Pass physical address of timer block to mxc_timer_init() call, which in
turn does dynamic mapping within the function. Thus, we can avoid using
static mapping in clock drivers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.
This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.
Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The IRQB of S2MPS11 PMIC is wired to XEINT4 (GPX0-4) through pull-up
resistor.
Add interrupt properties and pinctrl configuration to enable RTC wake
alarm of rtc-s5m driver. This also removes a warning:
sec_pmic 4-0066: No interrupt specified, no interrupts
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add nodes for jpeg codec in Exynos5420 SoC.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[k.kozlowski: fixed up minor differences for applying]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes on S3C2416 so they could be easily
referenced by board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice. Move the LVDS bridge to proper existing
i2c_7 node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
PWM output wasn't working because it wasn't hooked up to its pincontrol.
This patch:
- hooks up PWM to its pincontrol, and documents what
the outputs are on the XU3
- switches the LEDs that are on PWM outputs to use PWM
rather than GPIO.
The main effect is that the brightness of the LEDs can be controlled, and
user-mode fan control is enabled via /sys/class/pwm
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes so they could be easily referenced by
Exynos4 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since e4b3d38088 ("phy: exynos-video-mipi: Fix regression by adding
support for PMU regmap") the Exynos PMU driver provides regmap to access
the MIPI DPHY registers. The MIPI DPHY driver accesses this regmap
through syscon phandle.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since e4b3d38088 ("phy: exynos-video-mipi: Fix regression by
adding support for PMU regmap") the Exynos PMU driver provides
regmap to access the MIPI DPHY registers. The MIPI DPHY node uses
a phandle to syscon to get this regmap. The 'reg' field is obsolete.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Replace fixed parent with last parent (obtained with clk_get_parent())
of clocks for devices in mfc and disp power domains. This should improve
behavior if such clocks were reparented by the drivers and new parents
are different than those specified in DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enable CONFIG_SENSORS_PWM_FAN on exynos_defconfig to control fan
power on Odroid-XU3.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using
the same dts for both models. Unfortunately this does not work for the otg
controller, on the M9 this is routed to a micro-usb connector on the outside,
while as on the A1000G-quad it is connected to an usb to sata bridge
(which is not populated on the M9 pcb).
This commit adds a new dts for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand,
sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot.
This commit adds a dts file for the v1.1 pcb with an a33 soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA33 is a core/SDK development board by Sinlinx. The core board
does not have any connectors or pads, other than the pads used to connect
it to the SDK board.
The core board only has the A33 SoC, 2 RAM chips, an eMMC flash chip,
the AXP223 PMIC, and supporting discrete components. eMMC is optional.
The SDK board has a USB host, USB OTG, volume control and home buttons,
audio input/output jacks, a micro-SD slot, camera and SDIO expansion
headers, an LCD connector, and a GPIO expansion header, which has
UARTs, MIPI DSI and I2C available. Only UART0 is enabled though.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A33 adds an additional pinmux option for uart0 on the PB pins.
This was not present on the A23. Nor is it available on the H3,
which does not have the PB pingroup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc2 is mostly used with eMMC flash chips, as an alternative to
raw NAND flash chips. 8 bit mmc is commonly used.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SOCrates has three HPS LEDs that can be turned on/off via gpio.
Use the first one has heartbeat and add the other two as free LEDs.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the enable-method property for the cpu node on socfpga.dtsi and
socfpga_arria10.dtsi. This is for CPU_METHOD_OF_DECLARE to use to enable
the secondary core.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Some of the OMAP based boards e.g. am437x-gp-evm have
the Pixcir touch controller. Enable the related device
driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add an usb_clk node for a23/a33.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
ET-Q8_A33 is A33 based cheap tablet in common Q8 format.
It has 512MB RAM, 4GB Nand, 7" Display, RDA5900P wifi, GSL1680 touch, etc.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Add a dtsi file for use with a33 based boards based on the new
sun8i-a23-a33.dtsi file.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Rename sun8i-a23.dtsi to sun8i-a23-a33.dtsi as the base dtsi for the A33
is 99% the same and add a new sun8i-a23.dtsi including sun8i-a23-a33.dtsi
and setting the few things not shared with the A33 (mbus-clk, pio
compatible and interrupts).
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Register crypto hwmod links only if they are not disabled in DT.
If DT information is missing, enable them only for GP devices.
Before this patch crypto hwmod links were always disabled for all HS
devices and it was not possible to use omap-aes and omap-sham linux
drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[paul@pwsan.com: move the complex IP-block presence heuristics into their
own function to simplify the code; fix some checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this patch function pm_runtime_get_sync() returns 0 even when
some omap subfunction fails. This patch properly propagate error codes
from omap functions back to caller.
This patch fix problem, when loading omap-aes driver in qemu cause
kernel oops.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[paul@pwsan.com: fix a checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without a hwmod for am43xx emif use counting for emif clockdomain does
not happen correctly so it may be shut off by pm code unintentionally.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Avoid entering "RTC-only mode" at poweroff. It is unsupported by most
versions of BeagleBone, and risks hardware damage.
The damaging configuration is having system-power-controller
without ti,pmic-shutdown-controller.
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Johan Hovold <johan@kernel.org>
[Matthijs van Duin: added explanatory comments]
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Fixes: http://bugs.elinux.org/issues/143
Cc: stable@vger.kernel.org # v3.12+
[tony@atomide.com: updated comments with the hardware breaking info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
New system control module layout for omap3 overlooked parts of the am35xx
configuration. Basically the am35xx clocks were not converted to use the
changed offsets, which caused weird boot warnings. The errors were not
fatal so far, so they were not caught earlier. Fixed by applying the
proper offsets for the AM35xx scm clocks.
