PCM1681 can be controlled via I2C, SPI or in bootstrap mode (no control mode). This code add
support only for I2C mode.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The adau1701 driver was removed from SND_SOC_ALL_CODECS in commit commit ee8c7e9
("ASoC: Remove adau1701 from SND_SOC_ALL_CODECS due to Sigma dependency") due
to the dependency on the SigmaDSP firmware loader which was only available on a
limited set of platforms. This was fixed quite some time ago in commit 40216ce7
("ASoC: Move SigmaDSP firmware loader to ASoC") though, so we can add the driver
back again to SND_SOC_ALL_CODECS.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The main function of the option is to enable compile testing. There is
still an option since COMPILE_TEST is intended to enable selection of
extra drivers rather than forcing them on.
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4554 is very simple DA/AD converter which has no setting register.
Note that it has hard coded asymmetric data format
playback : SND_SOC_DAIFMT_RIGHT_J
capture : SND_SOC_DAIFMT_LEFT_J
This driver has single DAI and doesn't have set_fmt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the ALC5640 codec driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is useless if both SPI and I2C are not configured.
Thus don't build this driver if both SPI and I2C are not configured.
This patch silences below build warning if both SPI and I2C are not configured.
CC sound/soc/codecs/adav80x.o
sound/soc/codecs/adav80x.c:842:12: warning: 'adav80x_bus_probe' defined but not used [-Wunused-function]
sound/soc/codecs/adav80x.c:863:12: warning: 'adav80x_bus_remove' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
to support HDMI on CSR SiRFprimaII and atlasVI, we need one more HDMI pseudo
codec, rather than add a new driver, we can make omap HDMI codec common for
other SoCs as well. then the omap-hdmi codec becomes a generic HDMI pseudo-
codec as HDMI audio features depend on HDMI specification not on SoCs.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Kconfig symbol SND_SOC_OF_SIMPLE got removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC
Multi-Component Support"). But that commit missed one instance. Remove
it now, together with the prompt it has effectively hidden ever since.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a driver for TI's TA5086 6-channel PWM processor.
This chip has a very unusual register layout, specifically because the
registers are of unequal size, and multi-byte registers require bulk
writes to take effect. Regmap does not support these kind of mappings.
Currently, the driver does not touch any of the registers >= 0x20, so
it doesn't matter, because the register map is mapped to an 8-bit array.
In case more features will be added in the future that require access
to higher registers, the entire regmap H/W I/O routines have to be
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a driver for Asahi Kasei's AK5386 Single-ended 24-Bit 192kHz
delta-sigma ADC. The device has no control port interface but an
optional RESET/PDN GPIO pin.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
A few more updates from the past week - a new driver from Dialog and
some small fixes and tweaks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ivD5
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.9-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Final updates for v3.9
A few more updates from the past week - a new driver from Dialog and
some small fixes and tweaks.
This patch adds support for the Dialog DA7213 audio codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix these two compile errors on s390 which does not have HAS_IOPORT
nor GENERIC_HARDIRQS:
sound/pci/lx6464es/lx6464es.c: In function ‘snd_lx6464es_free’:
sound/pci/lx6464es/lx6464es.c:565:2: error: implicit declaration of function ‘ioport_unmap’
sound/soc/codecs/wm8903.c: In function ‘wm8903_set_pdata_irq_trigger’:
sound/soc/codecs/wm8903.c:1954:9: error: implicit declaration of function ‘irq_get_irq_data’
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the max98090 codec prototype driver.
It supports Headphone only at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regmap-mmio instead of open-coding caching and register accessors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit add a sound codec driver for Silicon Laboratories 476x
series of AM/FM radio chips.
Signed-off-by: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog semiconductor's DA9055 audio codec.
This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM0010 is a compact digital signal processor that has been
highly optimised for low-power audio applications. Extensive memory
resources and core optimisation allow the device to manage all audio
processing algorithms efficiently and autonomously, while the host
processor sleeps or performs other tasks.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds the audio CODEC driver for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Dialog DA732x audio codecs.
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add codec-driver for ST-Ericsson AB8500 mixed-signal ASIC.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: Support TI Isabelle Audio driver
The Isabelle Audio IC is a complete low power high fidelity CODEC with integrated
ADCs, DACs, decimation and interpolation filters, PLL, and power providers. This
device supports 2 analog and 2 digital microphone channels, a mono earpiece driver,
stereo class G headphone drivers with ultra low power and best SNR in the industry,
stereo Class D speaker drivers, and 2 high performance Line drivers.
The below patch is a basic driver code for TI Isabelle audio codec. The
functionalities like headset detection, etc., will be included incrementally
in the up-coming patches.
