Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 replaces the IETF draft for PIE
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Random dropping of packets to achieve latency control may
introduce outlier situations where packets are dropped too
close to each other or too far from each other. This can
cause the real drop percentage to temporarily deviate from
the intended drop probability. In certain scenarios, such
as a small number of simultaneous TCP flows, these
deviations can cause significant deviations in link
utilization and queuing latency.
RFC 8033 suggests using a derandomization mechanism to avoid
these deviations.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation scales the local alpha and beta
variables in the calculate_probability function by the same
amount for all values of drop probability below 1%.
RFC 8033 suggests using additional cases for auto-tuning
alpha and beta when the drop probability is less than 1%.
In order to add more auto-tuning cases, MAX_PROB must be
scaled by u64 instead of u32 to prevent underflow when
scaling the local alpha and beta variables in the
calculate_probability function.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 suggests an initial value of 150 milliseconds for
the maximum time allowed for a burst of packets.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 suggests a default value of 15 milliseconds for the
update interval.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 suggests a default value of 15 milliseconds for the
target queue delay.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 recommends a value of 16384 bytes for the queue
threshold.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot found out that running BPF_PROG_TEST_RUN with repeat=0xffffffff
makes process unkillable. The problem is that when CONFIG_PREEMPT is
enabled, we never see need_resched() return true. This is due to the
fact that preempt_enable() (which we do in bpf_test_run_one on each
iteration) now handles resched if it's needed.
Let's disable preemption for the whole run, not per test. In this case
we can properly see whether resched is needed.
Let's also properly return -EINTR to the userspace in case of a signal
interrupt.
This is a follow up for a recently fixed issue in bpf_test_run, see
commit df1a2cb7c7 ("bpf/test_run: fix unkillable
BPF_PROG_TEST_RUN").
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 9060cb719e ("net: crypto set sk to NULL when af_alg_release.")
fixed a use-after-free in sockfs_setattr() when an AF_ALG socket is
closed concurrently with fchownat(). However, it ignored that many
other proto_ops::release() methods don't set sock->sk to NULL and
therefore allow the same use-after-free:
- base_sock_release
- bnep_sock_release
- cmtp_sock_release
- data_sock_release
- dn_release
- hci_sock_release
- hidp_sock_release
- iucv_sock_release
- l2cap_sock_release
- llcp_sock_release
- llc_ui_release
- rawsock_release
- rfcomm_sock_release
- sco_sock_release
- svc_release
- vcc_release
- x25_release
Rather than fixing all these and relying on every socket type to get
this right forever, just make __sock_release() set sock->sk to NULL
itself after calling proto_ops::release().
Reproducer that produces the KASAN splat when any of these socket types
are configured into the kernel:
#include <pthread.h>
#include <stdlib.h>
#include <sys/socket.h>
#include <unistd.h>
pthread_t t;
volatile int fd;
void *close_thread(void *arg)
{
for (;;) {
usleep(rand() % 100);
close(fd);
}
}
int main()
{
pthread_create(&t, NULL, close_thread, NULL);
for (;;) {
fd = socket(rand() % 50, rand() % 11, 0);
fchownat(fd, "", 1000, 1000, 0x1000);
close(fd);
}
}
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function tc_dump_chain() obtains and releases block->lock on each iteration
of its inner loop that dumps all chains on block. Outputting chain template
info is fast operation so locking/unlocking mutex multiple times is an
overhead when lock is highly contested. Modify tc_dump_chain() to only
obtain block->lock once and dump all chains without releasing it.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using tcf_walker->stop flag to determine when tcf_walker->fn() was called
at least once is unreliable. Some classifiers set 'stop' flag on error
before calling walker callback, other classifiers used to call it with NULL
filter pointer when empty. In order to prevent further regressions, extend
tcf_walker structure with dedicated 'nonempty' flag. Set this flag in
tcf_walker->fn() implementation that is used to check if classifier has
filters configured.
Fixes: 8b64678e0a ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Metadata pointer is only initialized for action TCA_TUNNEL_KEY_ACT_SET, but
it is unconditionally dereferenced in tunnel_key_init() error handler.
Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
Fixes: ee28bb56ac ("net/sched: fix memory leak in act_tunnel_key_init()")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
parameter state in the tcp_sacktag_bsearch() is not used.
So, it can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We have no more in tree users of switchdev_port_attr_get() after
d0e698d57a ("Merge branch 'net-Get-rid-of-switchdev_port_attr_get'")
so completely remove the function signature and body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
Here's the main bluetooth-next pull request for the 5.1 kernel.
- Fixes & improvements to mediatek, hci_qca, btrtl, and btmrvl HCI drivers
- Fixes to parsing invalid L2CAP config option sizes
- Locking fix to bt_accept_enqueue()
- Add support for new Marvel sd8977 chipset
- Various other smaller fixes & cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_output() frees skb when it fails (see, for example,
ip_finish_output2), so it must not be freed in this case.
Fixes: 3bd0b15281 ("bpf: add handling of BPF_LWT_REROUTE to lwt_bpf.c")
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip l add dev tun type gretap key 1000
Non-tunnel-dst ip tunnel device can send packet through lwtunnel
This patch provide the tun_inf dst cache support for this mode.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lwtunnel_state is not init the dst_cache Which make the
ip_md_tunnel_xmit can't use the dst_cache. It will lookup
route table every packets.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch enables returning 'type' in msghdr for records that are
retrieved with MSG_PEEK in recvmsg. Further it prevents records peeked
from socket from getting clubbed with any other record of different
type when records are subsequently dequeued from strparser.
For each record, we now retain its type in sk_buff's control buffer
cb[]. Inside control buffer, record's full length and offset are already
stored by strparser in 'struct strp_msg'. We store record type after
'struct strp_msg' inside 'struct tls_msg'. For tls1.2, the type is
stored just after record dequeue. For tls1.3, the type is stored after
record has been decrypted.
Inside process_rx_list(), before processing a non-data record, we check
that we must be able to return back the record type to the user
application. If not, the decrypted records in tls context's rx_list is
left there without consuming any data.
Fixes: 692d7b5d1f ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use percpu allocation for the ipv6.icmp_sk.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply use icmpv6_sk_exit() when inet_ctl_sock_create() fail
in icmpv6_sk_init().
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply use icmp_sk_exit() when inet_ctl_sock_create() fail in icmp_sk_init().
