a) should not leave crap on fault
b) should _not_ require access_ok() in any cases.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull the clockevents/clocksource tree from Daniel Lezcano:
- Convert the clocksource-probe init functions to return a value in order to
prepare the consolidation of the drivers using the DT. It is a big patchset
but went through 01.org (kbuild bot), linux next and kernel-ci (continuous
integration) (Daniel Lezcano)
- Fix a bad error handling by returning the right value for cadence_ttc
(Christophe Jaillet)
- Fix typo in the Kconfig for the Samsung pwm (Alexandre Belloni)
- Change functions to static for armada-370-xp and digicolor (Ben Dooks)
- Add support for the rk3399 SoC timer by adding bindings and a slight
change in the base address. Take the opportunity to add the DYNIRQ flag
(Huang Tao)
- Fix endian accessors for the Samsung pwm timer (Matthew Leach)
- Add Oxford Semiconductor RPS Dual Timer driver (Neil Armstrong)
- Add a kernel parameter to swich on/off the event stream feature of the arch
arm timer (Will Deacon)
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
pte_alloc_one{_kernel} allocate PTE_ORDER which is 0. This means that
this flag has never been actually useful here because it has always been
used only for PAGE_ALLOC_COSTLY requests.
Link: http://lkml.kernel.org/r/1464599699-30131-9-git-send-email-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull kbuild updates from Michal Marek:
- new option CONFIG_TRIM_UNUSED_KSYMS which does a two-pass build and
unexports symbols which are not used in the current config [Nicolas
Pitre]
- several kbuild rule cleanups [Masahiro Yamada]
- warning option adjustments for gcov etc [Arnd Bergmann]
- a few more small fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (31 commits)
kbuild: move -Wunused-const-variable to W=1 warning level
kbuild: fix if_change and friends to consider argument order
kbuild: fix adjust_autoksyms.sh for modules that need only one symbol
kbuild: fix ksym_dep_filter when multiple EXPORT_SYMBOL() on the same line
gcov: disable -Wmaybe-uninitialized warning
gcov: disable tree-loop-im to reduce stack usage
gcov: disable for COMPILE_TEST
Kbuild: disable 'maybe-uninitialized' warning for CONFIG_PROFILE_ALL_BRANCHES
Kbuild: change CC_OPTIMIZE_FOR_SIZE definition
kbuild: forbid kernel directory to contain spaces and colons
kbuild: adjust ksym_dep_filter for some cmd_* renames
kbuild: Fix dependencies for final vmlinux link
kbuild: better abstract vmlinux sequential prerequisites
kbuild: fix call to adjust_autoksyms.sh when output directory specified
kbuild: Get rid of KBUILD_STR
kbuild: rename cmd_as_s_S to cmd_cpp_s_S
kbuild: rename cmd_cc_i_c to cmd_cpp_i_c
kbuild: drop redundant "PHONY += FORCE"
kbuild: delete unnecessary "@:"
kbuild: mark help target as PHONY
...
I have only one patch for asm-generic in this release, this one is from
James Hogan and updates the generic system call table for renameat2
so we don't need to provide both renameat and renameat2 in newly
added architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ae81
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanup from Arnd Bergmann:
"I have only one patch for asm-generic in this release, this one is
from James Hogan and updates the generic system call table for
renameat2 so we don't need to provide both renameat and renameat2 in
newly added architectures"
* tag 'asm-generic-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: Drop renameat syscall from default list
The binary GCD algorithm is based on the following facts:
1. If a and b are all evens, then gcd(a,b) = 2 * gcd(a/2, b/2)
2. If a is even and b is odd, then gcd(a,b) = gcd(a/2, b)
3. If a and b are all odds, then gcd(a,b) = gcd((a-b)/2, b) = gcd((a+b)/2, b)
Even on x86 machines with reasonable division hardware, the binary
algorithm runs about 25% faster (80% the execution time) than the
division-based Euclidian algorithm.
