The Spectrum ASIC doesn't support mirroring more than once from a single
binding point (which is a port-direction pair). Therefore detect that a
second binding of a given binding point is attempted.
To that end, extend struct mlxsw_sp_span_inspected_port to track whether
a given binding point is bound or not. Extend
mlxsw_sp_span_entry_port_find() to look for ports based on the full
unique key: port number, direction, and boundness.
Besides fixing the overt bug where configured mirrors are not offloaded,
this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del()
just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to
find the first port with the right number (disregarding the type). Thus
by adding and removing egress and ingress mirrors in the right order,
one could trick the system into believing it has no egress mirrors when
in fact it did have some. That then caused that
mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU
was changed.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ok GACT action, TERMINATE binding_cmd should be used in action set
passed down to HW.
Fixes: b2925957ec ("mlxsw: spectrum_flower: Offload "ok" termination action")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables AVE_GI_RXDROP interrupt factor. This factor indicates
depletion of Rx descriptors and the handler counts the number
of dropped packets.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:
Call trace:
phy_detach+0x94/0x150
phy_disconnect+0x40/0x50
smsc911x_stop+0x104/0x128 [smsc911x]
__dev_close_many+0xb4/0x138
dev_close_many+0xbc/0x190
rollback_registered_many+0x140/0x460
rollback_registered+0x68/0xb0
unregister_netdevice_queue+0x100/0x118
unregister_netdev+0x28/0x38
smsc911x_drv_remove+0x58/0x130 [smsc911x]
platform_drv_remove+0x30/0x50
device_release_driver_internal+0x15c/0x1f8
driver_detach+0x54/0x98
bus_remove_driver+0x64/0xe8
driver_unregister+0x34/0x60
platform_driver_unregister+0x20/0x30
smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
SyS_delete_module+0x1e8/0x238
__sys_trace_return+0x0/0x4
This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()
To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.
Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).
An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.
The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.
In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-03-05
This series contains fixes to e1000e only.
Benjamin Poirier provides all but one fix in this series, starting with
workaround for a VMWare e1000e emulation issue where ICR reads 0x0 on
the emulated device. Partially reverted a previous commit dealing with
the "Other" interrupt throttling to avoid unforeseen fallout from these
changes that are not strictly necessary. Restored the ICS write for
receive and transmit queue interrupts in the case that txq or rxq bits
were set in ICR and the Other interrupt handler read and cleared ICR
before the queue interrupt was raised. Fixed an bug where interrupts
may be missed if ICR is read while INT_ASSERTED is not set, so avoid the
problem by setting all bits related to events that can trigger the Other
interrupt in IMS. Fixed the return value for check_for_link() when
auto-negotiation is off.
Pierre-Yves Kerbrat fixes e1000e to use dma_zalloc_coherent() to make
sure the ring is memset to 0 to prevent the area from containing
garbage.
v2: added an additional e1000e fix to the series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling of National Semi-conductor (no hyphen)
in drivers/net/ethernet/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)
This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.
Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack: 00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0: 00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0: ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!
Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.
The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.
By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).
This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This partially reverts commit 4aea7a5c5e.
We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.
Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".
Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.
Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Until now, we assumed that in case of error when adding FDB entries, the
write operation will fail, but this is not the case. Instead, we need to
check that the number of entries reported in the response is equal to
the number of entries specified in the request.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.
Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.
However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:
$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1
The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.
Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Reported-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multicast snooping is enabled, the Linux bridge resorts to flooding
unregistered multicast packets to all ports only in case it did not
detect a querier in the network.
The above condition is not reflected to underlying drivers, which is
especially problematic in IPv6 environments, as multicast snooping is
enabled by default and since neighbour solicitation packets might be
treated as unregistered multicast packets in case there is no
corresponding MDB entry.
Until the Linux bridge reflects its querier state to underlying drivers,
simply treat unregistered multicast packets as broadcast and allow them
to reach their destination.
Fixes: 9df552ef3e ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables and
also memcpy size_params during devlink resource registration.
Also, introduce a convenient size_param_init helper.
Fixes: ef3116e540 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP_TTL, IP_ECN and IP_DSCP are using the same offset within the
scratchpad as L4 ports. Fix this by shifting all up.
Fixes: 5f57e09091 ("mlxsw: acl: Add ip ttl acl element")
Fixes: i80d0fe4710c ("mlxsw: acl: Add ip tos acl element")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec7711 ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have uninlined the sh_eth_{read|write}() functions introduced in the
commit 4a55530f38 ("net: sh_eth: modify the definitions of register").
Now remove *inline* from sh_eth_tsu_{read|write}() as well and move
these functions from the header to the driver itself. This saves 684
more bytes of object code (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add check for build_skb enabled ring in ixgbe_dma_sync_frag().
