[why]
dcn301_calculate_wm_and_dl() causes flickering when external monitor is
connected.
This issue has been fixed before by commit 0e4c0ae59d
("drm/amdgpu/display: drop dcn301_calculate_wm_and_dl for now"), however
part of the fix was gone after commit 2cbcb78c9e ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next").
[how]
Use dcn30_calculate_wm_and_dlg() instead as in the original fix.
Fixes: 2cbcb78c9e ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With kernel module parameter "freesync_video" is enabled, if the mode
is changed to preferred mode(the mode with highest rate), then Freesync
fails because the preferred mode is treated as one of freesync video
mode, and then be configurated as freesync video mode(fixed refresh
rate).
[How]
Skip freesync fixed rate configurating when modeset to preferred mode.
Signed-off-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
DMUB firmware info is printed before it gets initialized.
Correct this order to ensure true value is conveyed.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On S4 resume we also need to fix detection of when to reload DMCUB
firmware because we're currently using the VBIOS version which isn't
compatible with the driver version.
[How] Update the hardware init check for DCN31 since it's the ASIC that
has this issue.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jude Shih <jude.shih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Hardware team suggested to use SRExitTime= 35.5us as w/a to prevent
underflow in certain modes.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
In DCN2x, HW doesn't automatically divide MASTER_UPDATE_LOCK_DB_X
by the number of pipes ODM Combined.
How:
Set MASTER_UPDATE_LOCK_DB_X to the value that is adjusted by the
number of pipes ODM Combined.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For DCN31 onward, LTTPR is to be enabled and set to Transparent by
VBIOS. Driver is to assume that VBIOS has done this without needing to
check the VBIOS interop bit.
[HOW]
Add LTTPR enable and interop VBIOS bits into dc->caps, and force-set the
interop bit to true for DCN31+.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We've gotten a number of reports about backlight control not
working on panels which indicate that they use aux backlight
control. A recent patch:
commit 2d73eabe29
Author: Camille Cho <Camille.Cho@amd.com>
Date: Thu Jul 8 18:28:37 2021 +0800
drm/amd/display: Only set default brightness for OLED
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes some other code to only use aux for backlight control on
OLED panels. The commit message seems to indicate that PWM should
be used for SDR mode on HDR panels. Do something similar for
backlight control in general. This may need to be revisited if and
when HDR started to get used.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1438
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213715
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't check DENTIST_DISPCLK_CHG_DONE to ensure dentist
display clockis updated to target value. In some scenarios with large
display clock margin, it will deliver unfinished display clock and cause
issues like display black screen.
[How]
Checking DENTIST_DISPCLK_CHG_DONE to ensure display clock
has been update to target value before driver do other clock related
actions.
Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
IP parameter min_meta_chunk_size_bytes is read for bandwidth
calculations but it was never defined.
[how]
Define min_meta_chunk_size_bytes and initialize value to 256.
Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DST_Y_PREFETCH can overflow when DestinationLinesForPrefetch values are
too large due to the former being limited to 8 bits.
[how]
Set the maximum value of DestinationLinesForPrefetch to be 255 * refclk
period.
Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Regression found in some embedded panels traces back to the earliest
upstreamed ASSR patch. The changed code flow are causing problems
with some panels.
[How]
- Change ASSR enabling code while preserving original code flow
as much as possible
- Simplify the code on guarding with internal display flag
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213779
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1620
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.
[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.
[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.
Put in a hardcoded default until we have the interface in place.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.
[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.
[how]
Correct "<" to "<="
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Yongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 72a7cf0aec ("drm/amd/display: Keep linebuffer pixel depth at
30bpp for DCE-11.0.") doesn't seems to have fixed 10bit 4K rendering over
DisplayPort for CIK GPUs. On my machine with a HAWAII GPU I get a broken
image that looks like it has an effective resolution of 1920x1080 but
scaled up in an irregular way. Reverting the commit or applying this
patch fixes the problem on v5.14-rc1.
Fixes: 72a7cf0aec ("drm/amd/display: Keep linebuffer pixel depth at 30bpp for DCE-11.0.")
Acked-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original logic is to update eDP's backlight level
on every amdgpu dm atomic commit, which causes excessive
DMUB write. As a result, when playing game or moving window
around, DMUB timeout and system lagging are observed.
[How]
We only need to update eDP's backlight level when current level
doesn't match requested level.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 2b7605d73b
Some displays are not lighting up when put in LTTPR Transparent Mode
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
We're only treating TMDS as a valid target for infoframe updates which
results in PSR being unable to transition from state 4 to state 5.