On platforms like Alpha and ARMv6 where division is a function call to
emulation code, it's even more significant.
There are two variants of the code here, depending on whether a fast
__ffs (find least significant set bit) instruction is available. This
allows the unpredictable branches in the bit-at-a-time shifting loop to
be eliminated.
If fast __ffs is not available, the "even/odd" GCD variant is used.
I use the following code to benchmark:
#include <stdio.h>
#include <stdlib.h>
#include <stdint.h>
#include <string.h>
#include <time.h>
#include <unistd.h>
#define swap(a, b) \
do { \
a ^= b; \
b ^= a; \
a ^= b; \
} while (0)
unsigned long gcd0(unsigned long a, unsigned long b)
{
unsigned long r;
if (a < b) {
swap(a, b);
}
if (b == 0)
return a;
while ((r = a % b) != 0) {
a = b;
b = r;
}
return b;
}
unsigned long gcd1(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
b >>= __builtin_ctzl(b);
for (;;) {
a >>= __builtin_ctzl(a);
if (a == b)
return a << __builtin_ctzl(r);
if (a < b)
swap(a, b);
a -= b;
}
}
unsigned long gcd2(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
r &= -r;
while (!(b & r))
b >>= 1;
for (;;) {
while (!(a & r))
a >>= 1;
if (a == b)
return a;
if (a < b)
swap(a, b);
a -= b;
a >>= 1;
if (a & r)
a += b;
a >>= 1;
}
}
unsigned long gcd3(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
b >>= __builtin_ctzl(b);
if (b == 1)
return r & -r;
for (;;) {
a >>= __builtin_ctzl(a);
if (a == 1)
return r & -r;
if (a == b)
return a << __builtin_ctzl(r);
if (a < b)
swap(a, b);
a -= b;
}
}
unsigned long gcd4(unsigned long a, unsigned long b)
{
unsigned long r = a | b;
if (!a || !b)
return r;
r &= -r;
while (!(b & r))
b >>= 1;
if (b == r)
return r;
for (;;) {
while (!(a & r))
a >>= 1;
if (a == r)
return r;
if (a == b)
return a;
if (a < b)
swap(a, b);
a -= b;
a >>= 1;
if (a & r)
a += b;
a >>= 1;
}
}
static unsigned long (*gcd_func[])(unsigned long a, unsigned long b) = {
gcd0, gcd1, gcd2, gcd3, gcd4,
};
#define TEST_ENTRIES (sizeof(gcd_func) / sizeof(gcd_func[0]))
#if defined(__x86_64__)
#define rdtscll(val) do { \
unsigned long __a,__d; \
__asm__ __volatile__("rdtsc" : "=a" (__a), "=d" (__d)); \
(val) = ((unsigned long long)__a) | (((unsigned long long)__d)<<32); \
} while(0)
static unsigned long long benchmark_gcd_func(unsigned long (*gcd)(unsigned long, unsigned long),
unsigned long a, unsigned long b, unsigned long *res)
{
unsigned long long start, end;
unsigned long long ret;
unsigned long gcd_res;
rdtscll(start);
gcd_res = gcd(a, b);
rdtscll(end);
if (end >= start)
ret = end - start;
else
ret = ~0ULL - start + 1 + end;
*res = gcd_res;
return ret;
}
#else
static inline struct timespec read_time(void)
{
struct timespec time;
clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &time);
return time;
}
static inline unsigned long long diff_time(struct timespec start, struct timespec end)
{
struct timespec temp;
if ((end.tv_nsec - start.tv_nsec) < 0) {
temp.tv_sec = end.tv_sec - start.tv_sec - 1;
temp.tv_nsec = 1000000000ULL + end.tv_nsec - start.tv_nsec;
} else {
temp.tv_sec = end.tv_sec - start.tv_sec;
