The H_INT_ESB hcall() is used to issue a load or store to the ESB page
instead of using the MMIO pages. This can be used as a workaround on
some HW issues. The OS knows that this hcall should be used on an
interrupt source when the ESB hcall flag is set to 1 in the hcall
H_INT_GET_SOURCE_INFO.
To maintain the frontier between the xive frontend and backend, we
introduce a new xive operation 'esb_rw' to be used in the routines
doing memory accesses on the ESBs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It will be required later by the H_INT_ESB hcall.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is the framework for using XIVE in a PowerVM guest. The support
is very similar to the native one in a much simpler form.
Each source is associated with an Event State Buffer (ESB). This is a
two bit state machine which is used to trigger events. The bits are
named "P" (pending) and "Q" (queued) and can be controlled by MMIO.
The Guest OS registers event (or notifications) queues on which the HW
will post event data for a target to notify.
Instead of OPAL calls, a set of Hypervisors call are used to configure
the interrupt sources and the event/notification queues of the guest:
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (PQ bits) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines to which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification config associated with the
queue, only unconditional notification for the moment. Reset is
performed with a queue size of 0 and queueing is disabled in that
case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the partition's interrupt exploitation structures to
their initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure sure all
notifications have reached their queue.
As for XICS, the XIVE interface for the guest is described in the
device tree under the "interrupt-controller" node. A couple of new
properties are specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), also called rings, for the User level and
for the Guest OS level. Only the Guest OS level is taken into
account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the interrupt numbers ranges assigned to the guest. These are
allocated using a simple bitmap.
and also :
- "/ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use.
Tested with a QEMU XIVE model for pseries and with the Power hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Architecturally we should apply a 0x400 offset for these. Not doing
it will break future HW implementations.
The offset of 0 is supposed to remain for "triggers" though not all
sources support both trigger and store EOI, and in P9 specifically,
some sources will treat 0 as a store EOI. But future chips will not.
So this makes us use the properly architected offset which should work
always.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XIVE interrupt controller is the new interrupt controller
found in POWER9. It supports advanced virtualization capabilities
among other things.
Currently we use a set of firmware calls that simulate the old
"XICS" interrupt controller but this is fairly inefficient.
This adds the framework for using XIVE along with a native
backend which OPAL for configuration. Later, a backend allowing
the use in a KVM or PowerVM guest will also be provided.
This disables some fast path for interrupts in KVM when XIVE is
enabled as these rely on the firmware emulation code which is no
longer available when the XIVE is used natively by Linux.
A latter patch will make KVM also directly exploit the XIVE, thus
recovering the lost performance (and more).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup pr_xxx("XIVE:"...), don't split pr_xxx() strings,
tweak Kconfig so XIVE_NATIVE selects XIVE and depends on POWERNV,
fix build errors when SMP=n, fold in fixes from Ben:
Don't call cpu_online() on an invalid CPU number
Fix irq target selection returning out of bounds cpu#
Extra sanity checks on cpu numbers
]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
