After the previous changes, the FIB info is embedded in every nexthop
group struct, which in turn is embedded in every FIB entry struct.
We can therefore safely remove the FIB info from the entry struct. This
has the added advantage of making the router-related structs more
generic and suitable for use with IPv6 offloads.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the only FIB entries that were associated with a nexthop
group were routes to remote networks where all the nexthop devices had a
valid router interface (RIF). This is in contrast to the FIB code,
where all the routes are associated with a FIB info. The same design
choice needs to be applied to the driver's cache.
Based on the NH_{ADD,DEL} events which will be added later in the
patchset, we need to be able to change the action (forward / trap)
associated with all the routes using the nexthop group. However, if we
can't link between the nexthop and the routes using it, then the above
is impossible.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch is going to generalize the way in which we store routes.
Instead of attaching a nexthop group only to gatewayed routes, one will
be attached to each route, in a similar way to the way the FIB code
stores its routes.
The above means that any function operating on a nexthop group cannot
assume the group represents only gatewayed nexthops. One such function
is the one that refreshes a nexthop group and updates the adjacency
table following nexthop changes.
For a nexthop group that doesn't represent any gateways this function
would essentially be a NOP, but it would be useful if it did update the
action associated with any route using it. This will allow us to later
consolidate code paths when a nexthop changes following NH_{ADD,DEL}
events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the scope of the FIB info to distinguish between a
direct unicast route and a gatewayed one. However, the kernel is
perfectly happy to configure a route with scope UNIVERSE to a directly
connected network.
Instead, we can rely on the first nexthop's scope to check if the route
is gatewayed or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later in the patchset we'll add the NH_{ADD,DEL} events which will let
us know when a nexthop is considered to be dead. Based on these events
we need to be able to add or remove the nexthop from the device's
tables.
Therefore, store the private nexthop structs in a hash table and use the
kernel's fib_nh struct as the key, so that we'll be able to easily find
them when the events are received.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we're notified about a new RTN_UNICAST route we perform
a lookup on the nexthop group list looking for a group with a matching
configuration to that found in the FIB info. This is quite inefficient.
Instead, we can simply rely on the kernel to consolidate several FIB
configurations into the same FIB info and use the FIB info as the key
for our private nexthop group struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we invalidate a nexthop we should also invalidate its neighbour
entry pointer as it might be destroyed later on. This makes the nexthop
de-init function symmetric with its init and also ensures nobody will
try to access the neighbour entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No rollback is needed since the chain is in consistent state and
mlxsw_afa_block_destroy() will take care of putting it away. So remove
the one we have now which is wrong. Also move the set of 'finished' flag
to the beginning of the function, because the block is certainly unusable
for future action addition no matter if the function succeeds or not.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch complains about two unsigned without type after.
Since the value return is u32, it is simpler to replace it by u32 instead
of "unsigned int"
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64 x variable in sysfs_display_ring is unused.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cf32deec16 ("stmmac: add tx_skbuff_dma to save descriptors used by PTP"),
the struct dma_desc *p in stmmac_tx_clean was not used at all.
This patch remove this dead code.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY is found, printing which one was found (and which type/model) is
a good information to know.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool stat counter rx_crc from stmmac is mis-named, the name
seems to speak about the number of RX CRC done, but in fact it is about
errors.
This patch rename it to rx_crc_errors, just like the same ifconfig
counter.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewrite two test against NULL value with correct style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message about invalid speed does not state 1000 as a valid speed.
It is much simpler to said that the speed is invalid.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by checkpatch ENOSYS means 'invalid syscall nr' and nothing
else.
This patch replace ENOSYS by the more appropriate value EINVAL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac_dma_reset function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_mdio_busy_wait() function do the same job than
readl_poll_timeout().
So is is better to replace it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch complains about some code style problem on stmmac_mdio.c.
This patch fix them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about asm/io.h.
Sorting all includes in the process.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about free software address.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some typos in comments.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the define MAC_RNABLE_RX have a typo, rename it to MAC_ENABLE_RX
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix 802.11w, which was failing to due an IGTK bug;
* A few more bugzilla bug fixes;
* A channel-switch race condition fix;
* Some fixes related to suspend/resume with new HW;
* The RF-kill saga continues;
* And some other fixes here and there...
