As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-By: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Check for correct return status in function -
qla4_8xxx_minidump_pex_dma_read
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Updated driver with new opcode (RDDFE, RDMDIO and POLLWR) which are
added with latest firmware minidump template
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Issue:
Driver holds rom-lock for too long during reset recovery.
During adapter reset testing, it was found that the driver
holds the rom-lock for too long, because of which other
drivers fail to acquire the rom-lock, leading to reset
failures.
The primary cause is, in the bootstrap code, while
holding the rom-lock, the driver checks if the peg is
halted, causing a 2 second contention.
Fix:
When a reset recovery starts, the driver deduces the cause, and
sets appropriate flags in watchdog & recover_adapter routines.
This flag should be used to determine if bootstrap is invoked
from probe or reset context, reducing the rom-lock footprint of
the drivers.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
minidump data collection fails as driver reports data mismatch
Fix:
When the driver encounters a new entry type that it cannot process,
it should just skip the entry and adjust the total buffer size by
subtracting the skipped bytes from it. This is to ensure that there
is no data mismatch because of the new entries.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
While booting with kdump kernel, driver receive IOCB interrupts
for which it is not ready which results in processing them
before init_firmware during driver probe
Fix:
Two steps solution
1. Make driver ready to process the interrupt before interupts
handlers is registered.
2. Stop driver processing iocb interrupts if not generated as per
firmware protocol i.e R2H bit set
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If waiting for signals was interrupted then the device was put to
FAILED state. Use msleep instead of msleep_interruptible to handle
this correctly.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1
while taking minidump, to check for graceful reset.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
For ISP8xxx, adapter initialization is not retried if
qla4xxx_initialize_adapter fails.
Fix:
If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not
attached in order to skip retrial, then free the IRQs and then retry
initializing the adapter.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Return error from function qla4_8xxx_collect_md_data()
if minidump data collection fails.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add pex-dma support for ISP8324 and ISP8042 to improve
the minidump capture time.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch set is mostly driver updates (qla4, qla2 [ISF support updates],
lpfc, aacraid [dual firmware image support]) and a few bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRgAd8AAoJEDeqqVYsXL0Mg5wH/3P4wlXaRyqvyrFk1WSkmklZ
6YxzIKn/RLFmJlJvkaTT7N02ble2UqTluB6+5+AorU/jqz6DArxHsPnyv0/+2pXS
zYmp1hrcLn9dB3sZ2Y32jU2GlzHq+LSJSjjnUrA/uRrq1KTP09KCJtGbZUkvy710
x1/3e3I8u2bvBAehUkKvazg5+xlw/XImJ+IVXgUWOyiv1mNbqNEtT5qYt7sjnhLu
Mg2VfKTSb+kzxSpol3v51vh/wqY6unVcI/a9HxanihkDtkqRBRhg8wXpNAYI2xNK
uNLGq0VFpyCYfBZX0aqh01QZ++EUU2TNlRreVg4/crQnBR88EI3KtUsA1BOthwQ=
=x6dL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James "Jej B" Bottomley:
"The patch set is mostly driver updates (qla4, qla2 [ISF support
updates], lpfc, aacraid [dual firmware image support]) and a few bug
fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] iscsi_tcp: support PF_MEMALLOC/__GFP_MEMALLOC
[SCSI] libiscsi: avoid unnecessary multiple NULL assignments
[SCSI] qla4xxx: Update driver version to 5.03.00-k8
[SCSI] qla4xxx: Added print statements to display AENs
[SCSI] qla4xxx: Use correct value for max flash node entries
[SCSI] qla4xxx: Restrict logout from boot target session using session id
[SCSI] qla4xxx: Use correct flash ddb offset for ISP40XX
[SCSI] isci: add CONFIG_PM_SLEEP to suspend/resume functions
[SCSI] scsi_dh_alua: Add module parameter to allow failover to non preferred path without STPG
[SCSI] qla2xxx: Update the driver version to 8.05.00.03-k.
[SCSI] qla2xxx: Obtain loopback iteration count from bsg request.
[SCSI] qla2xxx: Add clarifying printk to thermal access fail cases.
[SCSI] qla2xxx: Remove duplicated include form qla_isr.c
[SCSI] qla2xxx: Enhancements to support ISPFx00.
[SCSI] qla4xxx: Update driver version to 5.03.00-k7
[SCSI] qla4xxx: Replace dev type macros with generic portal type macros
[SCSI] scsi_transport_iscsi: Declare portal type string macros for generic use
[SCSI] qla4xxx: Add flash node mgmt support
[SCSI] libiscsi: export function iscsi_switch_str_param
[SCSI] scsi_transport_iscsi: Add flash node mgmt support
...
This patch allows iscsiadm to manage iSCSI target information stored on
qla4xxx adapter flash on per host basis.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
If flash read for FLT fails, we are assigning wrong default
address for CHAP table in FLT, which will cause CHAP table
read/write to wrong address.
Fix:
Assign correct default CHAP table address to FLT.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.
Solution:
Re-register the interrupt handler when adapter initialization is retried.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Mailbox command timed out after switching from polling mode to interrupt mode.
Events:-
1. Mailbox interrupts are disabled
2. FW generates AEN and at same time driver enables Mailbox Interrupt
3. Driver issues new mailbox to Firmware
In above case driver will not get AEN interrupts generated by FW in step #2 as
FW generated this AEN when interrupts are disabled. During the same time
driver enabled the mailbox interrupt, so driver will not poll for interrupt.
Driver will never process AENs generated in step #2 and issues new mailbox to
FW, but now FW is not able to post mailbox completion as AENs generated before
are not processed by driver.
Fix:
Enable Mailbox / AEN interrupts before initializing FW in case of ISP83XX.
This will make sure we process all Mailbox and AENs in interrupt mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Camram is reset by FW to default values after reboot/cold boot/pci reset.
In case of AER, PCI may need to reset so we need to set correct idc reg value
after PCIE error.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move minidump code from qla4_8xxx_device_bootstrap() to
new function qla4_8xxx_get_minidump() to make code more
modular.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Device can go to READY state from COLD and skip INITIALIZATION,
In this case driver will never set IDC version from function
qla4_8xxx_device_bootstrap().
Fix:
1. Set IDC version at start of function qla4_82xx_need_reset_handler().
2. Set IDC version only if we are 1st driver to load.
3. Added new function qla4_8xxx_update_idc_reg() to set all idc reg at one
place.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ql4_8xxx_mark_entry_skipped to qla4_8xxx_mark_entry_skipped
ql4_attr_is_visible to qla4_attr_is_visible
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix warning:-
drivers/scsi/qla4xxx/ql4_nx.c:1867:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘uint32_t’ [-Wformat]
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
This provides unified readq()/writeq() helper functions for 32-bit
drivers.
For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.
- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address
- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order
This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0aff ("x86:
remove 32-bit versions of readq()/writeq()")
The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:
#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */
But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access
This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ROM lock acquiring timeout failure, driver spews lot of warning
messages in a for loop, remove the unwanted warning message to reduce
kernel messages clutter.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This code initially added for FW debugging, we don't need this
code now so taking it out.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This ensures the transition of dev_state from COLD to
INITIALIZING is within lock and atomic.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix issue where CPU lockup is seen when ql4xdontresethba is set and
driver is "stuck" in NEED_RESET state handler.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.
In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.
With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.
JIRA Key: UPSISCSI-146
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
