Disable ftrace during kexec. Same as on x86/powerpc.
ac4414e "powerpc/kdump: Disable ftrace during kexec".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for XZ compressed kernel. Same as on x86 and sh.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement write protection for kernel modules text and read-only
data sections by implementing set_memory_[ro|rw] on s390.
Since s390 has no execute bit in the pte's NX is not supported.
set_memory_[ro|rw] will only work on normal pages and not on
large pages, so in case a large page should be modified bail
out with a warning.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Newer gcc versions offer an architecture-independent option to check
the stack size and warn if it reaches a certain limit. This option
already existed for s390 by using -mwarn-dynamicstack. Since one
stack check option is enough remove the s390 specific stack check
but keep the option that warns about dynamic stack usage because
that is not covered by the generic option.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Adds support for the hardware watchdog found in Ingenic's jz4740
System-on-Chip.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Update p1022 sata compatible to "fsl,p1022-sata", "fsl,pq-sata-v2".
p1022ds sata controller is v2 version comparing previous FSL sata
controller, for example, mpc8536.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Intel Archiecture Software Developer's Manual section 7.1.3 specifies that a
core serializing instruction such as "cpuid" should be executed on _each_ core
before the new instruction is made visible.
Failure to do so can lead to unspecified behavior (Intel XMC erratas include
General Protection Fault in the list), so we should avoid this at all cost.
This problem can affect modified code executed by interrupt handlers after
interrupt are re-enabled at the end of stop_machine, because no core serializing
instruction is executed between the code modification and the moment interrupts
are reenabled.
Because stop_machine_text_poke performs the text modification from the first CPU
decrementing stop_machine_first, modified code executed in thread context is
also affected by this problem. To explain why, we have to split the CPUs in two
categories: the CPU that initiates the text modification (calls text_poke_smp)
and all the others. The scheduler, executed on all other CPUs after
stop_machine, issues an "iret" core serializing instruction, and therefore
handles core serialization for all these CPUs. However, the text modification
initiator can continue its execution on the same thread and access the modified
text without any scheduler call. Given that the CPU that initiates the code
modification is not guaranteed to be the one actually performing the code
modification, it falls into the XMC errata.
Q: Isn't this executed from an IPI handler, which will return with IRET (a
serializing instruction) anyway?
A: No, now stop_machine uses per-cpu workqueue, so that handler will be
executed from worker threads. There is no iret anymore.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
LKML-Reference: <20110303160137.GB1590@Krystal>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: <stable@kernel.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit da3ed89e7c added
'fsl,qoriq-gpio' compatiable searching in the old way
using for_each_compatible_node(). But the driver have
previously been changed to use a struct of_device_id
compatible list passed to for_each_matching_node().
Add 'fsl,qoriq-gpio' compatiable to the existing
compatible list instead of adding another
for_each_compatible_node() loop.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MUSB driver doesn't see its platform device on DM644x EVM board anymore
since commit 73b089b052 (usb: musb: split davinci
to its own platform_driver) because the new probe is called as subsys_initcall()
now, and the device is registered later than that by the board code. Move the
registration to davinci_evm_init() -- it's safe to do so because the MUSB core
device still gets initialized as fs_initcall() -- which is late enough for the
I2C GPIO expander (which controls VBUS) to be initialized.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds definitions for spi devices on the tnetv107x evm platform.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SSP configuration and pin muxing info for tnetv107x
evm boards.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds an SSP platform device definition for the tnetv107x soc family.
The clock lookup entry has also been updated to match.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The MPC852 based mgsuvd board from Keymile was initially ported,
but later on not developed further. This patch removes the respective
files to decrease merging conflicts and unneeded maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mgcoge board from keymile is now base for some other
similar boards. Therefore the board specific name mgcoge
was renamed to a generic name km82xx. Additionally some
enhancements were made:
- rework partition table in dts file
- add cpm2_pio_c gpio controller in dts file
- update defconfig
- add pin description for SCC1
- add pin description and configuration for USB
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside the MPC 8360 based board kmeter1 other km83xx boards
from keymile will follow. Therefore the board specific naming
kmeter1 for functions and files were replaced with km83xx.
Additionally some updates were made:
- update defconfig for 2.6.38
- rework flash partitioning in dts file
- add gpio controller for qe_pio_c in dts
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This erratum can occur if a single-precision floating-point,
double-precision floating-point or vector floating-point instruction on a
mispredicted branch path signals one of the floating-point data interrupts
which are enabled by the SPEFSCR (FINVE, FDBZE, FUNFE or FOVFE bits). This
interrupt must be recorded in a one-cycle window when the misprediction is
resolved. If this extremely rare event should occur, the result could be:
The SPE Data Exception from the mispredicted path may be reported
erroneously if a single-precision floating-point, double-precision
floating-point or vector floating-point instruction is the second
instruction on the correct branch path.
According to errata description, some efp instructions which are not
supposed to trigger SPE exceptions can trigger the exceptions in this case.
However, as we haven't emulated these instructions here, a signal will
send to userspace, and userspace application would exit.
This patch re-issue the efp instruction that we haven't emulated,
so that hardware can properly execute it again if this case happen.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller v2.1:
- New MSI inbound window
- Same Inbound windows address as PCIe controller v1.x
Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window
FSL PCIe controller v2.2 and v2.3:
- Different addresses for PCIe inbound window 3,2,1
- Exposed PCIe inbound window 0
- New PCIe interrupt status register
Added new config and interrupt Status register to struct ccsr_pci & updated
pit_t array size to reflect the 4 inbound windows.
Device tree is used to maintain backward compatibility i.e. update inbound
window 1 index depending upon "compatible" field witin PCIE node.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the spin table is located in the linear mapping (which can happen if
we have 4G or more of memory) we need to access the spin table via a
cacheable coherent mapping like we do on ppc32 (and do explicit cache
flush).
See the following commit for the ppc32 version of this issue:
commit d1d47ec6e6
Author: Peter Tyser <ptyser@xes-inc.com>
Date: Fri Dec 18 16:50:37 2009 -0600
powerpc/85xx: Fix SMP when "cpu-release-addr" is in lowmem
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch includes the implementation of the clock gating
for System MMU. Initially, all System MMUs are not asserted
the system clock. Asserting the system clock to a System MMU
is enabled only when s5p_sysmmu_enable() is called. Likewise,
it is disabled only when s5p_sysmmu_disable() is called.
Therefore, clock gating on System MMUs are still invisible to
the outside of the System MMU driver.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch includes the following enhancements for System MMU:
- Enhanced readability
- Removal of unused data structures or their members
- Simplified function definitions
- Corrections of some logical errors
- Full compliance with Linux coding style
- Simpler way of registering callback functions of System MMU faults
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for gpio interrupts on Samsung EXYNOS4 platform.
Common s5p-gpioint.c code is used for handling gpio interrupts. Each gpio
line that needs gpio interrupt support must be later registered with
s5p_register_gpio_interrupt() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes all global data from common s5p gpio interrupt
handler code. This enables to reuse this code on EXYNOS4 platform.
Instead of global data (IRQ_GPIOINT interrupt number,
S5P_GPIOINT_GROUP_MAXNR groups count), a s5p_register_gpioint_bank()
function is introduced. It is aimed to be called from gpiolib init.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch performs a global cleanup in s5p gpio interrupt support code.
The code is prepared for upcoming support for gpio interrupts on EXYNOS4
platform, which has 2 gpio banks (regions) instead of one (like on
S5PC110 and S5PC100).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing GPYx gpio banks on Samsung EXYNOS4 platform.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The cpufreq init function is referenced from the driver structure and
we don't appear to have annotations which allow us to mark that it'll
never be called after system init, causing the linker consistency
infrastructure to complain. Just remove the __init annotation to avoid
noise from the build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the SMDKV310 board.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The keypad IF on EXYNOS4 uses 100MHz from PERIR functional
block for clocks, this patch updates the same.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates the keypad IF base address in the memory map
for EXYNOS4.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the samsung_keypad_cfg_gpio() for EXYNOS4.
Now, this helpers are only for keypad operating in PORT-0.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The EDGE Port module of some ColdFire parts using the intc-simr interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The EDGE Port module of some ColdFire parts using the intc-2 interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5407/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5407/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5407/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/532x/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:54:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5307/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5307/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5307/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/527x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:38:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:39:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:54:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:55:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5272/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:67:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:68:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:69:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5249/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/523x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:38:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
rch/m68knommu/platform/520x/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5206e/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast CC kernel/panic.o
arch/m68knommu/platform/5206e/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206e/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5206/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The intc-simr interrupt controller on some ColdFire CPUs has a set range of
interrupts its supports (64 through 128 or 192 depending on model). We
shouldn't be setting this handler for every possible interrupt from 0 to
255. Set more appropriate limits, and this means we can drop the interrupt
number check in the mask and unmask routines.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Use a proper irq_startup() routine to intialize the interrupt priority
and level register in the ColdFire intc-2 controller code. We shouldn't
be checking if the priority/level has been set on every unmask operation.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The intc-2 interrupt controller on some ColdFire CPUs has a set range of
interrupts its supports (64 through 128 or 192 depending on model). We
shouldn't be setting this handler for every possible interrupt from 0 to
255. Set more appropriate limits, and this means we can drop the interrupt
number check in the mask and unmask routines.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The FireBee is a ColdFire 5475 based board. Add a configuration option
to support it, and the basic platform flash layout code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Most ColdFire CPUs have an internal peripheral set that can be mapped at
a user selectable address. Different ColdFire parts either use an MBAR
register of an IPSBAR register to map the peripheral region. Most boards
use the Freescale default mappings - but not all.
Make the setting of the MBAR or IPSBAR register configurable. And only make
the selection available on the appropriate ColdFire CPU types.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Different ColdFire CPUs have different ways of defining where their
internal peripheral registers sit in their address space. Some use an
MBAR register, some use and IPSBAR register, some have a fixed mapping.
Now that most of the peripheral address definitions have been cleaned up
we can clean up the setting of the MBAR and IPSBAR defines to limit them
to just where they are needed (and where they actually exist).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In some of the RAM size autodetection code on ColdFire CPU startup
we reference DRAM registers relative to the MBAR register. Not all of
the supported ColdFire CPUs have an MBAR, and currently this works
because we fake an MBAR address on those registers. In an effort to
clean this up, and eventually remove the fake MBAR setting make the
DRAM register address definitions actually contain the MBAR (or IPSBAR
as appropriate) value as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Not all ColdFire CPUs that use the old style timer hardware module use
an MBAR set peripheral region. Move the TIMER base address defines to the
per-CPU header files where we can set it correctly based on how the
peripherals are mapped - instead of using a fake MBAR for some platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The base addresses of the ColdFire DMA unit registers belong with
all the other address definitions in the per-cpu headers. The current
definitions assume they are relative to an MBAR register. Not all
ColdFire CPUs have an MBAR register. A clean address define can only
be acheived in the per-cpu headers along with all the other chips
peripheral base addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 528x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 527x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 523x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5207 and 5208 CPUs have fixed peripheral addresses.
They do not use the setable peripheral address registers like the MBAR
and IPSBAR used on many other ColdFire parts. Don't use fake values
of MBAR and IPSBAR when using peripheral addresses for them, there
is no need to.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The PIT hardware timer module used in some ColdFire CPU's is not always
addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and
5208 have fixed peripheral addresses. So lets not define the register
addresses of the PIT relative to an IPSBAR definition. Move the base
address definitions into the per-part headers. This is a lot more consistent
since all the other peripheral base addresses are defined in the per-part
header files already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the bogus definition of the MBAR register for the ColdFire 532x
family. It doesn't have an MBAR register, its peripheral registers are
at fixed addresses and are not relative to a settable base.
All the code that relyed on this definition existing has been cleaned
up. The register address definitions now include the base as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 54xx family shares the same interrupt controller used
on the 523x, 527x and 528x ColdFire parts, but it isn't offset
relative to the IPSBAR register. The 54xx doesn't have an IPSBAR
register.
By including the base address of the peripheral registers in the register
definitions (MCFICM_INTC0 and MCFICM_INTC1 in this case) we can avoid
having to define a fake IPSBAR for the 54xx. And this makes the register
address definitions of these more consistent, the majority of the other
register address defines include the peripheral base address already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MBAR2 register is only used on the ColdFire 5249 part, so move its
definition out of the common coldfire.h and into the 5249 support header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
/me idly wonders what sets the handlers for this chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
That handler lacks the minimal checks for action being zero etc. Keep
the weird flow - ack before handling - intact and call into
handle_simple_irq which does the right thing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
LKML-Reference: <20110202212552.413849952@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reset vector can be setup by bootloader and kernel doens't need
to touch it. If you require to setup reset vector, please use
CONFIG_MANUAL_RESET_VECTOR throught menuconfig.
It is not possible to setup address 0x0 as reset address because
make no sense to set it up at all.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: John Williams <john.williams@petalogix.com>
If soft reset falls through with no hardware assisted reset, the best
we can do is jump to the reset vector and see what the bootloader left
for us.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: John Williams <john.williams@petalogix.com>
Microblaze vector table stores several vectors (reset, user exception,
interrupt, debug exception and hardware exception).
All these functions can be below address 0x10000. If they are, wrong
vector table is genarated because jump is not setup from two instructions
(imm upper 16bit and brai lower 16bit).
Adding specific offset prevent problem if address is below 0x10000.
For this case only brai instruction is used.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Some chained IRQ handlers are written to cope with primary chips of
potentially different flow types. Whether this a sensible thing to do
is a point of contention.
This patch introduces entry/exit functions for chained handlers which
infer the flow type of the primary chip as fasteoi or level-type by
checking whether or not the ->irq_eoi function pointer is present and
calling back to the primary chip as necessary. Other methods of flow
control are not considered.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds the device definitions, platform specific initialization
and clocks for SATA on ARMLEX4210.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
native_flush_tlb_others() is called from:
flush_tlb_current_task()
flush_tlb_mm()
flush_tlb_page()
All these functions disable preemption explicitly, so we can use
smp_processor_id() instead of get_cpu() and put_cpu().
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Cc: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <4D7EC791.4040003@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch add new syscalls to x86_64
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch adds new syscalls to x86_32
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The variable pm_flags is used to prevent APM from being enabled
along with ACPI, which would lead to problems. However, acpi_init()
is always called before apm_init() and after acpi_init() has
returned, it is known whether or not ACPI will be used. Namely, if
acpi_disabled is not set after acpi_init() has returned, this means
that ACPI is enabled. Thus, it is sufficient to check acpi_disabled
in apm_init() to prevent APM from being enabled in parallel with
ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
From the users' point of view CONFIG_PM is really only used for
making it possible to set CONFIG_SUSPEND, CONFIG_HIBERNATION,
CONFIG_PM_RUNTIME and (surprisingly enough) CONFIG_XEN_SAVE_RESTORE
(CONFIG_PM_OPP also depends on CONFIG_PM, but quite artificially).
However, both CONFIG_SUSPEND and CONFIG_HIBERNATION require platform
support (independent of CONFIG_PM) and it is not quite obvious that
CONFIG_PM has to be set for CONFIG_XEN_SAVE_RESTORE to be available.
Thus, from the users' point of view, it would be more logical to
automatically select CONFIG_PM if any of the above options depending
on it are set.
Make CONFIG_PM depend on (CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME),
which will cause it to be selected when any of CONFIG_SUSPEND,
CONFIG_HIBERNATION, CONFIG_PM_RUNTIME, CONFIG_XEN_SAVE_RESTORE is
set and will clarify its meaning.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: atomic_read() should ensure it emits a load
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
MN10300: Proper use of macros get_user() in the case of incremented pointers
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
MIPS: Jz4740: Add HAVE_CLK
MIPS: Move idle task creation to work queue
MIPS, Perf-events: Use unsigned delta for right shift in event update
MIPS, Perf-events: Work with the new callchain interface
MIPS, Perf-events: Fix event check in validate_event()
MIPS, Perf-events: Work with the new PMU interface
MIPS, Perf-events: Work with irq_work
MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
MIPS: Loongson: Fix potentially wrong string handling
MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
MIPS: Remove unused code from arch/mips/kernel/syscall.c
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
MIPS: Select R4K timer lib for all MSP platforms
MIPS: Loongson: Remove ad-hoc cmdline default
MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
MIPS: Add an unreachable return statement to satisfy buggy GCCs.
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
The SH7757's ETHER and GETHER use common MDIO pin. The MDIO pin is
selected by specific register. So this patch adds new interface in
bb_info, and when the sh_eth driver use the mdio, the register can
be changed by the function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code had hardcoded the PHY_INTERFACE_MODE_MII of phy_connect.
So some Gigabit PHYs will not behave correctly.
The patch adds the phy_interface in sh_eth_plat_data, so we can select
the phy interface.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code cannot handle the ETHER and GETHER both as same time
because the definitions of register was hardcoded.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 522d7dec(futex: Remove redundant pagefault_disable in
futex_atomic_cmpxchg_inatomic()) added a bogus comment.
/* Note that preemption is disabled by futex_atomic_cmpxchg_inatomic
* call sites. */
Bogus in two aspects:
1) pagefault_disable != preempt_disable even if the mechanism we use
is the same
2) we have a call site which deliberately does not disable pagefaults
as it wants the possible fault to be handled - though that has been
changed for consistency reasons now.
Sigh. I really should have seen that when committing the above. :(
Catched-by-and-rightfully-ranted-at-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1103141126590.2787@localhost6.localdomain6>
Cc: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.
If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer. This causes BUG() in per_cpu_trap_init.
This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leverage the commit for ARM by Will Deacon:
- 446a5a8b1e
ARM: 6205/1: perf: ensure counter delta is treated as unsigned
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2015/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Frederic Weisbecker:
- f72c1a931e
perf: Factorize callchain context handling
Store the kernel and user contexts from the generic layer instead
of archs, this gathers some repetitive code.
- 56962b4449
perf: Generalize some arch callchain code
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
- 70791ce9ba
perf: Generalize callchain_store()
callchain_store() is the same on every archs, inline it in
perf_event.h and rename it to perf_callchain_store() to avoid
any collision.
This removes repetitive code.
- c1a65932fd
perf: Drop unappropriate tests on arch callchains
Drop the TASK_RUNNING test on user tasks for callchains as
this check doesn't seem to make any sense.
Also remove the tests for !current that is not supposed to
happen and current->pid as this should be handled at the
generic level, with exclude_idle attribute.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Peter Zijlstra:
- a4eaf7f146
perf: Rework the PMU methods
Replace pmu::{enable,disable,start,stop,unthrottle} with
pmu::{add,del,start,stop}, all of which take a flags argument.
The new interface extends the capability to stop a counter while
keeping it scheduled on the PMU. We replace the throttled state with
the generic stopped state.
This also allows us to efficiently stop/start counters over certain
code paths (like IRQ handlers).
It also allows scheduling a counter without it starting, allowing for
a generic frozen state (useful for rotating stopped counters).
The stopped state is implemented in two different ways, depending on
how the architecture implemented the throttled state:
1) We disable the counter:
a) the pmu has per-counter enable bits, we flip that
b) we program a NOP event, preserving the counter state
2) We store the counter state and ignore all read/overflow events
For MIPSXX, the stopped state is implemented in the way of 1.b as above.
- 33696fc0d1
perf: Per PMU disable
Changes perf_disable() into perf_pmu_disable().
- 24cd7f54a0
perf: Reduce perf_disable() usage
Since the current perf_disable() usage is only an optimization,
remove it for now. This eases the removal of the __weak
hw_perf_enable() interface.
- b0a873ebbf
perf: Register PMU implementations
Simple registration interface for struct pmu, this provides the
infrastructure for removing all the weak functions.
- 51b0fe3954
perf: Deconstify struct pmu
sed -ie 's/const struct pmu\>/struct pmu/g' `git grep -l "const struct pmu\>"`
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Cc: ddaney@caviumnetworks.com
Patchwork: http://patchwork.linux-mips.org/patch/2012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commit by Peter Zijlstra:
- e360adbe29
irq_work: Add generic hardirq context callbacks
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
For MIPSXX, we need to call irq_work_run() at the tail of the perf IRQ
handler as described above.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com,
Patchwork: http://patchwork.linux-mips.org/patch/2011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This error was reported by cppcheck:
arch/mips/loongson/common/machtype.c:56: error: Dangerous usage of 'str' (strncpy doesn't always 0-terminate it)
If strncpy copied MACHTYPE_LEN bytes, the destination string str
was not terminated.
The patch adds one more byte to str and makes sure that this byte is
always 0.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2053/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Under some combinations of CONFIG_*, lastpfn in page_is_ram is 'set
but not used'. Mark it as __maybe_unused to quiet the warning/error.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC-4.6 can find more unused code than previous versions could.
In the case of arch/mips/math-emu/ieee754int.h, the COMPXSP and
COMPXDP macros are used in several places, but a couple of them leave
xs unused. The easiest thing to do is mark it as __maybe_unused to
quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC-4.6 can find more unused code than previous versions could.
In the case of protected_restore_fp_context{,32}, the variable tmp is
really used. Its use is tricky in that we really care about the side
effects of the __put_user() calls. So we must mark tmp with
__maybe_unused to quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson builds have an ad-hoc cmdline default of "console=ttyS0,115200
root=/dev/hda1". These settings come from a vendor; I remember builds
from Lemote branch requiring a "console=tty" override in order to get a
working console.
At least on Yeeloong, they're particularly useless: there's no external
serial port, and the IDE drive is now recognised as /dev/sda.
Signed-off-by: Robert Millan <rmh@gnu.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sysmips(MIPS_FIXADE, ...) case contains an obvious copy-and-paste
error in the handling of the TIF_LOGADE flag. Fix that
Patchwork: https://patchwork.linux-mips.org/patch/1997/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was reported that GCC-4.3.3 (with CodeSourcery extensions) fails
without this.
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trace.func should be set to the recorded ip of the mcount calling site
in the __mcount_loc section to filter the function entries configured
through the tracing/set_graph_function interface, but before, this is
set to the self_ra(the return address of mcount), which has made
set_graph_function not work as expected.
This fixes it via calculating the right recorded ip in the __mcount_loc
section and assign it to trace.func.
Reported-by: Zhiping Zhong <xzhong86@163.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2017/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
This moves the comments out of ftrace_make_nop() and cleans it. At the
same time, a macro MCOUNT_OFFSET_INSNS is defined for sharing with the
next patch.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2008/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
The old prepare_ftrace_return() for MIPS is confused and have introduced
some problem. This patch cleans up the names of the arguments, variables
and related functions.
For MIPS, the 2nd argument of prepare_ftrace_return() is not really the
'selfpc' described in ftrace-design.txt but instead it is the self
return address. This did break the compatibility of the generic
interface but really reduced one unneeded calculation for to get the
current function name, the parent return address and the self return
address are enough, no need to tranform the self return address to the
self address.
But set_graph_function of function graph tracer is an exception, it does
need the 2nd argument of prepare_ftrace_return() as 'selfpc', for it
will use 'selfpc' to match user's configuration of function graph
entries, but in reality, it doesn't need the 'selfpc' but the recorded
ip address of the mcount calling site in the __mcount_loc section. So,
the 2nd argument of prepare_ftrace_return() is not important, the real
requirement is the right recorded ip address should be calculated and
assign to trace.func, this will be fixed in the next patches.
Reported-by: Zhiping Zhong <xzhong86@163.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2007/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
The old in_module() may not work in some situations(e.g. when module &
kernel are in the same address space when CONFIG_MAPPED_KERNEL=y), The
in_kernel_space() is more generic and it is also easy to be implemented
via cloning the existing core_kernel_text(), so, replace the in_module()
with in_kernel_space().
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2005/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
This simply moves the "ip-=4" statement down to the end of the do { ...
} while (...); loop, which reduces one unneeded subtration and the
subsequent memory loading and comparison.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2006/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
The wl1271's irq line is completely controlled by the 1271 device, and
the host does not not need to pull it up.
While there's no functional effect, letting the host pull this line up is
just redundant, and wastes power.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
request_mem_region() error exit will leak ioremapped memory. Fix this
by moving the ioremap() after request_mem_region(), which is the proper
order to do this anyway.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adapts the register offsets used to read the CPU DIE ID registers
when run on 44XX so they match what is in the OMAP4430 Reference Manual
page 269
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove duplicate mux modes to make the binary smaller:
text data bss dec hex filename
9378 24472 0 33850 843a mux44xx.o
9378 19104 0 28482 6f42 mux44xx.o
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently IOVMM driver sets IOVMF_DA_FIXED/IOVMF_DA_ANON flags according
to input 'da' address when mapping memory:
da == 0: IOVMF_DA_ANON
da != 0: IOVMF_DA_FIXED
It prevents IOMMU to map first page with fixed 'da'. To avoid such
issue, IOVMM will not automatically set IOVMF_DA_FIXED. It should now
come from the user throught 'flags' parameter when mapping memory.
As IOVMF_DA_ANON and IOVMF_DA_FIXED are mutually exclusive, IOVMF_DA_ANON
can be removed. The driver will now check internally if IOVMF_DA_FIXED
is set or not.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit c7f4ab26e3 allowed mapping the NULL
address if da_start==0, which would then not get unmapped. Disallow
this again if IOVMF_DA_ANON is set. And spell variable 'alignment'
correctly.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Removal of driver_pages (I do not have seen any references to it).
Signed-off-by: Daniel Kiper <dkiper@net-space.pl>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If there is no proper PFN value in the M2P for the MFN
(so we get 0xFFFFF.. or 0x55555, or 0x0), we should
consult the M2P override to see if there is an entry for this.
[Note: we also consult the M2P override if the MFN
is past our machine_to_phys size].
We consult the P2M with the PFN. In case the returned
MFN is one of the special values: 0xFFF.., 0x5555
(which signify that the MFN can be either "missing" or it
belongs to DOMID_IO) or the p2m(m2p(mfn)) != mfn, we check
the M2P override. If we fail the M2P override check, we reset
the PFN value to INVALID_P2M_ENTRY.
Next we try to find the MFN in the P2M using the MFN
value (not the PFN value) and if found, we know
that this MFN is an identity value and return it as so.
Otherwise we have exhausted all the posibilities and we
return the PFN, which at this stage can either be a real
PFN value found in the machine_to_phys.. array, or
INVALID_P2M_ENTRY value.
[v1: Added Review-by tag]
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
.. beyound what we think is the end of memory. However there might
be more System RAM - but assigned to a guest. Hence jump to the
M2P override check and consult.
[v1: Added Review-by tag]
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Only enabled if XEN_DEBUG is enabled. We print a warning
when:
pfn_to_mfn(pfn) == pfn, but no VM_IO (_PAGE_IOMAP) flag set
(and pfn is an identity mapped pfn)
pfn_to_mfn(pfn) != pfn, and VM_IO flag is set.
(ditto, pfn is an identity mapped pfn)
[v2: Make it dependent on CONFIG_XEN_DEBUG instead of ..DEBUG_FS]
[v3: Fix compiler warning]
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We walk over the whole P2M tree and construct a simplified view of
which PFN regions belong to what level and what type they are.
Only enabled if CONFIG_XEN_DEBUG_FS is set.
[v2: UNKN->UNKNOWN, use uninitialized_var]
[v3: Rebased on top of mmu->p2m code split]
[v4: Fixed the else if]
Reviewed-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We walk the E820 region and start at 0 (for PV guests we start
at ISA_END_ADDRESS) and skip any E820 RAM regions. For all other
regions and as well the gaps we set them to be identity mappings.
The reasons we do not want to set the identity mapping from 0->
ISA_END_ADDRESS when running as PV is b/c that the kernel would
try to read DMI information and fail (no permissions to read that).
There is a lot of gnarly code to deal with that weird region so
we won't try to do a cleanup in this patch.
This code ends up calling 'set_phys_to_identity' with the start
and end PFN of the the E820 that are non-RAM or have gaps.
On 99% of machines that means one big region right underneath the
4GB mark. Usually starts at 0xc0000 (or 0x80000) and goes to
0x100000.
[v2: Fix for E820 crossing 1MB region and clamp the start]
[v3: Squshed in code that does this over ranges]
[v4: Moved the comment to the correct spot]
[v5: Use the "raw" E820 from the hypervisor]
[v6: Added Review-by tag]
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The initial bootup code uses set_phys_to_machine quite a lot, and after
bootup it would be used by the balloon driver. The balloon driver does have
mutex lock so this should not be necessary - but just in case, add
a WARN_ON if we do hit this scenario. If we do fail this, it is OK
to continue as there is a backup mechanism (VM_IO) that can bypass
the P2M and still set the _PAGE_IOMAP flags.
