The intent here is to test that "sta_id_r" is a valid pointer. We do
this same test later on in the function.
Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is obviously a small picky thing. The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c11d8f89d3: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Based on a patch created by Ondrej Zary)
In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use to_pci_dev in rt2x00pci_uninitialize to get the allocated irq
as it won't work for platform devices (SoC). Instead, use the irq field
that's already used everywhere else.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.
On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.
Also use the return value of the descriptor setup function.
Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event
with missing cfg80211_disconnected in rndis_wlan_do_link_down_work.
Reported-by: "Rogério Brito" <rbrito@ime.usp.br>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.
As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.
Fix the frame length by removing padding.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As remarked by Sam Ravnborg the spin_lock variable, that has been introduced
in commit 57c8a45664 ("can: Fix SJA1000 command
register writes on SMP systems") has not been initialized properly.
This patch adds the initialization to allow spinlock debugging.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocated memory for IRQs should be freed when releasing the mii_bus
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
viafb: move some include files to include/linux
viafb: Eliminate some global.h references
viafb: get rid of i2c debug cruft
viafb: fold via_io.h into via-core.h
viafb: Fix initialization error paths
viafb: Do not remove gpiochip under spinlock
viafb: make procfs entries optional
viafb: fix proc entry removal
viafb: improve misc register handling
viafb: replace inb/outb
viafb: move some modesetting functions to a seperate file
viafb: unify modesetting functions
viafb: Reserve framebuffer memory for the upcoming camera driver
viafb: Add a simple VX855 DMA engine driver
viafb: Add a simple interrupt management infrastructure
via: Rationalize vt1636 detection
viafb: Introduce viafb_find_i2c_adapter()
via: Do not attempt I/O on inactive I2C adapters
viafb: Turn GPIO and i2c into proper platform devices
viafb: Convert GPIO and i2c to the new indexed port ops
...
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Length field of header was incorrectly set to available payload space
rather than the actual payload size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static per-port,
singleton(!) urb pool).
Also remove changelog header (can be retrieved through git).
Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Private data was not freed on error path in startup.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up read processing logic.
Tested using a cp210x device in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom single-urb write implementation.
Note that this driver still depended on the write callback from the old
generic framework.
Tested against original read processing using a cp210x device in a
loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Right now quirks are printed only when the are manually overriden with
the module parameters. It's not so useful to remind the user that his
parameters are correctly applied; what is useful is to print out the
quirks the user is not aware are being applied.
So let's do the smart thing and print the quirks when they are present.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use pr_foo and dev_foo instead of printk. Maybe US_DEBUG* should be
replaced too.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill private write fifo and use port fifo instead (protected under
port lock).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Use private write fifo to minimise changes to lock handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Note that cypress_m8 has no port write fifo as it has no bulk-out
endpoint.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use bulk_out_size in usb_serial_driver to set urb buffer size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size to avoid any regression in throughput
after replacing the old writing scheme which used dynamic buffers (e.g.
up to 2k).
256b has been determined to be a good choice for several drivers
including ftdi_sio which used to have a more or less identical write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use process_read_urb to implement line status handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (dynamically allocated write
urbs).
Note that I chose to remove the stat module parameter which was supposed
to keep count of the amount of data sent and received, but which has
been broken for three years (since b308e74d9c
"USB: visor driver adapted to new tty buffering" -- bytes_in was
incorrectly updated and was thus always reported as 0).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix memory leak for some devices (Sony Clie 3.5) due to port private
data not being freed on release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo, read and write implementations (single-urb and fifo,
but still maintained list of 256*256b urb buffers per port).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static 16*4k write-urb pool
shared among all ports in system).
Also remove old changelog entries in header (code is now gone, and
these entries can still be retrieved through git).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return immediately from generic process_read_urb if urb is empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An urb transfer buffer is allocated at every open but was never freed.
This driver is a bit of a mess...
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for an olivetti olicard100 HЅDPA usb-stick.
This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.
Signed-off-by: Nils Radtke <lkml@Think-Future.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_find_device was the only one user of match_device, now
it is removed, so remove match_device to fix the compile warning
below reported by Stephen Rothwell:
drivers/usb/core/usb.c:596: warning: 'match_device'
defined but not used
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 7acd72eb85 ("kfifo: rename
kfifo_put... into kfifo_in... and kfifo_get... into kfifo_out..."),
kfifo_out() is marked __must_check, and that causes gcc to produce
lots of warnings like this:
CC drivers/usb/host/fhci-mem.o
In file included from drivers/usb/host/fhci-hcd.c:34:
drivers/usb/host/fhci.h: In function 'cq_get':
drivers/usb/host/fhci.h:520: warning: ignoring return value of 'kfifo_out', declared with attribute warn_unused_result
...