-----BEGIN PGP SIGNATURE-----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=dHzs
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Some patches focusing on bugfixes for v4.11:
* Fix 802.11w, which was failing to due an IGTK bug;
* A few more bugzilla bug fixes;
* A channel-switch race condition fix;
* Some fixes related to suspend/resume with new HW;
* The RF-kill saga continues;
* And some other fixes here and there...
The stack must not pass packets to device drivers that are shorter
than the minimum link layer header length.
Previously, packet sockets would drop packets smaller than or equal
to dev->hard_header_len, but this has false positives. Zero length
payload is used over Ethernet. Other link layer protocols support
variable length headers. Support for validation of these protocols
removed the min length check for all protocols.
Introduce an explicit dev->min_header_len parameter and drop all
packets below this value. Initially, set it to non-zero only for
Ethernet and loopback. Other protocols can follow in a patch to
net-next.
Fixes: 9ed988cd59 ("packet: validate variable length ll headers")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qualcomm/emac/emac-ethtool.c:155:49-50: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED Mode:
Microsemi PHY support 2 LEDs (LED[0] and LED[1]) to display different
status information that can be selected by setting LED mode.
LED Mode parameter (vsc8531, led-0-mode) and (vsc8531, led-1-mode) get
from Device Tree.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't affect how the code works.
My static checker complains that the mask and shift doesn't make sense
because 0xffffff << 16 goes beyond the end of 32 bits. It should be
0xffff instead but the existing code won't cause runtime bugs.
Also the casting here is not needed and not consistent with the rest of
the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divide a mfuart related print so it won't exceed the allowed
MAX_MSG_LEN (110 bytes) per print.
Fixes: 19f63c531b ("iwlwifi: mvm: support v2 of mfuart load notification")
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing an IGTK, iwl_mvm_send_sta_igtk() was
called before station ID was retrieved, so the function
was invoked with an invalid station ID. Fix this by first
getting the station ID.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192411
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The race happens when we send ADD_STA(auth->assoc) -> LQ_CMD
between the commands the FW sometimes loses the medium for AUX, and
sends a ndp to the AP and the flow becomes, ADD_STA -> send ndp -> LQ_CMD
the problem is that there's no rates yet defined for sending the ndp and
FW generates an assert.
The fix: change the order of the commands to LQ_CMD -> ADD_STA
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The session protection set for association is only removed when
BSS_CHANGED_BEACON_INFO is set and BSS_CHANGED_ASSOC is not set.
However, mac80211 may set both on association (in case a beacon was
already received). In this case, mac80211 will not set
BSS_CHANGED_BEACON_INFO on the next beacons because it has already
notified the beacon change, so the session protection is never removed
(until the session protection ends).
When a CSA is received within this time, the station will fail to
folllow the channel switch because it cannot schedule the time event.
Fix this by removing the session protection when
BSS_CHANGED_BEACON_INFO and BSS_CHANGED_ASSOC are both set.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, when getting a RFKILL interrupt, the transport enters a flow
in which it stops the device, disables other interrupts, etc. After
stopping the device, the transport resets the hw, and sleeps. During
the sleep, a context switch occurs and host commands are sent by upper
layers (e.g. mvm) to the fw. This is possible since the op_mode layer
and the transport layer hold different mutexes.
Since the STATUS_RFKILL bit isn't set, the transport layer doesn't
recognize that RFKILL was toggled on, and no commands can actually be
sent, so it enqueues the command to the tx queue and sets a timer on
the queue.
After switching context back to stopping the device, STATUS_RFKILL is
set, and then the transport can't send the command to the fw.
This eventually results in a queue hang.
Fix this by setting STATUS_RFKILL immediately when
the interrupt is fired.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c in iwldvm.
Fix the same bug in iwlmvm.
This because
i = index - 1;
for (mask = (1 << i); i >= 0; i--, mask >>= 1)
is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c.
Undefined behaviour in drivers/net/wireless/intel/iwlwifi/dvm/rs.c:746:18
This because
i = index - 1;
for (mask = (1 << i); i >= 0; i--, mask >>= 1)
is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enabling the RTPM Kconfig option can be fairly risky.