Fixes: b8845074cf ("ARM: dts: omap3: add minimal l4 bus layout with...")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jeroen Hofstee <linux-arm@myspectrum.nl>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Enable i.MX7D and LS1021A SoC support
- Enable support for WL1271 WIFI/BT, SX8654 I2C touchscreen and PCF8523
RTC, which can be found on Armadeus Systems APF6 and Cubox-i boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbArDAAoJEFBXWFqHsHzOaMoIAJrdhMHWKpTys4OmQOao0qE1
uHCrGHlAcWGy8xgoA617D3PLahP9QMID9GUFxH8cWRa4ifBEybn9nqyQFU/Sp6CM
cwRNXvscupvnPQcZIbpQlJezaBH2pqm43BOWi5b77/ASdh+xad7JFGniOb6P5L2Q
iplE12VVDkg70t3tOh7lHgrRs5I/1DL3/JSCTh7KEEjxr0wBkR68/b3ONP3eqnhP
txa+mW1fh61l3VZ8qzff8T1yvyft/onoqbzfN9BVITlKDrWe3NSM/jalM9h1o5T3
orlj3rLacJhdSpWUtCK+M8BovdaI549wNk7HnDH1lNzawUJ3m8b7Y1uuAfkAhGI=
=DIH7
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
Merge "The i.MX defconfig updates for 4.2" from Shawn Guo:
- Enable i.MX7D and LS1021A SoC support
- Enable support for WL1271 WIFI/BT, SX8654 I2C touchscreen and PCF8523
RTC, which can be found on Armadeus Systems APF6 and Cubox-i boards.
* tag 'imx-defconfig-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: updates for Armadeus Systems APF6 boards
ARM: config: imx_v6_v7_defconfig add imx7d support
ARM: imx_v6_v7_defconfig: Select LS1021A
ARM: imx_v6_v7_defconfig: Enable RTC PCF8523 support
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IRmr
-----END PGP SIGNATURE-----
Merge tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500 and ARM SOC" from Linus Walleij:
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
* tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: define the backupram in the device tree
ARM: ux500: add board documentation
ARM: scu: document Snoop Control Unit DT bindings
STM32 clocksource driver needs to be selected if ARCH_STM32.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "changes for Broadcom SoCs":
- Dan fixes an error path in the BCM63xx SMP code
- Ray adds the relevant Kconfig selects to enable the Broadcom NAND driver on Cygnus
- Kevin provides a change to the Broadcom GISB arbiter driver to make it work with
MIPS-based big-endian STB SoCs (this was a long-standing change that had dependencies on
code in drivers/of/*)
- Gregory enables the use of GPIOLIB for brcmstb SoCs and bumps the number of GPIOs for
these platforms
* tag 'arm-soc/for-4.2/soc-part2' of http://github.com/broadcom/stblinux:
ARM: brcmstb: Add default gpio number
ARM: brcmstb: Select ARCH_WANT_OPTIONAL_GPIOLIB
bus: brcmstb_gisb: Honor the "big-endian" and "native-endian" DT properties
ARM: BCM: Enable NAND support for iProc SoCs
ARM: BCM63xx: fix an error path in bcm63xx_pmb_power_on_cpu()
Merge "This pull request contains a single change" from Florian Fainelli:
- fix the NAND controller node on bcm63138, the original change was a mis-merge that
did not properly parent it to the "ubus" node
* tag 'arm-soc/for-4.2/dts-fixes' of http://github.com/broadcom/stblinux:
ARM: dts: BCM63xx: re-parent NAND controller node
Add 2 new set boards:
- Armada 385 based Linksys boards
- DLink DNS-327L
Update the spi-nor flash compatible strings
Use improved armada spi device tree compatible name for each mvebu SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo3bwACgkQCwYYjhRyO9UxNgCgn5KoYMnx0qzbbmc7rfoyd9g3
IF8An0yb+2EFpP7SBPu41s8rXOATCCTb
=APjz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.2-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v4.2 (part #2)" from Gregory CLEMENT:
Add 2 new set boards:
- Armada 385 based Linksys boards
- DLink DNS-327L
Update the spi-nor flash compatible strings
Use improved armada spi device tree compatible name for each mvebu SoC
* tag 'mvebu-dt-4.2-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: use improved armada spi device tree compatible name for each SoC
ARM: mvebu: dts: Add dts file for DLink DNS-327L
ARM: mvebu: add "jedec,spi-nor" flash compatible binding
ARM: kirkwood: add "jedec,spi-nor" flash compatible binding
ARM: mvebu: add support for the new Armada 385 based Linksys boards
mvebu-mbus: add mv_mbus_dram_info_nooverlap() needed for the new
Marvell crypto driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo26sACgkQCwYYjhRyO9UQ4gCeLb6E7RWXGXtLBXRvRi+1a5Vm
GckAn2a/4vAQExwlDsiqHMsM2Iw9Phc7
=1es8
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-4.2' of git://git.infradead.org/linux-mvebu into next/drivers
Merge "mvebu drivers change for 4.2" from Gregory CLEMENT:
mvebu-mbus: add mv_mbus_dram_info_nooverlap() needed for the new
Marvell crypto driver
* tag 'mvebu-drivers-4.2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: add mv_mbus_dram_info_nooverlap()
Based on the earlier bug fixes branch, which contains six other
patches already merged into 4.1.
wakeup to stacked domains. This allows waking up the device from
suspend to RAM using S3C RTC driver (the RTC on SoC).
The patch should be applied some time ago, unfortunately
it seems it slipped through fingers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BUV3
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-4.1-4' of https://github.com/krzk/linux into fixes
Merge "ARM: EXYNOS: Fix for 4.1, 4th" from Krzysztof Kozlowski:
Fix for Exynos3250 RTC wake-up interrupts after converting PMU
wakeup to stacked domains. This allows waking up the device from
suspend to RAM using S3C RTC driver (the RTC on SoC).
The patch should be applied some time ago, unfortunately
it seems it slipped through fingers.