This patch fixes the issue by properly checking the return value.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: stable <stable@kernel.org> [.33 and .34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove cp210x_disconnect which is used to kill traffic although this is
already handled by the generic framework.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to raise dtr/rts in open as this is taken care of by tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamically allocated urb for baudrate changes rather than
unconditionally submitting the port write urb which may already be in
use.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use usb_serial_driver bulk_in_size and bulk_out_size to make sure
buffers of appropriate sizes are allocated in the first place rather than
reallocating them at every open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the user specifies a custom bulk buffer size we get a double free at
port release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1380) fixes a bug in the wakeup settings for EHCI host
controllers. When the controller is suspended, if it isn't enabled
for remote wakeup then we have to turn off all the port wakeup flags.
Disabling PCI PME# isn't good enough, because some systems (Intel)
evidently use alternate wakeup signalling paths.
In addition, the patch improves the handling of the Intel Moorestown
hardware by performing various power-up and power-down delays just
once instead of once for each port (i.e., the delays are moved outside
of the port loops). This requires extra code, but the total delay
time is reduced.
There are also a few additional minor cleanups.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Ondrej Zary <linux@rainbow-software.org>
CC: Alek Du <alek.du@intel.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a bug fix for PHCD (phy clock disable) low power feature:
After PHCD is set, any write to PORTSC register is illegal, so when
resume ports, clear PHCD bit first.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Our virtual xHCI device can have as many ports as we like - I've tested
this patch with 31.
Signed-off-by: William Gulland <wgulland@vmware.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now on one uses this function and it seems useless,
so remove usb_find_device.
[tom@tom linux-2.6-next]$ grep -r -n -I usb_find_device ./
drivers/media/dvb/dvb-usb/dvb-usb-init.c:160:static struct
dvb_usb_device_description * dvb_usb_find_device(struct usb_device
*udev,struct dvb_usb_device_properties *props, int *cold)
drivers/media/dvb/dvb-usb/dvb-usb-init.c:230: if ((desc =
dvb_usb_find_device(udev,props,&cold)) == NULL) {
drivers/usb/core/usb.c:630: * usb_find_device - find a specific usb device in the system
drivers/usb/core/usb.c:642:struct usb_device *usb_find_device(u16 vendor_id, u16 product_id)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In to places in fsg_common_init() an unconditional call to kfree()
on common was performed in error recovery which is not a valid
behaviour since fsg_common structure is not always allocated by
fsg_common_init().
To fix, the calls has been replaced with a goto to a proper error
recovery which does the correct thing.
Also, refactored fsg_common_release() function.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Obviously, {} is needed in the branch of
"else if (hcd->driver->flags & HCD_LOCAL_MEM)"
for handling of setup packet mapping.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An undocumented "feature" in the OMAP3 EHCI controller causes
suspended ports to be taken out of suspend when the USBCMD.Run/Stop
bit is cleared (this bit is normally cleared when ehci_bus_suspend
is called).
This "feature" breaks suspend-resume if the root-hub is allowed
to suspend. (The controller thinks it is in resume, and the PHY
thinks it is still in suspend).
There is an undocumented register bit that can be used to disable
this feature and restore normal behavior. Set this bit so
suspend-resume can work normally.
Tested on OMAP3 SDPs with the NXP ISP1504 and NXP ISP1703 PHYs.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1379) reworks the logic for handling USB interface
runtime-PM settings -- hopefully it's right this time! The problem is
that when a driver is unbound or binding fails, runtime PM for the
interface always gets disabled. But pm_runtime_disable() nests, so it
shouldn't be called unless the interface was previously enabled for
runtime PM.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rob Duncan <Robert.Duncan@exar.com>
Tested-by: Rob Duncan <Robert.Duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change transfer ring behavior to not follow/activate link TRBs
until active TRBs are queued after it. This change affects
the behavior when a TD ends just before a link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix g_ffs build error, add a needed header file:
drivers/usb/gadget/f_fs.c:1064:error: 'PAGE_CACHE_SIZE' undeclared (first use in this function)
drivers/usb/gadget/f_fs.c:1065:error: 'PAGE_CACHE_SHIFT' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OMAP systems, we have two different OHCI controllers. The legacy
one is present in OMAP1/2 chips, and the newer one comes bundled as
a companion to the EHCI controller on OMAP3 and newer chips.
