Add hwblk_id to Solution Engine 7724 board specific
on-chip sh7724 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to kfr2r09 board specific on-chip sh7724
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to AP325RXA board specific on-chip sh7723
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7722 board specific
on-chip sh7722 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Migo-R board specific on-chip sh7722
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These patches extend struct platform device data for a bunch of
SuperH Mobile processors and embedded boards. The patches simply
add hardware block ids to on-chip platform devices. Platform
devices off chip (such as external ethernet controllers or flash
chips) are left out which gives them a special case hardware block
id of zero.
Upcoming Runtime PM code will make use of the hardware block id
to group devices together. The hardware block id can also be used
to extend the SuperH Mobile clock framework implementation.
This series of patches depend on the following:
"Driver Core: Add platform device arch data V3".
This patch adds a hwblk_id member to struct pdev_archdata. This member
should be used to point out on-chip hardware block id.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the unused MSTPCRn register definitions
from the SuperH Mobile code for sh7722, sh7723 and sh7724.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds early printk support for SH770x (tested on SH7709 based hp6xx).
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'i2c-fixes-rc4' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: OMAP3430 Silicon Errata 1.153
i2c-omap: In case of a NACK|ARDY|AL return from the ISR
i2c-omap: Bug in reading the RXSTAT/TXSTAT values from the I2C_BUFFSTAT register
i2c-sh_mobile: change module_init() to subsys_initcall()
i2c: strncpy does not null terminate string
i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC value
Add the relevant git repositories and affected files to the maintainership
of HP Jornada 700-series and Epson s1d13xxxfb support.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some touchups to the sample record.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow an option to control the minimum percentage of sign-offs required
before being considered a maintainer.
git-min-percent has a default value of 5
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow an option to control the minimum percentage of sign-offs required
before being considered a maintainer.
git-min-percent has a default value of 5
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't require a specific file in a directory to be tested.
Also Arnd Bergmann pointed out that the MAINTAINERS pattern requirement
that directory patterns have a trailing slash was unnecessary and was
likely to be error prone. Removed that requirement.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Woller's email address bounces
Nils Faerber isn't active
Added Thomas Woller to CREDITS, Nils already has an entry
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Layes is hard to find.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
from sections that should not have them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When SERIAL_ATMEL_CONSOLE is disabled, ATMEL_CONSOLE_DEVICE is set to
NULL, and trying to access ATMEL_CONSOLE_DEVICE->flags in
atmel_serial_probe makes the compile fail. This fixes the issue by only
accessing it if CONFIG_SERIAL_ATMEL_CONSOLE is defined
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Once a structure goes over PAGE_SIZE*2, we see occasional allocation
failures. Some people have chosen to switch over to things like vmalloc()
that will let them keep array-like access to such a large structures.
But, vmalloc() has plenty of downsides.
Here's an alternative. I think it's what Andrew was suggesting here:
http://lkml.org/lkml/2009/7/2/518
I call it a flexible array. It does all of its work in PAGE_SIZE bits, so
never does an order>0 allocation. The base level has
PAGE_SIZE-2*sizeof(int) bytes of storage for pointers to the second level.
So, with a 32-bit arch, you get about 4MB (4183112 bytes) of total
storage when the objects pack nicely into a page. It is half that on
64-bit because the pointers are twice the size. There's a table detailing
this in the code.
There are kerneldocs for the functions, but here's an
overview:
flex_array_alloc() - dynamically allocate a base structure
flex_array_free() - free the array and all of the
second-level pages
flex_array_free_parts() - free the second-level pages, but
not the base (for static bases)
flex_array_put() - copy into the array at the given index
flex_array_get() - copy out of the array at the given index
flex_array_prealloc() - preallocate the second-level pages
between the given indexes to
guarantee no allocs will occur at
put() time.
We could also potentially just pass the "element_size" into each of the
API functions instead of storing it internally. That would get us one
more base pointer on 32-bit.
I've been testing this by running it in userspace. The header and patch
that I've been using are here, as well as the little script I'm using to
generate the size table which goes in the kerneldocs.
http://sr71.net/~dave/linux/flexarray/
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 8dfd0374be ("MMC core: limit
minimum initialization frequency to 400kHz") MMC core checks for minimum
frequency, and that causes following messages flood when using eSDHC
controllers:
...
mmc0: Minimum clock frequency too high for identification mode
mmc0: Minimum clock frequency too high for identification mode
...
