neither acpid nor a desktop
environment are present.
This adds a notifier handler for the IPC messages so the kernel can
handle the key events directly and IPMI graceful shutdown will work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from board
files to DT. Tony thinks this was the last major set of fixes, with
maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed PCIe
hardware, i.e. incorrect number of busses on some SoCs, etc. The line
delta adds up due to various ranges moving around when this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in my
test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91, a couple
of reverts for ux500, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PljB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
Pull parsic updates from Helge Deller:
- a fix for the mmap(MAP_FIXED|MAP_SHARED) syscall to the same address
which was already given in a previous call (fixes locale-gen on
debian)
- change the memory layout of the kernel to avoid the need for the
-mlong-calls compiler option (depends on commit 5ecbe3c3c6 -
"kernel/extable: fix address-checks for core_kernel and init areas")
- defconfig updates, e.g. use the SIL680 driver instead of the SIIMAGE
driver
- add more parisc machine names to the machine database
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: update 64bit defconfigs and use SIL680 instead of SIIMAGE driver
parisc: remove CONFIG_MLONGCALLS=y from defconfigs
parisc: fix kernel memory layout in vmlinux.ld.S
parisc: use kernel_text_address() in unwind functions
parisc: remove empty SERIAL_PORT_DFNS in serial.h
parisc: add some more machine names to hardware database
parisc: fix mmap(MAP_FIXED|MAP_SHARED) to already mmapped address
Pull crypto fixes from Herbert Xu:
"This push fixes a number of crashes triggered by a previous crypto
self-test update. It also fixes a build problem in the caam driver,
as well as a concurrency issue in s390.
Finally there is a pair of fixes to bugs in the crypto scatterwalk
code and authenc that may lead to crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - fix sglen in test_aead for case 'dst != src'
crypto: talitos - fix aead sglen for case 'dst != src'
crypto: caam - fix aead sglen for case 'dst != src'
crypto: ccm - Fix handling of zero plaintext when computing mac
crypto: s390 - Fix aes-xts parameter corruption
crypto: talitos - corrrectly handle zero-length assoc data
crypto: scatterwalk - Set the chain pointer indication bit
crypto: authenc - Find proper IV address in ablkcipher callback
crypto: caam - Add missing Job Ring include
Pull timer fixes from Thomas Gleixner:
- timekeeping: Cure a subtle drift issue on GENERIC_TIME_VSYSCALL_OLD
- nohz: Make CONFIG_NO_HZ=n and nohz=off command line option behave the
same way. Fixes a long standing load accounting wreckage.
- clocksource/ARM: Kconfig update to avoid ARM=n wreckage
- clocksource/ARM: Fixlets for the AT91 and SH clocksource/clockevents
- Trivial documentation update and kzalloc conversion from akpms pile
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix another inconsistency between CONFIG_NO_HZ=n and nohz=off
time: Fix 1ns/tick drift w/ GENERIC_TIME_VSYSCALL_OLD
clocksource: arm_arch_timer: Hide eventstream Kconfig on non-ARM
clocksource: sh_tmu: Add clk_prepare/unprepare support
clocksource: sh_tmu: Release clock when sh_tmu_register() fails
clocksource: sh_mtu2: Add clk_prepare/unprepare support
clocksource: sh_mtu2: Release clock when sh_mtu2_register() fails
ARM: at91: rm9200: switch back to clockevents_config_and_register
tick: Document tick_do_timer_cpu
timer: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
NOHZ: Check for nohz active instead of nohz enabled
From: Eric Trudeau <etrudeau@broadcom.com>
xen_hvm_resume_frames stores the physical address of the grant table.
englighten.c was incorrectly setting it as if it was a page frame number.
This caused the table to be mapped into the guest at an unexpected physical
address.
Additionally, a warning is improved to include the grant table address which
failed in xen_remap.
Signed-off-by: Eric Trudeau <etrudeau@broadcom.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Always pass in the -mno-sse argument, regardless if
-preferred-stack-boundary is supported. We never want to generate SSE
instructions in the kernel unless we *really* know what we're doing.
According to H. J. Lu, any version of gcc new enough that we support
it at all should handle the -mno-sse option, so just add it
unconditionally.
Reported-by: Kevin B. Smith <kevin.b.smith@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: H. J. Lu <hjl.tools@gmail.com>
Link: http://lkml.kernel.org/n/tip-j21wzqv790q834n7yc6g80j1@git.kernel.org
Cc: <stable@vger.kernel.org> # build fix only
Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable MMC/SD on the Broadcom mobile platforms, and increase the block
minors from the default 8 to 16 (since the Broadcom board by default
has root on the 8th partition).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.12
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
BeagleBone Black uses the TI CPSW ethernet controller, enable it in the
multi_v7_defconfig for testing coverage purposes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v3.12
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes build error which was introduced by commit
812cb83a56 (Implement HAVE_CONTEXT_TRACKING).
[*]https://lkml.org/lkml/2013/11/23/103
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSnJuAAAoJEFjIrFwIi8fJj7sIAJQgSEMWJcEOBJ3lujfbhhKr
9GYfyNILfBjaOcH3LkA354U0JB3y4vON/xz6ONzMO4X7Jj6oUzACeEluq2iexlji
VDxqtnDJGS/82TcIN5xOVKRZbIqZ0xdRjK2f4h7AU9lIoIk+SJEJIycG1RGqqrmr
0nv39lUMjQhXNDhUjyt7e6JQj5GHrP0hzp5ngEQGcquPKbHXUInlwkB/kCH3zwju
2kEYQyKSWFoZCVtIBDeHplcZw9r/zWyOHBxjWOVoI/KZk8k+6d2breC3hv0lrhvU
qkJwzJcKZGlFdiCVHLbo3sTHf0NvvfF+qBCv7JbsymYaQc5SkrATmQ/DAUOssg0=
=emSu
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
With git commit 79c74ecbeb
"s390/time,vdso: convert to the new update_vsyscall interface"
the new update_vsyscall function already does the sum of xtime
and wall_to_monotonic. The old update_vsyscall function only
copied the wall_to_monotonic offset. The vdso code needs to be
modified to take this into consideration.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The code to use the ECTG instruction to calculate the cputime for the
current thread is currently used only for the per-thread CPU-clock
with the clockid -2 (PID=0, VIRT=1). Use the same code for the clockid
CLOCK_THREAD_CPUTIME_ID to speed up the more common clockid as well.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The access-list entry is supposed to have the fetch-only bit set, however
a reserved bit got set instead.
