module_spi_driver eliminates module_init and module_exit
calls and makes the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rework the mxs_ssp_timeout() function to make it a bit more readable
and hopefully less error prone. Also, have only one successful exit
from the function and one failing exit instead of two.
Finally, discard the udelay() from this function altogether, as this
tightloop is quick enough it's pointless.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver checks the length of transfer to be made and based
on this information, either chooses to transfer data via DMA or
PIO. Decrement this border further to gain better performace eg.
during SPI flash writes.
Empiric measurement shows that this gives extra 3kB/s write speed
with a M25P80 flash clocked at 40MHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The transfer function incremented (struct spi_message)->actual_length
unconditionally, even if the transfer failed. Rectify this by incrementing
this only if transfer succeeded.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When doing long continuous transfer, eg. from SPI flash via /dev/mtd,
the driver dies. This is caused by a bug in the DMA chaining. Rework
the DMA transfer code so that this issue does not happen any longer.
This involves proper allocation of correct amount of sg-list members.
Also, this means proper creation of DMA descriptors. There is actually an
important catch to this, the data transfer descriptors must be interleaved
with PIO register write descriptor, otherwise the transfer stalls. This
can be done in one descriptor, but due to the limitation of the DMA API,
it's not possible.
It turns out that in order for the SPI DMA to properly support
continuous transfers longer than 65280 bytes, there are some very
important parts that were left out from the documentation about about
the PIO transfer that is used.
Firstly, the XFER_SIZE register is not written with the whole length
of a transfer, but is written by each and every chained descriptor
with the length of the descriptors data buffer.
Next, unlike the demo code supplied by FSL, which only writes one PIO
word per descriptor, this does not apply if the descriptors are chained,
since the XFER_SIZE register must be written. Therefore, it is essential
to use four PIO words, CTRL0, CMD0, CMD1, XFER_SIZE. CMD0 and CMD1 are
written with zero, since they don't apply. The DMA programs the PIO words
in an incrementing order, so four PIO words.
Finally, unlike the demo code supplied by FSL, the SSP_CTRL0_IGNORE_CRC
must not be set during the whole transfer, but it must be set only on the
last descriptor in the chain.
Lastly, this code lends code from drivers/mtd/nand/omap2.c, which solves
trouble when the buffer supplied to the DMA transfer was vmalloc()'d. So
with this patch, it's safe to use /dev/mtdblockX interface again.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds DT bindings to the spi-gpio driver and some
documentation about how to use it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The spi-gpio driver currently assumes the chipselect gpio number is
stored in ->controller_data of the device's static board information.
In devicetree environments, this information is unavailable and has to
be derived from the DT node.
This patch moves the gpio storage to the controller's private data so
the DT bindings can easily build upon the driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Removes use of the DaVinci EDMA private DMA API and replaces
it with use of the DMA engine API.
Signed-off-by: Matt Porter <mporter@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which results in
device memory being freed. The remove function accesses the freed memory after
the call to spi_unregister_master(), _and_ it calls spi_master_put on the freed
memory.
Acquire a reference to the SPI master device and release it after cleanup is
complete (with the existing spi_master_put) to solve the problem.
Also, the device subsystem ensures that the remove function is only called once,
and resets device driver data to NULL. Remove the unnecessaary calls to
platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Suspend and resume functions call spi_master_get() without matching
spi_master_put(). The extra references are unnecessary and cause subsequent
module unload attempts to fail. Drop the calls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which results in
device memory being freed. An extra call to spi_master_put is unnecessary
and results in an access to free memory. Drop it.
Also, the device subsystem resets device driver data to NULL after the call to
the remove function returns, so there is no need to do it here.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call to spi_unregister_master() in the device remove function frees device
memory, and with it any device local data. However, device local data is still
accessed after the call to spi_unregister_master().
Acquire a reference to the SPI master device and release it after cleanup is
complete to solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which results in
device memory being freed. The remove function accesses the freed memory after
the call to spi_unregister_master(), _and_ it calls spi_master_put on the freed
memory.
Acquire a reference to the SPI master device and release it after cleanup is
complete (with the existing spi_master_put) to solve the problem.
Also, the device subsystem ensures that the remove function is only called once,
and resets device driver data to NULL. Remove the respective check and drop the
unnecessaary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The init_completion() call does reinit not only the variable carrying
the flag that the completion finished, but also initialized the
waitqueue associated with the completion. On the contrary, the
INIT_COMPLETION() call only reinits the flag.