temp.tv_nsec = end.tv_nsec - start.tv_nsec;
}
return temp.tv_sec * 1000000000ULL + temp.tv_nsec;
}
static unsigned long long benchmark_gcd_func(unsigned long (*gcd)(unsigned long, unsigned long),
unsigned long a, unsigned long b, unsigned long *res)
{
struct timespec start, end;
unsigned long gcd_res;
start = read_time();
gcd_res = gcd(a, b);
end = read_time();
*res = gcd_res;
return diff_time(start, end);
}
#endif
static inline unsigned long get_rand()
{
if (sizeof(long) == 8)
return (unsigned long)rand() << 32 | rand();
else
return rand();
}
int main(int argc, char **argv)
{
unsigned int seed = time(0);
int loops = 100;
int repeats = 1000;
unsigned long (*res)[TEST_ENTRIES];
unsigned long long elapsed[TEST_ENTRIES];
int i, j, k;
for (;;) {
int opt = getopt(argc, argv, "n:r:s:");
/* End condition always first */
if (opt == -1)
break;
switch (opt) {
case 'n':
loops = atoi(optarg);
break;
case 'r':
repeats = atoi(optarg);
break;
case 's':
seed = strtoul(optarg, NULL, 10);
break;
default:
/* You won't actually get here. */
break;
}
}
res = malloc(sizeof(unsigned long) * TEST_ENTRIES * loops);
memset(elapsed, 0, sizeof(elapsed));
srand(seed);
for (j = 0; j < loops; j++) {
unsigned long a = get_rand();
/* Do we have args? */
unsigned long b = argc > optind ? strtoul(argv[optind], NULL, 10) : get_rand();
unsigned long long min_elapsed[TEST_ENTRIES];
for (k = 0; k < repeats; k++) {
for (i = 0; i < TEST_ENTRIES; i++) {
unsigned long long tmp = benchmark_gcd_func(gcd_func[i], a, b, &res[j][i]);
if (k == 0 || min_elapsed[i] > tmp)
min_elapsed[i] = tmp;
}
}
for (i = 0; i < TEST_ENTRIES; i++)
elapsed[i] += min_elapsed[i];
}
for (i = 0; i < TEST_ENTRIES; i++)
printf("gcd%d: elapsed %llu\n", i, elapsed[i]);
k = 0;
srand(seed);
for (j = 0; j < loops; j++) {
unsigned long a = get_rand();
unsigned long b = argc > optind ? strtoul(argv[optind], NULL, 10) : get_rand();
for (i = 1; i < TEST_ENTRIES; i++) {
if (res[j][i] != res[j][0])
break;
}
if (i < TEST_ENTRIES) {
if (k == 0) {
k = 1;
fprintf(stderr, "Error:\n");
}
fprintf(stderr, "gcd(%lu, %lu): ", a, b);
for (i = 0; i < TEST_ENTRIES; i++)
fprintf(stderr, "%ld%s", res[j][i], i < TEST_ENTRIES - 1 ? ", " : "\n");
}
}
if (k == 0)
fprintf(stderr, "PASS\n");
free(res);
return 0;
}
Compiled with "-O2", on "VirtualBox 4.4.0-22-generic #38-Ubuntu x86_64" got:
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 10174
gcd1: elapsed 2120
gcd2: elapsed 2902
gcd3: elapsed 2039
gcd4: elapsed 2812
PASS
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 9309
gcd1: elapsed 2280
gcd2: elapsed 2822
gcd3: elapsed 2217
gcd4: elapsed 2710
PASS
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 9589
gcd1: elapsed 2098
gcd2: elapsed 2815
gcd3: elapsed 2030
gcd4: elapsed 2718
PASS
zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
gcd0: elapsed 9914
gcd1: elapsed 2309
gcd2: elapsed 2779
gcd3: elapsed 2228
gcd4: elapsed 2709
PASS
[akpm@linux-foundation.org: avoid #defining a CONFIG_ variable]
Signed-off-by: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.