Userspace isn't able to write to the page anyway since the accessed page
has the read-only bit set. So this saves us only for bad surprises in the
future if the reserved bit gets used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In current models, maximum number of active cores is 101.
[heiko.carstens@de.ibm.com]: Xose's patch increased the maximum possible
value of CONFIG_NR_CPUS to 101. I changed this to 256 instead.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
struct sclp_cpu_info contains entries only for 255 cpus, while the new
smp fallback sigp detection code will fill up to 256 entries.
Even though there is no machine available which has 256 cpus and where
in addition the fallback sigp cpu detection code will be used we better
fix this, to prevent out of bound accesses.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If CONFIG_PM is not defined, then arch/arm/mach-at91/pm.c is not
compiled in. This patch creates an inline function that does nothing
if CONFIG_PM is not defined.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
With some devices, transfer hangs during I2C frame transmission. This issue
disappears when reducing the internal frequency of the TWI IP. Even if it is
indicated that internal clock max frequency is 66MHz, it seems we have
oversampling on I2C signals making TWI believe that a transfer in progress
is done.
This fix has no impact on the I2C bus frequency.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull UML fixes from Richard Weinberger:
"Fixes two regressions which got introduced this merge window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Build always with -mcmodel=large on 64bit
um: Rename print_stack_trace to do_stack_trace
Pull ARM fixes from Russell King:
"Some ARM fixes, the biggest of which is the fix for the signal return
codes; this came up due to an interaction between the V7M nommu
changes and the BE8 changes. Dave Martin spotted that the kexec
trampoline wasn't being correctly copied (in a way which allows
Thumb-2 to work).
I've also fixed a number of breakages on footbridge platforms as I've
upgraded one of my machines to v3.12... one which had a 1200 day
uptime"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7907/1: lib: delay-loop: Add align directive to fix BogoMIPS calculation
ARM: 7897/1: kexec: Use the right ISA for relocate_new_kernel
ARM: 7895/1: signal: fix armv7-m build issue in sigreturn_codes.S
ARM: footbridge: fix EBSA285 LEDs
ARM: footbridge: fix VGA initialisation
ARM: fix booting low-vectors machines
ARM: dma-mapping: check DMA mask against available memory
On UML SUBARCH can be x86, x86_64 and i386 and if it is x86
we use uname -m to select a defconfig.
Therefore we can no longer use -mcmodel=large only if SUBARCH
is x86_64.
Reported-and-tested-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
We cannot use print_stack_trace because the name conflicts
with linux/stacktrace.h.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Copying a function with memcpy() and then trying to execute the
result isn't trivially portable to Thumb.
This patch modifies the kexec soft restart code to copy its
assembler trampoline relocate_new_kernel() using fncpy() instead,
so that relocate_new_kernel can be in the same ISA as the rest of
the kernel without problems.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Tested-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After "ARM: signal: sigreturn_codes should be endian neutral to
work in BE8" commit, thumb only platforms, like armv7m, fails to
compile sigreturn_codes.S. The reason is that for such arch
values '.arm' directive and arm opcodes are not allowed.
Fix conditionally enables arm opcodes only if no CONFIG_CPU_THUMBONLY
defined and it uses .org instructions to keep sigreturn_codes
layout.
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The LEDs register is write-only: it can't be read-modify-written.
- The LEDs are write-1-for-off not 0.
- The check for the platform was inverted.
Fixes: cf6856d693 ("ARM: mach-footbridge: retire custom LED code")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
When building a 64bit kernel sometimes functions in the .init section were not
able to reach the standard kernel function. Main reason for this problem is,
that the linkage tables (.plt, .opd, .dlt) tend to become pretty huge and thus
the distance gets too big for short calls.
One option to avoid this is to use the -mlong-calls compiler option, but this
increases the binary size and introduces a performance penalty.
Instead, with this patch we just lay out the binary differently. Init code is
stored first, followed by text, R/O and finally R/W data. This means, that init
and text code is now much closer to each other, which is sufficient to reach
each other by short calls.
Signed-off-by: Helge Deller <deller@gmx.de>
If architectures don't support SERIAL_PORT_DFNS, they need not define it
to "nothing", the related drivers need do it by themselves (e.g. 8250
serial driver).
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Sadly the correct names for machines which end with a question-mark aren't
known, so let's give it a best-guessed-name.
Signed-off-by: Helge Deller <deller@gmx.de>
locale-gen on Debian showed a strange problem on parisc:
mmap2(NULL, 536870912, PROT_NONE, MAP_SHARED, 3, 0) = 0x42a54000
mmap2(0x42a54000, 103860, PROT_READ|PROT_WRITE, MAP_SHARED|MAP_FIXED, 3, 0) = -1 EINVAL (Invalid argument)
Basically it was just trying to re-mmap() a file at the same address
which it was given by a previous mmap() call. But this remapping failed
with EINVAL.
The problem is, that when MAP_FIXED and MAP_SHARED flags were used, we didn't
included the mapping-based offset when we verified the alignment of the given
fixed address against the offset which we calculated it in the previous call.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10+
It's no good setting vga_base after the VGA console has been
initialised, because if we do that we get this:
Unable to handle kernel paging request at virtual address 000b8000
pgd = c0004000
[000b8000] *pgd=07ffc831, *pte=00000000, *ppte=00000000
0Internal error: Oops: 5017 [#1] ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0+ #49
task: c03e2974 ti: c03d8000 task.ti: c03d8000
PC is at vgacon_startup+0x258/0x39c
LR is at request_resource+0x10/0x1c
pc : [<c01725d0>] lr : [<c0022b50>] psr: 60000053
sp : c03d9f68 ip : 000b8000 fp : c03d9f8c
r10: 000055aa r9 : 4401a103 r8 : ffffaa55
r7 : c03e357c r6 : c051b460 r5 : 000000ff r4 : 000c0000
r3 : 000b8000 r2 : c03e0514 r1 : 00000000 r0 : c0304971
Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
which is an access to the 0xb8000 without the PCI offset required to
make it work.