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an uninitialised return value error in
ila_xlat_nl_cmd_flush.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 6c4128f658 ("rhashtable: Remove obsolete...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The metadata_dst is not init the dst_cache which make the
ip_md_tunnel_xmit can't use the dst_cache. It will lookup
route table every packets.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is no longer necessary after eca59f6915 ("net: Remove support for bridge bypass ndos from stacked devices")
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when act_skbedit was converted to use RCU in the data plane, we added an
error path, but we forgot to drop the action refcount in case of failure
during a 'replace' operation:
# tc actions add action skbedit ptype otherhost pass index 100
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 1 bind 0
# tc actions replace action skbedit ptype otherhost drop index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action skbedit
total acts 1
action order 0: skbedit ptype otherhost pass
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'params_new' allocation failed,
also when the action is being replaced.
Fixes: c749cdda90 ("net/sched: act_skbedit: don't use spinlock in the data path")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4e8ddd7f17 ("net: sched: don't release reference on action
overwrite"), the error path of all actions was converted to drop refcount
also when the action was being overwritten. But we forgot act_ipt_init(),
in case allocation of 'tname' was not successful:
# tc action add action xt -j LOG --log-prefix hello index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "hello" index 100
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 1 bind 0
# tc action replace action xt -j LOG --log-prefix world index 100
tablename: mangle hook: NF_IP_POST_ROUTING
target: LOG level warning prefix "world" index 100
RTNETLINK answers: Cannot allocate memory
We have an error talking to the kernel
# tc action show action xt
total acts 1
action order 0: tablename: mangle hook: NF_IP_POST_ROUTING
target LOG level warning prefix "hello"
index 100 ref 2 bind 0
Ensure we call tcf_idr_release(), in case 'tname' allocation failed, also
when the action is being replaced.
Fixes: 4e8ddd7f17 ("net: sched: don't release reference on action overwrite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce dev_change_proto_down_generic, a generic ndo_change_proto_down
implementation, which sets the netdev carrier state according to proto_down.
This adds the ability to set protodown on vxlan and macvlan devices in a
generic way for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_pkt_len_init expects transport_header to be set for GSO packets.
Patch [1] skips transport_header validation for GSO packets that don't
have network_header set at the moment of calling virtio_net_hdr_to_skb,
and allows them to pass into the stack. After patch [2] no placeholder
value is assigned to transport_header if dissection fails, so this patch
adds a check to the place where the value of transport_header is used.
[1] https://patchwork.ozlabs.org/patch/1044429/
[2] https://patchwork.ozlabs.org/patch/1046122/
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pointer is RCU protected, so proper primitives should be used.
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This reverts commit 5a2de63fd1 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e26 ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e26 ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has check NULL on kmem_cache_create on failure in kcm_init,
no need use SLAB_PANIC to panic the system.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I thought header search paths to tools/include(/uapi) were unneeded,
but it looks like a build error occurs depending on the compiler.
Commit 303a339f30 ("bpfilter: remove extra header search paths for
bpfilter_umh") reintroduced the build error fixed by commit ae40832e53
("bpfilter: fix a build err").
Apology for the breakage, and thanks to Guenter for reporting this.
Fixes: 303a339f30 ("bpfilter: remove extra header search paths for bpfilter_umh")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455 ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before derefencing the encap pointer, commit e7cc082455 ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455 ("udp: Support for error handlers of tunnels with arbitrary destination port")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 029a374348 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a374348 ("udp6: cleanup stats accounting in recvmsg()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tcindex filter, it is too late to initialize the
net pointer in tcf_exts_validate(), as tcf_exts_get_net()
requires a non-NULL net pointer. We can just move its
initialization into tcf_exts_init(), which just requires
an additional parameter.
This makes the code in tcindex_alloc_perfect_hash()
prettier.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e0 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
c72219b75f introduced tpacket_set_protocol that parses the Ethernet L2
header and sets skb->protocol if it's unset. It is no longer needed
since the introduction of packet_parse_headers. In case of SOCK_RAW and
unset skb->protocol, packet_parse_headers asks the driver to tell the
protocol number, and it's implemented for all Ethernet devices. As the
old function supported only Ethernet, no functionality is lost.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket was created with socket(AF_PACKET, SOCK_RAW, 0), the
protocol number is unavailable. Try to ask the driver to extract it from
the L2 header in order for skb_try_probe_transport_header to succeed.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit introduced parse_protocol callback which should
extract the protocol number from the L2 header. Make all Ethernet
devices support it.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the socket was created with socket(AF_PACKET, SOCK_RAW, 0),
skb->protocol will be unset, __skb_flow_dissect() will fail, and
skb_probe_transport_header() will fall back to the offset_hint, making
the resulting skb_transport_offset incorrect.
If, however, there is no transport header in the packet,
transport_header shouldn't be set to an arbitrary value.
Fix it by leaving the transport offset unset if it couldn't be found, to
be explicit rather than to fill it with some wrong value. It changes the
behavior, but if some code relied on the old behavior, it would be
broken anyway, as the old one is incorrect.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* the massive patch series for multi-BSSID support, I ended up
applying that through a side branch to record some details
* CSA improvements
* HE (802.11ax) updates to Draft 3.3
* strongly typed element iteration/etc. to make such code more
readable - this came up in particular in multi-BSSID
* rhashtable conversion patches from Herbert
Along, as usual, with various fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=SM9w
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have, of note:
* the massive patch series for multi-BSSID support, I ended up
applying that through a side branch to record some details
* CSA improvements
* HE (802.11ax) updates to Draft 3.3
* strongly typed element iteration/etc. to make such code more
readable - this came up in particular in multi-BSSID
* rhashtable conversion patches from Herbert
Along, as usual, with various fixes and improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
-----BEGIN PGP SIGNATURE-----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=JEqH
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support VLAN filtering being enabled/disabled on a
bridge, while having other ports being non bridge port members, we need
to support the ndo_vlan_rx_{add,kill}_vid callbacks in order to make
sure the non-bridge ports can continue receiving VLAN tags, even when
the switch is globally configured to do ingress/egress VID checking.
Since we can call dsa_port_vlan_{add,del} with a bridge_dev pointer
NULL, we now need to check that in these two functions.