[How]
Also allow infoframe updates for DCN3.1 - following how we handle
this path for earlier ASIC as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing support for DCN2.1 DMUB diagnostic logging to
DCN3.1 so we can collect useful information if the DMUB hangs.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting CONFIG_FRAME_WARN=0 should disable 'stack frame larger than'
warnings. This is useful for example in KASAN builds. Make the dml
Makefile respect this config.
Fixes the following build warnings with CONFIG_KASAN=y and
CONFIG_FRAME_WARN=0:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn30/display_mode_vba_30.c:3642:6:
warning: stack frame size of 2216 bytes in function
'dml30_ModeSupportAndSystemConfigurationFull' [-Wframe-larger-than=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn31/display_mode_vba_31.c:3957:6:
warning: stack frame size of 2568 bytes in function
'dml31_ModeSupportAndSystemConfigurationFull' [-Wframe-larger-than=]
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Reka Norman <rekanorman@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also copy over the part that makes old gcc handling cross-platform.
Fixes: df7a1658f2 ("drm/amdgpu/dc: fix DCN3.1 Makefile for PPC64")
Fixes: 926d6972ef ("drm/amd/display: Add DCN3.1 blocks to the DC Makefile")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During GPU reset, when receiving a DMCUB OUTBUX0 interrupt,
DAL code will set it to be OUTBOX interrupt and sets hw interrupt.
However, OUTBOX interrupt is not registered yet, so a NULL pointer
access will be executed.
Call Trace:
dal_irq_service_set+0x30/0x90 [amdgpu]
dc_interrupt_set+0x24/0x30 [amdgpu]
amdgpu_dm_set_dmub_outbox_irq_state+0x22/0x30 [amdgpu]
amdgpu_irq_update+0x77/0xa0 [amdgpu]
amdgpu_irq_gpu_reset_resume_helper+0x67/0xa0 [amdgpu]
amdgpu_do_asic_reset+0x219/0x260 [amdgpu]
amdgpu_device_gpu_recover.cold+0x8c5/0xb64 [amdgpu]
amdgpu_debugfs_gpu_recover_show+0x2c/0x60 [amdgpu]
seq_read_iter+0xc2/0x450
? do_anonymous_page+0x22c/0x3b0
seq_read+0xf9/0x140
full_proxy_read+0x5c/0x90
vfs_read+0xaa/0x190
ksys_read+0x67/0xe0
__x64_sys_read+0x1a/0x20
Fixes: effbf6ca7e ("drm/amdgpu/display: remove an old DCN3 guard")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-and-tested-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
valid DAL irq should be < DAL_IRQ_SOURCES_NUMBER.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-and-tested-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 33f409e60e.
The patch that we are reverting here was originally applied because it
fixes multiple IGT issues and flickering in Android. However, after a
discussion with Sean Paul and Mark, it looks like that this patch might
cause problems on ChromeOS. For this reason, we decided to revert this
patch.
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Mark Yacoub <markyacoub@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Sometimes, DP receiver chip power-controlled externally by an
Embedded Controller could be treated and used as eDP,
if it drives mobile display. In this case,
we shouldn't be doing power-sequencing, hence we can skip
waiting for T7-ready and T9-ready."
[How]
Added a feature mask to enable eDP no power sequencing feature.
To enable this, set 0x10 flag in amdgpu.dcfeaturemask on
Linux command line.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Introduce CMD for EDID CEA block parsing
- Add SCR5 definition for reporting eDP power sequencer status
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Increase width of some variables to avoid comparing integers of
different widths
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating the file to fix the missing line
Signed-off-by: Logush Oliver <ollogush@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
recent VBIOS dce_infotable reference clock change caused a I2c regression.
instead of relying on vbios, let's get it from HW directly.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After panel power up, if PSR entry attempted too early,
PSR state may get stuck in transition.
This could happen if the panel is not ready
to respond to the SDP PSR entry message.
In this case dmub f/w is unable to abort PSR entry
since abortion is not permitted after the SDP has been sent.
[How]
Skip 5 pageflips before PSR enable.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some SOC BB paramters may vary per SKU, and it does
not make sense for driver to hardcode these values.
This change was added for dcn30 and dcn301, but not
for dcn302 and dcn303
[how]
Parse the values from VBIOS if available, and use
them if valid
Fixes: 93669c8e48 ("drm/amd/display: get socBB from VBIOS")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