Runtime PM must be validated against a specific platform
before it can be safely enabled. Hence, it makes no sense
for distros and other big OS vendors to enable it since
they ship code to various systems and unknown platform.
Make sure that this is hinted properly by making the
IWLWIFI_PCIE_RTPM Kconfig option depend on EXPERT.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=172411
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
David reported that the code I added uses the decrement
and increment operator on a boolean variable.
Fix that.
Fixes: 0cd58eaab1 ("iwlwifi: pcie: allow the op_mode to block the tx queues")
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
queue_entry field of skbdesc is not read any more, remove it to allow
skbdesc contain other data.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We might kill TX or RX urb during rt2x00usb_flush_entry(), what can
cause anchor list corruption like shown below:
[ 2074.035633] WARNING: CPU: 2 PID: 14480 at lib/list_debug.c:33 __list_add+0xac/0xc0
[ 2074.035634] list_add corruption. prev->next should be next (ffff88020f362c28), but was dead000000000100. (prev=ffff8801d161bb70).
<snip>
[ 2074.035670] Call Trace:
[ 2074.035672] [<ffffffff813bde47>] dump_stack+0x63/0x8c
[ 2074.035674] [<ffffffff810a2231>] __warn+0xd1/0xf0
[ 2074.035676] [<ffffffff810a22af>] warn_slowpath_fmt+0x5f/0x80
[ 2074.035678] [<ffffffffa073855d>] ? rt2x00usb_register_write_lock+0x3d/0x60 [rt2800usb]
[ 2074.035679] [<ffffffff813dbe4c>] __list_add+0xac/0xc0
[ 2074.035681] [<ffffffff81591c6c>] usb_anchor_urb+0x4c/0xa0
[ 2074.035683] [<ffffffffa07322af>] rt2x00usb_kick_rx_entry+0xaf/0x100 [rt2x00usb]
[ 2074.035684] [<ffffffffa0732322>] rt2x00usb_clear_entry+0x22/0x30 [rt2x00usb]
To fix do not anchor TX and RX urb's, it is not needed as during
shutdown we kill those urbs in rt2x00usb_free_entries().
Cc: Vishal Thanki <vishalthanki@gmail.com>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 6773386f97 ("rtlwifi: rtl8192c-common: Fix "BUG: KASAN:"),
a BUG detected when CONFIG_KASAN=y was fixed by reordering the layouts
of struct rtl_pci_priv, and struct rtl_usb_priv so that the variables
used by both PCI and USB drivers have the same offsets in both structs.
The better fix of relocating the critical variables into struct rtl_priv
was deferred as these changes do not have to be applied to stable
kernels.
This change also removes CamelCase variables with pLed0 => pled0.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now we always have __brcmf_err function we can do perfectly fine with
just one macro.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will allow extending code and using more detailed messages e.g.
with the help of dev_err.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows simplifying the code by adding a simple IS_ENABLED check for
CONFIG_BRCMDB symbol.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is necessary so that - if ath10k is the only driver using
dev_coredump*() - the functionality is built into the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This now declares a module parameter, so include the necessary
header file for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove redundant semicolon after switch statement.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.
Fixes: 0690405fef ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:
1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
if we actually have aggregation open on the queue. This causes
mac80211 to send a BAR frame even though there is no aggregation
open.
Fix that by simply checking the AMPDU flag that is set on by
mac80211 for AMPDU packets.
2. When reclaiming frames in aggregation mode, we reclaim based on
scheduler ssn and not the SN.
The reason is that scheduler ssn may be ahead of SN due to a hole
in the BA window that was filled.
However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
the reclaim flow will still go to the code of non-aggregation
instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
aggregation queue.
Fix that by always using the aggregation reclaim code by default in
DQA mode (currently it is implicitly used by default for all queues
except the reserved BSS queue).
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Handling of the number of space time streams was missing for HT rate in
rate printing function. Fix it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting RF_KILL and disabling radio, the device gets stopped
and reset. This erases the IVAR table that matches the interrupt
to its cause, and is essential for MSIX proper functionality.
Till now, the table wasn't re-configured after the reset, and
therefore the interrupt that enabled radio didn't fire on the
right irq, and the driver didn't handle it correctly.