We specifically deal with two possibly problematic cases:
- creating a bridge VLAN entry while there is an existing VLAN device
claiming that same VID
- creating a VLAN device while there is an existing bridge VLAN entry
with that VID
Those are both resolved with returning -EBUSY back to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN devices on top of a DSA network device which is already part of a
bridge and with said bridge being VLAN aware should not be allowed to be
enslaved into that bridge. For one, this duplicates functionality
offered by the VLAN aware bridge which supports tagged and untagged VLAN
frames processing and it would make things needlessly complex to e.g.:
propagate FDB/MDB accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bd ("sctp: avoid refreshing heartbeat timer too often")
Reported-by: Marcin Stojek <marcin.stojek@nokia.com>
Tested-by: Marcin Stojek <marcin.stojek@nokia.com>
Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forwarded packets enter the tx path through ieee80211_add_pending_skb,
which skips the ieee80211_skb_resize call.
Fixes WARN_ON in ccmp_encrypt_skb and resulting packet loss.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rhashtable_walk_init function has been obsolete for more than
two years. This patch finally converts its last users over to
rhashtable_walk_enter and removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code in mesh_path_add tries to handle the case where a duplicate
entry is added to the rhashtable by doing a lookup after a failed
insertion. It also tries to handle races by repeating the insertion
should the lookup fail.
This is now unnecessary as we have rhashtable API functions that can
directly return the mathcing object.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, we may want to transport higher bandwidth data
through vendor events, and in that case sending it multicast
is a bad idea. Allow vendor events to be unicast.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some buggy APs keep the CSA IE in probes after the channel
switch was completed and can silence us for no good reason.
Apply quiet mode only from beacons. If there is real channel
switch going on, we will see the beacon anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, due to some buggy APs that continue to include
CSA IEs after the switch, we ignore CSA to same channel.
However, some other APs may do CSA to self in order to have
immediate quiet. Allow it. Do it only for beacons.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to track further the CSA beacons, for example
to compensate for buggy APs that change the beacon count or quiet
mode during CSA flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_vendor_radiotap was read from the beginning
of the skb->data regardless of the existence of other
elements in radiotap that would cause it to move to another
position. Fix this by taking into account where it really
should be.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we receive a beacon without CSA IE while we are in
the middle of channel switch - abort the operation.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018 REVmd of the spec introduces the max channel switch time
element which is optionally included in beacons/probes when there
is a channel switch / extended channel switch element.
The value represents the maximum delay between the time the AP
transmitted the last beacon in current channel and the expected
time of the first beacon in the new channel, in TU.
Parse the value and pass it to the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends the NL80211_CMD_ASSOCIATE event case to report
NL80211_ATTR_REQ_IE similarly to what is already done with the
NL80211_CMD_CONNECT events if the driver provides this information. In
practice, this adds (Re)Association Request frame information element
reporting to mac80211 drivers for the cases where user space SME is
used.
This provides more information for user space to figure out which
capabilities were negotiated for the association. For example, this can
be used to determine whether HT, VHT, or HE is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch is to use eth_broadcast_addr() to assign broadcast address
insetad of memset().
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.
So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
clang warns about overflowing the data[] member in the struct pnpipehdr:
net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds]
if (hdr->data[4] == PEP_IND_READY)
^ ~
include/net/phonet/pep.h:66:3: note: array 'data' declared here
u8 data[1];
Using a flexible array member at the end of the struct avoids the
warning, but since we cannot have a flexible array member inside
of the union, each index now has to be moved back by one, which
makes it a little uglier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2019-02-21
1) Don't do TX bytes accounting for the esp trailer when sending
from a request socket as this will result in an out of bounds
memory write. From Martin Willi.
2) Destroy xfrm_state synchronously on net exit path to
avoid nested gc flush callbacks that may trigger a
warning in xfrm6_tunnel_net_exit(). From Cong Wang.
3) Do an unconditionally clone in pfkey_broadcast_one()
to avoid a race when freeing the skb.
From Sean Tranchetti.
4) Fix inbound traffic via XFRM interfaces across network
namespaces. We did the lookup for interfaces and policies
in the wrong namespace. From Tobias Brunner.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Report erspan version field to userspace in ip6gre_fill_info just for
erspan_v6 tunnels. Moreover report IFLA_GRE_ERSPAN_INDEX only for
erspan version 1.
The issue can be triggered with the following reproducer:
$ip link add name gre6 type ip6gre local 2001::1 remote 2002::2
$ip link set gre6 up
$ip -d link sh gre6
14: grep6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1448 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre6 2001::1 peer 2002::2 promiscuity 0 minmtu 0 maxmtu 0
ip6gre remote 2002::2 local 2001::1 hoplimit 64 encaplimit 4 tclass 0x00 flowlabel 0x00000 erspan_index 0 erspan_ver 0 addrgenmode eui64
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report erspan version field to userspace in ipgre_fill_info just for
erspan tunnels. The issue can be triggered with the following reproducer:
$ip link add name gre1 type gre local 192.168.0.1 remote 192.168.1.1
$ip link set dev gre1 up
$ip -d link sh gre1
13: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/gre 192.168.0.1 peer 192.168.1.1 promiscuity 0 minmtu 0 maxmtu 0
gre remote 192.168.1.1 local 192.168.0.1 ttl inherit erspan_ver 0 addrgenmode eui64 numtxqueues 1 numrxqueues 1
Fixes: f551c91de2 ("net: erspan: introduce erspan v2 for ip_gre")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the bridge no longer calling switchdev_port_attr_get() to obtain
the supported bridge port flags from a driver but instead trying to set
the bridge port flags directly and relying on driver to reject
unsupported configurations, we can effectively get rid of
switchdev_port_attr_get() entirely since this was the only place where
it was called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bridge code and the drivers to check for
bridge port(s) flags at the time we try to set them, there is no need
for a get() -> set() sequence anymore and
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all switchdev drivers have been converted to check the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS flags and report flags that they
do not support accordingly, we can migrate the bridge code to try to set
that attribute first, check the results and then do the actual setting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for removing SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT,
add support for a function that processes the
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS and
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attributes and returns not
supported for any flag set, since DSA does not currently support
toggling those bridge port attributes (yet).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches work by learning the MAC address for each attached station by
monitoring traffic from each station. When a station sends a packet,
the switch records which port the MAC address is connected to.
With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4. The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.
With IPv6 networking, the situation is rather different. Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted. This multicast needs to reach the intended
station in order for the neighbour to be discovered.
Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale. This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.
Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports. As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network. However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.
The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.
This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge. This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 844cf763fb ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_ip4_multicast_mrd_rcv only return 0 and -ENOMSG,
no other negative value
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This case block has been terminated by a return, so not need
a switch fall-through
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error code isn't set on this path so it would result in returning
ERR_PTR(0) and a NULL dereference in the caller.