The warnings are legitimate, since if we'd use 133 MHz clocks for standard
SDHCI controllers, we'd not able to scale frequency down to 400 kHz.
But eSDHC controllers have a non-standard SD clock management, so we can
divide clock by 256 * 16, not just 256.
This patch introduces get_min_clock() callback for sdhci core and
implements it for sdhci-of driver, and thus fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit d6580a9f15 ("kexec: sysrq: simplify
sysrq-c handler") changed the behavior of sysrq-c to unconditional
dereference of NULL pointer. So in cases with CONFIG_KEXEC, where
crash_kexec() was directly called from sysrq-c before, now it can be said
that a step of "real oops" was inserted before starting kdump.
However, in contrast to oops via SysRq-c from keyboard which results in
panic due to in_interrupt(), oops via "echo c > /proc/sysrq-trigger" will
not become panic unless panic_on_oops=1. It means that even if dump is
properly configured to be taken on panic, the sysrq-c from proc interface
might not start crashdump while the sysrq-c from keyboard can start
crashdump. This confuses traditional users of kdump, i.e. people who
expect sysrq-c to do common behavior in both of the keyboard and proc
interface.
This patch brings the keyboard and proc interface behavior of sysrq-c in
line, by forcing panic_on_oops=1 before oops in sysrq-c handler.
And some updates in documentation are included, to clarify that there is
no longer dependency with CONFIG_KEXEC, and that now the system can just
crash by sysrq-c if no dump mechanism is configured.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Brayan Arraes <brayan@yack.com.br>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found with make headers_check
/usr/include/linux/pps.h:52: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This file makes use of various macros defined in files like asm/current.h
or asm-generic/resource.h. All these files can be included via sched.h.
The building of the !MMU ARM kernel (with additional patches) fails
without this change.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DCCP protocol tries to allocate some large hash tables during
initialisation using the largest size possible. This can be larger than
what the page allocator can provide so it prints a warning. However, the
caller is able to handle the situation so this patch suppresses the
warning.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When profile= is used, a large buffer is allocated early at boot. This
can be larger than what the page allocator can provide so it prints a
warning. However, the caller is able to handle the situation so this
patch suppresses the warning.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The page allocator warns once when an order >= MAX_ORDER is specified.
This is to catch callers of the allocator that are always falling back to
their worst-case when it was not expected. However, there are cases where
the caller is behaving correctly but cannot suppress the warning. This
patch allows the warning to be suppressed by the callers by specifying
__GFP_NOWARN.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit ec64f51545 ("cgroup: fix
frequent -EBUSY at rmdir"), cgroup's rmdir (especially against memcg)
doesn't return -EBUSY by temporary ref counts. That commit expects all
refs after pre_destroy() is temporary but...it wasn't. Then, rmdir can
wait permanently. This patch tries to fix that and change followings.
- set CGRP_WAIT_ON_RMDIR flag before pre_destroy().
- clear CGRP_WAIT_ON_RMDIR flag when the subsys finds racy case.
if there are sleeping ones, wakes them up.
- rmdir() sleeps only when CGRP_WAIT_ON_RMDIR flag is set.
Tested-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reported-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reviewed-by: Paul Menage <menage@google.com>
Acked-by: Balbir Sigh <balbir@linux.vnet.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under certain circumstances msleep(1) within the loop, which waits for the
EEPROM to be finished, might take longer than the timeout. On the next
loop the status register might now return to be ready and therefore the
loop finishes. The following check now tests if a timeout occurred and if
so returns an error although the device reported it was ready.
This fix replaces testing the occurrence of the timeout by testing the
"not ready" bit in the status register.
Signed-off-by: Sebastian Heutling <heutling@who-ing.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bug was introduced by commit cc31edceee
("cgroups: convert tasks file to use a seq_file with shared pid array").
We cache a pid array for all threads that are opening the same "tasks"
file, but the pids in the array are always from the namespace of the
last process that opened the file, so all other threads will read pids
from that namespace instead of their own namespaces.
To fix it, we maintain a list of pid arrays, which is keyed by pid_ns.
The list will be of length 1 at most time.
Reported-by: Paul Menage <menage@google.com>
Idea-by: Paul Menage <menage@google.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Reviewed-by: Serge Hallyn <serue@us.ibm.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