This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.
[akpm@linux-foundation.org: fix mips]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dtc dependency is missing, thus dtc is not built before it's invoked,
resulting in the following problem:
linux-2.6$ make 10m50_defconfig && make 10m50_devboard.dtb
[...]
scripts/kconfig/conf --silentoldconfig Kconfig
DTC arch/nios2/boot/10m50_devboard.dtb
/bin/sh: 1: ./scripts/dtc/dtc: not found
arch/nios2/boot/Makefile:52: recipe for target 'arch/nios2/boot/10m50_devboard.dtb' failed
make[1]: *** [arch/nios2/boot/10m50_devboard.dtb] Error 127
arch/nios2/Makefile:57: recipe for target '10m50_devboard.dtb' failed
make: *** [10m50_devboard.dtb] Error 2
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
The extra CFLAGS required for correct operation of the toolchain are not
propagated into the libgcc detection code. In case of the compiler from
poky sdk, these extra CFLAGS contain the location of compiler sysroot
(the --sysroot= option) and without this option, the location of libgcc
is not properly reported. Add the missing CFLAGS to address this issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
- virt_to_page/page_address optimisations
- Support for NUMA systems described using device-tree
- Support for hibernate/suspend-to-disk
- Proper support for maxcpus= command line parameter
- Detection and graceful handling of AArch64-only CPUs
- Miscellaneous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXNbgkAAoJELescNyEwWM0PtcIAK11xaOMmSqXz8fcTeNLw4dS
taaPWhjCYus8EhJyvTetfwk74+qVApdvKXKNKgODJXQEjeQx2brdUfbQZb31DTGT
798UYCAyEYCWkXspqi+/dpZEgUGPYH7uGOu2eDd19+PhTeX/EQSRX3fC9k0BNhvh
PN9pOgRcKAlIExZ6QYmT0g56VLtbCfFShN41mQ8HdpShl6pPJuhQ+kDDzudmRjuD
11/oYuOaVTnwbPuXn+sjOrWvMkfINHI70BAQnnBs0v+5c45mzpqEMsy0dYo2Pl2m
ar5lUFVIZggQkiqcOzqBzEgF+4gNw4LUu1DgK6cNKNMtL6k8E9zeOZMWeSVr0lg=
=bT5E
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- virt_to_page/page_address optimisations
- support for NUMA systems described using device-tree
- support for hibernate/suspend-to-disk
- proper support for maxcpus= command line parameter
- detection and graceful handling of AArch64-only CPUs
- miscellaneous cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: do not enforce strict 16 byte alignment to stack pointer
arm64: kernel: Fix incorrect brk randomization
arm64: cpuinfo: Missing NULL terminator in compat_hwcap_str
arm64: secondary_start_kernel: Remove unnecessary barrier
arm64: Ensure pmd_present() returns false after pmd_mknotpresent()
arm64: Replace hard-coded values in the pmd/pud_bad() macros
arm64: Implement pmdp_set_access_flags() for hardware AF/DBM
arm64: Fix typo in the pmdp_huge_get_and_clear() definition
arm64: mm: remove unnecessary EXPORT_SYMBOL_GPL
arm64: always use STRICT_MM_TYPECHECKS
arm64: kvm: Fix kvm teardown for systems using the extended idmap
arm64: kaslr: increase randomization granularity
arm64: kconfig: drop CONFIG_RTC_LIB dependency
arm64: make ARCH_SUPPORTS_DEBUG_PAGEALLOC depend on !HIBERNATION
arm64: hibernate: Refuse to hibernate if the boot cpu is offline
arm64: kernel: Add support for hibernate/suspend-to-disk
PM / Hibernate: Call flush_icache_range() on pages restored in-place
arm64: Add new asm macro copy_page
arm64: Promote KERNEL_START/KERNEL_END definitions to a header file
arm64: kernel: Include _AC definition in page.h
...