Fixes: 18d3eefb17 ("net: sched: refactor tcf_block_find() into standalone functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only way to clear the forwarding cache was to delete the
entries one by one using the MRT_DEL_MFC socket option or to destroy and
recreate the socket.
Create a new socket option which with the use of optional flags can
clear any combination of multicast entries (static or not static) and
multicast vifs (static or not static).
Calling the new socket option MRT_FLUSH with the flags MRT_FLUSH_MFC and
MRT_FLUSH_VIFS will clear all entries and vifs on the socket except for
static entries.
Signed-off-by: Callum Sinclair <callum.sinclair@alliedtelesis.co.nz>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid sending attributes related to recovery:
DEVLINK_ATTR_HEALTH_REPORTER_GRACEFUL_PERIOD and
DEVLINK_ATTR_HEALTH_REPORTER_AUTO_RECOVER in reply to
DEVLINK_CMD_HEALTH_REPORTER_GET for a reporter which didn't register a
recover operation.
These parameters can't be configured on a reporter that did not provide
a recover operation, thus not needed to return them.
Fixes: 7afe335a8b ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename devlink health attributes for better reflect the attributes use.
Add COUNT prefix on error counter attribute and recovery counter
attribute.
Fixes: 7afe335a8b ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-D devices are identified by their PCI IDs in the pnet table. In
order to make usage of the pnet table more consistent for users, this
patch adds this form of identification for ib devices as well.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds namespace support to the pnet table code. Each network
namespace gets its own pnet table. Infiniband and smcd device pnetids
can only be modified in the initial namespace. In other namespaces they
can still be used as if they were set by the underlying hardware.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, users can only set pnetids for netdevs and ib devices in the
pnet table. This patch adds support for smcd devices to the pnet table.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device does not have a pnetid, users can set a temporary pnetid for
said device in the pnet table. This patch reworks the pnet table to make
it more flexible. Multiple entries with the same pnetid but differing
devices are now allowed. Additionally, the netlink interface now sends
each mapping from pnetid to device separately to the user while
maintaining the message format existing applications might expect. Also,
the SMC data structure for ib devices already has a pnetid attribute.
So, it is used to store the user defined pnetids. As a result, the pnet
table entries are only used for netdevs.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use local variable pflags from the beginning of function
smcr_tx_sndbuf_nonempty
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_poll() returns with mask bit EPOLLPRI if the connection urg_state
is SMC_URG_VALID. Since SMC_URG_VALID is zero, smc_poll signals
EPOLLPRI errorneously if called in state SMC_INIT before the connection
is created, for instance in a non-blocking connect scenario.
This patch switches to non-zero values for the urg states.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Fixes: de8474eb9d ("net/smc: urgent data support")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a RCU critical section around rt6_info->from deference, and
proper annotation.
Fixes: 4ed591c8ab ("net/ipv6: Allow onlink routes to have a device mismatch if it is the default route")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must access rt6_info->from under RCU read lock: move the
dereference under such lock, with proper annotation.
v1 -> v2:
- avoid using multiple, racy, fetch operations for rt->from
Fixes: a68886a691 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAlxu23wTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi04sB/9/Lm694io6coIW/8mTVjKs9iF7+AkA
V11Pu3VHnp8okcNs3iSv6rtbPgLrONP5fg7OC9xAzzsEjA8kitnV7kC0RunzuUiw
BnZcE0v5Eh4NB34DW4w4I0JDkEH75zlsw/ar8HDvgxTw9hCgV56n1oic+MkqAuiL
5TwBjuLL5Nl4tA9djcMtHhBy3u+jQXAEDJ9tiKFBhzQOPo73N2IyZyY+Kz3qqygV
XLWvpmW6PA9jJt8pUGRCqpahaYAY7+cyzOUJbqdRUpeESVl/2Epr7zJZo9LHQtsE
GympS5weYMg6xLoZHQXvLbb77E/SlXkeVyNzBw7LnV6us2PS4tbgSt2J
=alOG
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.0-rc8' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two bug fixes for old issues, both marked for stable"
* tag 'ceph-for-5.0-rc8' of git://github.com/ceph/ceph-client:
ceph: avoid repeatedly adding inode to mdsc->snap_flush_list
libceph: handle an empty authorize reply
This reverts commit e2ce367488.
It turns out that the sock destructor xsk_destruct was needed after
all. The cleanup simplification broke the skb transmit cleanup path,
due to that the umem was prematurely destroyed.
The umem cannot be destroyed until all outstanding skbs are freed,
which means that we cannot remove the umem until the sk_destruct has
been called.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
(cherry picked from commit 033b228e7f)
When tcindex_destroy() destroys all the filter results in
the perfect hash table, it invokes the walker to delete
each of them. However, results with class==0 are skipped
in either tcindex_walk() or tcindex_delete(), which causes
a memory leak reported by kmemleak.
This patch fixes it by skipping the walker and directly
deleting these filter results so we don't miss any filter
result.
As a result of this change, we have to initialize exts->net
properly in tcindex_alloc_perfect_hash(). For net-next, we
need to consider whether we should initialize ->net in
tcf_exts_init() instead, before that just directly test
CONFIG_NET_CLS_ACT=y.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 8015d93ebd)
tcindex_destroy() invokes tcindex_destroy_element() via
a walker to delete each filter result in its perfect hash
table, and tcindex_destroy_element() calls tcindex_delete()
which schedules tcf RCU works to do the final deletion work.
Unfortunately this races with the RCU callback
__tcindex_destroy(), which could lead to use-after-free as
reported by Adrian.
Fix this by migrating this RCU callback to tcf RCU work too,
as that workqueue is ordered, we will not have use-after-free.
Note, we don't need to hold netns refcnt because we don't call
tcf_exts_destroy() here.
Fixes: 27ce4f05e2 ("net_sched: use tcf_queue_work() in tcindex filter")
Reported-by: Adrian <bugs@abtelecom.ro>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several u->addr and u->path users are not holding any locks in
common with unix_bind(). unix_state_lock() is useless for those
purposes.
u->addr is assign-once and *(u->addr) is fully set up by the time
we set u->addr (all under unix_table_lock). u->path is also
set in the same critical area, also before setting u->addr, and
any unix_sock with ->path filled will have non-NULL ->addr.
So setting ->addr with smp_store_release() is all we need for those
"lockless" users - just have them fetch ->addr with smp_load_acquire()
and don't even bother looking at ->path if they see NULL ->addr.
Users of ->addr and ->path fall into several classes now:
1) ones that do smp_load_acquire(u->addr) and access *(u->addr)
and u->path only if smp_load_acquire() has returned non-NULL.
