- CONFIG_MEMSIZE is in bytes on fusion.
- FB_BASE and FB_TOP are finer grained.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
MC_VM_FB_LOCATION is at a different offset between r6xx and r7xx/evergreen.
The location is needed for vram setup on fusion chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
System specific spread spectrum overrides can be specified in
the integrated system info table for Fusion APUs. This adds
support for using those overrides.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Should improve performance slightly and possibly fix some
issues.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we conflated intel_sdvo->is_hdmi with both having HDMI support on the
ADD along with having HDMI support on the monitor, we would attempt to
use HDMI encodings even if the interface did not support those commands.
Reported-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
We were reading our 64-bit value in I915_READ64 and returning 32 bits
of it. The restoration of fence regs at resume then had a zero end
value, and the fence had no effect.
Version 2: Split register access functions into per-size versions
Sharing code between different sizes seemed reasonable when we only
needed a single copy, but as 64-bit access requires its own version,
it makes sense to just split them out for each size.
Reported-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: use a macro to create the various read/write routines]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This has proven sufficient to recover from a hang of the GPU using the
gem_bad_blit test while at the KMS console then starting X. When
attempting the same during an X session, the timer doesn't appear to
trigger.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It isn't used for the hangcheck, which does its work right from the
timer trigger, but hangcheck can lead to error state recording, which
is run off of the workqueue.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to diagnose mysterious errors on resume, capture the
display register contents as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pinned buffers are useful for diagnosing errors in setting up state
for the chipset, which may not necessarily be 'active' at the time of
the error, e.g. the cursor buffer object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than re-implementing in the Radeon driver,
Use the execbuf / cs / pushbuf utilities that comes with TTM.
This comes with an even greater benefit now that many spinlocks have been
optimized away...
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch attempts to fix up shortcomings with the current calling
sequences.
1) There's a fastpath where no locking occurs and only io_mem_reserved is
called to obtain needed info for mapping. The fastpath is set per
memory type manager.
2) If the fastpath is disabled, io_mem_reserve and io_mem_free will be exactly
balanced and not called recursively for the same struct ttm_mem_reg.
3) Optionally the driver can choose to enable a per memory type manager LRU
eviction mechanism that, when io_mem_reserve returns -EAGAIN will attempt
to kill user-space mappings of memory in that manager to free up needed
resources
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rather than having the driver supply the validation sequence, leave that
responsibility to TTM. This saves some confusion and a function argument.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Drastically reduce the number of spin lock / unlock operations by performing
unreserving and fencing under global locks.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <j.glisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The bo lock used only to protect the bo sync object members, and since it
is a per bo lock, fencing a buffer list will see a lot of locks and unlocks.
Replace it with a per-device lock that protects the sync object members on
*all* bos. Reading and setting these members will always be very quick, so
the risc of heavy lock contention is microscopic. Note that waiting for
sync objects will always take place outside of this lock.
The bo device fence lock will eventually be replaced with a seqlock /
rcu mechanism so we can determine that a bo is idle under a
rcu / read seqlock.
However this change will allow us to batch fencing and unreserving of
buffers with a minimal amount of locking.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add an aid for the driver to detect deadlocks on multi-bo reservations
Update documentation.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Avoid the ttm_bo_unreserve() spinlocks by calling
ttm_eu_backoff_reservation_locked under the lru spinlock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Makes it possible to reserve a list of buffer objects with a single
spin lock / unlock if there is no contention.
Should improve cpu usage on SMP kernels.
v2: Initialize private list members on reserve and don't call
ttm_bo_list_ref_sub() with zero put_count.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I had removed this when I switched the atom indirect io methods
to use the io bar rather than the mmio bar, but it appears it's
still needed.
Reported-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the vblank irq handler, calls to actual vblank handling,
or at least drm_handle_vblank(), need to happen before
calls to radeon_crtc_handle_flip().
Reason: The high precision pageflip timestamping
and some other pageflip optimizations will need the updated
vblank count and timestamps for the current vblank interval.
These are calculated in drm_handle_vblank(), therefore it
must go first.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for dri2 pageflipping.
v2: precision updates from Mario Kleiner.
v3: Multihead fixes from Mario Kleiner; missing crtc offset
add note about update pending bit on pre-avivo chips
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds new functions for use by the drm core:
.get_vblank_timestamp() provides a precise timestamp
for the end of the most recent (or current) vblank
interval of a given crtc, as needed for the DRI2
implementation of the OML_sync_control extension.
It is a thin wrapper around the drm function
drm_calc_vbltimestamp_from_scanoutpos() which does
almost all the work and is shared across drivers.
.get_scanout_position() provides the current horizontal
and vertical video scanout position and "in vblank"
status of a given crtc, as needed by the drm for use by
drm_calc_vbltimestamp_from_scanoutpos().
The function is also used by the dynamic gpu reclocking
code to determine when it is safe to reclock inside vblank.
For that purpose radeon_pm_in_vbl() is modified to
accomodate a small change in the function prototype of
the radeon_get_crtc_scanoutpos() which is hooked up to
.get_scanout_position().
This code has been tested on AVIVO hardware, a RV530
(ATI Mobility Radeon X1600) in a Intel Core-2 Duo MacBookPro
and some R600 variant (FireGL V7600) in a single cpu
AMD Athlon 64 PC.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DRI2 swap & sync implementation needs precise
vblank counts and precise timestamps corresponding
to those vblank counts. For conformance to the OpenML
OML_sync_control extension specification the DRM
timestamp associated with a vblank count should
correspond to the start of video scanout of the first
scanline of the video frame following the vblank
interval for that vblank count.
Therefore we need to carry around precise timestamps
for vblanks. Currently the DRM and KMS drivers generate
timestamps ad-hoc via do_gettimeofday() in some
places. The resulting timestamps are sometimes not
very precise due to interrupt handling delays, they
don't conform to OML_sync_control and some are wrong,
as they aren't taken synchronized to the vblank.
This patch implements support inside the drm core
for precise and robust timestamping. It consists
of the following interrelated pieces.
1. Vblank timestamp caching:
A per-crtc ringbuffer stores the most recent vblank
timestamps corresponding to vblank counts.
The ringbuffer can be read out lock-free via the
accessor function:
struct timeval timestamp;
vblankcount = drm_vblank_count_and_time(dev, crtcid, ×tamp).
The function returns the current vblank count and
the corresponding timestamp for start of video
scanout following the vblank interval. It can be
used anywhere between enclosing drm_vblank_get(dev, crtcid)
and drm_vblank_put(dev,crtcid) statements. It is used
inside the drmWaitVblank ioctl and in the vblank event
queueing and handling. It should be used by kms drivers for
timestamping of bufferswap completion.
The timestamp ringbuffer is reinitialized each time
vblank irq's get reenabled in drm_vblank_get()/
drm_update_vblank_count(). It is invalidated when
vblank irq's get disabled.
The ringbuffer is updated inside drm_handle_vblank()
at each vblank irq.
2. Calculation of precise vblank timestamps:
drm_get_last_vbltimestamp() is used to compute the
timestamp for the end of the most recent vblank (if
inside active scanout), or the expected end of the
current vblank interval (if called inside a vblank
interval). The function calls into a new optional kms
driver entry point dev->driver->get_vblank_timestamp()
which is supposed to provide the precise timestamp.
If a kms driver doesn't implement the entry point or
if the call fails, a simple do_gettimeofday() timestamp
is returned as crude approximation of the true vblank time.
A new drm module parameter drm.timestamp_precision_usec
allows to disable high precision timestamps (if set to
zero) or to specify the maximum acceptable error in
the timestamps in microseconds.
Kms drivers could implement their get_vblank_timestamp()
function in a gpu specific way, as long as returned
timestamps conform to OML_sync_control, e.g., by use
of gpu specific hardware timestamps.
Optionally, kms drivers can simply wrap and use the new
utility function drm_calc_vbltimestamp_from_scanoutpos().
This function calls a new optional kms driver function
dev->driver->get_scanout_position() which returns the
current horizontal and vertical video scanout position
of the crtc. The scanout position together with the
drm_display_timing of the current video mode is used
to calculate elapsed time relative to start of active scanout
for the current video frame. This elapsed time is subtracted
from the current do_gettimeofday() time to get the timestamp
corresponding to start of video scanout. Currently
non-interlaced, non-doublescan video modes, with or
without panel scaling are handled correctly. Interlaced/
doublescan modes are tbd in a future patch.
3. Filtering of redundant vblank irq's and removal of
some race-conditions in the vblank irq enable/disable path:
Some gpu's (e.g., Radeon R500/R600) send spurious vblank
irq's outside the vblank if vblank irq's get reenabled.
These get detected by use of the vblank timestamps and
filtered out to avoid miscounting of vblanks.
Some race-conditions between the vblank irq enable/disable
functions, the vblank irq handler and the gpu itself (updating
its hardware vblank counter in the "wrong" moment) are
fixed inside vblank_disable_and_save() and
drm_update_vblank_count() by use of the vblank timestamps and
a new spinlock dev->vblank_time_lock.
The time until vblank irq disable is now configurable via
a new drm module parameter drm.vblankoffdelay to allow
experimentation with timeouts that are much shorter than
the current 5 seconds and should allow longer vblank off
periods for better power savings.
Followup patches will use these new functions to
implement precise timestamping for the intel and radeon
kms drivers.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Under KMS, restoring the cursor is handled upon modeswitch in order to
avoid enabling an undefined set of registers. At the moment, the cursor
is restored before the aperture and modes are fully setup causing some
invalid access during resume, such as:
PGTBL_ER: 0x00040000
Invalid GTT entry during Cursor Fetch
Fix this by only performing cursor register save/restore under UMS where
it is done in the correct sequence.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 2549d6c2 removed the vmalloc used for temporary storage of the
relocation lists used during execbuffer. However, our use of vmalloc was
being protected by an integer overflow check which we do want to
preserve!
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Disable FBC on Ironlake to save 1W
drm/i915: Take advantage of auto-polling CRT hotplug detection on PCH hardware
drm/i915/crt: Introduce struct intel_crt
drm/i915: Do not hold mutex when faulting in user addresses
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
drm/i915: Retire any pending operations on the old scanout when switching
drm/i915: Fix I2C adapter registration
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (40 commits)
drm/radeon/kms: i2c s/sprintf/snprintf/g for safety
drm/radeon/kms: fix i2c pad masks on rs4xx
drm/ttm: Fix up a theoretical deadlock
drm/radeon/kms: fix tiling info on evergreen
drm/radeon/kms: fix alignment when allocating buffers
drm/vmwgfx: Fix up an error path during bo creation
drm/radeon/kms: register an i2c adapter name for the dp aux bus
drm/radeon/kms/atom: add proper external encoders support
drm/radeon/kms/atom: cleanup and unify DVO handling
drm/radeon/kms: properly power up/down the eDP panel as needed (v4)
drm/radeon/kms/atom: set sane defaults in atombios_get_encoder_mode()
drm/radeon/kms: turn the backlight off explicitly for dpms
drm/radeon/kms: fix typo in r600 cs checker
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
...
Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We will use this structure in future patches to store CRT specific
information on the encoder.
Split out and tweaked from a patch by Keith Packard.
Signed-off-by: Keith Packard <keithp@kithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Linus Torvalds found that it was rather trivial to trigger a system
freeze:
In fact, with lockdep, I don't even need to do the sysrq-d thing: it
shows the bug as it happens. It's the X server taking the same lock
recursively.
Here's the problem:
=============================================
[ INFO: possible recursive locking detected ]
2.6.37-rc2-00012-gbdbd01a #7
---------------------------------------------
Xorg/2816 is trying to acquire lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c626c>] i915_gem_fault+0x50/0x17e
but task is already holding lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
other info that might help us debug this:
2 locks held by Xorg/2816:
#0: (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
#1: (&mm->mmap_sem){++++++}, at: [<ffffffff81022d4f>] page_fault+0x156/0x37b
This recursion was introduced by rearranging the locking to avoid the
double locking on the fast path (4f27b5d and fbd5a26d) and the
introduction of the prefault to encourage the fast paths (b5e4f2b). In
order to undo the problem, we rearrange the code to perform the access
validation upfront, attempt to prefault and then fight for control of the
mutex. the best case scenario where the mutex is uncontended the
prefaulting is not wasted.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As per advice from Jean Delvare.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A process suspended waiting for a higher sequence or no sequence to unreserve,
a bo may be beaten to the reservation by a process with a lower sequence.
In that case the first process should give up trying to reserve and
return -EAGAIN. In order for that to happen, we must wake waiting processes
when we change sequence, so that they have a chance to detect the new
sequence.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: (25 commits)
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
drm/nouveau: Return error from nouveau_gpuobj_new if we're out of RAMIN.
drm/nouveau: Fix compilation issues in nouveau_pm when CONFIG_HWMON is not set
drm/nouveau: Don't use load detection for connector polling.
drm/nv10-nv20: Fix instability after MPLL changes.
drm/nv50: implement possible workaround for NV86 PGRAPH TLB flush hang
drm/nouveau: Don't poll LVDS outputs.
drm/nouveau: Use "force" to decide if analog load detection is ok or not.
drm/nv04: Fix scanout over the 16MB mark.
drm/nouveau: fix nv40 pcie gart size
drm/nva3: fix overflow in fixed point math used for pll calculation
drm/nv10: Balance RTs expected to be accessed simultaneously by the 3d engine.
drm/nouveau: Expose some BO usage flags to userspace.
drm/nouveau: Reduce severity of the unknown getparam error.
drm/nouveau: Avoid lock dependency between ramht and ramin spinlocks.
drm/nouveau: Some random cleanups.
...
We aren't currently using tiling in userspace on evergreen,
but the info we currently return for the tiling info query
(gb_addr_config) is no adequate for userspace tiling alignment
calculations. It does not contain the bank info. Create a custom
tiling info dword with all the necessary info (num channels,
num banks, group size, row size).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This causes the connector to not be added since i2c init fails
for the adapter. Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31688
Noticed by Ari Savolainen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Ari Savolainen <ari.m.savolainen@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are external encoder chips connected via DVO or DP.
The actual external encoder programming is handled by the
kms encoder functions for primary encoder.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Handle all the various asic family specific things for DVO.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The eDP panel must be powered up for aux transactions, so power it
up for detect and mode probe functions, otherwise power it up or
down based on dpms.
v2:
- only mess with eDP panel on DCE4+
- only mess with eDP panel on eDP connectors, not all DP connectors
v3:
- be extra careful to only mess with eDP panels on eDP connectors
v4:
- avoid possible null derefernce if a connector has not been
assigned to the encoder
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there was no connector mapped to the encoder, atombios_get_encoder_mode()
returned 0 which is the id for DP. Return something sane instead based on
the encoder id. This avoids hitting the DP paths on non-DP encoders.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like a typo in:
drm/radeon/r600: fix tiling issues in CS checker.
(f30df2fad0)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case. Change this to -EINVAL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures. Previously, the
calculations where inconsistent for each buffer type.
- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code generated an interrupt storm bad enough to completely
take down my system.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Avoid confusing userspace by not publishing backlight controls if ACPI
equivalents are available.
Reported-by: Aaron Sowry <aaron@aeneby.se>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Improvements:
- Fix bug in switch statement
- Add parts of 0x10022c, 0x10023c
- Clean up 0x100234
- Comment out assumption in 0x100228 until verified
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Tomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Tomas Miljenovic <tomasmiljenovic@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Analog output polling makes GL programs jerky when pageflip is being
used because it's carried out with the mode_config mutex held.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Nouveau sets the PCIE GART size to 64MiB for all cards before nv50,
but nv40 has enough RAMIN space to support 512MiB GART size. This
patch fixes this value to make use of this hardware capability.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will be needed for Z compression and to take smarter placement
decisions.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The ramht code called some gpuobj functions with the HARDIRQ-safe
RAMHT spinlock held, this could potentially lead to a dead lock
because ramin_lock is HARDIRQ-unsafe.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Remove some unused/duplicated definitions and make sparse happy again.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows the user to set a mode larger than the native one, useful
if we had trouble finding the actual native mode (e.g. because it goes
above the hardware bandwidth limits).
Reported-by: Grzesiek Sójka <pld@pfu.pl>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There are two messages in the ISR of nouveau which might be printed out
hundred times in a second. Ratelimit them. (We need to move
nouveau_ratelimit to the top of the file.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
backlight_device_register has been expecting a const "ops" argument, and using
it as such, since 9905a43b2d. Let's make the
remaining backlight_ops instances const.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As we may bind an object with the correct alignment, but with an invalid
size, it may pass the current checks on whether the object may be reused
with a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
g33/pineview doesn't have any alignment constrains for unfenced tiled
buffers. But older chips have. Fix this.
Problem introduced in a00b10c360.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
enable_vblank implementations should use negative result to indicate error.
radeon_enable_vblank() returns EINVAL in this case. Change this to -EINVAL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tiled buffers have the same alignment requirements regardless of
whether the surface is for db, cb, or textures. Previously, the
calculations where inconsistent for each buffer type.
- Unify the alignment calculations in a common function
- Standardize the alignment units (pixels for pitch/height/depth,
bytes for base)
- properly check the buffer base alignments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
An old and oft reported bug, is that of the GPU hanging on a
MI_WAIT_FOR_EVENT following a mode switch. The cause is that the GPU is
waiting on a scanline counter on an inactive pipe, and so waits for a
very long time until eventually the user reboots his machine.