To fix this, configure the IVAR table again after resetting the
device.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During the suspend/resume flow some HW blocks are reset. This causes
the IVAR table to be completely erased. This table is where interrupt
causes are bound to specific IRQs. When the table is empty the
interrupt handlers are not called correctly. Fix this by reconfiguring
the IVAR table after resume.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MSIX configuration flow includes two different stages:
configuring the HW by writing to the IVAR table and configuring the SW
to reflect the HW configuration.
The HW configuration is needed on each HW reset,
whereas the SW configuration is only needed during the init flow.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
msix configuration functions should be called by other functions.
For example by pcie_d3_resume, move it above to enable it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch errors by not dereferencing iq pointer if it's NULL.
See http://marc.info/?l=kernel-janitors&m=148637299004834&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Load correct firmware in rtl8192ce wireless driver, from Jurij
Smakov.
2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver,
from Martin KaFai Lau.
3) Need to reference count PHY driver module when it is attached, from
Mao Wenan.
4) Don't do zero length vzalloc() in ethtool register dump, from
Stanislaw Gruszka.
5) Defer net_disable_timestamp() to a workqueue to get out of locking
issues, from Eric Dumazet.
6) We cannot drop the SKB dst when IP options refer to them, fix also
from Eric Dumazet.
7) Incorrect packet header offset calculations in ip6_gre, again from
Eric Dumazet.
8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too.
9) tcp_splice_read() can get into an infinite loop with URG, and hey
it's from Eric once more.
10) vnet_hdr_sz can change asynchronously, so read it once during
decision making in macvtap and tun, from Willem de Bruijn.
11) Can't use kernel stack for DMA transfers in USB networking drivers,
from Ben Hutchings.
12) Handle csum errors properly in UDP by calling the proper destructor,
from Eric Dumazet.
13) For non-deterministic softirq run when scheduling NAPI from a
workqueue in mlx4, from Benjamin Poirier.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
sctp: check af before verify address in sctp_addr_id2transport
sctp: avoid BUG_ON on sctp_wait_for_sndbuf
mlx4: Invoke softirqs after napi_reschedule
udp: properly cope with csum errors
catc: Use heap buffer for memory size test
catc: Combine failure cleanup code in catc_probe()
rtl8150: Use heap buffers for all register access
pegasus: Use heap buffers for all register access
macvtap: read vnet_hdr_size once
tun: read vnet_hdr_sz once
tcp: avoid infinite loop in tcp_splice_read()
hns: avoid stack overflow with CONFIG_KASAN
ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches
ipv6: tcp: add a missing tcp_v6_restore_cb()
nl80211: Fix mesh HT operation check
mac80211: Fix adding of mesh vendor IEs
mac80211: Allocate a sync skcipher explicitly for FILS AEAD
mac80211: Fix FILS AEAD protection in Association Request frame
ip6_gre: fix ip6gre_err() invalid reads
netlabel: out of bound access in cipso_v4_validate()
...
This bug is harmless because it's just a sanity check and we always
pass valid values for "encap_type" but the test is off by one.
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the lane swapping (called
"port mirroring" in PHY's CFG4 register) feature of the DP83867 TI's PHY
device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as off
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Since we don't have anything special, switch to the generic
phy_ethtool_get_link_ksettings() function now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYmQKaAAoJEEg/ir3gV/o+RBMH/RGHNw3yPB2MyWo28V3eabw+
xl/SymiNOUgmq03ULYoc6xJpi9RCya7m/Kyce1M/M1gSz6LXubG2IDw9QsKV8lnc
+5rwHCKjop6MdR3khsgqvWqGiKfQN0+QON5MjlPZB3/4u8qFcjauhfXpiX9naMO5
aB/Sm9zRPwRnsEhy2AwPyZqOxe5boZzHqmZxpthIgPMtqbpBYNkTkooljsj/KqXf
AO3y/mdGykELPF3lIHTE4X9zixx5s6MrlAYX2uGUrAojs2WVIBsq3iXI/J8X9zs/
lg7to15WoMttR66vRZ120U6tx17OMmoxuAp+bmgZumabi/wDAZGSy5ELbH28WlY=
=F+t/
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-01-31
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice, it's supposed to be
done in netdev_start_xmit() and anyway is re-written. Also, no reason to
update trans time in case of an error.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dedicated transmit function and transmit completion handler for
XDP. The XDP transmit logic and completion logic are different than
regular TX ring. The TX buffer is recycled back to the RX ring when
it completes.
v3: Improved the buffer recyling scheme for XDP_TX.
v2: Add trace_xdp_exception().
