Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.
v2: Put the check into the right place for CRT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.
The stragglers are:
* i915.force_probe and i915.modeset. Needed before dev_priv is
available. This is fine because the parameters are read-only and never
modified.
* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
I915_STATE_WARN_ON would result in massive and ugly churn. This is
handled by not exposing the parameter via debugfs, and leaving the
parameter writable in sysfs. This may be fixed up in follow-up work.
* i915.inject_probe_failure. Only makes sense in terms of the module,
not the device. This is handled by not exposing the parameter via
debugfs.
v2: Fix uc i915 lookup code (Michał Winiarski)
Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently we only set the DRM_CONNECTOR_POLL_{DISCONNECT,CONNECT}
bits in intel_connector->polled (the base setting), leading to
some confusing looking code to reset drm_connector->polled
(the actual setting) to DRM_CONNECTOR_POLL_HPD. Let's set
intel_connector->polled = DRM_CONNECTOR_POLL_HPD for all hpd
capable connectors, and then we don't need so many special
cases in the hotplug code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205183546.9291-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.
@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}
@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}
@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))
@@
expression C;
@@
- to_intel_connector(&C->base)
+ C
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Move all of haswell_crtc_disable() into the encoder
.post_disable() hooks. Now we're left with just
calling the .disable() and .post_disable() hooks
back to back.
I chose to move the code into the .post_disable() hook instead
of the .disable() hook as most of the sequence is currently
implemented in the .post_disable() hook.
We should collapse it all down to just one hook and then the
encoders can drive the modeset sequence fully. But that may
need some further refactoring as we currently call the
ddi .post_disable() hook from mst code and we can't just
replace that with a call to the ddi .disable() hook.
Should also follow up with similar treatment for the enable
sequence but let's start here where it's easier.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
For the HPD interrupt functionality the HW depends on power wells in the
display core domain to be on. Accordingly when enabling these power
wells the HPD polling logic will force an HPD detection cycle to account
for hotplug events that may have happened when such a power well was
off.
Thus a detect cycle started by polling could start a new detect cycle if
a power well in the display core domain gets enabled during detect and
stays enabled after detect completes. That in turn can lead to a
detection cycle runaway.
To prevent re-triggering a poll-detect cycle make sure we drop all power
references we acquired during detect synchronously by the end of detect.
This will let the poll-detect logic continue with polling (matching the
off state of the corresponding power wells) instead of scheduling a new
detection cycle.
Fixes: 6cfe7ec02e ("drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112125
Reported-and-tested-by: Val Kulkov <val.kulkov@gmail.com>
Reported-and-tested-by: wangqr <wqr.prg@gmail.com>
Cc: Val Kulkov <val.kulkov@gmail.com>
Cc: wangqr <wqr.prg@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028181517.22602-1-imre.deak@intel.com