In case there was anything still stuck in the waitqueue, subsequent call
to init_completion() would be able to create possible race condition. This
patch uses the proper function and moves init_completion() into .probe() call
of the driver, to be issued only once.
Note that such scenario is impossible, since two threads can never enter the
mxs_spi_txrx_dma(), since whole this section is protected by mutex in SPI core.
This by no means allows this issue to exit though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Restart the SSP block in case the SSP transfer failed in any way.
The block hung in some cases otherwise.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull MIPS fixes from Ralf Baechle:
"Random fixes across the MIPS tree. The two hotspots are several bugs
in the module loader and the ath79 SOC support; also noteworthy is the
restructuring of the code to synchronize CPU timers across CPUs on
startup; the old code recently ceased to work due to unrelated
changes.
All except one of these patches have sat for a significant time in
linux-next for testing."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: pci-ar724x: avoid data bus error due to a missing PCIe module
MIPS: Malta: Delete duplicate PCI fixup.
MIPS: ath79: don't hardcode the unavailability of the DSP ASE
MIPS: Synchronize MIPS count one CPU at a time
MIPS: BCM63xx: Fix SPI message control register handling for BCM6338/6348.
MIPS: Module: Deal with malformed HI16/LO16 relocation sequences.
MIPS: Fix race condition in module relocation code.
MIPS: Fix memory leak in error path of HI16/LO16 relocation handling.
MIPS: MTX-1: Add udelay to mtx1_pci_idsel
MIPS: ath79: select HAVE_CLK
MIPS: ath79: Use correct IRQ number for the OHCI controller on AR7240
MIPS: ath79: Fix number of GPIO lines for AR724[12]
MIPS: Octeon: Fix broken interrupt controller code.
If the I2C bus master driver does not support the required functionality,
the driver returns -ENODEV. This causes a silent probe failure without error
message. Since the device has to be explicitly instantiated, and the user
should know the correct bus, this event really reflects an error condition.
Replace error return value with -EINVAL to trigger an error message showing
that the probe function failed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the driver, link it into the kbuild system and provide device tree
binding documentation.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/4292/
Signed-off-by: John Crispin <blogic@openwrt.org>
This patch adds device tree support to the spi-pl022 driver.
Based on the initial patch by Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the ability for the driver to control the chip select directly.
This enables independence from cs_control callbacks. Configurable via
platform_data, to be extended as DT in the following patch.
Based on the initial patch by Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver adds support for NXP SC18IS602/603 I2C to SPI bus bridge.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call to spi_unregister_master() in the device remove function frees device
memory, and with it any device local data. However, device local data is still
accessed after the call to spi_unregister_master().
Acquire a reference to the SPI master device and release it after cleanup is
complete to solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call to spi_unregister_master() in the device remove function frees device
memory, and with it any device local data. However, device local data is still
accessed after the call to spi_unregister_master().
Acquire a reference to the SPI master device and release it after cleanup is
complete to solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master is
complete; it reduces the device reference count to zero, which results in
device memory being freed. An extra call to spi_master_put is unnecessary
and results in an access to free memory.
At the same time, since the call to spi_unregister_master results in device
memory being freed, it must no longer be accessed afterwards.
To fix both problems, call spi_master_get to get an extra reference to the
device, and call spi_master_put only after the last access to device data.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call to spi_master_put() is needed to free device memory. It must be called
after spi_alloc_master, and must only be called after the device memory is no
longer used.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master
is complete; it reduces the device reference count to zero, which results in
device memory being freed. An extra call to spi_master_put is unnecessary
and results in an access to free memory. Drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At remove we shouldnt be using the autosuspend timeout as we are
calling pm_runtime_disable immediately after.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call the pm_runtime functions directly making room for possible
pm optimisations. Also the runtime functions aren't just about
enabling and disabling of clocks though it does enable clocks also.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the macro MOD_REG_BIT instead make the bit field modifications
directly. This deletes a branch operation in cases where the the set
is predecided. While at it optimise two sequential bit clear in one step.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Grant is still away so another pull request with some fairly minor
fixes, the most notable of which are several fixes for some common error
patterns with the reference counting spi_master_get/put do.
-
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8RgT
-----END PGP SIGNATURE-----
Merge tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"Grant is still away so another pull request with some fairly minor
fixes, the most notable of which are several fixes for some common
error patterns with the reference counting spi_master_get/put do."
* tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions
spi: spi-coldfire-qspi: Drop extra spi_master_put in device remove function
spi/pl022: fix spi-pl022 pm enable at probe
spi/bcm63xx: Ensure that memory is freed only after it is no longer used
spi: omap2-mcspi: Fix the error handling in probe
spi/s3c64xx: Add missing static storage class specifiers
Remove the call of platform_set_drvdata(pdev, NULL) as they are not
needed anymore.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of having to define the match table to NULL if CONFIG_OF isn't
set, use the of_match_ptr() macro which will do this for us.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the deprecated master->transfer with transfer_one_message()
and allow the SPI subsystem handle all the queuing of messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These parts will be used by the MXS SPI driver too.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is slightly reworked version of the SPI driver.
Support for DT has been added and it's been converted
to queued API.
Based on previous attempt by:
Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Suspend and resume functions call spi_master_get() without matching
spi_master_put(). The extra references are unnecessary and cause
subsequent module unload attempts to fail, so drop the calls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master is
complete; it reduces the device reference count to zero, which and results in
device memory being freed. The subsequent call to spi_master_put is unnecessary
and results in an access to free memory. Drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
amba drivers does not need to enable pm runtime at probe.
amba_probe already enables pm runtime.
This rids this warning in the ux500 boot log:
ssp-pl022 ssp0: Unbalanced pm_runtime_enable!
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().
Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The call to spi_unregister_master() in the device remove function frees device
memory, and with it any device local data. However, device local data is still
accessed after the call to spi_unregister_master().
Acquire a reference to the SPI device and release it after cleanup is complete
to solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jaswinder Singh <jaswinder.singh@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The kfree() is taken care of by the spi core (spi_master_release() function)
that is called once the last reference to the underlying struct device has
been released. So the driver need not call kfree.
Also the put was missed in some of the error handling fix the same.
There by fixing the missing device_put in some of the error paths.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Silences the following sparse warnings:
drivers/spi/spi-s3c64xx.c:1482:32: warning:
symbol 's3c2443_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1489:32: warning:
symbol 's3c6410_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1495:32: warning:
symbol 's5p64x0_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1501:32: warning:
symbol 's5pc100_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1508:32: warning:
symbol 's5pv210_spi_port_config' was not declared. Should it be static?
drivers/spi/spi-s3c64xx.c:1515:32: warning:
symbol 'exynos4_spi_port_config' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/spi/spi-omap2-mcspi.c: In function 'omap2_mcspi_probe':
drivers/spi/spi-omap2-mcspi.c:1118: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This prepares *of_device_id.data becoming const. Without this change the
following warning would occur:
drivers/spi/spi-imx.c: In function spi_imx_probe:
drivers/spi/spi-imx.c:814:24: warning: assignment discards const qualifier from pointer target type [enabled by default]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
Remove the private DMA API implementation from spi-omap2-mcspi.c,
making it use entirely the DMA engine API.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA engine support to the OMAP SPI driver. This supplements the
private DMA API implementation contained within this driver, and the
driver can be independently switched at build time between using DMA
engine and the private DMA API for the transmit and receive sides.
Tested-by: Shubhrajyoti <shubhrajyoti@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Since Grant is even more specacularly busy than usual for the time being
I've been collecting SPI patches for him for this release - probably
things will revert back to Grant before the next release. There's
nothing too exciting here, mostly it's simple driver specific stuff:
- Add spi: to the modaliases of SPI devices to provide namespacing.
- A driver for AD-FMCOMMS1-EBZ.
- DT binding for Orion.
- Fixes and cleanups for i.MX, PL0022, OMAP and bitbang drivers.