We can prevent this either by moving the WAIT into the kernel and
thereby incurring considerable cost on every swapbuffers, or by waiting
for the GPU to retire the last batch that accesses the framebuffer
before installing a new one. As mode switches are much rarer than swap
buffers, this looks like an easy choice.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28964
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29252
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before reading ring register, set FORCE_WAKE bit to prevent GT core
power down to low power state, otherwise we may read stale values.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[ickle: added a udelay which seemed to do the trick on my SNB]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We use i915_gem_object_get_fence_reg() to do LRU tracking of the fence
registers, so stop trying to be too clever when pinning the fb->obj.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Call destroy() on _all_ ttm_bo_init() failures, and make sure that
behavior is documented in the function description.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If ttm_bo_init() returns failure, it already destroyed the BO, so we need to
retry from scratch.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix many small bugs in I2C adapter registration:
* Properly reject unsupported GPIO pin.
* Fix improper use of I2C_NAME_SIZE (which is the size of
i2c_client.name, not i2c_adapter.name.)
* Prefix adapter names with "i915" so that the user knows what the
I2C channel is connected to.
* Fix swapped characters in the string used to name the GPIO-based
adapter.
* Add missing comma in gmbus name table.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Temperature is not shifted as on newer asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
2b5b1d7da9583484b3a9e7e375a90ca0e8ca07c2
(drm/radeon/kms: add support for clock/data path routers)
That patch completed mux support for ddc and cd line routing
between connectors. This patch fixes an indexing typo that was
resulting in the atom bios router objects not always being walked,
ensures the validity entries for the reused router structure are
reset for every connector object walked, and corrects the masking
operations used to update the mux control bits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Tyson Whitehead <twhitehead@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
26b5bc9864
(drm/radeon/kms: add support for router objects)
That patch added support for systems that use a mux to control
the ddc line routing between the connectors. This patch adds
support for systems that use a mux to control the encoder
clock and data path routing to the connectors.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Structure drm_vmw_fence_rep is copied to userland with field "pad64"
uninitialized. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When bo pin failed during modesetting,
vmwgfx would try to unref a non-existing buffer object.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This breaks vmwgfx non-root EGL clients and is a remnant from the
TTM user-space interface. This test should be done in the driver.
Replace the remaining placement test with a BUG_ON, since triggering
it is a driver bug.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The sync object may disappear as soon as we release the bo::lock, so
take a reference on it while we use it.
One option would be to call sync_object_flush() before releasing the bo::lock,
but that would put an atomic requirement on that function.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The A/B links aren't independantly useable on these blocks so when
we disable the encoders, make sure to only disable the encoder when
there is no connector using it.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=18564
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently an invalid EDID extension will cause the whole EDID to be considered invalid. Instead just drop the invalid extensions, and return the valid ones. The base block is modified to claim to have the number valid extensions, and the check sum is updated.
For my EIZO S2242W the base block is fine, but the extension block is all zeros. Without this patch I get no X and no VTs.
Signed-off-by: Sam Tygier <samtygier@yahoo.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make more of the connector code debug only to avoid
spamming the kernel logs with detect and add modes
messages.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver (for example vmwgfx) may want to silently deal with the
error itself.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since we're doing this outside of a spinlock to provide the necessary
barriers, add an explicit barrier.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace with BUG_ON(). These error messages remained from the time
when TTM was initialized from user-space. Nowadays hitting one of those
is really a kernel bug.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Searching for a free block in the range manager may in some situations be a
lenghty operation, and we want to avoid holding the global lru lock
during that time. Instead use a per-manager spinlock.
This leaves the global lru lock for quick lru list and swap list manipulation
only, including list manipulation associated with reserving buffer objects.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an obsolete comment about mm nodes.
Document the new bo range manager interface.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* Dave Airlie <airlied@linux.ie> wrote:
> > Lee, Chun-Yi (1):
> > gpu: Add Intel GMA500(Poulsbo) Stub Driver
Today's -tip fails to build due to upstream commit e26fd11 ("gpu: Add Intel
GMA500(Poulsbo) Stub Driver"), committed two days ago and merged yesterday, on
x86 allmodconfig with BACKLIGHT_CLASS_DEVICE disabled:
drivers/built-in.o: In function `acpi_video_bus_put_one_device':
video.c:(.text+0x7d26f): undefined reference to `backlight_device_unregister'
drivers/built-in.o: In function `acpi_video_switch_brightness':
video.c:(.text+0x7d6f5): undefined reference to `backlight_force_update'
drivers/built-in.o: In function `acpi_video_device_find_cap':
video.c:(.text+0x7dfdb): undefined reference to `backlight_device_register'
drivers/gpu/stub/Kconfig selects ACPI_VIDEO, but ACPI_VIDEO is a complex interactive
Kconfig option with a lot of dependencies:
config ACPI_VIDEO
tristate "Video"
depends on X86 && BACKLIGHT_CLASS_DEVICE && VIDEO_OUTPUT_CONTROL
depends on INPUT
select THERMAL
help
This driver implements the ACPI Extensions For Display Adapters
and if any of its dependencies are not met, we get a build failure. This problem was
apparently realized in the driver at a certain stage:
config STUB_POULSBO
tristate "Intel GMA500 Stub Driver"
depends on PCI
# Poulsbo stub depends on ACPI_VIDEO when ACPI is enabled
# but for select to work, need to select ACPI_VIDEO's dependencies, ick
select ACPI_VIDEO if ACPI
but not fully understood and not fully fixed.
As a quick fix select these secondary dependencies, like drivers/gpu/drm/Kconfig
does:
config DRM_I915
tristate "i915 driver"
depends on AGP_INTEL
select SHMEM
select DRM_KMS_HELPER
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
# i915 depends on ACPI_VIDEO when ACPI is enabled
# but for select to work, need to select ACPI_VIDEO's dependencies, ick
select VIDEO_OUTPUT_CONTROL if ACPI
select BACKLIGHT_CLASS_DEVICE if ACPI
select INPUT if ACPI
select ACPI_VIDEO if ACPI
select ACPI_BUTTON if ACPI
help
Choose this option if you have a system that has Intel 830M, 845G,
852GM, 855GM 865G or 915G integrated graphics. If M is selected, the
But it's arguably not particularly nice looking, so maybe this area of code is ripe
for a Kconfig restructuring/cleanup.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Fix LVDS fixed-mode regression from 219adae1
drm/i915/ringbuffer: Use the HEAD auto-reporting mechanism
drm/i915: Avoid might_fault during pwrite whilst holding our mutex
agp/intel: fix cache control for sandybridge
agp/intel: restore cache behavior on sandybridge
drm/i915; Don't apply Ironlake FDI clock workaround to Sandybridge
drm/i915: Fix KMS regression on Sandybridge/CPT
i915: reprogram power monitoring registers on resume
drm/i915: SNB BLT workaround
drm/i915: Fix the graphics frequency clamping at init and when IPS is active.
drm/i915: Allow powersave modparam to be adjusted at runtime.
drm/i915: Apply big hammer to serialise buffer access between rings
drm/i915: opregion_setup: iounmap correct address
drm/i915: Flush read-only buffers from the active list upon idle as well
i915: signedness bug in check_overlay_src()
drm/i915: Fix typo from "Enable DisplayPort Audio"
Commit 219adae1 cached the EDID found during LVDS init, but in the
process prevented the init routine from discovering the preferred
fixed-mode for the panel. This was causing us to guess the correct mode,
which sometimes is wide of the mark.
Reported-and-tested-by: Jon Masters <jonathan@jonmasters.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If modeset init failed we attempted to unload the module, before we
finished setting it up and so triggered various oopses.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we use POSTING_READ to flush the write to the register before
proceeding, we do not care what the return value is and similar we do
not care for the read to be recorded whilst tracing register
read/writes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These registers are written very frequently, are timing sensitive, and
not particularly relevant to any debugging, so remove the tracepoints
from these.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will be used later to hide the frequently written registers
from debug traces in order to increase the signal-to-noise.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add two tracepoints at I915_WRITE/READ for tracing down all the
register write and read.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
My Sandybridge only reports 0 for the ring buffer registers, causing it
to hang as soon as we exhaust the available ring. As a workaround, take
advantage of our huge ring buffers and use the auto-reporting mechanism
to update the status page with the HEAD location every 64 KiB.
Cherry-picked from 6aa56062ea.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31404
Tested-by: Zhao Jian <jian.j.zhao@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is not known to fix any particular bugs we have, but the spec
says to do it, and the BIOS hadn't already set it up on my system.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... and so prevent a potential circular reference:
[ INFO: possible circular locking dependency detected ]
2.6.37-rc1-uwe1+ #4
-------------------------------------------------------
Xorg/1401 is trying to acquire lock:
(&mm->mmap_sem){++++++}, at: [<c01e4ddb>] might_fault+0x4b/0xa0
but task is already holding lock:
(&dev->struct_mutex){+.+.+.}, at: [<f869c3ac>]
i915_mutex_lock_interruptible+0x3c/0x60 [i915]
which lock already depends on the new lock.
When the locking around the pwrite ioctl was simplified, I did not spot
that the phys path never took any locks and so we introduced this
potential circular reference.
Reported-by: Uwe Helm <uwe.helm@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ring buffer registers return 0 whilst idle (for some values of idle)
on early Sandybridge hw. Persevere even when all appears hopeless...
Fortunately the head auto-reporting prevents most hangs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31370
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of killing the process, just return no page found and reschedule
the process giving the GPU some time to (hopefully) recover.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
a00b10c360 "Only enforce fence limits inside the GTT" also
added a fenceable/mappable disdinction when binding/pinning buffers.
This only complicates the code with no pratical gain:
- In execbuffer this matters on for g33/pineview, as this is the only
chip that needs fences and has an unmappable gtt area. But fences
are only possible in the mappable part of the gtt, so need_fence
implies need_mappable. And need_mappable is only set independantly
with relocations which implies (for sane userspace) that the buffer
is untiled.
- The overlay code is only really used on i8xx, which doesn't have
unmappable gtt. And it doesn't support tiled buffers, currently.
- For all other buffers it's a bug to pass in a tiled bo.
In short, this disdinction doesn't have any practical gain.
I've also reverted mapping the overlay and context pages as possibly
unmappable. It's not worth being overtly clever here, all the big
gains from unmappable are for execbuf bos.
Also add a comment for a clever optimization that confused me
while reading the original patch by Chris Wilson.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In a00b10c360 "Only enforce fence limits inside the GTT"
Chris Wilson implemented an optimization to only pin framebuffers
as mappable for crtc_set_base (but not for pageflips). This breaks
the abi, eg: A double buffering mesa client might leave the last
framebuffer in unmappable space on close. A subsequent glReadPix
by a frontbuffer rendering client then goes boom. My pretty anal
mappable/unmappable consistency checking detected this, see
https://bugs.freedesktop.org/show_bug.cgi?id=31286
Chris Wilson tried to fix this in 085ce26437 by pinning
tiled framebuffers into mappable space. This
a) renders the original optimization of not forcing framebuffers
for pageflipping clients into mappable pointless because all our
scanout buffers are tiled by default.
b) doesn't solve the problem for untiled framebuffers.
So kill this. Emperically it's no gain anyway because framebuffers are
being reused by the ddx and hence there's no chance for them to get
constanly bounced between mappable and unmappable.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We should enable FDI normal training on Sandybridge/CPT system
as well.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[ickle: removed unrelated chunks]
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes issue where i915_gfx_val was reporting values several
orders of magnitude higher than physically possible (without
leaving scorch marks on my thighs at least.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When merging Daniel's full-gtt patches I had a set of tweaks which I
thought I had undone. I was half right...
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31286
Reported-by: jinjin.wang@intel.com
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I presumed that we would be writing to the batch through the GTT having
bound it, so I converted it to use iomem. Even later as I spotted that
we didn't even move the batch to the GTT (now an issue since we default
to uncached memory on SNB) I still didn't realise that using iomem for
kmapped memory was incorrect. Fix it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Immediate merge to resolve conflicts from applying a stability fix to
both branches.
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
drivers/gpu/drm/i915/intel_ringbuffer.h
On some stepping of SNB cpu, the first command to be parsed in BLT
command streamer should be MI_BATCHBUFFER_START otherwise the GPU
may hang.
(cherry picked from commit 8d19215be8)
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On some stepping of SNB cpu, the first command to be parsed in BLT
command streamer should be MI_BATCHBUFFER_START otherwise the GPU
may hang.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[ickle: rebased for -next]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Part of the issue here was that Eric slipped in a debug hack for
testing the i915 IPS code before the intel_ips.c driver had landed.
This caused the driver to always use the full range of frequencies,
which is only legal when IPS tells us we have the headroom. Once that
hack was removed, there was confusion about the driver's frequency
clamping variables: max_delay is the driver's current limit on the
highest frequency the IPS driver wants us to use, while dev_priv->fmax
is the hardware-reported limit that the IPS driver can increase up to.
Tested with IPS driver loaded or not. Note that on Ironlake systems
without the IPS driver loaded this will result in a performance
reduction, and the inital warmup of frequency limits can impact
benchmarking on systems with IPS loaded.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
[ickle: demoted a debugging printk]
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
2.6.36 appears to respect the 0400 mode we assigned to the parameter
preventing it from being adjusted after loading. However, this is safe
to adjust at runtime.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31311
Reported-by: Fernando Lemos <fernandotcl@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In case of an opregion signature mismatch in intel_opregion_setup(),
iounmap the correct address.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Take two passes to evict everything whilst searching for sufficient free
space to bind the batchbuffer. After searching for sufficient free space
using LRU eviction, evict everything that is purgeable and try again.
Only then if there is insufficient free space (or the GTT is too badly
fragmented) evict everything from the aperture and try one last time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Accessing the uninitialised obj->pages instead of the local page lead to
an OOPs.
Reported-by: Xavier Chantry <chantry.xavier@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
My Sandybridge only reports 0 for the ring buffer registers, causing it
to hang as soon as we exhaust the available ring. As a workaround, take
advantage of our huge ring buffers and use the auto-reporting mechanism
to update the status page with the HEAD location every 64 KiB.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After switching the MMIO registers to use pci_iomap, remember to dispose
of the mapping with pci_iounmap (for symmetry).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So long as we adhere to the fence registers rules for alignment and no
overlaps (including with unfenced accesses to linear memory) and account
for the tiled access in our size allocation, we do not have to allocate
the full fenced region for the object. This allows us to fight the bloat
tiling imposed on pre-i965 chipsets and frees up RAM for real use. [Inside
the GTT we still suffer the additional alignment constraints, so it doesn't
magic allow us to render larger scenes without stalls -- we need the
expanded GTT and fence pipelining to overcome those...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Also spotted by Dan Carpenter.
obj->pin_count is unsigned so the BUG_ON(obj->pin_count<0) will never
trigger.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The error code is only expected during the actual pruning and not during
the first measurement (nr_to_scan == 0) pass.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It is possible for the active list to only contain a read-only buffer so
that the ring->gpu_write_list remains entry. This leads to an
inconsistency between i915_gpu_is_active() and i915_gpu_idle() causing
an infinite spin during the shrinker and an assertion failure that
i915_gpu_idle() does indeed flush all buffers from the active lists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to force a page-fault on a GTT mapping after we start using it
from the GPU and so enforce correct CPU/GPU synchronisation, we need to
invalidate the mapping.
Pointed out by Owain G. Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By using read_cache_page() for individual pages during pwrite/pread we
can eliminate an unnecessary large allocation (and immediate free) of
obj->pages. Also this eliminates any potential nesting of get/put pages,
simplifying the code and preparing the path for greater things.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we rarely use the mmap_offset and it is easily computable from the
obj->map_list.hash, remove it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Eliminate the racy device unload by embedding a shrinker into each
device. Smaller, simpler code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Play safe and use the common routines which take care of the cachability
of the memory when setting up the iomapping for the PCI registers.
Whilst they should be cacheable for the current generations, actually
honouring what the device requires is a better long term strategy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: enable unmappable vram for evergreen
drm/radeon/kms: fix tiled db height calculation on 6xx/7xx
drm/radeon/kms: fix handling of tex lookup disable in cs checker on r2xx
Evergreen now has blit support, but unmappable vram support
was disabled in c919b371cb
(drm/radeon/kms: avoid corner case issue with unmappable vram V2)
due to merge ordering. This re-enables unmappable vram on
evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Calculate height based on the slice bitfield rather than the size.
Same as Dave's CB fix.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are cases when multiple texture units have to be enabled,
but not actually used to sample. This patch checks to see if
the lookup_disable bit is set and if so, skips the texture check.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=25544
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This holds error state from the main graphics arbiter mainly involving
the DMA engine and address translation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is the same value as before, but it just makes the code slightly
more readable to use the local variable than converting the aperture
size into bytes every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
More precisely: For those that _need_ to be mappable. Also add two
BUG_ONs in fault and pin to check the consistency of the mappable
flag.
Changes in v2:
- Add tracking of gtt mappable space (to notice mappable/unmappable
balancing issues).
- Improve the mappable working set tracking by tracking fault and pin
separately.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This way we can make some more educated guesses as to why exactly
we can't use 2G apertures to their full potential ;)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At least the part that's currently enabled by the BIOS.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In i915_gem_object_pin obviously unbind only if mappable is true.
This is the last part to enable gtt_mappable_end != gtt_size, which
the next patch will do.
v2: Fences on g33/pineview only work in the mappable part of the
gtt.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Like before add a parameter mappable (also to gem_object_pin) and
set it depending upon the context. Only bos that are brought into
the gtt due to an execbuffer call can be put into the unmappable
part of the gtt, everything else (especially pinned objects) need
to be put into the mappable part of the gtt.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a mappable parameter to i915_gem_evict_something to distinguish
the two cases (non-restricted vs. mappable gtt allocations). No
functional changes because the mappable limit is set to the end of
the gtt currently.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently, we believe the GPU is idle if just the RENDER ring is idle.