Add dma_sync.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.
v3: Pass modified offset and length to stack for XDP_PASS.
Remove Kconfig option.
v2: Added trace_xdp_exception()
Added dma_syncs.
Added XDP headroom support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_TX requires a different function to handle completion. Add a
function pointer to handle tx completion logic. Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic for an extra set of TX rings for XDP. If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set. A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings. Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring. To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping. The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.
v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings. Add a new
function bnxt_reserve_rings() to centralize the logic. This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.
Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we have separate rx_event and agg_event parameters
to keep track of rx and aggregation events. Combine these events into
an u8 event mask with different bits defined for different events. This
way, it is easier to expand the logic to include XDP tx events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mode is to support XDP. In this mode, each rx ring is configured
with page sized buffers for linear placement of each packet. MTU will be
restricted to what the page sized buffers can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the global constants BNXT_RX_OFFSET and BNXT_RX_DMA_OFFSET to
device parameters. This will make it easier to support XDP with
headroom support which requires different RX buffer offsets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is running in XDP mode, rx buffers are DMA mapped as
DMA_BIDIRECTIONAL. Add a field so the code will map/unmap rx buffers
according to this field.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need the RX buffer's DMA address to transmit the
packet. Convert the DMA address field to a permanent field in
bnxt_sw_rx_bd.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor refactoring of bnxt_rx_skb() so that it can easily be replaced by
a new function that handles packets in a single page. Also, use a
function pointer bp->rx_skb_func() to switch to a new function when
we add the new mode in the next patch.
Add a new field data_ptr that points to the packet data in the
bnxt_sw_rx_bd structure. The original data field is changed to void
pointer so that it can either hold the kmalloc'ed data or a page
pointer.
The last parameter of bnxt_rx_skb() which was the length parameter is
changed to include the payload offset of the packet in the upper 16 bit.
The offset is needed to support the rx page mode and is not used in
this existing function.
v3: Added a new data_ptr parameter to bp->rx_skb_func(). The caller
has the option to modify the starting address of the packet. This
will be needed when XDP with headroom support is added.
v2: Changed the name of the last parameter to offset_and_len to make the
code more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support setting the pause parameters, the driver can no longer just
mirror the PHY. The set_pauseparam feature allows the driver to
force the setting in the MAC, regardless of how the PHY is configured.
This means that we now need to maintain an internal state for pause
frame support, and so get_pauseparam also needs to be updated.
If the interface is already running when the setting is changed, then
the interface is reset.
Note that if the MAC is configured to enable RX pause frame support
(i.e. it transmits pause frames to throttle the other end), but the
PHY is configured to block those frames, then the feature will not work.
Also some buffer size initialization code into emac_init_adapter(),
so that it lives with similar code, including the initializtion of
pause frame support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame and the following message may be logged:
NOHZ: local_softirq_pending 08
The problem is the same as what was described in commit ec13ee8014
("virtio_net: invoke softirqs after __napi_schedule") and this patch
applies the same fix to mlx4.
Fixes: 07841f9d94 ("net/mlx4_en: Schedule napi when RX buffers allocation fails")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PSAMPLE is a loadable module, spectrum must not be built-in:
drivers/net/built-in.o: In function `mlxsw_sp_rx_listener_sample_func':
spectrum.c:(.text+0xe357e): undefined reference to `psample_sample_packet'
This adds a Kconfig dependency to enforce usable configurations.
Fixes: 98d0f7b9ac ("mlxsw: spectrum: Add packet sample offloading support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 MDIO bus controllers can support for clause 45 accesses.
The internal SERDES interfaces need this, and it is likely external
10GHz PHYs will be clause 45.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().
Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().
The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.
When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.
When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.
At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
References: https://bugs.debian.org/852556
Reported-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Tested-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for XDP adjust head by allocating a 256B header region
that XDP programs can grow into. This is only enabled when a XDP
program is loaded.
In order to ensure that we do not have to unwind queue headroom push
queue setup below bpf_prog_add. It reads better to do a prog ref
unwind vs another queue setup call.