* tag 'samsung-fixes-4.1-4' of https://github.com/krzk/linux:
ARM: exynos: Fix wake-up interrupts for Exynos3250
Disable unused internal RTC for Mamba from linksys (Armada XP)
And 2 commits fixing regressions on mvebu-mbus:
- the first one for Kirkwood or Orion SoC
- the second one for DMA when the platform have more than 4GB (only
possible on Armada XP as far as I know)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo2BIACgkQCwYYjhRyO9Vf4ACZAUuChGNGu5zOwme4AHCuimp6
TnYAn2n7DjGJ+0aOHCY6qAsVGCUdnda9
=FvVk
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1-3' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for 4.1 (part 3)" from Gregory CLEMENT:
Disable unused internal RTC for Mamba from linksys (Armada XP)
And 2 commits fixing regressions on mvebu-mbus:
- the first one for Kirkwood or Orion SoC
- the second one for DMA when the platform have more than 4GB (only
possible on Armada XP as far as I know)
* tag 'mvebu-fixes-4.1-3' of git://git.infradead.org/linux-mvebu:
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
All ARMv5 and older CPUs invalidate their caches in the early assembly
setup function, prior to enabling the MMU. This is because the L1
cache should not contain any data relevant to the execution of the
kernel at this point; all data should have been flushed out to memory.
This requirement should also be true for ARMv6 and ARMv7 CPUs - indeed,
these typically do not search their caches when caching is disabled (as
it needs to be when the MMU is disabled) so this change should be safe.
ARMv7 allows there to be CPUs which search their caches while caching is
disabled, and it's permitted that the cache is uninitialised at boot;
for these, the architecture reference manual requires that an
implementation specific code sequence is used immediately after reset
to ensure that the cache is placed into a sane state. Such
functionality is definitely outside the remit of the Linux kernel, and
must be done by the SoC's firmware before _any_ CPU gets to the Linux
kernel.
Changing the data cache clean+invalidate to a mere invalidate allows us
to get rid of a lot of platform specific hacks around this issue for
their secondary CPU bringup paths - some of which were buggy.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The A20 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The A10s and A13 have a few SRAM that can be mapped either to a device or
to the CPU, with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The A10 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
This patch reverts commit ccb4ada2f1 ("ARM: dts: sun7i: Add A20 SRAM and
SRAM controller"), commit e6f51e4bd2 ("ARM: dts: sun5i: Add A13 and A10s
SRAM and SRAM controller") and commit 6d92b80f35 ("ARM: dts: sun4i: Add
A10 SRAM and SRAM controller").
The bindings have been changed in the SRAM driver, and we need to
change the DT accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On A80 there are 2 watchdogs, one in the main block, and one in the
R (special) block. We do not have information on the R block watchdog,
other than the register layout is the same, and the interrupt number.
Both are able to reset the whole system.
Add the main watchdog, in case the R block is used for special purposes
like running an RTOS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BananaPro uses uart4 for the default rx/tx pins on the 40 pins connector,
so enable uart4.
Uart2 is also available at the bananapro io-pins, but like on the bananapi
the primary function of the pins is to act as gpios, see:
http://forum.lemaker.org/forum.php?mod=viewthread&tid=10852
Remove the uart2 node, people who want to use uart2 can do so with a
devicetree-overlay.
Signed-off-by: Michael Ring <mail@michael-ring.org>
[hdegoede@redhat.com: Remove uart2 node]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards (e.g. the BananaPro) use alternative pins for uart4, add a pinmux
entry for these.
Signed-off-by: Michael Ring <mail@michael-ring.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display
connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a
bunch of embedded sensors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 8b283c0254 (ARM: exynos4/5: convert pmu wakeup to
stacked domains) changed the Exynos PMU code to use stacked
domains. This has led to a number of interrupt numbers to be
fixed.
In the meantime, support for Exynos 3250 was added, missing
the required change to this platform. This amounts to revert
ace283a04a (ARM: EXYNOS: Fix wrong hwirq of RTC interrupt
for Exynos3250 SoC), as the initial patch was right, just a
bit early...
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Pull ARM fixes from Russell King:
"Three fixes this time around:
- fix a memory leak which occurs when probing performance monitoring
unit interrupts
- fix handling of non-PMD aligned end of RAM causing boot failures
- fix missing syscall trace exit path with syscall tracing enabled
causing a kernel oops in the audit code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8357/1: perf: fix memory leak when probing PMU PPIs
ARM: fix missing syscall trace exit
ARM: 8356/1: mm: handle non-pmd-aligned end of RAM
Two weeks worth of small bug fixes this time, nothing sticking out
this time:
- one defconfig change to adapt to a modified Kconfig symbol
- two fixes for i.MX for backwards compatibility with older DT
files that was accidentally broken
- one regression fix for irq handling on pxa
- three small dt files on omap, and one each for imx and exynos
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2HQg
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Two weeks worth of small bug fixes this time, nothing sticking out
this time:
- one defconfig change to adapt to a modified Kconfig symbol
- two fixes for i.MX for backwards compatibility with older DT files
that was accidentally broken
- one regression fix for irq handling on pxa
- three small dt files on omap, and one each for imx and exynos"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Replace CONFIG_USB_ISP1760_HCD by CONFIG_USB_ISP1760
ARM: imx6: gpc: don't register power domain if DT data is missing
ARM: imx6: allow booting with old DT
ARM: dts: set display clock correctly for exynos4412-trats2
ARM: pxa: pxa_cplds: signedness bug in probe
ARM: dts: Fix WLAN interrupt line for AM335x EVM-SK
ARM: dts: omap3-devkit8000: Fix NAND DT node
ARM: dts: am335x-boneblack: disable RTC-only sleep
ARM: dts: fix imx27 dtb build rule
ARM: dts: imx27: only map 4 Kbyte for fec registers
Out of the brcmstb SoCs that I know, BCM3390 has the largest numbers
of GPIOs, with its
- 320 "peripheral" GPIOs
- 5*32 = 160 UPG GPIOs (counting unused lines, which do get counted)
- 2*32 = 64 UPG AON GPIOs (counting unused lines)
Total: 544
I suspect that the upper limit will only need to be higher in the
future, so set it to 1024.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Select ARCH_WANT_OPTIONAL_GPIOLIB from BRCMSTB to allow GPIOLIB and
GPIO_BRCMSTB to be enabled.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix dts to match what the Linux kernel expects. This works around
touchscreen problems in 4.1 linux on Nokia n900.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed for USB on dm816x-evm.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This ethernet device is used on devkit8000 board.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with
musb_dsps") we need to use the right compatible flag to avoid issues
with FIFO reads.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Fixes: 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge cleanups from Russell King:
* 'for-arm-soc' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: Show proper respect for Heinrich Hertz by using the correct unit for frequency
* Only select sound drivers that build
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nfP3
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v4.2" from Simon Horman:
* Only select sound drivers that build
* tag 'renesas-soc-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: only select sound drivers that build
Remove the generic 8250 config option so that the LPC18xx
specific option gets picked instead.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since commit 100832abf0 ("usb: isp1760: Make HCD support
optional"), CONFIG_USB_ISP1760_HCD is automatically selected when
needed. Enabling that option in the defconfig is now a no-op, and no
longer enables ISP1760 HCD support.