There may be a few more fixes I've missed, people keep sending me new
things.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQD+gTAAoJEBus8iNuMP3diecP/j88CTuSVi2C9LQ6irty2q6y
62eLoR5m5J9zqqRlsFLkerxuanlwyD0WPR4B86SZMr/TQbXkLtmdVyQwSieyMfnN
4HSrFQawCnVANoBrvnKa1vHfP4ouBStXIZa5v/iSAC4tN4K/wVGUvl6Kral5+ktC
5BRwcEdcrVR4KnD74i7ombopM/hl6fRdNS+TwgfXlGwGFHPYbHOa+aJZnGUORWfw
30jrKLap8cTGLDTFQ+Lu8WPzap+RuGlMSWGhXlYrivKNepvpt/WEMhJnfJ/ADLqO
ASGe3C69xGTF6YRETSoH5+1VZjRhf+S9y/nV5gkQZKtDDGez5iFmCGZtv/m87u6/
nIuTICa7QjI9bvP9novq0h6EUwURyL4dtdC4VI3IedIpgFiKGxz3J63YJLsIc7tH
5jXPJAkyU/yj23eDywftYZskK3iNYOthB2VO3JPcmGQRXeMWDvTPXXJBcOy5fvW0
aOmE+vXINiQnmddBBNIuhPGRlJUGSpHLaioz+H2+unrNPHjQnv+CSHt7YuYwjTGp
IFFwVSUK6r4O+/W7ciKalVQr0bjTM6J3wO0sCqxta1qVoI89RgcM3h3XwXTCb6Ly
0Ywgn+3W71XDiY+L4VvYRTcur2kGB/rmIsIORuqS/FkhR9iuIx7u30d6KmlGR2ak
i+cExj0Qo/pF4TXDw22W
=I2b9
-----END PGP SIGNATURE-----
Merge tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"Since Grant is even more specacularly busy than usual for the time
being I've been collecting SPI patches for him for this release -
probably things will revert back to Grant before the next release.
There's nothing too exciting here, mostly it's simple driver specific
stuff:
- Add spi: to the modaliases of SPI devices to provide namespacing.
- A driver for AD-FMCOMMS1-EBZ.
- DT binding for Orion.
- Fixes and cleanups for i.MX, PL0022, OMAP and bitbang drivers.
There may be a few more fixes I've missed, people keep sending me new
things."
* tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/orion: remove uneeded spi_info
spi/bcm63xx: fix clock configuration selection
spi/orion: add device tree binding
spi/omap2: mark omap2_mcspi_master_setup as __devinit
spi: omap2-mcspi: Fix the below warning
spi: Add AD-FMCOMMS1-EBZ I2C-SPI bridge driver
spi/imx: use gpio_is_valid to determine if a gpio is valid
spi/imx: remove redundant config.speed_hz setting
spi/gpio: start with CS non-active
spi: tegra: use dmaengine based dma driver
spi/pl022: cleanup pl022 header documentation
spi/pl022: enable runtime PM
spi/pl022: delete DB5500 support
spi/pl022: disable port when unused
spi: Add "spi:" prefix to modalias attribute of spi devices
Pull m68knommu arch update from Greg Ungerer:
"Quite a varied set of changes this time.
- A little more merge cleanup, this time the assembler entry code.
- New sub-architecture support for the ColdFire 5251/5253 and 5441x
CPU families.
- Specific clk support code for the ColdFire 520x and 532x CPU
familes.
- Refactoring of the ColdFire GPIO support.
- PCI bus support for some ColdFire CPUS that have PCI hardware (54xx
family). This showed up a few problems with ColdFire cache,
allocating coherent memory and bi-directional DMA support. Fixes
for those too."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68k: allow PCI bus to be enabled for ColdFire m54xx CPUs
m68k: add PCI bus code support for the ColdFire M54xx SoC family
m68k: add IO access definitions to support PCI on ColdFire platforms
m68k: add PCI bus support definitions for the ColdFire M54xx SoC family
m68k: common PCI support definitions and code
m68k: add support for DMA_BIDIRECTIONAL in dma support functions
m68k: fix ColdFire clear cache operation
m68k: use simpler dma_alloc_coherent() for ColdFire CPUs
m68knommu: platform support for 8390 based ethernet used on some boards
m68knommu: Add clk definitions for m532x.
m68knommu: Add clk definitions for m520x.
m68knommu: Add rtc device for m5441x.
m68knommu: add definitions for the third interrupt controller on devices that don't have a third interrupt controller.
m68knommu: Add support for the Coldfire m5441x.
m68knommu: use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1
coldfire-qspi: Add support for the Coldfire 5251/5253.
m68knommu: Add support for the Coldfire 5251/5253
m68knommu: refactor Coldfire GPIO not to require GPIOLIB, eliminate mcf_gpio_chips.
m68k: merge the MMU and non-MMU versions of the entry.S code
m68k: use jbsr to call functions instead of bsrl
...