2) places holding unix_table_lock. These are guaranteed that
*(u->addr) is seen fully initialized. If unix_sock is in one of the
"bound" chains, so's ->path.
3) unix_sock_destructor() using ->addr is safe. All places
that set u->addr are guaranteed to have seen all stores *(u->addr)
while holding a reference to u and unix_sock_destructor() is called
when (atomic) refcount hits zero.
4) unix_release_sock() using ->path is safe. unix_bind()
is serialized wrt unix_release() (normally - by struct file
refcount), and for the instances that had ->path set by unix_bind()
unix_release_sock() comes from unix_release(), so they are fine.
Instances that had it set in unix_stream_connect() either end up
attached to a socket (in unix_accept()), in which case the call
chain to unix_release_sock() and serialization are the same as in
the previous case, or they never get accept'ed and unix_release_sock()
is called when the listener is shut down and its queue gets purged.
In that case the listener's queue lock provides the barriers needed -
unix_stream_connect() shoves our unix_sock into listener's queue
under that lock right after having set ->path and eventual
unix_release_sock() caller picks them from that queue under the
same lock right before calling unix_release_sock().
5) unix_find_other() use of ->path is pointless, but safe -
it happens with successful lookup by (abstract) name, so ->path.dentry
is guaranteed to be NULL there.
earlier-variant-reviewed-by: "Paul E. McKenney" <paulmck@linux.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 121d57af30 ("gso: validate gso_type in GSO handlers") added
gso_type validation to existing gso_segment callback functions, to
filter out illegal and potentially dangerous SKB_GSO_DODGY packets.
Convert tunnels that now call inet_gso_segment and ipv6_gso_segment
directly to have their own callbacks and extend validation to these.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed. However, the Linux bridge code believes that
the port is in disabled mode.
If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode. If it is brought up and then added to the bridge,
it will be in disabled mode.
This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge. Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.
Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA. See
e47172ab7e ("rocker: put port in FORWADING state after leaving bridge")
Fixes: b73adef677 ("net: dsa: integrate with SWITCHDEV for HW bridging")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix suspend and resume in mt76x0u USB driver, from Stanislaw
Gruszka.
2) Missing memory barriers in xsk, from Magnus Karlsson.
3) rhashtable fixes in mac80211 from Herbert Xu.
4) 32-bit MIPS eBPF JIT fixes from Paul Burton.
5) Fix for_each_netdev_feature() on big endian, from Hauke Mehrtens.
6) GSO validation fixes from Willem de Bruijn.
7) Endianness fix for dwmac4 timestamp handling, from Alexandre Torgue.
8) More strict checks in tcp_v4_err(), from Eric Dumazet.
9) af_alg_release should NULL out the sk after the sock_put(), from Mao
Wenan.
10) Missing unlock in mac80211 mesh error path, from Wei Yongjun.
11) Missing device put in hns driver, from Salil Mehta.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
sky2: Increase D3 delay again
vhost: correctly check the return value of translate_desc() in log_used()
net: netcp: Fix ethss driver probe issue
net: hns: Fixes the missing put_device in positive leg for roce reset
net: stmmac: Fix a race in EEE enable callback
qed: Fix iWARP syn packet mac address validation.
qed: Fix iWARP buffer size provided for syn packet processing.
r8152: Add support for MAC address pass through on RTL8153-BD
mac80211: mesh: fix missing unlock on error in table_path_del()
net/mlx4_en: fix spelling mistake: "quiting" -> "quitting"
net: crypto set sk to NULL when af_alg_release.
net: Do not allocate page fragments that are not skb aligned
mm: Use fixed constant in page_frag_alloc instead of size + 1
tcp: tcp_v4_err() should be more careful
tcp: clear icsk_backoff in tcp_write_queue_purge()
net: mv643xx_eth: disable clk on error path in mv643xx_eth_shared_probe()
qmi_wwan: apply SET_DTR quirk to Sierra WP7607
net: stmmac: handle endianness in dwmac4_get_timestamp
doc: Mention MSG_ZEROCOPY implementation for UDP
mlxsw: __mlxsw_sp_port_headroom_set(): Fix a use of local variable
...
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2019-02-19
An update from ieee802154 for *net-next*
Another quite quite cycle in the ieee802154 subsystem.
Peter did a rework of the IP frag queue handling to make it use rbtree and get
in line with the core IPv4 and IPv6 implementatiosn in the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
when capable check failed, dev_put should
be call before return -EACCES.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->queue_mapping already have read access, via __sk_buff->queue_mapping.
This patch allow BPF tc qdisc clsact write access to the queue_mapping via
tc_cls_act_is_valid_access. Also handle that the value NO_QUEUE_MAPPING
is not allowed.
It is already possible to change this via TC filter action skbedit
tc-skbedit(8). Due to the lack of TC examples, lets show one:
# tc qdisc add dev ixgbe1 clsact
# tc filter add dev ixgbe1 ingress matchall action skbedit queue_mapping 5
# tc filter list dev ixgbe1 ingress
The most common mistake is that XPS (Transmit Packet Steering) takes
precedence over setting skb->queue_mapping. XPS is configured per DEVICE
via /sys/class/net/DEVICE/queues/tx-*/xps_cpus via a CPU hex mask. To
disable set mask=00.
The purpose of changing skb->queue_mapping is to influence the selection of
the net_device "txq" (struct netdev_queue), which influence selection of
the qdisc "root_lock" (via txq->qdisc->q.lock) and txq->_xmit_lock. When
using the MQ qdisc the txq->qdisc points to different qdiscs and associated
locks, and HARD_TX_LOCK (txq->_xmit_lock), allowing for CPU scalability.
Due to lack of TC examples, lets show howto attach clsact BPF programs:
# tc qdisc add dev ixgbe2 clsact
# tc filter add dev ixgbe2 egress bpf da obj XXX_kern.o sec tc_qmap2cpu
# tc filter list dev ixgbe2 egress
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Each tls context maintains two cipher contexts (one each for tx and rx
directions). For each tls session, the constants such as protocol
version, ciphersuite, iv size, associated data size etc are same for
both the directions and need to be stored only once per tls context.