[v2: Change from WARN to BUG_ON]
[v3: Rebased on top of xen->p2m code split]
[v4: Change from BUG_ON to WARN]
Reviewed-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we find that the PFN is within the P2M as an identity
PFN make sure to tack on the _PAGE_IOMAP flag.
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Our P2M tree structure is a three-level. On the leaf nodes
we set the Machine Frame Number (MFN) of the PFN. What this means
is that when one does: pfn_to_mfn(pfn), which is used when creating
PTE entries, you get the real MFN of the hardware. When Xen sets
up a guest it initially populates a array which has descending
(or ascending) MFN values, as so:
idx: 0, 1, 2
[0x290F, 0x290E, 0x290D, ..]
so pfn_to_mfn(2)==0x290D. If you start, restart many guests that list
starts looking quite random.
We graft this structure on our P2M tree structure and stick in
those MFN in the leafs. But for all other leaf entries, or for the top
root, or middle one, for which there is a void entry, we assume it is
"missing". So
pfn_to_mfn(0xc0000)=INVALID_P2M_ENTRY.
We add the possibility of setting 1-1 mappings on certain regions, so
that:
pfn_to_mfn(0xc0000)=0xc0000
The benefit of this is, that we can assume for non-RAM regions (think
PCI BARs, or ACPI spaces), we can create mappings easily b/c we
get the PFN value to match the MFN.
For this to work efficiently we introduce one new page p2m_identity and
allocate (via reserved_brk) any other pages we need to cover the sides
(1GB or 4MB boundary violations). All entries in p2m_identity are set to
INVALID_P2M_ENTRY type (Xen toolstack only recognizes that and MFNs,
no other fancy value).
On lookup we spot that the entry points to p2m_identity and return the identity
value instead of dereferencing and returning INVALID_P2M_ENTRY. If the entry
points to an allocated page, we just proceed as before and return the PFN.
If the PFN has IDENTITY_FRAME_BIT set we unmask that in appropriate functions
(pfn_to_mfn).
The reason for having the IDENTITY_FRAME_BIT instead of just returning the
PFN is that we could find ourselves where pfn_to_mfn(pfn)==pfn for a
non-identity pfn. To protect ourselves against we elect to set (and get) the
IDENTITY_FRAME_BIT on all identity mapped PFNs.
This simplistic diagram is used to explain the more subtle piece of code.
There is also a digram of the P2M at the end that can help.
Imagine your E820 looking as so:
1GB 2GB
/-------------------+---------\/----\ /----------\ /---+-----\
| System RAM | Sys RAM ||ACPI| | reserved | | Sys RAM |
\-------------------+---------/\----/ \----------/ \---+-----/
^- 1029MB ^- 2001MB
[1029MB = 263424 (0x40500), 2001MB = 512256 (0x7D100), 2048MB = 524288 (0x80000)]
And dom0_mem=max:3GB,1GB is passed in to the guest, meaning memory past 1GB
is actually not present (would have to kick the balloon driver to put it in).
When we are told to set the PFNs for identity mapping (see patch: "xen/setup:
Set identity mapping for non-RAM E820 and E820 gaps.") we pass in the start
of the PFN and the end PFN (263424 and 512256 respectively). The first step is
to reserve_brk a top leaf page if the p2m[1] is missing. The top leaf page
covers 512^2 of page estate (1GB) and in case the start or end PFN is not
aligned on 512^2*PAGE_SIZE (1GB) we loop on aligned 1GB PFNs from start pfn to
end pfn. We reserve_brk top leaf pages if they are missing (means they point
to p2m_mid_missing).
With the E820 example above, 263424 is not 1GB aligned so we allocate a
reserve_brk page which will cover the PFNs estate from 0x40000 to 0x80000.
Each entry in the allocate page is "missing" (points to p2m_missing).
Next stage is to determine if we need to do a more granular boundary check
on the 4MB (or 2MB depending on architecture) off the start and end pfn's.
We check if the start pfn and end pfn violate that boundary check, and if
so reserve_brk a middle (p2m[x][y]) leaf page. This way we have a much finer
granularity of setting which PFNs are missing and which ones are identity.
In our example 263424 and 512256 both fail the check so we reserve_brk two
pages. Populate them with INVALID_P2M_ENTRY (so they both have "missing" values)
and assign them to p2m[1][2] and p2m[1][488] respectively.
At this point we would at minimum reserve_brk one page, but could be up to
three. Each call to set_phys_range_identity has at maximum a three page
cost. If we were to query the P2M at this stage, all those entries from
start PFN through end PFN (so 1029MB -> 2001MB) would return INVALID_P2M_ENTRY
("missing").
The next step is to walk from the start pfn to the end pfn setting
the IDENTITY_FRAME_BIT on each PFN. This is done in 'set_phys_range_identity'.
If we find that the middle leaf is pointing to p2m_missing we can swap it over
to p2m_identity - this way covering 4MB (or 2MB) PFN space. At this point we
do not need to worry about boundary aligment (so no need to reserve_brk a middle
page, figure out which PFNs are "missing" and which ones are identity), as that
has been done earlier. If we find that the middle leaf is not occupied by
p2m_identity or p2m_missing, we dereference that page (which covers
512 PFNs) and set the appropriate PFN with IDENTITY_FRAME_BIT. In our example
263424 and 512256 end up there, and we set from p2m[1][2][256->511] and
p2m[1][488][0->256] with IDENTITY_FRAME_BIT set.
All other regions that are void (or not filled) either point to p2m_missing
(considered missing) or have the default value of INVALID_P2M_ENTRY (also
considered missing). In our case, p2m[1][2][0->255] and p2m[1][488][257->511]
contain the INVALID_P2M_ENTRY value and are considered "missing."
This is what the p2m ends up looking (for the E820 above) with this
fabulous drawing:
p2m /--------------\
/-----\ | &mfn_list[0],| /-----------------\
| 0 |------>| &mfn_list[1],| /---------------\ | ~0, ~0, .. |
|-----| | ..., ~0, ~0 | | ~0, ~0, [x]---+----->| IDENTITY [@256] |
| 1 |---\ \--------------/ | [p2m_identity]+\ | IDENTITY [@257] |
|-----| \ | [p2m_identity]+\\ | .... |
| 2 |--\ \-------------------->| ... | \\ \----------------/
|-----| \ \---------------/ \\
| 3 |\ \ \\ p2m_identity
|-----| \ \-------------------->/---------------\ /-----------------\
| .. +->+ | [p2m_identity]+-->| ~0, ~0, ~0, ... |
\-----/ / | [p2m_identity]+-->| ..., ~0 |
/ /---------------\ | .... | \-----------------/
/ | IDENTITY[@0] | /-+-[x], ~0, ~0.. |
/ | IDENTITY[@256]|<----/ \---------------/
/ | ~0, ~0, .... |
| \---------------/
|
p2m_missing p2m_missing
/------------------\ /------------\
| [p2m_mid_missing]+---->| ~0, ~0, ~0 |
| [p2m_mid_missing]+---->| ..., ~0 |
\------------------/ \------------/
where ~0 is INVALID_P2M_ENTRY. IDENTITY is (PFN | IDENTITY_BIT)
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
[v5: Changed code to use ranges, added ASCII art]
[v6: Rebased on top of xen->p2m code split]
[v4: Squished patches in just this one]
[v7: Added RESERVE_BRK for potentially allocated pages]
[v8: Fixed alignment problem]
[v9: Changed 1<<3X to 1<<BITS_PER_LONG-X]
[v10: Copied git commit description in the p2m code + Add Review tag]
[v11: Title had '2-1' - should be '1-1' mapping]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
atomic_read() needs to ensure that it emits a load (which it can do by using
ACCESS_ONCE()).
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
The invalidate-only versions of flush_icache_*range() are trying sending the
SMP_ICACHE_INV_FLUSH_RANGE IPI command in SMP kernels when they should be
sending SMP_ICACHE_INV_RANGE as the former does not exist.
Signed-off-by: David Howells <dhowells@redhat.com>
Using __get_user_check(x, ptr++, size) leads to double increment of pointer.
This macro uses the macro get_user directly, which itself is used in this way
(get_user(x, ptr++)) in some functions of the kernel. The patch fixes the
error.
Reported-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David Howells <dhowells@redhat.com>
Setting the pci ops on subsys initcall unconditionally will break
multi platform kernels on anything except ce4100.
Use x86_init.pci.init ops to call this only on real ce4100 platforms.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: sodaville@linutronix.de
LKML-Reference: <20110314093340.GA21026@www.tglx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
New helpers: user_statfs() and fd_statfs(), taking userland pathname and
descriptor resp. and filling struct kstatfs. Syscalls of statfs family
(native, compat and foreign - osf and hpux on alpha and parisc resp.)
switched to those. Removes some boilerplate code, simplifies cleanup
on errors...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
new function: file_open_root(dentry, mnt, name, flags) opens the file
vfs_path_lookup would arrive to.
Note that name can be empty; in that case the usual requirement that
dentry should be a directory is lifted.
open-coded equivalents switched to it, may_open() got down exactly
one caller and became static.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
all remaining callers pass LOOKUP_PARENT to it, so
flags argument can die; renamed to kern_path_parent()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All platform data has to be made conditional on
as to avoid cluttering the code with other #ifdef:s.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The HREFv60 variant of the MOP500 family of boards remove the
external GPIO expander and route these pins back to some of the
readily available internal GPIO pins instead.
Based on a patch by Bibek Basu <bibek.basu@stericsson.com> for
an internal kernel version.
Cc: Bibek Basu <bibek.basu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This will centralize all GPIO pin muxing for the different boards
in the MOP500 family to a single file. It also kills off the
deprecated support for the ED (Early Drop) ASIC, this should
never be spotted in the open and ST-Ericsson have internally
deprecated this hardware.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Rebasing and kill old ASIC support]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Split off pin definitions for the MOP500 board family to its
own file.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The compiler warns that [rf]wimsc may be used uninitialized in
this function - the warning is actually false since the uses are
in identical if()-clauses, but it can't hurt very much to read
out the values to be modified early anyway and rid the warning.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NOMADIK_GPIO_PM config option is disabled by default, not user visible,
and never selected by any other option: the code is therefore unused. The
GPIO registers need not be saved and restored since their values are
preserved when vAPE (on DB8500) is powered down.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes a bug when setting SLPM register for DB8500.
When calling__nmk_gpio_set_slpm(...) offset to GPIO is now used
instead of the GPIO number itself.
Signed-off-by: Rikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.
This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Coverity found that we were checking an unsigned variable for
>= zero. Type it correctly so that the check works as intended.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Suspend/resume didn't take care of pull-up and pull-down
settings and writing back the DAT register at resume can
change pull up/down settings, depending on pin input value.
Output values are now also restored.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIOs wake up the system from sleep mode, the normal GPIO interrupt
handler does not hit and the normal interrupt status register does not
contain the status. Instead the secondary GPIO handler does, and the
interrupt status needs to be retrieved from the wakeup status saved by
the suspend/resume code.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This will configure the platform data for the PL011, PL022
and PL180 (derivate) PrimeCells found in the Ux500 to use DMA
with the generic DMA engine for DMA40.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This will configure the platform data for the PL180, PL011 and
PL022 PrimeCells found in the U300 to use DMA with the generic
PrimeCell DMA engine for COH 901 318.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmci driver can handle a GPIO pin for card detect, using
IRQs and all just fine, so switch to using that. Delete the
old bogus input device hack, if userspace need to detect
MMC cards it should use udev like everyone else.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- DMA tx and rx maps for usb channels are set to be configured at
runtime
- MUSB is enabled with soc specific base address, irq and dma
configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- DMA tx and rx maps for usb channels are set to be configured at
runtime
- GPIO configurations for usb are added
- MUSB is enabled with soc specific base address, irq and dma
configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MUSB driver has been updated to separate out BSP layer
from its generic parts, as separate driver. This patch
configures the clock with the new platform driver name.
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USB resources and DMA40 configurations are dynamically with
the data provided in ux500_add_usb() call. Though only DMA40
configurations differ between U8500 and U5500 (USB resource
are common between them).
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The levelshifter pins were set to inverted values, fix this up.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock speed for the SD/MMC clock was incorrect, rectify it.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Proximity sensor is managed as an input event (SW_PROXIMITY).
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
[Named GPIO pin]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The U8500 UIB contains a Synaptics RMI touchpanel and
a matrix keyboard via the TC35893 port expander device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ST-UIB contains a matrix keypad interfaced with the
STMPE1601 port expander and a ROHM BU2101 touch panel.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include ab8500 regulators for DB8500 SoC by default
and fix build issues
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
[Small fixup for changed boardfiles]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Try to make the regulators a little bit more useful by adding some
of the most basic consumers we're going to have in the end.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the PMU resources necessary to get perf working with
the DB5500 ASIC.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The caller of ioapic_register_intr() has a pointer to the irq_cfg for
the irq already. Hand it in to avoid a full lookup.
In msi_compose_msg() the pointer to irq_cfg is already available. No
need to look it up again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the functions which take irq_data. We already have a pointer to
irq_data. That avoids a sparse irq lookup in move_*_irq.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the state information in irq_data. That avoids a radix-tree lookup
from apic_ack_level() and simplifies setup_ioapic_dest().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
genirq is switching to a consistent name space for the irq related
functions. Convert x86. Conversion was done with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The distance transforming in numa_emulation() used to call
numa_set_distance() for all MAX_NUMNODES * MAX_NUMNODES node
combinations regardless of which are enabled. As numa_set_distance()
ignores all out-of-bound distance settings, this doesn't cause any
problem other than looping unnecessarily many times during boot.
However, as MAX_NUMNODES * MAX_NUMNODES can be pretty high, update the
code such that it iterates through only the enabled combinations.
Yinghai Lu identified the issue and provided an initial patch to
address the issue; however, the patch was incorrect in that it didn't
build emulated distance table when there's no physical distance table
and unnecessarily complex.
http://thread.gmane.org/gmane.linux.kernel/1107986/focus=1107988
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The latest binutils (2.21.0.20110302/Ubuntu) breaks the build
yet another time, under CONFIG_XEN=y due to a .size directive that
refers to a slightly differently named (hence, to the now very
strict and unforgiving assembler, non-existent) symbol.
[ mingo:
This unnecessary build breakage caused by new binutils
version 2.21 gets escallated back several kernel releases spanning
several years of Linux history, affecting over 130,000 upstream
kernel commits (!), on CONFIG_XEN=y 64-bit kernels (i.e. essentially
affecting all major Linux distro kernel configs).
Git annotate tells us that this slight debug symbol code mismatch
bug has been introduced in 2008 in commit 3d75e1b8:
3d75e1b8 (Jeremy Fitzhardinge 2008-07-08 15:06:49 -0700 1231) ENTRY(xen_do_hypervisor_callback) # do_hypervisor_callback(struct *pt_regs)
The 'bug' is just a slight assymetry in ENTRY()/END()
debug-symbols sequences, with lots of assembly code between the
ENTRY() and the END():
ENTRY(xen_do_hypervisor_callback) # do_hypervisor_callback(struct *pt_regs)
...
END(do_hypervisor_callback)
Human reviewers almost never catch such small mismatches, and binutils
never even warned about it either.
This new binutils version thus breaks the Xen build on all upstream kernels
since v2.6.27, out of the blue.
This makes a straightforward Git bisection of all 64-bit Xen-enabled kernels
impossible on such binutils, for a bisection window of over hundred
thousand historic commits. (!)
This is a major fail on the side of binutils and binutils needs to turn
this show-stopper build failure into a warning ASAP. ]
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kees Cook <kees.cook@canonical.com>
LKML-Reference: <1299877178-26063-1-git-send-email-heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch updates HRT driver for supporting PM.
The resume function of PWM4 timer which is used clocksource is needed
when kernel is resuming for restarting.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support suspend to ram for EXYNOS4210.
As a note, this includes function of outer cache flush
because it is used before entering PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions of PMU and CMU registers for EXYNOS4 PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for fourth FIMC platform device definition and define
resources for FIMC modules on EXYNOS4 machines.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates s5pv210_defconfig and s5p64x0_defconfig for
HRT support and CONFIG_S5P_HRT is used for its configuration.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HRT for machines of S5P64X0 and S5PV210.
Basically, PWM Timer3 is used for clockevent and PWM Timer4 is
used for clocksource. Since PWM Timer3 is used for other purpose,
PWM Timer2 is used on SMDKV210.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HR-Timer(High Resolution Timer) and dynamic
tick system for S5P SoCs. There are many clock sources for HR-Timer
on S5P SoCs. The PWM timer, RTC, System Timer, and MCT can be used
for clock source.
This patch can only support PWM timer for clock source of S5P64X0
and S5PV210.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add macro for defining static pins in the board file.
We can now start implementing pin multiplexing in the platform init
code for devices that call omap_hwmod_mux_init. Currently that is
only implemented for serial.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids going through the list unnecessarily when
idling devices for runtime PM.
Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMAX is an internal name for the module which is
known as PRUSS in TI public documentation. This patch just
gets the code in sync with TI documentation.
Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 75e2ea643f (davinci: DA850/OMAP-L138 EVM
expander setup and UI card detection) introduced a useless variable: it's
always set to 1 before it's checked in da850_evm_setup_nor_nand()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the on-board SPI flash device to the
DA850/OMAP-L138/AM18x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da850_evm_spi1_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da850evm_init_spi1 to devices-da8xx.c]
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add IO resource structures, platform data, and a registration
routine in order to support spi device on DA850/OMAP-L138/AM18x
and DA830/OMAP-L137/AM17x platforms.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add spi clock information for da850.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The spi driver name called out for the da830 spi clock list is not correct,
fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Extract magic numbers from DMA resource initializers to #defines.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The DA830_edma_ch enum set is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
If we have a guest that asked for:
memory=1024
maxmem=2048
Which means we want 1GB now, and create pagetables so that we can expand
up to 2GB, we would have this E820 layout:
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved)
[ 0.000000] Xen: 0000000000100000 - 0000000080800000 (usable)
Due to patch: "xen/setup: Inhibit resource API from using System RAM E820 gaps as PCI mem gaps."
we would mark the memory past the 1GB mark as unusuable resulting in:
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved)
[ 0.000000] Xen: 0000000000100000 - 0000000040000000 (usable)
[ 0.000000] Xen: 0000000040000000 - 0000000080800000 (unusable)
which meant that we could not balloon up anymore. We could
balloon the guest down. The fix is to run the code introduced
by the above mentioned patch only for the initial domain.
We will have to revisit this once we start introducing a modified
E820 for PCI passthrough so that we can utilize the P2M identity code.
We also fix an overflow by having UL instead of ULL on 32-bit machines.
[v2: Ian pointed to the overflow issue]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The patch adds the new power management trace points for
the OMAP architecture.
The trace points are for:
- default idle handler. Since the cpuidle framework is
instrumented in the generic way there is no need to
add trace points in the OMAP specific cpuidle handler;
- SoC clocks changes (enable, disable, set_rate),
- power domain states: the desired target state and -if different-
the actually hit state.
Because of the generic nature of the changes, OMAP3 and OMAP4 are supported.
Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This Patch adds OPP enteries for IVA in OMAP4 OPP Table
Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz.
Enable them in OPP Table. For small minority of boards which use
OMAP4430-800 MHz device OPP 1GHz is not supported,
OPP 1GHz should be disabled from board file.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since all voltage data is now centralized in oppxxx_data.c, we can replace
the values in the opp table with the macros used for voltage values.
This will avoid opp table and voltage layer having conflicting values.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use nand_scan_ident to unify the need of mtd member initilization
for both normal detection and keep configuration method.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New variable skip_initial_unlocking is added to the omap_onenand_platform_data.
This is used to inform the onenand driver to skip onenand unlocking when it
is initialized.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As MTD_CONCAT support is becoming an integral part of MTD core,
there is no need for it's special treatment. So stop checking for
MTD_CONCAT availability.
Acked by Jesper Nilsson <jesper.nilsson@axis.com> for merging this
via the MTD tree.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the standard push buttons available on
Overo expansion boards.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the standard LEDs on the Overo COM and expansion boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The ads7846 driver now requires a regulator. This patch adds the
necessary regulator to the overo board file. Without it, the
following error occurs (and the touchscreen will not function):
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds DSS2 support for DVI, S-video, the 480x272 Samsung
LTE430WQ-F0C panel, and the 320x240 LG.Philips LB035Q02 panel.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce functions which request and release VC's. This will be used in panel
drivers in their probes.
omap_dsi_request_vc() takes in the pointer to the omap_dss_device, the VC_ID
parameter which goes into the header of the DSI packets, and returns a Virtual
channel number (or virtual channel register set) which it can use.
omap_dsi_set_vc_id() takes the omap_dss_device pointer, the Virtual Channel
number and the VC_ID that needs to be set for the specifed Virtual Channel.
omap_dsi_release_vc() takes the omap_dss_device pointer and the Virtual Channel
number that needs to be made free.
Initialisation of VC parameters is done in dsi_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI PLL output clock names have been made more generic. The clock name
describes what the source of the clock and what clock is used for. Some of
DSI PLL parameters like dividers and DSI PLL source have also been made more
generic.
dsi1_pll_fclk and dsi2_pll_fclk have been changed as dsi_pll_hsdiv_dispc_clk
and dsi_pll_hsdiv_dsi_clk respectively. Also, the hsdividers are now named
regm_dispc and regm_dsi instead of regm3 and regm4.
Functions and macros named on the basis of these clock names have also been
made generic.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Provide a function in pdata to allow dss submodules to check if a given
clock is available on a platform as an optional clock.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
(based on implementation from Senthil)
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enabling all the display interface options to be built as module
And enabling all the display panels to be built as modules.
Signed-off-by: Samreen <samreen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.
On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.
On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.
Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.
Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.
The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS code uses ick as one of the clocks in clk_get/clk_put. OMAP4 clock database
doesn't have ick for DSS, so adding ick as dummy clock.
This is needed for backward compatibility with OMAP2/3.
Once pm_runtime* APIs get introduced in DSS, this will be revisited.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, clock database has <dev, clock-name> tuples for DSS2. Because of
this, the clock names are different across different OMAP platforms.
This patch aligns the DSS2 clock names and roles across OMAP 2420, 2430, 3xxx,
44xx platforms in the clock databases, hwmod databases for opt-clocks, and DSS
clock handling.
This ensures that clk_get/put/enable/disable APIs in DSS can use uniform role
names.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DSI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, vdds_dsi regulator handling is copied to dsi.c, since vdds_dsi regulator is
needed by dpi_init() too. Board files are updated accordingly to add 2 instances of
vdds_dsi regulator.
DSI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, venc_vdda_dac reading is moved to venc.c.
VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All clock management is moved to dss platform driver. clk_get/put APIs use
dss device instead of core platform device.
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So the device name is changed from omapdss to omapdss_dss in 2420, 2430,
3xxx clock database files. Now the core driver "omapdss" only takes care
of panel registration with the custom bus.
core driver also uses the clk_enable() / clk_disable() APIs exposed by DSS for
clock management.
DSS driver would do clock management of clocks needed by DISPC, RFBI, DSI, VENC
TODO: The clock content would be adapted to omap_hwmod in a seperate series.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ASoC audio for mini2440 platform in current kenrel doesn't work.
First problem is samsung_asoc_dma device is missing in initialization.
Next problem is with codec. Codec is initialized but never probed
because no platform_device exist for codec driver. It leads to errors
during codec binding to asoc dai. Next problem was platform data which
was passed from board to asoc main driver but not passed to codec when
called codec_soc_probe().
Following patch should fix issues. But not sure if in correct way.
Please review.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
prototypes to use u32 types for the futex as this is the data type the
futex core code uses all over the place.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311025058.GD26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cmpxchg_futex_value_locked API was funny in that it returned either
the original, user-exposed futex value OR an error code such as -EFAULT.
This was confusing at best, and could be a source of livelocks in places
that retry the cmpxchg_futex_value_locked after trying to fix the issue
by running fault_in_user_writeable().
This change makes the cmpxchg_futex_value_locked API more similar to the
get_futex_value_locked one, returning an error code and updating the
original value through a reference argument.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile]
Acked-by: Tony Luck <tony.luck@intel.com> [ia64]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Simek <monstr@monstr.eu> [microblaze]
Acked-by: David Howells <dhowells@redhat.com> [frv]
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024851.GC26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kernel/futex.c disables page faults before calling
futex_atomic_cmpxchg_inatomic(), so there is no need to do it again
within that function.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024731.GB26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are two dividers used to derive bus clock from system clock:
system clock is divided by SCKDIV+1, then by BCKDIV+1. SCKDIV divider
has been ignored up to now, which is no problem as long as it is 0.
Take SCKDIV into account for bus clock calculation.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove double definition of ACLKUSBH, change parameter name in
root_clk_disable, as there is no reason to have a different name than
in root_clk_enable.
No functional change.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no reason why in case of PLL2 the configuration register
should be read twice, while for PLL0/1 using the value previously read
is used. Do the same for PLL2.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The calculation of the best divider value for a requested clock rate
always returned a value that was slightly too large. It was also not
protected against possible divisions by zero.
Request for very low, but non zero rates would cause the ACLK divisor
field to overflow. Catch this situation by using the maximum value.
The internal function aclk_set_rate() calculates the correct divider
value, but doesn't write it back to the register. Add the write back.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The evaluation board is driven with 1.2V core voltage, so system clock
must not exceed 192 MHz, bus clock must not exceed 110 MHz. Choose
appropriate values and set DTCMWAIT accordingly. Adapt UART setting to
avoid console log interruption and wait for the specified locking time
of 300us to pass.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If NAND is enabled we better have the include around.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch moves some functions and variables into init
sections, makes a function static and removes some lines of
cruft.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <1299826956-8607-2-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The extra tsc_sync.o goal definition is superflous.
CONFIG_X86_64_SMP depends on CONFIG_SMP
and tsc_sync.o is already in the definition of CONFIG_SMP.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <1299826956-8607-1-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add common code for MIPI-CSIS and MIPI-DSIM drivers to support
their corresponding D-PHY's enable and reset control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Extend MIPI-CSIS driver's platform data structure with a callback
for D-PHY enable and reset control. Also add a flag indicating
whether the external MIPI-CSI (VDD18_MIPI) power supply should
be managed in the driver through the "vdd" power supply. On some
boards this regulator may be a fixed voltage regulator without
an inhibit function.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add functions for configuration of the parallel camera
bus pins on S5PV210 and Exynos4 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The HW superwised smart idle for wdtimer in OMAP3 prevents
CORE power domain idle transitions. Disable it by swithing
to SW supervised transitions.
This could be a hardware bug in the OMAP3 wdtimer2 block.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
This is a first pass at reorganizing mach-omap2/voltage.c:
- Separate almost all of the data from the code of mach-omap2/voltage.c.
The code remains in mach-omap2/voltage.c. The data goes into one
of several places, depending on what type of data it is:
- Silicon process/validation data: mach-omap2/opp*_data.c
- VC (Voltage Controller) data: mach-omap2/vc*_data.c
- VP (Voltage Processor) data: mach-omap2/vp*_data.c
- Voltage domain data: mach-omap2/voltagedomains*_data.c
The ultimate goal is for all this data to be autogenerated, the same
way we autogenerate the rest of our data.
- Separate VC and VP common data from VDD-specific VC and VP data.
- Separate common voltage.c code from SoC-specific code; reuse common code.
- Reorganize structures to avoid unnecessary memory loss due to unpacked
fields.
There is much left to be done. VC code and VP code should be separated out
into vc*.c and vp*.c files. Many fields in the existing structures are
superfluous, and should be removed. Some code in voltage.c seems to be
duplicated; that code should be moved into functions of its own. Proper
voltage domain code should be created, as was done with the powerdomain
and clockdomains, and powerdomains should reference voltagedomains.
Thanks to Shweta Gulati <shweta.gulati@ti.com> for comments. Thanks
to Rajendra Nayak <rnayak@ti.com> for finding and fixing some bugs
that prevented OMAP4 from booting:
https://patchwork.kernel.org/patch/587311/
His patch has been folded into this one to avoid breaking OMAP4
between patches. Thanks also to Kevin Hilman <khilman@ti.com> for
finding and fixing a compile problem when !CONFIG_PM:
http://www.spinics.net/lists/arm-kernel/msg118067.html
His patch has also been folded into this one to avoid breaking
!CONFIG_PM builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shweta Gulati <shweta.gulati@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
- enable SPI bus, MTD, MMCIF, SD, USB host, and USB storage.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
C0 is known as "busy", "not idle" state.