Clock support is moving to the clk subsystem. These tegra, omap and imx
changes are for code that is still platform specific and not (yet)
part of that subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cvpa
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
This was formerly used to store the tclk value. This is now discovered
using the clk API, rather than pass it as platform data.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are currently using an inferior or equal operator for comparing
the transfer frequency with the clock frequency table. Because of
this, we always end up selecting 20Mhz as a frequency, due to the
inequality transfer hz <= 20 Mhz being always true. Fix this by
reversing the inequality, which is how the comparison should be done.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The external bus unit (EBU) found on the FALCON SoC has spi emulation that is
designed for serial flash access. This driver has only been tested with m25p80
type chips. The hardware has no support for other types of spi peripherals.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: spi-devel-general@lists.sourceforge.net
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3844/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This warning recently appeared with omap2plus_defconfig:
WARNING: drivers/spi/built-in.o(.devinit.text+0x3c4): Section mismatch in reference from the function omap2_mcspi_probe() to the function .init.text:omap2_mcspi_master_setup()
The function __devinit omap2_mcspi_probe() references
a function __init omap2_mcspi_master_setup().
If omap2_mcspi_master_setup is only used by omap2_mcspi_probe then
annotate omap2_mcspi_master_setup with a matching annotation.
The fix is obviously to mark the omap2_mcspi_master_setup function as
__devinit, rather than __init.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dma_map and dma_unmap should have same parameter
passed otherwise we get the below warn.
ks8851 spi1.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x000000009f22]
[ 2.066925] Modules linked in:
[ 2.070312]
[ 2.071929] [<c001c250>] (unwind_backtrace+0x0/0x130) from [<c0043d84>] (warn_slowpath_common+0x4c/0x64)
[ 2.081909] [<c0043d84>] (warn_slowpath_common+0x4c/0x64) from [<c0043e30>] (warn_slowpath_fmt+0x30/0x40)
[ 2.091949] [<c0043e30>] (warn_slowpath_fmt+0x30/0x40) from [<c0293824>] (check_unmap+0x6d0/0x7b0)
[ 2.101348] [<c0293824>] (check_unmap+0x6d0/0x7b0) from [<c02939cc>] (debug_dma_unmap_page+0x64/0x70)
[ 2.111053] [<c02939cc>] (debug_dma_unmap_page+0x64/0x70) from [<c03519a4>] (omap2_mcspi_txrx_dma+0x2d8/0x4fc)
[ 2.121582] [<c03519a4>] (omap2_mcspi_txrx_dma+0x2d8/0x4fc) from [<c03524d8>] (omap2_mcspi_work.clone.4+0xf0/0x290)
[ 2.132537] [<c03524d8>] (omap2_mcspi_work.clone.4+0xf0/0x290) from [<c0352900>] (omap2_mcspi_transfer_one_message+0x288/0x438)
[ 2.144592] [<c0352900>] (omap2_mcspi_transfer_one_message+0x288/0x438) from [<c03503bc>] (spi_pump_messages+0x100/0x160)
[ 2.156127] [<c03503bc>] (spi_pump_messages+0x100/0x160) from [<c006635c>] (kthread_worker_fn+0xac/0x180)
[ 2.166168] [<c006635c>] (kthread_worker_fn+0xac/0x180) from [<c0066578>] (kthread+0x90/0x9c)
[ 2.175140] [<c0066578>] (kthread+0x90/0x9c) from [<c00157fc>] (kernel_thread_exit+0x0/0x8)
[ 2.183898] ---[ end trace d1830ce6e44292f2 ]---
Fix the warn by changing the unmap parameter.
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the I2C-SPI bridge which can be found on the Analog
Devices AD-FMCOMMS1-EBZ board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They have very few users and they're both just doing a single register
write so the advantage of having the macro is a bit limited. An inline
function might make sense but it's as easy to just do the writes directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Saves some error handling and a small amount of code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
No call was being made by the GPIO driver to put the GPIO into output
mode meaning that the calls to gpio_set_value() which were being done
were not valid. A similar issue appears to exist with the DT GPIO
requests but as they appear to be being used for pinmux it's less clear
to me that we want to configure them.
Without this fix Cragganmore systems can't talk to their SPI devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When gpio_request() fails the driver logged the failure but while it'd
try to print an error code in the non-DT case it didn't pass the error
code in so garbage would be logged and in the DT case the error wasn't
logged.