We may have multi-omap configurations where OMAP2 and OMAP3
support may be enabled in the same kernel, and need a mechanism
to keep both drivers around.
This patch adds a Kconfig entry for each of these drivers.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the OHCI controller present in OMAP3 and newer chips.
The code is mostly based off the ehci-omap.c driver.
Some of it is common to both drivers and will eventually
need to be factored out to platform init files.
In its current state, the driver cannot co-exist with the ehci-omap
driver, and this will be fixed in later versions. The second driver
to be loaded will overwrite settings made by the other. For now,
this driver should allow the few users of OMAP3 OHCI to get going.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renamed fsl_mx3_udc.c -> fsl_mxc_udc.c
for mx51, usb core is clocked from sources that are not 60mhz.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverse priority of errors reported to ldisc so that it matches that of
other serial drivers (break takes precedence over parity, which takes
precedence over framing errors).
Also make sure overrun errors are handled as in other drivers, that is,
an overrun error is always reported and is not associated with any
received character (instead a NULL character with the TTY_OVERRUN flag
set is inserted).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use tty_insert_flip_string_fixed_flag to report errors to line
discipline.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use tty_insert_flip_string_fixed_flag to report errors to line
discipline.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were some reports[1] of isp1760 USB driver malfunctioning
with high speed devices, noticed on Blackfin and PowerPC targets.
These reports indicated that the original Philips 'pehcd'[2]
driver worked fine.
We've noticed the same issue with an ARM RealView platform. This
happens under load (with only some mass storage devices, not all,
just as in another report[3]):
error bit is set in DW3
error bit is set in DW3
error bit is set in DW3
usb 1-1.2: device descriptor read/64, error -32
It appears that the 'pehcd' driver checks the X bit only if the
transaction is halted (H bit), otherwise the error is so far
insignificant.
The ISP176x chips were modeled after EHCI, and EHCI spec says
(thanks to Alan Stern for pointing out):
"Transaction errors cause the status field to be updated to reflect
the type of error, but the transaction continues to be retried until
the Active bit is set to 0. When the error counter reaches 0, the
Halt bit is set and the Active bit is cleared."
So, just as the original Philips driver, isp1760 must report the
error only if the transaction error and the halt bits are set.
[1] http://markmail.org/message/lx4qrlbrs2uhcnly
[2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494
See pehci.c:pehci_hcd_update_error_status().
[3] http://blackfin.uclinux.org/gf/tracker/5148
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When USB3 protocol port detects an USB3.0 device attach, the port will
automatically transition to the Enabled state upon the completion
of successful link training.
Do not disable USB3 protocol ports in hub_activate(), or USB3.0 device
will fail to be recognized if xHCI bus power management is implemented.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression introduced by commit
a108bfcb37 (USB: tty: Prune uses of
tty_request_room in the USB layer) which broke three drivers
(cypress_m8, digi_acceleport and spcp8x5) through incorrect use of
tty_insert_flip_string_fixed_flag.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch that makes sure that the device ID data (idVendor,
idProduct and bcdDevice) are assigned to the descriptor in the cdev
structure *before* the composite gadget starts binding. This allows the
composite driver, and all the composite functions it uses, access to
that data.
In one of the composite functions we created, we needed to register an
input device and wanted to use the idVendor, idProduct and bcdDevice
codes to properly initialize the id field of the input device. We could
not do that because the idVendor, idProduct and bcdDevice values were
only set in the cdec structure *after* the composite->bind(cdev) call.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After using state stored in xhci_virt_ep to clean up a stalled endpoint,
be sure to set the stalled stream ID back to 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Function Filesystem (FunctioFS) lets one create USB
composite functions in user space in the same way as GadgetFS
lets one create USB gadgets in user space. This allows
creation of composite gadgets such that some of the functions
are implemented in kernel space (for instance Ethernet, serial
or mass storage) and other are implemented in user space.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The FunctionFS is a USB composite function that can be used
with the composite framework to create an USB gadget.
>From kernel point of view it is just a composite function with
some unique behaviour. It may be added to an USB
configuration only after the user space driver has registered
by writing descriptors and strings (the user space program has
to provide the same information that kernel level composite
functions provide when they are added to the configuration).