This is obviously wrong if we only using either the BLT or the BSD
rings and so masking genuine hangs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Preparing the ringbuffer for adding new commands can fail (a timeout
whilst waiting for the GPU to catch up and free some space). So check
for any potential error before overwriting HEAD with new commands, and
propagate that error back to the user where possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
"depth" should be signed in case packed_depth_bytes() returns -EINVAL.
This probably doesn't make a difference at runtime. In the original
code we would return -EINVAL later if (rec->offset_Y % 4294967274) is
non-zero.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ringbuffer keeps a pointer to the parent device, so we can use that
instead of passing around the pointer on the stack.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hi,
while I looked through your changes in drm-intel git tree (as I've got
a pressure for supporting DisplayPort audio), I stumbled on the
possible bug in the commit a9756bb5b2
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Sun Sep 19 13:09:06 2010 +0800
drm/i915: Enable DisplayPort audio
In this commit, you changed the return value of g4x_dp_detect()
to "bit", but it should be "status", I suppose.
[ickle: mea culpa.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31094
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (476 commits)
vmwgfx: Implement a proper GMR eviction mechanism
drm/radeon/kms: fix r6xx/7xx 1D tiling CS checker v2
drm/radeon/kms: properly compute group_size on 6xx/7xx
drm/radeon/kms: fix 2D tile height alignment in the r600 CS checker
drm/radeon/kms/evergreen: set the clear state to the blit state
drm/radeon/kms: don't poll dac load detect.
gpu: Add Intel GMA500(Poulsbo) Stub Driver
drm/radeon/kms: MC vram map needs to be >= pci aperture size
drm/radeon/kms: implement display watermark support for evergreen
drm/radeon/kms/evergreen: add some additional safe regs v2
drm/radeon/r600: fix tiling issues in CS checker.
drm/i915: Move gpu_write_list to per-ring
drm/i915: Invalidate the to-ring, flush the old-ring when updating domains
drm/i915/ringbuffer: Write the value passed in to the tail register
agp/intel: Restore valid PTE bit for Sandybridge after bdd3072
drm/i915: Fix flushing regression from 9af90d19f
drm/i915/sdvo: Remove unused encoding member
i915: enable AVI infoframe for intel_hdmi.c [v4]
drm/i915: Fix current fb blocking for page flip
drm/i915: IS_IRONLAKE is synonymous with gen == 5
...
Fix up conflicts in
- drivers/gpu/drm/i915/{i915_gem.c, i915/intel_overlay.c}: due to the
new simplified stack-based kmap_atomic() interface
- drivers/gpu/drm/vmwgfx/vmwgfx_drv.c: added .llseek entry due to BKL
removal cleanups.
Use Ben's new range manager hooks to implement a manager for
GMRs that manages ids rather than ranges.
This means we can use the standard TTM code for binding, unbinding and
eviction.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
broken by:
drm/radeon/r600: fix tiling issues in CS checker.
v2: only apply it to 1D tiling case.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
macro tile heights are aligned to num channels, not num banks.
Noticed by Dave Airlie.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hw stores a default clear state for registers in the context
range that can be initialized when the CP is set up. Set the
blit state as the default clear state and use the CLEAR_STATE
packet to load the blit state rather than loading it from an IB.
This reduces overhead when doing bo moves using the 3D engine.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently, there have no GMA500(Poulsbo) native video driver to support
intel opregion. So, use this stub driver to enable the acpi backlight
control sysfs entry files by requrest acpi_video_register.
[airlied: fix warnings]
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vram map in the radeon memory controller needs to be
>= the pci aperture size. Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28402
The problematic cards in the above bug have 64 MB of vram,
but the pci aperture is 128 MB and the MC vram map was only
64 MB. This can lead to hangs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Improper display watermarks can result in underflow to the display
controllers which can cause flickering or other artifacts.
This patch implements display watermark support and line buffer
allocation for evergreen asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These are needed for enabling dynamic GPR allocation in the shaders
in the userspace acceleration drivers.
v2: fix typo in reg name
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CS checker had some incorrect alignment requirements for 2D surfaces,
this made rendering to mipmap levels that were 2D broken.
Also the CB height was being worked out from the BO size, this doesn't work
at all when rendering mipmap levels, instead we work out what height userspace
wanted from slice max and use that to check it fits inside the BO, however
the DDX send the wrong slice max for an unaligned buffer so we have to workaround
for that even though its a userspace bug.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (63 commits)
drm/i915: Move gpu_write_list to per-ring
drm/i915: Invalidate the to-ring, flush the old-ring when updating domains
drm/i915/ringbuffer: Write the value passed in to the tail register
agp/intel: Restore valid PTE bit for Sandybridge after bdd3072
drm/i915: Fix flushing regression from 9af90d19f
drm/i915/sdvo: Remove unused encoding member
i915: enable AVI infoframe for intel_hdmi.c [v4]
drm/i915: Fix current fb blocking for page flip
drm/i915: IS_IRONLAKE is synonymous with gen == 5
drm/i915: Enable SandyBridge blitter ring
drm/i915/ringbuffer: Remove broken intel_fill_struct()
drm/i915/ringbuffer: Fix emit batch buffer regression from 8187a2b
drm/i915: Copy the updated reloc->presumed_offset back to the user
drm/i915: Track objects in global active list (as well as per-ring)
drm/i915: Simplify most HAS_BSD() checks
drm/i915: cache the last object lookup during pin_and_relocate()
drm/i915: Do interrupible mutex lock first to avoid locking for unreference
drivers: gpu: drm: i915: Fix a typo.
agp/intel: Also add B43.1 to list of supported devices
drm/i915: rearrange mutex acquisition for pread
...
... to prevent flush processing of an idle (or even absent) ring.
This fixes a regression during suspend from 87acb0a5.
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
When the object has been written to by the gpu it remains on the ring
until its flush has been retired. However, when the object is moving to
the ring and the associated cache needs to be invalidated, we need to
perform the flush on the target ring, not the one it came from (which is
NULL in the reported case and so the flush was entirely absent).
Reported-by: Peter Clifton <pcjc2@cam.ac.uk>
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: introduce CONFIG_BKL.
dabusb: remove the BKL
sunrpc: remove the big kernel lock
init/main.c: remove BKL notations
blktrace: remove the big kernel lock
rtmutex-tester: make it build without BKL
dvb-core: kill the big kernel lock
dvb/bt8xx: kill the big kernel lock
tlclk: remove big kernel lock
fix rawctl compat ioctls breakage on amd64 and itanic
uml: kill big kernel lock
parisc: remove big kernel lock
cris: autoconvert trivial BKL users
alpha: kill big kernel lock
isapnp: BKL removal
s390/block: kill the big kernel lock
hpet: kill BKL, add compat_ioctl
This should fix the error along the reset path were we tried to clear the
tail register by setting it to 0, but were in fact setting it to the
current value and complaining when it did not reset to 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst moving the code around in 9af90d19f, I dropped the or'ing in of
new write domains which would zero out the write domain for a render
target if later reused as a source later in the batch. This meant that
we might drop a required flush before reading from the render target.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31043
Reported-by: xunx.fang@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This block is only used when detecting whether the connector is HDMI and
never again, so scope the variable to the detection routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.
My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.
With this patch, my receiver has not lost sync yet (> 40 tries).
Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
Two questions still remain:
I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?
Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Block execbuffer for the fb to be flipped away, not the one that is to
be flipped in.
[ickle: rewritten for -next]
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on an original patch by Zhenyu Wang, this initializes the BLT ring for
SandyBridge and enables support for user execbuffers.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... before someone tries to use it. The code both calls
intel_ring_begin/advance() and open-codes the bookkeeping performed by
those two functions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In commit 8187a2b, the number of dwords used in the ringbuffer for
executing the batch buffer was erroneously changed from 2 to 4.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With all the patches we have queued in the BKL removal tree, only a
few dozen modules are left that actually rely on the BKL, and even
there are lots of low-hanging fruit. We need to decide what to do
about them, this patch illustrates one of the options:
Every user of the BKL is marked as 'depends on BKL' in Kconfig,
and the CONFIG_BKL becomes a user-visible option. If it gets
disabled, no BKL using module can be built any more and the BKL
code itself is compiled out.
The one exception is file locking, which is practically always
enabled and does a 'select BKL' instead. This effectively forces
CONFIG_BKL to be enabled until we have solved the fs/lockd
mess and can apply the patch that removes the BKL from fs/locks.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit replaces the ttm_bo_cleanup_ref function with two new functions.
One for the case where the bo is not yet on the delayed destroy list, and
one for the case where the bo was on the delayed destroy list, at least at
the time of call. This makes it possible to optimize the two cases somewhat.
It also enables the possibility to directly destroy buffers on the
delayed delete list when they are about to be evicted or swapped out.
Currently they were only evicted / swapped and destruction was left for the
delayed buffer destruction thread.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the userspace driver is using a constant relocation array with a
static buffer, they will pass the same relocation array back to the
kernel. So we *do* need to update the presumed offset value in those
relocations to reflect the current object so that they remain correct
with future batchbuffers and we avoid the necessity of having to suspend
execution and perform redundant relocations.
Fixes the regression introduced by 12f889c for applications using
absolute addressing on trees of buffer (i.e. the current consumers of
libdrm_intel.so).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30996
Reported-by: Wang, Jinjin <jinjin.wang@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
To handle retirements, we need per-ring tracking of active objects.
To handle evictions, we need global tracking of active objects.
As we enable more rings, rebuilding the global list from the individual
per-ring lists quickly grows tiresome and overly complicated. Tracking the
active objects in two lists is the lesser of two evils.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... by always initialising the empty ringbuffer it is always then safe
to check whether it is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The most frequent relocation within a batchbuffer is a contiguous sequence
of vertex buffer relocations, for which we can virtually eliminate the
drm_gem_object_lookup() overhead by caching the last handle to object
translation.
In doing so we refactor the pin and relocate retry loop out of
do_execbuffer into its own helper function and so improve the error
paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
One of the primarily consumers of the i915 driver is X, a large signal
driven application. Frequently when writing into the buffers, there is a
pending signal which causes us not to take the interruptible lock but
then we need to take that same lock around the object unreference. By
rearranging the code to do the interruptible lock as the first check, we
can avoid the frequent additional locking around the unreference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... to avoid reacquiring it to drop the object reference count on
exit. Note we have to make sure we now drop (and reacquire) the lock
around acquiring the mm semaphore on the slow paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After allocation a handle for the fresh object, we know that we can
safely drop the refcnt without triggering a free so we do not need the
mutex. Strangely, this mutex acquisition is the one that appears on
driver profiles.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid an early eviction of the batch buffer into the uncached GTT
domain, and so do the relocation fixup in cacheable memory.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... perform an access validation check up front instead and copy them in
on-demand, during i915_gem_object_pin_and_relocate(). As around 20% of
the CPU overhead may be spent inside vmalloc for the relocation entries
when submitting an execbuffer [for x11perf -aa10text], the savings are
considerable and result in around a 10% throughput increase [for glyphs].
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Allow the user to override the detection of the sink's audio capabilities
from EDID. Not all sinks support the required EDID level to specify
whether they handle audio over the display connection, so allow the user
to enable it manually.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rely on monitor's audio capability to turn on audio output for HDMI.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will turn on DP audio output by checking monitor's audio
capability.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[ickle: rebase onto recent changes and rearranged for clarity]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
To help to determine if digital display port needs to enable
audio output or not. This one adds a helper to get monitor's
audio capability via EDID CEA extension block.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The time between start of the pixel clock and backlight enable is a basic
panel timing constraint. If the Panel Power On/Off registers are found
to be 0, assume we are booting without VBIOS initialization and set these
registers to something reasonable.
Change-Id: Ibed6cc10d46bf52fd92e0beb25ae3525b5eef99d
Signed-off-by: Bryan Freed <bfreed@chromium.org>
[ickle: rearranged into a separate function to distinguish its role from
simply parsing the VBIOS tables.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If userspace is submitting so many long running batches that the ring
becomes full, throttle by sleeping for a 1ms before checking for free
space. Simply yielding was causing excessive scheduler overhead whilst
making no progress.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In i2c GPIO fallback, index 6 is reserved for nothing.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI_PLL_BIOS_0 register is for Ironlake only, don't apply to
Sandybridge.
Original-patch-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since the PLL may still be on, and the training pattern may not be
correct. Fixes suspend/resume on my PCH eDP test system.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: minor merge conflict and silence the compiler]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Freeing the Hardware Status Page was writing to the HWS register in
order to disable the GPU writing to the HWS page. Unfortunately, we were
writing to the mmio register after unmapping the register space, hence
the oops.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 6939a5aca7.
Daniel Vetter supplied a set of fixes for all the module unload bugs he
could trigger on his machines, so let the fun recommence!
The enter argument as implemented by commit 413d45d362 (drm, kdb, kms:
Add an enter argument to mode_set_base_atomic() API) should be more
descriptive as to what it does vs just passing 1 and 0 around.
There is no runtime behavior change as a result of this patch.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When changing VTs non-atomically the kernel works in conjunction with
the Xserver in user space and receives the LUT information from the
Xserver via a system call. When changing modes atomically for kdb,
this information must be saved and restored without disturbing user
space as if nothing ever happened.
There is a short cut used by this patch where gamma_store is used as
the save space. If this turns out to be a problem in the future a
pre-allocated chunk of memory will be required for each crtc to save
and restore the LUT information.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit ff773714dd.
A generic solution is needed to save and retore the LUT information.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Function ttm_bo_wait_unreserved can be slightly simplified.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need the unlocked variant for the new codepath introduced to fix the
race condition in master recently.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
I see the following error message in my kernel log from time to time:
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
After investigation, it turns out that there's nothing to be afraid of
and everything works as intended. So remove the spurious log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make TV standard and DFP table revisions debug only.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These bits are used for internal communication and should
be left enabled. This may fix s/r issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should not allocate any object into unmappable vram if we
have no means to access them which on all GPU means having the
CP running and on newer GPU having the blit utility working.
This patch limit the vram allocation to visible vram until
we have acceleration up and running.
Note that it's more than unlikely that we run into any issue
related to that as when acceleration is not woring userspace
should allocate any object in vram beside front buffer which
should fit in visible vram.
V2 use real_vram_size as mc_vram_size could be bigger than
the actual amount of vram
[airlied: fixup r700_cp_stop case]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The i915 driver has quite a few module unload bugs, the known ones at
least have fixes that are targeting 2.6.37. However, in order to
maintain a stable kernel, we should prevent this known random memory
corruption following driver unload. This should have very low impact on
normal users who are unlikely to need to unload the i915 driver.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Sandybridge, the bit definition for hotplug on SDE has changed, so
update the code to new definition.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Cc: stable@kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After disabling the hotplug interrupts for VGA detection on Ironlake, be
sure to re-enable them again afterwards.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Needed on Ibex Peak and Cougar Point or the panel won't always come on.
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't use the CPU DP PLL with PCH attached eDP panels, so don't
bother to enable it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can skip most of the link training step if we use the VBT provided
values.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cache the first 4 bytes of DPCD data in the eDP case. It's unlikely to
change and can save us some trouble at link training time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We do this later (and more properly) when we enable FDI, so we don't
need to do it here.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Wait for vblank after enabling a pipe, make the error messages more
informative, and wait for the pipe to turn off when we disable it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CPU eDP needs a different reference clock than PCH eDP, which uses the
standard PCH refclk of 120MHz.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable SSC on PCH eDP if possible.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: added a posting read of PCH_DREF_CONTROL before the udelay]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to use some of these values in eDP configurations, so be sure to
fetch them and store them in the i915 private structure.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The _DSM method on the integrated graphics device can tell us which
connectors are muxable, so add support for making the call and parsing
out the connector info.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: fix compiler warnings for using uninitialized 'result' and
downgrade error message for non-switchable devices]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable the panel before adjusting eDP link params, make sure the panel
is idle after powering it on before proceeding with other activity,
delay backlight enable to avoid visible flicker.
Also avoid using VDD per hw team recommendation; it can conflict with
the builtin panel power sequencing logic and lead to panel power
sequencing failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI training needs to done and idle for PCH eDP and before we turn the
pipes on, and various eDP checks need to account for PCH attached eDP.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we set the output type of PCH attached eDP panels to
INTEL_OUTPUT_eDP this function would never return true when it should.
It's been replaced by working functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display code needs to distinguish between CPU and PCH attached eDP
panels, so add some helpers to handle that.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With the old check we'd never set lane_count or bpp to different values
on PCH attached eDP panels.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If is_edp is true, is_pch_edp will always be true. So limit the calls
to the latter function to places where the distinction actually matters.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Most of the PCH eDP checks are redundant, so document the functions in
preparation for removing most of the calls.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently, if a batch buffer refers to an object with a pending flip,
then we sleep until that pending flip is completed (unpinned and
signalled). This is so that a flip can be queued and the user can
continue rendering to the backbuffer oblivious to whether the buffer is
still pinned as the scan out. (The kernel arbitrating at the last moment
to stall the batch and wait until the buffer is unpinned and replaced as
the front buffer.)
As we only have a queue depth of 1, we can simply wait for the current
pending flip to complete and continue rendering. We can achieve this
with a single WAIT_FOR_EVENT command inserted into the ring buffer prior
to executing the batch, *without* stalling the client.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A physically mapped hardware status page is allocated at driver load
time but was never freed. Call the existing code to free this page at
driver unload time on hardware which uses this kind.
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: call before tearing down registers on KMS-only path, as pointed
out by Dave Airlie]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
since the handle references are all tied to a file_priv, and when it disappears
all the handle refs go with it.