In that case &skb_shinfo(skb)->frags[0] may not always be set which
can lead to a crash. Instead we derive the page offset from skb->data.
Fixes: 42073d91a2
("ixgbe: Have the CPU take ownership of the buffers sooner")
CC: stable <stable@vger.kernel.org>
Reported-by: Ambarish Soman <asoman@redhat.com>
Suggested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The login buffer is released before the driver can perform
sanity checks between resources the driver requested and what
firmware will provide. Don't release the login buffer until
the sanity check is performed.
Fixes: 34f0f4e3f4 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIK the only version of smc9194.c with Mac support is the one in the
linux-mac68k CVS repo, which never made it to the mainline.
Despite that, from v2.3.45, arch/m68k/config.in listed CONFIG_SMC9194
under CONFIG_MAC. This mistake got carried over into Kconfig in v2.5.55.
(See pre-git era "[PATCH] add m68k dependencies to net driver config".)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resuming from suspend, the PCI device support must re-enable the
interrupt setting so that interrupts are actually delivered.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJajJahAAoJEEg/ir3gV/o+PTQIALd4/l5VEU1vWqXp6PPaIaRP
fCt4CKXkeIozyOhkiaYLcNAvPnsJRi54a/PGyUbHwxadkjuOhS8WETyQwMf8gbKF
g+LTDseqKjWcu6fUMqe7TmjrNHSo2VErjOjHw1+7emKSkBZuc8zBBND9PqHtOQY6
f1KoUY6IBs22dwqzynxkC5A62VQbTYd0FPnf1n9wN8ubFXSb37KUgKoW4kmMFmLe
JsYEcsAKxpfepnP+EYLyDrVcT1LA9edi5DI5uxSfNgas6bTtjRPhtyZCznDF8rly
jEWv3O2c+HhchuysoACTLiTllviHGj0Myv+rGb0ouhjZWMtulgPPQ04lbYjjr84=
=uF0v
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-02-20
The following pull request includes some fixes for the mlx5 core and
netdevice driver.
Please pull and let me know if there's any issue.
-stable 4.10.y:
('net/mlx5e: Fix loopback self test when GRO is off')
-stable 4.12.y:
('net/mlx5e: Specify numa node when allocating drop rq')
-stable 4.13.y:
('net/mlx5e: Verify inline header size do not exceed SKB linear size')
-stable 4.15.y:
('net/mlx5e: Fix TCP checksum in LRO buffers')
('net/mlx5: Fix error handling when adding flow rules')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If building match list or adding existing fg fails when
node is locked, function returned without unlocking it.
This happened if node version changed or adding existing fg
returned with EAGAIN after jumping to search_again_locked label.
Fixes: bd71b08ec2 ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
First use of drop counters happens in esw_apply_vport_conf function,
while they are allocated later in the flow. Fix that by moving
esw_vport_create_drop_counters function to be called before the first use.
Fixes: b8a0dbe3a9 ("net/mlx5e: E-switch, Add steering drop counters")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We can't allow only some of the rules sharing an FTE to ask for
header re-write, add it to the conflicting action checks.
Fixes: 0d235c3fab ('net/mlx5: Add hash table to search FTEs in a flow-group')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The adapter uses the cache_line_128byte setting to set the bounds for
end padding. On systems where the cacheline size is greater than 128B
use 128B instead of the default of 64B. This results in fewer partial
cacheline writes. There's a 50% chance it will pad to the end of a 256B
cache line vs only 25% when using 64B.
Fixes: f32f5bd2eb ("net/mlx5: Configure cache line size for start and end padding")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When allocating a drop rq, no numa node is explicitly set which means
allocations are done on node zero. This is not necessarily the nearest
numa node to the HCA, and even worse, might even be a memoryless numa
node.
Choose the numa_node given to us by the pci device in order to properly
allocate the coherent dma memory instead of assuming zero is valid.
Fixes: 556dd1b9c3 ("net/mlx5e: Set drop RQ's necessary parameters only")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This isn't supported when we emulate eswitch vlan push action which
is the current state of things.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix these gcc warnings on drivers/net/ethernet/mellanox/mlx5:
[..]/core/lib/clock.c:454:6: warning: no previous prototype for 'mlx5_init_clock' [-Wmissing-prototypes]
[..]/core/lib/clock.c:510:6: warning: no previous prototype for 'mlx5_cleanup_clock' [-Wmissing-prototypes]
[..]/core/en_main.c:3141:5: warning: no previous prototype for 'mlx5e_setup_tc' [-Wmissing-prototypes]
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver tries to copy at least MLX5E_MIN_INLINE bytes into the control
segment of the WQE. It assumes that the linear part contains at least
MLX5E_MIN_INLINE bytes, which can be wrong.