Fixes: cc22b4c185 ("ARM: set vga memory base at run-time")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
Commit f6f91b0d9f (ARM: allow kuser helpers to be removed from the
vector page) required two pages for the vectors code. Although the
code setting up the initial page tables was updated, the code which
allocates page tables for new processes wasn't, neither was the code
which tears down the mappings. Fix this.
Fixes: f6f91b0d9f ("ARM: allow kuser helpers to be removed from the vector page")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
Some buses have negative offsets, which causes the DMA mask checks to
falsely fail. Fix this by using the actual amount of memory fitted in
the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Remove preempt_count modifications in the arm64 IRQ handling code
since that's already dealt with in generic irq_enter/irq_exit
- PTE_PROT_NONE bit moved higher up to avoid overlapping with the
hardware bits (for PROT_NONE mappings which are pte_present)
- Big-endian fixes for ptrace support
- Asynchronous aborts unmasking while in the kernel
- pgprot_writecombine() change to create Normal NonCacheable memory
rather than Device GRE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=nfKM
-----END PGP SIGNATURE-----
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 fixes from Catalin Marinas:
- Remove preempt_count modifications in the arm64 IRQ handling code
since that's already dealt with in generic irq_enter/irq_exit
- PTE_PROT_NONE bit moved higher up to avoid overlapping with the
hardware bits (for PROT_NONE mappings which are pte_present)
- Big-endian fixes for ptrace support
- Asynchronous aborts unmasking while in the kernel
- pgprot_writecombine() change to create Normal NonCacheable memory
rather than Device GRE
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Move PTE_PROT_NONE higher up
arm64: Use Normal NonCacheable memory for writecombine
arm64: debug: make aarch32 bkpt checking endian clean
arm64: ptrace: fix compat registes get/set to be endian clean
arm64: Unmask asynchronous aborts when in kernel mode
arm64: dts: Reserve the memory used for secondary CPU release address
arm64: let the core code deal with preempt_count
Pull s390 updates from Martin Schwidefsky:
"One performance improvement and a few bug fixes. Two of the fixes
deal with the clock related problems we have seen on recent kernels"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: handle asce-type exceptions as normal page fault
s390,time: revert direct ktime path for s390 clockevent device
s390/time,vdso: convert to the new update_vsyscall interface
s390/uaccess: add missing page table walk range check
s390/mm: optimize copy_page
s390/dasd: validate request size before building CCW/TCW request
s390/signal: always restore saved runtime instrumentation psw bit
PTE_PROT_NONE means that a pte is present but does not have any
read/write attributes. However, setting the memory type like
pgprot_writecombine() is allowed and such bits overlap with
PTE_PROT_NONE. This causes mmap/munmap issues in drivers that change the
vma->vm_pg_prot on PROT_NONE mappings.
This patch reverts the PTE_FILE/PTE_PROT_NONE shift in commit
59911ca432 (ARM64: mm: Move PTE_PROT_NONE bit) and moves PTE_PROT_NONE
together with the other software bits.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Cc: <stable@vger.kernel.org> # 3.11+
This provides better performance compared to Device GRE and also allows
unaligned accesses. Such memory is intended to be used with standard RAM
(e.g. framebuffers) and not I/O.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Dave reported seeing the following incorrect output on his Thinkpad T420
when using earlyprintk=efi,
[ 0.000000] efi: EFI v2.00 by Lenovo
ACPI=0xdabfe000 ACPI 2.0=0xdabfe014 SMBIOS=0xdaa9e000
The output should be on one line, not split over two. The cause is an
off-by-one error when checking that the efi_y coordinate hasn't been
incremented out of bounds.
Reported-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The current breakpoint instruction checking code for A32 is not endian
clean. Fix this with appropriate byte-swapping when retrieving
instructions.
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On a BE system the wrong half of the X registers is retrieved/written
when attempting to get/set the value of aarch32 registers through
ptrace.
Ensure that types are the correct width so that the relevant
casting occurs.
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some s390 crypto algorithms incorrectly use the crypto_tfm structure to
store private data. As the tfm can be shared among multiple threads, this
can result in data corruption.
This patch fixes aes-xts by moving the xts and pcc parameter blocks from
the tfm onto the stack (48 + 96 bytes).
Cc: stable@vger.kernel.org
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The r8a7790 GPIO resources are currently incorrect. Fix that
by making them match the English r8a7790 v0.6 data sheet.
Tested with GPIO LED using Lager DT reference.
This problem has been present since GPIOs were added to the r8a7790 SoC by
f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller devices to
device tree") in v3.12-rc1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull powerpc fixes from Ben Herrenschmidt:
"The main thing that caused problem was that CONFIG_CPU_LITTLE_ENDIAN
got turned on with allyesconfig and such, which is not a very good
idea especially since it requires a newer toolchain than what most
people have.
So we turned it into a choice instead that defaults to big endian"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/windfarm: Fix XServe G5 fan control Makefile issue
arch/powerpc/kernel: Use %12.12s instead of %12s to avoid memory overflow
powerpc/signals: Improved mark VSX not saved with small contexts fix
powerpc/kdump: Adding symbols in vmcoreinfo to facilitate dump filtering
powerpc: allyesconfig should not select CONFIG_CPU_LITTLE_ENDIAN
powerpc: Fix error when cross building TAGS & cscope
powerpc/booke: Only check for hugetlb in flush if vma != NULL
powerpc/85xx: typo in dts: "interupt" (four devices)
powerpc/8xx: mfspr SPRN_TBRx in lieu of mftb/mftbu is not supported
powerpc/corenet64: compile with CONFIG_E{5,6}500_CPU well
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:
[ 3.186035] OMAPFB: omapfb_probe
[ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[ 3.196594] omapfb omapfb: failed to connect default display
[ 3.202667] omapfb omapfb: failed to init overlay connections
[ 3.208892] OMAPFB: free_resources
[ 3.212493] OMAPFB: free all fbmem
[ 3.216735] omapfb omapfb: failed to setup omapfb
As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).
Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.
To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.
When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.
Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling of Posted mode is seen to cause problems on dmtimer modules on AM33xx
(much like other OMAPs). Reference discussions on forums [1] [2]. Earlier
patch solving this on other OMAPs [3].
For OMAP SoCs with this errata, the fix has been to not enable Posted mode.
However, on some SoCs (atleast AM33xx) which carry this errata, Posted mode
is enabled on reset. So we not only need to ignore enabling of the POSTED bit
when the timer is requested, but also disable Posted mode if errata is present.
[1] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/285744.aspx
[2] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/270632.aspx
[3] http://www.spinics.net/lists/linux-omap/msg81770.html
Cc: stable@vgerk.kernel.org
Reported-by: Russ Dill <russ.dill@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Allow creation and mounting of devtmpfs, which is used
by OpenEmbedded root filesystems among others.
- Enable CPUidle for the ux500, it has been accidentally
disabled due to a Kconfig change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=jJ0N
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, Ux500 defconfig patches for the v3.13 rc series:
- Allow creation and mounting of devtmpfs, which is used
by OpenEmbedded root filesystems among others.
- Enable CPUidle for the ux500, it has been accidentally
disabled due to a Kconfig change.
* tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: u8500_defconfig: add missing cpuidle option
u8500_defconfig: allow creation and mounting of devtmpfs
- Restore platform data for the (e)MMC/SD controllers, so they can
pins and special flags properly like before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=VO2C
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, Ux500 fixes for the v3.13 series:
- Restore platform data for the (e)MMC/SD controllers, so they can
pins and special flags properly like before.
* tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
Revert "ARM: ux500: Stop passing MMC's platform data for Device Tree boots"
Revert "ARM: ux500: Remove AUXDATA relating to SDI (MMC) clock-name bindings"
This reverts commit 49c129519a.
The special settings for the SD/MMC card parameters that are not
yet fully agreed upon how to encode into the device tree went missing
with this commit. We need to first put it into the device tree,
and then remove the platform data.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit ce16feb851.
This commit stopped tying down the name of the MMC/SD devices, but these
names are used in the pin control table, so the MMC/SD cards stopped
working.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the commit d3f2950f2a, the option
ARM_U8500_CPUIDLE was added to the Kconfig but not reflected in the
default config file, hence the cpuidle driver is no longer enabled
since this commit.
Enable it again by adding the missing option in the default config file.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables CONFIG_DETTMPFS and CONFIG_DEVTMPFS_MOUNT
flags for u8500 based devices.
In this way it's possible to create a tmpfs/ramfs already in the
early stages of the boot, allowing programs like udev/mdev to
populate the /dev directory.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We do not have REGULATOR_FIXED selected if no boards are selected
and we boot with device tree. This can cause various devices to
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.
Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
MCPM code was changed in commit 0de0d64675 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Commit 14fd8ed0a7 ("ARM: mvebu: Relocate Armada 370/XP PCIe
device tree nodes") relocated the PCIe controller DT nodes one level
up in the Device Tree, to reflect a more correct representation of the
hardware introduced by the mvebu-mbus Device Tree binding.
However, while most of the boards were properly adjusted accordingly,
the Armada 370 DB board was left unchanged, and therefore, PCIe is
seen as not enabled on this board. This patch fixes that by moving the
PCIe controller node one level-up in armada-370-db.dts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 14fd8ed0a7 "ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes"
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP provides a mechanism called "virtual CPU registers" or
"per-CPU register banking", to access the per-CPU registers of the
current CPU, without having to worry about finding on which CPU we're
running. CPU0 has its registers at 0x21800, CPU1 at 0x21900, CPU2 at
0x21A00 and CPU3 at 0x21B00. The virtual registers accessing the
current CPU registers are at 0x21000.
However, in the Device Tree node that provides the register addresses
for the coherency unit (which is responsible for ensuring coherency
between processors, and I/O coherency between processors and the
DMA-capable devices), a mistake was made: the CPU0-specific registers
were specified instead of the virtual CPU registers. This means that
the coherency barrier needed for I/O coherency was not behaving
properly when executed from a CPU different from CPU0. This patch
fixes that by using the virtual CPU registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: e60304f8cb "arm: mvebu: Add hardware I/O Coherency support"
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The asynchronous aborts are generally fatal for the kernel but they can
be masked via the pstate A bit. If a system error happens while in
kernel mode, it won't be visible until returning to user space. This
patch enables this kind of abort early to help identifying the cause.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the spin-table SMP booting method, secondary CPUs poll a location
passed in the DT. The foundation-v8.dts file doesn't have this memory
reserved and there is a risk of Linux using it before secondary CPUs are
started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit f27dde8dee (sched: Add NEED_RESCHED to the preempt_count)
introduced the use of bit 31 in preempt_count for obscure scheduling
purposes.
This causes interrupts taken from EL0 to hit the (open coded) BUG when
this flag is flipped while handling the interrupt (we compare the
values before and after, and kill the kernel if they are different).
The fix is to stop messing with the preempt count entirely, as this
is already being dealt with in the generic code (irq_enter/irq_exit).
Tested on a dual A53 FPGA running cyclictest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Git commit 9e34f2686bb088b211b6cac8772e1f644c6180f8
"s390/mm,tlb: tlb flush on page table upgrade fixup" removed the
exception handler for the asce-type exception. This is incorrect
as the user-copy with MVCOS can cause asce-type exceptions in
the kernel if a user pointer is too large. Those need to be
handled with do_no_context to branch to the fixup in the
user-copy code.