The fbcon ones we'd only notice on unload, but the nouveau notifier one
would would happen on reboot.
nouveau: Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
nouveau: Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
i915 unload: Reported-by: Keith Packard <keithp@keithp.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-next' of ../drm-radeon-next:
drm/radeon/kms: add drm blit support for evergreen
drm/radeon: Modify radeon_pm_in_vbl to use radeon_get_crtc_scanoutpos()
drm/radeon: Add function for display scanout position query.
drm/radeon/kms: rework spread spectrum handling
drm/radeon/kms: remove new pll algo
drm/radeon/kms: remove some pll algo flags
drm/radeon/kms: prefer high post dividers in legacy pll algo
drm/radeon/kms: properly handle 40 bit MC addresses in the cursor code
drm/radeon: add properties to configure the width of the underscan borders
drm/radeon/kms/r6xx+: use new style fencing (v3)
drm/radeon/kms: enable writeback (v2)
drm/radeon/kms: clean up r6xx/r7xx blit init (v2)
* drm-kdb-next:
drm/nouveau/kms: Avoid a hang entering KDB with VT accel on.
radeon, kdb, kms: Save and restore the LUT on atomic KMS enter/exit
drm, kdb, kms: Add an enter argument to mode_set_base_atomic() API
drm/nouveau/kms: Implement KDB debug hooks for nouveau KMS.
drm/radeon/kms: Implement KDB debug hooks for radeon KMS.
[airlied - add fix for vmwgfx build]
* 'nouveau/for-airlied' of ../drm-nouveau-next: (93 commits)
drm/ttm: restructure to allow driver to plug in alternate memory manager
drm/ttm: introduce utility function to free an allocated memory node
drm/nouveau: fix thinkos in mem timing table recordlen check
drm/nouveau: parse voltage from perf 0x40 entires
drm/nouveau: don't use the default pll limits in table v2.1 on nv50+ cards
drm/nv50: Fix large 3D performance regression caused by the interchannel sync patches.
drm/nouveau: Synchronize buffer object moves in hardware.
drm/nouveau: Use semaphores to handle inter-channel sync in hardware.
drm/nouveau: Provide a means to have arbitrary work run on fence completion.
drm/nouveau: Minor refactoring/cleanup of the fence code.
drm/nouveau: Add a module option to force card POST.
drm/nv50: prevent (IB_PUT == IB_GET) for occurring unless idle
drm/nv0x-nv4x: Leave the 0x40 bit untouched when changing CRE_LCD.
drm/nv30-nv40: Fix postdivider mask when writing engine/memory PLLs.
drm/nouveau: Fix perf table parsing on BMP v5.25.
drm/nouveau: fix required mode bandwidth calculation for DP
drm/nouveau: fix typo in c2aa91afea5f7e7ae4530fabd37414a79c03328c
drm/nva3: split pm backend out from nv50
drm/nouveau: run perflvl and M table scripts on mem clock change
drm/nouveau: pass perflvl struct to clock_pre()
...
Francisco Jerez advises that pre-nv20 cards would hang if we entered
kdb with accel on and IRQs disabled, so we now disable accel before
entering kdb and re-enable it on the way back out.
Reported-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When changing VTs non-atomically the kernel works in conjunction with
the Xserver in user space and receives the LUT information from the
Xserver via a system call. When changing modes atomically for kdb,
this information must be saved and restored without disturbing user
space as if nothing ever happened.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some devices such as the radeon chips receive information from user
space which needs to be saved when executing an atomic mode set
operation, else the user space would have to be queried again for the
information.
This patch extends the mode_set_base_atomic() call to pass an argument
to indicate if this is an entry or an exit from an atomic kernel mode
set change. Individual drm drivers can properly save and restore
state accordingly.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested on nv50 and nv04 HW.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch implements blit support for bo moves using
the 3D engine. It uses the same method as r6xx/r7xx:
- store the base state in an IB
- emit variable state and vertex buffers to do the blit
This allows the hw to move bos using the 3D engine and allows
full use of vram beyond the pci aperture size.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_pm_in_vbl() didn't report in vblank status accurately. Make
it a wrapper around radeon_get_crtc_scanoutpos() which corrects for
biases, so it reports accurately.
radeon_pm_in_vbl() will only report in_vbl if all active crtc's
are currently inside vblank.
agd5f: use rdev->num_crtc rather than hardcoding the crtc count
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_get_crtc_scanoutpos() returns the current horizontal
and vertical scanout position of a crtc. It also reports if
the display scanout is currently inside the vblank area.
hpos reports current horizontal pixel scanout position.
vpos reports the current scanned out line as a value >= 0
in active scanout. If the scanout is inside vblank area, it
reports a negative value, the number of scanlines until
end of vblank aka start of active scanout, e.g., -3 ==
"At most 3 scanlines until end of vblank".
This code is derived from radeon_pm_in_vbl(), tested on
R500 and R600.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch reworks spread spectrum handling to enable it
properly on lvds and DP/eDP links. It also fixes several
bugs in the old spread spectrum code.
- Use the ss recommended reference divider if available
when calculating the pll
- Use the proper ss command tables on pre-DCE3 asics
- Avoid reading past the end of the ss info tables
- Enable ss on evergreen asics (lvds, dp, tmds)
- Enable ss on DP/eDP links
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent changes to the old algo (prefer high post div)
coupled with the range and precision limitations of using
fixed point with the new algo make the new algo less
useful. So drop the new algo. This should work as well
or better than the old new/old combinations and simplifies
the code a lot.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30218
among others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These shouldn't be needed with the post div changes
in the last patch.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows for a more exact fitting on the physical
display. The new properties default to zero which corresponds to the
previous underscan border width[height] formula:
(display_width[display_width] >> 5) + 16.
Example to set a horizontal border width of 30 and a vertikal border
height of 22:
xrandr --output HDMI-0 --set underscan on --set "underscan hborder" 30 --set "underscan vborder" 22
Signed-off-by: Marius Gröger <marius.groeger@googlemail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On r6xx+ a newer fence mechanism was implemented to replace
the old wait_until plus scratch regs setup. A single EOP event
will flush the destination caches, write a fence value, and generate
an interrupt. This is the recommended fence mechanism on r6xx+ asics.
This requires my previous writeback patch.
v2: fix typo that enabled event fence checking on all asics
rather than just r6xx+.
v3: properly enable EOP interrupts
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=29972
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When writeback is enabled, the GPU shadows writes to certain
registers into a buffer in memory. The driver can then read
the values from the shadow rather than reading back from the
register across the bus. Writeback can be disabled by setting
the no_wb module param to 1.
On r6xx/r7xx/evergreen, the following registers are shadowed:
- CP scratch registers
- CP read pointer
- IH write pointer
On r1xx-rr5xx, the following registers are shadowed:
- CP scratch registers
- CP read pointer
v2:
- Combine wb patches for r6xx-evergreen and r1xx-r5xx
- Writeback is disabled on AGP boards since it tends to be
unreliable on AGP using the gart.
- Check radeon_wb_init return values properly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Move common code to init function.
v2: make sure the bo is pinned after init as well.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Save at least one screen layout during vga save to avoid odd things
happening during restore.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This can be used by the X server to restrict mode resolutions and size of
root pixmap.
Bump minor to announce this availability.
Bump driver date.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This needs to be reviewed once we support screen objects and don't rely
on VRAM for the frame-buffer.
Also fix some integer overflow issues pointed out by Michel Daenzer.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes sure noone accesses the fifo while it's taken down using the
dirty ioctl.
Also make sure all workqueues are idled before the fifo is taken down.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed for the callback to identify the caller and take
appropriate locks if needed.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the new-style PM hooks prepare and complete. This allows us to
power up the device again after the hibernation image has been created, and
display output will thus be active until the VM is finally powered off.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Don't suspend or hibernate when there are 3D resources active since we
can't restore the device's 3D state. Instead fail with an error message.
In other cases, make sure we re-enable the fifo and unlock ttm on resume.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (266 commits)
drm/i915: Avoid circular locking from intel_fbdev_fini()
drm/i915: mark display port DPMS state as 'ON' when enabling output
drm/i915: Skip pread/pwrite if size to copy is 0.
drm/i915: avoid struct mutex output_poll mutex lock loop on unload
drm/i915: Rephrase pwrite bounds checking to avoid any potential overflow
drm/i915: Sanity check pread/pwrite
drm/i915: Use pipe state to tell when pipe is off
drm/i915: vblank status not valid while training display port
drivers/gpu/drm/i915/i915_gem.c: Add missing error handling code
drm/i915: Don't mask the return code whilst relocating.
drm/i915: If the GPU hangs twice within 5 seconds, declare it wedged.
drm/i915: Only print 'generating error event' if we actually are
drm/i915: Try to reset gen2 devices.
drm/i915: Clear fence registers on GPU reset
drm/i915: Force the domain to CPU on unbinding whilst wedged.
drm: Move the GTT accounting to i915
drm/i915: Fix refleak during eviction.
i915: Added function to initialize VBT settings
drm/i915: Remove redundant deletion of obj->gpu_write_list
drm/i915: Make get/put pages static
...
This fixes a race pointed out by Dave Airlie where we don't take a buffer
object about to be destroyed off the LRU lists properly. It also fixes a rare
case where a buffer object could be destroyed in the middle of an
accelerated eviction.
The patch also adds a utility function that can be used to prematurely
release GPU memory space usage of an object waiting to be destroyed.
For example during eviction or swapout.
The above mentioned commit didn't queue the buffer on the delayed destroy
list under some rare circumstances. It also didn't completely honor the
remove_all parameter.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=615505http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591061
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau will need this on GeForce 8 and up to account for the GPU
reordering physical VRAM for some memory types.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellström <thellstrom@vmware.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Existing core code/drivers call drm_mm_put_block on ttm_mem_reg.mm_node
directly. Future patches will modify TTM behaviour in such a way that
ttm_mem_reg.mm_node doesn't necessarily belong to drm_mm.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellström <thellstrom@vmware.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was disabled previously because of some uncertainty that +2 was
indeed the voltage. It appears it is, checked on a NVA8 and a NVA3M.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This fixes issues bug 30370 and prevents another possible divide by zero on
the original nv50 cards, by returning -ENOENT
Signed-off-by: Emil Velikov <eeydev@nottingham.ac.uk>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should fix a DMA race condition I've never seen myself, but could be
the culprit in some random hangs that have been reported.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's an unrelated PLL filtering control bit, leave it alone when
changing the CRTC-encoder binding.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This should fix eDP on certain laptops with 18-bit panels, we were rejecting
the panel's native mode due to thinking there was insufficient bandwidth
for it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On certain boards, there's BIOS scripts and memory timings that need to
be modified with the memclk. Just pass in the entire perflvl struct and
let the chipset-specific code decide what to do.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This isn't correct everywhere yet, but since we don't use the data yet
it's perfectly safe to push in, and the information we gain from logs
will help to fix the remaining issues.
v2 (Ben Skeggs <bskeggs@redhat.com>):
- fixed up formatting
- free parsed timing info on takedown
- switched timing table printout to debug loglevel
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Rephrase pwrite bounds checking to avoid any potential overflow
drm/i915: Sanity check pread/pwrite
drm/i915: Use pipe state to tell when pipe is off
drm/i915: vblank status not valid while training display port
drivers/gpu/drm/i915/i915_gem.c: Add missing error handling code
drm/i915: Fix refleak during eviction.
drm/i915: fix GMCH power reporting
lockdep spots that the fb_info->lock takes the dev->struct_mutex during
init (due to the device probing) and so we can not hold
dev->struct_mutex when unregistering the framebuffer. Simply reverse the
order of initialisation during cleanup and so do the intel_fbdev_fini()
before the intel_modeset_cleanup.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display port DPMS state is tracked internally in the display port
driver so that when a hotplug event comes along, the driver can know
whether to try retraining the link. This doesn't work well if the
driver never sets the DPMS state to ON when the output is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cancel the output polling work proc before acquiring the struct mutex
to avoid acquiring the work proc mutex with the struct mutex
held. This avoids inverting the lock order seen when the work proc
runs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Extend the error handling code with operations found in other nearby error
handling code
A simplified version of the sematic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
@r@
statement S1,S2,S3;
constant C1,C2,C3;
@@
*if (...)
{... S1 return -C1;}
...
*if (...)
{... when != S1
return -C2;}
...
*if (...)
{... S1 return -C3;}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The return from move_to_gtt_domain() may indicate a pending signal which
needs to handled as opposed to an actual error, for instance, so report
the original return value rather than forcing an EINVAL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vmwgfx: Fix fb VRAM pinning failure due to fragmentation
vmwgfx: Remove initialisation of dev::devname
vmwgfx: Enable use of the vblank system
vmwgfx: vt-switch (master drop) fixes
drm/vmwgfx: Fix breakage introduced by commit "drm: block userspace under allocating buffer and having drivers overwrite it (v2)"
drm: Hold the mutex when dropping the last GEM reference (v2)
drm/gem: handlecount isn't really a kref so don't make it one.
drm: i810/i830: fix locked ioctl variant
drm/radeon/kms: add quirk for MSI K9A2GM motherboard
drm/radeon/kms: fix potential segfault in r600_ioctl_wait_idle
drm: Prune GEM vma entries
drm/radeon/kms: fix up encoder info messages for DFP6
drm/radeon: fix PCI ID 5657 to be an RV410
The issue is that we may become stuck executing a long running shader
and continually attempt to reset the GPU. (Or maybe we tickle some bug
and need to break the vicious cycle.) So if we are detect a second hang
within 5 seconds, give up trying to programme the GPU and report it
wedged.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So far only found registers for i830, i845, i865 and one of those has no
effect on i865!
At this moment in time, attempting to reset i8xx is a little
optimistic...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When the GPU is reset, the fence registers are invalidated, so release
the objects and clear them out.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only drm/i915 does the bookkeeping that makes the information useful,
and the information maintained is driver specific, so move it out of the
core and into its single user.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
If the soon-to-be scanout buffer is partly covering the intended
VRAM region, move and pin will fail. In that case, just move it out
to system before attempting to move it in again.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The removed code causes oopses with newer drms on master drop.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is to avoid accessing uninitialized data during
drm_irq_uninstall and vblank ioctls. At the same time, enable error check from
drm_kms_init which previously appeared to ignore all errors.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We add an option not to enable fbdev, this option is off (0) by default.
Not enabling fbdev at load time makes it possible to co-operate with
vga16fb and vga text mode when VT switching.
However, if 3D resources are active when VT switching, we're currently
not able to switch over to vga, due to device limitations.
This fixes a bug where we previously lost 3D state during VT switch.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The mentioned commit breaks the vmwgfx ioctl argument sanity check.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to be fully threadsafe we need to check that the drm_gem_object
refcount is still 0 after acquiring the mutex in order to call the free
function. Otherwise, we may encounter scenarios like:
Thread A: Thread B:
drm_gem_close
unreference_unlocked
kref_put mutex_lock
... i915_gem_evict
... kref_get -> BUG
... i915_gem_unbind
... kref_put
... i915_gem_object_free
... mutex_unlock
mutex_lock
i915_gem_object_free -> BUG
i915_gem_object_unbind
kfree
mutex_unlock
Note that no driver is currently using the free_unlocked vfunc and it is
scheduled for removal, hasten that process.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30454
Reported-and-Tested-by: Magnus Kessler <Magnus.Kessler@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we hold onto a reference whilst evicting objects, we need to
be sure that we drop all the references taken -- even on the error
paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Added a function that sets the LVDS values to default settings. This
will be called by intel_init_bios before checking for the VBT (video BIOS
table). The default values are thus loaded regardless of whether a VBT
is found.
The default settings in each parse function have been moved to the new
function. This consolidates all the default settings into one place.
The default dither bit value has been changed from 0 to 1. We can
assume that display devices will want dithering enabled.
Signed-off-by: Simon Que <sque@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
[ickle: fixup for -next]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At that point as the object is no longer in any GPU write domain it must
not be on the list, so the list_del() is redundant.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i810 and i830 device drivers may replace their file operations
on an open file descriptor. My previous patch to move the BKL
out of the common DRM code into these drivers only caught the
default file operations, not the ones that actually end up being
used.
Found while trying to come up with a way to kill the BKL for
good in these drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just reschedule the retire requests again if the device is currently
busy. The request list will be pruned along other paths so will never
grow unbounded and so we can afford to miss the occasional pruning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This check only appears to succeed when using GMBUS, so we need to skip
it if we have fallen back to using GPIO bit banging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There are several reported instances of GMBUS failing to successfully
read the EDID, so revert back to bit banging until the issue is
resolved.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30371
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Besides a couple of bugs when writing more than a single byte along the
GMBUS, SDVO was completely failing whilst trying to use GMBUS, so use
bit banging instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With multiple rings generating requests independently, the outstanding
requests must also be track independently.
Reported-by: Wang Jinjin <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Board has no digital connectors
Reported-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hook the GEM vm open/close ops into the generic drm vm open/close so
that the private vma entries are created and destroy appropriately.
Fixes the leak of the drm_vma_entries during the lifetime of the filp.
Reported-by: Matt Mackall <mpm@selenic.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IPS driver needs to know the current power consumption of the GMCH
in order to make decisions about when to increase or decrease the CPU
and/or GPU power envelope. So fix up the divisions to save the results
so the numbers are actually correct (contrary to some earlier comments
and code, these functions do not modify the first argument and use it
for the result).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
encoder info was not printed properly on boards using the
DFP6 id.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduced by 48b956c5, I had thought I had already fixed this. Oh well.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Daniel Vetter pointed out that in this case is would be clearer and
cleaner to use a spinlock instead of a mutex to protect the per-file
request list manipulation. Make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I've accidently killed a little bit too much in
commit 1da3f87ebb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Aug 23 22:53:24 2010 +0200
drm: kill kernel_context_switch callbacks
Note to self: Next time also test with AIGLX disabled.
