remove_and_add_spares() assumes that failed devices have been hot-removed
from the array. Removal is skipped in the 'blocked' case so do not count a
device in this state as 'spare'.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
handle_stripe will take no action on a stripe when waiting for userspace
to unblock the array, so do not report completed sectors.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The original STRIPE_OP_IO removal patch had the following hunk:
- for (i = conf->raid_disks; i--; ) {
+ for (i = conf->raid_disks; i--; )
set_bit(R5_Wantwrite, &sh->dev[i].flags);
- if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
- sh->ops.count++;
- }
However it appears the hunk became broken after merging:
- for (i = conf->raid_disks; i--; ) {
+ for (i = conf->raid_disks; i--; )
set_bit(R5_Wantwrite, &sh->dev[i].flags);
set_bit(R5_LOCKED, &dev->flags);
s.locked++;
- if (!test_and_set_bit(STRIPE_OP_IO, &sh->ops.pending))
- sh->ops.count++;
- }
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some dma drivers need to call spin_lock_bh in their device_issue_pending
routines. This change avoids:
WARNING: at kernel/softirq.c:136 local_bh_enable_ip+0x3a/0x85()
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock. However there are three places where
the list is walked without any locking. If a reconfig happens at this
time, havoc (and oops) can ensue.
So use RCU to protect these accesses:
- wrap them in rcu_read_{,un}lock()
- use list_for_each_entry_rcu
- add to the list with list_add_rcu
- delete from the list with list_del_rcu
- delay the 'free' with call_rcu rather than schedule_work
Note that export_rdev did a list_del_init on this list. In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe. It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
- after unbind_rdev_from_array, in which case the delete has
already been done,
- after bind_rdev_to_array fails, in which case the delete isn't needed.
- before the device has been put on a list at all (e.g. in
add_new_disk where reading the superblock fails).
- and in autorun devices after a failure when the device is on a
different list.
So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.
Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates). In these cases rcu is not needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Open isn't the only thing that increments ->active. e.g. reading
/proc/mdstat will increment it briefly. So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Also, change the type of the size parameter from unsigned long long to
sector_t and rename it to num_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The checks in overlaps() expect all parameters either in block-based
or sector-based quantities. However, its single caller passes two
rdev->data_offset arguments as well as two rdev->size arguments, the
former being sector counts while the latter are measured in 1K blocks.
This could cause rdev_size_store() to accept an invalid size from user
space. Fix it by passing only sector-based quantities to overlaps().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
- used strict_strtoull in place of simple_strtoull
- use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
- don't adjust mddev->size to fit, rather reject changes which make
rdev->size smaller than mddev->size
Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing. But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that. The previous way invites confusion.
Signed-off-by: NeilBrown <neilb@suse.de>
Rename it to sb_start to make sure all users have been converted.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
As BLOCK_SIZE_BITS is 10 and
MD_NEW_SIZE_SECTORS(2 * x) = 2 * NEW_SIZE_BLOCKS(x),
the return value of calc_dev_sboffset() doubles. Fix up all three
callers accordingly.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Number of sectors is the preferred unit for sizes of raid devices,
so change calc_dev_size() so that it returns this unit instead of
the number of 1K blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Changing the internal representations of sizes of raid devices
from 1K blocks to sector counts (512B units) is desirable because
it allows to get rid of many divisions/multiplications and unnecessary
casts that are present in the current code.
This patch is a first step in this direction. It replaces the old
1K-based "size" argument of update_size() by "num_sectors" and
fixes up its two callers.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
do_md_stop check the number of active users before allowing the array
to be stopped.
Two problems:
1/ it assumes the request is coming through an open file descriptor
(via ioctl) so it allows for that. This is not always the case.
2/ it doesn't do the check it the array hasn't been activated.
This is not good for cases when we use an inactive array to hold
some devices in a container.
