Just like all previous UAS capable Seagate disk enclosures, these need the
US_FL_NO_ATA_1X to not crash when udev probes them.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems
with newer ASM1153 disk enclosures in 2 ways:
1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which
we assume is always an ASM1051, so remove the quirk for 5106, and instead
use the same detection logic as we already use for device-id 55aa, which is
used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>.
2) Our detection logic to differentiate between ASM1051 and ASM1053 sees
ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs.
Luckily the ASM1153 descriptors are not 100% identical, unlike the previous
models the ASM1153 has bMaxPower == 0, so use that to differentiate it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Apricorn SATA dongle will occasionally return "USBSUSBSUSB" in
response to SCSI commands when running in UAS mode. Therefore,
disable UAS mode on this dongle.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the JMicron JMS567 enclosures with the JMS566 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Takeo Nakayama <javhera@gmx.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is yet another Seagate device which needs the US_FL_NO_ATA_1X quirk
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does two things for SCM eUSCSI USB-SCSI converters:
1. SCM eUSCSI bridge devices are hard-wired to use SCSI ID 7. On connecting
the converter, access to that ID is attempted during the bus scan. Asking
the converter to issue INQUIRY commands to itself isn't very polite and
wastes time. Set this_id to 7 so __scsi_scan_target() skips it in the scan.
2. Enable multi-LUN support. eUSCSI devices don't support Get Max LUN
requests, returning an error (-32). [Different targets could have different
numbers of LUNs, so it wouldn't make sense to return a particular value in
response to Get Max LUN.]
usb_stor_scan_dwork() does this:
/* For bulk-only devices, determine the max LUN value */
if (us->protocol == USB_PR_BULK && !(us->fflags & US_FL_SINGLE_LUN)) {
mutex_lock(&us->dev_mutex);
us->max_lun = usb_stor_Bulk_max_lun(us);
mutex_unlock(&us->dev_mutex);
It avoids calling usb_stor_Bulk_max_lun() if US_FL_SINGLE_LUN, but not for
US_FL_SCM_MULT_TARG. Since usb_stor_Bulk_max_lun() returns 0 in the error
case, us->max_lun was always set to 0.
[If the user doesn't want multi-LUN support (perhaps there are SCSI devices
which respond to commands on all LUNs?), the US_FL_SINGLE_LUN quirk can be
specified on the kernel command line.]
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_stor_euscsi_init() enables multi-target mode for SCM eUSB SCSI bridge
devices. The control message it sends has wLength = 1 and the byte sent is
0x01. While that works, the SCM Windows driver does it with wLength = 0. We
may as well match what the SCM driver does.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly, so we need to fall-back to usb-storage for these.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should be using the standard dev_printk() variants for
sense code printing.
[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some mass storage devices return a bogus value in response to a Get Max LUN
request. The Iomega Jaz USB Adapter responds with 0x10, hence my recent
patch to use the US_FL_SINGLE_LUN quirk for it.
The USB MSC Bulk Only Transport document says "The device shall return one
byte of data that contains the maximum LUN supported by the device."
Since the LUN field in the command block wrapper is only 4 bits wide, it
might be helpful to report too-large LUN values in the kernel log, and
assume max LUN is actually 0. That could get some devices which currently
need the US_FL_SINGLE_LUN quirk to work.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bda9893c50 as it was
incorrect.
Reported-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No caller or macro uses the return value so make it void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With uas over usb-3 the tags inside the uas iu-s must match the usb-3 stream
ids, and those go from 1 - qdepth.
Before blk-mq calling scsi_activate_tcq(sdev, qdepth) guaranteed that we would
only get cmnd->request->tag from 0 - (qdepth - 1), and we used those as
uas-tags / stream-ids.
With blk-mq however we are guaranteed to never get more then qdepth commands
queued at the same time, but the cmnd->request->tag values may be much larger,
which breaks uas.
This commit fixes this by generating uas tags in the 1 - qdepth range ourselves
instead of using cmnd->request->tag.
While touching all involved code anyways also rename the uas_cmd_info stream
field to uas_tag, because when using uas over usb-2 streams are not used.
Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
--
Changes in v2:
-Remove ".disable_blk_mq = true" from uas_host_template
Changes in v3:
-Rebased on top of Linus' current master branch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB patchset for 3.18-rc1. Also in here is the PHY tree,
as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full details
in the changelog below.