>From user space point of view it is a file system which when
mounted provide an "ep0" file. User space driver need to
write descriptors and strings to that file. It does not need
to worry about endpoints, interfaces or strings numbers but
simply provide descriptors such as if the function was the
only one (endpoints and strings numbers starting from one and
interface numbers starting from core). The FunctionFS changes
numbers of those as needed also handling situation when
numbers differ in different configurations.
When descriptors and strings are written "ep#" files appear
(one for each declared endpoint) which handle communication on
a single endpoint. Again, FunctionFS takes care of the real
numbers and changing of the configuration (which means that
"ep1" file may be really mapped to (say) endpoint 3 (and when
configuration changes to (say) endpoint 2)). "ep0" is used
for receiving events and handling setup requests.
When all files are closed the function disables itself.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__init, __initdata and __exit tags have have been removed from
various files to make it possible for gadgets that do not use
the __init/__exit tags to use those.
Files in question are related to:
* the core composite framework,
* the mass storage function (fixing a section mismatch) and
* ethernet driver (ACM, ECM, RNDIS).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove multi-urb write from the generic driver and simplify the
prepare_write_buffer prototype:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void *dest, size_t size);
The default implementation simply fills dest with data from port write
fifo but drivers can override it if they need to process the outgoing
data (e.g. add headers).
Turn ftdi_sio into a generic fifo-based driver, which lowers CPU usage
significantly for small writes while retaining maximum throughput.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reimplement fifo-based writes in the generic driver using a multiple
pre-allocated urb scheme.
In contrast to multi-urb writes, no allocations (of urbs or buffers) are
made during run-time and there is less pressure on the host stack
queues as currently only two urbs are used (implementation is generic
and can handle more than two urbs as well, though).
Initial tests using ftdi_sio show that the implementation achieves the
same (maximum) throughput at high baudrates as multi-urb writes. The CPU
usage is much lower than for multi-urb writes for small write requests
and only slightly higher for large (e.g. 2k) requests (due to extra copy
via fifo?).
Also outperforms multi-urb writes for small write requests on an
embedded arm-9 system, where multi-urb writes are CPU-bound at high
baudrates (perf reveals that a lot of time is spent in the host stack
enqueue function -- could perhaps be a bug as well).
Keeping the original write_urb, buffer and flag for now as there are
other drivers depending on them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill circular buffers for tx and rx as well as read work thread, and
switch to generic kfifo-based write implementation.
This is an example of how prepare_write_buffer and process_read_urb can
be used to handle protocols with packet headers.
Please note the diffstat which shows that the same functionality is now
provided using only a tenth of the code (including whitespace and
comments, though).
Tested-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original SIO devices require a control byte for every packet
written. Clean up the unnecessarily messy implementation of this.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch to the generic, multi-urb, write implementation.
Note that this will also make it fairly easy to use the generic
fifo-based write implementation: simply unset the multi_urb_write flag
and modify prepare_write_buffer (or unset if not using a legacy SIO
device). This may be desirable for instance on an embedded system where
optimal throughput at high baudrates may not be as important as other
factors (e.g. no allocations during runtime and less pressure on host
stack).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one
errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1377) simplifies the code in usb_sg_init(), without
changing its functionality. It also removes a couple of unused fields
from the usb_sg_request structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This webcam gadget instantiates a UVC camera (360p and 720p resolutions
in YUYV and MJPEG).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This USB video class function driver implements a video capture device from the
host's point of view. It creates a V4L2 output device on the gadget's side to
transfer data from a userspace application over USB.
The UVC-specific descriptors are passed by the gadget driver to the UVC
function driver, making them completely configurable without any modification
to the function's driver code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the type of the URB's 'sg' pointer from a usb_sg_request to
a scatterlist. This allows drivers to submit scatter-gather lists
without using the usb_sg_wait() interface. It has the added benefit
of removing the typecasts that were added as part of patch as1368 (and
slightly decreasing the number of pointer dereferences).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converting a pipe number to a struct usb_host_endpoint pointer is a little
messy. Introduce a new convenience function to hide the mess.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qset_print() was not declared static although it is not used
outside of debug.c
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These Appotech controllers are found in Picture Frames, they provide a
(buggy) emulation of a cdrom drive which contains the windows software
Uploading of pictures happens over the corresponding /dev/sg device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The max packet length bit mask used for isochronous endpoints
should be 0x7FF instead of 0x8FF. 0x8FF will actually clear
higher-order bits in the max packet length field.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM3517 is based on ES3.1 thus ES2.x related programming is invalid
for it so updating ES2.x programming.