Hence these are moved from 'struct cipher_context' to 'struct
tls_prot_info' and stored only once in 'struct tls_context'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aligns IP defragmenation logic in 6lowpan with that
of IPv4 and IPv6: see
commit d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6 defrag")
Modifying ip_defrag selftest seemed like an overkill, as I suspect
most kernel test setups do not have 6lowpan hwsim enabled. So I ran
the following code/script manually:
insmod ./mac802154_hwsim.ko
iwpan dev wpan0 set pan_id 0xbeef
ip link add link wpan0 name lowpan0 type lowpan
ip link set wpan0 up
ip link set lowpan0 up
iwpan dev wpan1 set pan_id 0xbeef
ip netns add foo
iwpan phy1 set netns name foo
ip netns exec foo ip link add link wpan1 name lowpan1 type lowpan
ip netns exec foo ip link set wpan1 up
ip netns exec foo ip link set lowpan1 up
ip -6 addr add "fb01::1/128" nodad dev lowpan0
ip -netns foo -6 addr add "fb02::1/128" nodad dev lowpan1
ip -6 route add "fb02::1/128" dev lowpan0
ip -netns foo -6 route add "fb01::1/128" dev lowpan1
# then in term1:
ip netns exec foo bash
./udp_stream -6
# in term2:
./udp_stream -c -6 -H fb02::1
# pr_warn_once showed that the code changed by this patch
# was invoked.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Follow up patch to fix a compilation warning in a recent IPVS fix:
098e13f5b2 ("ipvs: fix dependency on nf_defrag_ipv6").
2) Bogus ENOENT error on flush after rule deletion in the same batch,
reported by Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RPS not work for DSA devices since the 'skb_get_hash'
will always get the invalid hash for dsa tagged packets.
"[PATCH] tag_mtk: add flow_dissect callback to the ops struct"
introduced the flow_dissect callback to get the right hash for
MTK tagged packet. Tag_dsa and tag_edsa also need to implement
the callback.
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_lock_bh() is used in table_path_del() but rcu_read_unlock()
is used for unlocking. Fix it by using spin_unlock_bh() instead
of rcu_read_unlock() in the error handling case.
Fixes: b4c3fbe636 ("mac80211: Use linked list instead of rhashtable walk for mesh tables")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot found out that running BPF_PROG_TEST_RUN with repeat=0xffffffff
makes process unkillable. The problem is that when CONFIG_PREEMPT is
enabled, we never see need_resched() return true. This is due to the
fact that preempt_enable() (which we do in bpf_test_run_one on each
iteration) now handles resched if it's needed.
Let's disable preemption for the whole run, not per test. In this case
we can properly see whether resched is needed.
Let's also properly return -EINTR to the userspace in case of a signal
interrupt.
See recent discussion:
http://lore.kernel.org/netdev/CAH3MdRWHr4N8jei8jxDppXjmw-Nw=puNDLbu1dQOFQHxfU2onA@mail.gmail.com
I'll follow up with the same fix bpf_prog_test_run_flow_dissector in
bpf-next.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for you net-next
tree:
1) Missing NFTA_RULE_POSITION_ID netlink attribute validation,
from Phil Sutter.
2) Restrict matching on tunnel metadata to rx/tx path, from wenxu.
3) Avoid indirect calls for IPV6=y, from Florian Westphal.
4) Add two indirections to prepare merger of IPV4 and IPV6 nat
modules, from Florian Westphal.
5) Broken indentation in ctnetlink, from Colin Ian King.
6) Patches to use struct_size() from netfilter and IPVS,
from Gustavo A. R. Silva.
7) Display kernel splat only once in case of racing to confirm
conntrack from bridge plus nfqueue setups, from Chieh-Min Wang.
8) Skip checksum validation for layer 4 protocols that don't need it,
patch from Alin Nastac.
9) Sparse warning due to symbol that should be static in CLUSTERIP,
from Wei Yongjun.
10) Add new toggle to disable SDP payload translation when media
endpoint is reachable though the same interface as the signalling
peer, from Alin Nastac.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The authorize reply can be empty, for example when the ticket used to
build the authorizer is too old and TAG_BADAUTHORIZER is returned from
the service. Calling ->verify_authorizer_reply() results in an attempt
to decrypt and validate (somewhat) random data in au->buf (most likely
the signature block from calc_signature()), which fails and ends up in
con_fault_finish() with !con->auth_retry. The ticket isn't invalidated
and the connection is retried again and again until a new ticket is
obtained from the monitor:
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
Let TAG_BADAUTHORIZER handler kick in and increment con->auth_retry.
Cc: stable@vger.kernel.org
Fixes: 5c056fdc5b ("libceph: verify authorize reply on connect")
Link: https://tracker.ceph.com/issues/20164
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
instance = alloc(size, GFP_KERNEL)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*ev) + ev->num_hndl * sizeof(struct hci_comp_pkts_info)
to :
struct_size(ev, handles, ev->num_hndl)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After moving an XFRM interface to another namespace it stays associated
with the original namespace (net in `struct xfrm_if` and the list keyed
with `xfrmi_net_id`), allowing processes in the new namespace to use
SAs/policies that were created in the original namespace. For instance,
this allows a keying daemon in one namespace to establish IPsec SAs for
other namespaces without processes there having access to the keys or IKE
credentials.
This worked fine for outbound traffic, however, for inbound traffic the
lookup for the interfaces and the policies used the incorrect namespace
(the one the XFRM interface was moved to).
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch addresses the fact that there are drivers, specifically tun,
that will call into the network page fragment allocators with buffer sizes
that are not cache aligned. Doing this could result in data alignment
and DMA performance issues as these fragment pools are also shared with the
skb allocator and any other devices that will use napi_alloc_frags or
netdev_alloc_frags.
Fixes: ffde7328a3 ("net: Split netdev_alloc_frag into __alloc_page_frag and add __napi_alloc_frag")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP handlers are not very often stressed, we should
make them more resilient to bugs that might surface in
the future.
If there is no packet in retransmit queue, we should
avoid a NULL deref.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
soukjin bae reported a crash in tcp_v4_err() handling
ICMP_DEST_UNREACH after tcp_write_queue_head(sk)
returned a NULL pointer.
Current logic should have prevented this :
if (seq != tp->snd_una || !icsk->icsk_retransmits ||
!icsk->icsk_backoff || fastopen)
break;
Problem is the write queue might have been purged
and icsk_backoff has not been cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets an error message in extack when the number of qdisc
handles exceeds the maximum. Also the error-code ENOSPC is more
appropriate than ENOMEM in this situation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reported-by: Li Shuang <shuali@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver does not support ethtool flash update operation
call into devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink flash update command. Advanced NICs have firmware
stored in flash and often cryptographically secured. Updating
that flash is handled by management firmware. Ethtool has a
flash update command which served us well, however, it has two
shortcomings:
- it takes rtnl_lock unnecessarily - really flash update has
nothing to do with networking, so using a networking device
as a handle is suboptimal, which leads us to the second one:
- it requires a functioning netdev - in case device enters an
error state and can't spawn a netdev (e.g. communication
with the device fails) there is no netdev to use as a handle
for flashing.