Reported-and-Tested-by: Andy Furniss <lists@andyfurniss.entadsl.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30374
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's the same code, essentially, so kill all copies safe one unified
version.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
All functions are extremely similar, so fold them into one generic
implementation.
This function isn't used anyway, because there's not yet a bsd ring
error state dumper.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Two macros that use a base address for HWS_PGA were missing, add them.
Also switch the remaining users of *_ACTHD to the ring-base one.
Kill the other ring-specific macros because they're now unused.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[ickle: And silence checkpatch whilst in the vicinity]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This was mixed up in the following patch:
commit a6c45cf013
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Sep 17 00:32:17 2010 +0100
drm/i915: INTEL_INFO->gen supercedes i8xx, i9xx, i965g
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Everything is now handled in intel-gtt.h so these defines
are only confusing.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Owain Ainsworth reported an issue between the interaction of the
hangcheck and userspace immediately (and permanently) falling back to
s/w rasterisation. In order to break the mutex and begin resetting the
GPU, we must abort the current operation (usually within the wait) and
climb sufficiently far back up the call chain to drop the mutex. In his
implementation, Owain has a loop within the ioctl handler to detect the
hang and then sleep until the error handler has run. I've chosen to
return to userspace and report an EAGAIN which should trigger the
userspace ioctl handler to repeat the call (simply because it felt less
invasive...). Before hitting a wedged GPU, we then wait upon completion
of the error handler.
Reported-by: Owain G. Ainsworth <zerooa@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid cause latencies in other clients by not taking the global struct
mutex and moving the per-client request manipulation a local per-client
mutex. For example, this allows a compositor to schedule a page-flip
(through X) whilst an OpenGL application is monopolising the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch fixes the black screen bug on Dell e6510, by
adding two delays to give the eDP panel time to turn on before we
continue with the next write.
300ms is rather arbitray and a rather long sleep, we need to find a way
of refining this value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29278
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
First step, lets have a look at the values for troublesome panels and
see if they may be used to improve our link training.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to drain the pending flips prior to disabling the pipe during
modeset, and these need to be done in an uninterruptible fashion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we presume space is signed when computing and looking for wrap along,
make it so.
Reported-by: Owain G. Ainsworth <zerooa@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Just in case someone, somewhere, does something difficult. This also
removes one path that was different between fermi and non-fermi.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francesco Marella <fmarl@paranoici.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Used on nv17-nv28, they contain memory clocks and timings, only one of
the table entries can actually be used, depending on the RAMCFG
straps, and it's usually higher than the frequency programmed on boot
by the BIOS.
The memory timings listed in table version 0x1x are used to init the
0x12xx range but they aren't required for reclocking to work.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Build breakage:
drivers/built-in.o: In function `nouveau_acpi_edid':
(.text+0x13404e): undefined reference to `acpi_video_get_edid'
make: *** [.tmp_vmlinux1] Error 1
Introduced by:
a6ed76d7ff is the first bad commit
commit a6ed76d7ff
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon Jul 12 15:33:07 2010 +1000
drm/nouveau: support fetching LVDS EDID from ACPI
Based on a patch from Matthew Garrett.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
It doesn't seem to revert cleanly, but the problem lies in these
two config entries:
CONFIG_ACPI=y
CONFIG_ACPI_VIDEO=m
Adding a select for ACPI_VIDEO appears to be the best solution, and
is comparable to what is done in DRM_I915. Builds, boots, and appears to
work correctly.
Signed-off-by: Philip J. Turmel <philip@turmel.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently just hooked up to the already-existing nouveau_hw, which should
handle all relevant chipsets as well as we currently can.
This will likely be eventually split out and improved into chipset specific
code at a later point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will make nouveau_pm attempt to report the card's current performance
level both during bootup, and through sysfs.
This is a very initial implementation, and can be improved a *lot*
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This replaces all the pll_types definitions for ones that match the types
used in the tables in recent VBIOS versions.
get_pll_limits() will now accept either type or register value as input
across all limits table versions, and will store the actual register ID
that a PLL type refers to in the returned structure.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The rest of the connector code assumes we can kfree() the EDID pointer.
This causes things to blow up with the ACPI EDID pointer we get
passed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The most important part of this change is that we now instruct PFIFO to
drop all pending fetches, rather than attempting to skip a single dword
and hope that things would magically sort themselves out - they usually
don't, and we end up with PFIFO being completely hung.
This commit also adds somewhat more useful logging when these exceptions
occur.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More Apple brain damage, it fixes the modesetting failure on an eMac
G4 (fdo bug 29810).
Reported-by: Zoltan Varnagy <doi@freemail.hu>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Instead of emptying the caches to avoid a race with the PFIFO puller,
go straight ahead and try to recover from it when it happens. Also,
kill pfifo->cache_flush and tile->lock, we don't need them anymore.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes sure that RAMHT is cleared correctly on start up.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
FW seems to be broken on nv18, it causes random lockups and breaks
suspend/resume even with the blob.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This doesn't actually happen now, but there's a test case for an earlier
kernel where a GPU error is signalled on one of nv50's fake channels, and
the ramht lookup by the IRQ handler triggered an oops.
This adds a check for RAMHT's existance on a channel before looking up
an object handle.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Will be used at a later point when we plug in an alternative VRAM memory
manager for GeForce 8+ boards.
Based on pscnv code to do the same.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
They don't seem to do anything useful, and we really want to program
CRE_LCD if we aren't lucky enough to find the right CRTC binding
already set.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some boards the residual current DAC outputs can draw when they're
disconnected can be high enough to give a false load detection
positive (I've only seen it in the S-video luma output of some cards,
but just to be sure). The output line capacitance is limited and
sampling twice should fix it reliably.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Hopefully this one will be better able to cope with moving tiled buffers
around without getting them all scrambled as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nv2x CRTC FIFOs are as large as in nv3x (4kB it seems), and the FIFO
control registers have the same layout: we can make them share the
same implementation.
Previously we were using the nv1x code, but the calculated FIFO
watermarks are usually too low for nv2x and they cause horrible
scanout artifacts. They've gone unnoticed until now because we've been
leaving one of the bandwidth regs uninitialized (CRE 47, which
contains the most significant bits of FFLWM), so everything seemed to
work fine except in some cases after a cold boot, depending on the
memory bandwidth and pixel clocks used.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some nv4x cards (specifically, the ones that use an internal
PCIE->AGP bridge) the AGP controller state isn't preserved after a
suspend/resume cycle, and the AGP control registers have moved from
0x18xx to 0x100xx, so the FW check in nouveau_mem_reset_agp() doesn't
quite work. Check "dev->agp->mode" instead.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Correct function being needlessly visible outside compilation unit
when the only users are internal.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix string interpreted as trigraph and typo.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Correct function storage class, and correct assignment type.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Correct allocation flags type and function prototype for ANSI C compliance.
[airlied: whitespace fixed]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the event that the external chipset doesn't implement the
GET_SUPPORTED_ENHANCEMENTS commands, gracefully treat it as having no
enhancments rather than bailing.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We weren't unlinking the freed connector from the drm lists, and so
hit some use-after-free if we failed to initialise the connector.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to wait for the PLLs to settle prior to detecting the state
changes. The BIOS writers guide suggests waiting for the next vblank.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is already performed with the pipelined flush, so by the time we
schedule the flush in the page-flip, the ring is NULL and we OOPs
instead.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A minor typo caused a single fence register to be incorrectly
programmed, resulting in occassional tiling corruption.
Reported-and-tested-by: Hans de Bruin <bruinjm@xs4all.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18962
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The BIOS writer's guide suggests that a VGA connection will ACK a write
to address 0xA0 and that this should be used before doing legacy
load-detection. Considering the extreme cost of load-detection,
performing an extra DDC seems a risk worth taking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously when converting the GMBUS pin to the GPIO reg, we would
offset the pin by one and then use the look-up table. Now that we first
try to use the GMBUS pin, we no longer need the offset and can use the
value from the VBIOS directly.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It makes sense for a BO to move after a process has requested
exclusive RW access on it (e.g. because the BO used to be located in
unmappable VRAM and we intercepted the CPU access from the fault
handler).
If we let the ghost object inherit cpu_writers from the original
object, ttm_bo_release_list() will raise a kernel BUG when the ghost
object is destroyed. This can be reproduced with the nouveau driver on
nv5x.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we do not wait for the panel to turn off when we need to adjust the
panel-fitting registers we also need to unlock the PLLs as with the
non-pfit update path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to handle disable_functions() where the framebuffer is
decoupled from the crtc we need to unpin the fb in order to prevent a
leak.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Suspending (especially hibernating) may take a finite amount of time,
during which a hotplug event may trigger and we will attempt to handle
it with inconsistent state. Disable hotplug polling around suspend and
resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30070
Reported-by: Rui Tiago Matos <tiagomatos@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Consolidate everything in intel-gtt.c and also kill the export
of intel_max_stolen.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Keep a list of pinned objects and display it via debugfs. Now all
objects that exist in the GTT are always tracked on one of the
active, flushing, inactive or pinned lists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we have queued a page flip on the current fb and then request a mode
change, wait until the page flip completes before performing the new
request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Track if the gpu requires the fence for the execution of a batch buffer
and so only wait upon the retirement of the object's last rendering
seqno if the fence is in use by the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Always PAGE_SIZE and only complicates the code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Documentation explicitly mentions that the ring registers are
designed to have the same offsets relative to a base registers.
Use this to fight the code beaurocratic in intel_ringbuffer.c.
No code changes in this patch, just the new definitions.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This looks like a copy-paste remnant from the i810. All the regs
that are actually used are already defined somewhere else in i915_reg.h!
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ring buffer is used for video decoding/encoding on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As noted by Zhenyu, we can now simply replace the existing advance hook
by calling the new set_tail function pointer directly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is prepared for video codec ring buffer on Sandybridge. It is
needed to read/write more than one register to move the tail pointer of
the video codec ring on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Introduce intel_init_render_ring_buffer(), intel_init_bsd_ring_buffer
for ring initialization.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously we only tidied up the active bo lists for chipsets were we
would attempt to reset the GPU. However, this action is necessary for
the system to continue and reclaim the dead bo for all chipsets.
Pointed out, in passing, by Owain Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Clear the GPU read domain for the inactive objects on a reset so that
they are correctly invalidated on reuse.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Owain Ainsworth noticed that the reset code failed to clear the flushing
list leaving the driver in an inconsistent state following a hung GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When flushing the GPU domains,we emit a flush on *both* rings, even
though they share a unified cache. Only emit the flush on the currently
active ring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Change the semantics to retire any buffer older than the current seqno
rather than repeatedly calling calling the function to retire the
buffer at the head of the list matching the request seqno.
Whilst this should have no semantic impact on the implementation, Daniel
was wondering if there was a bug where we might miss a retirement and so
end up with a continually growing active list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On more recent chipsets, restoring the display is not as simple as
writing a few registers, so force a full modeset of the current
configuration in order to retrain the display link.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ironlake's graphics reset register has to be accessed via the MCHBAR,
rather than via PCI config space, which requires some refactoring.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The graphics domains are listed as GRDOM in the documentation, and the
GDRST PCI config register (0xc0) is only valid on I965 and GM45. Newer
chips (like Sandy Bridge) have a different GDRST.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously, it was only being set if passed GDRST_FULL - but the only
caller passed GDRST_RENDER. So the hardware never actually reset.
The comments also did not match the code.
Instead, just set the reset bit regardless of what flags were passed.
The GPU now resets correctly on my GM45.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We assume that the panel is permenantly connected and that the EDID data
is consistent from boot, so simply cache the whole EDID for the panel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
During heavy aperture thrashing we may be forced to wait upon several active
objects during eviction. The active list may be the last reference to
these objects and so the action of waiting upon one of them may cause
another to be freed (and itself unbound). To prevent the object
disappearing underneath us, we need to acquire and hold a reference
whilst unbinding.
This should fix the reported page refcount OOPS:
kernel BUG at drivers/gpu/drm/i915/i915_gem.c:1444!
...
RIP: 0010:[<ffffffffa0093026>] [<ffffffffa0093026>] i915_gem_object_put_pages+0x25/0xf5 [i915]
Call Trace:
[<ffffffffa009481d>] i915_gem_object_unbind+0xc5/0x1a7 [i915]
[<ffffffffa0098ab2>] i915_gem_evict_something+0x3bd/0x409 [i915]
[<ffffffffa0027923>] ? drm_gem_object_lookup+0x27/0x57 [drm]
[<ffffffffa0093bc3>] i915_gem_object_bind_to_gtt+0x1d3/0x279 [i915]
[<ffffffffa0095b30>] i915_gem_object_pin+0xa3/0x146 [i915]
[<ffffffffa0027948>] ? drm_gem_object_lookup+0x4c/0x57 [drm]
[<ffffffffa00961bc>] i915_gem_do_execbuffer+0x50d/0xe32 [i915]
Reported-by: Shawn Starr <shawn.starr@rogers.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18902
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a second revision of B43 (a desktop gen4 part) floating around,
functionally equivalent to the original B43, so simply add the new
PCI-IDs.
Bugzilla: https://bugs.freedesktop.org/show_bugs.cgi?id=30221
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
With 5 places to update when adding handling for fence registers, it is
easy to overlook one or two. Correct that oversight, but fence
management should be improved before a new set of registers is added.
Bugzilla: https://bugs.freedesktop.org/show_bug?id=30199
Original patch by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
These are not fatal errors, so do not alarm the user by filling the
logs with *** ERROR ***. Especially as we know that g4x CRT detection
is a little sticky.
On the one hand the errors are valid since they are warning us of a
stall -- we poll the register whilst holding the mode lock so not even
the mouse will update. On the other hand, those stalls were already present
yet nobody complained.
Reported-by: Andi Kleen <andi@firstfloor.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18332
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The drm device drivers currently allow seeking on the
character device but never care about the actual
file position.
When we change the default llseek operation to be
no_llseek, calling llseek on a drm device would
return an error condition, which is an API change.
Explicitly setting noop_llseek lets us keep the
current API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Later initialisation of the encoder often requires that
drm_encoder_init() has already been called, for instance, initialiasing
the DDC buses.
Yet another recent regression, as 819f3fb7 depended upon these fixes
which I missed when cherry-picking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
One problem with devices that share the DDC bus between the VGA and
DVI-I connectors is that with two devices attached we cannot know if
there is truly a monitor attached to the DVI connector. In this case, it
is preferrrable to mark the status as unknown, so that the user can
supply the known set of modes and continue to use the output.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only need to use the analog encoder for rare devices which share the
DDC between the DVI-I and VGA connectors, so only create as needed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The texture base address registers are in units of 256 bytes.
The original CS checker treated these offsets as bytes, so the
original check was wrong. I fixed the units in a patch during
the 2.6.36 cycle, but this ended up breaking some existing
userspace (probably due to a bug in either userspace texture allocation
or the drm texture mipmap checker). So for now, until we come
up with a better fix, just warn if the mipmap size it too large.
This will keep existing userspace working and it should be just
as safe as before when we were checking the wrong units. These
are GPU MC addresses, so if they fall outside of the VRAM or
GART apertures, they end up at the GPU default page, so this should
be safe from a security perspective.
v2: Just disable the warning. It just spams the log and there's
nothing the user can do about it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we currently may need to acquire a fence register during a modeset,
we need to be able to do so in an uninterruptible manner. So expose that
parameter to the callers of the fence management code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ensures that we do wait upon the flushes to complete if necessary
and avoid the visual tears, whilst enabling pipelined page-flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not 100% sure this is due to BKL removal, its most likely a combination
of that + userspace timing changes in udev/plymouth. The drm adds the sysfs
device before the driver has completed internal loading, this causes udev
to make the node and plymouth to open it before we've completed loading.
The proper solution is to delay the sysfs manipulation until later in loading
however this causes knock on issues with sysfs connector nodes, so we can use
the global mutex to serialise loading and userspace opens.
Reported-by: Toni Spets (hifi on #radeon)
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I pulled the wrong version of the patch from Daniel Vetter which was
missing the read barriers -- and the one that was causing all the trouble
was from i915_gem_object_put_fence_reg(), leading to GPU hangs on gen3.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By reducing the hangcheck frequency we check less often, conserving
resources, and still detect a lock up quickly. On a fast machine with a
slow GPU (like a Core2 paired with a 945G) it is easy for the hangcheck to
misfire as we check too fast.
Also once hung and if we fail to completely reset the chip, we have a
nasty habit of proclaming a hang many times a second and generating a
strobe-like display.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix a regression in the previous regression fix...
In order to turn off the pipes entirely upon the first modeset, we
pretend that BIOS (or earlier module incarnation) left them active.
The first task performed by setup_initial_configuration() is to disable
all pipes and so to avoid skipping that step and so to ensure a known
configuration we need to mark all the crtcs as active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When separating out the prepare/commit into its own separate functions
we overlooked that the intel_crtc->dpms_mode was being used elsewhere to
check on the actual status of the pipe.
Track that bit of logic separately from the actual dpms mode, so there
is no confusion should we be able to handle multiple dpms modes, nor
any semantic conflict between prepare/commit and dpms.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This closes a couple of corner cases where we introduced and forgot
about a couple of routines that need to be called when disabling the
crtc and then re-enabling it. The code needs to be moved again so that
the common bits are shared across generations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This commit fixes bogus CS rejection if it contains a sequence
of the following operations:
- Set the color buffer 0. track->cb[i].robj becomes non-NULL.
- Render.
- Set a larger zbuffer than the previously-set color buffer.
- Set a larger scissor area as well.
- Set the color channel mask to 0 to do depth-only rendering.
- Render. --> rejected, because track->cb[i].robj remained non-NULL,
therefore the conditional checking for the color channel mask and
friends is not performed, and the larger scissor area causes
the rejection.