Also fixed below checkpatch warning:
WARNING: unnecessary whitespace before a quoted newline
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes below compilation warning:
drivers/usb/host/ehci-hcd.c:425:
warning: 'ehci_port_power' defined but not used
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another CDC-ACM + vendor specific interface layout.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device is disconnected, xhci_free_virt_device() is called. Ramya
found that if the device had streams enabled, and then the driver freed
the streams with a call to usb_free_streams(), then about a minute after
he had called this, his machine crashed with a Bad DMA error. It turns
out that xhci_free_virt_device() would attempt to free the endpoint's
stream_info data structure if it wasn't NULL, and the free streams
function was not setting it to NULL after freeing it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Ramya Desai <ramya.desai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that URB_NO_SETUP_DMA_MAP is no longer in use, this patch (as1376)
removes all references to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1375) eliminates the usb_host_ss_ep_comp structure used
for storing a dynamically-allocated copy of the SuperSpeed endpoint
companion descriptor. The SuperSpeed descriptor is placed directly in
the usb_host_endpoint structure, alongside the standard endpoint
descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1373) fixes a couple of drivers outside the USB
subtree. Devices are now disabled or enabled for autosuspend by
calling a core function instead of setting a flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL isn't anymore present into this file thus it is no necessary still include smp_lock.h.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL is not needed here because necessary locking is already provided
by mutex sisusb->lock.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds handling of the "Start/Stop Unit" SCSI request
to simulate media ejection.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a sysfs entry (/sys/devices/platform/_UDC_/gadget/suspended) to
show the suspend state of an USB composite gadget.
Signed-off-by: Fabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix usb sparse warnings:
drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci'
drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci'
drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer
drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static?
drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static?
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_gat_configuratio() used two pointers to point to the same
memory. Code simplified, by removing one of them.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix mos7720 Kconfig dependencies.
When an enabled bool selects a tristate, the tristate becomes =y,
even if it should be limited to modular, so limit the bool kconfig
option to configs that will build cleanly.
Also change the if-block to a simple depends on.
drivers/built-in.o: In function `mos7720_release':
mos7720.c:(.text+0xad432): undefined reference to `parport_remove_port'
drivers/built-in.o: In function `mos7715_parport_init':
mos7720.c:(.text+0xae197): undefined reference to `parport_register_port'
mos7720.c:(.text+0xae210): undefined reference to `parport_announce_port'
drivers/built-in.o:(.data+0x201c8): undefined reference to `parport_ieee1284_read_nibble'
drivers/built-in.o:(.data+0x201d0): undefined reference to `parport_ieee1284_read_byte'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No functionality added or bugs fixed, just improved code consistency and
(hopefully) readability by replacing send_mos_cmd with the register read & write
functions that were used for parallel port registers. Also shortens overall
file length.
Thoroughly tested, with emphasis on regression testing the serial port.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the parallel port on the moschip MCS7715 device. The port
registers itself with the parport subsystem as a low-level driver. A separate
entry to the kernel configuration is added beneath that for the mos7720, to
avoid the need to link with the parport subsystem code for users who don't have
or don't want the parallel port. Only compatibility mode is currently supported
(no ECP/EPP). Tested with both moschip devices (7720 and 7715) on UP and SMP
hosts, including regression testing of serial port, concurrent operation of
serial and parallel ports, and various connect / disconnect scenarios.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This renames the functions usb_buffer_alloc and usb_buffer_free to the correct
ones for the drivers in the staging tree.
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed coding styles in the ueagle usb driver.
Signed-off-by: Javier Blanco de Torres <jblanco@neurowork.net>
Signed-off-by: Alejandro Sánchez Acosta <asanchez@neurowork.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
isp1301 transceiver driver init should be done before we do ohci omap init
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been running with this patch on my Niagara2 boxes for some time
and have not seen any ill effects yet. Maybe we can stash this into
the USB tree to get exposure for some time in -next and if anything
crops up we can simply revert?
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems unlikely that this entry is needed anymore since the kernel
has logic to handle devices that poorly respond to INQUIRY. Since we
now have another entry with the same VID/PID but different flags, it's
a good time to attempt to clean this up.
The original submitter's email no longer works, so we'll keep an eye
out for any regression reports.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bulk endpoint streams were added in the USB 3.0 specification. Streams
allow a device driver to overload a bulk endpoint so that multiple
transfers can be queued at once.