X86 "busy polling" state also got renamed from C0
to "POLL" recently.
Let's stay consistent with naming to avoid confusions.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On upcoming hardware, we have a PCI adapter with two functions, one of
which uses MSI and the other uses MSI-X. This adapter, when MSI is
disabled using the "old" firmware interface (RTAS_CHANGE_FN), still
signals an MSI-X interrupt and triggers an EEH. We are working with the
vendor to ensure that the hardware is not at fault, but if we use the
"new" interface (RTAS_CHANGE_MSI_FN) to disable MSI, we also
automatically disable MSI-X and the adapter does not appear to signal
any stray MSI-X interrupt.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Multi-Core Timer(MCT) of EXYNOS4 is designed for implementing
clock source timer and clock event timers. This patch implements
1 clock source timer with 64 bit free running counter of MCT and
2 clock event timers with two of 31-bit tick counters.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds IRQ_MCT_G0 to irq map. IRQ_MCT_G0 is an interrupt
of MCT comparator and used for kernel global timer.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The MCT(Multi-Core Timer) is used for implementing kernel timers
for EXYNOS4210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The first issue fixed in this patch is that pending rwlock write locks
could lock out new readers; this could cause a deadlock if a read lock was
held on cpu 1, a write lock was then attempted on cpu 2 and was pending,
and cpu 1 was interrupted and attempted to re-acquire a read lock.
The write lock code was modified to not lock out new readers.
The second issue fixed is that there was a narrow race window where a tns
instruction had been issued (setting the lock value to "1") and the store
instruction to reset the lock value correctly had not yet been issued.
In this case, if an interrupt occurred and the same cpu then tried to
manipulate the lock, it would find the lock value set to "1" and spin
forever, assuming some other cpu was partway through updating it. The fix
is to enforce an interrupt critical section around the tns/store pair.
In addition, this change now arranges to always validate that after
a readlock we have not wrapped around the count of readers, which
is only eight bits.
Since these changes make the rwlock "fast path" code heavier weight,
I decided to move all the rwlock code all out of line, leaving only the
conventional spinlock code with fastpath inlines. Since the read_lock
and read_trylock implementations ended up very similar, I just expressed
read_lock in terms of read_trylock.
As part of this change I also eliminate support for the now-obsolete
tns_atomic mode.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Initialize the broadcast assist unit base destination node id properly
x86, numa: Fix numa_emulation code with memory-less node0
x86, build: Make sure mkpiggy fails on read error
On the newer ARM processors like CortexA8, CortexA9, the caches can be
speculatively loaded while they are getting flushed.
Clear the SCTLR C bit to prevent further data cache allocation as
part of cache clean routine
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current code saves few un-necessary registers which are read-only or
write-only, unused CP15 registers.
Remove them and keep only necessary CP15 registers part of
low power context save/restore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When L1 cache is suppose to be lost, it needs to be cleaned before
entrering to the low power mode.
While at this, also fix few comments and remove un-necessary
clean_l2 lable.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When we're interrupted on the secure side, we should just issue
another smc instruction again instead of replaying the arguments
to smc. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Assign the registers used in the inline assembly immediately
before the inline assembly block. This ensures the compiler
doesn't optimize away dead register assignments when it
shouldn't.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Brown <davidb@codeaurora.org>
We don't want the compiler to remove these asm statements or
reorder them in any way. Mark them as volatile to be sure.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Following the example set by xen_allocate_pirq_msi and
xen_bind_pirq_msi_to_irq:
xen_allocate_pirq becomes xen_allocate_pirq_gsi and now only allocates
a pirq number and does not bind it.
xen_map_pirq_gsi becomes xen_bind_pirq_gsi_to_irq and binds an
existing pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The function name does not distinguish it from xen_allocate_pirq_msi
(which operates on domU and pvhvm domains rather than dom0).
Hoist domain 0 specific functionality up into the only caller leaving
functionality common to all guest types in xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Makes the tail end of this function look even more like
xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Split the binding aspect of xen_allocate_pirq_msi out into a new
xen_bind_pirq_to_irq function.
In xen_hvm_setup_msi_irq when allocating a pirq write the MSI message
to signal the PIRQ as soon as the pirq is obtained. There is no way to
free the pirq back so if the subsequent binding to an IRQ fails we
want to ensure that we will reuse the PIRQ next time rather than leak
it.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
apic_register_gsi_xen_hvm is a tiny wrapper around
xen_hvm_register_pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
consistent with other similar functions.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
All callers pass this flag so it is pointless.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fixes:
CC arch/x86/pci/xen.o
arch/x86/pci/xen.c:183: warning: 'xen_initdom_setup_msi_irqs' defined but not used
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* stable/pcifront-fixes:
pci/xen: When free-ing MSI-X/MSI irq->desc also use generic code.
pci/xen: Cleanup: convert int** to int[]
pci/xen: Use xen_allocate_pirq_msi instead of xen_allocate_pirq
xen-pcifront: Sanity check the MSI/MSI-X values
xen-pcifront: don't use flush_scheduled_work()
* stable/irq.rework:
xen/irq: Cleanup up the pirq_to_irq for DomU PV PCI passthrough guests as well.
xen: Use IRQF_FORCE_RESUME
xen/timer: Missing IRQF_NO_SUSPEND in timer code broke suspend.
xen: Fix compile error introduced by "switch to new irq_chip functions"
xen: Switch to new irq_chip functions
xen: Remove stale irq_chip.end
xen: events: do not free legacy IRQs
xen: events: allocate GSIs and dynamic IRQs from separate IRQ ranges.
xen: events: add xen_allocate_irq_{dynamic, gsi} and xen_free_irq
xen:events: move find_unbound_irq inside CONFIG_PCI_MSI
xen: handled remapped IRQs when enabling a pcifront PCI device.
genirq: Add IRQF_FORCE_RESUME
Add tile support for the EDAC driver, which provides unified system
error (memory, PCI, etc.) reporting. For now, the TILEPro port
reports memory correctable error (CE) only.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The Tilera architecture traditionally supports 64KB page sizes
to improve TLB utilization and improve performance when the
hardware is being used primarily to run a single application.
For more generic server scenarios, it can be beneficial to run
with 4KB page sizes, so this commit allows that to be specified
(by modifying the arch/tile/include/hv/pagesize.h header).
As part of this change, we also re-worked the PTE management
slightly so that PTE writes all go through a __set_pte() function
where we can do some additional validation. The set_pte_order()
function was eliminated since the "order" argument wasn't being used.
One bug uncovered was in the PCI DMA code, which wasn't properly
flushing the specified range. This was benign with 64KB pages,
but with 4KB pages we were getting some larger flushes wrong.
The per-cpu memory reservation code also needed updating to
conform with the newer percpu stuff; before it always chose 64KB,
and that was always correct, but with 4KB granularity we now have
to pay closer attention and reserve the amount of memory that will
be requested when the percpu code starts allocating.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This renames 3G_OPT to 2_75G, and adds 2_5G and 2_25G.
For memory-intensive applications that are also network-buffer
intensive it can be helpful to be able to tune the virtual address
of the start of kernel memory.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This is a grab bag of changes with no actual change to generated code.
This includes whitespace and comment typos, plus a couple of stale
comments being removed.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
There should be no reason to call h4_init_flash this
early. It causes problems as things are not yet initialized.
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various binutils versions can resolve Thumb-2 branches to
locally-defined, preemptible global symbols as short-range "b.n"
branch instructions.
This is a problem, because there's no guarantee the final
destination of the symbol, or any candidate locations for a
trampoline, are within range of the branch. For this reason, the
kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
relocation in modules at all, and it makes little sense to add
support.
The symptom is that the kernel fails with an "unsupported
relocation" error when loading some modules.
Until fixed tools are available, passing
-fno-optimize-sibling-calls to gcc should prevent gcc generating
code which hits this problem, at the cost of a bit of extra runtime
stack usage in some cases.
The problem is described in more detail at:
https://bugs.launchpad.net/binutils-linaro/+bug/725126
Only Thumb-2 kernels are affected.
This patch adds a new CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11 config
option which adds -fno-optimize-sibling-calls to CFLAGS_MODULE
when building a Thumb-2 kernel.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding Thumb2 support to the runtime patching of the virt_to_phys and
phys_to_virt opcodes.
Tested both the 8-bit and the 16-bit fixups, using different placements
in memory to exercize all code paths.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the index to the ret_stack is updated and the real return address
is saved in the ret_stack. Then we call the trace function. The trace
function could decide that it doesn't want to trace this function
(ex. set_graph_function does not match) and it will return 0 which means
not to trace this call.
The normal function graph tracer has this code:
if (!(trace->depth || ftrace_graph_addr(trace->func)) ||
ftrace_graph_ignore_irqs())
return 0;
What this states is, if the trace depth (which is curr_ret_stack)
is zero (top of nested functions) then test if we want to trace this
function. If this function is not to be traced, then return 0 and
the rest of the function graph tracer logic will not trace this function.
The problem arises when an interrupt comes in after we updated the
curr_ret_stack. The next function that gets called will have a trace->depth
of 1. Which fools this trace code into thinking that we are in a nested
function, and that we should trace. This causes interrupts to be traced
when they should not be.
The solution is to trace the function first and then update the ret_stack.
Reported-by: zhiping zhong <xzhong86@163.com>
Reported-by: wu zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: David Sharp <dhsharp@google.com>
LKML-Reference: <1291421609-14665-8-git-send-email-dhsharp@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The removal of the single-step emulation from ptrace on ARM means that
thread_struct no longer has software breakpoint fields in its debug
member.
This patch fixes the a.out core dump code so that the debug registers
are zeroed rather than trying to copy from non-existent fields.
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some cards have the CRC errors in read on mx51 BBG board.
Configure the eSDHC pad configurations to level up the
compatibility to fix this issue.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the backlight control code into the appropriate hooks for the LCDC
driver.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the main LCD backlight that is controlled through the
PTR1 GPIO.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain. ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode. They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)
Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.
This patch should allow others to test which clockdomains actually
still need autodeps.
Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:
http://www.spinics.net/lists/linux-omap/msg47277.html
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_init_clock always returns 0 and does
not propogate the error (in case of failure)
back to the caller, causing _init_clocks to
fail silently.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Baseline:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Tested Info:
Boot tested on OMAP 1/2/3/4.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the correct I/O address definitions for Footbridge
peripherals when the kernel is compiled without MMU
support.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit d344272671 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
https://patchwork.kernel.org/patch/590561/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Thara Gopinath <thara@ti.com>
These warnings are missing newlines and spaces causing confusing
looking output when they trigger.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove compilation failure when ftrace in enabled.
Error log:
CC kernel/trace/power-traces.o
In file included from arch/microblaze/include/asm/irq.h:15,
from include/linux/irq.h:27,
from include/asm-generic/hardirq.h:12,
from arch/microblaze/include/asm/hardirq.h:15,
from include/linux/hardirq.h:7,
from include/linux/ftrace_event.h:7,
from include/trace/ftrace.h:19,
from include/trace/define_trace.h:96,
from include/trace/events/power.h:240,
from kernel/trace/power-traces.c:14:
include/linux/interrupt.h: In function '__raise_softirq_irqoff':
include/linux/interrupt.h:413: error: implicit declaration of function 'trace_softirq_raise'
In file included from include/trace/ftrace.h:554,
from include/trace/define_trace.h:96,
from include/trace/events/power.h:240,
from kernel/trace/power-traces.c:14:
include/trace/events/irq.h: In function 'ftrace_test_probe_irq_handler_entry':
include/trace/events/irq.h:37: error: implicit declaration of function 'check_trace_callback_type_irq_handler_entry'
include/trace/events/irq.h: In function 'ftrace_test_probe_irq_handler_exit':
include/trace/events/irq.h:67: error: implicit declaration of function 'check_trace_callback_type_irq_handler_exit'
include/trace/events/irq.h: In function 'ftrace_test_probe_softirq_entry':
include/trace/events/irq.h:112: error: implicit declaration of function 'check_trace_callback_type_softirq_entry'
include/trace/events/irq.h: In function 'ftrace_test_probe_softirq_exit':
include/trace/events/irq.h:126: error: implicit declaration of function 'check_trace_callback_type_softirq_exit'
include/trace/events/irq.h: In function 'ftrace_test_probe_softirq_raise':
include/trace/events/irq.h:140: error: implicit declaration of function 'check_trace_callback_type_softirq_raise'
make[5]: *** [kernel/trace/power-traces.o] Error 1
make[4]: *** [kernel/trace] Error 2
make[3]: *** [kernel] Error 2
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
It's forbidden to take the page_table_lock with the irq disabled
or if there's contention the IPIs (for tlb flushes) sent with
the page_table_lock held will never run leading to a deadlock.
Nobody takes the pgd_lock from irq context so the _irqsave can be
removed.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
LKML-Reference: <201102162345.p1GNjMjm021738@imap1.linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mm_fault_error() should not execute oom-killer, if page fault
occurs in kernel space. E.g. in copy_from_user()/copy_to_user().
This would happen if we find ourselves in OOM on a
copy_to_user(), or a copy_from_user() which faults.
Without this patch, the kernels hangs up in copy_from_user(),
because OOM killer sends SIG_KILL to current process, but it
can't handle a signal while in syscall, then the kernel returns
to copy_from_user(), reexcute current command and provokes
page_fault again.
With this patch the kernel return -EFAULT from copy_from_user().
The code, which checks that page fault occurred in kernel space,
has been copied from do_sigbus().
This situation is handled by the same way on powerpc, xtensa,
tile, ...
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
LKML-Reference: <201103092322.p29NMNPH001682@imap1.linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
if building kernels without OMAP2 support, we
will see a warning such as:
arch/arm/mach-omap2/io.c: In function 'omap2_init_common_infrastructure':
arch/arm/mach-omap2/io.c:389:3: warning: statement with no effect
arch/arm/mach-omap2/io.c:391:3: warning: statement with no effect
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Disable VPNH feature
powerpc/iseries: Fix early init access to lppaca
omap_sr_probe() creates the smartreflex debug directory and its
underlying nvalue debug directory. These directories are removed in
omap_sr_remove().
Basic smartreflex functionality tested on OMAP3630 Zoom3 & OMAP4430 SDP
Signed-off-by: Anand S Sawant <sawant@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Fix an out-of-range ADR when building for ARM.
* Remove deprecated PC-relative stores.
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words.
* Handle non-interworking return from v7_flush_dcache_all.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Build unconditionally as ARM for correct interoperation with
OMAP firmware.
* Remove deprecated PC-relative stores
* Add the required ENDPROC() directive for each ENTRY().
* .align before data words
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For various reasons, Linux now only officially supports being built
with tools which are new enough to understand the SMC instruction.
Replacing the hand-encoded instructions when the mnemonic also
allows for correct assembly in Thumb-2 (otherwise, the result is
random data in the middle of the code).
The Makefile already ensures that this file is built with a high
enough gcc -march= flag (armv7-a).
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Code marked with ENTRY() also needs a matching ENDPROC() directive,
in order to ensure that the type and instruction set of the
symbol are correctly annotated.
ENDPROC() tags the affected symbol as a function symbol, which will
ensure that link-time fixups don't accidentally switch to the
wrong instruction set.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For CONFIG_THUMB2_KERNEL, the existing definition of do_wfi() will
insert invalid code into the instruction stream.
Any assembler which can assemble Thumb-2 is guaranteed to accept
the "wfi" mnemonic, so for the Thumb-2 case, just use the mnemonic.
The ARM case is left as-is.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
IVA device is not present in many OMAP3 variants.
This patch ensures that initialization is tied to
the presence of IVA on the device.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Voltage control on TWL can be done using VMODE/I2C1/I2C_SR.
Since almost all platforms use I2C_SR on omap3, omap3_twl_init by
default expects that OMAP's I2C_SR is plugged in to TWL's I2C
and calls omap3_twl_set_sr_bit. On platforms where I2C_SR is not connected,
the board files are expected to call omap3_twl_set_sr_bit(false) to
ensure that I2C_SR path is not set for voltage control and prevent
the default behavior of omap3_twl_init.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a description field to each idle C-state. This helps to give
better data with PowerTop and one don't have to refer to the code
to link what Cx means from system point of view while analysing
PowerTop data.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the custom restore_control_register() and use the exported
set_cr() instead to set the system control register(SCTRL) value.
No functional change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP2 and OMAP3 PM code clears clockdomain wakeup and sleep
dependencies. This is unnecessary after commit
6f7f63cc9a ("OMAP clockdomain:
initialize clockdomain registers when the clockdomain layer starts")
which clears these dependencies during clockdomain init.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that omap_hwmod + omap_device is used for OMAP UART device and
driver code, we no longer need the UART physical addresses in
omap_globals.
Note that the #defines for the base addresses are still left in
<plat/serial.h> since they are used by DEBUG_LL and uncompress code.
Build tested for OMAP1 (omap1_defconfig) and OMAP2+ (omap2plus_defconfig)
Signed-off-by: Kevin Hilman <khilman@ti.com>
kzalloc() may fail, if so return -ENOMEM. Also Walter Harms suggested
to use kasprintf() instead of kzalloc+strcpy+strcat.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMP3630 silicon can enable higher frequencies only depending on the board
characteristics meeting the recommended standards, and has to be selectively
toggled.
Beagle XM uses 3730 variant and the board design allows enabling 800MHz and
1GHz OPPs. However, We need Smart reflex class 1.5 and ABB to enable 1GHz
safely. For the moment, we tweak the default table to allow for 800Mhz OPP
usage.
Reported-by: Koen Kooi <koen@beagleboard.org>
Tested-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap3 and omap4 opp_init should be made non-static to allow
for platform specific opp table tweaking. making these static
conflicts with the definition in pm.h(global) as well.
we include pm.h as well to ensure that there are no such prototype
conflicts with actual implementation in the future.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case in user has a OMAP3630 < ES1.2 the kernel should warn the user
about the ERRATUM, but using pr_warn instead of WARN_ON is already
enough, as there is nothing else the user can do besides changing the
board.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This feature triggers nasty races in the scheduler between the
rebuilding of the topology and the load balancing code, causing
the machine to hang.
Disable it for now until the races are fixed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The combination of commit
8154c5d22d and
93c22703ef
Broke boot on iSeries.
The problem is that iSeries very early boot code, which generates
the device-tree and runs before our normal early initializations
does need access the lppaca's very early, before the PACA array is
initialized, and in fact even before the boot PACA has been
initialized (it contains all 0's at this stage).
However, the first patch above makes that code use the new
llpaca_of(cpu) accessor, which itself is changed by the second patch to
use the PACA array.
We fix that by reverting iSeries to directly dereferencing the array. In
addition, we fix all iterators in the iSeries code to always skip CPU
whose number is above 63 which is the maximum size of that array and
the maximum number of supported CPUs on these machines.
Additionally, we make sure the boot_paca is properly initialized
in our early startup code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On revisions of the Cortex-A9 prior to r2p0, the Store Buffer does not
have any automatic draining mechanism and therefore a livelock may occur
if an external agent continuously polls a memory location waiting to
observe an update.
This workaround defines cpu_relax() as smp_mb(), preventing correctly
written polling loops from denying visibility of updates to memory.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p* and r3p* versions of the Cortex-A9, a speculative memory
access may cause a page table walk which starts prior to an ASID switch
but completes afterwards. This can populate the micro-TLB with a stale
entry which may be hit with the new ASID.
This workaround places two dsb instructions in the mm switching code so
that no page table walks can cross the ASID switch.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This applies errata fix 753970 for all ux500 platforms. All
current ASICs suffer from this. If the problem is resolved in
later ASICs, the errata selection can be pushed down to other
Kconfig options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle. By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM. When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle. This problem was observed on
N8x0.
Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag. But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC. It may be that the VENC interface should use a
hardware-autoidling interface clock. This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM. Clarification from TI is needed.
Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Return 0 on failure. This will cause the initialization of the driver
to fail and prevent the driver from loading if the BIOS cannot handle
the PCC interface command to "get frequency". Otherwise, the driver
will load and display a very high value like "4294967274" (which is
actually -EINVAL) for frequency:
# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq
4294967274
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
CC: stable@kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
Due to commit 781c5a67f1 it is
likely that the number of areas to scan for BIOS corruption is 0
-- especially when the first 64K is already reserved
(X86_RESERVE_LOW is 64K by default).
If that's the case then don't set up the scan.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: <stable@kernel.org>
LKML-Reference: <20110225202838.2229.71011.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The BAU's initialization of the broadcast description header is
lacking the coherence domain (high bits) in the nasid. This
causes a catastrophic system failure when running on a system
with multiple coherence domains.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1PxKBB-0005F0-3U@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect. The error information
gives the detail regarding the target that was attempted
to be accessed and its corresponding address.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod data base.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod change is aligned with Benoit Cousson.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect.The error info provides
the details regarding the master or the target that
generated the error, type of error and the corresponding address.
The stack dump is also provided.
Signed-off-by: sricharan <r.sricharan@ti.com>
[r.sricharan@ti.com: Enhacements, major cleanup and made it functional]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[santosh.shilimkar@ti.com: Driver design changes as per OMAP4 version]
Signed-off-by: Felipe Balbi <balbi@ti.com>
[balbi@ti.com: Initial version of the driver]
Acked-by: Benoit Cousson <b-cousson@ti.com>
The l3 interconnect device is build with all the data required
to handle the error logging. The data is extracted from the
hwmod database.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Add the address spaces, irqs of the l3 interconnect to the
hwmod data. The hwmod changes are aligned with Benoit Cousson.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Now we used standard SZ_* macros instead of self defined *_SIZE macros. This
patch removes all such unused *_SIZE macros for spear3xx & 6xx.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resource size required mostly is 4K for all devices, whereas currently
reserved space is much beyond that. This patch replaces SIZE macro's used at
multiple places with SZ_4K.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Order of declarations should be: pmx_devs, shirq support, amba_devices,
plat_devices, routines. This patch moves gpio_device below shirq support.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Device name of SD/MMC/SDIO controller in linux is sdhci. To maintain
consistency across all spear code, rename sdio to sdhci.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes inclusion of hardware.h and spear.h consistent over all spear
variants. Now we will include hardware.h, wherever we need to use hardware
macros. spear.h will be automatically included by hardware.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Order of inclusion of .h files must be: <linux/...>, <asm/...>, <plat/...>,
<mach/...>. This patch corrects this ordering whereever it is not followed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Add a dummy clk_set_rate() function. This is required for compilation
of a few drivers.
- Make functions in plat-spear/clock.c more generic over all SPEAr
platforms.
- Add div_factor in struct clk for clks with .recalc = follow_parent
- Change type of register pointers to void __iomem *
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform specific timer initialization code is moved into platform
specific files.
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- compile padmux only for spear3xx
- padmux initialization code rearranged in evaluation board and machine
files.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add IOMEM(x) definition, and use it with MISC_BASE for SPEAr platform.
With this there is no need to typecast misc macros to (unsigned int *).
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This isn't being referenced anywhere, and the selects done from
it can be easily done together with all the other X86 ones.
v2: Also adjust UML's Kconfig.x86.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4D7603DA02000078000351C1@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
New binutils version 2.21.0.20110302-1 started checking that the symbol
parameter to the .size directive matches the entry name's
symbol parameter, unearthing two mismatches:
AS arch/x86/kernel/acpi/wakeup_rm.o
arch/x86/kernel/acpi/wakeup_rm.S: Assembler messages:
arch/x86/kernel/acpi/wakeup_rm.S:12: Error: .size expression with symbol `wakeup_code_start' does not evaluate to a constant
arch/x86/kernel/entry_32.S: Assembler messages:
arch/x86/kernel/entry_32.S:1421: Error: .size expression with
symbol `apf_page_fault' does not evaluate to a constant
The problem was discovered while using Debian's binutils
(2.21.0.20110302-1) and experimenting with binutils from
upstream.
Thanks Alexander and H.J. for the vital help.
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
LKML-Reference: <1299620364-21644-1-git-send-email-sedat.dilek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A userland read of more than PAGE_SIZE bytes from /dev/zero results in
(a) not all of the bytes returned being zero, and
(b) memory corruption due to zeroing of bytes beyond the user buffer.
This is caused by improper constraints on the assembly __clear_user function.
The constrints don't indicate to the compiler that the pointer argument is
modified. Since the function is inline, this results in double-incrementing
of the pointer when __clear_user() is invoked through a multi-page read() of
/dev/zero.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Michal Simek <monstr@monstr.eu>
CC: stable@kernel.org
irq_chip.end got obsolete with the removal of __do_IRQ().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Tested-by: Michal Simek <monstr@monstr.eu>
LKML-Reference: <20110203004210.240154507@linutronix.de>
Warning log:
CHECK arch/microblaze/mm/fault.c
arch/microblaze/mm/fault.c:51:6: warning: incorrect type in initializer (different address spaces)
arch/microblaze/mm/fault.c:51:6: expected unknown type 2const [noderef] *__gu_addr<asn:1>
arch/microblaze/mm/fault.c:51:6: got unsigned int *<noident>
arch/microblaze/mm/fault.c:68:6: warning: symbol 'bad_page_fault' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/sys_microblaze.c
arch/microblaze/kernel/sys_microblaze.c:37:17: warning: symbol 'microblaze_vfork' was not declared. Should it be static?
arch/microblaze/kernel/sys_microblaze.c:43:17: warning: symbol 'microblaze_clone' was not declared. Should it be static?
arch/microblaze/kernel/sys_microblaze.c:50:17: warning: symbol 'microblaze_execve' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/cpu/cache.c
arch/microblaze/kernel/cpu/cache.c:522:21: warning: symbol 'wb_msr' was not declared. Should it be static?
arch/microblaze/kernel/cpu/cache.c:538:21: warning: symbol 'wb_nomsr' was not declared. Should it be static?
arch/microblaze/kernel/cpu/cache.c:554:21: warning: symbol 'wt_msr' was not declared. Should it be static?
arch/microblaze/kernel/cpu/cache.c:569:21: warning: symbol 'wt_nomsr' was not declared. Should it be static?
arch/microblaze/kernel/cpu/cache.c:585:21: warning: symbol 'wt_msr_noirq' was not declared. Should it be static?
arch/microblaze/kernel/cpu/cache.c:600:21: warning: symbol 'wt_nomsr_noirq' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/cpu/cpuinfo-static.c
arch/microblaze/include/asm/cpuinfo.h:101:21: warning: incorrect type in argument 1 (different signedness)
arch/microblaze/include/asm/cpuinfo.h:101:21: expected unsigned int const [usertype] *p
arch/microblaze/include/asm/cpuinfo.h:101:21: got int *[assigned] val
...
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/unwind.c
arch/microblaze/kernel/unwind.c:186:6: warning: symbol 'microblaze_unwind_inner' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning in dma.c was caused by incorrect type in consistent_alloc function.
Warning log:
CHECK arch/microblaze/kernel/dma.c
arch/microblaze/kernel/dma.c:53:26: warning: incorrect type in argument 1 (different base types)
arch/microblaze/kernel/dma.c:53:26: expected int [signed] gfp
arch/microblaze/kernel/dma.c:53:26: got restricted unsigned int [usertype] flag
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/ptrace.c
arch/microblaze/kernel/ptrace.c:126:11: warning: incorrect type in initializer (different address spaces)
arch/microblaze/kernel/ptrace.c:126:11: expected unknown type 2[noderef] *__pu_addr<asn:1>
arch/microblaze/kernel/ptrace.c:126:11: got unsigned long *<noident>
arch/microblaze/kernel/ptrace.c:134:17: warning: symbol 'do_syscall_trace_enter' was not declared. Should it be static?
arch/microblaze/kernel/ptrace.c:157:17: warning: symbol 'do_syscall_trace_leave' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Function sw_exception is linked with asm code.
Warning log:
CHECK arch/microblaze/kernel/exceptions.c
arch/microblaze/kernel/exceptions.c:53:6: warning: symbol 'sw_exception' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Variables and init_microblaze_timecounter should be static.