The simplest fix for this problem is to call do_dat_exception for
asce-type excpetions, as there is no vma for the address the code
will handle the exception correctly.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git commit 4f37a68cda
"s390: Use direct ktime path for s390 clockevent device" makes use
of the CLOCK_EVT_FEAT_KTIME clockevent option to avoid the delta
calculation with ktime_get() in clockevents_program_event and the
get_tod_clock() in s390_next_event. This is based on the assumption
that the difference between the internal ktime and the hardware
clock is reflected in the wall_to_monotonic delta. But this is not
true, the ntp corrections are applied via changes to the tk->mult
multiplier and this is not reflected in wall_to_monotonic.
In theory this could be solved by using the raw monotonic clock
but it is simpler to switch back to the standard clock delta
calculation.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Switch to the improved update_vsyscall interface that provides
sub-nanosecond precision for gettimeofday and clock_gettime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When translating a user space address, the address must be checked against
the ASCE limit of the process. If the address is larger than the maximum
address that is reachable with the ASCE, an ASCE type exception must be
generated.
The current code simply ignored the higher order bits. This resulted in an
address wrap around in user space instead of an exception in user space.
Cc: stable@vger.kernel.org # v3.9+
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Chen originally proposed this as "right thing to do" however I
actually ran into this when building perf tools. Some of the utils
include unistd.h as well as linux/unistd.h. Since -I includes kernel
headers too, we end up including the ARC unistd.h twice, leading to
redefinition nwarnings.
------------------>8-------------------
CC bench/sched-pipe.o
In file included from ~/kernel/arch/arc/include/uapi/asm/unistd.h:21:0,
from ~/kernel/include/uapi/linux/unistd.h:7,
from bench/sched-pipe.c:24:
~/kernel/include/uapi/asm-generic/unistd.h:889:0: error: "__NR_fcntl64"
redefined [-Werror]
#define __NR_fcntl64 __NR3264_fcntl
^
In file included from
~/gnu/arc-linux-uclibc/sys-include/sys/syscall.h:24:0,
from bench/../perf.h:112,
from bench/sched-pipe.c:13:
~/gnu/arc-linux-uclibc/include/bits/sysnum.h:761:0: note: this is the
location of the previous definition
------------------>8-------------------
Verified that make headers_install works fine with this.
Suggested-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: David Howells <dhowells@redhat.com>
for tmp_part->header.name:
it is "Terminating null required only for names < 12 chars".
so need to limit the %.12s for it in printk
additional info:
%12s limit the width, not for the original string output length
if name length is more than 12, it still can be fully displayed.
if name length is less than 12, the ' ' will be filled before name.
%.12s truly limit the original string output length (precision)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In a recent patch:
commit c13f20ac48
Author: Michael Neuling <mikey@neuling.org>
powerpc/signals: Mark VSX not saved with small contexts
We fixed an issue but an improved solution was later discussed after the patch
was merged.
Firstly, this patch doesn't handle the 64bit signals case, which could also hit
this issue (but has never been reported).
Secondly, the original patch isn't clear what MSR VSX should be set to. The
new approach below always clears the MSR VSX bit (to indicate no VSX is in the
context) and sets it only in the specific case where VSX is available (ie. when
VSX has been used and the signal context passed has space to provide the
state).
This reverts the original patch and replaces it with the improved solution. It
also adds a 64 bit version.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When CONFIG_SPARSEMEM_VMEMMAP option is used in kernel, makedumpfile fails
to filter vmcore dump as it fails to do vmemmap translations. So far
dump filtering on ppc64 never had to deal with vmemmap addresses seperately
as vmemmap regions where mapped in zone normal. But with the inclusion of
CONFIG_SPARSEMEM_VMEMMAP config option in kernel, this vmemmap address
translation support becomes necessary for dump filtering. For vmemmap adress
translation, few kernel symbols are needed by dump filtering tool. This patch
adds those symbols to vmcoreinfo, which a dump filtering tool can use for
filtering the kernel dump. Tested this changes successfully with makedumpfile
tool that supports vmemmap to physical address translation outside zone normal.
[ Removed unneeded #ifdef as suggested by Michael Ellerman --BenH ]
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen reported a failure in an allyesconfig build.
CONFIG_CPU_LITTLE_ENDIAN=y gets set but his toolchain is not
new enough to support little endian. We really want to
default to a big endian build; Ben suggested using a choice
which defaults to CPU_BIG_ENDIAN.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently if I cross build TAGS or cscope from x86 I get this:
% make ARCH=powerpc TAGS
gcc-4.8.real: error: unrecognized command line option ‘-mbig-endian’
GEN TAGS
%
I'm not setting CROSS_COMPILE= as logically I shouldn't need to and I
haven't needed to in the past when building TAGS or cscope. Also, the
above completess correct as the error is not fatal to the build.
This was caused by:
commit d72b080171
Author: Ian Munsie <imunsie@au1.ibm.com>
powerpc: Add ability to build little endian kernels
The below fixes this by testing for the -mbig-endian option before
adding it.
I've not done the same thing in the little endian case as if
-mlittle-endian doesn't exist, we probably want to fail quickly as you
probably have an old big endian compiler.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Do not build the phy fixup unless CONFIG_PHYLIB is enabled.
Other than not being useful it is also not possible to link
the code under this condition as phy_register_fixup_for_id(),
mdiobus_read() and mdiobus_write() are absent.
arch/arm/mach-shmobile/built-in.o: In function `lager_ksz8041_fixup':
board-lager.c:(.text+0xb8): undefined reference to `mdiobus_read'
board-lager.c:(.text+0xd4): undefined reference to `mdiobus_write'
arch/arm/mach-shmobile/built-in.o: In function `lager_init':
board-lager.c:(.init.text+0xafc): undefined reference to `phy_register_fixup_for_id'
This problem was introduced by 48c8b96f21
("ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup")
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
mv78260 flavour of Marvell Armada XP SoC has 3 PCIe units. The
two first units are both x4 and quad x1 capable. The third unit
is only x4 capable. This patch fixes mv78260 .dtsi to reflect
those capabilities.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.10.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Various Marvell datasheets advertise second PCIe unit of mv78230
flavour of Armada XP as x4/quad x1 capable. This second unit is in
fact only x1 capable. This patch fixes current mv78230 .dtsi to
reflect that, i.e. makes 1.0 the second interface (instead of 2.0
at the moment). This was successfully tested on a mv78230-based
ReadyNAS 2120 platform with a x1 device (FL1009 XHCI controller)
connected to this second interface.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.10.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
And in flush_hugetlb_page(), don't check whether vma is NULL after
we've already dereferenced it.