At the moment this code must do a full reset to ensure old buffers
without headroom on program add or with headroom on program removal
are not used incorrectly in the datapath. Ideally we would only
have to disable/enable the RX queues being updated but there is no
API to do this at the moment in virtio so use the big hammer. In
practice it is likely not that big of a problem as this will only
happen when XDP is enabled/disabled changing programs does not
require the reset. There is some risk that the driver may either
have an allocation failure or for some reason fail to correctly
negotiate with the underlying backend in this case the driver will
be left uninitialized. I have not seen this ever happen on my test
systems and for what its worth this same failure case can occur
from probe and other contexts in virtio framework.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP we will need to reset the queues to allow for buffer headroom
to be configured. In order to do this we need to essentially run the
freeze()/restore() code path. Unfortunately the locking requirements
between the freeze/restore and reset paths are different however so
we can not simply reuse the code.
This patch refactors the code path and adds a reset helper routine.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out qp assignment.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the do_xdp_prog is mostly if/else branches handling
the different modes of virtio_net. So remove it and handle running
the program in the per mode handlers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP use case and to allow ethtool reset tests it is useful to be
able to use reset paths from contexts where rtnl lock is already
held.
This requries updating virtnet_set_queues and free_receive_bufs the
two places where rtnl_lock is taken in virtio_net. To do this we
use the following pattern,
_foo(...) { do stuff }
foo(...) { rtnl_lock(); _foo(...); rtnl_unlock()};
this allows us to use freeze()/restore() flow from both contexts.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In an RFC patch, Sven Eckelmann and Simon Wunderlich reported:
"QCA 802.11n chips (especially AR9330/AR9340) sometimes end up in a
state in which a read of AR_CFG always returns 0xdeadbeef.
This should not happen when when the power_mode of the device is
ATH9K_PM_AWAKE."
Include the check for the default register state in the existing MAC
hang check.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also include common MAC alive check. This should make the hang checks
more reliable for modes where beacons are not sent and is used as a
starting point for further hang check improvements
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the even that the wcn36xx interface is brought down while a hw_scan
is active we must abort and wait for the ongoing scan to signal
completion to mac80211.
Reported-by: Mart Raudsepp <leio@gentoo.org>
Fixes: 886039036c ("wcn36xx: Implement firmware assisted scan")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernels built with CONFIG_KASAN=y report the following BUG for rtl8192cu
and rtl8192c-common:
==================================================================
BUG: KASAN: slab-out-of-bounds in rtl92c_dm_bt_coexist+0x858/0x1e40
[rtl8192c_common] at addr ffff8801c90edb08
Read of size 1 by task kworker/0:1/38
page:ffffea0007243800 count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x8000000000004000(head)
page dumped because: kasan: bad access detected
CPU: 0 PID: 38 Comm: kworker/0:1 Not tainted 4.9.7-gentoo #3
Hardware name: Gigabyte Technology Co., Ltd. To be filled by
O.E.M./Z77-DS3H, BIOS F11a 11/13/2013
Workqueue: rtl92c_usb rtl_watchdog_wq_callback [rtlwifi]
0000000000000000 ffffffff829eea33 ffff8801d7f0fa30 ffff8801c90edb08
ffffffff824c0f09 ffff8801d4abee80 0000000000000004 0000000000000297
ffffffffc070b57c ffff8801c7aa7c48 ffff880100000004 ffffffff000003e8
Call Trace:
[<ffffffff829eea33>] ? dump_stack+0x5c/0x79
[<ffffffff824c0f09>] ? kasan_report_error+0x4b9/0x4e0
[<ffffffffc070b57c>] ? _usb_read_sync+0x15c/0x280 [rtl_usb]
[<ffffffff824c0f75>] ? __asan_report_load1_noabort+0x45/0x50
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d0cbe>] ? rtl92c_dm_rf_saving+0x96e/0x1330 [rtl8192c_common]
...
The problem is due to rtl8192ce and rtl8192cu sharing routines, and having
different layouts of struct rtl_pci_priv, which is used by rtl8192ce, and
struct rtl_usb_priv, which is used by rtl8192cu. The problem was resolved
by placing the struct bt_coexist_info at the head of each of those private
areas.