Warning log:
CHECK arch/microblaze/kernel/timer.c
arch/microblaze/kernel/timer.c:41:14: warning: symbol 'freq_div_hz' was not declared. Should it be static?
arch/microblaze/kernel/timer.c:42:14: warning: symbol 'timer_clock_freq' was not declared. Should it be static?
arch/microblaze/kernel/timer.c:205:12: warning: symbol 'init_microblaze_timecounter' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/dma.c
arch/microblaze/kernel/dma.c:53:26: warning: incorrect type in argument 1 (different base types)
arch/microblaze/kernel/dma.c:53:26: expected int [signed] gfp
arch/microblaze/kernel/dma.c:53:26: got restricted unsigned int [usertype] flag
Signed-off-by: Michal Simek <monstr@monstr.eu>
Used the same solution as SH. Changed len to PAGE_SIZE
in copy_to_user_page macro.
Implement flush_cache_page macro.
Signed-off-by: Michal Simek <monstr@monstr.eu>
"la" pseudo instruction is only translation to "addik".
Use directly "addik" which is described in the MB reference guide.
Signed-off-by: Michal Simek <monstr@monstr.eu>
r0_ram pool was used for saving/restoring register
content if hw exception happen. This poll was replaced by
pt_pool_space with PT_SIZE size.
Based on this change SAVE_STATE_ARG_SPACE was removed which
caused that PTO offset is zero that's why is also removed.
r0_ram space was used as scratchpad by v850. In early
Microblaze Linux developing phase was this part of code
blindly copied.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Save 0x1 word to rodata section and remove online value
loading if DTB is passed from bootloader. It saves two
asm instructions in bootup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Remove hw exception counting space from r0_ram. Use special
exception_debug_table poll for exception statistic.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Use straight 64-bit values as 64-bit operations are fairly efficient on ARM.
Comparing the asm output with and without KTIME_SCALAR, using 64-bit math
generates clearly better code.
Comparing kernel/hrtimer.c .text size, it goes from 0x1414 to 0x119c with
this change.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The simply expanded variable may be evaluated before the target file for
the stat command is up to date or even exists. Switching to a recursively
expanded variable move the execution of the stat command to the location
where LDFLAGS_vmlinux is actually used, fixing the dependency issue
introduced by patch #6746/1.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Few architectures combine the GIC with an external interrupt
controller. On such systems it may be necessary to update both
the GIC registers and the external controller's registers to control
IRQ behavior.
This can be addressed in couple of possible methods.
1. Export common GIC routines along with 'struct irq_chip gic_chip'
and allow architectures to have custom function by override.
2. Provide architecture specific function pointer hooks
within GIC library and leave platforms to add the necessary
code as part of these hooks.
First one might be non-intrusive but have few shortcomings like arch
needs to have there own custom gic library. Locks used should be
common since it caters to same IRQs etc. Maintenance point of view
also it leads to multiple file fixes.
The second probably is cleaner and portable. It ensures that all the
common GIC infrastructure is not touched and also provides archs to
address their specific issue.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Tested-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Populate the l2x0 set_debug function pointer with OMAP secure call
and enable the PL310 Errata 727915
This patch has dependency on the earlier patch
ARM: l2x0: Errata fix for flush by Way operation can cause data
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 implements the Clean & Invalidate by Way L2 cache maintenance
operation (offset 0x7FC). This operation runs in background so that
PL310 can handle normal accesses while it is in progress. Under very
rare circumstances, due to this erratum, write data can be lost when
PL310 treats a cacheable write transaction during a Clean & Invalidate
by Way operation.
Workaround:
Disable Write-Back and Cache Linefill (Debug Control Register)
Clean & Invalidate by Way (0x7FC)
Re-enable Write-Back and Cache Linefill (Debug Control Register)
This patch also removes any OMAP dependency on PL310 Errata's
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i2c_board_info entry supporting AIC23 codec was added into
the i2c2 bus.
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3cf32bba8c ("OMAP: McBSP: Convert
McBSP to platform device model") breaks compilation with non-multi-OMAP1
configs:
CC arch/arm/mach-omap1/mcbsp.o
arch/arm/mach-omap1/mcbsp.c: In function 'omap1_mcbsp_init':
arch/arm/mach-omap1/mcbsp.c:384: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:387: error: invalid use of void expression
arch/arm/mach-omap1/mcbsp.c:390: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:393: error: invalid use of void expression
Fix by avoiding NULL dereferences.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated description not to remove unnecessary branch name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow the MSM8960 IOMMU to access its page tables directly
through the L2 cache.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Don't read from V2Pxx command registers when doing
iova-to-phys operations. These registers are write-only and
reading the value before modifying the VA bits is
unnecessary.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Remove the depencency on the IOMMU IDR register, as it may
not be accessible depending on the security configuraton.
This involves moving the NCB field of IDR into the platform
data.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Use ASID tags in the TLB instead of VMID tags in
preparation for changes to the secure environment.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Clean up the clock control code in the probe calls, and add
support for controlling the clock for the IOMMU bus
interconnect. With the (proper) clock driver in place, the
clock control logic in the probe function can be made much
cleaner since it does not have to deal with the placeholder
driver anymore.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add clock control to the IOMMU driver. The IOMMU bus clock
(and potentially an AXI clock) need to be on to gain access
to IOMMU registers. Actively control these clocks when
needed instead of leaving them on.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
You can crash the kernel (with root/admin privileges) using kprobe tracer by running:
echo "p system_call_after_swapgs" > ./kprobe_events
echo 1 > ./events/kprobes/enable
The reason is that at the system_call_after_swapgs label, the
kernel stack is not set up. If optimized kprobes are enabled,
the user space stack is being used in this case (see optimized
kprobe template) and this might result in a crash.
There are several places like this over the entry code
(entry_$BIT). As it seems there's no any reasonable/maintainable
way to disable only those places where the stack is not ready, I
switched off the whole entry code from kprobe optimizing.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: acme@redhat.com
Cc: fweisbec@gmail.com
Cc: ananth@in.ibm.com
Cc: davem@davemloft.net
Cc: a.p.zijlstra@chello.nl
Cc: eric.dumazet@gmail.com
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <1298298313-5980-3-git-send-email-jolsa@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Put x86 entry code into a separate link section: .entry.text.
Separating the entry text section seems to have performance
benefits - caused by more efficient instruction cache usage.
Running hackbench with perf stat --repeat showed that the change
compresses the icache footprint. The icache load miss rate went
down by about 15%:
before patch:
19417627 L1-icache-load-misses ( +- 0.147% )
after patch:
16490788 L1-icache-load-misses ( +- 0.180% )
The motivation of the patch was to fix a particular kprobes
bug that relates to the entry text section, the performance
advantage was discovered accidentally.
Whole perf output follows:
- results for current tip tree:
Performance counter stats for './hackbench/hackbench 10' (500 runs):
19417627 L1-icache-load-misses ( +- 0.147% )
2676914223 instructions # 0.497 IPC ( +- 0.079% )
5389516026 cycles ( +- 0.144% )
0.206267711 seconds time elapsed ( +- 0.138% )
- results for current tip tree with the patch applied:
Performance counter stats for './hackbench/hackbench 10' (500 runs):
16490788 L1-icache-load-misses ( +- 0.180% )
2717734941 instructions # 0.502 IPC ( +- 0.079% )
5414756975 cycles ( +- 0.148% )
0.206747566 seconds time elapsed ( +- 0.137% )
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: masami.hiramatsu.pt@hitachi.com
Cc: ananth@in.ibm.com
Cc: davem@davemloft.net
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20110307181039.GB15197@jolsa.redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This typo was fixed in 46e3f30 (mx25: fix spi device registration typo), but a
the merge at 0e44e059 (Merge commit 'v2.6.37-rc4' into imx-for-2.6.38) resolved
the merge conflict wrongly.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
TrimSlice has MicroSD and standard MMC/SD slots.
Register sdhci devices and enable GPIOs for MMC/SD slot.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
Add a clockdomain to the GPTIMER7 interface and 2430 HSMMC2 functional
clocks - both were previously missing them.
Also, the 2430 mmchs1_fck is in core_l3_clkdm, but should be in
core_l4_clkdm; fix this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes these warnings when building kernel for OMAP3EVM
only.
CC arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.o
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:95: warning:
'dsp_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:119: warning:
'mpu_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:147: warning:
'core_24xx_wkdeps' defined but not used
The problem should be noticed when building for other OMAP3
platforms (only) as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit 81b34fbecb ("OMAP2 clock:
split OMAP2420, OMAP2430 clock data into their own files"), it's
possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock
files. It was originally only needed due to a 2420/2430 clock tree difference,
and now that the data is in separate files, it's superfluous.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined. The intention is to
reduce and simplify the work that is done inside the spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The parent of the interface clocks for GPTIMER1, MPU_WDT,
SYNCTIMER_32K, SCM, WDT1, and the ICR (2430 only) were all listed as
being l4_ck. This isn't accurate; these modules exist inside the WKUP
domain, and the interface clock to these modules runs at the SYS_CLK
rate rather than the CORE L4 rate.
So, create a new clock "wu_l4_ick", similar to the OMAP3
"wkup_l4_ick", that serves as the parent for these clocks.
Also, these clocks were listed as existing inside core_l4_clkdm;
wkup_clkdm is probably more accurate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2420/2430 external 32-kHz low-frequency oscillator is a 32768
Hz oscillator, not a 32,000 Hz oscillator[1][2]. Fix this in the clock
tree.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
1. OMAP2420/22 Multimedia Processor Data Manual, Version P [SWPS019P],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
2. OMAP2430 Multimedia Processor ES2.1 Data Manual, Version V [SWPS023V],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
Several clocks are listed as having the core L4 clock as their parent,
when they are actually derived from the L3 clock. Fix these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h. It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2430 and OMAP3xxx have modem autoidle bits that are actually
attached to clocks with CM_FCLKEN bits; add the code and data to
handle these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add sdrc_ick to the OMAP2420 clock data so the clock code can control
the CM_AUTOIDLE bit associated with this clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add interface clock type code with autoidle enable/disable support.
The clkops structures created in this file will be used for all
OMAP2/3 interface clocks with autoidle support. They will enable the
clock framework to control interface clock autoidle directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Place some comments in the OMAP oscillator clock control code to note that
its autoidle mode should eventually be controlled via the new OMAP clockfw
autoidle control interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2xxx devices have two on-chip APLLs. These APLLs can
automatically enter idle when not in use. Connect the APLL autoidle
code to the clock code, so that the clock framework can handle this
process. As part of this patch, remove the code in mach-omap2/pm24xx.c
that previously handled APLL autoidle control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add the necessary code and data to allow the clock framework to enable
and disable the OMAP2 DPLL autoidle state. This is so the direct
register access can be moved out of the mach-omap2/pm24xx.c code, and other
code that needs to control this (e.g., CPUIdle) can do so via an API.
As part of this patch, remove the pm24xx.c code that formerly wrote
directly to the autoidle bits.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Some drivers wish to know whether the device that they control can
ever lose context, for example, when the device's enclosing
powerdomain loses power. They can use this information to determine
whether it is necessary to save and restore device context, or whether
it can be skipped. Implement the powerdomain portion of this by
adding the function pwrdm_can_ever_lose_context(). This is not for
use directly from driver code, but instead is intended to be called
from driver-subarch integration code (i.e., arch/arm/*omap* code).
Currently, the result from this function should be passed into the
driver code via struct platform_data, but at some point this should
be part of some common or OMAP-specific device code.
While here, update file copyrights.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The bank power state bitfields in the powerdomain data are
encoded incorrectly. These fields are intended to be bitfields,
representing a set of power states that the memory banks support.
However, when only one power state was supported by a given bank,
the field was incorrectly set to the bit shift -- not the mask.
While here, update some file copyrights.
The OMAP4 autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Mark the WKUP powerdomain as being always on -- at least, as long as the
chip has power. This will be used to enable the powerdomain code to
determine whether a given powerdomain is ever able to power off. While
here, update the file copyright.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a keyctl op (KEYCTL_INSTANTIATE_IOV) that is like KEYCTL_INSTANTIATE, but
takes an iovec array and concatenates the data in-kernel into one buffer.
Since the KEYCTL_INSTANTIATE copies the data anyway, this isn't too much of a
problem.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Enable new platforms and tegra drivers in tegra_defconfig. Also enable
some of the common devices several platforms, and GUID partition tables
to make it possible to boot a tegra_defconfig kernel with a ChromiumOS
filesystem.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch adds the config infrastructure, the pinmux and basic
board setup code for PAZ00 (name of board inside the AC100/AZ).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the final patch to enable audio support on Harmony. It additionally
relies on the latest ASoC branch being merged in, which provides the header
defining the gpio_base field in the WM8903 platform data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is the portion of the audio-related setup that relies additionally
on the latest Tegra I2C driver being merged.
* Define platform data for WM8903 audio codec
* Register WM8903 as an I2C device
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Register the base i2c busses on harmony. Devices coming at a later date,
but this allows for hand-probing of some of them at least.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Register the base i2c devices on seaboard. A few more are pending,
but it's a start.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This change includes everything required to enable audio on Harmony, except
those parts which rely on code not currently in Tegra's for-next branch, i.e.
except those parts which rely on merges of the Tegra I2C driver or latest
ASoC subsystem.
* Define GPIO names for audio-related GPIOs
* Set up platform data and platform device for ASoC machine driver
* Register audio-related platform devices
* Initialize audio-related clocks
* Correctly configure pinmux and GPIO enables for audio-related pins
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This ensures they're kept in sync between platform_data definitions and
the GPIO table initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables lcd and backlight drivers in NURI board.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the parent clock for watchdog timer for EXYNOS4.
Signed-off-by: Inderpal Singh <inderpal.s@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
This patch changes these boards to use the common implementation for GPIO
controlled pullup in the UDC driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes:
arch/arm/kernel/built-in.o: In function `__irq_svc':
io.c:(.text+0x2e0): undefined reference to `avic_base'
arch/arm/kernel/built-in.o: In function `__irq_usr':
io.c:(.text+0x4c8): undefined reference to `avic_base'
arch/arm/mach-mxc91231/built-in.o: In function `mxc91231_init_irq':
magx-zn5.c:(.init.text+0x18): undefined reference to `mxc_init_irq'
and was broken by
c7259df (ARM i.MX irq: Compile avic irq code only on SoCs that need it)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The platform data for the otg port is present but never used, so
remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_smd board only RX/TX pins are used on UART2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
changes since v2:
- use v3 and v4 for specifying the ip version instead of i.MX23/28.
This is a better namespace when future versions are added.
- rename mach/fb.h to mach/mxsfb.h
changes since v1:
- Add a LCDC_ prefix to the register names.
- use set/clear registers where appropriate
- protect call to mxsfb_disable_controller() in mxsfb_remove()
with a (host->enabled) as suggested by Lothar Wassmann
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-fbdev@vger.kernel.org
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following warning in a mx3_defconfig build:
arch/arm/mach-mx3/mach-bug.c: In function 'bug_board_init':
arch/arm/mach-mx3/mach-bug.c:47: warning: passing argument 1 of 'mxc_iomux_setup_multiple_pins' discards qualifiers from pointer target type
While at it remove some useless consts from unsigned int arguments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Visstrim_M10 boards have an TI tlv320aic3204 codec
attached to SSI1.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It seems vim's autocompletion played tricks on me without me noticing.
This was intruduced in
97976e2 (ARM: mx3: use .init_early to initialize cpu type, reset address and iomuxer)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the "i.MX35 (MCIMX35) Multimedia Applications Processor
Reference Manual" the correct address for the pad control register
IOMUXC_SW_PAD_CTL_PAD_ATA_DATA3 is 0x06ec, not 0x6e8.
Signed-off-by: Ryan Lortie <desrt@desrt.ca>
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code created by Lothar Waßmann, Sascha Hauer, Wolfram Sang and
me.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
It is used for example in the i2c driver which can be compiled modular.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The regulator API ifdefs itself out when not enabled
so there is no need for users to do this.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that the dw_dmac DMA driver supports configurable Flow Controller, source
and destination burst or msize, we need to specify which ones to use. Msize or
burst size was previously hardcoded to 1, Flow controller was DMA for both
M2P & P2M transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for CS4271 SPI-connected CODEC to EDB93xx.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
[np: used min_t() as suggested by Sergei Shtylyov <sshtylyov@mvista.com>]
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Originally the FPGA ID checking switch statement left disabled all the
TS implemented FPGA devices if the ID was unknown to it. Michael Spang
created a fix in f9b1184e that changed the default to enable the devices
in the event TS silently release more revisions into the wild, this
unfortunately breaks custom FPGA bitstreams.
This patch amends the switch statement so that the TS devices are only
enabled if on the revision number is unknown (whilst the magic matches).
Changelog:
v2: neater implementation and some cosmetic changes
v1: initial release <20110305112937.GA22117@chipmunk>
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
I'm sure it was a mere oversight that the CONFIG_ prefixes are
missing.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Dave Jones <davej@redhat.com>
LKML-Reference: <4D7118D30200007800034F79@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1299119690-13991-5-git-send-email-ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the manufacturer increases the revision number the platform
devices for the RTC, NAND, and RNG disappear. We should assume
new revisions have these devices instead of assuming they do not.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: iflush: update anomaly 05000491 workaround
Blackfin: outs[lwb]: make sure count is greater than 0
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Change __nosave_XXX symbols to long
sh: Flush executable pages in copy_user_highpage
sh: Ensure ST40-300 BogoMIPS value is consistent
sh: sh7750: Fix incompatible pointer type
sh: sh7750: move machtypes.h to include/generated
The following commit: 38698be:
OMAP2+: clockevent: set up GPTIMER clockevent hwmod right before timer init
Fixed properly the issue with early init for the timer1
So reverts commit 3b03b58dab that is now
generated a warning at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Undetermined entries in emu_nid_to_phys[] are filled with zero
assuming that physical node 0 is always online; however, this might
not be true depending on hardware configuration. Find a physical node
which is actually online and use it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1103020628210.31626@chino.kir.corp.google.com>
This crash happens on a system that does not have RAM on node0.
When numa_emulation is compiled in, and:
1. we boot the system without numa=fake...
2. or we boot the system with numa=fake=128 to make emulation fail
we will get:
[ 0.076025] ------------[ cut here ]------------
[ 0.080004] kernel BUG at arch/x86/mm/numa_64.c:788!
[ 0.080004] invalid opcode: 0000 [#1] SMP
[...]
need to use early_cpu_to_node() directly, because cpu_to_apicid
and apicid_to_node will return node0 that is not onlined.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
LKML-Reference: <4D6ECF72.5010308@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch cleans initmem_init() so that it is more readable and doesn't
use an unnecessary array of function pointers to convolute the flow of
the code. It also makes it obvious that dummy_numa_init() will always
succeed (and documents that requirement) so that the existing BUG() is
never actually reached.
No functional change.
-tj: Updated comment for dummy_numa_init() slightly.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
On Intel Nehalem and Westmere CPUs the generic perf LLC-* events count the
L2 caches, not the real L3 LLC - this was inconsistent with behavior on
other CPUs.
Fixing this requires the use of the special OFFCORE_RESPONSE
events which need a separate mask register.
This has been implemented by the previous patch, now use this infrastructure
to set correct events for the LLC-* on Nehalem and Westmere.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1299119690-13991-3-git-send-email-ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change logs against Andi's original version:
- Extends perf_event_attr:config to config{,1,2} (Peter Zijlstra)
- Fixed a major event scheduling issue. There cannot be a ref++ on an
event that has already done ref++ once and without calling
put_constraint() in between. (Stephane Eranian)
- Use thread_cpumask for percore allocation. (Lin Ming)
- Use MSR names in the extra reg lists. (Lin Ming)
- Remove redundant "c = NULL" in intel_percore_constraints
- Fix comment of perf_event_attr::config1
Intel Nehalem/Westmere have a special OFFCORE_RESPONSE event
that can be used to monitor any offcore accesses from a core.
This is a very useful event for various tunings, and it's
also needed to implement the generic LLC-* events correctly.
Unfortunately this event requires programming a mask in a separate
register. And worse this separate register is per core, not per
CPU thread.
This patch:
- Teaches perf_events that OFFCORE_RESPONSE needs extra parameters.
The extra parameters are passed by user space in the
perf_event_attr::config1 field.
- Adds support to the Intel perf_event core to schedule per
core resources. This adds fairly generic infrastructure that
can be also used for other per core resources.
The basic code has is patterned after the similar AMD northbridge
constraints code.
Thanks to Stephane Eranian who pointed out some problems
in the original version and suggested improvements.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1299119690-13991-2-git-send-email-ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch updates PEBS event constraints for Intel Atom, Nehalem, Westmere.
This patch also reorganizes the PEBS format/constraint detection code. It is
now based on processor model and not PEBS format. Two processors may use the
same PEBS format without have the same list of PEBS events.
In this second version, we simplified the initialization of the PEBS
constraints by leveraging the existing switch() statement in perf_event_intel.c.
We also renamed the constraint tables to be more consistent with regular
constraints.
In this 3rd version, we drop BR_INST_RETIRED.MISPRED from Intel Atom as it does
not seem to work. Use MISPREDICTED_BRANCH_RETIRED instead. Also add FP_ASSIST.*
o both Intel Nehalem and Westmere. I misssed those in the earlier patches.
Events were tested using libpfm4 perf_examples.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4d6e6b02.815bdf0a.637b.07a7@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch reverts NUMA affine page table allocation added by commit
1411e0ec31 (x86-64, numa: Put pgtable to local node memory).
The commit made an undocumented change where the kernel linear mapping
strictly follows intersection of e820 memory map and NUMA
configuration. If the physical memory configuration has holes or NUMA
nodes are not properly aligned, this leads to using unnecessarily
smaller mapping size which leads to increased TLB pressure. For
details,
http://thread.gmane.org/gmane.linux.kernel/1104672
Patches to fix the problem have been proposed but the underlying code
needs more cleanup and the approach itself seems a bit heavy handed
and it has been determined to revert the feature for now and come back
to it in the next developement cycle.
http://thread.gmane.org/gmane.linux.kernel/1105959
As init_memory_mapping_high() callsites have been consolidated since
the commit, reverting is done manually. Also, the RED-PEN comment in
arch/x86/mm/init.c is not restored as the problem no longer exists
with memblock based top-down early memory allocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
If firmware allows us to map all of a partition's memory for DMA on a
particular bridge, create a 1:1 mapping of that memory. Add hooks for
dealing with hotplug events. Dynamic DMA windows can use larger than the
default page size, and we use the largest one possible.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move SPRN_PID declearations in various locations into one place.
Signed-off-by: Tseng-Hui (Frank) Lin <thlin@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create the lnx,oops-log NVRAM partition, and capture the end of the printk
buffer in it when there's an oops or panic. If we can't create the
lnx,oops-log partition, capture the oops/panic report in ibm,rtas-log.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adapt the functions used to create and write to the RTAS-log partition
to work with any OS-type partition.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The debugfs support added to the regulator API (which has been merged
in during this merge window) creates directories for regulators named
after the display names for the regulators so replace / as a separator
for multiple supplies with + in the SMDK6410 machine.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Avoid relying on implicit inclusion of machine.h
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Reduce the logging output of s3c64xx_dma_init1() as it is not useful
for normal bootup (and we get an overall indication of the registration
of the PL180 DMA block).
This removes the following output from the log:
s3c64xx_dma_init1: registering DMA 0 (e0808100)
s3c64xx_dma_init1: registering DMA 1 (e0808120)
s3c64xx_dma_init1: registering DMA 2 (e0808140)
s3c64xx_dma_init1: registering DMA 3 (e0808160)
s3c64xx_dma_init1: registering DMA 4 (e0808180)
s3c64xx_dma_init1: registering DMA 5 (e08081a0)
s3c64xx_dma_init1: registering DMA 6 (e08081c0)
s3c64xx_dma_init1: registering DMA 7 (e08081e0)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The MMC core calls s3c6400_setup_sdhcp_cfg_card() very frequently, causing
the log message in there at KERN_INFO to be displayed a lot which is slow
and overly chatty. Convert the message into a pr_debug() to tone this down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The clock for i2c1 has been missing for a while, add it to the list of
clocks for the system and ensure it is initialised at startup.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
No need to put these in the global namespace and sparse gets upset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ensures that the declaration agrees with the definition and makes sparse
happy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The call to s3c_gpio_cfgrange_nopull() takes a size and base
but this looks like it is trying to do base and end. This means
it is configuring too many GPIOs and on the case of the Cragganmore
means we're seeing an overflow of the ROW pins causing problems
with the keyboard driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The gta02 header file still uses the old S3C2410_GPJx defines instead of the
S3C2410_GPJ(x) macro. Since the S3C2410_GPJx defines have already been removed
this causes the following build failure:
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_set_spk':
sound/soc/samsung/neo1973_wm8753.c:259: error: 'S3C2440_GPJ2' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c:259: error: (Each undeclared identifier is reported only once
sound/soc/samsung/neo1973_wm8753.c:259: error: for each function it appears in.)
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_get_spk':
sound/soc/samsung/neo1973_wm8753.c:267: error: 'S3C2440_GPJ2' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_event':
sound/soc/samsung/neo1973_wm8753.c:276: error: 'S3C2440_GPJ1' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c: At top level:
sound/soc/samsung/neo1973_wm8753.c:439: error: 'S3C2440_GPJ2' undeclared here (not in a function)
sound/soc/samsung/neo1973_wm8753.c:440: error: 'S3C2440_GPJ1' undeclared here (not in a function)
This patches fixes the issue by doing a s,S3C2410_GPJ([\d]+),S3C2410_GPJ(\1),g
on the file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modifies the number of total GPIO lines for Bank F
for Samsung S5P6440 and S5P6450 SoCs from 2 to 16.
This is necessary as the GPIO lines from 0 to 13 are reserved
and only lines 14 and 15 are used. As during initialization,
the line number starts at 0, putting 2 does not solve the
intended purpose.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The gta02 mach file references the ohci device.
So we need to select S3C_DEV_USB_HOST to have the device available.
This fixes the following linker errors:
arch/arm/mach-s3c2440/built-in.o: In function 'gta02_machine_init':
mach-gta02.c:(.init.text+0x370): undefined reference to 's3c_ohci_set_platdata'
arch/arm/mach-s3c2440/built-in.o:(.init.data+0xac): undefined reference to 's3c_device_ohci'
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some devices will use the outs* funcs with a length of zero, so make sure
we do not write any data in that case.
Reported-by: Gilbert Inho <gneny@edevice.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds Samsung ARMLEX4210 board support file
which is based on Exynos4210.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[kgene.kim@samsung.com: added clk_type for hsmmc3]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds basic definitions for MAX8952 & LP3974 (MAX8998
compatible) PMICs for UniversalC210 board. Power consumers for the
device drivers will be added later. These two PMICs occupy I2C5 bus.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung NURI board support.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently tegra_pcie_init is effectively called as subsys_initcall. With
multiplatform kernel this may cause hangs on boards that don't intend to
support Tegra2 PCI-e. Ensure that TrimSlice board code initializes PCI-e
only when actually running on the TrimSlice.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Colin Cross <ccross@android.com>
Move tegra_pcie_power_off before tegra_pcie_power_on for clean addition
of PCIE power gating
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Colin Cross <ccross@android.com>
These are not currently used anywhere, but when the relevant
peripherals are enabled on the Dove port, the IRQ numbers should be
passed into the drivers via platform device resources rather than
having the drivers get them from platform headers directly.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch makes the various mach dirs that use the plat-orion GPIO
code pass in GPIO-related platform info (GPIO controller base address,
secondary base IRQ number, etc) explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch declares the i2c audio codec and initialise audio.
It's adding the alc5621 codec in the i2c board info and is calling
kirkwood_audio_init() to initialize kirkwood audio.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
New FPGA revisions have been released and seen in the wild on the
platform, so it's time to update the list.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Initialize PCIE1 on the 6282-based QNAP TS-419P+ since it has a Marvell 9125
SATA chip on each PCI bus.
Signed-off-by: Zintis Pētersons <zintis.petersons@abcsolutions.lv>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Use the machine-specific kexec_reinit hook to make sure
PCIe is enabled before starting a new kernel.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
PCIe may have been disabled (by kirkwood_clock_gate)
if this kernel was started by kexec. Make sure PCIe
is enabled before attempting to access the device ID
register, otherwise the system will hang.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Provide the option to call a machine-specific function
before kexec'ing a new kernel.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The NAND supports 32bit reads and writes so lets stop shunting 8bit
chunks across the bus.
