PIPE_MBUS_DBOX_CTL was only being programmed when a pipe is being
enabled but that could potentially cause issues as it could have
mismatching values while pipes are being enabled.
So here moving the PIPE_MBUS_DBOX_CTL programming of all pipes to be
executed before the function that enables all pipes, leaving all pipes
with a matching A_CREDIT value.
While at it, also moving it to intel_pm.c as we are trying to reduce
the gigantic size of intel_display.c and intel_pm.c have other MBUS
programing sequences.
v2:
- do not program PIPE_MBUS_DBOX_CTL if pipe will not be active or
when it do not needs modeset
- remove the checks to wait a vblank
v3:
- checking if dbuf state is present in state before using it
v4:
- removing redundant checks
- calling intel_atomic_get_new_dbuf_state instead of
intel_atomic_get_dbuf_state
BSpec: 49213
BSpec: 50343
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220330155724.255226-3-jose.souza@intel.com
There's really no need to maintain these total[] arrays to
track the size of each plane's ddb allocation. We just stick
the results straight into the crtc_state ddb tracking structures.
The main annoyance with all this is the mismatch between
wm_uv vs. ddb_y on pre-icl. If only the hw was consistent in
what it considers the primary source of information we could
avoid some of the uglyness. But since that is not the case
we need a bit of special casing for planar formats.
v2: Keep the ddb entry zeroed when the plane is disabled
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-5-ville.syrjala@linux.intel.com
Handle the plane relative data rate in exactly the same
way as we already handle the real data rate. Ie. pre-calculate
it during intel_plane_atomic_check_with_state(), and assign/clear
it for the Y plane as needed. This should guarantee that the
tracking is 100% consistent, and makes me have to think less
when the same apporach is used by both types of data rate.
We might even want to consider replacing the relative
data rate with the real data rate entirely, but it's not
clear if that will produce less optimal plane ddb
allocations. So for now lets keep using the current approach.
v2: Rebase due to async flip wm optimization
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-4-ville.syrjala@linux.intel.com
Let's store the plane allocation in a manner which more closely
matches how the hw operates. That is, we store the packed/CbCr
ddb in one struct, and the Y ddb in another. Currently we're
storing packed/Y in one struct, CbCr in the other.
This also works pretty well for icl+ where the UV plane is
the main plane and the Y plane is subservient to it. Although
in this case we do not even use ddb_y as we do the ddb allocation
in terms of hw planes.
v2: Rebase
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303191207.27931-2-ville.syrjala@linux.intel.com
For modern platforms the spec explicitly states that a
SAGV block time of zero means that SAGV is not supported.
Let's extend that to all platforms. Supposedly there should
be no systems where this isn't true, and it'll allow us to:
- use the same code regardless of older vs. newer platform
- wm latencies already treat 0 as disabled, so this fits well
with other related code
- make it a bit more clear when SAGV is used vs. not
- avoid overflows from adding U32_MAX with a u16 wm0 latency value
which could cause us to miscalculate the SAGV watermarks on tgl+
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309164948.10671-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Tile4 in bspec format is 4K tile organized into
64B subtiles with same basic shape as for legacy TileY
which will be supported by Display13.
v2: - Moved Tile4 associating struct for modifier/display to
the beginning(Imre Deak)
- Removed unneeded case I915_FORMAT_MOD_4_TILED modifier
checks(Imre Deak)
- Fixed I915_FORMAT_MOD_4_TILED to be 9 instead of 12
(Imre Deak)
v3: - Rebased patch on top of new changes related to plane_caps.
- Added static assert to check that PLANE_CTL_TILING_YF
matches PLANE_CTL_TILING_4(Nanley Chery)
- Fixed naming and layout description for Tile 4 in drm uapi
header(Nanley Chery)
v4: - Extracted drm_fourcc changes to separate patch(Nanley Chery)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220118115544.15116-3-stanislav.lisovskiy@intel.com
Registers that exist within the MCH BAR and are mirrored into the GPU's
MMIO space are a good candidate to separate out into their own header.
For reference, the mirror of the MCH BAR starts at the following
locations in the graphics MMIO space (the end of the MCHBAR range
differs slightly on each platform):
* Pre-gen6: 0x10000
* Gen6-Gen11 + RKL: 0x140000
v2:
- Create separate patch to swtich a few register definitions to be
relative to the MCHBAR mirror base.