Further, in the non-DT case the error code was then overwritten with -EBUSY
depriving the caller of information and breaking automatic probe deferral
pushing back from the GPIO level. Also reformat the non-DT log message
so it's not word wrapped and we can grep for it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Coldfire 5251/5253 have a QSPI controller. Enable selection of the
coldfire-qspi driver if the M525x is selected.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Use gpio_is_valid() to replace "gpio >= 0" or "gpio < 0".
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The config.speed_hz is just setted at the two lines ahead of it,
obviously we don't need to copy the code to set the config.speed_hz
again. Remove it for a cleanup.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for device based discovery.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The set_level callback in the controller data, which is used to configure
the slave select line, cannot be supported when migrating the driver to
device tree based discovery. Since all the platforms currently use gpio
as the slave select line, this callback can be removed from the
controller data and replaced with call to gpio_set_value in the driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The platform data pointer that is passed to the spi gpio setup functions
is not used. Hence, this parameter is removed from all the spi gpio setup
functions.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Platform data is used to specify controller hardware specific information
such as the tx/rx fifo level mask and bit offset of rx fifo level. Such
information is not suitable to be supplied from device tree. Instead,
it can be moved into the driver data and removed from platform data.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The macro S3C64XX_SPI_ST_TRLCNTZ is not used and hence it is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The chip select line was configured as output with the initial value
being active explicitly. It was later deasserted during
spi_bitbang_setup() without any clock activity in between. So it makes
no sense to activate the device at all and the chip select line can
better start non-active.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI FIFO and memory in
place of legacy Tegra APB DMA.
The new driver is selected if legacy driver is not
selected and new DMA driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
From Stephen Warren <swarren@wwwdotorg.org>:
This branch contains numerous changes required as a baseline in order to
convert Tegra to the common clock framework. The intention was to also
include patches to actually convert Tegra to the common clock framework.
However, those patches appeared late in the kernel cycle and currently
cause regressions on some boards, so were dropped for now.
* 'for-3.6/common-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
mmc: tegra: add clk_prepare/clk_unprepare
i2c: tegra: Add clk_prepare/clk_unprepare
ARM: tegra: add clk_prepare/clk_unprepare
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If we're gonna use runtime PM it's a pretty good idea to actually
enable it in probe() and disable it in remove() too, so it
gets used for real. Up until now we only fooled around with the
reference count.
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This ASIC variant has been deleted from the ARM tree, no need
to keep support around.
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ffbbdd2132
"spi: create a message queueing infrastructure"
Accidentally deleted the logic to disable the port
when unused leading to higher power consumption.
Fix this up.
Cc: stable@kernel.org
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Config operation is separated from request operation in
DMA common operation. Because spi driver can change the
DMA config for every transfer. So this patch is using the
separated DMA config operation.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
1a77b127ae (OMAP : SPI : use devm_* functions) converted the SPI
device controller state to use devm_kzalloc(). Unfortunately, this
is used against an unbound struct device, which results in the
following when the device is bound to its driver:
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/drivers/base/dd.c:257 driver_probe_device+0x78/0x21c()
Modules linked in:
Backtrace:
[<c0017d0c>] (dump_backtrace+0x0/0x10c) from [<c033e208>] (dump_stack+0x18/0x1c) r7:00000000 r6:c01ff28c r5:c040050c r4:00000101
[<c033e1f0>] (dump_stack+0x0/0x1c) from [<c00337ec>] (warn_slowpath_common+0x58/0x70)
[<c0033794>] (warn_slowpath_common+0x0/0x70) from [<c0033828>] (warn_slowpath_null+0x24/0x2c)
[<c0033804>] (warn_slowpath_null+0x0/0x2c) from [<c01ff28c>] (driver_probe_device+0x78/0x21c)
[<c01ff214>] (driver_probe_device+0x0/0x21c) from [<c01ff49c>] (__driver_attach+0x6c/0x90)
