This is preparation for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Next transfer data size of "push" and "pop" had calculated on shared function.
But it was not readable code.
This patch divided it into for push, and for pop.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch gathered fsi_stream_xxx() functions in order to make it readable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All DAPM routes are configured via device tree, and there is no need in
DAPM route structures in board file.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the standard logging macros and use dev_ variants where we can, also
reporting error codes whenever we report an error. These changes (the
error codes in particular) make it noticeably easier to figure out what
went wrong just from the basic dmesg output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Use the dai_link's dai_fmt attribute to setup the DAI format instead of doing
this manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into for-3.4
A reasonable amount of new development is causing fiddly merge conflicts
between different resource management changes (mostly fixing bugs in
resource management due to noticing things while doing enhancements in
the same area).
Linux 3.3-rc2
.. several days delayed. No reason, I just didn't think of it.
This patch implements device tree support for Tegra boards with ALC5632
codec.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For later wm_hubs devices we have much less need to keep the biases up
even when using single ended line outputs so flag idle_bias_off for
everything except the WM8993 and WM8994.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the same pm_ops for all system suspend and resume paths. This isn't
ideal for suspend to disk with older CODECs as we'll suspend and then
resume the CODEC before powering off all of which takes a long time due
to VMID ramps but it's very simple to implement and for modern CODECs the
overhead should be minimal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The runtime PM core no longer requires any callbacks so don't provide
empty ones for it any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator has no power control itself and so shouldn't cause a
power up of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care if any action is taken immediately so let the PM
core defer things if it wants to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modern devices allow systems to enable and disable individual supplies on
the device, allowing additional power saving by switching off regulators
which power portions of the device which are not currently in use. Add a
new SND_SOC_DAPM_REGULATOR_SUPPLY widget type factoring out the code for
managing such widgets from individual drivers.
The widget name will be used as the supply name when requesting the
regulator from the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
As per discussion we can safely ignore the 8 and 16 bit sample
sizes when applying the msbits constraint.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In wm2000_i2c_probe(), if we take the true branch in
"
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
"
then we'll release_firmware(fw) at the 'err_fw' label. But we've already
done that just a few lines above. That's a use-after-free bug.
This patch restructures the code so that we always call
release_firmware(fw) before leaving the function, but only ever call
it once.
This means that we have to initialize 'fw' to NULL since some paths
may now end up calling it without having called request_firmware(),
but since request_firmware() deals gracefully with NULL pointers, we
are fine if we just NULL initialize it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To print a value of type size_t one should use %zd, not %d.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build warning when CONFIG_HOTPLUG is not set.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
CC sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to table based DAPM and control init.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