Doing a dumb 'dd' benchmark, this increases performance roughly like so:
* read: 1.3MB/s to 3.4MB/s
* write: 614kB/s to 882kB/s
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
omap4 interrupt disable bits is different. On rx kfifo full, the mbox rx
interrupts wasn't getting disabled, and this is causing the rcm stress tests
to hang.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Armando Uribe <x0095078@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patches missed an indirect use of IRQF_NO_SUSPEND pulled in via
IRQF_TIMER. The following patch fixes the issue.
With this fixlet PV guest migration works just fine. I also booted the
entire series as a dom0 kernel and it appeared fine.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This happens to not be an issue currently because we take pains to try
to ensure that the GSI-IRQ mapping is 1-1 in a PV guest and that
regular event channels do not clash. However a subsequent patch is
going to break this 1-1 mapping.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
With this patch, we diligently set regions that will be used by the
balloon driver to be INVALID_P2M_ENTRY and under the ownership
of the balloon driver. We are OK using the __set_phys_to_machine
as we do not expect to be allocating any P2M middle or entries pages.
The set_phys_to_machine has the side-effect of potentially allocating
new pages and we do not want that at this stage.
We can do this because xen_build_mfn_list_list will have already
allocated all such pages up to xen_max_p2m_pfn.
We also move the check for auto translated physmap down the
stack so it is present in __set_phys_to_machine.
[v2: Rebased with mmu->p2m code split]
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Make functions used strictly in bool context return bool. Also,
fixup used types and comments, and make a local function static,
while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Borislav Petkov <bp@amd64.org>
LKML-Reference: <20110303115932.GA8603@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add extra parentheses around a couple of definitions introduced
by "x86: Cleanup vector usage" and used in assembly macro
arguments, and remove spaces. Without that old (2.16.1) gas
would see more macro arguments than were actually specified.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <4D6F81B10200007800034B0B@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
of/promtree: allow DT device matching by fixing 'name' brokenness (v5)
x86: OLPC: have prom_early_alloc BUG rather than return NULL
of/flattree: Drop an uninteresting message to pr_debug level
of: Add missing of_address.h to xilinx ehci driver
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] p4-clockmod: print EST-capable warning message only once
[CPUFREQ] fix BUG on cpufreq policy init failure
[CPUFREQ] Fix another notifier leak in powernow-k8.
[CPUFREQ] Missing "unregister_cpu_notifier" in powernow-k8.c
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix call to flush_ptrace_hw_breakpoint()
powerpc/kexec: Restore ppc_md.machine_kexec
powerpc/mm: Make hpte_need_flush() safe for preemption
Once acpi_map_lsapic() in ia64 follows how x86 treats it wrt section
placement, the whole tree from acpi_processor_set_pdc() can become
__cpuinit.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for LCD backlight control using PWM timer
for Samsung's SMDKV210 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDKC100 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight control using PWM timer
for Samsung SMDK6450 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight control using PWM timer
for Samsung SMDK6440 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDK6410 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch does the following:-
1. It moves file pwm.c from plat-s3c24xx to plat-samsung. This will
enable all machines with Samsung SoCs to make use of the same code.
2. The device definitions have been separated to a new file dev-pwm.c
for better clarity and structure.
3. It will enable all Samsung S3C and S5P series SoC's to use common
PWM Kconfig definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
twl4030_codec_audio and twl4030_codec_vibra_data has unused field.
In order to remove it, corresponding settings needs to be removed
from board files.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added the KIM (Kernel initialization module for the
Shared Transport driver) device entry in the board file
Only the Blutooth enable GPIO is set for now
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the OMAP3430LDP board, the ads7846 touchscreen controller
is powered by VAUX1 regulator (supplying 3.0v).
Fix this mapping in the board file, and hence prevent
the ads7846 driver init to fail with the below error..
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: arch/arm/plat-omap/built-in.o(.data+0x6d4): Section mismatch in reference from the variable omap_driver to the function .init.text:omap_cpu_init()
The variable omap_driver references
the function __init omap_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The prototype for sn_pci_provider->{dma_map,dma_map_consistent} expects
an unsigned long instead of a u64.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64_mca_cpu_init has a void *data local variable that is assigned
the value from either __get_free_pages() or mca_bootmem(). The problem
is that __get_free_pages returns an unsigned long and mca_bootmem, via
alloc_bootmem(), returns a void *. format_mca_init_stack takes the void *,
and it's also used with __pa(), but that casts it to long anyway.
This results in the following build warning:
arch/ia64/kernel/mca.c:1898: warning: assignment makes pointer from
integer without a cast
Cast the return of __get_free_pages to a void * to avoid
the warning.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> wrote:
> While working on an defconfig (arm/mx27) I noticed that just updating
> it results in removing CONFIG_EEPROM_AT24=y. The reason is that
> since commit
>
> v2.6.36-5965-g5f2365d (misc devices: do not enable by default)
>
> MISC_DEVICES isn't enabled anymore by default. So all defconfigs that
> have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
> MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
> problem.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
..similar to what sparc's prom_early_alloc does.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irq descriptors are initialized IRQ_DISABLED in the generic
code. No need to fiddle with them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matt Turner <mattst88@gmail.com>
This Patch frees all the dynamically allocated memory
which couldn't have been released in some error hitting cases.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Handling of out-of-bounds distances and allocation failure can use
better documentation. Add it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
NUMA distance table handling has the following problems.
* numa_reset_distance() uses numa_distance * sizeof(numa_distance[0])
as the table size when it should be using the square of
numa_distance.
* The same size miscalculation when allocation space for phys_dist in
numa_emulation().
* In numa_emulation(), phys_dist must be reserved; otherwise, the new
emulated distance table may overlap it.
Fix them and, while at it, take numa_distance_cnt resetting in
numa_reset_distance() out of the if block to simplify the code a bit.
David Rientjes reported incorrect handling of distance table during
emulation.
-tj: Edited out numa_alloc_distance() related changes which weren't
necessary and rewrote patch description.
-v2: Ingo was unhappy with 80-column limit induced linebreaks. Let
lines run over 80-column.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: David Rientjes <rientjes@google.com>
This patch adds basic SandyBridge support, including hardware
cache events and PEBS events support.
It has been tested on SandyBridge CPUs with perf stat and also
with PEBS based profiling - both work fine.
The patch does not affect other models.
v2 -> v3:
- fix PEBS event 0xd0 with right umask combinations
- move snb pebs constraint assignment to intel_pmu_init
v1 -> v2:
- add more raw and PEBS events constraints
- use offcore events for LLC-* cache events
- remove the call to Nehalem workaround enable_all function
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <1299072424.2175.24.camel@localhost>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
'simple' would have required specifying current frame address
and return address location manually, but that's obviously not
the case (and not necessary) here.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4D6D1082020000780003454C@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
memblock_enforce_memory_limit() takes the desired maximum quantity of memory
to end up with, not an address above which memory will not be used.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The rtas_event_scan() function uses smp_processor_id() to select a
starting point in cpu_online_mask, and does so under the protection
of get_online_cpus(). This might not select the current processor
in any case, so switch to raw_smp_processor_id().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A number of drivers are using pgprot_writecombine() to enable write
combining on userspace mappings. Implement it on powerpc.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new functions and free the descriptor when the virq is
destroyed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Define the ARCH_IRQ_INIT_FLAGS instead of fixing it up in a loop.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Minor cleanup of notifier_from_errno() in powerpc.
notifier_from_errno() now contains the if(ret)/else conditional.
There is no need to do it in the powerpc code.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Untested, but looks like an obvious typo to me.
[BenH: No feedback, but it's obviously wrong]
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the error in spelling the config option for hw-breakpoints and fix
the build issue that follows.
Signed-off by: K.Prasad <prasad@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett points out that mpc85xx has started using the
ppc_md.machine_kexec hook. As such, revert patch c94868788c
(powerpc/kexec: Remove ppc_md.machine_kexec).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
hpte_need_flush() might be called outside of a preempt section
when manipulating the kernel page tables, so we need to use the
appopriate variants of per-cpu variable accesses. There should
be no risk of being in the middle of a batch and a context
switch will flush any pending batch.
[Patch extracted from a larger patch in Peter's preemptible
mmu_gather series]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.
* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
instances.
* apbh-dma is different between mx23 and mx28, hardware version
register is used to differentiate.
* mxs-dma supports pio function besides data transfer. The driver
uses dma_data_direction DMA_NONE to identify the pio mode, and
steals sgl and sg_len to get pio words and numbers from clients.
* mxs dmaengine has some very specific features, like sense function
and the special NAND support (nand_lock, nand_wait4ready). These
are too specific to implemented in generic dmaengine driver.
* The driver refers to imx-sdma and only a single descriptor is
statically assigned to each channel.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Ensure build doesn't silently continue despite read failure,
addressing a warning due to the unchecked call.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
LKML-Reference: <AANLkTimxxTMU3=4ry-_zbY6v1xiDi+hW9y1RegTr8vLK@mail.gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Do the notifier registration later, so we don't have to worry
about freeing it if we fail the msr allocation.
Signed-off-by: Dave Jones <davej@redhat.com>
It appears that when powernow-k8 finds that
No compatible ACPI _PSS objects found.
and suggests
Try again with latest BIOS.
it fails the module load, but does not unregister the cpu_notifier that was
registered in powernowk8_init
This ends up leaving freed memory on the cpu notifier list for some other
poor module (e.g. md/raid5) to come along and trip over.
The following might be a partial fix, but I suspect there is probably other
clean-up that is needed.
( https://bugzilla.novell.com/show_bug.cgi?id=655215 has full dmesg traces).
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
The _add_optional_clock_alias function expects an entry
already existing in the clkdev table in the form of
<dev-id=NULL, con-id=role> which might not be the case
always.
Instead, just check if an entry already exists in clkdev
in the <dev-id=dev_name, con-id=role> form, else go ahead
and add one.
Remove any assumption of an entry already existing in clkdev
table in any form.
Since this means, adding a new entry in clkdev if it does
not already exist, and not really adding an 'alias',
also rename the function name
(s/_add_optional_clock_alias/_add_optional_clock_clkdev)
to reflect this.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Sumit Semwal <sumit.semwal@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Partha Basak <p-basak2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
IVAHD and ABE power domain logic state is populated using directly
value instead of the capability flags.
Fix the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated to apply at a different point on the tree]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register naming convention for clock domain control inside
power domain instance is:
OMAPXXXX_<partition>_<power_domain>_<clock_domain>_CDOFFS
Both CPU0 and CPU1 use MPU as clock domain name instead of CPU0
and CPU1.
Change the name to stick to the convention.
The autogen scripts are updated accordingly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The git commit:
> commit a8b7458363
> Author: Ian Campbell <ian.campbell@citrix.com>
> Date: Thu Feb 17 11:04:20 2011 +0000
>
> xen: switch to new schedop hypercall by default.
>
> Rename old interface to sched_op_compat and rename sched_op_new to
> simply sched_op.
>
breaks the IA64 build. This patch fixes it.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
It now takes an additional argument so it can be used to
flush-and-invalidate pages that are cached using hash-for-home
as well those that are cached with coherence point on a single cpu.
This allows it to be used more widely for changing the coherence
point of arbitrary pages when necessary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The first is that we were using an incorrect hand-rolled variant
of __kernel_text_address() which didn't handle module PCs. We now
just use the standard API.
The second was that we weren't accounting for the three-level
page table when we were trying to pre-verify the addresses on
the 64-bit TILE-Gx processor; we now do that correctly.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This avoids having to maintain an additional separate assembly
file, and of course the inline is slightly more efficient as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we used iret to atomically return to kernel PL with
interrupts enabled. However, it turns out that we are architecturally
guaranteed that we can just set and clear the "interrupt critical
section" and only interrupt on the following instruction, so we
now do that instead, since it's cleaner.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
These headers are used by Linux but are maintained upstream.
This change incorporates a few minor fixes to these headers,
including a new sim_print() function, cleaner support for the
sim_syscall() API, and a sim_query_cpu_speed() method.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
As the added comment says, we can sometimes see a coherence warning
from our simulator if the "swapper_pgprot" variable on the boot cpu
has not been evicted from cache by the time the other cpus come up.
Force it to be evicted so we never see the warning.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This should have been as part of the initial hardwall submission to
LKML but was overlooked. The header provides the ioctl definitions for
manipulating the hardwall fd, so needs to be available to userspace.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we assumed this was impossible, but in fact it can happen.
Handle it gracefully by retrying after issuing a warning.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The problem was that this could lead to IPIs being disabled during
the softirq processing after a hypervisor downcall (e.g. for I/O),
since both IPI and device interrupts use the INCTRL_1 downcall mechanism.
When this happened at the wrong time, it could lead to deadlock.
Luckily, we were already maintaining the per-interrupt state we need,
and using it in the proper way in the hypervisor, so all we had to do
was to change Linux to stop blocking downcall interrupts for the entire
length of the downcall. (Now they're blocked while we're executing the
downcall routine itself, but not while we're executing any subsequent
softirq routines.) The hypervisor is doing a very small amount of
work it no longer needs to do (masking INTCTRL_1 on entry to the client
interrupt routine), but doing so means that older versions of Tile Linux
will continue to work with a current hypervisor, so that seems reasonable.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The current implementations of __ndelay and __udelay call a hypervisor
service to delay, but the hypervisor service isn't actually implemented
very well, and the consensus is that Linux should handle figuring this
out natively and not use a hypervisor service.
By converting nanoseconds to cycles, and then spinning until the
cycle counter reaches the desired cycle, we get several benefits:
first, we are sensitive to the actual clock speed; second, we use
less power by issuing a slow SPR read once every six cycles while
we delay; and third, we properly handle the case of an interrupt by
exiting at the target time rather than after some number of cycles.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
To handle single-step, tile mmap's a page of memory in the process
space for each thread and uses it to construct a version of the
instruction that we want to single step. If the process exec's,
though, we lose that mapping, and the kernel needs to be aware that
it will need to recreate it if the exec'ed process than tries to
single-step as well.
Also correct some int32_t to s32 for better kernel style.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The convention changed to, e.g., ".data..page_aligned". This commit
fixes the places in the tile architecture that were still using the
old convention. One tile-specific section (.init.page) was dropped
in favor of just using an "aligned" attribute.
Sam Ravnborg <sam@ravnborg.org> pointed out __PAGE_ALIGNED_BSS, etc.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moving the definition of mux setting API from devices.c to hsmmc.c
and renaming it from "omap2_mmc_mux" to "omap_hsmmc_mux".
Also calling "omap_hsmmc_mux" from omap2_hsmmc_init.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Chris Ball <cjb@laptop.org
Cc: Tony Lindgren <tony@atomide.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap3 hwmod data with the HSMMC info.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap2430 hwmod data with the HSMMC info.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC controller on the OMAP2420 is different from those
on the OMAP2430, OMAP3 and OMAP4 families - all of the latter
are identical. The one on the OMAP2420 is closer to that
on OMAP1 chips.
Currently, the n8x0 is the only OMAP2420 platform supported
in mainline which registers the MMC controller. Upcoming
changes to register the controllers using hwmod data are
potentially invasive. To reduce the risk, separate out the
2420 controller registration from the common init function
and update its only user. Also seperating out mux settings
for OMAP2420.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devices of clocks are set to usbhs, so that
only usbhs common driver can invoke these clocks.
The dummy per port clocks are added to omap3
clock data base. This helps to invoke common
clock get APIs for omap3 and omap4.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prototype and defination of functions usb_ehci_init and
usb_ohci_init are removed. The ehci and ohci devices are
removed since usbhs device contains both ehci and ohci details.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The usbhs intialization is invoked by all omap3 and omap4
variant board files.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A new usbhs platform device is defined;
this device will be the parent device of ehci and
ohci platform devices. the usbhs_init function
is defined which does the usbhs device initialization
and I/O mux of ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
enabling and disabling the common clocks for ehci
and ohci is implemented. usbhs is a common parent
platform driver for EHCI and OHCI driver. This driver
receives the clock enable and disable requests
from ehci and ohci drivers.The UHH and TLL
initialization is also performed.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already have both EHCI and OHCI there, so let's
rename to be sure everybody will understand the entire
USB HOST functionality is setup on this file.
Signed-off-by: Felipe Balbi <balbi@ti.com>
add names to EHCI and OHCI resources. That will help us
identify the resource correctly when moving to a setup
where OHCI and EHCI play well together.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is not strictly necessary but the right thing to do.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes a small memory leak that was only hit in very unlikely error
paths.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- wrong MUX was set before for IRQ
- get_pendown_state is no more needed
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The latter are error-prone because the bank number is one less than one
would read in the documentation.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Eric Benard <eric@eukrea.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch/um/Kconfig.x86 has X86_32 but not X86_64 - that's resulting in
asm/dwarf2.h producing the 32-bit (pushl_cfi & Co) macros instead of
the 64-bit ones.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Jeff Dike <jdike@addtoit.com>
LKML-Reference: <4D6CE3400200007800034498@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Powerdown the internal PHY during board init for OMAP44xx.
So that when musb is disabled core transition to retention/off
is not blocked.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the context save/restore for the control module register
used for OMAP4430 musb with UTMI embedded PHY interface.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is again current omap-for-linus branch
Adds platform initialization for working with the WLAN module
attached to the omap3evm.
The patch includes MMC2 initialization, SDIO and control pins
muxing and platform device registration.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On non-OMAP2 and non-OMAP3 kernel configs, turn omap2_sdrc_init() into
a no-op. Otherwise, compilation breaks on an OMAP4-only config with
the current omap-for-linus branch:
arch/arm/mach-omap2/built-in.o: In function `omap2_init_common_devices':
../mach-omap2/io.c:421: undefined reference to `omap2_sdrc_init'
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for suggesting the use
of a empty static inline function rather than a macro.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
[tony@atomide.com: updated not to use __init for inline omap2_sdrc_init]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix below section mismatch warning:
WARNING: vmlinux.o(.data+0x673c): Section mismatch in reference from the variable davinci_driver to the function .init.text:davinci_cpu_init()
The variable davinci_driver references
the function __init davinci_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit 6d803ba736 (ARM: 6483/1: arm & sh:
factorised duplicated clkdev.c) caused the following warnings:
In file included from /home/headless/src/kernel.org/linux-davinci/arch/arm/
include/asm/clkdev.h:17,
from include/linux/clkdev.h:15,
from arch/arm/mach-davinci/clock.h:71,
from arch/arm/mach-davinci/common.c:22:
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: `struct clk' declared
inside parameter list
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/mach-davinci/include/mach/clkdev.h:9: warning: `struct clk' declared
inside parameter list
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For DMA operation, the davinci spi driver needs an event queue number.
Currently, this number is passed as a IORESOURCE_DMA. This is not
correct, as the event queue is not a DMA channel. Pass the event queue
via the platform data structure instead.
On dm355 and dm365, move the eventq assignment for spi0 out of resources
array and into platform data.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850 uart pinmux arrays are not used. Remove them.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mmcsd0_pins pinmux array contains pins that are specific to the
da850 evm board (the write protect and card detect GPIO pins). Move
the array to the board file.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_mcasp_pins pinmux array is specific to the da850_evm, and is
not generic. Move the array to the board file, make it static initdata,
and rename it accordingly.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_emif25_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The da850_cpgmac_pins pinmux array is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For the MityDSP-L138/MityARM-1808 SoMs, the speed grade can be determined
from the part number string read from the factory configuration block on
the on-board I2C PROM. Configure the maximum CPU speed based on this
information.
This patch was tested using a MityDSP-L138 and MityARM-1808 at various
speedgrades. Also, for code coverage, a bogus configuration was tested
as well as a configuration having an unknown part number.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
From: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
The JTAG variant code for Rev-2.0 silicon of the OMAP-L138 has changed.
In addition, the variant code for the AM-1808 SoC appears to match
the Rev-2.0 code for the OMAP-L138. Add an additional entry to support
these chips.
This patch is originally from a patch on the arago project, here:
http://arago-project.org/git/projects/?p=linux-omapl1.git;a=commit;h=6157618435e313a444cdf059702bd34036a6e2b7
Further information related to the need for this patch can be located at
http://e2e.ti.com/support/embedded/f/354/p/67290/248486.aspxhttp://linux.davincidsp.com/pipermail/davinci-linux-open-source/2010-November/021224.html
This patch was tested using an AM-1808 SoC on a MityARM-1808 SoM card. It
was also tested using a Rev 1.0 silicon OMAP-L138 on a MityDSP-L138F card.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Reported-by: Nicolas Luna <luna.id@gmail.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds USB1.1 support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds USB1.1 and USB2.0 clocks for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MMC/SD support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch defines Pin Mux configuration to enable MMC/SD
and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds EDMA support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds EMAC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez <vm.rod25@gmail.com>
Tested-by: Rene Gonzalez <renegs.2378@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch fix a bug in the register indexing for GPIOs numbers > 31
to get the relevant hardware registers of tnetv107x to control the GPIOs.
In the structure tnetv107x_gpio_regs:
struct tnetv107x_gpio_regs {
u32 idver;
u32 data_in[3];
u32 data_out[3];
u32 direction[3];
u32 enable[3];
};
The GPIO hardware register addresses of tnetv107x are stored.
The chip implements 3 registers of each entity to serve 96 GPIOs,
each register provides a subset of 32 GPIOs.
The driver provides these macros: gpio_reg_set_bit, gpio_reg_get_bit
and gpio_reg_clear_bit.
The bug implied the use of macros to access the relevant hardware
register e.g. the driver code used the macro like this:
'gpio_reg_clear_bit(®->data_out, gpio)'
But it has to be used like this:
'gpio_reg_clear_bit(reg->data_out, gpio)'.
The different results are shown here:
- ®->data_out + 1 (it will add the full array size of data_out i.e. 12 bytes)
- reg->data_out + 1 (it will increment only the size of data_out i.e. only 4 bytes)
Acked-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Hirosh Dabui <hirosh.dabui@snom.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
After the multi-component commit f0fba2ad (ASoC: multi-component - ASoC
Multi-Component Support) for ASoC, we need to register the platform
device for davinci-pcm-audio.
This patch and patch at [1] are required for audio to work on
DA850/OMAP-L138.
[1] https://patchwork.kernel.org/patch/495211/
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Set up the GPTIMER hwmod used for the clockevent source immediately
before it is used. This avoids the need to set up all of the hwmods
until the boot process is further along. (In general, we want to defer
as much as possible until late in the boot process.)
This second version fixes a bug pointed out by Santosh Shilimkar
<santosh.shilimkar@ti.com>, that would cause the kernel to use an
incorrect timer hwmod name if the selected GPTIMER was not 1 or 12 -
thanks Santosh. Also, Tarun Kanti DebBarma <tarun.kanti@ti.com>
pointed out that the original patch did not apply cleanly; this has
now been fixed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Add omap_hwmod_setup_one(), which is intended for use early in boot to
selectively setup the hwmods needed for system clocksources and
clockevents, and any other hwmod that is needed in early boot.
omap_hwmod_setup_all() can then be called later in the boot process.
The point is to minimize the amount of code that needs to be run
early.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Previously, if a hwmod had already been set up, and the code attempted
to set up the hwmod again, an error would be returned. This is not
really useful behavior if we wish to allow the OMAP core code to setup
the hwmods needed for the Linux clocksources and clockevents before
the rest of the hwmods are setup. So, instead of generating errors,
just ignore the attempt to re-setup the hwmod.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Move the code that looks for the MPU initiator hwmod to run during
the individual hwmod _register() function. (Previously, it ran after
all hwmods were registered in the omap_hwmod_late_init() function.)
This is done so code can late-initialize a few individual hwmods --
for example, for the system timer -- before the entire set of hwmods is
initialized later in boot via omap_hwmod_late_init().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Migrating to clkdev has several advantages:
* Less code in mach-msm/clock.c
* A more robust clk_get() implementation
* clk_add_alias() support
* clk_get_sys() support
In general, this will help board authors setup clock aliases and
break the dependency on device pointers in the clock tables.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Not all devices use proc_comm and determining if a clock is local
vs. remote is fragile when done by comparing clk_ops pointers.
Instead, implement an is_local() function for all clk_ops to
determine if the clock is local. Doing this allows us to remove
the last references to clk_ops_pcom from clock.c and compile it
for targets with CONFIG_MSM_PROC_COMM=n.
We don't need to set the clk_ops at runtime until 7x30 local
clock detection comes in. Right now it's just complicating things
so just set the ops pointer statically.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
WARNING: vmlinux.o(.cpuinit.text+0xc80): Section mismatch in
reference from the function boot_secondary() to the variable
.init.text:msm_secondary_startup
The function __cpuinit boot_secondary() references a variable
__init msm_secondary_startup. If msm_secondary_startup is only
used by boot_secondary then annotate msm_secondary_startup with
a matching annotation.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Rename omap_hwmod_init() to omap_hwmod_register(). Rename
omap_hwmod_late_init() to omap_hwmod_setup_all(). Also change all of
the callers to reflect the new names. While here, update some
copyrights.
Suggested by Tony Lindgren <tony@atomide.com>.
N.B. The comment in mach-omap2/serial.c may no longer be correct, given
recent changes in init order.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
There's no longer any reason why we should prevent multiple
calls to omap_hwmod_init(). It is now simply used to register an
array of hwmods.
This should allow a subset of hwmods (e.g., hwmods
handling the system clocksource and clockevents) to be registered
earlier than the remaining mass of hwmods.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Some of the items removed were apparently never used, others
simply didn't get removed with their last user.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4D6BD3A002000078000341F1@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cleaning up and shortening code...
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4D6BD35002000078000341DA@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These weren't part of the initial commit of this code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4D6BCDFF02000078000341B0@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A customer of ours, complained that when setting the reset
vector back to 0, it trashed other data and hung their box.
They noticed when only 4 bytes were set to 0 instead of 8,
everything worked correctly.
Mathew pointed out:
|
| We're supposed to be resetting trampoline_phys_low and
| trampoline_phys_high here, which are two 16-bit values.
| Writing 64 bits is definitely going to overwrite space
| that we're not supposed to be touching.
|
So limit the area modified to u32.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: <stable@kernel.org>
LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes wrong constants in the hotplug assembly code for
Exynos4 such as Russell's changing in vexpress hotplug and fixes
hard-coded control register constatns also.
Reported-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds registers the s3c touchscreen and adc devices
to add touchscreen support for the gta02.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The pcf50633 regulator driver does not use the state_mem constraints,
so there is no use in setting them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Support this_cpu_cmpxchg_double() using the cmpxchg16b and cmpxchg8b
instructions.
-tj: s/percpu_cmpxchg16b/percpu_cmpxchg16b_double/ for consistency and
other cosmetic changes.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Get rid of old users of of_platform_driver in arch/sparc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Get rid of old users of of_platform_driver in arch/powerpc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
arch/powerpc/kernel/ibmebus.c is the only remaining user of the
of_bus_type support code for initializing the bus and registering
drivers. All others have either been switched to the vanilla platform
bus or already have their own infrastructure.
This patch moves the functionality that ibmebus is using out of
drivers/of/{platform,device}.c and into ibmebus.c where it is actually
used. Also renames the moved symbols from of_platform_* to
ibmebus_bus_* to reflect the actual usage.
This patch is part of moving all of the of_platform_bus_type users
over to the platform_bus_type.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Note that the hardware schematics and documentations can be obtained
here: http://www.bugcommunity.com/wiki/index.php/BUGbase
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to fix the warning below.
arch/arm/configs/mx51_defconfig:113:warning: symbol value 'm' invalid for LEDS_CLASS
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows the regulator core to disable all regulators
which are not in use at the end of the kernel init phase.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The REGULATOR_CHANGE_STATUS flag needs to be set on valid_ops_mask,
otherwise it a driver wont be able to turn the regulator on or off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for the two buttons found on the gta02 device,
which are connectd to gpio pins, using the gpio-keys driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ASoC multi-component patch introduced a new pcm platform device,
which needs to be registered by board files in order for sound to work.
This patch does this for the gta02 board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since f0fba2ad1b it's required to register platform devices even for
AC'97 codecs. Register one on tosa (wm9712-codec).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa25x platforms were left out of major ASoC Update patch.
Since f0fba2ad1b a registration of pxa-pcm-audio device is required for
ASoC to function on pxa platforms. Register one also for pxa210/pxa25x.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since 2e48928d8a it's no longer possible to set
the name of the LED trigger for RFKILL events. Drop respective code from tosa-bt.c
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The Cortex-A9 tile on the Versatile Express suffers from a number of
engineering errata.
This patch selects workarounds in the ARCH_VEXPRESS_CA9X4 Kconfig entry
so that users don't need to worry about which ones to apply.