The device then decides which transfer it wants to work on first, and can
queue part of a transfer before it switches to a new stream. All this
switching is invisible to the device driver, which just gets a completion
for the URB. Drivers that use streams must be able to handle URBs
completing in a different order than they were submitted to the endpoint.
This requires adding new API to set up xHCI data structures to support
multiple queues ("stream rings") per endpoint. Drivers will allocate a
number of stream IDs before enqueueing URBs to the bulk endpoints of the
device, and free the stream IDs in their disconnect function. See
Documentation/usb/bulk-streams.txt for details.
The new mass storage device class, USB Attached SCSI Protocol (UASP), uses
these streams API.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Much of the xHCI driver code assumes that endpoints only have one ring.
Now an endpoint can have one ring per enabled stream ID, so correct that
assumption. Use functions that translate the stream_id field in the URB
or the DMA address of a TRB into the correct stream ring.
Correct the polling loop to print out all enabled stream rings. Make the
URB cancellation routine find the correct stream ring if the URB has
stream_id set. Make sure the URB enqueueing routine does the same. Also
correct the code that handles stalled/halted endpoints.
Check that commands and registers that can take stream IDs handle them
properly. That includes ringing an endpoint doorbell, resetting a
stalled/halted endpoint, and setting a transfer ring dequeue pointer
(since that command can set the dequeue pointer in a stream context or an
endpoint context).
Correct the transfer event handler to translate a TRB DMA address into the
stream ring it was enqueued to. Make the code to allocate and prepare TD
structures adds the TD to the right td_list for the stream ring. Make
sure the code to give the first TRB in a TD to the hardware manipulates
the correct stream ring.
When an endpoint stalls, store the stream ID of the stream ring that
stalled in the xhci_virt_ep structure. Use that instead of the stream ID
in the URB, since an URB may be re-used after it is given back after a
non-control endpoint stall.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for allocating streams for USB 3.0 bulk endpoints. See
Documentation/usb/bulk-streams.txt for more information about how and why
you would use streams.
When an endpoint has streams enabled, instead of having one ring where all
transfers are enqueued to the hardware, it has several rings. The ring
dequeue pointer in the endpoint context is changed to point to a "Stream
Context Array". This is basically an array of pointers to transfer rings,
one for each stream ID that the driver wants to use.
The Stream Context Array size must be a power of two, and host controllers
can place a limit on the size of the array (4 to 2^16 entries). These
two facts make calculating the size of the Stream Context Array and the
number of entries actually used by the driver a bit tricky.
Besides the Stream Context Array and rings for all the stream IDs, we need
one more data structure. The xHCI hardware will not tell us which stream
ID a transfer event was for, but it will give us the slot ID, endpoint
index, and physical address for the TRB that caused the event. For every
endpoint on a device, add a radix tree to map physical TRB addresses to
virtual segments within a stream ring.
Keep track of whether an endpoint is transitioning to using streams, and
don't enqueue any URBs while that's taking place. Refuse to transition an
endpoint to streams if there are already URBs enqueued for that endpoint.
We need to make sure that freeing streams does not fail, since a driver's
disconnect() function may attempt to do this, and it cannot fail.
Pre-allocate the command structure used to issue the Configure Endpoint
command, and reserve space on the command ring for each stream endpoint.
This may be a bit overkill, but it is permissible for the driver to
allocate all streams in one call and free them in multiple calls. (It is
not advised, however, since it is a waste of resources and time.)
Even with the memory and ring room pre-allocated, freeing streams can
still fail because the xHC rejects the configure endpoint command. It is
valid (by the xHCI 0.96 spec) to return a "Bandwidth Error" or a "Resource
Error" for a configure endpoint command. We should never see a Bandwidth
Error, since bulk endpoints do not effect the reserved bandwidth. The
host controller can still return a Resource Error, but it's improbable
since the xHC would be going from a more resource-intensive configuration
(streams) to a less resource-intensive configuration (no streams).
If the xHC returns a Resource Error, the endpoint will be stuck with
streams and will be unusable for drivers. It's an unavoidable consequence
of broken host controller hardware.
Includes bug fixes from the original patch, contributed by
John Youn <John.Youn@synopsys.com> and Andy Green <AGreen@PLXTech.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ids for Qualcomm Gobi 2000 QDL and Modem modes. Gobi 2000 has a
single altsetting in QDL mode, so adapt code to handle that.
Firmware upload protocol is also slightly different, with an
additional firmware file. However, qcserial doesn't handle firmware
uploading.
Tested on Lenovo Thinkpad T510.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