Signed-off-by: Neil Brown <neilb@suse.de>
The current code copies a signed int from user space, converts it to
unsigned and passes the unsigned value to find_rdev_nr() which expects
a signed value. Simply pass the signed value from user space directly.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
If alloc_page() fails, ENOMEM is a more suitable error value
than EINVAL.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
The only caller of sb_equal() tests the return value against
zero, so it's OK to return the negated return value of memcmp().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Neil Brown <neilb@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
tun: Persistent devices can get stuck in xoff state
xfrm: Add a XFRM_STATE_AF_UNSPEC flag to xfrm_usersa_info
ipv6: missed namespace context in ipv6_rthdr_rcv
netlabel: netlink_unicast calls kfree_skb on error path by itself
ipv4: fib_trie: Fix lookup error return
tcp: correct kcalloc usage
ip: sysctl documentation cleanup
Documentation: clarify tcp_{r,w}mem sysctl docs
netfilter: nf_nat_snmp_basic: fix a range check in NAT for SNMP
netfilter: nf_conntrack_tcp: fix endless loop
libertas: fix memory alignment problems on the blackfin
zd1211rw: stop beacons on remove_interface
rt2x00: Disable synchronization during initialization
rc80211_pid: Fix fast_start parameter handling
sctp: Add documentation for sctp sysctl variable
ipv6: fix race between ipv6_del_addr and DAD timer
irda: Fix netlink error path return value
irda: New device ID for nsc-ircc
irda: via-ircc proper dma freeing
sctp: Mark the tsn as received after all allocations finish
...
The scenario goes like this. App stops reading from tun/tap.
TX queue gets full and driver does netif_stop_queue().
App closes fd and TX queue gets flushed as part of the cleanup.
Next time the app opens tun/tap and starts reading from it but
the xoff state is not cleared. We're stuck.
Normally xoff state is cleared when netdev is brought up. But
in the case of persistent devices this happens only during
initial setup.
The fix is trivial. If device is already up when an app opens
it we clear xoff state and that gets things moving again.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a XFRM_STATE_AF_UNSPEC flag to handle the AF_UNSPEC behavior for
the selector family. Userspace applications can set this flag to leave
the selector family of the xfrm_state unspecified. This can be used
to to handle inter family tunnels if the selector is not set from
userspace.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
So, no need to kfree_skb here on the error path. In this case we can
simply return.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a07f5f508a "[IPV4] fib_trie: style
cleanup", the changes to check_leaf() and fn_trie_lookup() were wrong - where
fn_trie_lookup() would previously return a negative error value from
check_leaf(), it now returns 0.
Now fn_trie_lookup() doesn't appear to care about plen, so we can revert
check_leaf() to returning the error value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: William Boughton <bill@boughton.de>
Acked-by: Stephen Heminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kcalloc is supposed to be called with the count as its first argument and
the element size as the second.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduced version of the spelling cleanup patch.
Take out the confusing language in tcp_frto, and organize the
undocumented values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some of the defaults and attempt to clarify some language.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum reported a crash in kmem_cache_alloc():
BUG: unable to handle kernel paging request at da87d000
IP: [<c01991c7>] kmem_cache_alloc+0xc7/0xe0
*pde = 28180163 *pte = 1a87d160
Oops: 0002 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Pid: 3850, comm: grep Not tainted (2.6.26-rc9-00059-gb190333 #5)
EIP: 0060:[<c01991c7>] EFLAGS: 00210203 CPU: 0
EIP is at kmem_cache_alloc+0xc7/0xe0
EAX: 00000000 EBX: da87c100 ECX: 1adad71a EDX: 6b6b6b6b
ESI: 00200282 EDI: da87d000 EBP: f60bfe74 ESP: f60bfe54
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
and analyzed it:
"The register %ecx looks innocent but is very important here. The disassembly:
mov %edx,%ecx
shr $0x2,%ecx
rep stos %eax,%es:(%edi) <-- the fault
So %ecx has been loaded from %edx... which is 0x6b6b6b6b/POISON_FREE.