Reported-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We currently presume a 4x expansion to guess the decompressed kernel size
in order to determine if the decompressed kernel is in conflict with
the location where zImage is loaded. This guess may cause many issues
by overestimating the final kernel image size:
- This may force a needless relocation if the location of zImage was
fine, wasting some precious microseconds of boot time.
- The relocation may be located way too far, possibly overwriting the
initrd image in RAM.
- If the kernel image includes a large already-compressed initramfs image
then the problem is even more exacerbated.
And if by some strange means the 4x guess is too low then we may overwrite
ourselves with the decompressed image.
So let's use the exact decompressed kernel image size instead. For that
we need to rely on the stat command, but this is hardly a new build
dependency as the kernel already depends on many external commands
to be built provided by the coreutils package where stat is found.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S5P6442 and S5PC100 SoCs have 4 VICs. However, default VIC number
is defined 2 in arch/arm/common. So can be happened some problem on it.
Basically, it requires for suspend and resume.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S5PV210 SoC have 4 VICs. It requires for suspend and resume.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Loading Thumb-2 modules into an ARM kernel or vice-versa isn't
guaranteed to work safely, since the kernel is not interworking-
aware everywhere.
This patch adds "thumb2" to the module vermagic when
CONFIG_THUMB2_KERNEL is enabled, to help avoid accidental loading
of modules into the wrong kernel.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv7 allows the debug core logic to be powered down and provides the
DBGPRSR register so that software can power-up and check the status of
the logic.
This patch ensures that the debug logic is powered up on ARMv7 cores
before we attempt to access the extended debug registers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GETHBPREGS ptrace request incorrectly maps its index argument onto
the thread's saved debug state when the index != 0. This has not yet
been seen from userspace because GDB (the only user of this request)
only reads from register 0.
This patch fixes the indexing.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 6fc31d54 this comment is no longer true.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PAGE_SIZE_asm, PAGE_SHIFT_asm, THREAD_SIZE_asm can be safely removed from
asm-offsets.c, and be replaced by their non-'_asm' counterparts in the code
that uses them, since the _AC macro defined in include/linux/const.h makes
PAGE_SIZE/PAGE_SHIFT/THREAD_SIZE work with as.
Signed-off-by: Stratos Psomadakis <psomas@cslab.ece.ntua.gr>
LKML-Reference: <1298666774-17646-2-git-send-email-psomas@cslab.ece.ntua.gr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Disable autoidle on all clocks during clock framework initialization.
(If CONFIG_PM is set, autoidle is re-enabled for all clocks later in
the boot process.)
The principle behind this patch, and some similar patches, is that the
kernel should start with all power management features disabled.
Later in the boot process, the PM code, if compiled in with CONFIG_PM,
enables or re-enables power management features.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Enable hardware gate control for all dpll MX and X2 postdividers.
This requires the allow_idle/deny_idle functions to be
populated for all clock nodes (mx/x2 post dividers) in
clkops.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, the dpll post divider outputs (MX outputs)
along with clockout_x2 output provide a way to allow/deny
hardware level autogating.
Allowing autoidle would mean that the hw would autogate
this clock when there is no dependency for it.
Denying idle would mean that this clock output will be
forced to stay enabled.
Add dpll api's to read/allow/deny idle control
for these dpll mx postdividers.
NOTE: The gatectrl bit set to 0 allows gatectrl,
and the bit set to 1 denies gatectrl.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: moved OMAP4-specific DPLL control code to
mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Attempt to enable autoidle for as many clocks as possible in the
OMAP2+-common CONFIG_OMAP_RESET_CLOCKS code. Currently, this only
enables DPLL autoidle for OMAP3/4 DPLLs; but future patches will
enable autoidle for other clocks and the OMAP2 DPLL/APLLs.
In the long run, we should probably get rid of
CONFIG_OMAP_RESET_CLOCKS, and unconditionally run the code that it
selects. Otherwise, the state of the clock tree won't match the
hardware state - this could result in clocks being enabled or disabled
unpredictably.
Based on a patch by Rajendra Nayak <rnayak@ti.com> that did this in
the pm34xx.c/pm44xx.c code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
All OMAP3/4 dpll's support hardware level autogating.
Populate allow_idle/deny_idle function pointers for all
DPLL's in clkops.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP various clock nodes (dpll's, mx post dividers, interface clocks)
support hardware level autogating which can be controlled from
software.
Support such functionality by adding two new function pointer
allow_idle and deny_idle in the clkops structure.
These function pointers can be populated for any clock
node which supports hardware level autogating.
Also add 2 new functions (omap_clk_enable_autoidle_all and
omap_clk_disable_autoidle_all) which can be called from
architecture specific PM core code, if hardware level
autogating (for all supported clock nodes) is to be
enabled or disabled.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use spinlock rather than mutex due to race; renamed functions;
functions now return ints]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL1 on omap3 is very similar to the rest of
the non-core dpll's.
Hence populate clkops_omap3_noncore_dpll_ops
as the clkops for it, instead of the
currently populated clkops_null.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Check if enable/disable operations are supported for a given
clock node before attempting to call them.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that wkup and sleep dependencies are supported (in the
form of static deps) for OMAP4, remove all instances of
pr_errs' stating dependencies are still unsupported
on OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add OMAP4 platform specific implementation to support clkdm
wkup and sleep dependencies a.k.a static dependencies.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: removed comment about PRM; zero-prefixed STATICDEP
register offset; fixed loop termination condition in
omap4_clkdm_clear_all_wkup_sleep_deps(); thanks to Kevin Hilman for finding
and helping fix this bug]
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add new OMAP4 CM accesor apis to set/clear and read
bitfields (based on mask) from CM registers.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 supports static dependencies and dynamic dependencies
between clock domains. Static dependencies imply both
wakeup as well as sleep dependencies.
Generate all clockdomain static dependency sources.
(Dynamic dependency sources are hardwired and
cannot to controlled from software).
The autogen scripts are updated to generate the contents
of this patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_clk_enable
.clkdm_clk_disable
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_k_enable as clkdm_clk_enable and
omap2_clkdm_clk_disable as clkdm_clk_disable.a
Remove unused functions (_enable/_disable_hwsup) and unsed
headers from clockdomain.c file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_allow_idle
.clkdm_deny_idle
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_allow_idle as clkdm_allow_idle and
omap2_clkdm_deny_idle as clkdm_deny_idle.
Make the _clkdm_add_autodeps and _clkdm_del_autodeps as non-static
so they can be accessed from OMAP2/3 platform specific code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_sleep
.clkdm_wakeup
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_wakeup as clkdm_wakeup and
omap2_clkdm_sleep as clkdm_sleep.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed omap3_clkdm_clear_all_sleepdeps() and
omap2_clkdm_clear_all_wkdeps() to test against the correct
loop termination condition; thanks to Kevin Hilman for finding and
helping fix]
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3
.clkdm_add_wkdep
.clkdm_del_wkdep
.clkdm_read_wkdep
.clkdm_clear_all_wkdeps
.clkdm_add_sleepdep
.clkdm_del_sleepdep
.clkdm_read_sleepdep
.clkdm_clear_all_sleepdeps
Convert the platform-independent framework to call these functions.
With this also move the clkdm lookups for all wkdep_srcs and
sleepdep_srcs at clkdm_init.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed loop termination conditions in omap*_clkdm_clear_all_*();
thanks to Kevin Hilman for finding and helping fix those bugs; also
avoid re-resolving clockdomains during init; abstracted out clkdm_dep walk]
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Put infrastructure in place, so arch specific func pointers
can be hooked up to the platform-independent part of the
framework.
This is in preparation of splitting the clockdomain framework into
platform-independent part (for all omaps) and platform-specific
parts.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Trivial fix to remove the unused function declaration
from the powerdomain header.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 quirk: Fix polarity for IRQ0 pin2 override on SB800 systems
x86/mrst: Fix apb timer rating when lapic timer is used
x86: Fix reboot problem on VersaLogic Menlow boards
CPU0 and CPU1 clockdomain is at the offset of 0x18 from the LPRM base.
The header file has set it wrongly to 0x0. Offset 0x0 is for CPUx power
domain control register
Fix the same.
The autogen scripts is fixed thanks to Benoit Cousson
With the old value, the clockdomain code would access the
*_PWRSTCTRL.POWERSTATE field when it thought it was accessing the
*_CLKSTCTRL.CLKTRCTRL field. In the worst case, this could cause
system power management to behave incorrectly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: added second paragraph to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
init_early hook runs too early for omap3_mux_init(), so the board
won't boot. Moved to init_machine, then it works just fine.
Signed-off-by: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add SI4713 FM transmitter supplies, platform data and setup to RX-51/N900.
It is connected to line output signals of TLV320AIC34 codec A part.
Driver can be either built-in or a module. It can be tuned with v4l2-ctl
from ivtv-utils. Following examples illustrate the use of it:
v4l2-ctl -d /dev/radio0 --set-ctrl=mute=0 (power up)
v4l2-ctl -d /dev/radio0 -f 107900 (tune 107.9 MHz)
v4l2-ctl -d /dev/radio0 --set-ctrl=mute=1 (power down)
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
xen_pre_device_suspend is unused on ia64.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Rename old interface to sched_op_compat and rename sched_op_new to
simply sched_op.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Take the opportunity to comment on the semantics of the PV guest
suspend hypercall arguments.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Initialize PV spinlocks on boot CPU right after native_smp_prepare_cpus
(that switch to APIC mode and initialize APIC routing); on secondary
CPUs on CPU_UP_PREPARE.
Enable the usage of event channels to send and receive IPIs when
running as a PV on HVM guest.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Up to now we force enable the local apic in the devicetree setup
uncoditionally and set smp_found_config unconditionally to 1 when a
devicetree blob is available. This breaks, when local apic is disabled
in the Kconfig.
Make it consistent by initializing device tree explicitely before
smp_get_config() so a non lapic configuration could be used as well.
To be functional that would require to implement PIT as an interrupt
host, but the only user of this code until now is ce4100 which
requires apics to be available. So we leave this up to those who need
it.
Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds the volatile cast which forces the compiler to emit the load.
Suggested by Peter Zijlstra <peterz@infradead.org>.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
numa_distance should be sized like the SLIT, an NxN matrix where N is
the highest node id + 1. This patch fixes the calculation to avoid
overflowing the array on the subsequent iteration.
-tj: The original patch used last index to calculate size. Yinghai
pointed out it should be incremented so it is the number of
elements instead of the last index to calculate the size of the
table. Updated accordingly.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
SAL requires that interrupts be enabled when making some calls
to it to pick up error records, so we enable interrupts inside
this handler. We should disable them again at the end.
Found by a new WARN_ONCE that tglx added to handle_irq_event_percpu()
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add support to register an isr for IOMMU fault situations and adapt it
to allow such (*isr)() to be used as fault callback. Drivers using IOMMU
module might want to be informed when errors happen in order to debug it
or react.
Signed-off-by: David Cohen <dacohen@gmail.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IOMMU upper layer and user are responsible to handle a fault and to
define whether it will end up as an error or not. OMAP2+ specific
layer should not print anything in such case.
Signed-off-by: David Cohen <dacohen@gmail.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Information like base address and DMA channel nubers should no longer
be obtained using macros. These information should be obtained from
hwmod database. Hence the macros that define the base address are removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After McBSP driver is hwmod adapted, the information about the hw would be
obtained from the hwmod database by the mcbsp driver. Since DMA programming is
handled by the client driver, APIs are provided to pass the DMA channel number
and base address of data register required by the client driver for DMA
programming.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm runtime support for McBSP driver.
Reference to fclk is not removed because it is required when the
functional clock is switched from one source to another.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2/3 in OMAP3 has sidetone feature which requires autoidle
to be disabled before starting the sidetone. Also SYSCONFIG
register has to be set with smart idle or no idle depending on the
dma op mode (threshold or element sync). For doing these operations
dynamically at runtime, omap_device APIs are used to modify SYSCONFIG register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[tony@atomide.com: updated to compile without omap_device idle calls]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modify OMAP2+ McBSP to use omap hwmod framework APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the sidetone block is tightly coupled to the mcbsp, sidetone information
is directly added to mcbsp2 & 3 hwmod dev_attr.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added a name to address space belonging to SDMA and MPU facilitating
the driver to get the address space info by name. Added a revision
member inorder to facilitate the driver to differentiate between
mcbsp in different omap.
Also added a platform_get_irq in probe to get irq number by index since
from OMAP4, there will be a single irq line.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add McBSP hwmod data for OMAP3.
Added a revision member inorder to facilitate the driver to
differentiate between mcbsp in different omap.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add McBSP hwmod data for OMAP2430.
Added a revision member inorder to facilitate the driver to
differentiate between mcbsp in different omap.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add McBSP hwmod data for OMAP2420.
Also add macros in prcm-common.h for idlest bit of OMAP24XX McBSP devices
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement McBSP as platform device and add support for
registering through platform device layer using resource
structures.
Later in this patch series, OMAP2+ McBSP driver would be modified to
use hwmod framework after populating the omap2+ hwmod database.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds support for resource API to get address space info other than just MPU.
The drivers can now use platform_get_resource_byname() to get resource of
type 'IORESOURCE_MEM' by name.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use runtime pm APIs to enable/disable mailbox clocks and
to configure SYSC register.
Based on the patch sent by Felipe Contreras:
https://patchwork.kernel.org/patch/101662/
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove static platform_device and resource data within
omap mailbox driver; use the one defined in the hwmod
database along with omap_device framework for device
build and registration.
Add device latency functions to be used, so clock can be
enabled and sysconfig is configured.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mailbox hwmod data for omap3.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP IOMMU generic layer doesn't need ot print function name during
error messages. Print module name instead which is more useful.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In a modular build of the iommu code it's possible that the arch iommu code
isn't loaded when trying to enable the iommu. Instead of blindly following a
null pointer return -NODEV in that case.
Signed-off-by: Martin Hostettler <martin@neutronstar.dyndns.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2+ kernels built without CONFIG_OMAP_32K_TIMER crash on boot after the
2.6.38 sched_clock changes:
[ 0.000000] OMAP clockevent source: GPTIMER1 at 13000000 Hz
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 80000005 [#1] SMP
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (2.6.38-rc5-00057-g04aa67d #152)
[ 0.000000] PC is at 0x0
[ 0.000000] LR is at sched_clock_poll+0x2c/0x3c
Without CONFIG_OMAP_32K_TIMER, the kernel has an clockevent and
clocksource resolution about three orders of magnitude higher than
with CONFIG_OMAP_32K_TIMER set. The tradeoff is that the lowest
power consumption states are not available.
Fix by calling init_sched_clock() from the GPTIMER clocksource init code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On some SB800 systems polarity for IOAPIC pin2 is wrongly
specified as low active by BIOS. This caused system hangs after
resume from S3 when HPET was used in one-shot mode on such
systems because a timer interrupt was missed (HPET signal is
high active).
For more details see:
http://marc.info/?l=linux-kernel&m=129623757413868
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org # 37.x, 32.x
LKML-Reference: <20110224145346.GD3658@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function do_suspend_lowlevel() is specific to x86 and defined in
assembly code, so it should be called from the x86 low-level suspend
code rather than from acpi_suspend_enter().
Merge do_suspend_lowlevel() into the x86's acpi_save_state_mem() and
change the name of the latter to acpi_suspend_lowlevel(), so that the
function's purpose is better reflected by its name.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
e820_table_{start|end|top}, which are used to buffer page table
allocation during early boot, are now derived from memblock and don't
have much to do with e820. Change the names so that they reflect what
they're used for.
This patch doesn't introduce any behavior change.
-v2: Ingo found that earlier patch "x86: Use early pre-allocated page
table buffer top-down" caused crash on 32bit and needed to be
dropped. This patch was updated to reflect the change.
-tj: Updated commit description.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Both OLPC and CE4100 activate CONFIG_OF. OLPC uses PROMTREE while CE
uses FLATTREE. Compiling for OLPC only breaks due to missing flat tree
functions and variables.
Use proper wrappers and provide an empty x86_flattree_get_config()
inline so OF=y FLATTREE=n builds and works.
[ tglx: Make it work with HPET_TIMER=n and make a function static ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Need to adjust the clockevent device rating for the structure
that will be registered with clockevent system instead of the
temporary structure.
Without this fix, APB timer rating will be higher than LAPIC
timer such that it can not be released later to be used as the
broadcast timer.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
LKML-Reference: <1298506046-439-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds definitions for power consumers for s3c-hsotg driver
on Goni board. The consumers are defined as arrays, because later more
entries for MIPI and ADC will be defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A lot of power regulator has been enabled by default causing the board
to consume a lot of power. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
tegra_dma_init currently simply bails out early if any initialization fails.
This skips various data-structure initialization. In turn, this means that
tegra_dma_allocate_channel can still hand out channels. In this case, when
tegra_dma_free_channel is called, which calls tegra_dma_cancel, the walking
on ch->list will OOPS since the list's next/prev pointers may still be
NULL.
To solve this, add an explicit "initialized" flag, only set this once _init
has fully completed successfully, and have _allocate_channel refuse to hand
out channels if this is not set.
While at it, simplify _init:
* Remove redundant memsets
* Use bitmap_fill to mark all channels as in-use up-front, and remove
some now-redundant bitmap initialization loops.
* Only mark a channel as free once all channel-related initialization has
completed.
Finally, the successful exit path from _init always has ret==0, so just
hard-code that return. The error path still returns ret.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The ASoC machine driver was written assuming my previous patch to add
complete support for these clocks, which named them cdev1/2. Rename
the clocks to match that, to avoid churn in the ASoC driver.
This rename also makes the clocks more consistent with other Tegra
clocks irrespective of any of that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The driver is tegra-i2s not just i2s. Rename the clocks to match, so that
clk_get_sys can look up by driver name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The following commit makes the Tegra APB DMA engine fail to initialize
correctly: 0cf6230af9
ARM: tegra: Move tegra_common_init to tegra_init_early
The reason is that tegra_init_early_ calls tegra_dma_init which calls
request_threaded_irq, which fails since the IRQ hasn't yet been marked
valid; that only happens in tegra_init_irq, which gets called after
tegra_init_early.
This used to work OK, since tegra_init_early was tegra_common_init, which
got called after tegra_init_irq, basically from the beginning of
tegra_harmony_init.
Solve this by converting tegra_dma_init to a postcore_initcall. This makes
it execute late enough that IRQs are marked valid, and avoids having to
add it back to every machine's init function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
This allows to load the OF driver based informations from the device
tree. Systems without BIOS may need to perform some initialization.
PowerPC creates a PNP device from the OF information and performs this
kind of initialization in their private PCI quirk. This looks more
generic.
This patch also avoids registering the platform RTC driver on X86 if
we have a device tree blob. Otherwise we would setup the device based
on the hardcoded information in arch/x86 rather than the device tree
based one.
[ tglx: Changed "int of_have_populated_dt()" to bool as recommended by
Grant ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
Cc: rtc-linux@googlegroups.com
Cc: Alessandro Zummo <a.zummo@towertech.it>
LKML-Reference: <1298405266-1624-12-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use device tree information to setup IO_APIC configuration, interrupt
routing, HPET and everything else which cannot be enumerated by other
means.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-11-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ioapic_xlate provides a translation from the information in device tree
to ioapic related informations. This includes
- obtaining hw irq which is the vector number "=> pin number + gsi"
- obtaining type (level/edge/..)
- programming this information into ioapic
ioapic_add_ofnode adds an irq_domain based on informations from the device
tree. This information (irq_domain) is required in order to map a device to
its proper interrupt controller.
[ tglx: Adapted to the io_apic changes, which let us move that whole code
to devicetree.c ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-10-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For now we probe these busses and we change this to board dependent
probes once we have to.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-9-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86_of_pci_init() does two things:
- it provides a generic irq enable and disable function. enable queries
the device tree for the interrupt information, calls ->xlate on the
irq host and updates the pci->irq information for the device.
- it walks through PCI bus(es) in the device tree and adds its children
(device) nodes to appropriate pci_dev nodes in kernel. So the dtb
node information is available at probe time of the PCI device.
Adding a PCI bus based on the information in the device tree is
currently not supported. Right now direct access via ioports is used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-8-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Set hpet_address based on information provied form DTB
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
LKML-Reference: <1298405266-1624-7-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
APIC and IO_APIC have to be added to the system early because
native_init_IRQ() requires it.
In order to obtain the address of the ioapic the device tree has to be
unflattened so of_address_to_resource() works.
The device tree is relocated to ensure it is always covered by the
kernel mapping. That way the boot loader does not have to make
any assumptions about kernel's memory layout.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
LKML-Reference: <1298405266-1624-6-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The here introduced irq_domain abstraction represents a generic irq
controller. It is a subset of powerpc's irq_host which is going to be
renamed to irq_domain and then become generic. This implementation will
be removed once it is generic.
The xlate callback is resposible to parse irq informations like irq type
and number and returns the hardware irq number which is reported by the
hardware as active.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-5-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
History:
v1..v2:
- dropped device_type except for cpu & pci. I have the compatible string
for pci so I can drop the device_type once it is possible
- I lowercased all compatible types. I will need to resend some patches
which have upper case intel
- The cpu had the same compatible string as the soc node. So I added to
the soc node -immr for internel memory mapped registers.
- I added generic names for all parts.
- I reworked the i2c bars matching the way you suggested. I added a
compatible node for the PCI device which only the PCI ids in its
compatible string. The bars (each represents a complete i2c
controller) have a "intel,ce4100-i2c-controller" compatible node. It
is not used by the driver.
The driver is probed via PCI ids (by the pci subsystem not OF) and
matches the bar address against the ressource in the child node. Once
there is a hit the node is attached.
- The SPI driver is also probed via pci. However I also attached a
compatible property based on PCI ids
v2..v3:
- intel,ce4100-immr become intel,ce4100-cp. cp stands for core
peripherals. The Atom data sheet talks here about ACPI devices. Since
we don't have ACPI this does not apply here.
- The interrupt map is gone. There are now plenty of device nodes.
- The "unit address string" got fixed, it uses not DD,V format.
v3..v4:
- added descriptions for compatible nodes introduced here:
- intel,ce4100-ioapic
- intel,ce4100-lapic
- intel,ce4100-hpet
- intel,ce4100
- intel,ce4100-cp
- intel,ce4100-pci
- added a description about I2C controller magic.
- Added gpio-controller and gpio-cells property to gpio devices. Those
properties are not (yet) used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-4-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds minimal support for device tree on x86. The device
tree blob is passed to the kernel via setup_data which requires at
least boot protocol 2.09.
Memory size, restricted memory regions, boot arguments are gathered
the traditional way so things like cmd_line are just here to let the
code compile.
The current plan is use the device tree as an extension and to gather
information which can not be enumerated and would have to be hardcoded
otherwise. This includes things like
- which devices are on this I2C/SPI bus?
- how are the interrupts wired to IO APIC?
- where could my hpet be?
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-3-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch ensures that the memory passed from parse_setup_data() is
large enough to cover the complete data structure. That means that the
conditional mapping in parse_e820_ext() can go.
While here, I also attempt not to map two pages if the address is not
aligned to a page boundary.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-2-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tile's __pte_free_tlb() implementation makes assumptions about the
generic mmu_gather implementation, cure this ;-)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
io_apic_set_pci_routing() and mp_save_irq() check the pin_programmed
bit before calling io_apic_setup_irq_pin() and set the bit when the
pin was setup.
Move that duplicated code into a separate function and use it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On OMAP4430 ES1.0 the local timers are gated by security. Enable the
CONFIG_LOCAL_TIMERS for omap2plus build and handle the OMAP4430 es1.0
exception case.
This patch has dependency on the first patch in this series.
ARM: smp: Select local timers vs dummy timer support runtime
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current code support of dummy timers in absence of local
timer is compile time. This is an attempt to convert it to runtime
so that on few SOC version if the local timers aren't supported
kernel can switch to dummy timers. OMAP4430 ES1.0 does suffer from
this limitation.
This patch should not have any functional impact on affected
files.
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the case of a conflict between the memory used by the compressed
kernel with its decompressor code and the memory used for the
decompressed kernel, we currently store the later after the former and
relocate it afterwards.
This would be more efficient to do this the other way around i.e.
relocate the compressed data up front instead, resulting in a smaller
copy. That also has the advantage of making the code smaller and more
straight forward.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PTRACE_SINGLESTEP is a ptrace request designed to offer single-stepping
support to userspace when the underlying architecture has hardware
support for this operation.
On ARM, we set arch_has_single_step() to 1 and attempt to emulate hardware
single-stepping by disassembling the current instruction to determine the
next pc and placing a software breakpoint on that location.
Unfortunately this has the following problems:
1.) Only a subset of ARMv7 instructions are supported
2.) Thumb-2 is unsupported
3.) The code is not SMP safe
We could try to fix this code, but it turns out that because of the above
issues it is rarely used in practice. GDB, for example, uses PTRACE_POKETEXT
and PTRACE_PEEKTEXT to manage breakpoints itself and does not require any
kernel assistance.
This patch removes the single-step emulation code from ptrace meaning that
the PTRACE_SINGLESTEP request will return -EIO on ARM. Portable code must
check the return value from a ptrace call and handle the failure gracefully.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move L1_CACHE_SHIFT related options together, rather than spreading them
across two separate Kconfig files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some installers would binary patch the kernel zImage to replace the
first few nops with custom instructions. This breaks the Thumb2 kernel
as the mode switch is right at the beginning. Let's move it towards the
end of the nop sequence instead.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Improve the documentation for the VFP hotplug notifier handler, so
that people better understand what's going on there and what has
been done for them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In commit e616c59140, highmem support was
deactivated for SMP platforms without hardware TLB ops broadcast because
usage of kmap_high_get() requires that IRQs be disabled when kmap_lock
is locked which is incompatible with the IPI mechanism used by the
software TLB ops broadcast invoked through flush_all_zero_pkmaps().
The reason for kmap_high_get() is to ensure that the currently kmap'd
page usage count does not decrease to zero while we're using its
existing virtual mapping in an atomic context. With a VIVT cache this
is essential to do due to cache coherency issues, but with a VIPT cache
this is only an optimization so not to pay the price of establishing a
second mapping if an existing one can be used. However, on VIPT
platforms without hardware TLB maintenance we can give up on that
optimization in order to be able to use highmem.
From ARMv7 onwards the TLB ops are broadcasted in hardware, so let's
disable ARCH_NEEDS_KMAP_HIGH_GET only when CONFIG_SMP and
CONFIG_CPU_TLB_V6 are defined.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Saeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This cleans up after the conversion to irq_data. Rename the function
to match the method, and remove the now useless lookup of the irq
descriptor which is never used. Move the bitmask calculation out of
the irq_controller_lock region.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure appropriate locks are taken to ensure that IRQ migration off
the current CPU is race-free. We may have a concurrent set_affinity
via procfs running on another CPU in parallel with the IRQ migration,
resulting in unpredictable results.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The force argument to irq_set_affinity really should be 'true' as
moving IRQs off a CPU which is going down isn't optional.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a missing call to pci_enable_bridges() so that devices behind
bridges get found by the pci bus scan.
Signed-off-by: Chris Partington <chris.partington@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current diagnostics are rather poor when things go wrong:
ipv6: relocation out of range, section 2 reloc 0 sym 'snmp_mib_free'
Let's include a little more information about the problem:
ipv6: section 2 reloc 0 sym 'snmp_mib_free': relocation 28 out of range (0xbf0000a4 -> 0xc11b4858)
so that we show exactly what the problem is - not only what type of
relocation but also the offending address range too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have 'install' and 'zinstall' for installing Image and zImage
kernels, so add 'uinstall' to complete the set.
This allows developers to have a ~/bin/installkernel script which (eg)
copies the kernel to the tftp server automatically once the kernel
has built, resulting in a better workflow.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/return_address.c:37:6: warning: symbol 'return_address' was not declared. Should it be static?
arch/arm/kernel/setup.c:76:14: warning: symbol 'processor_id' was not declared. Should it be static?
arch/arm/kernel/traps.c:259:1: warning: symbol 'die_lock' was not declared. Should it be static?
arch/arm/vfp/vfpmodule.c:156:6: warning: symbol 'vfp_raise_sigfpe' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Achieve better usage of the DMA coherent region by doing top-down
allocation rather than bottom up. If we ask for a 128kB allocation,
this will be aligned to 128kB and satisfied from the very bottom
address. If we then ask for a 600kB allocation, this will be aligned
to 1MB, and we will have a 896kB hole.