Re-enable the ISP1760 driver in the defconfig by enabling
USB_ISP1760_HOST_ROLE instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It includes a couple of fixes for i.MX6 GPC code to let the new kernel
be able to boot with old DTBs:
- Booting v4.1-rc kernel with old DTBs will fail with a fat warning
(require low-level debug to be seen), due to the adoption of stacked
IRQ domain. The first fix improves the situation by allowing kernel
boot up with old DTBs, although suspend/resume still breaks.
- Booting new kernel with old DTBs that do not have power-domain info
will result in a hang. The second patch fixes the hang by skipping
the kernel power-domain registration if DTB has no power-domain info.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVZalkAAoJEFBXWFqHsHzOk7YH/iQwidJWob015NvrsqUvQlDb
+dIFmUJNFpGqbkLjINDJv0p13lfksuCQ29F/b0R86+sWsRVS/JUKRkVZ1qh83lc9
8ywiTDUqJBEUApwTaVDDqWr6bbYYHC9TdZ/MqJ85hnF2PnwjBS1Vuv+WQuQe/8ru
7LuTzWyqce8u/cYi/0Zs0Vrtmsz5pjhh7Xg1iWXtamJ43v+yqDP/OwZ5BdSkT+P4
J7WWAojVz4iVG4ftNSdJ1CqGuaFP4iMg+HUoS4ecEsyhe6CMdDoq+I2Fuf1aZweS
6clSe/X2HCi7Gspv9oELsNVEci6AfFR/0Ut6LgvSya8AjxZgdu3cmbdDtbPSQ+o=
=dMJE
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "The i.MX fixes for 4.1, 3rd round" from Shawn Guo:
It includes a couple of fixes for i.MX6 GPC code to let the new kernel
be able to boot with old DTBs:
- Booting v4.1-rc kernel with old DTBs will fail with a fat warning
(require low-level debug to be seen), due to the adoption of stacked
IRQ domain. The first fix improves the situation by allowing kernel
boot up with old DTBs, although suspend/resume still breaks.
- Booting new kernel with old DTBs that do not have power-domain info
will result in a hang. The second patch fixes the hang by skipping
the kernel power-domain registration if DTB has no power-domain info.
* tag 'imx-fixes-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: gpc: don't register power domain if DT data is missing
ARM: imx6: allow booting with old DT
- Set display clock correctly for exynos4412-trats2
: fix the following error
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIbBAABAgAGBQJVX+5NAAoJEA0Cl+kVi2xqpMIP8wfc3SQ50eR+6rHmsxoSmxFE
QxAq8g/yQYTXOy3xtm4IF0UQthkeqzpYRwsgROG0Jvg8lbh66LfQrOC9k8H2GMv5
gnFZBeby1DkPU6LA4NEe20VaK0uh84h/OxwoHJTaXUacsUJ4yQvgObGWuazz0kAN
4y2bW0N0MPBWQT2xdm17DOAmECsbR3SievUPPph+s3oRXH3wyQPDB8r/qV1F8LyD
9DjM7z4J1zepVtOno9xgdlP10OCGrLXorJM6rp9b86DLa+RiSQ+BEu42OrhNlMSj
rKScbjldxx11dF8lE0TGo7uo5c6kdgiJgPUhDwanMllpmdGKSnauek4vHHhLrtHJ
oYZTRLRAsRxqzaNzd1FqSqJs45BMkR+VLnXFNNxMNXNn4fx7655Ji0W+CR34b9ko
lo7p7O6bEWzapI57xIt6OR/O+pXaDfRKxAWbejQ1/nLKs29iGDfG+qLVe92a6NKq
5gtO4GVQam+z59ivFqZBjWFjx1OeYBdyDYa5sFSzqtZ+o7tM2JCP65PrfIA5foUm
1OftnwMPVDkpT3haWICDx0mVeHSPvE2d55R6iAnPeAlxEeVTk5/BLlYtsn9wP5eB
o4tfrWTYgVKPNg3KIvE/XkMyGmX7T/asKK6RB8JuVAKPOSJ1ATP0z9cPGScj63Va
2yaKIKGIuOcFyg5KqUI=
=U0hO
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fix for v4.1" from Kukjin Kim:
- Set display clock correctly for exynos4412-trats2
: fix the following error
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: set display clock correctly for exynos4412-trats2
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OIk0
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
* tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7794 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791: add MMCIF max-frequency
ARM: shmobile: r8a7790: add MMCIF max-frequency
ARM: shmobile: bockw dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: henninger dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: bockw-reference dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: koelsch dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: lager dts: Replace "nor-jedec" by "jedec,spi-nor"
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlVmuqQACgkQykllyylKDCEKxgCgl/50lxDs3V9bRw5JUiN0ClM/
lCoAn2OfNpK5w/HmOw57erYuIA0rPQc8
=ulOE
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx into next/dt
Merge "arm: Xilinx Zynq dt patches for v4.2" from Michal Simek:
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
* tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: DT: Use the zynq binding with macb
of: Add vendor prefix for Ceva
PCI: xilinx: Trivial fix in DT example
devicetree: cadence_ttc: Document binding for timer width
ARM: dts: zynq: Fix stdout-path and bootargs
ARM: dts: zynq: Add missing alias node for zybo and parallella
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVX46XAAoJEBvUPslcq6Vzd+cQALB8fPAEVrTedwf+7M02SWEl
0z+lrG+VFusfHjqVj7Me26CjQLJet0Ntq+MGSyiInOpO8XhQI6z77EZHD6AOxfGV
KDcDHoU4vs6UudyzkECkQ+v47cVCoNIV7lj3VnXvxbykSRSDUpg/xvw5Fj6TQpxW
EYY7yOGx096kmtQi1dED1g8cawtsJeb0uRPNm38FzRRPWj5/0+Av5NTAvh7jkd/X
hPSOeWST0cvtrXn3xpX9ZM2g+2O5ZMDOyxn6GDZup4WwgQD3pU/HnySckcKnUjPg
/UWK7Qw/u/eup2cU2TYJLS5SKIm4EPcWb/qht721Yd2kTT0Yn1/RubWvLxbYHcKr
ZFwQ5T5zU0PpoScij4MJuagiEq4sedxkfKbTfckjJgHFubDMiEHV4C7EGkYGDP0i
MLS9YdAGWeb/zQ3gedYbup/9gvD5qjMh8q9EHoWovG8ZInqBmzg7xA0QYkY3Tks1
hClQpv+0KGm8PI9Gz/AYf4wxEFgAUzI7Cqh9m+6LW1z/VmOecCcHg3XKO7JVimtk
baqLo6/dJCtLqlpI4UHNujmfPdCzH1VjITTpfz2FxFdO9MseL2POJ++POwJvgghH
tU1heRVNlSOeYDgWnRChLPyx0Cx/3n5qpfPvumF9W0kpNoOA5dAXkAY979Cm/l46
nSIBsJDsCQJOqBZpqnMF
=MmxV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Andy Simpkins <andy.simpkins@toby-churchill.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support dm9000 network interface in the device tree of devkit8000 board.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We get a NULL pointer dereference on omap3 for thumb2 compiled kernels:
Internal error: Oops: 80000005 [#1] SMP THUMB2
...