[<c01ff430>] (__driver_attach+0x0/0x90) from [<c01fda70>] (bus_for_each_dev+0x58/0x98)
[<c01fda18>] (bus_for_each_dev+0x0/0x98) from [<c01ff0f4>] (driver_attach+0x20/0x28)
[<c01ff0d4>] (driver_attach+0x0/0x28) from [<c01fe2f4>] (bus_add_driver+0xb4/0x230)
[<c01fe240>] (bus_add_driver+0x0/0x230) from [<c01ffb24>] (driver_register+0xac/0x138)
[<c01ffa78>] (driver_register+0x0/0x138) from [<c0215d4c>] (spi_register_driver+0x4c/0x60)
[<c0215d00>] (spi_register_driver+0x0/0x60) from [<c045414c>] (ks8851_init+0x14/0x1c)
[<c0454138>] (ks8851_init+0x0/0x1c) from [<c0008770>] (do_one_initcall+0x9c/0x164)
[<c00086d4>] (do_one_initcall+0x0/0x164) from [<c0436410>] (kernel_init+0x128/0x210)
[<c04362e8>] (kernel_init+0x0/0x210) from [<c0038754>] (do_exit+0x0/0x72c)
---[ end trace 4dcda79f5e89dd84 ]---
ks8851 spi1.0: message enable is 0
ks8851 spi1.0: eth0: revision 0, MAC 08:00:28:01:4d:c6, IRQ 194, has EEPROM
Fix this by partially reverting the original commit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Bug fixes and new features for SPI device drivers. Also move device
tree support code out of drivers/of and into drivers/spi/spi.c where
it makes more sense.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/Ux1
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI changes from Grant Likely:
"Bug fixes and new features for SPI device drivers. Also move device
tree support code out of drivers/of and into drivers/spi/spi.c where
it makes more sense."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi: By default setup spi_masters with 1 chipselect and dynamics bus number
SPI: PRIMA2: use the newest APIs of PINCTRL to fix compiling errors
spi/spi-fsl-spi: reference correct pdata in fsl_spi_cs_control
spi: refactor spi-coldfire-qspi to use SPI queue framework.
spi/omap2-mcspi: convert to the pump message infrastructure
spi/rspi: add dmaengine support
spi/topcliff: use correct __devexit_p annotation
spi: Dont call prepare/unprepare transfer if not populated
spi/ep93xx: clean probe/remove routines
spi/devicetree: Move devicetree support code into spi directory
spi: use module_pci_driver
spi/omap2-mcspi: Trivial optimisation
spi: omap2-mcspi: add support for pm_runtime autosuspend
spi/omap: Remove bus_num usage for instance index
OMAP : SPI : use devm_* functions
spi: omap2-mcspi: convert to module_platform_driver
spi: omap2-mcspi: make it behave as a module
The modalias attribute of spi devices doesn't have the "spi:" prefix
that is used in the UEVENT and in spi device drivers. This patch adds
the prefix so the modprobe can correctly match modules to devices.
Reported-by: David Daney <david.daney@cavium.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trivial simplification. Instead of requiring spi master drivers to
always set the bus number (even when a dynamic number is desired),
this patch modifies spi_alloc_master() to initialize num_chipselect to
1 (because there will always be at least one CS) and bus_num to -1 for
dynamic allocation. This simplifies the code needed to be written for
drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix the compiling errors:
drivers/spi/spi-sirf.c: In function 'spi_sirfsoc_probe':
drivers/spi/spi-sirf.c:563: error: implicit declaration of function 'pinmux_get'
drivers/spi/spi-sirf.c:563: warning: assignment makes pointer from integer without a cast
drivers/spi/spi-sirf.c:568: error: implicit declaration of function 'pinmux_enable'
drivers/spi/spi-sirf.c:602: error: implicit declaration of function 'pinmux_disable'
drivers/spi/spi-sirf.c:603: error: implicit declaration of function 'pinmux_put'
make[3]: *** [drivers/spi/spi-sirf.o] Error 1
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed spi device initialization of dev.parent pointer
to be the master's device pointer instead of his parent.
This introduced a bug in spi-fsl-spi, since its usage of spi device
pointer was not updated accordingly. This was later fixed by commit
5039a86, "spi/mpc83xx: fix NULL pdata dereference bug", but it missed
another spot on fsl_spi_cs_control function where we also need to update
usage of spi device pointer. This change address that.
Cc: stable@vger.kernel.org
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the new SPI queue framework; remove use of workqueue, replace
mcfqspi_transfer with mcfqspi_transfer_one_message, add
mcfqspi_prepare_transfer_hw and mcfqspi_unprepare_transfer_hw, update power
management routines.
Signed-off-by: Steven King <sfking@fdwdc.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the OMAP SPI driver to use the SPI infrastructure
pump message queue.Also fixes the below warning.
master is unqueued, this is deprecated
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
__devexit functions are discarded when CONFIG_HOTPLUG
is not set, so the symbol needs to be referenced carefully.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