- Drop upper bound of MCHBAR mirror from commit message; there are too
many different combinations between various platforms to list out,
and the documentation is spotty for the older pre-gen6 platforms
anyway.
Bspec: 134, 51771
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220215061342.2055952-2-matthew.d.roper@intel.com
Apparently I totally fumbled the loop condition when I
removed the ARRAY_SIZE() stuff from the dbuf slice config
lookup. Comparing the loop index with the active_pipes bitmask
is utter nonsense, what we want to do is check to see if the
mask is zero or not.
Note that the code actually ended up working correctly despite
the fumble, up until commit eef1739544 ("drm/i915: Allow
!join_mbus cases for adlp+ dbuf configuration") when things
broke for real.
Cc: stable@vger.kernel.org
Fixes: 05e8155afe ("drm/i915: Use a sentinel to terminate the dbuf slice arrays")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220207132700.481-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Catch-up with 5.17-rc2 and trying to align with drm-intel-gt-next
for a possible topic branch for merging the split of i915_regs...
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In terms of async flip optimization we don't to allocate
extra ddb space, so lets skip it.
v2: - Extracted min ddb async flip check to separate function
(Ville Syrjälä)
- Used this function to prevent false positive WARN
to be triggered(Ville Syrjälä)
v3: - Renamed dg2_need_min_ddb to need_min_ddb thus making
it more universal.
- Also used DISPLAY_VER instead of IS_DG2(Ville Syrjälä)
- Use rate = 0 instead of just setting extra = 0, thus
letting other planes to use extra ddb and avoiding WARN
(Ville Syrjälä)
v4: - Renamed needs_min_ddb as s/needs/use/ to match
the wm0 counterpart(Ville Syrjälä)
- Added plane->async_flip check to use_min_ddb(now
passing plane as a parameter to do that)(Ville Syrjälä)
- Account for use_min_ddb also when calculating total data rate
(Ville Syrjälä)
v5:
- Use for_each_intel_plane_on_crtc instead of for_each_intel_plane_id
to get plane->async_flip check and account for all planes(Ville Syrjälä)
- Fix line wrapping(Ville Syrjälä)
- Set plane data rate conditionally, avoiding on redundant assignment
(Ville Syrjälä)
- Removed redundant whitespace(Ville Syrjälä)
- Handle use_min_ddb case in skl_plane_relative_data_rate instead of
icl_get_total_relative_data_rate(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124090653.14547-2-stanislav.lisovskiy@intel.com
This optimization allows to achieve higher perfomance
during async flips.
For the first async flip we have to still temporarily
switch to sync flip, in order to reprogram plane
watermarks, so this requires taking into account
old plane state's do_async_flip flag.
v2: - Removed redundant new_plane_state->do_async_flip
check from needs_async_flip_wm_override condition
(Ville Syrjälä)
- Extract dg2_async_flip_optimization to separate
function(Ville Syrjälä)
- Check for plane->async_flip instead of plane_id
(Ville Syrjälä)
v3: - Rename "needs_async_flip_wm_override" to
"intel_plane_do_async_flip" and move all the required
checks there (Ville Syrjälä)
- Rename "dg2_async_flip_optimization" to
"use_minimal_wm0_only" (Ville Syrjälä)
v4: - Swap new/old_crtc_state in intel_plane_do_async_flip
argument list(Ville Syrjälä)
- Use plane->base.dev to grab i915 pointer in
intel_plane_do_async_flip(Ville Syrjälä)
- Remove const modifier from plane parameter in
use_minimal_wm0_only(Ville Syrjälä)
- Swap also new/old_crtc_state at intel_plane_do_async_flip
call site(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124094929.31722-1-stanislav.lisovskiy@intel.com
Sometimes we might need to change the way we calculate
watermarks, based on which particular plane it is calculated
for. Thus it would be convenient to pass plane struct to those
functions.
v2: Pass plane instead of plane_id
v3: Do not pass plane to skl_cursor_allocation(Ville Syrjälä)
v4: - Make intel_crtc_get_plane static again(Ville Syrjälä)
- s/cursor_plane/plane(Ville Syrjälä)
- Pass plane to skl_compute_wm_* instead of plane_id(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124090653.14547-2-stanislav.lisovskiy@intel.com