[<c046497b>] (_raw_spin_unlock_irqrestore) from [<c0024375>]
(omap3_enter_idle_bm+0xc5/0x178)
[<c0024375>] (omap3_enter_idle_bm) from [<c0374e63>]
(cpuidle_enter_state+0x77/0x27c)
[<c0374e63>] (cpuidle_enter_state) from [<c00627f1>]
(cpu_startup_entry+0x155/0x23c)
[<c00627f1>] (cpu_startup_entry) from [<c06b9a47>]
(start_kernel+0x32f/0x338)
[<c06b9a47>] (start_kernel) from [<8000807f>] (0x8000807f)
The power management related assembly on omaps needs to interact with
ARM mode bootrom code, so we need to keep most of the related assembly
in ARM mode.
Turns out this error is because of missing ENDPROC for assembly code
as suggested by Stephen Boyd <sboyd@codeaurora.org>. Let's fix the
problem by adding ENDPROC in two places to sleep34xx.S.
Let's also remove the now duplicate custom code for mode switching.
This has been unnecessary since commit 6ebbf2ce43 ("ARM: convert
all "mov.* pc, reg" to "bx reg" for ARMv6+").
And let's also remove the comments about local variables, they are
now just confusing after the ENDPROC.
The reason why ENDPROC makes a difference is it sets .type and then
the compiler knows what to do with the thumb bit as explained at:
https://wiki.ubuntu.com/ARM/Thumb2PortingHowto
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Mamba (like the OpenBlocks AX3) doesn't have a crystal
connected to the internal RTC - let's prevent the kernel from
probing it.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: <stable@vger.kernel.org> # v4.0 +
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
parallella - Remove linux,stdout-path.
Use stdout-path to identify kernel console
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
We need to unlock and unmap some resourses before returning.
Fixes: 3f2a43c98d ('ARM: BCM63xx: Add secondary CPU PMB initialization sequence')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The NAND controller is a child node of the UBUS (legacy) bus, not the
AXI (new) bus, re-parent the NAND controller node accordingly. This was
a mistake introduced by a failed merge of this NAND node with other
changes (PMB).
Fixes: b5762cacc4 ("ARM: bcm63138: add NAND DT support")
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Use the new compatible introduced in order to benefit of a wider and
more accurate range of baud rates to be used.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
DNS-327L is a 2-bay NAS with the following specs:
- 512MiB RAM
- 128MiB NAND Flash
- 1 GbE interface (Marvell PHY)
- 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
- 2 internal SATA ports handled by the Armada 370:
uses 2 gpios for power control
- two front 2-color leds (amber + white) for both discs,
controlled by the SoC
- One white LED handled by SoC (USB)
- 3 buttons. Power handled by weltrend, USB and
RESET (on the bottom) are wired via GPIOs
- Unidentified i2c device at address 0x13 (via i2cdetect)
- UART0 providing serial console
- Weltrend MCU serving for RTC, temperature, fan control,
and power button handling interfaced via UART1
(Handled via userspace dns320l-daemon)
Signed-off-by: Andrew Andrianov <andrew@ncrmnt.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
If the devicetree is too old and does not provide the regulator and clocks
for the power domain, we need to avoid registering the power domain.
Otherwise runtime PM will try to control the domain, which will lead to
machine hangs without the proper DT configuration data.
This restores functionality to the kernel 4.0 level if an old DT is
detected, where the power domain is constantly powered on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The GPC rewrite to IRQ domains has been on the premise that it may break
suspend/resume for new kernels on old DT, but otherwise keep things working
from a user perspective. This was an accepted compromise to be able to move
the GIC cleanup forward.
What actually happened was that booting a new kernel on an old DT crashes
before even the console is up, so the user does not even see the warning
that the DT is too old. The warning message suggests that this has been
known before, which is clearly unacceptable.
Fix the early crash by mapping the GPC memory space if the IRQ controller
doesn't claim it. This keeps at least CPUidle and the needed CPU wakeup
workarounds working. With this fixed the system is able to boot up
properly minus the expected suspend/resume breakage.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).