This was found by Dan using static analysis as described here:
https://lists.ozlabs.org/pipermail/linuxppc-dev/2013-November/113161.html
We currently get away with this because the callers that currently pass
NULL for vma seem to be 32-bit-only (e.g. highmem, and
CONFIG_DEBUG_PGALLOC in pgtable_32.c) Hugetlb is currently 64-bit only,
so we never saw a NULL vma here.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
These lines were inoperative for four years, which puts some doubt into
their importance, and it's possible the fixed version will regress, but
at the very least they should be removed instead.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit beb2dc0a7a breaks the MPC8xx which
seems to not support using mfspr SPRN_TBRx instead of mftb/mftbu
despite what is written in the reference manual.
This patch reverts to the use of mftb/mftbu when CONFIG_8xx is
selected.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
If CONFIG_ALTIVEC is enabled for CoreNet64, and if we also
select CONFIG_E{5,6}500_CPU this may introduce -mcpu=e500mc64
into $CFLAGS. But Altivec option not allowed with e500mc64,
then some compiling errors occur like this:
CC arch/powerpc/lib/xor_vmx.o
arch/powerpc/lib/xor_vmx.c:1:0: error: AltiVec not supported in this target
make[1]: *** [arch/powerpc/lib/xor_vmx.o] Error 1
make: *** [arch/powerpc/lib] Error 2
So we should restrict e500mc64 in altivec scenario.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull DRM fixes from Dave Airlie:
"I was going to leave this until post -rc1 but sysfs fixes broke
hotplug in userspace, so I had to fix it harder, otherwise a set of
pulls from intel, radeon and vmware,
The vmware/ttm changes are bit larger but since its early and they are
unlikely to break anything else I put them in, it lets vmware work
with dri3"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
drm/sysfs: fix hotplug regression since lifetime changes
drm/exynos: g2d: fix memory leak to userptr
drm/i915: Fix gen3 self-refresh watermarks
drm/ttm: Remove set_need_resched from the ttm fault handler
drm/ttm: Don't move non-existing data
drm/radeon: hook up backlight functions for CI and KV family.
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/radeon/cik: Add macrotile mode array query
drm/radeon/cik: Return backend map information to userspace
drm/vmwgfx: Make vmwgfx dma buffers prime aware
drm/vmwgfx: Make surfaces prime-aware
drm/vmwgfx: Hook up the prime ioctls
drm/ttm: Add a minimal prime implementation for ttm base objects
drm/vmwgfx: Fix false lockdep warning
drm/ttm: Allow execbuf util reserves without ticket
drm/i915: restore the early forcewake cleanup
...
Pull ARM fixes from Russell King:
"Some small fixes for this merge window, most of them quite self
explanatory - the biggest thing here is a fix for the ARMv7 LPAE
suspend/resume support"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7894/1: kconfig: select GENERIC_CLOCKEVENTS if HAVE_ARM_ARCH_TIMER
ARM: 7893/1: bitops: only emit .arch_extension mp if CONFIG_SMP
ARM: 7892/1: Fix warning for V7M builds
ARM: 7888/1: seccomp: not compatible with ARM OABI
ARM: 7886/1: make OABI default to off
ARM: 7885/1: Save/Restore 64-bit TTBR registers on LPAE suspend/resume
ARM: 7884/1: mm: Fix ECC mem policy printk
ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE
ARM: 7882/1: mm: fix __phys_to_virt to work with 64 bit phys_addr_t in BE case
ARM: 7881/1: __fixup_smp read of SCU config should do byteswap in BE case
ARM: Fix nommu.c build warning
Pull third set of powerpc updates from Benjamin Herrenschmidt:
"This is a small collection of random bug fixes and a few improvements
of Oops output which I deemed valuable enough to include as well.
The fixes are essentially recent build breakage and regressions, and a
couple of older bugs such as the DTL log duplication, the EEH issue
with PCI_COMMAND_MASTER and the problem with small contexts passed to
get/set_context with VSX enabled"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/signals: Mark VSX not saved with small contexts
powerpc/pseries: Fix SMP=n build of rng.c
powerpc: Make cpu_to_chip_id() available when SMP=n
powerpc/vio: Fix a dma_mask issue of vio
powerpc: booke: Fix build failures
powerpc: ppc64 address space capped at 32TB, mmap randomisation disabled
powerpc: Only print PACATMSCRATCH in oops when TM is active
powerpc/pseries: Duplicate dtl entries sometimes sent to userspace
powerpc: Remove a few lines of oops output
powerpc: Print DAR and DSISR on machine check oopses
powerpc: Fix __get_user_pages_fast() irq handling
powerpc/eeh: More accurate log
powerpc/eeh: Enable PCI_COMMAND_MASTER for PCI bridges
There are two code paths how page with pmd page table can be freed:
pmd_free() and pmd_free_tlb().
I've missed the second one and didn't add page table destructor call
there. It leads to leak of page->ptl for pmd page tables, if
dynamically allocated page->ptl is in use.
The patch adds the missed destructor and modifies documentation
accordingly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Tested-by: Andrey Vagin <avagin@openvz.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The davinci_gpio_register() function expects the number of
resources as the second parameter, but sizeof() resources
was passed to it due to which it was causing unexpected
behaviour. This patch fixes the same by passing the
ARRAY_SIZE() of resources.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Just a small pile of fixes for bugs and a few regressions. I'm still
trying to track down a driver load hang on my g33 (which infuriatingly
doesn't happen when loading the module manually after boot), somehow
bisecting loves to go astray on this one :( And there's a (harmless)
locking WARN in the suspend code due to one of Jesse's vlv backlight
rework patches. Otherwise nothing outstanding afaik.