The newer renameat2 syscall provides all the functionality provided by
the renameat syscall and adds flags, so future architectures won't need
to include renameat.
Therefore drop the renameat syscall from the generic syscall list unless
__ARCH_WANT_RENAMEAT is defined by the architecture's unistd.h prior to
including asm-generic/unistd.h, and adjust all architectures using the
generic syscall list to define it so that no in-tree architectures are
affected.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: nios2-dev@lists.rocketboards.org
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Depending on the size of the area to be memset'ed, the nios2 memset implementation
either uses a naive loop (for buffers smaller or equal than 8 bytes) or a more optimized
implementation (for buffers larger than 8 bytes). This implementation does 4-byte stores
rather than 1-byte stores to speed up memset.
However, we discovered that on our nios2 platform, memset() was not properly setting the
buffer to the expected value. A memset of 0xff would not set the entire buffer to 0xff, but to:
0xff 0x00 0xff 0x00 0xff 0x00 0xff 0x00 ...
Which is obviously incorrect. Our investigation has revealed that the problem lies in the
incorrect constraints used in the inline assembly.
The following piece of assembly, from the nios2 memset implementation, is supposed to
create a 4-byte value that repeats 4 times the 1-byte pattern passed as memset argument:
/* fill8 %3, %5 (c & 0xff) */
" slli %4, %5, 8\n"
" or %4, %4, %5\n"
" slli %3, %4, 16\n"
" or %3, %3, %4\n"
However, depending on the compiler and optimization level, this code might be compiled as:
34: 280a923a slli r5,r5,8
38: 294ab03a or r5,r5,r5
3c: 2808943a slli r4,r5,16
40: 2148b03a or r4,r4,r5
This is wrong because r5 gets used both for %5 and %4, which leads to the final pattern
stored in r4 to be 0xff00ff00 rather than the expected 0xffffffff.
%4 is defined with the "=r" constraint, i.e as an output operand. However, as explained in
http://www.ethernut.de/en/documents/arm-inline-asm.html, this does not prevent gcc from
using the same register for an output operand (%4) and input operand (%5). By using the
constraint modifier '&', we indicate that the register should be used for output only. With this
change, we get the following assembly output:
34: 2810923a slli r8,r5,8
38: 4150b03a or r8,r8,r5
3c: 400e943a slli r7,r8,16
40: 3a0eb03a or r7,r7,r8
Which correctly produces the 0xffffffff pattern when 0xff is passed as the memset() pattern.
It is worth mentioning the observed consequence of this bug: we were hitting the kernel
BUG() in mm/bootmem.c:__free() that verifies when marking a page as free that it was
previously marked as occupied (i.e that the bit was set to 1). The entire bootmem bitmap is
set to 0xff bit via a memset() during the bootmem initialization. The bootmem_free() call right
after the initialization was finding some bits to be set to 0, which didn't make sense since the
bitmap has just been memset'ed to 0xff. Except that due to the bug explained above, the
bitmap was in fact initialized to 0xff00ff00.
Thanks to Marek Vasut for his help and feedback.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ley Foon Tan <lftan@altera.com>
This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.
Cc: Michael Büsch <m@bues.ch>
Cc: nios2-dev@lists.rocketboards.org
Acked-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To align with other architectures, the expression produced by expanding
the macro page_to_virt() should be of type void*, since it returns a
virtual address. Fix that, and also fix up an instance where page_to_virt
was expected to return 'unsigned long', and drop another instance that was
entirely unused (page_to_bus)
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 2aedcd098a ('kbuild: suppress annoying "... is up to
date." message'), $(call if_changed,...) is evaluated to "@:"
when there is nothing to do.