Both boards have:
- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM
gregory.clement@free-electrons.com: use serial0:115200n8 in
stdout-path and remove the bootargs part in the chosen node
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A couple of codec drivers are selected by shmobile platform code,
but depend on I2C, which results in a build error:
sound/soc/codecs/ak4642.c:638:1: warning: data definition has no type or storage class
module_i2c_driver(ak4642_i2c_driver);
^
sound/soc/codecs/ak4642.c:638:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/ak4642.c:638:1: warning: parameter names (without types) in function declaration
sound/soc/codecs/ak4642.c:627:26: warning: 'ak4642_i2c_driver' defined but not used [-Wunused-variable]
This ensures that we do not enable the respective drivers when I2C
is disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch does 'savedefconfig' for exynos_defconfig to remove useless
configs and check its dependencies. Sometimes some configs could be
ignored because of the dependencies even they are enabled in defconfig
file manually. So checking the dependencies would be better.
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enable the Exynos DSI and S6E8AA0 panel for full X11 display on Trats2.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch sets display clock correctly. If Display clock isn't set
correctly then you would find below messages and Display controller
doesn't work correctly.
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
Fixes: abc0b1447d ("drm: Perform basic sanity checks on probed modes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXvpAAAoJEAf03oE53VmQxx0IAMegPIH5rS0NIC+XmwpFnmre
L0bP0dRdKHS5uRxsZfD7F0WF61JiOuLzgX/rIIclnllvvKMPVW+CEs1KnfWVP33u
9FfFIErkGnYeJjs7Lj1j1lb9ESkJfqapMwTfl74mod8QFOT3cgXOiUu8pgHIp2cF
OTR6W5vkv1KoR8E0B4nGv9wZmRBeujtxW+2nIZZVcAglxfOHkJfqlfQ5wCQtdsnU
7K45r4WTbM632hIW5XA3OlzCuuIWs2Hr591aW8PY4KLMPB39HcCV/eTxJMGRbg1Q
4baSQ0xN+DhPfJary0Nc6Y2QXxZWb9y2ElGrqVMlbanCV7xaUGUGYrZ14heRvRs=
=ubIG
-----END PGP SIGNATURE-----
Merge tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Third batch of DT changes for 4.2" from Nicolas Ferre:
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
* tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: remove useless usb clock
ARM: at91/dt: remove useless uhpck clock references from ehci defintions
USB: atmel: update DT bindings documentation
ARM: at91/dt: at91sam9x5: fix usart1 sck pin definition
Enable the USB OHCI driver for Exynos SoCs: S5PV210, Exynos4 family,
Exynos5250, Exynos5440 and Exynos542x/5800 family.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable support for Thermal Monitoring Unit present on Exynos SoCs. This
allows detection of overheat and handling this gracefully.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable drivers for PMICs and MUICs present on Exynos-based devices:
- max14577: charger, fuel gauge (max17040), regulator,
used on: Gear 1, Gear 2,
- max77693: charger, fuel gauge (max17042),
used on: Trats2,
- s5m/s2mps: RTC, clock,
used on: Arndale, Arndale Octa, Gear 1, Gear 2
This allows full usage of charging stack on these devices along with RTC
and 32 kHz clocks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[kgene@kernel.org: savedefconfig]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current Exynos CPU idle driver supports entering AFTR (Arm Off, Top
Running) mode on Exynos3250, Exynos4210 (coupled), Exynos4x12 and
Exynos5250. Enable it in default configuration to reduce energy
consumption.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Cypress All Points Addressable (APA) I2C Trackpad is used in the
Samsung Exynos 5250 Snow Chromebook. Build the driver as a module so
the device is supported.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The I2C GPIO arbitration driver is used on the Exynos5250 Snow Chromebook
to arbitrate the access to a I2C bus by the Application Processor or a EC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many Exynos devices have devices attached to their display ports.
This patch enables the needed Kconfig options to support different
configuration such as simple panel, embedded DisplayPort (eDP) to
LVDS bridges and HDMI displays.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[kgene@kernel.org: savedefconfig]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The rtc-s3c driver supports a range of S3C series Real-Time-Clocks found
on many Samsung SoCs. Build the driver as a module to support these RTC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Build the Generic PWM Samsung driver as a module to support PWM
devices used in platforms with a Samsung SoC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the needed Kconfig options to have support for the ChromeOS EC
I2C transport, I2C tunnel and chardev user-space interface.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the needed kconfig options to have support for Samsung USB 2.0
and USB 3.0 PHY drivers to support the USB PHYs found on Exynos SoCs.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[kgene@kernel.org: savedefconfig]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Maxim max77802 Power Management IC is used on many Exynos machines.
Besides a bunch of regulators, this chip has a Real-Time-Clock (RTC)
and 2-channel 32kHz clock outputs.
Enable the kernel config options to have the drivers for these devices
built as a module.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[kgene@kernel.org: removing useless REGULATOR_MAX77802 config]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Build the spi-s3c64xx driver as a module to have support for
the SPI controller in several Samsung SoCs.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Select ARM_SINGLE_ARMV7M in defconfigs of the converted ARMv7-M
platforms.
[arnd: moved the efm32_defconfig change to the patch that
originally introduces the symbol, to avoid intermittent regression]
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the new config symbol ARM_SINGLE_ARMV7M which groups config
symbols used by modern ARMv7-M platforms. This allows supporting
multiple ARMv7-M platforms in one kernel image. However, a common
kernel image requires the combined platforms to share the same
main memory layout to be bootable.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The newly added zx platform causes a build error when
CONFIG_THUMB2_KERNEL is enabled:
arch/arm/mach-zx/headsmp.S:16: Error: invalid immediate for address calculation (value = 0x00000004)
I'm assuming that the ROM code that is calling these entry
points runs in ARM mode, so there would be another problem
in the same file, and we can solve both problems at once
by adding a '.arm' statement that will make zx_resume_jump
and zx_secondary_startup both be built as ARM code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Jun Nie <jun.nie@linaro.org>
"base_irq" needs to be signed for the error handling to work. Also we
can remove the initialization because we re-assign it later.
Fixes: aa8d6b73ea ('ARM: pxa: pxa_cplds: add lubbock and mainstone IO')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iSye
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/cleanup
Merge "First batch of cleanup for 4.2" from Alexandre Belloni:
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
* tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-omap3logic.c Getting a .dts file for v4.2
board-omap3pandora.c Got a .dts file for v4.1
board-rx51-*.c Needs /proc/atags support for user space
I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.