Cited commit verified that driver will not copy more bytes into the
inline header part that the actual size of the packet. Re-factor this
check to make sure we do not exceed the linear part as well.
This fix is aligned with the current driver's assumption that the entire
L2 will be present in the linear part of the SKB.
Fixes: 6aace17e64 ("net/mlx5e: Fix inline header size for small packets")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When GRO is off, the transport header pointer in sk_buff is
initialized to network's header.
To find the udp header, instead of using udp_hdr() which assumes
skb_network_header was set, manually calculate the udp header offset.
Fixes: 0952da791c ("net/mlx5e: Add support for loopback selftest")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When receiving an LRO packet, the checksum field is set by the hardware
to the checksum of the first coalesced packet. Obviously, this checksum
is not valid for the merged LRO packet and should be fixed. We can use
the CQE checksum which covers the checksum of the entire merged packet
TCP payload to help us calculate the checksum incrementally.
Tested by sending IPv4/6 traffic with LRO enabled, RX checksum disabled
and watching nstat checksum error counters (in addition to the obvious
bandwidth drop caused by checksum errors).
This bug is usually "hidden" since LRO packets would go through the
CHECKSUM_UNNECESSARY flow which does not validate the packet checksum.
It's important to note that previous to this patch, LRO packets provided
with CHECKSUM_UNNECESSARY are indeed packets with a correct validated
checksum (even though the checksum inside the TCP header is incorrect),
since the hardware LRO aggregation is terminated upon receiving a packet
with bad checksum.
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After introduction of commit d0869c0071, there were some instances of
RX queue entries from a previous session (before the device was closed
and reopened) returned to the NAPI polling routine. Since the corresponding
socket buffers were freed, this resulted in a panic on reopen. Include
a check for a NULL skb here to avoid this.
Fixes: d0869c0071 ("ibmvnic: Clean RX pool buffers during device close")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89f ("mlxsw: spectrum_router: Provide offload indication using nexthop flags")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c457 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
BUG: sleeping function called from invalid context
in_atomic(): 0, irqs_disabled(): 0, pid: 5762, name: ip
Preemption disabled at:
[<ffffff9d49043564>] debug_object_active_state+0xa4/0x16c
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
PC is at ___might_sleep+0x13c/0x180
LR is at ___might_sleep+0x17c/0x180
[<ffffff9d48ce0924>] ___might_sleep+0x13c/0x180
[<ffffff9d48ce09c0>] __might_sleep+0x58/0x8c
[<ffffff9d49d6253c>] mutex_lock+0x2c/0x48
[<ffffff9d48ed4840>] kernfs_remove_by_name_ns+0x48/0xa8
[<ffffff9d48ed6ec8>] sysfs_remove_link+0x30/0x58
[<ffffff9d49b05840>] __netdev_adjacent_dev_remove+0x14c/0x1e0
[<ffffff9d49b05914>] __netdev_adjacent_dev_unlink_lists+0x40/0x68
[<ffffff9d49b08820>] netdev_upper_dev_unlink+0xb4/0x1fc
[<ffffff9d494a29f0>] rmnet_dev_walk_unreg+0x6c/0xc8
[<ffffff9d49b00b40>] netdev_walk_all_lower_dev_rcu+0x58/0xb4
[<ffffff9d494a30fc>] rmnet_config_notify_cb+0xf4/0x134
[<ffffff9d48cd21b4>] raw_notifier_call_chain+0x58/0x78
[<ffffff9d49b028a4>] call_netdevice_notifiers_info+0x48/0x78
[<ffffff9d49b0b568>] rollback_registered_many+0x230/0x3c8
[<ffffff9d49b0b738>] unregister_netdevice_many+0x38/0x94
[<ffffff9d49b1e110>] rtnl_delete_link+0x58/0x88
[<ffffff9d49b201dc>] rtnl_dellink+0xbc/0x1cc
[<ffffff9d49b2355c>] rtnetlink_rcv_msg+0xb0/0x244
[<ffffff9d49b5230c>] netlink_rcv_skb+0xb4/0xdc
[<ffffff9d49b204f4>] rtnetlink_rcv+0x34/0x44
[<ffffff9d49b51af0>] netlink_unicast+0x1ec/0x294
[<ffffff9d49b51fdc>] netlink_sendmsg+0x320/0x390
[<ffffff9d49ae6858>] sock_sendmsg+0x54/0x60
[<ffffff9d49ae6f94>] ___sys_sendmsg+0x298/0x2b0
[<ffffff9d49ae98f8>] SyS_sendmsg+0xb4/0xf0
[<ffffff9d48c83770>] el0_svc_naked+0x24/0x28
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794c ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set correct size of the CIM LA dump for T6.
Fixes: 27887bc7cb ("cxgb4: collect hardware LA dumps")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