Signed-off-by: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Cirrus Logic CS42L52 Low Power Stereo Codec
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ML26124-01HB/ML26124-02GD is 16bit monaural audio CODEC which has high
resistance to voltage noise. On chip regulator realizes power supply rejection
ratio be over 90dB so more than 50dB is improved than ever. ML26124-01HB/
ML26124-02GD can deliver stable audio performance without being affected by noise
from the power supply circuit and peripheral components. The chip also includes
a composite video signal output, which can be applied to various portable device
requirements. The ML26124 is realized these functions into very small package
the size is only 2.56mm x 2.46mm therefore can be construct high quality sound
system easily.
ML26124-01HB is 25pin WCSP package; ML26124-02GD is 32pin WQFN package.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently SND_SOC_JZ4740_CODEC depends on SOC_JZ4740 but SOC_JZ4740 is not
defined in any Kconfig. Thus the codec driver will not be built when select
"Build all ASoC CODEC drivers".
(Unless it is selected by SND_JZ4740_SOC_QI_LB60).
Remove the dependency with SOC_JZ4740, then this code driver can be built when
select "Build all ASoC CODEC drivers".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Cirrus Logic CS42L73 low power stereo
codec.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver implements basic functionality, using I²C for the control
channel.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is currently named "TVL" instead of "TLV".
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation. This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch adds support for the Analog Devices ADAU1373 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert TWL6040 CODEC driver into a TWL6040 MFD child, it implies
that MFD-level operations like register accesses, clock setting
and power management are done through MFD APIs, not directly by
CODEC driver anymore. To avoid conflicts with the other MFD child,
vibrator registers are skipped in CODEC driver.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Sigma code is in drivers/firmware which is only included on a very
small subset of architectures and so ends up breaking the build on
others. There's a pending patch to make the directory build as standard
but it's not merged yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAU1701 SigmaDSP.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A driver for the AK4641 codec used in iPAQ hx4700 and Glofiish M800
among others.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1250-EV1 Springbank audio I/O module for the Wolfson Glenfarclas
reference platform provides a simple audio I/O with an independant clock
domain, intended to simulate cellular modem and bluetooth subsystems
within the platform.
The card supports some limited GPIO based control but this is currently not
implemented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8915 is an ultra low power mobile CODEC designed for smartphones,
featuring a mixture of digital and analogue I/O with flexible mixing
options and advanced low power accessory detection functionality in a
compact package.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The ssm2602 codec has a SPI interface as well as I2C, so add the simple
bit of glue to make it usable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the MAX98095 CODEC driver.
Signed-off-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AD73311 codec does not use I2C, so don't require it in Kconfig.
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
These changes are needed to keep up with the changes in the
MFD core and V4L2 parts of the wl1273 FM radio driver.
Use function pointers instead of exported functions for I2C IO.
Also move all preprocessor constants from the wl1273.h to
include/linux/mfd/wl1273-core.h.
Also update the year in the copyright statement.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds ASoC support for the MAX9850 codec with headphone
amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPM
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a codec driver for the dfbmcs320 bluetooth module, which is used
on the neo1973 boards.
The patch also modifies the neo1937_wm8753 sound board driver to use the new
driver instead of registering the bluetooth DAI manually.
Previously there was a name mismatch between the bluetooth DAI and the bluetooth
DAI link and the sound card was not instantiated, with this patch the issue is
no longer present and sound support works again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch moves the code for the lm4857 AMP from the neo1973_wm8753 sound
board driver to its own module.
The lm4857 is a generic AMP IC and not specific to the neo1973.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added support for CS4271 codec to ASoC.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8991 is a highly integrated ultra-low power hi-fi CODEC designed for
handsets rich in multimedia features such as GPS, mobile TV, digital audio
playback and gaming.
This driver was originally written by Graeme Gregory and has been maintained
out of tree by Mark Brown and Dimitris Papastamos.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These changes are needed to keep up with the changes in the
MFD core and V4L2 parts of the wl1273 FM radio driver.
Use function pointers instead of exported functions for I2C IO.
Also move all preprocessor constants from the wl1273.h to
include/linux/mfd/wl1273-core.h.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This codec is to be used by the DMIC driver to
control the DMIC codec. This driver will be used on future
implementations of the DMIC driver to support codec specific
features.
At this time, the codec driver just registers the codec DAI.
Signed-off-by: David Lambert <dlambert@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds the sn95031 asoc codec driver. This driver currently
supports only playback. Capture and jack detection to be added later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8995 is a digital audio hub CODEC designed for smartphones.
The current driver supports most of the basic functionality of the
WM8995.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8737 is a low power, flexible stereo ADC designed for portable
applications. This driver supports most of the functionality of the
WM8737, though some features such as the ALC are not yet implemented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8770 is a high performance, multi-channel audio
codec. The WM8770 is ideal for surround sound processing
applications for home hi-fi, automotive and other audio
visual equipment.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Include alc5623.c in SND_SOC_ALL_CODECS when dependencies are met.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