Also, few patches to clean-up the usage of Linux generic
macros:
- Use define for console loglevel
- Use const for struct irq_domain_ops
- Use PTR_ERR_OR_ZERO instead of PTR_RET
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AVB2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Merge "Clean-up for omaps for v4.2 merge window" from Tony Lindgren:
Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.
The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.
This leaves us with only the following board-*.c files:
BOARD REASON NEEDED
board-ldp.c Still used in RMKs boot test system
board-omap3logic.c Getting a .dts file for v4.2
board-omap3pandora.c Got a .dts file for v4.1
board-rx51-*.c Needs /proc/atags support for user space
I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.
Also, few patches to clean-up the usage of Linux generic
macros:
- Use define for console loglevel
- Use const for struct irq_domain_ops
- Use PTR_ERR_OR_ZERO instead of PTR_RET
* tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: OMAP2+: Remove legacy booting support for Beagleboards
ARM: OMAP2+: Remove legacy booting support for Overo
ARM: OMAP2+: Remove legacy booting support for cm-t35
to making omap1 support multiarch. After this series we still need to
make omap1 use the common clock framework and fix up the drivers to not
rely on includes from mach and plat directories.
Note that this branch depends on a GPIO driver fix in v4.1-rc3
d2d05c65c4 ("gpio: omap: Fix regression for MPUIO interrupts").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FVxF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/omap1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge fixed up omap1 sparse irq support for v4.2 from Tony Lindgren:
Add support for CONFIG_SPARSE_IRQ for omap1. This takes us a bit closer
to making omap1 support multiarch. After this series we still need to
make omap1 use the common clock framework and fix up the drivers to not
rely on includes from mach and plat directories.
Note that this branch depends on a GPIO driver fix in v4.1-rc3
d2d05c65c4 ("gpio: omap: Fix regression for MPUIO interrupts").
* tag 'omap-for-v4.2/omap1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: Fix section mismatch warnings for omap_cfg_reg
ARM: OMAP1: Fix randconfig builds if ARCH_OMAP15XX not selected
ARM: OMAP1: Change interrupt numbering for sparse IRQ
ARM: omap1: Switch to use MULTI_IRQ
ARM: OMAP1: Switch to use generic irqchip in preparation for sparse IRQ
ARM: OMAP1: Move UART defines to prepare for sparse IRQ
Merge mach-bcm changes from Florian Fainelli:
This pull request contains the following changes:
- Rafal adds an additional fault code to be ignored by the kernel on BCM5301X SoC
- BCM63138 SMP support which:
* common code to control the PMB bus, to be shared with a reset
controller driver in drivers/reset
* secondary CPU initialization sequence using PMB helpers
* small changes suggested by Russell King to allow platforms to disable VFP
* tag 'arm-soc/for-4.2/soc-take2' of http://github.com/broadcom/stblinux:
ARM: BCM63xx: Add SMP support for BCM63138
ARM: vfp: Add vfp_disable for problematic platforms
ARM: vfp: Add include guards
ARM: BCM63xx: Add secondary CPU PMB initialization sequence
ARM: BCM63xx: Add Broadcom BCM63xx PMB controller helpers
ARM: BCM5301X: Ignore another (BCM4709 specific) fault code
The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This is cleary used after init time too for example for
configuring UART wake-up events during runtime. This fixes
section mismatch warnings for randconfig builds that happen
because __init_or_module.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the omap1 SPARSE_IRQ changes mach/irqs.h is no longer
automatically included. Turns out now we rely on ARCH_OMAP15XX
including hardware.h from memory.h, so without ARCH_OMAP15XX
we get build failures.
As we have legacy drivers still relying on these indirect
includes, let's not add more mach includes to the drivers.
Those have to be removed anyways for multiplatform support.
Let's fix up mach-omap1 to include soc.h where cpu_is_omap
checks are done, and common.h for board-*.c files.
But let's keep the indirect memory.h include for now to avoid
unnecessary churn in the drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for booting the secondary CPU on BCM63138, this involves:
- locating the bootlut to write the reset vector
- powering up the second CPU when we need to using the DT-supplied PMB
references
- disabling VFP when enabled such that we can keep having SMP
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some platforms might not be able to fully utilize VFP when e.g: one CPU
out of two in a SMP complex lacks a VFP unit. Adding code to migrate
task to the CPU which has a VFP unit would be cumbersome and not
performant, instead, just add the ability to disable VFP.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The sequence to initialize a secondary CPU using the BCM63138 PMB is
extremely specific and represents much more code than any other on-chip
peripheral (AHCI, USB 3.0 or integrated Ethernet switch), as such we
keep that code local and utilize Device Tree to lookup all the resources
we need from the CPU device tree node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add defconfig for Linux on Vybrid (vf610) on the secondary Cortex-
M4 CPU. The use of a XIP image has been tested which needs to be
loaded (e.g. using the custom m4boot loader) to the end of the
available RAM at address 0x8f000000. The Cortex-M4 has a code-alias
which makes sure that the instructions get fetched through the code
bus (alias starts at 0x00800000 => 0x80800000 in system address).
Hence, to get optimal performance, use 0x0f000000 as XIP_PHYS_ADDR.
This address is additionally shifted by the length of the minimal
loader which is inserted by m4boot. Currently, this offset is 0x80.
The standard DRAM base address is configured to 0x8C000000, which
gives the Cortex-M4 48MiB of RAM.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Disable BeagleBone black RTC-only sleep mode because of hardare
related issues
- Fix NAND on Devkit8000
- Fix WLAN interrupt line on AM335x EVM-SK
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x3Wr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Few minimal omap device tree fixes for v4.1-rc series" from Tony Lindgren:
- Disable BeagleBone black RTC-only sleep mode because of hardare
related issues
- Fix NAND on Devkit8000
- Fix WLAN interrupt line on AM335x EVM-SK
* tag 'omap-for-v4.1/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix WLAN interrupt line for AM335x EVM-SK
ARM: dts: omap3-devkit8000: Fix NAND DT node
ARM: dts: am335x-boneblack: disable RTC-only sleep
This patch allows to build the Kernel for Vybrid (VF6xx) SoC
when ARMv7-M CPU is selected. The resulting image runs on the
secondary Cortex-M4 core. This core has equally access to all
peripherals as the main Cortex-A5 core. However, there is no
resource control mechanism, hence when both cores are used
simultaneously, orthogonal device tree's are required.