Reported-and-tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtcoutsrc.c to use the
standard routines. It also deletes the definitions of the now-unused
debugging macros, and turns on compilation of all the routines in
btcoexist.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8192e2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In several places, "BANDWITH" is used when "BANDWIDTH" should have been
used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d8 ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Felix:
Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.
Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.
Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new helper reads extra frequency limits specified in DT and
disables unavailable chanels. This is useful for devices (like home
routers) with chipsets limited e.g. by board design.
In order to respect info read from DT we simply need to check for
IEEE80211_CHAN_DISABLED bit when constructing channel info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver doesn't use mac80211, so it shouldn't include mac80211.h,
include only the necessary cfg80211.h instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
-----BEGIN PGP SIGNATURE-----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=DFHh
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of improvements and fixes for v4.11.
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
btcoex needs to sleep, thus it must run in thread context.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ant_sel is set, we need to fill single_ant_path to select correct
antenna path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine rtl_get_hwpg_bt_type() is better in halbtcoutsrc.c than in
rtl_btc.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new code handles the package-type of the chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbtcoutsrc.c is a better place for routine rtl_get_hwpg_ant_num()
than file rtl_btc.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices with RTL8732BE wifi/Bluetooth adapters are shipped with only
a single antenna. On a subset of these, the EEPROM is incorectly coded
to indicate the wrong connection. The resulting problems have been fixed
for wifi. This change handles them for BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This routine uses its own debugging macros These are changed to use the
the recently rewritten RT_TRACE macro. There are also some renamed
variables that were missed in the previous step.
The only functional change is that some debugging statements have been
dropped based on the final code supplied by Realtek.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine halbtc_get() will need to be able to get the vendor ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new value is needed for future capability.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We assign different retry limit according to vif type, because
it can boost performance in field.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential race condition when the control byte of a CAM
entry is written first. Write in reverse order to correct the condition.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Read this value once and cache locally, as it can be updated between
the test and use (TOCTOU).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit abeffce ("net/mlx5e: Fix a -Wmaybe-uninitialized warning"), I fixed a
gcc warning for the ipv4 offload handling. Now we get the same warning for the
added ipv6 support:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:815:40: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
We can apply the same workaround here as well.
Fixes: ce99f6b97f ("net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When resuming, it's possible for the following scenario to occur:
* iwl_pci_resume() enables the RF-kill interrupt
* iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
* RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
state, now 'radio disabled', and acquires the &trans_pcie->mutex.
* iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
indicate to the higher layers that the radio is now disabled (and
stops the device while at it)
* iwl_pcie_irq_handler() drops the mutex
* iwl_pci_resume() continues, acquires the mutex and calls the higher
layers to indicate that the radio is enabled.
At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant. Remove it and access
trans->cfg instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use
an indexed load for the register address, but it has an absolutely detrimental
effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely
kernel stack overflow aside from very complex object code:
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats':
hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common':
hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs':
hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs':
hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs':
hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs':
hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init':
hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs':
hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats':
hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs':
hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE
seems safe anyway and it avoids a serious issue for some people. I have verified
that with gcc-5.3.1, the object code we get is better in the new version
both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte
stack frame for hns_dsaf_get_regs() but otherwise have practically identical
object code.
With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already
good either way.
This patch is probably not urgent to get into 4.11 as only KASAN=y builds
with certain compilers are affected, but I still think it makes sense to
backport into older kernels.
Cc: stable@vger.kernel.org
Fixes: 511e6bc ("net: add Hisilicon Network Subsystem DSAF support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes: 1f8176f735 ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 364b605573 ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We periodically ask the neighbouring system to try and resolve
neighbours that are used for nexthops, but aren't currently resolved.
However, 'nud_state' is protected by the neighbour lock, so we shouldn't
access it without taking it. Instead, we can simply check the
'connected' field of the neighbour entry, which we update upon
NEIGH_UPDATE events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only add neighbour entries that are also used for nexthops to
'nexthop_neighs_list', so when iterating over this list there's no need
to check that the entry is indeed used for nexthops.