Performing top-down allocation resolves this by allocating the 128kB
at the very top, and then the 600kB can come in below it without any
unnecessary wastage.
This problem was reported by Janusz Krzysztofik, who had 2 x 128kB +
1 x 640kB allocations which wouldn't fit into 1MB.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no point to have irq_trigger() and irq_polarity() as wrappers
around the MPBIOS_* camel case functions. Get rid of both the inlines
and the ugly camel case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The only difference here is that we did not call
__add_pin_to_irq_node() for the legacy irqs, but that's not worth 30
lines of extra code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the duplicated code and call the function. It does not matter
whether we allocated the cfg before calling setup_local_APIC() and we
can set the irq chip and handler after that as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are about four places in the ioapic code which do exactly the
same setup sequence. Also the OF based ioapic setup needs that
function to avoid putting the OF specific code into ioapic.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Two consecutive
for(...)
for(...)
lines to avoid an extra indentation are just horrible to read. I had
to look more than once to figure out what the code is doing.
Split out the inner loop into a separate function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is debug code and it does not matter at all whether we print each
not connected pin in an extra line or try to be extra clever.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit
06824ba (ARM: tlb: delay page freeing for SMP and ARMv7 CPUs)
introduced a build failure for builds with CONFIG_SWAP=n:
In file included from arch/arm/mm/init.c:27:
arch/arm/include/asm/tlb.h: In function 'tlb_flush_mmu':
arch/arm/include/asm/tlb.h:101: error: implicit declaration of function 'release_pages'
arch/arm/include/asm/tlb.h: In function 'tlb_remove_page':
arch/arm/include/asm/tlb.h:165: error: implicit declaration of function 'page_cache_release'
as linux/swap.h doesn't include linux/pagemap.h but actually needs it
(see comments in linux/swap.h as to why this is.)
Fix that by #including <linux/pagemap.h> in <asm/pgalloc.h> as it's done
by x86.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The initial MMU table created in head.S contains a 1 MB mapping at the
start of memory to let the early kernel boot code access the boot params
specified by mdesc->boot_params.
When using CONFIG_ARM_PATCH_PHYS_VIRT it is possible for the kernel to
have a different idea of where the start of memory is at run time, making
the compile-time determined mdesc->boot_params pointing to a memory area
which is not mapped. Any access to the boot params in that case will
fault and silently hang the kernel at that point. It is therefore a
better idea to simply ignore mdesc->boot_params in that case and give
the kernel a chance to print some diagnostic on the console later.
If the bootloader provides a valid pointer in r2 to the kernel then this
is used instead of mdesc->boot_params, and an explicit mapping is already
created in the initial MMU table for it. It is therefore a good idea to
use that facility when using a relocated kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 6fc31d54 there is no callers for lookup_machine_type()
other than setup_machine(). And if the former fails it won't return,
therefore the error path in the later is dead code. Let's clean
things up by merging them together.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __param section is already brought in by RODATA above.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 7cd92366a5
lAPIC enabled accidently the IOAPIC, which now gets fixed.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
LKML-Reference: <1298385487-4708-5-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds IOAPIC dummy functions for compilation
with local APIC, but without IOAPIC.
The local variable ioapic_entries in enable_IR_x2apic()
does not need initialization anymore, since the dummy
returns NULL.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
LKML-Reference: <1298385487-4708-4-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently arch_disable_smp_support() on x86 disables only the
support for the IOAPIC and is also compiled in if SMP-support is
not.
Therefore this function is renamed to disable_ioapic_support(),
which meets its purpose and is only compiled in the kernel
when IOAPIC support is also.
A new arch_disable_smp_support() is created in smpboot.c,
which calls disable_ioapic_support() and gets only compiled
in the kernel when SMP support is also.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
LKML-Reference: <1298385487-4708-3-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a dummy function, used when no IOAPIC is compiled in.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
LKML-Reference: <1298385487-4708-2-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This enum is used by non IOAPIC code, so apicdef.h is
the best place for it.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
LKML-Reference: <1298385487-4708-1-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
OLPC_OPENFIRMWARE_DT is just there to be selected by OLPC and selects
OF_PROMTREE. So let OLPC select OF_PROMTREE and remove that extra
config indirection. Fixup code and Makefile and use CONFIG_OF_PROMTREE
instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andres Salomon <dilinger@queued.net>
Neither CONFIG_OLPC_OPENFIRMWARE nor CONFIG_OLPC_OPENFIRMWARE_DT are
really necessary.
OLPC selects OLPC_OPENFIRMWARE unconditionally, so move the "select
OF" part under OLPC config option and fixup the dependencies in
Makefiles and code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andres Salomon <dilinger@queued.net>
OLPC selects OLPC_OPENFIRMWARE unconditionally. If OLPC=n then
the OLPC_OPENFIRMWARE functionality is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andres Salomon <dilinger@queued.net>
Reason: Import mainline device tree changes on which further patches
depend on or conflict.
Trivial conflict in: drivers/spi/pxa2xx_spi_pci.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch updated board files to replace platform_device_register or
platform_add_devices of DSS with omap_display_init(). This moves away
registration of DSS from board files into a common place.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A new file display.c is introduced for display driver init, which adds a function
omap_display_init to do the DSS driver registration. This is the first step in moving
away registration of DSS from board files into a common place.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use driver name in regulator inits needed for display instead of using device
structure name.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for Display Sub System applicable for OMAP3430 and
OMAP36xx. DSS is also considered as an IP as DISPC, RFBI and named as dss_core.
For all the IP modules in DSS, same clock is needed for enabling. Hwmod sees
DSS IPs as independent IPs, so same clock has to be repeated for .main_clk in
each IP.
This patch defines separate hwmod databases for OMAP3430ES1 and (OMAP3430ES2 and
OMAP36xx) as OMAP3430ES1 does not have IDLEST bit to poll on for dss IP, and also
the firewall regions are different between 3430es1 and later.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2430 Display Sub System. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2420 Display Sub System,. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP35X TRM Rev 2010-05 Figure 7-18 "DPLL With EMI Reduction
Feature", it is shown that the internal frequency is calculated by
CLK_IN/(N+1). However, the value passed to _dpll_test_fint() is
already "N+1" since Linux is using the values to divide by. In the
technical reference manual, "N" is referring to the divider's register
value (0-127).
During power management testing, it was observed that programming the
wrong jitter correction value can cause the system to become unstable
and eventually crash.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
[paul@pwsan.com: added second paragraph to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This adds board support for the Seaboard eval platform and some of the
derivatives that are very similar. Since they only differ in some very
minor ways, most of the code is shared.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Turns out MMC2 (the bayonet 4-lane port) wasn't enabled in the
original pinmux. Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add the 3 sdhci devices that are available on Harmony as
platform devices. Two go to slots (one 4-lane, one 8-lane),
and one goes to onboard wifi.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add a common location to register resources for used on-chip devices
that are commonly configured on boards. Devices will be added to this file
as more drivers are added that can make use of them.
This is based on work contributed by several people, most of it from
Colin Cross and Erik Gilling.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Move harmony over to use the new gpio config table instead of having
separate settings in various parts of the code.
(The tegra sdhci driver should have the tegra_gpio_* ops removed, but
that will be done separately from this change.)
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
To give one place to setup the pins that are used as GPIOs instead
of as their pinmuxed functions. Specifying enabled as false explicitly
disables the gpio mode of that pin (if left on by firmware).
This should remove the need for calling these from specific drivers and
thus reduce tegra-specific code from them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
As planned by Arnd Bergmann, this moves the following drivers to the
drivers/staging/tty/ directory where they will be removed after 2.6.41
if no one steps up to claim them.
epca
epca
ip2
istallion
riscom8
serial167
specialix
stallion
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan missed the ia64 simulator serial driver (because it was hidden
in arch/... rather than located under drivers/... where one might
expect to find a driver). Drop the "file *" argument from rs_ioctl()
in arch/ia64/hp/sim/simserial.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option isn't terribly useful on other ARM platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Enable the cpu, emc (memory controller) and csite (debug and
trace controller) clocks during init to prevent them from
being disabled by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Enable the timer and rtc clocks to prevent them being
turned off by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Move tegra_common_init to tegra_init_early, and set it
as the init_early entry in the machine struct.
Initializes the clocks earlier so that timers can enable
their clocks.
Also reorders the members in the Harmony and Trimslice
boards' machine structs to match the order they are
called in.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Peripheral clocks that have no clock enable bit in the
enable registers have their clk_num set to 0. Bit 0
in the clock enable registers is the CPU clock.
Prevent disables on these peripheral clocks from
accidentally disabling the CPU clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Call the clock's round_rate op, if it exists, before calling
the set_rate op. This will help later when dvfs is added,
dvfs needs to know what the final rate will be before the
frequency changes.
Also requires fixes to the round rate functions to ensure
calling round rate and then set rate will not cause the
frequency to be rounded down twice. When picking clock
divider values, the clock framework picks the closest
frequency that is lower than the requested frequency. If
the new frequency calculated from the divider value is
rounded down, and then passed to set_rate, it will get
rounded down again, possibly resulting in a frequency two
steps lower than the original requested frequency.
Fix the problem by rounding up when calculating the frequency
coming out of a clock divider, so if that frequency is
requested again, the same divider value will be picked.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Some peripheral clocks share enable bits. Refcount the enables so
that calling clk_disable on one clock will not turn off another
clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Since the timer1 is now started before the hwmod_init, we cannot
reset it and idle it anymore.
Add the appropriate flags to prevent the hwmod framework to do that.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the hypervisor argument of dom0_mem=X we iterate over the physical
(only for the initial domain) E820 and subtract the the size from each
E820_RAM region the delta so that the cumulative size of all E820_RAM regions
is equal to 'X'. This sometimes ends up with E820_RAM regions with zero size
(which are removed by e820_sanitize) and E820_RAM that are smaller
than physically.
Later on the PCI API looks at the E820 and attempts to set up an
resource region for the "PCI mem". The E820 (assume dom0_mem=1GB is
set) compared to the physical looks as so:
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 0000000000097c00 (usable)
[ 0.000000] Xen: 0000000000097c00 - 0000000000100000 (reserved)
-[ 0.000000] Xen: 0000000000100000 - 00000000defafe00 (usable)
+[ 0.000000] Xen: 0000000000100000 - 0000000040000000 (usable)
[ 0.000000] Xen: 00000000defafe00 - 00000000defb1ea0 (ACPI NVS)
[ 0.000000] Xen: 00000000defb1ea0 - 00000000e0000000 (reserved)
[ 0.000000] Xen: 00000000f4000000 - 00000000f8000000 (reserved)
..
And we get
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:9efafe00)
while it should have started at e0000000 (a nice big gap up to
f4000000 exists). The "Allocating PCI" is part of the resource API.
The users that end up using those PCI I/O regions usually supply their
own BARs when calling the resource API (request_resource, or allocate_resource),
but there are exceptions which provide an empty 'struct resource' and
expect the API to provide the 'struct resource' to be populated with valid values.
The one that triggered this bug was the intel AGP driver that requested
a region for the flush page (intel_i9xx_setup_flush).
Before this patch, when running under Xen hypervisor, the 'struct resource'
returned could have (depending on the dom0_mem size) physical ranges of a 'System RAM'
instead of 'I/O' regions. This ended up with the Hypervisor failing a request
to populate PTE's with those PFNs as the domain did not have access to those
'System RAM' regions (rightly so).
After this patch, the left-over E820_RAM region from the truncation, will be
labeled as E820_UNUSABLE. The E820 will look as so:
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] Xen: 0000000000000000 - 0000000000097c00 (usable)
[ 0.000000] Xen: 0000000000097c00 - 0000000000100000 (reserved)
-[ 0.000000] Xen: 0000000000100000 - 00000000defafe00 (usable)
+[ 0.000000] Xen: 0000000000100000 - 0000000040000000 (usable)
+[ 0.000000] Xen: 0000000040000000 - 00000000defafe00 (unusable)
[ 0.000000] Xen: 00000000defafe00 - 00000000defb1ea0 (ACPI NVS)
[ 0.000000] Xen: 00000000defb1ea0 - 00000000e0000000 (reserved)
[ 0.000000] Xen: 00000000f4000000 - 00000000f8000000 (reserved)
For more information:
http://mid.gmane.org/1A42CE6F5F474C41B63392A5F80372B2335E978C@shsmsx501.ccr.corp.intel.com
BugLink: http://bugzilla.xensource.com/bugzilla/show_bug.cgi?id=1726
Signed-off-by: Fengzhe Zhang <fengzhe.zhang@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Allow the generic sleep code to be used with SMP CPU idle by storing
N CPU stack pointers rather than just one. Tested on Assabet and
Tegra 2.
Tested-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert sa11x0 to use the generic CPU suspend/resume support, rather
than implementing its own version. Tested on Assabet.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds core support for saving and restoring CPU coprocessor
registers for suspend/resume support. This contains support for suspend
with ARM920, ARM926, SA11x0, PXA25x, PXA27x, PXA3xx, V6 and V7 CPUs.
Tested on Assabet and Tegra 2.
Tested-by: Colin Cross <ccross@android.com>
Tested-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP4 supports up to 5 MMC controllers, but only 3 of these were
initialized. MMC5 is used by wl12xx chip. So initialize MMC4 and MMC5.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add MMC5 support on PANDA, which has the wl1271 device hardwired to.
The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.
Based on the patch for mmc3/wl1271 device support for zoom by Ohad
Ben-Cohen <ohad@wizery.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.
Based on the patch for zoom by Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE.
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc5 (fifth mmc controller) on the PANDA.
Based on the wlan board muxing for zoom3 by Ohad Ben-Cohen
<ohadb@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixed regulators in twl6030 do not have set_voltage hook.
Regulator core returns -22 if set_voltage is NULL and apply_uV is set
while applying the constraint to set voltage resulting in failure during probe
of these regulators.
Do not set apply_uV for fixed regulators which don't have set_voltage.
machine_constraints_voltage: VANA: failed to apply 2100000uV constraint
twl_reg twl_reg.43: can't register VANA, -22
twl_reg: probe of twl_reg.43 failed with error -22
machine_constraints_voltage: VCXIO: failed to apply 1800000uV constraint
twl_reg twl_reg.44: can't register VCXIO, -22
twl_reg: probe of twl_reg.44 failed with error -22
machine_constraints_voltage: VDAC: failed to apply 1800000uV constraint
twl_reg twl_reg.45: can't register VDAC, -22
twl_reg: probe of twl_reg.45 failed with error -22
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clean the regulator supply mapping data in the 3430sdp
board file (which is spread all over) by moving all
of them together.
Also use the REGULATOR_SUPPLY macro and remove instances
of mapping dev pointers at run time.
Additonally define all regulator_consumer_supply as
array's and use ARRAY_SIZE macro to define
num_consumer_supplies.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the dr_intercept function a new cpu-feature called
decode-assists is implemented and used when available. This
code-path does not advance the guest-rip causing the guest
to dead-loop over mov-dr instructions. This is fixed by this
patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Alloc code is much bigger the distance setting. Separate it out into
numa_alloc_distance() for readability.
-v2: Let alloc_numa_distance to return -ENOMEM on failing path,
requested by tj.
-tj: Description update. Minor tweaks including function name,
location and return value check.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Create numa_emulation.c and move all NUMA emulation code there. The
definitions of struct numa_memblk and numa_meminfo are moved to
numa_64.h. Also, numa_remove_memblk_from(), numa_cleanup_meminfo(),
numa_reset_distance() along with numa_emulation() are made global.
- v2: Internal declarations moved to numa_internal.h as suggested by
Yinghai.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Update numa_emulation() such that, it
- takes @numa_meminfo and @numa_dist_cnt instead of directly
referencing the global variables.
- copies the distance table by iterating each distance with
node_distance() instead of memcpy'ing the distance table.
- tests emu_cmdline to determine whether emulation is requested and
fills emu_nid_to_phys[] with identity mapping if emulation is not
used. This allows the caller to call numa_emulation()
unconditionally and makes return value unncessary.
- defines dummy version if CONFIG_NUMA_EMU is disabled.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
This patch changes the Kconfig and Makefile for the new ARCH_EXYNOS4.
It also updates arch/arm/Kconfig, Makeifile and arch/arm/mm/Kconfig
to include support for the new ARCH_EXYNOS4.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves board support files, SMDKC210, SMKDV310
and UNIVERSAL_C210 into arch/arm/mach-exynos4/ according
to the change of ARCH name, EXYNOS4.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates device support of EXYNOS4 according to the change of
ARCH name, EXYNOS4.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds EXYNOS4 CPU support files in mach-exynos4,
and basically they are moved from mach-s5pv310 so that it
can support Samsung's new CPU name, EXYNOS4.
The EXYNOS4 ingegrates a ARM Cortex A9 multi-core.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Increase virtual size of the frambuffer window 0
for display panning support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add I2C0 bus platform device for camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6745/1: kprobes insn decoding fix
ARM: tlb: move noMMU tlb_flush() to asm/tlb.h
ARM: tlb: delay page freeing for SMP and ARMv7 CPUs
ARM: Keep exit text/data around for SMP_ON_UP
ARM: Ensure predictable endian state on signal handler entry
ARM: 6740/1: Place correctly notes section in the linker script
ARM: 6700/1: SPEAr: Correct SOC config base address for spear320
ARM: 6722/1: SPEAr: sp810: switch to slow mode before reset
ARM: 6712/1: SPEAr: replace readl(), writel() with relaxed versions in uncompress.h
ARM: 6720/1: SPEAr: Append UL to VMALLOC_END
ARM: 6676/1: Correct the cpu_architecture() function for ARMv7
ARM: 6739/1: update .gitignore for boot/compressed
ARM: 6743/1: errata: interrupted ICALLUIS may prevent completion of broadcasted operation
ARM: 6742/1: pmu: avoid setting IRQ affinity on UP systems
ARM: 6741/1: errata: pl310 cache sync operation may be faulty
- Add a rev attribute to identify various McSPI IP version.
- Add a dev_attr structure to provide the number of chipselect
supported by the instance.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Marcin Slusarz says:
> In arch/arm/kernel/kprobes-decode.c there's a function
> arm_kprobe_decode_insn which does:
>
> } else if ((insn & 0x0e000000) == 0x0c400000) {
> ...
>
> This is always false, so code below is dead.
> I found this bug by coccinelle (http://coccinelle.lip6.fr/).
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to noMMU to put tlb_flush() in asm/tlbflush.h - it's
part of the tlb shootdown interface. Move it to asm/tlb.h instead, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to delay freeing any mapped page on SMP and ARMv7 systems to
ensure that the data is not accessed by other CPUs, or is used for
speculative prefetch with ARMv7. This includes not only mapped pages
but also pages used for the page tables themselves.
This avoids races with the MMU/other CPUs accessing pages after they've
been freed but before we've invalidated the TLB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Cc: <stable@kernel.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Cc: <stable@kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 18991197b4 added --build-id
linker option when toolchain supports it. ARM one does, but for some
reason places the section at 0 when linker script doesn't mention it
explicitly.
The 1e621a8e37 worked around the problem
removing this section from binary image with explicit objcopy options,
but it still exists in vmlinux, confusing tools like debuggers and perf.
This problem was discussed here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.htmlhttp://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.html
but the proposed changes to the linker script were substantial.
This patch simply places NOTES (36 bytes long, at least when compiled
with CodeSourcery toolchain) between data and bss, which seem to be
the right place (and suggested by the sample linker script in
include/asm-generic/vmlinux.lds.h).
It is enough to place it correctly in vmlinux (so debuggers are happy):
Section Headers:
[11] .data PROGBITS c07ce000 7ce000 020fc0 00 WA 0 0 32
[12] .notes NOTE c07eefc0 7eefc0 000024 00 AX 0 0 4
[13] .bss NOBITS c07ef000 7eefe4 01e628 00 WA 0 0 32
Program Headers:
LOAD 0x008000 0xc0008000 0xc0008000 0x7e6fe4 0x805628 RWE 0x8000
NOTE 0x7eefc0 0xc07eefc0 0xc07eefc0 0x00024 0x00024 R E 0x4
Section to Segment mapping:
Segment Sections...
00 <...> .data .notes .bss
01 .notes
and to get it exposed as /sys/kernel/notes used by perf tools.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPEAR320_SOC_CONFIG_BASE was wrong, causing the wrong registers to be
accessed.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In sysctl_soft_reset(), switch to slow mode before resetting the system
via the system controller. This is required.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
readl() and writel() calls the outer cache maintainance operations
which are not available during Linux uncompression. This patch replaces
readl() and writel() with readl_relaxed() and writel_relaxed() to avoid
the link time errors.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes following warning:
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
by appending UL to VMALLOC_END's Number.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add pud_offset() et.al. between the pgd and pmd code in preparation of
using pgtable-nopud.h rather than 4level-fixup.h.
This incorporates a fix from Jamie Iles <jamie@jamieiles.com> for
uaccess_with_memcpy.c.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The unsigned long datatype is not sufficient for mapping physical addresses
>= 4GB.
This patch ensures that the phys_addr_t datatype is used to represent
the start address of a membank, which may reside above the 4GB boundary.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By the time setup_node_bootmem() is called, all the memblocks are
already registered. As node_data is allocated from these memblocks,
calling it more than once doesn't make any difference. Drop the loop.
tj: Dropped comment referencing to the old behavior as suggested by
David and rephrased the description.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Different board have different requirements/setups so let's be more
flexible.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change prefixes from qt602240 to mxt to reflect that the driver supports
whole line of mXT touchscreens.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since the driver will be supporting whole range of Atmels mXT touchscreen
controllers we better rename it to atmel_mxt_ts.
Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Correct max rates for pclk and sclk (Originally fixed by
Dima Zavin <dima@android.com>)
Correct max rate for plla (Originally fixed by
Stephen Warren <swarren@nvidia.com>)
Remove unnecessary no-op set_rate on audio clocks
Add clock lookup entries for grhost, bsea, and vde clocks
Update clock clookup entries for vcp, bsea, and vde clocks
Add shared clock entries for sclk and emc
Add a virtual cop clock to provide a reset op (Originally fixed by
Dima Zavin <dima@android.com>)
Pass set_rate on super clocks through to parent
Fix pllx frequency table entry for 608 MHz
Remove incorrect plla frequency table entries
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLLP registers are now being restored by the low-level resume code,
and the CPU may be running off PLLP, so don't touch them during clock
resume.
Save plld, plls, pllu, and audio clock during suspend (originally
fixed by Mayuresh Kulkarni <mkulkarni@nvidia.com>)
The lock time for plld is 1000 us, so increase the delay after
setting the PLLs.
Add a BUG_ON to ensure the size of the suspend context area is
correct.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The SDMMC controllers have extra bits in the clock source
register that adjust the delay between the clock and data
to compenstate for delays on the PCB. The values need to
be set from the clock code so the clock can be locked
during the read-modify-write on the clock source register.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Adjusts the minimum memory frequency when the cpu frequency
changes. The values are currently hardcoded to a reasonable
default. If memory frequency scaling is not enabled this
patch will have no effect.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add clock ops on the emc peripheral clock that call into the
emc driver to update the memory controller registers for the
new frequency. Tegra has an interlock between the clock
controller and the memory controller that prevents the new
register values from taking effect until the clock frequency
update occurs.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The frequency memory bus on Tegra can be adjusted without
disabling accesses to memory by updating the memory
configuration registers from a per-board table, and then
changing the clock frequency. The clock controller and
memory controller have an interlock that prevents the
new memory registers from taking effect until the
clock frequency change.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Remove unnecessary uses of #ifdef CONFIG_DEBUG_FS
Convert bool assignments from 1 to true
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Some clocks may have multiple downstream users that need to request a
higher clock rate. Shared bus clocks provide a unique shared_bus_user
clock to each user. The frequency of the bus is set to the highest
enabled shared_bus_user clock, with a minimum value set by the
shared bus. Drivers can use clk_enable and clk_disable to enable
or disable their requirement, and clk_set_rate to set the minimum rate.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
During cpu frequency changes, take an extra reference to pllx so
that it doesn't turn off and on while the cpu is temporarily on
pllp. If the cpu is moved to pllp permanently, pllx will be
turned off.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Give each clock its own lock, and remove all lock traversals from
parent to child clocks to prevent AB-BA deadlocks.
This brings the locking in line with the common struct clk
patches and should make conversion simple.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Creates a union of a struct for each type of clock to reduce memory
usage and clarify which members are used by all clocks and which are
used by a single type.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Make the static clocks look more like the array of clocks
so they can all be initalized with the same helper function.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The existing version did not extend well to core dvfs, drop it
for now until the new clk api with clk_prepare and clk_unprepare
is ready and non-atomic clocks are possible.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
VersaLogic Menlow based boards hang on reboot unless reboot=bios
is used. Add quirk to reboot through the BIOS.
Tested on at least four boards.
Signed-off-by: Kushal Koolwal <kushalkoolwal@gmail.com>
LKML-Reference: <1298152563-21594-1-git-send-email-kushalkoolwal@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The PLL lock bits are not reliable, use per-PLL timeouts instead.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Drop the unnecessary pr_debug calls to avoid having to maintain them.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
When updating the CPU PLL frequency, keeping the PLL enabled avoids
ramping the PLL all the way down and back up again. Remove the BUG_ON
in tegra2_pll_clk_set_rate to allow the rate to change while the PLL
is enabled.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add a new 'reset' clk op. This can be provided for any clock,
not just peripherals.
Signed-off-by: Dima Zavin <dima@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
This seems to be a regression in 2.6.37.
We cannot use writel() here since the resulting wmb() calls l2x0_cache_sync()
which uses a spinlock and L1 cache may be off at this point.
http://lists.infradead.org/pipermail/linux-arm-kernel/2011-February/041909.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Colin Cross <ccross@android.com>
install_equiv_cpu_table() returns type int. It uses negative
error codes so using an unsigned type breaks the error handling.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: open list:AMD MICROCODE UPD... <amd64-microcode@amd64.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20110218091716.GA4384@bicker>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Those are unused since at least the beginning of git history.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1298044056-31104-1-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If a request already in the queue is passed to tegra_dma_enqueue_req,
tegra_dma_req.node->{next,prev} will end up pointing to itself instead
of at tegra_dma_channel.list, which is the way a the end-of-list
should be set up. When the DMA request completes and is list_del'd,
the list head will still point at it, yet the node's next/prev will
contain the list poison values. When the next DMA request completes,
a kernel panic will occur when those poison values are dereferenced.
This makes the DMA driver more robust in the face of buggy clients.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The kernel doesn't officially need to interwork, but using BX
wherever appropriate will help educate people into good assembler
coding habits.
BX is appropriate here because this code is predicated on
__LINUX_ARM_ARCH__ >= 6
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If ID_MMFR0[3:0] >= 3, the architecture version is ARMv7. The code was
currently only testing for ID_MMFR0[3:0] == 3.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On versions of the Cortex-A9 prior to r3p0, an interrupted ICIALLUIS
operation may prevent the completion of a following broadcasted
operation if the second operation is received by a CPU before the
ICIALLUIS has completed, potentially leading to corrupted entries in
the cache or TLB.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
causing CP15 maintenance operations to be uninterruptible.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we can execute a CONFIG_SMP kernel on a uniprocessor system,
extra care has to be taken in the PMU IRQ affinity setting code to
ensure that we don't always fail to initialise.
This patch changes the CPU PMU initialisation code so that when we
only have a single IRQ, whose affinity can not be changed at the
controller, we report success (0) rather than -EINVAL.
Reported-by: Avik Sil <avik.sil@linaro.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The effect of cache sync operation is to drain the store buffer and
wait for all internal buffers to be empty. In normal conditions, store
buffer is able to merge the normal memory writes within its 32-byte
data buffers. Due to this erratum present in r3p0, the effect of cache
sync operation on the store buffer still remains when the operation
completes. This means that the store buffer is always asked to drain
and this prevents it from merging any further writes.
This can severely affect performance on the write traffic esp. on
Normal memory NC one.
The proposed workaround is to replace the normal offset of cache sync
operation(0x730) by another offset targeting an unmapped PL310
register 0x740.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Integrator/CP has the 24MHz counter which Versatile and later platforms
also have, which we use for sched_clock support. Allow this counter to
be used when building a kernel targetting Integrator/CP alone.