This fixes bugs:
- https://bugs.freedesktop.org/show_bug.cgi?id=29762
- https://bugs.freedesktop.org/show_bug.cgi?id=28869
And maybe some others which seem to look the same.
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One subtest of mesa/demos/gltestperf takes 9 seconds to complete,
so to prevent an unnecessary gpu reset followed by a hardlock, I am
increasing the interval to 10 seconds after which a GPU is considered
in a locked-up state. This is on RV530. However, with a little slower GPU,
we would surpass the interval easily, so this is not a good fix
for gltestperf.
Nevertheless, this commit also fixes hardlocks in the applications which
render at speed of less than 1 frame per second, where the whole frame
consists of only one command stream. The game Tiny & Big is an example.
This bar is now lowered to 0.1 fps.
Now the question comes down to whether we should (often unsuccessfully)
reset the GPU at all? Once we have stable enough drivers, we won't have to.
Has the time come already?
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes rendering errors on some evergreen boards.
Hardcoding the backend map is not an optimal solution, but
a better fix is being worked on.
Similar to the fix for rv740
(6271901d82).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29986
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise when disabling the output we switch to the new fb (which is
likely NULL) and skip the call to mode_set -- leaking driver private
state on the old_fb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
caused by d65d65b175
need to update the radeon crtc priv native mode before using it.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30049
v2: integrate v/h copy paste typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I broke out my trusty i845 and found a new boot failure, which upon
inspection turned out to be a recursion within:
drm_helper_probe_single_connector_modes() -> drm_helper_hpd_irq_event()
-> intel_crt_detect() -> drm_helper_probe_single_connector_modes()
Calling drm_kms_helper_poll_enable() instead performs the desired
re-initialisation of the polling should the user have toggled the
parameter, without the recursive side-effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 77d07fd9d7 introduced a regression
where by not waiting for the panel to be turned off, left the panel and
PLL registers locked across the modeset. Thus the panel remaining blank.
As pointed out by Daniel Vetter, when testing LVDS it helps to open the
laptop and look at the actual panel you are purporting to test.
A second issue with the patch was that in order to modify the panel
fitter before gen5, the pipe and the panel must have be completely
powered down. So we wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The documentation says that an SDVO command takes a maximum of 15us to be
processed by the device, and that it is sufficient to read the status byte
3 times (whilst the command is still in the PENDING state) for the driver
to be confident that sufficient time has elapsed.
We err on the safe side and try 5 times before giving up.
The only question that remains: was the old behaviour derived by
experiments with real hardware?
A look into the murky history of UMS, implies that the behaviour was
accidental and the current retry mechanism was solely designed to catch
the status byte indicating PENDING with no reference to hardware
behaviour. (commit ac9181c014638dbeb334b40b4029d0ccb2b7a0fc in
xf86-video-intel)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid a potentially long busy-wait if we not in the process of
atomically switching to the kdb console.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We just assume that it will happen in a timely manner. A variant of this
patch was first written and tested by Arjan van de Van.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Remove our redundant udelay() as the timings are already handled by the
i2c-algo-bit controller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The purpose is to make the code much easier to read and therefore reduce
the possibility for bugs.
A side effect is that it also makes it much easier for the compiler,
reducing the object size by 4k -- from just a few functions!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Refactor the common code into seperate functions and use the MIN(large,
small) buffer calculation for self-refresh watermarks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to track different state on each generation in order to detect
when we need to refresh the FBC registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Thermal reporting may not be enabled by default on some machines, so
enable the appropriate bits to allow IPS to get the data it needs from
the CPU thermal device.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: don't enable self-refresh on Ironlake
drm/i915: Double check that the wait_request is not pending before warning
Revert "drm/i915: Warn if we run out of FIFO space for a mode"
Revert "drm/i915: Allow LVDS on pipe A on gen4+"
Revert "drm/i915: Enable RC6 on Ironlake."
TU size is only part of the M1 and M2 regs, not the N regs. This keeps
us from overwriting a reserved field.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Easier to read, and will pair up with a disable function.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
eDP panels require these to be set up prior to panel power sequencing,
or they'll fail to power on due to an "asset not ready" check. And of
course, eDP panels attached to anything other than DP_A need them
enabled regardless, since they'll be driven from the CPU through FDI out
to the PCH.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will allow us to optimize our prepare/commit paths a bit better.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: minor tweak to handle the cursor across pipe resizing]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This was just a workaround for some broken Ironlake CRTC code.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So we can use it for CRTC prepare/commit.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This way we can also use it in CRTC prepare/commit. Also makes it
easier to split out FDI and other code.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
create_singlethreaded_workqueue() is being phased out for a new
concurrency managed task infrastructure.
Adapt our workqueue constructor to explicitly create a domain that only
allows the execution of a single task at any time. All the tasks are
expected to require the dev->struct_mutex, so would block concurrency of
other tasks if we allow more than a single i915 task to be run at once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't know how to enable it safely, especially as outputs turn on and
off. When disabling LP1 we also need to make sure LP2 and 3 are already
disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29173
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29082
Reported-by: Chris Lord <chris@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently we have a exact mapping of a connector onto an encoder for its
whole lifetime. Make this an explicit property of the structure and so
simplify the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Why iterate all the crtcs to find the pipe, when we already know which
crtc is attached to which pipe?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[Patch is slightly larger than is strictly necessary to fixup
surrounding checkpatch.pl errors.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.
Fixes regression with e78d73b16b.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Otherwise we may not be able to train the DP link.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When turning on or off the VDD AUX bit, we need to give the panel time
to start or stop or AUX transactions may fail.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Mode set sequence outlines when the AUX VDD bit should be set and
cleared, and it's separate from the panel power sequence.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Mode set sequence requires that we start training, then enable the
panel, then complete training. So split the DP training function into
two parts; the first enables the DP port and sets training pattern 1 and
the second completes the training.
As part of this, remove some redundant function args from the various DP
handling functions and use the intel_dp fields everywhere we can.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: removed first ironlake_edp_backlight_on() on advice of jbarnes]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Mode setting sequence specifies that we use VDD AUX for configuration
and detection, and early in the mode set sequence. Only later (after
DP_A has started training) should we actually enable panel power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: checkpatch.pl complaining about whitespace]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix the test so we don't try to use the 450MHz refclk on PCH attached
eDP.
References:
https://bugs.freedesktop.org/show_bug.cgi?id=29141
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
snprintf() returns the number of bytes which would have been used if
there was enough space. It can be larger than the size of the buffer.
Obviously in this case the buffer is large enough but everyone just
copy and pastes this code so it's better to limit it and set a good
example.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the detection from intel-gtt.ko instead. Hooray!
Also move the stolen mem allocator to the other gtt stuff in dev_prv->mem.
v2: Chris Wilson noted that my error handling was crap. Fix it. He also
said that this fixes a problem on his i845. Indeed, i915_probe_agp
misses a special case for i830/i845 stolen mem detection.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=25476
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a few definitions to it that are already shared and that will
be shared in the future (like the number of stolen entries).
No functional changes in here.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It seems to be possible to program a new mode without disabling the panel
if the panel fitter setup doesn't change. Add support for that.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We really need a macro to test whether a given connector has a panel
attached rather than sprinkling HAS_PCH_SPLIT/IS_eDP/has_edp_encoder
etc all over. In the meantime, fix the bug...
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: tidy up the duplicity in the conditionals]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Make them match the others and add BPP definitions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The GPU records whether it is currently waiting for a completion of a
WAIT_FOR_EVENT in the RB_WAIT bit in the ringbuffer control registers.
On third generation chipsets and later, a write of 1 to this bit breaks
the hang and returns the GPU to arbitration, i.e. the GPU should
continue executing the reminder of the batchbuffer and return to normal
operations.
By adding this to hangcheck we can avoid a full GPU reset under these
conditions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we disable the pipe and the GPU is currently waiting on a scanline
WAIT_FOR_EVENT, the GPU will hang. Fortunately, there is a magic bit
which we can write on i915+ to break this wait after disabling the
pipe.
References:
Bug 29252 - [Arrandale] Hung WAIT_FOR_EVENT when running rss-glx-skyrocket
https://bugs.freedesktop.org/show_bug.cgi?id=29252
Bug 28964 - [i965gm] GPU infinite MI_WAIT_FOR_EVENT while watching video in Totem
https://bugs.freedesktop.org/show_bug.cgi?id=28964
and many others.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Hopefully this is a contributing factor to the spurious TV detection
repoted by Ivan Bulatovic and others.
References:
Bug 16871 - "TV1 connected" with no tv
https://bugzilla.kernel.org/show_bug.cgi?id=16871
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Ivan Bulatovic <combuster@gmx.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
There were two instances of code to control the panel backlight and
neither handled the complete set of device variations.
Fixes:
Bug 29716 - [GM965] Regression: Backlight resets to minimum when changing resolution
https://bugs.freedesktop.org/show_bug.cgi?id=29716
And a bug on one of my PineView boxes which overflowed the backlight
value.
Incorporates part of a similar patch by Matthew Garrett that exposes a
native Intel backlight controller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We do it whilst configuring dev->mode_config, so remove the out-of-place
earlier initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This spinlock only served debugging purposes in a time when we could not
be sure of the mutex ever being released upon a GPU hang. As we now
should be able rely on hangcheck to do the job for us (and that error
reporting should not itself require the struct mutex) we can kill the
incomplete attempt at protection.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We have no idea why we request a SyncFlush via INSTPM at that point in
time -- we certainly never check for its completion...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Alexander reported that the compilation of intel_overlay.c was failing
due to an inclusion that was only valid with CONFIG_DEBUG_FS. As the
whole error reporting is only useful with debugfs enabled, remove all
the redundant error state collection code when compiling without
CONFIG_DEBUG_FS.
Reported-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Slightly easier to follow than the state machine and now possible as the
control structure is opaque and hw_wedged is no longer interferred with.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During DPMS we currently do not want the overlay code to be
interruptible, so pass that information down and only take the
uninterrruptible paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On i830, there exists a bug where an overlay on pipe B requires the mode
clock on pipe A in order to activate. So workaround this by activating
pipe A when trying to enable the overlay on pipe B.
References:
[Bug 29007] GPU hang on video playback with overlay
https://bugs.freedesktop.org/show_bug.cgi?id=29007
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By allocating the request prior to writing to the ringbuffer, we can
abort the operation without leaving the GPU in an inconsistent state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inline the call to wait_flip() and simplify the resulting code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can program the h/w to first wait on the flip and then switch off
without relying on s/w intervention. This removes the need for a double
step switch off, bringing much rejoicing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scoping of the validity of the mapping is thus clarified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only time where an atomic mapping is required is during
error-capture and there we cannot use the default slot, but need to
specifically use one of the IRQ slots. So separate out the two
conditions and use the atomic mapping only when appropriate.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just makes sure that writes are not being aliased by the CPU cache and
do make it out to main memory.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=24977
Cc: stable@kernel.org
... take advantage of the new implicit request issuing of
i915_wait_request.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
One caller (for the pageflip support) wants a purely pipelined flush.
Distinguish this case by a new parameter. This will also be useful
later on for pipelined fencing.
v2: Simplify the code by depending upon the implicit request emitting
of i915_wait_request.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[ickle: And drop the non-interruptible support in the process.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By moving one i915_add_request we can solely depend on the new
auto-seqno-numbering behaviour.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
i915_gem_object_move_to_active can handle zero seqno for us now.
And not emitting a request is not fatal here - we'll try to emit
a new one if we have to wait for some rendering to complete.
In case this assumption ever gets accidentally broken, there's already
a BUG_ON to catch it in i915_do_wait_request.
So just silently ignore ENOMEM here instead of screwing up the whole
drm.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... instead of threading flush_domains through the execbuf code to
i915_add_request.
With this change 2 small cleanups are possible (likewise the majority
of the patch):
- The flush_domains parameter of i915_add_request is always 0. Drop it
and the corresponding logic.
- Ditto for the seqno param of i915_gem_process_flushing_list.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously I thought that one interrupt per batchbuffer should be
enough. Now tedious benchmarking showed this to be wrong.
Therefore track whether any commands have been isssued with a future
seqno (like pipelined fencing changes or flushes). If this is the case
emit a request before issueing the batchbuffer.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Now that we can move objects to the active list without already having
emitted a request, move the flushing list handling into i915_gem_flush.
This makes more sense and allows to drop a few i915_add_request calls
that are not strictly necessary.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sometimes (like when flushing in preparation of batchbuffer execution)
we know that we'll emit a request but haven't yet done so. Allow this
case by simply taking the next seqno by default. Ensure that a request
is eventually emitted before waiting for an request by issuing it
in i915_wait_request iff this is not yet done.
Also replace one open-coded version of i915_gem_object_wait_rendering,
to prevent future code-diversion.
Chris Wilson asked me to explain and clarify what this patch does and why.
Here it goes:
Old way of moving objects onto the active list and associating them with a
reques:
1. i915_add_request + store the returned seqno somewhere
2. i915_gem_object_move_to_active (with the stored seqno as parameter)
For the current users, this is all fine. But I'd like to associate objects
(and fence regs) with the batchbuffer request deep down in the execbuf
call-chain. I thought about three ways of implementing this.
a) Don't care, just emit request when we need a new seqno. When heavily
pipelining fence reg changes, this would have caused tons of superflous
request (and corresponding irqs).
b) Thread all changed fences, objects, whatever through the execbuf-maze,
so that when we emit a request, we can store the new seqno at all the right
places.
c) Kill that seqno-threading-around business by simply storing the next
seqno, i.e. allow 2. to be done before 1. in the above sequence.
I've decided to implement c) (in this patch). The following patches are
just fall-out that resulted from this small conceptual change.
* We can handle the flushing list processing where we actually emit a flush
(i915_gem_flush and i915_retire_commands) instead of in i915_add_request.
The code makes IMHO more sense this way (and i915_add_request looses the
flush_domains parameter, obviously).
* We can avoid emitting unnecessary requests. IMHO there's no point in
emitting more than one request per batchbuffer (with or without an
corresponding irq).
* By enforcing 2. before 1. ordering in the above sequence the seqno
argument of i915_gem_object_move_to_active is redundant and can be
dropped.
v2: Now i915_wait_request issues request if it is not yet emitted.
Also introduce i915_gem_next_request_seqno(dev) just in case we ever
need to do some prep work before using a new seqno.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[ickle: Keep i915_gem_object_set_to_display_plane() uninterruptible.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Useful for capturing register read/write traces to send to the hw guys.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of sleeping for an arbitrary length of time (the documentation
fails to specify how long to wait for) wait until the load detection has
changed state (or at most the 20ms as before).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With the extra intel_wait_for_vblank added in commit
9d0498a2bf periodic stalls were being
triggered (which were detected by i915_hangcheck_elapsed). Partially
revert this change for now.
Signed-off-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix a minor confusion between intel_page_flip_finish(pipe) and
intel_page_flip_finish_plane(plane) -- should have no effect as
currently we map pipe 0 to plane 0 (and pipe 1 to plane 1).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
My Samsung N210 has a VBT with DEVICE_TYPE_INT_LFP with a zero
addin-offset. With the check in place, the panel was declared absent.
v2: Only trust BIOS writers that have graduated to writing OpRegions.
(We are all doomed.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Cc: Adam Jackson <ajax@redhat.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
It is recommended that we use the Video BIOS tables that were copied
into the OpRegion during POST when initialising the driver. This saves
us from having to furtle around inside the ROM ourselves and possibly
allows the vBIOS to adjust the tables prior to initialisation.
On some systems, such as the Samsung N210, there is no accessible VBIOS
and the only means of finding the VBT is through the OpRegion.
v2: Rearrange the code so that ASLE is enabled along with ACPI
v3: Enable OpRegion parsing even without ACPI
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
It's part of the generic Intel driver infrastructure so rename it in
prepreparation for using it for VBT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we don't flush the write then we can not be sure that the border
colour will have taken effect by the time we try to read it back.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
wait_for() uses msleep() to yield the cpu whilst spinning waiting for a
register to change. kdb asserts that mode changes are atomic and so
prohibits msleep. The alternative would be to use mdelay or to simply
probe the register more often instead of busy waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Jesse's feedback from using the wait_for() macro was that the msleep
argument was that it was superfluous and made the macro more difficult
to use and to read. As the actually amount of time to sleep is not
critical, the crucial part is to sleep and let the processor schedule
something else whilst we wait for the event, replace the argument with a
hardcoded value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
ums-gem code correctly cancels the retire work (at lastclose time),
kms does not do so. Fix this by canceling the work right after ideling
the gpu.
While staring at the code I noticed that the work function is not
static. Fix this, too.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When the module unloads, all users should be gone, hence all bo references
held by userspace, too. This should already result in an idle ringbuffer.
Still, be paranoid and idle gem before starting the unload dance.
Also kill the call to i915_gem_lastclose under an if (kms), it's a noop
for kms.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Kill any outstanding unpin_work when destroying the corresponding
crtc. Then flush the workqueue before the gem teardown, in case
any unpin work is still outstanding.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
idle_work wasn't cleaned up at all. It takes &dev->struct_mutex, but
accesss the mode_config crtc list (without any other locking!). Hence
this work needs to be canceled before calling drm_mode_config_cleanup.
As evidenced by the kernel's object debuggin code, the current code
also cleans up the timer to early (it gets rearmed). So move it right
before the final cleanup (it seems to work).
Also unconditionally set up the idle_timer in intel_increase_pllclock.
