Update the host's SAS ports if there is change in port id or phys. If the
port id is changed, then the driver updates it. If some phys are
enabled/disabled during reset, then driver updates them in STL.
Check for the responding expander devices and update the device handle if
it got changed. Register the expander with STL if it got added during reset
and unregister the expander device if it got removed during reset.
[mkp: include fix for zeroday warning]
Link: https://lore.kernel.org/r/20220804131226.16653-15-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the following helper functions:
- Get the device's sas address by reading corresponding device's Device
page0
- Get the expander object from expander list based on expander's handle
- Get the target device object from target device list based on device's
sas address
- Get the expander device object from expander list based on expanders's
sas address
- Get hba port object from hba port table list based on port's port id
Link: https://lore.kernel.org/r/20220804131226.16653-7-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver to track cumulative pending large data size at the controller
level and at the throttle group level. When one of the values meet or
exceed the controller's firmware-determined high threshold value, then the
driver will divert future selective I/O to the firmware. Once both
controller level and at the throttle group level cumulative pending large
data size reach controller's firmware determined low threshold value, then
the driver will stop diverting I/Os to the firmware.
Link: https://lore.kernel.org/r/20220708195020.8323-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for management applications to send an MPI3 Encapsulated NVMe
passthru command to the NVMe devices attached to an Avenger controller.
Since the NVMe drives are exposed as SCSI devices by the controller, the
standard NVMe applications cannot be used to interact with the drives and
the command sets supported are also limited by the controller firmware.
Special handling is required for MPI3 Encapsulated NVMe passthru commands
for PRP/SGL setup in the commands.
Link: https://lore.kernel.org/r/20220429211641.642010-8-sumit.saxena@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].
This code was transformed with the help of Coccinelle:
(next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch)
@@
identifier S, member, array;
type T1, T2;
@@
struct S {
...
T1 member;
T2 array[
- 0
];
};
UAPI and wireless changes were intentionally excluded from this patch
and will be sent out separately.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/78
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
During controller reset, the driver tries to flush all the pending firmware
event works from worker queue that are queued prior to the reset. However,
if any work is waiting for device addition/removal operation to be
completed at the SML, then a deadlock is observed. This is due to the
controller reset waiting for the device addition/removal to be completed
and the device/addition removal is waiting for the controller reset to be
completed.
To limit this deadlock, continue with the controller reset handling without
canceling the work which is waiting for device addition/removal operation
to complete at SML.
Link: https://lore.kernel.org/r/20220210095817.22828-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the io_uring interface in I/O-polled mode.
This feature is disabled in the driver by default. To enable the feature, a
module parameter "poll_queues" has to be set with the desired number of
polling queues.
When the feature is enabled, the driver reserves a certain number of
operational queue pairs for the poll_queues either from the available queue
pairs or creates additional queue pairs based on the operational queue
availability.
The Polling queues will have corresponding IRQ and ISR functions as similar
to default queues. However, the IRQ line is disabled by the driver for
poll_queues.
Link: https://lore.kernel.org/r/20211220141159.16117-22-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IOC sends a Prepare for Reset Event to the host to prepare for a Soft
Reset. This event data has two reason codes:
1. Start - The host is expected to gracefully quiesce all I/O within
approximately 1 second.
2. Abort - The IOC is requesting to abort a previous Prepare for Reset
Event request. Normal I/O may be resumed.
Link: https://lore.kernel.org/r/20211220141159.16117-20-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhance driver to gracefully handle discrepancies in certain key data sizes
between firmware update operations as mentioned below:
- The driver displays an error message and marks the controller as
unrecoverable if the firmware reports ReplyFrameSize that is greater
than the current ReplyFrameSize.
- If the firmware reports ReplyFrameSize greater than the current
ReplyFrameSize then the driver uses the current ReplyFrameSize while
copying the reply messages.
- The driver displays an error message and marks the controller as
unrecoverable if the firmware reports MaxOperationalReplyQueues less
than the currently allocated operational reply queues count.
- If the firmware reports MaxOperationalReplyQueues that is greater than
the currently allocated operational reply queue count then the driver
ignores the new increased value and uses the previously allocated number
of operational queues only.
- If the firmware reports MaxDevHandle greater than the previously used
MaxDevHandle value after a reset then the driver re-allocates the
'device remove pending bitmap' buffer with the newer size using
krealloc().
Link: https://lore.kernel.org/r/20211220141159.16117-18-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect asynchronous reset that occurred in the firmware by polling for
reset history bit of IOC status register is set and if that bit is set,
then the driver waits for the controller to become ready and then
re-initializes the controller.
Also reduce the time driver is waiting for the controller to acknowledge
the reset action after issuing a specific reset action to the
controller. The wait time is reduced from 510 seconds to 30 seconds. If the
controller didn't acknowledge a specific reset action within the time
interval then the driver marks the controller as unrecoverable instead of
retrying two more times prior to giving up.
Link: https://lore.kernel.org/r/20211220141159.16117-17-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver marks the controller as unrecoverable if there is an
asynchronous reset or fault during the initialization, reinitialization
post reset, and OS resume.
Enhance driver to retry the initialization, re-initialization, and resume
sequences for a maximum of 3 times if the controller became faulty or
asynchronously reset due to a firmware activation during the initialization
sequence.
Link: https://lore.kernel.org/r/20211220141159.16117-15-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save snapdump and fault the controller with the given reason code if it is
already not in the fault or not in asynchronous reset. This ensures that
soft reset is issued from the watchdog thread. This will also be used to
handle initialization time faults/resets/timeout as in those cases
immediate soft reset invocation is not required.
Link: https://lore.kernel.org/r/20211220141159.16117-12-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS4 Controller firmware exposes the SES devices in Managed PCIe Switch
as a PCIe Device Type SCSI Device
(MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SCSI_DEVICE).
Driver is enhanced to handle this device type by:
- Exposing the device to the upper layers and
- Not updating any hardware sectors & virtual boundary settings as these
settings are needed only for NVMe devices.
Link: https://lore.kernel.org/r/20211220141159.16117-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