* tag 'drm-intel-fixes-2013-11-20' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix gen3 self-refresh watermarks
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/i915: restore the early forcewake cleanup
Partially revert "drm/i915: tune the RC6 threshold for stability"
drm/i915: flush cursors harder
i915: Use 120MHz LVDS SSC clock for gen5/gen6/gen7
x86/early quirk: use gen6 stolen detection for VLV
drm/i915/dp: set sink to power down mode on dp disable
The VSX MSR bit in the user context indicates if the context contains VSX
state. Currently we set this when the process has touched VSX at any stage.
Unfortunately, if the user has not provided enough space to save the VSX state,
we can't save it but we currently still set the MSR VSX bit.
This patch changes this to clear the MSR VSX bit when the user doesn't provide
enough space. This indicates that there is no valid VSX state in the user
context.
This is needed to support get/set/make/swapcontext for applications that use
VSX but only provide a small context. For example, getcontext in glibc
provides a smaller context since the VSX registers don't need to be saved over
the glibc function call. But since the program calling getcontext may have
used VSX, the kernel currently says the VSX state is valid when it's not. If
the returned context is then used in setcontext (ie. a small context without
VSX but with MSR VSX set), the kernel will refuse the context. This situation
has been reported by the glibc community.
Based on patch from Carlos O'Donell.
Tested-by: Haren Myneni <haren@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit a489043 "Implement arch_get_random_long() based on H_RANDOM" I
broke the SMP=n build. We were getting plpar_wrappers.h via spinlock.h
which breaks when SMP=n.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up until now we have only used cpu_to_chip_id() in the topology code,
which is only used on SMP builds. However my recent commit a4da0d5
"Implement arch_get_random_long/int() for powernv" added a usage when
SMP=n, breaking the build.
Move cpu_to_chip_id() into prom.c so it is available for SMP=n builds.
We would move the extern to prom.h, but that breaks the include in
topology.h. Instead we leave it in smp.h, but move it out of the
CONFIG_SMP #ifdef. We also need to include asm/smp.h in rng.c, because
the linux version skips asm/smp.h on UP. What a mess.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I encountered following issue:
[ 0.283035] ibmvscsi 30000015: couldn't initialize event pool
[ 5.688822] ibmvscsi: probe of 30000015 failed with error -1
which prevents the storage from being recognized, and the machine from
booting.
After some digging, it seems that it is caused by commit 4886c399da
as dma_mask pointer in viodev->dev is not set, so in
dma_set_mask_and_coherent(), dma_set_coherent_mask() is not called
because dma_set_mask(), which is dma_set_mask_pSeriesLP() returned EIO.
While before the commit, dma_set_coherent_mask() is always called.
I tried to replace dma_set_mask_and_coherent() with
dma_coerce_mask_and_coherent(), and the machine could boot again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/wsp/wsp.c: In function ‘wsp_probe_devices’:
arch/powerpc/platforms/wsp/wsp.c:76:3: error: implicit declaration of function ‘of_address_to_resource’ [-Werror=implicit-function-declaration]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit fba2369e6c (mm: use vm_unmapped_area() on powerpc architecture)
has a bug in slice_scan_available() where we compare an unsigned long
(high_slices) against a shifted int. As a result, comparisons against
the top 32 bits of high_slices (representing the top 32TB) always
returns 0 and the top of our mmap region is clamped at 32TB
This also breaks mmap randomisation since the randomised address is
always up near the top of the address space and it gets clamped down
to 32TB.
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If TM is not active there is no need to print PACATMSCRATCH
so we can save ourselves a line.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Machine check exceptions set DAR and DSISR, so print them in our
oops output.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__get_user_pages_fast() may be called with interrupts disabled (see e.g.
get_futex_key() in kernel/futex.c) and therefore should use local_irq_save()
and local_irq_restore() instead of local_irq_disable()/enable().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: <stable@vger.kernel.org> [v3.12]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This clarifies in the log whether the error is a global PHB error
or an individual PE being frozen.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PHB3, we will fail to fetch IODA tables without PCI_COMMAND_MASTER
on PCI bridges. According to one experiment I had, the MSIx interrupts
didn't raise from the adapter without the bit applied to all upstream
PCI bridges including root port of the adapter. The patch forces to
have that bit enabled accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc LE updates from Ben Herrenschmidt:
"With my previous pull request I mentioned some remaining Little Endian
patches, notably support for our new ABI, which I was sitting on
making sure it was all finalized.
The toolchain folks confirmed it now, the new ABI is stable and merged
with gcc, so we are all good. Oh and we actually missed the actual
Kconfig switch for LE so here it is, along with a couple more bug
fixes.
I have more fixes but not related to LE so I'll send them as a
separate pull request tomorrow, let's get this one out of the way.
Note that this supports running user space binaries using the new ABI,
but the kernel itself still needs to be built with the old one. We'll
bring fixes for that after -rc1.
Here's Anton log that goes with this series:
This patch series adds support for the new ABI, LPAR support for
H_SET_MODE and finally adds a kconfig option and defconfig.
ABIv2 support was recently committed to binutils and gcc, and should
be merged into glibc soon. There are a number of very nice
improvements including the removal of function descriptors. Rusty's
kernel patches allow binaries of either ABI to work, easing the
transition"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Wrong DWARF CFI in the kernel vdso for little-endian / ELFv2
powerpc: Add pseries_le_defconfig
powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.
powerpc: Don't use ELFv2 ABI to build the kernel
powerpc: ELF2 binaries signal handling
powerpc: ELF2 binaries launched directly.
powerpc: Set eflags correctly for ELF ABIv2 core dumps.
powerpc: Add TIF_ELF2ABI flag.
pseries: Add H_SET_MODE to change exception endianness
powerpc/pseries: Fix endian issues in pseries EEH code
The ARM architected timer driver doesn't compile without
GENERIC_CLOCKEVENTS selected, so ensure that we select it when building
for a platform that has the timer.