Devlink already has the ability to report the firmware versions,
now with the ability to update the firmware/flash we will be
able to recover devices in bad state.
To enable updates of sub-components of the FW allow passing
component name. This name should correspond to one of the
versions reported in devlink info.
v1: - replace target id with component name (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that filter is not NULL before passing it to tcf_walker->fn()
callback in cls_cgroup_walk(). This can happen when cls_cgroup_change()
failed to set first filter.
Fixes: ed76f5edcc ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that filter is not NULL before passing it to tcf_walker->fn()
callback. This can happen when mall_change() failed to offload filter to
hardware.
Fixes: ed76f5edcc ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in route4_walk() to unify tp->walk() behavior among
classifier implementations.
Fixes: ed76f5edcc ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some classifiers set arg->stop in their implementation of tp->walk() API
when empty. Most of classifiers do not adhere to that convention. Do not
set arg->stop in fw_walk() to unify tp->walk() behavior among classifier
implementations.
Fixes: ed76f5edcc ("net: sched: protect filter_chain list with filter_chain_lock mutex")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing skb_put_data() and skb_trim() instead of open-coding them,
with the skb_put_data() first so that logically, `skb` still contains the
data to be copied in its data..tail area when skb_put_data() reads it.
This change on its own is a cleanup, and it is also necessary for potential
future integration of skbuffs with things like KASAN.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hook tracepoints at the end of functions that
update a neigh entry. neigh_update gets an additional
tracepoint to trace the update flags and old and new
neigh states.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal here is to trace neigh state changes covering all possible
neigh update paths. Plus have a specific trace point in neigh_update
to cover flags sent to neigh_update.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) numerous libbpf API improvements, from Andrii, Andrey, Yonghong.
2) test all bpf progs in alu32 mode, from Jiong.
3) skb->sk access and bpf_sk_fullsock(), bpf_tcp_sock() helpers, from Martin.
4) support for IP encap in lwt bpf progs, from Peter.
5) remove XDP_QUERY_XSK_UMEM dead code, from Jan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-02-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix lockdep false positive in bpf_get_stackid(), from Alexei.
2) several AF_XDP fixes, from Bjorn, Magnus, Davidlohr.
3) fix narrow load from struct bpf_sock, from Martin.
4) mips JIT fixes, from Paul.
5) gso handling fix in bpf helpers, from Willem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's confusing to call PTR_ERR(v). The PTR_ERR() function is basically
a fancy cast to long so it makes you wonder, was IS_ERR() intended? But
that doesn't make sense because vcc_walk() doesn't return error
pointers.
This patch doesn't affect runtime, it's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_SNDBUF and SO_RCVBUF (and their *BUFFORCE version) may overflow or
underflow their input value. This patch aims at providing explicit
handling of these extreme cases, to get a clear behaviour even with
values bigger than INT_MAX / 2 or lower than INT_MIN / 2.
For simplicity, only SO_SNDBUF and SO_SNDBUFFORCE are described here,
but the same explanation and fix apply to SO_RCVBUF and SO_RCVBUFFORCE
(with 'SNDBUF' replaced by 'RCVBUF' and 'wmem_max' by 'rmem_max').
Overflow of positive values
===========================
When handling SO_SNDBUF or SO_SNDBUFFORCE, if 'val' exceeds
INT_MAX / 2, the buffer size is set to its minimum value because
'val * 2' overflows, and max_t() considers that it's smaller than
SOCK_MIN_SNDBUF. For SO_SNDBUF, this can only happen with
net.core.wmem_max > INT_MAX / 2.
SO_SNDBUF and SO_SNDBUFFORCE are actually designed to let users probe
for the maximum buffer size by setting an arbitrary large number that
gets capped to the maximum allowed/possible size. Having the upper
half of the positive integer space to potentially reduce the buffer
size to its minimum value defeats this purpose.
This patch caps the base value to INT_MAX / 2, so that bigger values
don't overflow and keep setting the buffer size to its maximum.
Underflow of negative values
============================
For negative numbers, SO_SNDBUF always considers them bigger than
net.core.wmem_max, which is bounded by [SOCK_MIN_SNDBUF, INT_MAX].
Therefore such values are set to net.core.wmem_max and we're back to
the behaviour of positive integers described above (return maximum
buffer size if wmem_max <= INT_MAX / 2, return SOCK_MIN_SNDBUF
otherwise).
However, SO_SNDBUFFORCE behaves differently. The user value is
directly multiplied by two and compared with SOCK_MIN_SNDBUF. If
'val * 2' doesn't underflow or if it underflows to a value smaller
than SOCK_MIN_SNDBUF then buffer size is set to its minimum value.
Otherwise the buffer size is set to the underflowed value.
This patch treats negative values passed to SO_SNDBUFFORCE as null, to
prevent underflows. Therefore negative values now always set the buffer
size to its minimum value.
Even though SO_SNDBUF behaves inconsistently by setting buffer size to
the maximum value when passed a negative number, no attempt is made to
modify this behaviour. There may exist some programs that rely on using
negative numbers to set the maximum buffer size. Avoiding overflows
because of extreme net.core.wmem_max values is the most we can do here.