The boot CPU is dependent on the SoC variant. The available
boards use mostly variants where the Cortex-A5 is the primary
and hence the boot CPU. Booting the secondary Cortex-M4 CPU
needs SoC specific registers written. There is no in kernel
support for this right now, a external userspace utility
called "m4boot" can be used to boot the kernel:
m4boot xipImage initramfs.cpio.lzo vf610m4-colibri.dtb
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This introduces a new top level config symbol ARM_SINGLE_ARMV7M
for non-MMU, ARMv7-M platforms. It also support multiple ARMv7-M
platforms in one kernel image since the cores share the same
basic memory layout and interrupt controller. However, this works
only if the combined platforms also have a similar (main) memory
layout.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the needless differences between MMU/!MMU addruart calls.
This allows to use the same addruart macro on SoC level. Useful
for SoC consisting of multiple CPUs with and without MMU such as
Freescale Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds an initial device tree to run Linux on the Cortex-M4 on
the Vybrid based Colibri VF61 module.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Broadcom ARM devices seem to generate some fault once per boot. We
already have an ignoring handler for BCM4707/BCM4708, but BCM4709
generates different code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C6Wl
-----END PGP SIGNATURE-----
Merge tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "Berlin DT changes for v4.2" from Sebastian Hesselbarth:
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
* tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin:
Documentation: bindings: update the berlin chip and system ctrl doc
Documentation: bindings: move the Berlin clock documentation
Documentation: bindings: move the Berlin pinctrl documentation
Documentation: bindings: move the Berlin reset documentation
Documentation: bindings: update the Berlin controllers documentation
Documentation: bindings: berlin: consider our dt bindings as unstable
ARM: dts: berlin: relicense the BG2CD Google Chromecast dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2cd dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2 Sony NSZ-GS7 dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2 dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2Q Marvell DMP dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2q dtsi under GPLv2/X11
This removes the deprecacted marco, PTR_RET and changes the
functions that use this marco in their return statement to
instead use the non deprecacted function, PTR_ERR_OR_ZERO
for the file devices.c.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The beaglebone family of boards contain two I2C busses enabled.
The first one with a baseboard identification EEPROM and a
cape I2C bus.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this patch does the following:
1: adds DT node for fixed oscillator.
2: adds DT node entries for ov2659 sensor
3: adds remote-endpoint entry for VPFE.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This device is an industrial PC based on
AM335x SoC.
[ balbi@ti.com : updated to fit current mainline ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 wakeup takes place with iodaisy chain. enable the wakeup pin.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: tabify uart pins properly while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add voice audio card which is used for telephony on gta04 board.
gtm601 codec is UMTS modem with pcm interface which get samples from
microphone and provide data from other party side. Use simple audio card
to describe audio card.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart1 is used for connecting to wilink8 bluetooth subsystem.
add the needed muxes and definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable mmc3 used for wlan and uart3 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable omap-hdq for battery fuel gauge access.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes two calls to the deprecated marco,PTR_RET in
the files,fb.c and pmu.c for the functions,omap_init_vrfb
and omap_init_pmu respectfully. Furthermore these are now
replaced by calling the correctly non deprecacted function,
PTR_ERR_OR_ZERO in both functions.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
<linux/printk.h> provides macros for console log level, let's use it
instead of numbers.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the technical reference manual for AM35xx system
controller module (SCM) PADCONFS core registers are divided in two
regions: 0x48002030..0x48002268 and 0x480025d8..0x480025fc.
First region is the same for all omap3 SoC and is described in omap3.dtsi.
The second region is the same as in omap34xx (see omap34xx.dtsi)
and omap35xx. The patch adds missing description for the second region.
This patch was tested on AM3517.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO
controllers are numbered from 0 on AM335x and from 1 on OMAP. But when
the configuration for the TI WLAN controllers was converted from
platform data to device tree, this detail was overlooked, as 10 boards
were using OMAP with the WL12xx and WL18xx controllers, and only one
was based on AM335x.
This invalid configuration prevents the WL1271 module on the AM335x
EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver.
The DTS must be corrected to use the correct GPIO controller.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nand-ecc-opt and device-width properties to enable nand support on
Devkit8000.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: http://bugs.elinux.org/issues/143
Entering RTC-only sleep is only properly supported on early prototypes series
(pre-A6) of the BeagleBone Black. Since rev (A6A), which include all production
versions, it is not support at due to.
(rev A6) enable of the 3v3b regulator moved from LDO2 to LDO4 (3v3a)
side-effect: 3v3b rail remains on in sleep-mode (also in off-mode when battery-powered)
(rev A6A) am335x vdds supply moved from LDO3 to LDO1
side-effect: vdds remains supplied in sleep-mode
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.
Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.
Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some devices are using the MMC1 pins 4..8 as GPIO pins, and in
this case they need to be configured for 1.8V IO voltage if not
done by the bootloader as otherwise some devices like smsc911x
won't work properly.
Let's also make sure this register is saved and restored for
idle.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change interrupt numbering for sparse IRQ. We do this using
a fixed offset until we can drop irqs.h once all it's users
have been updated.
Note that this depends on the GPIO fix for the MPUIO IRQs
"gpio: omap: Fix regression for MPUIO interrupts".
Also note that this patch adds some extra irq alloc warnings
that will go away when we stop calling irq_alloc_descs
in gpio-omap.c with a follow-up patch.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to get a bit further with SPARSE_IRQ and
MULTIARCH support.
Note that we now also rename omap_irq_flags to omap_l2_irq
as that's the omap_irq_flags naming is confusing. It just
contains the interrupt number for the l2 irq.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's set up things ready for enabling sparse IRQ and remove the
omap_read/write usage.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