Without this patch, mach-virt fails to build without something like
mach-vexpress also selected.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Uwe reported a build failure when targetting a NOMMU platform with my
recent prefetch changes:
arch/arm/lib/changebit.S: Assembler messages:
arch/arm/lib/changebit.S:15: Error: architectural extension `mp' is
not allowed for the current base architecture
This is due to use of the .arch_extension mp directive immediately prior
to an ALT_SMP(...) instruction. Whilst the ALT_SMP macro will expand to
nothing if !CONFIG_SMP, gas will still choke on the directive.
This patch fixes the issue by only emitting the sequence (including the
directive) if CONFIG_SMP=y.
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull alpha updates from Matt Turner:
"It contains a few fixes and some work from Richard to make alpha
emulation under QEMU much more usable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: Prevent a NULL ptr dereference in csum_partial_copy.
alpha: perf: fix out-of-bounds array access triggered from raw event
alpha: Use qemu+cserve provided high-res clock and alarm.
alpha: Switch to GENERIC_CLOCKEVENTS
alpha: Enable the rpcc clocksource for single processor
alpha: Reorganize rtc handling
alpha: Primitive support for CPU power down.
alpha: Allow HZ to be configured
alpha: Notice if we're being run under QEMU
alpha: Eliminate compiler warning from memset macro
Pull parisc fixes from Helge Deller:
- revert an access_ok() patch which broke 32bit userspace on 64bit
kernels
- avoid a gcc miscompilation in two internal pa_memcpy() functions by
not inlining those
- do not export the definition of SOCK_NONBLOCK via uapi header (fixes
build of audit package)
- depending on the fault type we now correctly report either SIGBUS or
SIGSEGV
- a small fix to not compare a size_t variable for < 0
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: size_t is unsigned, so comparison size < 0 doesn't make sense.
parisc: improve SIGBUS/SIGSEGV error reporting
parisc: break out SOCK_NONBLOCK define to own asm header file
parisc: do not inline pa_memcpy() internal functions
Revert "parisc: implement full version of access_ok()"
Pull AVR32 updates from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: uapi: be sure of "_UAPI" prefix for all guard macros
avr32: add kprobe_ctlblk memory struct
avr32: fix out-of-range jump in large kernels
avr32: setup crt for early panic()
Pull vfs bits and pieces from Al Viro:
"Assorted bits that got missed in the first pull request + fixes for a
couple of coredump regressions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fold try_to_ascend() into the sole remaining caller
dcache.c: get rid of pointless macros
take read_seqbegin_or_lock() and friends to seqlock.h
consolidate simple ->d_delete() instances
gfs2: endianness misannotations
dump_emit(): use __kernel_write(), not vfs_write()
dump_align(): fix the dumb braino
Note that pmds[i] is simply uninitialized at that point...
Granted, it's very hard to hit (you need split page locks *and*
kmalloc(sizeof(spinlock_t), GFP_KERNEL) failing), but the code is
obviously bogus.
Introduced by commit 09ef493985 ("x86: add missed
pgtable_pmd_page_ctor/dtor calls for preallocated pmds")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've finally tracked down why my CR signal-unwind test case still
fails on little-endian. The problem turned to be that the kernel
installs a signal trampoline in the vDSO, and provides a DWARF CFI
record for that trampoline. This CFI describes the save location
for CR:
rsave (70, 38*RSIZE + (RSIZE - CRSIZE))
which is correct for big-endian, but points to the wrong word on
little-endian. This is wrong no matter which ABI.
In addition, for the ELFv2 ABI, we should not only provide a CFI
record for register 70 (cr2), but for all CR fields separately.
Strictly speaking, I guess this would mean providing two separate
vDSO images, one for ELFv1 processes and one for ELFv2 processes (or
maybe playing some tricks with conditional DWARF expressions).
However, having CFI records for the other CR fields in ELFv1 is not
actually wrong, they just will be ignored. So it seems the simplest
fix would be just to always provide CFI for all the fields.
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the little endian support merged, we can add the
CONFIG_CPU_LITTLE_ENDIAN kernel config option.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel doesn't build correctly using the ELFv2 ABI. This patch
ensures that the ELFv1 ABI is used when building a kernel with an
ELFv2 enabled compiler.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For the ELFv2 ABI, the hander is the entry point, not a function descriptor.
We also need to set up r12, and fortunately the fast_exception_return
exit path restores r12 for us so nothing else is required.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No function descriptor, but we set r12 up and set TIF_RESTOREALL as it
normally isn't restored on return from syscall.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We leave it at zero (though it could be 1) for old tasks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Little endian ppc64 is getting an exciting new ABI. This is reflected
by the bottom two bits of e_flags in the ELF header:
0 == legacy binaries (v1 ABI)
1 == binaries using the old ABI (compiled with a new toolchain)
2 == binaries using the new ABI.
We store this in a thread flag, because we need to set it in core
dumps and for signal delivery. Our chief concern is that it doesn't
use function descriptors.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On little endian builds call H_SET_MODE so exceptions have the
correct endianness. We need to reset the endian during kexec
so do that in the MMU hashtable clear callback.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
The timer code for at91rm9200 was already converted some time ago by
Shawn Guo in commit 838a2ae (ARM: use clockevents_config_and_register()
where possible) but because of a rounding issue in the timer core this
resulted in an easily reproducible oops. So it was reverted (commit
b7a8ca5 (ARM: at91: rm9200 fix time support)) which stopped the oops
from happening because min_delta_ns is increased by one in arch code
which stopped from problem from happening.
Now that the timer core problem is fixed (commit a4578ea (clockevents:
Sanitize ticks to nsec conversion)), we can switch back to the
clockevents_config_and_register helper.
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We should not be using jump labels before they were initialized. Push back
the callback to until after jump label initialization.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
For all uapi headers, need use "_UAPI" prefix for its guard macro
(which will be stripped by "scripts/headers_installer.sh").
Also remove redundant files (bitsperlong.h, errno.h, fcntl.h, ioctl.h,
ioctls.h, ipcbuf.h, kvm_para.h, mman.h, poll.h, resource.h, siginfo.h,
statfs.h, and unistd.h) which are already in Kbuild.
Also be sure that all "#endif" only have one empty line above, and each
file has guard macro.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