If we're unlucky the timer might fire right away, rendering the call
in the modesetting teardown pointless.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With kms, interrupts now get disabled in the modesetting cleanup. So
free the error state afterwards, it currently gets allocated in
the interrupt handler.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
hotplug_work is queued by the hotplug interrupt and only either emits
a hotplug uevent or queues a crt poll slow-work. No other locking. So
it's safe to cancel this work _after_ irq's have been turned off. But
before the modesetting objects are destroyed because the hotplug
function accesses them (without locking).
The current code (for kms) only switches irqs off after modesetting
teardown, hence move the irq teardown into the modeset cleanup right
before the crtc cleanup.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is the first patch to clean up module unload races due to
outstanding timers/work. Preparatory step: Thou shalt not destroy
the workqueue when new work might still get enqued.
Now error_work gets queued by the hangcheck timer and only (atomically)
reads the chip wedged status. So cancel it right after the hangcheck
timer is killed. But the hangcheck is armed by interrupts, so move
everything after irqs are disabled.
Also change a del_timer to a del_timer_sync in the ums gem code, the
hangcheck timer is self-rearming.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
struct intel_dp contains both struct intel_encoder at the beginning (as
it's base-class) and an i2c adapater. When initializing, the i2c adapter
gets assigned
intel_encoder->ddc_adaptor = &intel_dp->adapter
and the generic intel_encode_destroy happily calls kfree on this pointer.
Ouch. Fix this by using a dp specific cleanup function.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit b9421ae8f3.
This warning was so prelevant, even for apparently working machines,
that it was just causing fear, anxiety and panic.
The root cause still remains, so we will add some better debugging when
we focus on fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=17021
Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 0f3ee801b3.
Enabling LVDS on pipe A was causing excessive wakeups on otherwise idle
systems due to i915 interrupts. So restrict the LVDS to pipe B once more,
whilst the issue is properly diagnosed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307
Reported-and-tested-by: Enrico Bandiello <enban@postal.uv.es>
Poked-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
This reverts commit ce17178094.
This commit has been independently bisected a few times as being the cause
of a s2ram failure.
Reported-and-tested-by: Kyle McMartin <kyle@mcmartin.ca>
Reported-and-tested-by: Andy Isaacson <adi@hexapodia.org>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
New pci ids for GT2 and GT2+ on desktop and mobile sandybridge,
and graphics device ids for server sandybridge. Also rename original
ids string to reflect GT1 version.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
MI_FLUSH is being deprecated, but still available on Sandybridge.
Make sure it's enabled as userspace still uses MI_FLUSH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sandybridge GTT has new cache control bits in PTE, which controls
graphics page cache in LLC or LLC/MLC, so we need to extend the mask
function to respect the new bits.
And set cache control to always LLC only by default on Gen6.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Arguably this is a bug in drm-core in that we should not be called twice
in succession with DPMS_ON, however this is still occuring and we see
FDI link training failures on the second call leading to the occassional
blank display. For the time being ignore the repeated call.
Original patch by Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We were passing garbage values into the panel-fitter control register
when disabling it on Ironlake - those values (filter modes and reserved
MBZ bits) would have then be re-used the next time panel-fitting was
enabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).
Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.
Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We reset intel_encoder for every matching encoder whilst iterating over
the encoders attached to this crtc when changing mode. As such in a
cloned configuration intel_encoder may not correspond to the correct
is_edp encoder.
By scoping intel_encoder to the loop, not only is the compiler able to
spot this mistake, we also improve readiability for ourselves.
[It might not be a mistake, within this function it is unclear as to
whether it is permissable for eDP to be cloned...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were failing when trying to allocate the resource for MMIO of the
MCHBAR because we forgot to specify what type of resource we wanted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Only stop trying if the aux channel sucessfully reports that the
transmission was completed, otherwise try again. On the 5th failure,
bail and report that something is amiss.
This fixes a sporadic failure in reading the EDID for my external panel
over DP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
If the VBIOS tells us the mapping of the SDVO device onto the DDC bus,
use it. However, if there is no VBIOS available that mapping is
uninitialised and we should fallback to our earlier guess.
Fix regression introduced in b1083333 (which in turn is a fix for the
regression caused by the introduction of this guess, 14571b4).
References:
Bug 29499 - [945GM] Screen disconnected because of missing VBIOS
https://bugs.freedesktop.org/show_bug.cgi?id=29499
Bug 15109 - i945GM fails to detect EDID on DVI port
https://bugzilla.kernel.org/show_bug.cgi?id=15109
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Adam Hill reported that his Arrandale system required a much longer, up
to 200x500us, wait for the panel to initialise or else modesetting would
fail.
References:
https://bugs.freedesktop.org/show_bug.cgi?id=29141
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Adam Hill <sidepipeuk@yahoo.co.uk>
i965 uses the Display Registers to compute the offset from the display
base so the new base does not need adjusting when flipping. The older
chipsets use a fence to access the display and so do perceive the
surface as linear and have a single base register which is reprogrammed
using the flip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: Marty Jack <martyj19@comcast.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
copy_to_user() returns the number of bytes remaining to be copied and
I'm pretty sure we want to return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
copy_to_user returns the number of bytes remaining to be copied, but we
want to return a negative error code here. These are returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
So set the coherent dma mask accordingly. This dma mask is only used
for physical objects, so it won't really matter allocation-wise.
Now this never really surfaced because sane 32bit kernels only have 1G
of lowmem. But some eager testers (distros?) still carry around the patch
to adjust lowmem via a kconfig option. And the kernel seems to favour
high allocations on boot-up, hence the overlay blowing up reliably.
Because the patch is tiny and nicely shows how broken gen2 is it's imho
worth to merge despite the fact that mucking around with the lowmem/
highmem division is (no longer) supported.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28318
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The vblank status bit is a sticky bit that must be cleared with a write
of '1' prior to polling for the next vblank.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
jbarnes: I'd still rather see a lock, but I think you're right that
we don't generally wait in code that needs not to miss an interrupt.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Partial revert of 9d0498a2bf.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This fixes blur-like screen corruption on the following card:
VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller [8086:29c2] (rev 10)
intel_sdvo_mode_set() should not return prematurely just because some
features are not supported.
https://bugzilla.kernel.org/show_bug.cgi?id=17151
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: Relax a couple more checks for failing LVDS modesetting]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 86f100b136.
The kref API requires the handlecount to be initialised to one on object
creation (so that kref_get() doesn't complain upon first use) so the
dalliance in the drivers is required in order to sink the initial
floating reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
drivers/gpu/drm/i915/intel_overlay.c: In function 'intel_overlay_print_error_state':
drivers/gpu/drm/i915/intel_overlay.c:1467: error: implicit declaration of function 'seq_printf'
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16811
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Andre Muller <andremuellerster@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only fallback to a set of default modes on a connector iff that
connector is known to be connected. The issue occurs that with limited
hardware which cannot probe a connector and so reports the
connector status as unknown will then attempt to retrieve the modes for
it during drm_helper_probe_single_connector_modes(). Should that fail,
the helper then generates a default set which fools the fb_helper and
causes havoc with the console and beyond.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling for a VGA device on an old system can be quite expensive,
causing latencies on the order of 600ms. As we hold the mode mutex for
this time and also need the same mutex to move the cursor, we trigger a
user-visible stall.
The real solution would involve improving the granulatity of the
locking and so perhaps performing some of the probing not under the lock
or some other updates can be done under different locks. Also reducing the
cost of probing for a non-existent monitor would be worthwhile. However,
exposing a parameter to disable polling is a simple workaround in the
meantime.
In order to accommodate users turning polling on and off at runtime, the
polling is potentially re-enabled on every probe. This is coupled to
the user calling xrandr, which seems to be a vaild time to reset the
polling timeout since the information on the connection has just been
updated. (The presumption being that all connections are probed in a
single xrandr pass, which is currently valid.)
References:
Bug 29536 - 2.6.35 causes ~600ms latency every 10s
https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bug 16265 - Why is kslowd accumulating so much CPU time?
https://bugzilla.kernel.org/show_bug.cgi?id=16265
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
digital underscan support regressed tv-out.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29985
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These VGT regs need to be programmed via the ring rather than
MMIO as on previous asics (r6xx/r7xx).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
We need it for PFIFO_INTR_CACHE_ERROR interrupt handling,
because nouveau_fifo_swmthd looks for matching gpuobj in
ramht_refs list.
It fixes kernel panic in nouveau_gpuobj_ref_find.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need it and it can lead to lock order inversions with respect
to drm_global_mutex, potentially causing dead locks.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It fixes a race between the TTM delayed work queue and the GEM IOCTLs
(fdo bug 29583) uncovered by the BKL removal.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The 7th entry in a lot of evergreen i2c gpio tables is partially
zeroed. Fix the entry.
Should fix the missing ddc entry in:
https://bugs.freedesktop.org/show_bug.cgi?id=29255
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tv parameter was added to disable the tv-out connector,
however, it caused a crash if it was set to 0 due to
drm_connector_init not getting called. If tv=0, don't
attempt to add the connector.
Might fix:
https://bugzilla.kernel.org/show_bug.cgi?id=17241
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV515
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code was originally for forcing some clocks on certain asics.
However, this code was later moved to asic specific functions
for all of the affected asics. The only users of the original
code at this point were r600, rv770, and evergreen and the code
was not relevant for those asics. So, remove it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit: 812d046915
drm/radeon/kms/r7xx: add workaround for hw issue with HDP flush
breaks on AGP boards since there is no VRAM gart table.
This patch fixes the issue by creating a VRAM scratch page so that
can be used on both AGP and PCIE.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29834
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rather than calling get_memory_clock and get_engine_clock,
used the tracked values from the pm code. Calling the tables
adds additional latency in the modesetting and pm paths.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Every driver used the default implementation. Fold that one into
the only callsite and drop the callback.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no point in jumping through two indirections. So kill one
and call the kernels agp functions directly.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The information supplied by userspace through these ioctls is only
accessible by dev->drw_idr. But there's no in-tree user of that.
Also userspace does not really care about return values of these ioctls,
either. Only hw/xfree86/dri/dri.c from the xserver actually checks the
return from adddraw and keeps on trying to create a kernel drawable
every time somebody creates a dri drawable. But since that's now a noop,
who cares.
Therefore it's safe to replace these three ioctls with noops and rip
out the implementation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers happily copy&pasted the default implementation without
checking whether this callback is used at all. It's not. Sigh.
Kill it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's not used by any driver. The destructor callback is unfortunately
used by the via driver in a rather convoluted piece of code used
to reimplement something resembling broken futexes. I didn't dare
to touch this code. But at least kill the needless NULL assignemt
in the sis driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's not used internally by any driver, only by some generic ioctls.
So don't export it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vgaarb: Wrap vga_(get|put) in CONFIG_VGA_ARB
drm/radeon/kms: add missing scratch update in dp_detect
drm/modes: Fix CVT-R modeline generation
drm: fix regression in drm locking since BKL removal.
drm/radeon/kms: remove stray radeon_i2c_destroy
drm: mm: fix range restricted allocations
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16651
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Adam Serbinski <adam@serbinksi.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This locking path needs proper auditing but probably too late for changes at this point for 2.6.36, so lets go with the quick fix, which is to drop the lock around schedule.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I missed this one in the i2c unification patch. This
is handled in the core radeon i2c code now.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the code cleanup in
7a6b2896f2 is the first bad commit
commit 7a6b2896f2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 2 15:02:15 2010 +0100
drm_mm: extract check_free_mm_node
I've botched up the range-restriction checks. The result is usually
an X server dying with SIGBUS in libpixman (software fallback rendering).
Change the code to adjust the start and end for range restricted
allocations. IMHO this even makes the code a bit clearer.
Fixes regression bug: https://bugs.freedesktop.org/show_bug.cgi?id=29738
Reported-by-Tested-by: Till MAtthiesen <entropy@everymail.net>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
If we keep hold of the mutex here, the process which currently holds the
buffer object will never be able to release it, causing a deadlock.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The "return" command is buggy on the original nv20, it jumps back to
the caller address as expected, but it doesn't clear the subroutine
active bit making the subsequent pushbuf calls fail with a "stack"
overflow.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The TMDS output of an nv11 was being detected as LVDS, because it uses
DCB type 2 for TMDS instead of type 4.
Reported-by: Bertrand VIEILLE <Vieille.Bertrand@free.fr>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When converting this to the new wait_for macro I inverted the wait
condition, which causes all sorts of problems. So correct it to fix
several failures caused by the bad wait (flickering, bad output
detection, tearing, etc.).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (33 commits)
drm/radeon/kms: fix typo in radeon_compute_pll_gain
drm/radeon/kms: try to detect tv vs monitor for underscan
drm/radeon/kms: fix sideport detection on newer rs880 boards
drm/radeon: fix passing wrong type to gem object create.
drm/radeon/kms: set encoder type to DVI for HDMI on evergreen
drm/radeon/kms: add back missing break in info ioctl
drm/radeon/kms: don't enable MSIs on AGP boards
drm/radeon/kms: fix agp mode setup on cards that use pcie bridges
drm: move dereference below check
drm: fix end of loop test
drm/radeon/kms: rework radeon_dp_detect() logic
drm/radeon/kms: add missing asic callback assignment for evergreen
drm/radeon/kms/DCE3+: switch pads to ddc mode when going i2c
drm/radeon/kms/pm: bail early if nothing's changing
drm/radeon/kms/atom: clean up dig atom handling
drm/radeon/kms: DCE3/4 transmitter fixes
drm/radeon/kms: rework encoder handling
drm/radeon/kms: DCE3/4 AdjustPixelPll updates
drm/radeon: Fix stack data leak
drm/radeon/kms: fix GTT/VRAM overlapping test
...
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix earlier mistake when fixing merge conflict
drm/nvc0: fix thinko in instmem suspend/resume
drm/nouveau: Workaround missing GPIO tables on an Apple iMac G4 NV18.
drm/nouveau: Add TV-out quirk for an MSI nForce2 IGP.
drm/nv50-nvc0: ramht_size is meant to be in bytes, not entries
drm/nouveau: punt some more log messages to debug level
drm/nouveau: remove warning about unknown tmds table revisions
drm/nouveau: check for error when allocating/mapping dummy page
drm/nouveau: fix race condition when under memory pressure
drm/nv50: fix minor thinko from nvc0 changes
drm/nouveau: Don't try DDC on the dummy I2C channel.
Looks like this got copied from the ddx wrong.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When enabling underscan for hdmi monitors, attempt to detect
whether we are driving a TV or a monitor. The should hopefully
prevent underscan from being enabled on monitors attached via
hdmi that do not overscan the image. Only enable underscan
if the mode is a common hdtv mode (480p, 720p, etc.).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The meaning of ucMemoryType changed on recent boards, however,
ulBootUpSidePortClock should be set properly across all boards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are passing a ttm type when we want to pass true/false.
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (58 commits)
drm/i915,intel_agp: Add support for Sandybridge D0
drm/i915: fix render pipe control notify on sandybridge
agp/intel: set 40-bit dma mask on Sandybridge
drm/i915: Remove the conflicting BUG_ON()
drm/i915/suspend: s/IS_IRONLAKE/HAS_PCH_SPLIT/
drm/i915/suspend: Flush register writes before busy-waiting.
i915: disable DAC on Ironlake also when doing CRT load detection.
drm/i915: wait for actual vblank, not just 20ms
drm/i915: make sure eDP PLL is enabled at the right time
drm/i915: fix VGA plane disable for Ironlake+
drm/i915: eDP mode set sequence corrections
drm/i915: add panel reset workaround
drm/i915: Enable RC6 on Ironlake.
drm/i915/sdvo: Only set is_lvds if we have a valid fixed mode.
drm/i915: Set up a render context on Ironlake
drm/i915 invalidate indirect state pointers at end of ring exec
drm/i915: Wake-up wait_request() from elapsed hang-check (v2)
drm/i915: Apply i830 errata for cursor alignment
drm/i915: Only update i845/i865 CURBASE when disabled (v2)
drm/i915: FBC is updated within set_base() so remove second call in mode_set()
...
This one is missed in last pipe control fix for sandybridge,
that really unmask interrupt bit for notify in render engine IMR.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We now attempt to free "active" objects following a GPU hang as either
the GPU will be reset or the hang is permenant. In either case, the GPU
writes will not be flushed to main memory and it should be safe to
return that memory back to the system.
The BUG_ON(active) is thus overkill and can erroneously fire after a
EIO.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
For the shared paths on the next generation chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Like on Sandybridge, disabling the DAC here when doing CRT load detect
avoids forever hangs waiting on the hardware.
test procedure on HP 2740p:
boot with no VGA plugged in, start X,
plug in VGA monitor (1280x1024)
chvt 3
machine hangs waiting forever.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Waiting for a hard coded 20ms isn't always enough to make sure a vblank
period has actually occurred, so add code to make sure we really have
passed through a vblank period (or that the pipe is off when disabling).
This prevents problems with mode setting and link training, and seems to
fix a bug like https://bugs.freedesktop.org/show_bug.cgi?id=29278, but
on an HP 8440p instead. Hopefully also fixes
https://bugs.freedesktop.org/show_bug.cgi?id=29141.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes the pink line that shows up with some hdmi monitors. This
will need to be revisited when audio support is added.
Fixes:
http://bugs.freedesktop.org/show_bug.cgi?id=27452
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noone is using tty argument so let's get rid of it.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This seems to have gotten lost in the hyper-z merge.
Noticed by legume on IRC.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Asics that use an AGP to PCIE bridge don't have the AGP_STATUS
register so just use whatever mode the host side setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"fb_helper_conn" is dereferenced before the check for NULL. It's never
actually NULL here, so this is mostly to keep the static checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"agpmem" is never NULL here because it is the list cursor of a
list_for_each_entry() list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the connector is eDP, it can only be DP, not TMDS.