Remove the redundant check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 18bfb924f0 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 33b1341cd1 ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b3189 ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYmJChAAoJEG4XJFUm622b+GIIAJCOUqAC67Mk1/jTgyVlUHZc
4uLocdhupiozZjBTh7z1lClY3EdT38AAkstcPRXIIQLcVMjkU4B9e5nLUQFv3R/u
Bt7waNd5KixG+fX0iDPiuLj21SeMNYGtBNQ1PYSiiuuYaWXyAwplK4FW00KkUlqA
i0V2DHt1BZD3psfhPcKAmx/8kAjCjg2jX1HxMoaLHpC4HUkDdNSd87ZjrEJWN37u
eLihSdtw5+d8HMqHTmbgGXhiQKNRN9GRv7NMX+iUSSmu4oPwJtE5VLMU24VDeDwW
3rgprba5p/ddz20iBtWAVRytOHdt5GtrnWCInI2jZk3QpjmM4hqEqoOhc9E47Dc=
=0wO8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
4K Uar series modified the mlx5e driver to use the new bfreg API,
and mistakenly removed the sq->uar_map iomem data path dedicated
pointer, which was meant to be read from xmit path for cache locality
utilization.
Fix that by returning that pointer to the SQ struct.
Fixes: 7309cb4ad71e ("IB/mlx5: Support 4k UAR for libmlx5")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
ConnectX-5 and later HW generations will report min inline mode ==
MLX5_INLINE_MODE_NONE, which means driver is not required to copy packet
headers to inline fields of TX WQE.
Avoid copy to inline segment in XDP TX routine when HW inline mode doesn't
require it.
This will improve CPU utilization and boost XDP TX performance.
Tested with xdp2 single flow:
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
HCA: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 7.4Mpps
After: 7.8Mpps
Improvement: 5%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
ConnectX-5 and later HW generations will report min inline mode ==
MLX5_INLINE_MODE_NONE, which means driver is not required to copy packet
headers to inline fields of TX WQE.
When inline is not required, vlan insertion will be handled in the
TX descriptor rather than copy to inline.
For LSO case driver is still required to copy headers, for the HW to
duplicate on wire.
This will improve CPU utilization and boost TX performance.
Tested with pktgen burst single flow:
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
HCA: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 15.1Mpps
After: 17.2Mpps
Improvement: 14%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Add new TX WQE fields for Connect-X5 vlan insertion support,
type and vlan_tci, when type = MLX5_ETH_WQE_INSERT_VLAN the
HW will insert the vlan and prio fields (vlan_tci) to the packet.
Those bits and the inline header fields are mutually exclusive, and
valid only when:
MLX5_CAP_ETH(mdev, wqe_inline_mode) == MLX5_CAP_INLINE_MODE_NOT_REQUIRED
and MLX5_CAP_ETH(mdev, wqe_vlan_insert),
who will be set in ConnectX-5 and later HW generations.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
There is a hardware feature that will pad the start or end of a DMA to
be cache line aligned to avoid RMWs on the last cache line. The default
cache line size setting for this feature is 64B. This change configures
the hardware to use 128B alignment on systems with 128B cache lines.
In addition we lower bound MPWRQ stride by HCA cacheline in mlx5e,
MPWRQ stride should be at least the HCA cacheline, the current default
is 64B and in case HCA_CAP.cach_line_128byte capability is set, MPWRQ RX
stride will automatically be aligned to 128B.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAliYiW8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9jdWCACU/2SxD8WcIcP5HZgJMxv9K9LyRC++
qQb1SQKUiedAF0173IQAVawe105LEdZS08o8ovNCzcU0gLHmfAKysjXEnWVqpyLA
9zOBkl5XzjFsi9KI1TVsn/pUlk3yCq8w2azmt3mi/G5yLoAE0G46pzjbpOYyz67d
Gyoh4i9OhsQOmgpefkwtyPxlh5Xd28ohdPv8NCBb17No+1Dfs4qji1TTyVY9sqNr
8AwRl9BmTqDvZMUPRsdXk+XqZyITGLt+kMa80hd+XFmNkoWy6EKMbFiuVjkpZqtL
kX/Tfe5/mEiBegBvIUVkeOrA7MryNLOf0ZO+bLdNnSTJZJyIro1kAyIc
=kgvC
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.11-20170206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-02-06
this is a pull request of 16 patches for net-next/master.
The first two patches by David Jander and me add the rx-offload
framework for CAN devices to the kernel. The remaining 14 patches
convert the flexcan driver to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