We no longer need to add "@:" after $(call if_changed,...) to
suppress "... is up to date." message.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
nios2 builds fail with the following build error.
arch/nios2/kernel/prom.c: In function 'early_init_dt_scan_serial':
arch/nios2/kernel/prom.c💯2: error:
implicit declaration of function 'fdt_translate_address'
Commit c90fe9c039 ("of: earlycon: Move address translation to
of_setup_earlycon()") replaced fdt_translate_address() with
of_flat_dt_translate_address() but missed updating the nios2 code.
Fixes: c90fe9c039 ("of: earlycon: Move address translation to of_setup_earlycon()")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Ley Foon Tan <lftan@altera.com>
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates all instances of csum_tcpudp_magic and
csum_tcpudp_nofold to reflect the types that are usually used as the source
inputs. For example the protocol field is populated based on nexthdr which
is actually an unsigned 8 bit value. The length is usually populated based
on skb->len which is an unsigned integer.
This addresses an issue in which the IPv6 function csum_ipv6_magic was
generating a checksum using the full 32b of skb->len while
csum_tcpudp_magic was only using the lower 16 bits. As a result we could
run into issues when attempting to adjust the checksum as there was no
protocol agnostic way to update it.
With this change the value is still truncated as many architectures use
"(len + proto) << 8", however this truncation only occurs for values
greater than 16776960 in length and as such is unlikely to occur as we stop
the inner headers at ~64K in size.
I did have to make a few minor changes in the arm, mn10300, nios2, and
score versions of the function in order to support these changes as they
were either using things such as an OR to combine the protocol and length,
or were using ntohs to convert the length which would have truncated the
value.
I also updated a few spots in terms of whitespace and type differences for
the addresses. Most of this was just to make sure all of the definitions
were in sync going forward.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__HAVE_ARCH_MEMMOVE and __HAVE_ARCH_MEMSET are unconditionally defined
for nios2, so there is no need to protect the function definitions of
memmove() and memset().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>
The generic __xchg() implementation present in asm-generic/cmpxchg.h is
correct on nios2 and even generates the same code. Switch to this generic
implementation to trim down the amount of ad-hoc copies of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Ley Foon Tan <lftan@altera.com>
Fix the following compiler splat by adding __maybe_unused annotation to
the variable. Using this particular annotation has the least ugly impact
on the code compared to using ifdeffery.
arch/nios2/kernel/setup.c: In function 'nios2_boot_init':
arch/nios2/kernel/setup.c:107:7: warning: unused variable 'cmdline_passed' [-Wunused-variable]
char cmdline_passed[COMMAND_LINE_SIZE] = { 0, };
^
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Ley Foon Tan <lftan@altera.com>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Max10 is a FPGA device. This patch adds defconfig based on Max10 hardware
reference design. Design is intended to run on Max10 development kit.
Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Max10 is a FPGA device. This patch adds Nios2 support for Max10.
This device tree is based on Max10 hardware reference design.
Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Removed some statistic counters to improve the performance of the handler.
Signed-off-by: Bernd Weiberg <bernd.weiberg@siemens.com>
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Migrate nios2 driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now.
This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED.
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: nios2-dev@lists.rocketboards.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ley Foon Tan <lftan@altera.com>
Commit 2ae416b142 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added the x86 implementation of word-at-a-time to the
generic version, which previously only supported big-endian.
Omitted the x86-specific load_unaligned_zeropad(), which in
any case is also not present for the existing BE-only
implementation of a word-at-a-time, and is only used under
CONFIG_DCACHE_WORD_ACCESS.
Added as a "generic-y" to the Kbuilds of all architectures
that didn't previously have it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Pull asm/scatterlist.h removal from Jens Axboe:
"We don't have any specific arch scatterlist anymore, since parisc
finally switched over. Kill the include"
* 'for-4.2/sg' of git://git.kernel.dk/linux-block:
remove scatterlist.h generation from arch Kbuild files
remove <asm/scatterlist.h>
CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu). This includes remapping
the vDSO to the place it has at checkpoint time.
However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service. So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.
This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold. The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.
This patch (of 3):
This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)
The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.
The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.
In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