(0x6b6b6b6b >> 2 == 0x1adadada.)
%ecx is the counter for the memset, from here:
memset(object, 0, c->objsize);
i.e. %ecx was loaded from c->objsize, so "c" must have been freed.
Where did "c" come from? Uh-oh...
c = get_cpu_slab(s, smp_processor_id());
This looks like it has very much to do with CPU hotplug/unplug. Is
there a race between SLUB/hotplug since the CPU slab is used after it
has been freed?"
Good analysis.
Yeah, it's possible that a caller of kmem_cache_alloc() -> slab_alloc()
can be migrated on another CPU right after local_irq_restore() and
before memset(). The inital cpu can become offline in the mean time (or
a migration is a consequence of the CPU going offline) so its
'kmem_cache_cpu' structure gets freed ( slab_cpuup_callback).
At some point of time the caller continues on another CPU having an
obsolete pointer...
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel Bugzilla #11063 points out that on some architectures (e.g. x86_32)
exec'ing an ELF without a PT_GNU_STACK program header should default to an
executable stack; but this got broken by the unlimited argv feature because
stack vma is now created before the right personality has been established:
so breaking old binaries using nested function trampolines.
Therefore re-evaluate VM_STACK_FLAGS in setup_arg_pages, where stack
vm_flags used to be set, before the mprotect_fixup. Checking through
our existing VM_flags, none would have changed since insert_vm_struct:
so this seems safer than finding a way through the personality labyrinth.
Reported-by: pageexec@freemail.hu
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up __migrate_task(): to just have separate "done" and "fail"
cases, instead of that "out" case with random error behavior.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PREEMPT_RCU without HOTPLUG_CPU is broken. The rcu_online_cpu is called
to initially populate rcu_cpu_online_map with all online CPUs when the
hotplug event handler is installed, and also to populate the map with
CPUs as they come online. The former case is meant to happen with and
without HOTPLUG_CPU, but without HOTPLUG_CPU, the rcu_offline_cpu
function is no-oped -- while it still gets called, it does not set the
rcu CPU map.
With a blank RCU CPU map, grace periods get to tick by completely
oblivious to active RCU read side critical sections. This results in
free-before-grace bugs.
Fix is obvious once the problem is known. (Also, change __devinit to
__cpuinit so the function gets thrown away on !HOTPLUG_CPU kernels).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ Nick is my personal hero of the day - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the long awaited ftrace.txt. It explains in quite detail how to
use ftrace and the various tracers.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The stack-glue merge changed the way we use flags in dlmglue in that we now
use the fs/dlm equivalents. Unfortunately, a merge error left the new flock
code only partially updated. This took a while to show up though, because
the lock level constants are actually identical between o2dlm and fs/dlm.
The *_CONVERT and *_NOQUEUE flags have different values though, which is
eventually causing a crash in flags_to_o2dlm().
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
When chainiv postpones requests it never calls their completion functions.
This causes symptoms such as memory leaks when IPsec is in use.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add ioremap_default(), which gives a sane mapping without worrying about
type conflicts.
Use it in /dev/mem read in place of ioremap(), as with ioremap(),
any mapping of the region (other than UC_MINUS) will cause a conflict
and failure of /dev/mem read.
Should address the vbetest failure reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=11057
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I think we may have a race between try_to_wake_up() and
migrate_live_tasks() -> move_task_off_dead_cpu() when the later one
may end up looping endlessly.
Interrupts are enabled on other CPUs when migration_call(CPU_DEAD, ...) is
called so we may get a race between try_to_wake_up() and
migrate_live_tasks() -> move_task_off_dead_cpu(). The former one may push
a task out of a dead CPU causing the later one to loop endlessly.
Heiko Carstens observed:
| That's exactly what explains a dump I got yesterday. Thanks for fixing! :)
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: miaox@cn.fujitsu.com
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