Summary of altered behaviours
=============================
val : user-space value passed to setsockopt()
val_uf : the underflowed value resulting from doubling val when
val < INT_MIN / 2
wmem_max : short for net.core.wmem_max
val_cap : min(val, wmem_max)
min_len : minimal buffer length (that is, SOCK_MIN_SNDBUF)
max_len : maximal possible buffer length, regardless of wmem_max (that
is, INT_MAX - 1)
^^^^ : altered behaviour
SO_SNDBUF:
+-------------------------+-------------+------------+----------------+
| CONDITION | OLD RESULT | NEW RESULT | COMMENT |
+-------------------------+-------------+------------+----------------+
| val < 0 && | | | No overflow, |
| wmem_max <= INT_MAX/2 | wmem_max*2 | wmem_max*2 | keep original |
| | | | behaviour |
+-------------------------+-------------+------------+----------------+
| val < 0 && | | | Cap wmem_max |
| INT_MAX/2 < wmem_max | min_len | max_len | to prevent |
| | | ^^^^^^^ | overflow |
+-------------------------+-------------+------------+----------------+
| 0 <= val <= min_len/2 | min_len | min_len | Ordinary case |
+-------------------------+-------------+------------+----------------+
| min_len/2 < val && | val_cap*2 | val_cap*2 | Ordinary case |
| val_cap <= INT_MAX/2 | | | |
+-------------------------+-------------+------------+----------------+
| min_len < val && | | | Cap val_cap |
| INT_MAX/2 < val_cap | min_len | max_len | again to |
| (implies that | | ^^^^^^^ | prevent |
| INT_MAX/2 < wmem_max) | | | overflow |
+-------------------------+-------------+------------+----------------+
SO_SNDBUFFORCE:
+------------------------------+---------+---------+------------------+
| CONDITION | BEFORE | AFTER | COMMENT |
| | PATCH | PATCH | |
+------------------------------+---------+---------+------------------+
| val < INT_MIN/2 && | min_len | min_len | Underflow with |
| val_uf <= min_len | | | no consequence |
+------------------------------+---------+---------+------------------+
| val < INT_MIN/2 && | val_uf | min_len | Set val to 0 to |
| val_uf > min_len | | ^^^^^^^ | avoid underflow |
+------------------------------+---------+---------+------------------+
| INT_MIN/2 <= val < 0 | min_len | min_len | No underflow |
+------------------------------+---------+---------+------------------+
| 0 <= val <= min_len/2 | min_len | min_len | Ordinary case |
+------------------------------+---------+---------+------------------+
| min_len/2 < val <= INT_MAX/2 | val*2 | val*2 | Ordinary case |
+------------------------------+---------+---------+------------------+
| INT_MAX/2 < val | min_len | max_len | Cap val to |
| | | ^^^^^^^ | prevent overflow |
+------------------------------+---------+---------+------------------+
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
that could prevent clients from reclaiming state after a kernel upgrade.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcZzZHAAoJECebzXlCjuG+EOsQALVuwSJqQh4GUVMSBYzL6Ov4
SfinB8LJ8/1HwngSvRB3xQ4HiOtpFSNkjzfFYE7epy6augY8tRRnHGbnlHbsG5vI
wQqTR6PbSq2mupgpi2WGRlRh521SDOi8V49fplUC+FuV7dJT/wm0hgdKsHCPHPX4
TEYPglsvG6PLu5IcAofNac9PVZH21s3yVIKvqd6yifED5lhopdNw210s5DtzvugI
g2JgHOhTfana+xQS/cJ1U8JHbbpM7jwOXAJ7IWD8k4GXdAW03X6jNOcseudcBTQY
qSL33//6Xdu0r0uI21z4ZWxSWCOtt8YvnbMoG4EBqh3DpKbUpExh8j4eIyNPSuSF
Y/8iAVJ9KWYhWO+IVPqvHVXz4mCIDK+f7iJ/m+lLjOQmWkpp6koeUDjKs4k9zBUC
mbGTOrh0TJzXvKWKEU5Qy7meZVJGUpV+9ca+cDs5XN7Xa3blTp+5VrRVeDgKO5Kx
OF3Y3IBOWhqN7+kEH98RvdZAmtbO0zg02IEIHOMPxH69JU8o0EsEni1LXsqDJrRi
sLVYXvLwdPLfkqSjpI8xNeaoFXeelopx8Re+2oNEFIEvsfeT5XikbQHoqgFJNsyk
hz7PHwuyGjc6NJRRSBUKYouWKPP4rrM7ZiOSyIEDYIIwyhBirpjrECaHzdi3D5j+
xUyFGMF5F3wk1fdQHPfD
=NopI
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.0-2' of git://linux-nfs.org/~bfields/linux
Pull more nfsd fixes from Bruce Fields:
"Two small fixes, one for crashes using nfs/krb5 with older enctypes,
one that could prevent clients from reclaiming state after a kernel
upgrade"
* tag 'nfsd-5.0-2' of git://linux-nfs.org/~bfields/linux:
sunrpc: fix 4 more call sites that were using stack memory with a scatterlist
Revert "nfsd4: return default lease period"
- Make sure Send CQ is allocated on an existing compvec
- Properly check debugfs dentry before using it
- Don't use page_file_mapping() after removing a page
-----BEGIN PGP SIGNATURE-----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=28v+
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.0-4' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull more NFS client fixes from Anna Schumaker:
"Three fixes this time.
Nicolas's is for xprtrdma completion vector allocation on single-core
systems. Greg's adds an error check when allocating a debugfs dentry.
And Ben's is an additional fix for nfs_page_async_flush() to prevent
pages from accidentally getting truncated.
Summary:
- Make sure Send CQ is allocated on an existing compvec
- Properly check debugfs dentry before using it
- Don't use page_file_mapping() after removing a page"
* tag 'nfs-for-5.0-4' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Don't use page_file_mapping after removing the page
rpc: properly check debugfs dentry before using it
xprtrdma: Make sure Send CQ is allocated on an existing compvec
When enabled, the sip_external_media logic will leave SDP
payload untouched when it detects that interface towards INVITEd
party is the same with the one towards media endpoint.
The typical scenario for this logic is when a LAN SIP agent has more
than one IP address (uses a different address for media streams than
the one used on signalling stream) and it also forwards calls to a
voice mailbox located on the WAN side. In such case sip_direct_media
must be disabled (so normal calls could be handled by the SIP
helper), but media streams that are not traversing this router must
also be excluded from address translation (e.g. call forwards).
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes the following sparse warnings:
net/ipv4/netfilter/ipt_CLUSTERIP.c:867:23: warning:
symbol 'cip_netdev_notifier' was not declared. Should it be static?
Fixes: 5a86d68bcf ("netfilter: ipt_CLUSTERIP: fix deadlock in netns exit routine")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When CONFIG_IP_VS_IPV6 is not defined, build produced this warning:
net/netfilter/ipvs/ip_vs_ctl.c:899:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret = 0;
^~~
Fix this by moving the declaration of 'ret' in the CONFIG_IP_VS_IPV6
section in the same function.
While at it, drop its unneeded initialisation.
Fixes: 098e13f5b2 ("ipvs: fix dependency on nf_defrag_ipv6")
Reported-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
rt6_cache_allowed_for_pmtu() checks for rt->from presence, but
it does not access the RCU protected pointer. We can use
rcu_access_pointer() and clean-up the code a bit. No functional
changes intended.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