Integrator/AP does not have this counter, so we must exclude support
for the Integrator family when this is enabled.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Realview and Versatile Express share the same SMP bringup code, so
consolidate the two implementations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Realview and Versatile Express local timer support is identical, so
consolidate the implementations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the FPGA IRQ handling code. Integrator/AP and Versatile
have one FPGA-based IRQ handler each. Integrator/CP has three.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move leds and sched_clock build conditionals out of the Makefile into
the Kconfig file. Move selection of HAVE_SCHED_CLOCK into the
platform Kconfig rather than duplicating it three times in the main
architecture Kconfig.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AMBA DMA macro definitions are not used, and the AMBA Primecell DMA
support makes no use of them either, so they can be removed.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AMBA DMA macro definitions are not used, and the AMBA Primecell DMA
support makes no use of them either, so they can be removed.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialize the clock tree and our sched_clock() early.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialize the clock tree and our sched_clock() early.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialize the clock tree and our sched_clock() early.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches Versatile Express to use the conslidated CLCD panel
support, including the display capabilities. As Versatile Express uses
a PL111, it can support the full range of pixel formats - 444, 5551,
565 in both RGB and BGR mode.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches Realview platforms to use the consolidated CLCD panel
support, including the display capabilities. As Realview uses a PL111,
it can support the full range of pixel formats - 444, 5551, 565 in both
RGB and BGR mode.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches Versatile platforms to use the consolidated CLCD panel
support, including the display capabilities. Versatile can support
RGB5551, BGR5551, RGB565 and BGR565 modes.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches integrator platforms to use the consolidated CLCD
panel support, including the display capabilities. These capabilities
prevent the unsupported BGR565 mode being selected, while still
allowing RGB5551, BGR5551 and RGB565 modes.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This consolidates the CLCD panel definitions and memory allocation into
one location.
Rename the Sanyo 2.5in and Epson 2.2in displays after their respective
part numbers. Rather than using a general "Sanyo 2.5in" and "Epson
2.2in" description of the display panel, use the manufacturers part
number to be more specific. This helps people identify what the timings
actually refer to, which are panel specific.
While here, add CLCD capability information to each panel definition,
which has no effect until we add the board-level capabilities.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the CLCD is in anything but RGB888 mode, its outputs are configured
for RGB5551 output. Integrator/CP supports RGB565 via an external
multiplexer, which we configure for RGB5551 or RGB565 based only on the
bits per pixel. So when userspace asks for the RGB555 layout, the mux
remains in RGB565 mode, and we produce incorrect colours. Fix this.
Note that Integrator doesn't support BGR565 mode, but does support
BGR5551.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RGB565 with blue in the LSB wasn't supported. Add support for this
layout.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Being able to compile a major reference platform is helpful for
me when developing on other archs using the same e.g. PrimeCells.
I bet this is useful to others as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Config and activate all the devices we've merged for Ux500
in 2.6.38-rc1. This is needed for the default config to compile
properly.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the static inline functions for gpio_to_irq/irq_to_gpio so that
they can be used in static initialisers.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removed unused variable left over from development.
Reported-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <AANLkTik6UJ680mWJcu_W+jerLcqPjwjvaXyxB1jAMaG0@mail.gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
The initial version of this patch had %eax being a segment and %ecx
being the mode. I had changed the interfaces, but not the actual
implementation!
Reported-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <AANLkTikxqk=HEw9R-Du=v-1ti1HDGAY9vaNUep2XARaz@mail.gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
APB timer current count was unreliable in the earlier silicon, which
could result in time going backwards. This problem has been fixed in
the current silicon stepping. This patch removes the workaround which
was used to check and prevent timer rolling back when APB timer is
used as clocksource device.
The workaround code was also flawed by potential race condition
around the cached read value last_read. Though a fix can be done
by assigning last_read to a local variable at the beginning of
apbt_read_clocksource(), but this is not necessary anymore.
[ tglx: A sane timer on an Intel chip - I can't believe it ]
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Cox <alan@linux.intel.com>
LKML-Reference: <1298065374-25532-1-git-send-email-jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This code path is only run when an MSI/MSI-X PCI device is passed
in to PV DomU.
In 2.6.37 time-frame we over-wrote the default cleanup handler for
MSI/MSI-X irq->desc to be "xen_teardown_msi_irqs". That function
calls the the xen-pcifront driver which can tell the backend to
cleanup/take back the MSI/MSI-X device.
However, we forgot to continue the process of free-ing the MSI/MSI-X
device resources (irq->desc) in the PV domU side. Which is what
the default cleanup handler: default_teardown_msi_irqs did.
Hence we would leak IRQ descriptors.
Without this patch, doing "rmmod igbvf;modprobe igbvf" multiple
times ends with abandoned IRQ descriptors:
28: 5 xen-pirq-pcifront-msi-x
29: 8 xen-pirq-pcifront-msi-x
...
130: 10 xen-pirq-pcifront-msi-x
with the end result of running out of IRQ descriptors.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cleanup code. Cosmetic change to make the code look easier
to read.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|arch/x86/pci/ce4100.c: In function `ce4100_conf_read':
|arch/x86/pci/ce4100.c:257:9: warning: unused variable `retval'
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: dirk.brandewie@gmail.com
LKML-Reference: <1292600033-12271-16-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
xen_allocate_pirq -> xen_map_pirq_gsi -> PHYSDEVOP_alloc_irq_vector IFF
xen_initial_domain() in addition to the kernel side book-keeping side of
things (set chip and handler, update irq_info etc) whereas
xen_allocate_pirq_msi just does the kernel book keeping.
Also xen_allocate_pirq allocates an IRQ in the 1-1 GSI space whereas
xen_allocate_pirq_msi allocates a dynamic one in the >GSI IRQ space.
All of this is uneccessary as this code path is only executed
when we run as a domU PV guest with an MSI/MSI-X PCI card passed in.
Hence we can jump straight to allocating an dynamic IRQ (and
binding it to the proper PIRQ) and skip the rest.
In short: this change is a cosmetic one.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Introduced the suspend/resume function for the OMAP4430 internal PHY.
This will be used by the twl6030-usb transceiver driver.
Moved the clock enable/disable function calls and power on/off of the PHY
code from power on/off functions to suspend/resume function.
Pass the suspend function through board data for OMAP4430sdp and OMAP4panda.
This will be used by the twl6030-usb transceiver driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most fix is for uart txd/cts. They don't need to select input.
And fix some other pads with wrong select input.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch declares regulators for the efikamx. Use it also to power off the
efikamx.
Unfortunately, on the efikamx to2 boards, this doesn't work but they allow to
power off by setting GPIO 4 13 to high level instead of powering off through
the mc13892.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Genesi EFIKA MX and EFIKA Smartbook are sharing a lot of things
so it makes sense to create a common file for both devices and a specific
file for each. No functionnal change except dropping uart 1 & 2.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit 1130e5b3ff regulators are exported to debugfs. The names
of the regulators that contains slash ('/') causes an ops during kernel
boot. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Max8998 PMIC driver's platform data has been changed once again in
commit 735a3d9efd. This patch fixes build break caused by that commit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c24xx_ts_set_platdata is annotated __init and not used by any module,
thus don't export it.
This patch fixes below warning:
WARNING: arch/arm/plat-samsung/built-in.o(__ksymtab+0x90): Section mismatch
in reference from the variable __ksymtab_s3c24xx_ts_set_platdata to the
function .init.text:s3c24xx_ts_set_platdata()
The symbol s3c24xx_ts_set_platdata is exported and annotated __init
Fix this by removing the __init annotation of s3c24xx_ts_set_platdata
or drop the export.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Not only when an IRQ's affinity equals cpu_online_mask is there
no need to actually try to adjust the affinity, but also when
it's a subset thereof. This particularly avoids adjustment
attempts during system shutdown to any IRQs bound to CPU#0.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Gary Hade <garyhade@us.ibm.com>
LKML-Reference: <4D5D52C2020000780003272C@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With no caller left, the function and the DIE_NMIWATCHDOG
enumerator can both go away.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Don Zickus <dzickus@redhat.com>
LKML-Reference: <4D5D521C0200007800032702@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Printing a single character alone when there's an immediately
following printk() is pretty pointless (and wasteful).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4D5D535A0200007800032730@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
show_regs() already prints two(!) stack traces, no need for a third one.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4D5D512902000078000326EE@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the real-mode reboot code out to an assembly file (reboot_32.S)
which is allocated using the common lowmem trampoline allocator.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Make the GDT_ENTRY() macro in <asm/segment.h> safe for use in
assembly code by guarding the ULL suffixes with _AC() macros.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Use the unified trampoline allocation setup to allocate and install
the ACPI wakeup code in low memory.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Common infrastructure for low memory trampolines. This code installs
the trampolines permanently in low memory very early. It also permits
multiple pieces of code to be used for this purpose.
This code also introduces a standard infrastructure for computing
symbol addresses in the trampoline code.
The only change to the actual SMP trampolines themselves is that the
64-bit trampoline has been made reusable -- the previous version would
overwrite the code with a status variable; this moves the status
variable to a separate location.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Allow OMAP4 ES2.1 and ES2.2 revisions to be recognized in the
omap4_check_revision() function.
Mainly, ES2.1 has fixes that allow LPDDR to be used at 100% OPP (400MHz).
ES2.2 additionally has a couple of power management fixes (to reduce
leakage), an I2C1 SDA line state fix, and a floating point write
corruption fix (cortex erratum).
Even though the current mainline support doesn't need to distinguish
between ES2.X versions, it's still useful to know the correct silicon
rev when issues are reported. Moreover, these id checks can be used by
power management code that selects suitable OPPs considering the
memory speed limitation on ES2.0.
For details about the silicon errata on OMAP4430, refer
http://focus.ti.com/pdfs/wtbu/SWPZ009A_OMAP4430_Errata_Public_vA.pdf
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change all occurences of printf() to pr_err().
Includes minor formatting changes as result of
this change.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes typos that were remaining after
the file and functions were renamed.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Declaration of exported function 'iopgtable_lookup_entry' is missing from
header file. Currently we have a sparse warning as it's not being used
externally. Adding its declaration to avoid such warning and allow its usage
in future.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OneNAND version ID may not give the highest frequency
supported and some OneNAND's have setup times that are
clock dependent. Let the board provide that information.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OneNAND frequency is determined when calculating
GPMC timings. Return that value instead of determining it
again in the OMAP OneNAND driver.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
104MHz needs a latency of 8 clock cycles and the VHF
flag must be set. Also t_rdyo is specified as
"not applicable" so pick a lower value, and force at
least 1 clk between AVD High to OE Low.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the OMAP3430SDP board, the ads7846 touchscreen controller
is powered by VAUX3 regulator (supplying 2.8v).
Fix this mapping in the board file, and hence prevent
the ads7846 driver init to fail with the below error..
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch overrides nand ecc layout and bad block descriptor (for 8-bit
device) to support hw ecc in romcode layout. So as to have in sync with ecc
layout throughout; i.e. x-loader, u-boot and kernel.
This enables to flash x-loader, u-boot, kernel, FS images from kernel itself
and compatiable with other tools.
This patch does not enables this feature by default and need to pass from
board file to enable for any board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes it possible to select sw or hw (different layout options)
ecc scheme supported by omap nand driver.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure the FIFO THREASHOLD value different for read and write to keep busy
both filling and to drain out of FIFO at reading and writing.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support the irq mode in GPMC.
gpmc_init() function move after omap_init_irq() as it has dependecy on irq.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
nand transfer type (sDMA, Polled, prefetch) can be select from board file,
enabling all transfer type in driver, by default.
this helps in multi-omap build and to select different transfer type for
different board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
zoom3 and 3630-sdp having the x16 nand device.
This patch configure gpmc as x16 and select the currect function in driver
for polled mode (without prefetch enable) transfer.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The unsigned long datatype is not sufficient for mapping physical addresses
>= 4GB.
This patch ensures that the address conversion code in asm/memory.h casts
to the correct type when handling physical addresses. The internal v2p
macros only deal with lowmem addresses, so these do not need to be modified.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If ATAGs or DTB pointer is not within first 1MB of RAM, then the boot params
will not be mapped early enough, so map the 1MB region that r2 points to. Only
map the first 1MB when r2 is 0.
Some assembly improvements from Nicolas Pitre.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MSM's memory is aligned to 2MB, which is more than we can do with our
existing method as we're limited to the upper 8 bits. Extend this by
using two instructions to 16 bits, automatically selected when MSM is
enabled.
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This idea came from Nicolas, Eric Miao produced an initial version,
which was then rewritten into this.
Patch the physical to virtual translations at runtime. As we modify
the code, this makes it incompatible with XIP kernels, but allows us
to achieve this with minimal loss of performance.
As many translations are of the form:
physical = virtual + (PHYS_OFFSET - PAGE_OFFSET)
virtual = physical - (PHYS_OFFSET - PAGE_OFFSET)
we generate an 'add' instruction for __virt_to_phys(), and a 'sub'
instruction for __phys_to_virt(). We calculate at run time (PHYS_OFFSET
- PAGE_OFFSET) by comparing the address prior to MMU initialization with
where it should be once the MMU has been initialized, and place this
constant into the above add/sub instructions.
Once we have (PHYS_OFFSET - PAGE_OFFSET), we can calculate the real
PHYS_OFFSET as PAGE_OFFSET is a build-time constant, and save this for
the C-mode PHYS_OFFSET variable definition to use.
At present, we are unable to support Realview with Sparsemem enabled
as this uses a complex mapping function, and MSM as this requires a
constant which will not fit in our math instruction.
Add a module version magic string for this feature to prevent
incompatible modules being loaded.
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are needed for CONFIG_ARM_PATCH_PHYS_VIRT to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
head.S makes use of PHYS_OFFSET. When it becomes a variable, the
assembler won't understand this. Compute PHYS_OFFSET by the following
method. This code is linked at its virtual address, but run at before
the MMU is enabled, so at his physical address.
1: .long .
.long PAGE_OFFSET
adr r0, 1b @ r0 = physical ','
ldmia r0, {r1, r2} @ r1 = virtual '.', r2 = PAGE_OFFSET
sub r1, r0, r1 @ r1 = physical-virtual
add r2, r2, r1 @ r2 = PAGE_OFFSET + physical-virtual
@ := PHYS_OFFSET.
Switch XIP users of PHYS_OFFSET to use PLAT_PHYS_OFFSET - we can't
use this method for XIP kernels as the code doesn't execute in RAM.
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As PHYS_OFFSET will be becoming a variable, we can't have it used in
initializers nor assembly code. Replace those in generic code with
a run-time initialization. Replace those in platform code using the
individual platform specific PLAT_PHYS_OFFSET.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set OMAP_PIN_OFF_WAKEUPENABLE to enable the wake-up
functionality from touchscreen controller.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If you choose default output to DVI, the LCD backlight used to
stay on, since panel->disable function never gets called.
So, during init put backlight GPIO to off state and the driver
code will decide which output to enable.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is useful for system management software so that it can kick
off things like gettys and everything that's started from a tty,
before we reuse it from/for something else or shut it down.
Without this ioctl it would have to temporarily become the owner of
the tty, then call vhangup() and then give it up again.
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To support higher resolution (e.g 720P@60), on OMAP36x (AM/DM37x)
DSS data bus has been muxed with sys_boot pins.
DSS[18-23] => DSS[0-5]
sys_boot[0,1 3-5] => DSS[18-23]
EVM revision >=RevB adopt this mux changes, which is going to ship outside.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since TWL GPIO's can go into sleep, and using normal
gpio_get/set_value() API will lead to kernel dump (WARN_ON()).
So replacing standard gpio_get/set_value() to
gpio_get/set_value_cansleep().
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Charulatha V <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With addition of hwmod support to gpio, the ethernet controller
goes undetected for OMAP35xEVM. So explicitly assert the reset signal to
ethernet controller smsc911x -
- GPIO7 (>=RevG version of EVM's)
- GPIO64 (<=RevD version of EVM's)
Tested this patch on RevG version of EVM with ES3.1 Si.
This patch is based on intial version from Charulatha V, reference
to original discussion -
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg35784.html
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just as we had to disable auto-demotion for NHM/WSM,
we need to do the same for Atom (Lincroft version).
In particular, auto-demotion will prevent Lincroft
from entering the S0i3 idle power saving state.
https://bugzilla.kernel.org/show_bug.cgi?id=25252
Signed-off-by: Len Brown <len.brown@intel.com>
Hardware C-state auto-demotion is a mechanism where the HW overrides
the OS C-state request, instead demoting to a shallower state,
which is less expensive, but saves less power.
Modern Linux should generally get exactly the states it requests.
In particular, when a CPU is taken off-line, it must not be demoted, else
it can prevent the entire package from reaching deep C-states.
https://bugzilla.kernel.org/show_bug.cgi?id=25252
Signed-off-by: Len Brown <len.brown@intel.com>
Adds platform initialization for working with the WLAN module attached to the evaluation module.
The patch includes MMC2 initialization, SDIO and control pins muxing and platform device registration
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-Add the platform changes for the keypad driver
-Register keyboard device with hwmod framework.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap44xx_sram_init() implements functionality to push some
code on SRAM whenever the code can't be executed from external
memory. The low power and DVFS code can be executed from
external DDR itself thanks to OMAP4 memory controller hardware
support. So on OMAP4, sram_push kind of functionality isn't needed.
Hence remove the FIXME warning added for implementing sram push
feature on OMAP4.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap2plus_defconfig picks default NR_CPU value as 4 which isn't
correct for OMAP4430. Available CPUs are ony 2, so fix the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleans up all base address definitions for omap_mcspi
and adapts the device registration and driver to hwmod framework.
Changes involves:
1) Removing all base address macro defines.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute(number of chipselect).
3) Appending base address with pdata reg_offset for omap4 boards.
For omap4 all regs used in driver deviate with reg_offset_macros
defined with an value of 0x100. So pass this offset through pdata
and append the same to base address retrieved from hwmod data file
and we are not mapping *_HL_* regs which are not used in driver.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update omap3 hwmod data file with McSPI info.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the 2430 hwmod data file with McSPI info.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the omap2420 hwmod data with the McSPI info.
Add a device attribute structure which will be used
for passing number of chipselects from hwmod data.
Add revision macros to be passed from rev field from
hwmod.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build and register an hwspinlock platform device.
Although only OMAP4 supports the hardware spinlock module (for now),
it is still safe to run this initcall on all omaps, because hwmod lookup
will simply fail on hwspinlock-less platforms.
Signed-off-by: Simon Que <sque@ti.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 hwmod data structures are populated with base address, L3 and L4
interface clocks, IRQs and sysconfig register details.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and offmode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags,framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when idled.
Signed-off-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[b-cousson@ti.com: Fix position, opt_clk, and author]
Add more hwmod structures but keep them commented out for the moment
until the driver adaptation to hwmod / omap_device is done.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Add mcbsp data including a revision member in hwmod_class in
order to provide mcbsp revision information in different omap.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
[b-cousson@ti.com: Remove the mcbsp4 memory name, re-order
properly the structures]
Add HWMOD entries for the OMAP DMIC. The HWMOD entires define the system
resource requirements for the driver such as DMA addresses, channels,
and IRQ's. Placing this information in the HWMOD database allows for
more generic drivers to be written and having the specific implementation
details defined in HWMOD.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: David Lambert <dlambert@ti.com>
[b-cousson@ti.com: Change the wrong hwmod name,
add missing flag and re-order structures]
Mailbox hwmod data for omap4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[b-cousson@ti.com: Re-order the structures
and remove the irq line name]
Add dss, dispc, dsi1, dsi2, hdmi, rfbi and venc hwmods.
In OMAP4 there are severals IPs that can be reached by differents
interconnect paths depending of the access initiator (MPU vs. SDMA).
In the case of the DSS, both L3 direct path and L4 CFG path can be
used to access all the DSS IPs. The two ocp_ip already exists to support
the two address spaces.
+------------+-- L3_MAIN --+ MPU
IP | |
+-- L4_CFG --+
L3 main address range is specified first, since it is used by default.
dss is also considered as an IP as dispc, rfbi, and named as dss_core.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
[b-cousson@ti.com: Re-organize structures to match file
convention and remove irq entry from dss_hwmod]
Add the data for the 11 timers IPs.
OMAP4 contains two differents IP variants for the timers:
- 8 x regular timer (3, 4, 5, 6, 7, 8, 9 & 11)
- 3 x 1ms timer (1, 2 & 10)
The regular timers registers programming model was changed due to the
adaptation to the new IP interface. Unfortunately the 1ms version
still use the previous programming model. The driver will have
to take care of theses differences.
Please note that the capability and the partitioning is also
different depending of the instance.
- timer 1 is inside the wakeup domain
- timers 5, 6, 7 & 8 are inside in the ABE (audio backend)
- timers 2, 3, 4, 9, 10 & 11 are inside the PER power domain
The timer was previously named gptimerX or dmtimerX, it is
now simply named timerX.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
[b-cousson@ti.com: Fix alignement in class attribute,
re-order flags and update the changelog]
Using omap_device_build API instead of platform_device_register for
OMAP2430,OMAP3xxx, OMAP4430 and AM35x musb device registration.
The device specific resources defined in centralized
database will be used.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
do_file_page and do_no_page don't exist anymore, but some comments
still refers them. The patch fixes them by replacing them with
existing ones.
Signed-off-by: Ryota Ozaki <ozaki.ryota@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
AM35xx hwmod data structures are populated for USBOTG with base address,
L3 and L4 interface clocks and IRQ.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OMAP3 hwmod data structures are populated for USBOTG with base address,
L3 and L4 interface clocks, IRQs and sysconfig register details.
This is applicable for OMAP3430 amd OMAP3630.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and offmode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags, framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when idled.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OMAP2430 hwmod data structures are populated with base address, L3 and L4
interface clocks, IRQs and sysconfig register details.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and off-mode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags, framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when suspended.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the mux framework APIs to explicitly configure
the MUSB pads. The MUSB controller in OMAP4 can use
either the old ULPI interface, or the new internal PHY.
Configure the pads accordingly.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Moved all the board specific internal PHY functions out of usb_musb.c file
as this file is shared between the OMAP2+ and AM35xx platforms.
There exists a file which has the functions specific to internal PHY
used for OMAP4 platform. Moved all phy specific functions to this file
and passing these functions through board data in the board file.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dummy_numa_init() is used only during system boot. Put it in .init
like other NUMA init functions.
- tj: Description update.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Do not call __pa(numa_distance) if it was not allocated before.
Calling with invalid address triggers VIRTUAL_BUG_ON() in
__phys_addr() if CONFIG_DEBUG_VIRTUAL.
Also reported by Ingo.
http://thread.gmane.org/gmane.linux.kernel/1101306/focus=1101785
- v2: Change to check existing path as tj requested.
- tj: Description update.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ingo Molnar <mingo@elte.hu>
Use bitmap_set()/bitmap_clear() to fill/zero a region of a
bitmap instead of doing set_bit()/clear_bit() each bit.
This change has been tested with ioperm() and there's no
change in behavior.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
LKML-Reference: <1297867715-20394-1-git-send-email-akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
DB8500 has irqs from two cores ORed into one. Implement a
workaround to handle this by bouncing the interrupt by setting
the affinity to the other core when the interrupt appears to
be spurious on the current core.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow a platform-specific IRQ handler to be specified via platform data.
This will be used to implement the single-irq workaround for the DB8500.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
NET_SKB_PAD has been increased from 32 to 64 and later to
max(32, L1_CACHE_BYTES). This led to a 25% throughput decrease for
streaming workloads accompanied by a 37% CPU cost increase on s390.
Define a architecture specific NET_SKB_PAD with the old value of 32.
Signed-off-by: Horst Hartmann <horsth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use inline assemblies for atomic_read/set(). This way there shouldn't
be any questions or subtle volatile semantics left.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 'output' variable is passed from decompress_kernel to
check_ipl_parmblock before it is initialized. That disables the
safe guard against the overwrite of the ipl parameter block.
Fix this by passing the correct value to check_ipl_parmblock.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let's make atomic_read() and atomic_set() behave like on all/most other
architectures. Generated code is identical with gcc 4.5.2.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
i.MX23 Reference Manaul starts auart index from 1 than 0. Changing
the index to start from 0 requires corresponding changes on base
address, irq, and iomux definitions, and will probably confuse people
who reads codes and hardware documents together.
This patch introduced the field 'hwid' to distinguish the driver id
and controller id. These two ids are different on mx23 while
identical on mx28.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX23 Reference Manual names auart irq differently from i.MX28.
This patch is to align the naming with mx28, so that some device
registration codes can be shared.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add hwspinlock hwmod data for OMAP4 chip
Signed-off-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Paul Walmsley <paul@pwsan.com>
[b-cousson@ti.com: Move the data to keep the original
order and add missing SIDLE_SMART_WKUP flag]
For S5P platforms, the end address in memory resource information for UART
devices is one byte more than the intended value. Fix this by reducing the
end address by one byte.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix the following compile warning:
arch/arm/mach-omap2/clkt_clksel.c: In function '_get_div_and_fieldval':
arch/arm/mach-omap2/clkt_clksel.c💯35: warning: 'max_clkr' may be
used uninitialized in this function
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for low level debugging on TI816X boards. Currently the
support for UART3 console on TI816X EVM is added.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support and build configuration for TI816X EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files with support for
TI816X.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with TI816X support.
The approach taken in this patch is to add TI816X as part of OMAP3 variant where
the cpu class is considered as OMAP34XX and the type is TI816X. This means, both
cpu_is_omap34xx() and cpu_is_ti816x() checks return success on TI816X.
A kernel config option CONFIG_SOC_OMAPTI816X is added under OMAP3 to include
support for TI816X build.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NUMA emulation needs to update node distance information. It did it
by remapping apicid to PXM mapping, even when amdtopology is being
used. There is no reason to go through such convolution. The generic
code has all the information necessary to transform the distance table
to the emulated nid space.
Implement generic distance table transformation in numa_emulation()
and drop private implementations in srat_64 and amdtopology_64. This
makes find_node_by_addr() and fake_physnodes() and related functions
unnecessary, drop them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
NUMA emulation changes node mappings and thus apicid -> node mapping
needs to be updated accordingly. srat_64 and amdtopology_64 did this
separately; however, all the necessary information is the mapping from
emulated nodes to physical nodes which is available in
emu_nid_to_phys[].
Implement common __apicid_to_node[] transformation in numa_emulation()
and drop duplicate implementations.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
NUMA emulation built physnodes[] array which could only represent
configurations from the physical meminfo and emulated nodes using the
information. There's no reason to take this extra level of
indirection. Update emulation functions so that they operate directly
on numa_meminfo. This simplifies the code and makes emulation layout
behave better with interleaved physical nodes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Both emulation layout functions - split_nodes[_size]_interleave() -
didn't wrap emulated nid while laying out the fake nodes and tried to
avoid interating over the specified number of nodes, which is fragile.
Now that the emulation code generates numa_meminfo, the node memblks
don't need to be consecutive and emulated node IDs can simply wrap.
This makes the code more robust and is necessary for updates to better
handle the cases where the physical nodes are interleaved.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
NUMA emulation code built nodes[] array and had its own registration
path to set up the emulated nodes. Update it such that it generates
emulated numa_meminfo and returns control to initmem_init() and shares
the same registration path with non-emulated cases.
Because {acpi|amd}_fake_nodes() expect nodes[] parameter,
fake_physnodes() now generates nodes[] from numa_meminfo. This will
go away with further updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
NUMA emulation copied physical NUMA configuration into physnodes[] and
used it to reverse-map emulated nodes to physical nodes, which is
unnecessarily convoluted. Build emu_nid_to_phys[] array to map
emulated nids directly to the matching physical nids and use it in
numa_add_cpu().
physnodes[] will be removed with further patches.
- v2: Build failure when CONFIG_DEBUG_PER_CPU_MAPS due to missing
local variable definition fixed. Reported by Ingo.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
* Separate out numa_add_memblk_to() from numa_add_memblk() so that
different numa_meminfo can be used.
* Rename cmdline to emu_cmdline.
* Drop @start/last_pfn from numa_emulation() and use max_pfn directly.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Node distance either used direct node comparison, ACPI PXM comparison
or ACPI SLIT table lookup. This patch implements generic node
distance handling. NUMA init methods can call numa_set_distance() to
set distance between nodes and the common __node_distance()
implementation will report the set distance.
Due to the way NUMA emulation is implemented, the generic node
distance handling is used only when emulation is not used. Later
patches will update NUMA emulation to use the generic distance
mechanism.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