All have been in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aLYACgkQMUfUDdst+ylBvwCgs9fGRj0RQkLyGhQdEpzdZtTU
ZcwAoMPBImnaA1ZeSl7ZnoO8vC/WE4bR
=tfpj
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
This patch set consists of the usual driver updates (megaraid_sas, arcmsr,
be2iscsi, lpfc, mpt2sas, mpt3sas, qla2xxx, ufs) plus several assorted fixes
and miscellaneous updates (including the pci_msix_enable_range() changes that
have been pending for a while).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUNHvtAAoJEDeqqVYsXL0MzaoIAJ/R2JW/Xm50rD6iUj6RfjEc
6OOi3sOJe6yivPFLLTmIZyLcgHuZKPVXsjcjBXENsrjJeyu2aTq+vs2bOJN9BRYU
gHGyAEhVPKsvecYhEj/78ClRIMzwkr7KQMQConbClDa0sVr62M/dPQVHNvjaTDeS
rtmPGZbNpv9rCl0itNBLMrnOBT/MduuWtS2VNCAkV5yFU8kvEax5pizB+W4ztjoe
BnVnF8OJC70wAM4vpiUcgwCR5AGmYv5SQKn3AHNBayrJic0MLUSIhrnCptc9TSir
zWJAyoW2iQY1LKmihjwjDlXP40jbfOaBacEycqTUKNkfMRKbBl3qQa4IUrR1XsQ=
=I1Yg
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (megaraid_sas,
arcmsr, be2iscsi, lpfc, mpt2sas, mpt3sas, qla2xxx, ufs) plus several
assorted fixes and miscellaneous updates (including the
pci_msix_enable_range() changes that have been pending for a while)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (202 commits)
scsi: add a CONFIG_SCSI_MQ_DEFAULT option
ufs: definitions for phy interface
ufs: tune bkops while power managment events
ufs: Add support for clock scaling using devfreq framework
ufs: Add freq-table-hz property for UFS device
ufs: Add support for clock gating
ufs: refactor configuring power mode
ufs: add UFS power management support
ufs: introduce well known logical unit in ufs
ufs: manually add well known logical units
ufs: Active Power Mode - configuring bActiveICCLevel
ufs: improve init sequence
ufs: refactor query descriptor API support
ufs: add voting support for host controller power
ufs: Add clock initialization support
ufs: Add regulator enable support
ufs: Allow vendor specific initialization
scsi: don't add scsi_device if its already visible
scsi: fix the type for well known LUs
scsi: fix comment in struct Scsi_Host definition
...
This is a set of two small fixes, both to code which went in during the merge
window: cxgb4i has a scheduling in atomic bug in its new ipv6 code and uas
fails to work properly with the new scsi-mq code.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUMMu/AAoJEDeqqVYsXL0MRlQH/1qE/e5xRfpftgTtjpqC0BFa
7M4X48YRCxuKi/QJ3oOMpdj30ExXZ8sKfHsQiXBDlgyJzjE2sfsz70Z/mnm7kfxv
y0c9+C4y4AJ9b3Qn67Zk7l/elpZdzYfk2WFZsJ+AvC/bBXUTff7G1I2wnC36gdS4
S3+ZlCmbNlR1CNNm6xrqEKgGRIuQxonI5foJj6ovz/OvHiFQfpYTm0IvZNNCXYD3
rLg1661WA9BJP/r+B5uTwCmlNxJereiLJJwPR39OxWYXwgsvHVNYP/ae7NNFPl3R
zT1oeoaLoZn0r6lZKFmH3W4Sa2C7tZ0aWROCtU6O/EhUUQCXJPJfOYgwNPGVUaE=
=RzIY
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of two small fixes, both to code which went in during
the merge window: cxgb4i has a scheduling in atomic bug in its new
ipv6 code and uas fails to work properly with the new scsi-mq code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] uas: disable use of blk-mq I/O path
[SCSI] cxgb4i: avoid holding mutex in interrupt context
The stream_id and pipe are already present in uas_cmd_info resp uas_dev_info,
so there is no need to pass a copy along.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uas driver uses the block layer tag for USB3 stream IDs. With
blk-mq we can get larger tag numbers that the queue depth, which breaks
this assumption. A fix is under way for 3.18, but sits on top of
large changes so can't easily be backported. Set the disable_blk_mq
path so that a uas device can't easily crash the system when using
blk-mq for SCSI.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is apparently another SCM USB-SCSI converter with ID 04E6:000F. It
is listed along with 04E6:000B in the Windows INF file for the Startech
ICUSBSCSI2 as "eUSB SCSI Adapter (Bus Powered)". The quirk allows
devices with SCSI ID other than 0 to be accessed.
