o Access on card memory through memory controller (agent)
rather than moving small pci window around. Clean up the
code for moving windows around.
o Restrict memory accesss to 64 bit, currently only firmware
download uses this.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f6eb9b1fc1, "tg3: Add 5717 asic
rev" changed how the rx return ring size operations are done. It
effectively inverts the sense of the previous test, but it failed to
also invert the resulting sizes. This patch corrects that error.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is disabled, netxen has a build failure:
netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'
so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, the network device driver knows what layer-3 address the
device should have. This adds support for the Phonet stack to
automatically request from the driver and add that address to the
network device.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFA_F_DADFAILED flag to denote an IPv6 address that has
failed Duplicate Address Detection, that way tools like
/sbin/ip can be more informative.
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:db8::1/64 scope global tentative dadfailed
valid_lft forever preferred_lft forever
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txq_set_wrr() function in drivers/net/mv643xx_eth.c is
unused, not even referenced under #if 0 or something like that,
which results in a compile-time warning:
drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used
Fix: remove it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).
PHY: mdio@e0102120:00 - Link is Up - 1000/Full
sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
PHY: mdio@e0102120:00 - Link is Down
PHY: mdio@e0102120:00 - Link is Up - 100/Half
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c01fcbd0 [verbose debug info unavailable]
NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
...
The cure is to disable the controller before changing speed/duplex
and enable it afterwards.
Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need ugeth_disable() and ugeth_enable() calls earlier in the
file, so rearrange some code to avoid forward declarations.
The patch doesn't contain any functional changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only valid usage for the bridge frame hooks are by a
GPL components (such as the bridge module).
The kernel should not leave a crack in the door for proprietary
networking stacks to slip in.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And also do a better job of returning proper NET_{RX,XMIT}_ values.
Based on a patch and suggestions by Mark Smith.
This fixes CVE-2009-2903
Reported-by: Mark Smith <lk-netdev@lk-netdev.nosense.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Olavi Niemitalo reported that:
"..., when one process calls sendmsg once to send 43804 bytes of
data and one file descriptor, and another process then calls recvmsg
three times to receive the 16032+16032+11740 bytes, each of those
recvmsg calls returns the file descriptor in the ancillary data. I
confirmed this with strace. The behaviour differs from Linux
2.6.26, where reportedly only one of those recvmsg calls (I think
the first one) returned the file descriptor."
This bug was introduced by a patch from me titled "net: unix: fix inflight
counting bug in garbage collector", commit 6209344f5.
And the reason is, quoting Kalle:
"Before your patch, unix_attach_fds() would set scm->fp = NULL, so
that if the loop in unix_stream_sendmsg() ran multiple iterations,
it could not call unix_attach_fds() again. But now,
unix_attach_fds() leaves scm->fp unchanged, and I think this causes
it to be called multiple times and duplicate the same file
descriptors to each struct sk_buff."
Fix this by introducing a flag that is cleared at the start and set
when the fds attached to the first buffer. The resulting code should
work equivalently to the one on 2.6.26.
Reported-by: Kalle Olavi Niemitalo <kon@iki.fi>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro res_size in drivers/net/dm9000.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the offset of vlan_TCI field in cmd_desc_type0.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in checking dest ip has support before
programming destip addresses.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When new child qdiscs are attached to the mq qdisc, they are actually
attached as root qdiscs to the device queues. The lock selection for
new estimators incorrectly picks the root lock of the existing and
to be replaced qdisc, which results in a use-after-free once the old
qdisc has been destroyed.
Mark mq qdisc instances with a new flag and treat qdiscs attached to
mq as children similar to regular root qdiscs.
Additionally prevent estimators from being attached to the mq qdisc
itself since it only updates its byte and packet counters during dumps.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handles the case when SIOCSIWSCAN specified iw_scan_req.num_channels and
iw_scan_req.channels[].
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oops, a stupid mistake in the original patch which adds coex 3-wire
support. Bluetooth priority gpio needs to be gpio 7.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The preferred module is p54pci which also supports FullMAC
PCI / Cardbus devices. We schedule removal for 2.6.34. Reason
to remove this is no one really is testing prism54 anymore,
and while it works p54pci provides support for the same hardware.
It should be noted I have been told some FullMAC devices may not
have worked with the SoftMAC driver but to date we have yet to
recieve a single bug report regarding this. If there are users
out there please let us know!
Cc: aquilaver@yahoo.com
Cc: linux-kernel@vger.kernel.org
Cc: Dan Williams <dcbw@redhat.com>
Cc: Kai Engert <kengert@redhat.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Tim de Waal<tim.dewaal@yahoo.com>
Cc: Roy Marples <uberlord@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some gcc warnings for switch statements.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for communicating with a Sonics Silicon Backplane through a
SDIO interface, as found in the Nintendo Wii WLAN daughter card.
The Nintendo Wii WLAN card includes a custom Broadcom 4318 chip with
a SDIO host interface.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Sun, 2009-09-06 at 12:26 -0700, Luis R. Rodriguez wrote:
> On Sun, Sep 6, 2009 at 10:59 AM, Joe Perches<joe@perches.com> wrote:
> > On Thu, 2009-09-03 at 15:54 -0700, Luis R. Rodriguez wrote:
> >> I'm pleased to announce the new home page to Atheros Linux wireless drivers:
> >> http://wireless.kernel.org/en/users/Drivers/Atheros
> > Perhaps add this to MAINTAINERS?
> Fine by me, except ath5k and ath9k also have their own respective page
> so those can also be added.
(cc's trimmed and maintainers added)
Perhaps this instead:
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning in the hardware-TKIP code:
drivers/net/wireless/b43/xmit.c:272:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/b43/xmit.c:272:18: expected unsigned short [unsigned] [short] <noident>
drivers/net/wireless/b43/xmit.c:272:18: got restricted unsigned short [usertype] <noident>
The code should work correctly with and without this patch applied.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when QoS-disable is requested, we would leave QoS enabled
in firmware, but only queue frames on one queue.
Change that and also tell firmware about disabled QoS, so it
completely ignores all the QoS parameters. Also don't upload the parameters,
if QoS is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.
After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.
The symptoms of this problem:
- Rate control module always falls back to 1Mbs
- Low throughput when bitrate was fixed
Possible side-effects (not confirmed but highly likely)
- Problems with DHCP
- Broken connections due to lack of probe response
This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix apparent thinko related to RTM_DELADDRLABEL, introduced by commit
2a8cc6c890 ("[IPV6] ADDRCONF: Support
RFC3484 configurable address selection policy table.").
Signed-off-by: Tushar Gohad <tgohad@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function res_size in drivers/net/niu.c is a copy of resource_size in
linux/ioport.h. Remove the function and use resource_size instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCMCIA support works well and is not experimental anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).
This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.
Currently CTL are applied for the FCC group only.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9170 driver needs the defines for conformance test limit groups
and cannot include regd_common.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SSB modinit should not succeed, if busattach failed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the SHM spinlock.
SHM is protected by wl->mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the PIO RX work. It's not needed anymore, because
we can sleep in the threaded interrupt handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the DMA/PIO queue locks. Locking is handled by
wl->mutex now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the TX spinlock and defers TX to a workqueue to allow
locking wl->mutex instead and to allow sleeping for register accesses.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