Always set the detected sink type. If the sink is
detected as non-DP, but there is no EDID, you can still
manually force the port on. If the sink type is DP
and there's no DPCD, there's no way to force the monitor
on since you need both ends to train the link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pins for ddc and aux are shared so you need to switch the
mode when doing ddc. The ProcessAuxChannel table already sets
the pin mode to DP. This should fix unreliable ddc issues
on DP ports using non-DP monitors.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows the tables to be run in some additional cases
where the connector info isn't necessary.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- INIT action takes the actual connector type id, not the enum id
- some evergreen cards have the ENABLE_OUTPUT/DISABLE_OUTPUT actions
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On most newer asics, digital encoders have two links each
and they can be used independantly. As such, treat them as
separate encoders otherwise the individual links will not
get programmed properly at modeset time.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add options necessary bits for:
- SS on DP
- SS on LVDS
- set clocks right for DP
- deep color on hdmi (needs additional encoder and edid work as well)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always zero-init a structure on the stack which is returned by a
function. Otherwise you may leak random stack data from previous
function calls.
This fixes the following warning I was seeing:
CC [M] drivers/gpu/drm/radeon/radeon_atombios.o
drivers/gpu/drm/radeon/radeon_atombios.c: In function "radeon_atom_get_hpd_info_from_gpio":
drivers/gpu/drm/radeon/radeon_atombios.c:261: warning: "hpd.plugged_state" is used uninitialized in this function
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GTT/VRAM overlapping test had a typo which leaded to not
detecting case when vram_end > gtt_end. This patch fix the
logic and should fix#16574
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to make sure the eDP PLL is enabled before the pipes or planes,
so do it as part of the DP prepare mode set function.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to use I/O port instructions to access VGA registers on
Ironlake+, and it doesn't hurt on other platforms, so switch the VGA
plane disable function over to using them. Move it to init time as well
while we're at it, no need to repeatedly disable the VGA plane with
every mode set and DPMS event.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We should disable the panel first when shutting down an eDP link. And
when turning one on, the panel needs to be enabled before link training
or eDP I/O won't be enabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ironlake requires that we clear the reset panel bit during power
sequences and restore it afterwards. Uncondtionally add code to do that
since it should be harmless on SNB+.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With the current screwed but its ABI, ioctls for the drm, Linus pointed out that we could allow userspace to specify the allocation size, but we pass it to the driver which then uses it blindly to store a struct. Now if userspace specifies the allocation size as smaller than the driver needs, the driver can possibly overwrite memory.
This patch restructures the driver ioctls so we store the structure size we are expecting, and make sure we allocate at least that size. The copy from/to userspace are still restricted to the size the user specifies, this allows ioctl structs to grow on both sides of the equation.
Up until now we didn't really use the DRM_IOCTL defines in the kernel, so this cleans them up and adds them for nouveau.
v2:
fix nouveau pushbuf arg (thanks to Ben for pointing it out)
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
non-critical issue, CVE-2010-2803
Userspace controls the amount of memory to be allocate, so it can
get the ioctl to allocate more memory than the kernel uses, and get
access to kernel stack. This can only be done for processes authenticated
to the X server for DRI access, and if the user has DRI access.
Fix is to just memset the data to 0 if the user doesn't copy into
it in the first place.
Reported-by: Kees Cook <kees@ubuntu.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should fix the reported TV-out load detection false positives
(fdo bug 29455).
Reported-by: Vlado Plaga <rechner@vlado-do.de>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The blob also thinks there's a TV connected, so hardware bug...
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This message is apparently confusing people, and is being blamed for some
modesetting issues. Lets remove the message, and instead replace it
with an unconditional printout of the table revision.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When VRAM is running out it's possible that the client's push buffers get
evicted to main memory. When they're validated back in, the GPU may
be used for the copy back to VRAM, but the existing synchronisation code
only deals with inter-channel sync, not sync between PFIFO and PGRAPH on
the same channel. This leads to PFIFO fetching from command buffers that
haven't quite been copied by PGRAPH yet.
This patch marks push buffers as so, and forces any GPU-assisted buffer
moves to be done on a different channel, which triggers the correct
synchronisation to happen before we submit them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* git://git.infradead.org/~dwmw2/ideapad-2.6:
Call acpi_video_register() in intel_opregion_init() failure path
ideapad: Only allow camera state to be set to 0 or 1
ideapad: Stop using global variables
Add Lenovo ideapad driver
If i915 opregion is present, the acpi_video driver doesn't register
itself immediately; it defers that until the i915 opregion code is done.
But if that *fails*, the acpi_video driver was never getting registered.
And thus I have no backlight support on my Lenovo IdeaPad S10-3.
Call acpi_video_register() on the failure path, and it works again.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Matthew Garrett <mjg@redhat.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (55 commits)
io-mapping: move asm include inside the config option
vgaarb: drop vga.h include
drm/radeon: Add probing of clocks from device-tree
drm/radeon: drop old and broken mesa warning
drm/radeon: Fix pci_map_page() error checking
drm: Remove count_lock for calling lastclose() after 58474713 (v2)
drm/radeon/kms: allow FG_ALPHA_VALUE on r5xx
drm/radeon/kms: another r6xx/r7xx CS checker fix
DRM: Replace kmalloc/memset combos with kzalloc
drm: expand gamma_set
drm/edid: Split mode lists out to their own header for readability
drm/edid: Rewrite mode parse to use the generic detailed block walk
drm/edid: Add detailed block walk for VTB extensions
drm/edid: Add detailed block walk for CEA extensions
drm: Remove unused fields from drm_display_info
drm: Use ENOENT consistently for the error return for an unmatched handle.
drm/radeon/kms: mark 3D power states as performance
drm: Only set DPMS once on the CRTC not after every encoder.
drm/radeon/kms: add additional quirk for Acer rv620 laptop
drm: Propagate error code from fb_create()
...
Fix up trivial conflicts in drivers/gpu/drm/drm_edid.c
When we find no ROM we understand and a device-tree is present, see
if we can retreive clock info from there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This never really got fixed in mesa, and the kernel deals with the problem
just fine, so don't got reporting things that confuse people.
Signed-off-by: Dave Airlie <airlied@redhat.com>
0 is a valid DMA address from pci_map_page(), use pci_dma_mapping_error()
instead to check for errors
[airlied: fix warning + two other places with errors.]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a CS checker fix. I need this for FP16 alpha-test.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
add default case for buffer formats
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Andre Maasikas <amaasikas@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently most, if not all, memory allocation in drm_bufs.c is followed by initializing the memory with 0.
Replace the use of kmalloc+memset with kzalloc.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jesse's initial patch commit said:
"At panic time (i.e. when oops_in_progress is set) we should try a bit
harder to update the screen and make sure output gets to the VT, since
some drivers are capable of flipping back to it.
So make sure we try to unblank and update the display if called from a
panic context."
I've enhanced this to add a flag to the vc that console layer can set to
indicate they want this behaviour to occur. This also adds support to
fbcon for that flag and adds an fb flag for drivers to indicate they want
to use the support. It enables this for KMS drivers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Expand the crtc_gamma_set function to accept a starting offset. The
reason for this is to eventually use this function for setcolreg from
drm_fb_helper.c. The fbdev colormap function can start at any offset in
the color map.
Signed-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This brings us in line with the EDID spec recommendation for mode
priority sorting. We still don't extract all the modes we could from
VTB, but VTB is so rare in the wild that I'm not really concerned.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is consistent with trying to access a filename that not exist
within a directory which is a good analogy here. The main reason for the
change is that it is easy to confuse the error code of EBADF as an
performing an ioctl on an invalid file descriptor (rather than an
unknown object).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes lack of power saving with multiple heads on
some desktop cards.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16474
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Change the interface to expect a PTR_ERR specifing the real error code
as opposed to assuming a NULL return => -EINVAL. Just once the user may
not be at fault!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Smatch complained that the ERR_PTR from hwmon_device_register() wasn't
handled. I added some error handling in radeon_hwmon_init() to silence
the warning.
Unfortunately errors from radeon_pm_init() aren't handled so this
doesn't really make a difference beyond silencing the warning.
Also I changed DRM_ERROR() to dev_err() which is the new preferred
method.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
router objects are found on systems that use a mux to control
ddc line to connector routing or to control the actual clock and data
routing from the chip to the connectors. This patch implements ddc line
routing.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Handle asic specific table to hw mappings in
combios_setup_i2c_bus() directly. This allows us
to remove most of the combios quirks and clean up
the i2c bus setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we added i2c buses as needed when enumerating connectors
power management, etc. This only exposed the actual buses used and
could have lead to the same buse getting created more than once if
one buses was used for more than one purpose. This patch sets up
all i2c buses on the card in one place and users of the buses just
point back to the one instance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- buffer offsets in the base regs are 256b aligned so
shift properly when comparing, fixed by Andre Maasikas
- mipmap size was calculated wrong when nlevel=0
- texture bo offsets were used after the bo base address was added
- vertex resource size register is size - 1, not size
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Andre Maasikas <amaasikas@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(For some reason I thought that went in ages ago ...)
This fixes support for PCI domains in what should hopefully be a backward
compatible way along with a change to libdrm.
When the interface version is set to 1.4, we assume userspace understands
domains and the world is at peace. We thus pass proper domain numbers
instead of 0 to userspace.
The newer libdrm will then try 1.4 first, and fallback to 1.1, along with
ignoring domains in the later case (well, except on alpha of course)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: (27 commits)
drm/nvc0: fix typo in PRAMIN flush
drm/nouveau: Fix DCB TMDS config parsing.
drm/nv30: Fix PFB init for nv31.
drm/nv04: Fix up SGRAM density detection.
drm/i2c/ch7006: Don't use POWER_LEVEL_FULL_POWER_OFF on early chip versions.
drm/nouveau: Init dcb->or on cards that have no usable DCB table.
drm/nouveau: reduce severity of some "error" messages
drm/nvc0: backup bar3 channel on suspend
drm/nouveau: implement init table opcodex 0x5e and 0x9a
drm/nouveau: implement init table op 0x57, INIT_LTIME
drm/nvc0: implement crtc pll setting
drm/nvc0: fix evo dma object so we display something
drm/nvc0: rudimentary instmem support
drm/nvc0: implement memory detection
drm/nvc0: allow INIT_GPIO
drm/nvc0: starting point for GF100 support, everything stubbed
drm/nv30: Workaround dual TMDS brain damage.
drm/nouveau: No need to set slave TV encoder configs explicitly.
drm/nv17-nv4x: Attempt to init some external TMDS transmitters.
drm/nv10: Fix up switching of NV10TCL_DMA_VTXBUF.
...
This hasn't mattered up until the ioctl started using the value, and it fell
apart.
fixes fd.o 29340, Ubuntu LP 606081
[airlied: cleaned up whitespace and don't need an error before pushing]
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
RC6 allows the GPU to enter a lower power state when the GPU is idle.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[anholt: Fixed the !renderctx error path to actually not enable RC6.]
Signed-off-by: Eric Anholt <eric@anholt.net>
If we have failed to ascertain the fixed mode for the LVDS panel, then
trust the pixel clock ranges reported for the connection when determing
valid modes. This makes intel_sdvo_mode_valid() consistent with
intel_lvds_mode_valid() which is also a no-op is there is no fixed mode
defined. (Since the mode is both validated by SDVO and LVDS, why are
checking against an LVDS fixed mode in SDVO...)
By only defining is_lvds to be true when we actually have an LVDS output
with a fixed mode, we avoid various potential NULL deferences where the
assumption is made that all LVDS outputs have a fixed mode.
References:
Bug 29449 - [Q35] failure to read EDID/vbios for LVDS, no mode => no output
https://bugs.freedesktop.org/show_bug.cgi?id=29449
The primary failure in this bug is not finding the EDID and determining
the correct fixed panel mode. However, this patch should fix the
secondary issue of not enabling any of the standard modes for the panel
either.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
RC6 power state requires a logical render context in place for saving
render context.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is required by the spec, and without this some 3D programs will
hang after resume from RC6 we enable that.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If our watchdog fires and we see that the GPU is idle, but that we
are still waiting on an interrupt, forcibly wake-up the waiter.
i915_do_wait_request() should not be racy, yet there are persistent
reports that 945GM hangs whilst the GPU is idle. This implies that the
hardware is not quite as coherent as the documentation claims - a write
followed by a flush is supposed to be coherent in main memory before the
flush is retired and the irq is emitted. This seems to be a sensible and
elegant guard to force the wait to timeout.
v2: Daniel Vetter pointed out that a warning would be useful to explain
why the machine appeared to stall.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
i830 requires 32bpp cursors to be aligned to 16KB, so we have to expose
the alignment parameter to i915_gem_attach_phys_object().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The i845 and i865 have a peculiarlity in that CURBASE is not the trigger
for the vsync update of the cursor registers but instead the
modification of that register is prohibited whilst the cursor is
enabled. Reorder the write sequence for CURPOS, CURCNTR and CURBASE on
i845 to i865 to match.
v2: Remove the checks for i845/i865 from within i9xx_cursor_update()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The FBC is dependent upon a few details of the framebuffer so it is
required to be updated within set_base(), so remove the redundant call
from mode_set().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a new macro, wait_for, to simplify the act of waiting on a register
to change state. wait_for() takes three arguments, the condition to
inspect on every loop, the maximum amount of time to wait and whether to
yield the cpu for a length of time after each check.
v2: Upgrade failure messages to DRM_ERROR on the suggestion of
Eric Anholt. We do not expect to hit these conditions as they reflect
programming errors, so if we do we want to be notified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The cleanup path for early abort failed to nullify the gem_buffer. The
likely consequence of this is zero, since a failure here should mean
aborting the module load.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Previously, we only remembered to update the watermarks for i9xx, and
incorrectly assumed that the crtc->enabled flag was valid at that point
in the dpms cycle.
Note that on my x201s this makes a SR bug on pipe 1 much easier to hit.
(Since before this patch when disabling pipe 0, we either didn't update
the watermarks at all, or when we did we still thought we had two pipes
enabled and so disabled SR.)
References:
Bug 28969 - [Arrandale] Screen flickers, suspect Self-Refresh
https://bugs.freedesktop.org/show_bug.cgi?id=28969
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Within i915_opregion.c there are two blocks of semantically identical
ASLE response codes defined. Only one of those matches the ACPI IGD
OpRegion Specification 0.1, use those.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
shmfs doesn't actually implement i_ops->truncate() so we were not
immedatiately releasing the backing pages when shrinking the gfx cache
under OOM. Instead use a combination of truncate_inode_pages() and
i_ops->truncate_range() as is used by shmem_delete_inode().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Writing to the DSPBASE register triggers the double-buffered update to
all the control registers, so always write it last in the update
sequence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
v2: Hook in DP paths to keep FULLSCREEN panel fitting on eDP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Directly read the GTT mapping for the contents of the batch buffers
rather than relying on possibly stale CPU caches. Also for completeness
scan the flushing/inactive lists for the current buffers - we are
collecting error state after all.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to reduce the penalty of fallbacks under memory pressure and to
avoid a potential immediate ping-pong of evicting a mmaped buffer, we
move the object to the tail of the inactive list when a page is freshly
faulted or the object is moved into the CPU domain.
We choose not to protect the CPU objects from casual eviction,
preferring to keep the GPU active for as long as possible.
v2: Daniel Vetter found a bug where I forgot that pinned objects are
kept off the inactive list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Based in a large part upon Daniel Vetter's implementation and adapted
for handling multiple rings in a single pass.
This should lead to better gtt usage and fixes the page-fault-of-doom
triggered. The fairness is provided by scanning through the GTT space
amalgamating space in rendering order. As soon as we have a contiguous
space in the GTT large enough for the new object (and its alignment),
evict any object which lies within that space. This should keep more
objects resident in the GTT.
Doing throughput testing on a PineView machine with cairo-perf-trace
indicates that there is very little difference with the new LRU scan,
perhaps a small improvement... Except oddly for the poppler trace.
Reference:
Bug 15911 - Intermittent X crash (freeze)
https://bugzilla.kernel.org/show_bug.cgi?id=15911
Bug 20152 - cannot view JPG in firefox when running UXA
https://bugs.freedesktop.org/show_bug.cgi?id=20152
Bug 24369 - Hang when scrolling firefox page with window in front
https://bugs.freedesktop.org/show_bug.cgi?id=24369
Bug 28478 - Intermittent graphics lockups due to overflow/loop
https://bugs.freedesktop.org/show_bug.cgi?id=28478
v2: Attempt to clarify the logic and order of eviction through the use
of comments and macros.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
The eviction code is the gnarly underbelly of memory management, and is
clearer if kept separated from the normal domain management in GEM.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This will be used by the eviction logic to maintain fairness between the
rings.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This does two little changes:
- Add an alignment parameter for evict_something. It's not really great to
whack a carefully sized hole into the gtt with the wrong alignment.
Especially since the fallback path is a full evict.
- With the inactive scan stuff we need to evict more that one object, so
move the unbind call into the helper function that scans for the object
to be evicted, too. And adjust its name.
No functional changes in this patch, just preparation.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to properly track bound objects, they need to exist on one of
the inactive/active lists or be pinned. As this is a requirement, do the
work inside i915_gem_bind_to_gtt() rather than dotted around the
callsites.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
v2: Add the interrupt status and address.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Using dev_priv__ avoids sparse complaining about shadowed variables in
the *LP_RING() macros.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
As the function has been reduced to a store plus increment, the body is
now smaller than the call so inline it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we check that the ringbuffer will not wrap upon emission, we do not
need to check that incrementing the tail wrapped every time. However, we
do upon advancing just in case the tail is now pointing at the very end
of the ring.
Likewise we can account for the space used during emission in begin()
and avoid decrementing it for every emit.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The tail is quadword aligned, so we can add two MI_NOOP as a time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