Also make a couple of existing SCM product IDs lower case to be
consistent with other entries.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Castlewood Systems supplied various models of USB-SCSI converter with their
ORB external removable-media drive. The ORB Windows and Macintosh drivers
support six USB IDs:
084B:A001 [VID 084B is Castlewood Systems]
04E6:0002 (*) ORB USB Smart Cable P/N 88205-001 (generic SCM ID)
2027:A001 Double-H Technology DH-2000SC
1822:0001 (*) Ariston iConnect/iSCSI
07AF:0004 (*) Microtech XpressSCSI (25-pin)
07AF:0005 (*) Microtech XpressSCSI (50-pin)
*: quirk already in unusual-devs.h
[Apparently the official VID for Double-H Technology is 0x07EB = 2027
decimal. That's another hex/decimal mix-up with these SCM-based products
(in addition to the Ariston and Entrega ones). Perhaps the USB-IF informed
companies of their allocated VID in decimal, but they assumed it was hex?
It seems all Entrega products used VID 0x1645, not just the USB-SCSI
converter.]
Double-H Technology Co., Ltd. produced a USB-SCSI converter, model
DH-2000SC, which is probably the one supported by the ORB drivers. Perhaps
the Castlewood-bundled product had a different label or PID though?
Castlewood mentioned Conmate as being one type of USB-SCSI converter.
Conmate and Double-H seem related somehow; both company addresses in the
same road, and at one point the Conmate web site mentioned DH-2000H4,
DH-200D4/DH-2000C4 as models of USB hub (DH short for Double-H presumably).
Conmate did show a USB-SCSI converter model CM-660 on their web site at one
point. My guess is that was identical to the DH-2000SC.
Mention of the Double-H product:
http://web.archive.org/web/20010221010141/http://www.doubleh.com.tw/dh-2000sc.htm
The only picture I could find is at
http://jp.acesuppliers.com/catalog/j64/component/page03.html
The casing design looks the same as my ORB USB Smart Cable which has ID
04E6:0002.
Anyway, that's enough rambling. Here's the patch.
storage: Add quirks for Castlewood and Double-H USB-SCSI converters
Add quirks for two SCM-based USB-SCSI converters which were bundled with
some Castlewood ORB removable drives. Without the quirk only the (single)
drive with SCSI ID 0 can be accessed.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_stor_euscsi_init() calls usb_stor_control_msg() with timeout
argument 5000. USB_CTRL_SET_TIMEOUT is defined to be 5000 in usb.h, so
would it make sense to use that instead? Patch below if it would.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of various drivers/usb files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of dereference each byte let's use %*ph specifier in the printk()
calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If something goes wrong in our communication with an uas device we may get
a response iu in reaction to a cmnd, rather then a status iu. In this case
propagate an error upwards, rather then logging a bogus iu message.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of doing:
uas_log_cmd_state(cmnd, __func__)
scmd_printk(KERN_ERR, cmnd, "error doing foo %d\n", err)
On error, resulting in 2 log calls for a single error, make uas_log_cmd_state
take a status code, and change calls like the above to:
uas_log_cmd_state(cmnd, "error doing foo", err)
Also change various sanity checks (which should never trigger) from:
"scmd_printk(KERN_ERR, cmnd, "sanity foo failed\n")" to calling the new
uas_log_cmd_state(), so that when they do trigger we get more info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've removed all hack from the driver for pre-production hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've access to a number of different uas devices now, and none of them use
old style sense urbs. The only case where these code-paths trigger is with
the asm1051 and there they do the wrong thing, as the asm1051 sends 8 bytes
status iu-s when it does not have any sense data, but uses new style
sense iu-s regardless, as can be seen for scsi cmnds where there is sense
data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was only used to sanity check against completing the same cmnd twice,
but that is the case we're likely operating on free-ed memory, and doing
sanity checks on free-ed memory is not really helpful.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_print_command to print commands during errors, rather then printing
the rather meaningless pointer to the command.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for both type of cancellation codes for sense and data urbs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
