Fix a bug where we modified the mac_filter_hash while outside a lock,
when handling addition of broadcast filters.
Normally, we add filters to firmware by batching the additions into
lists and issuing 1 update for every few filters. Broadcast filters are
handled differently, by instead setting the broadcast promiscuous mode
flags. In order to make sure the 1<->1 mapping of filters in our
addition array lined up with filters in the hlist tmp_add_list, we had
to remove the filter and move it back to the main hash. However, we
didn't do this under lock, which could cause consistency problems for
the list.
Fix this by updating i40e_update_filter_state logic so that it knows to
avoid broadcast filters. This ensures that we don't have to remove the
filter separately, and can put it back using the normal flow.
Change-ID: Id288fade80b3e3a9a54b68cc249188cb95147518
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The intent of this message was to indicate to a user that we might have
missed a timestamp event for a valid packet. The original method of
detecting the missed events relied on waiting until all 4 registers were
filled.
A recent commit d55458c0cd7a5 ("i40e: replace PTP Rx timestamp hang
logic") replaced this logic with much better detection
scheme that could detect a stalled Rx timestamp register even when other
registers were still functional.
The new logic means that a message will be displayed almost as soon as
a timestamp for a dropped frame occurs. This new logic highlights that
the hardware will attempt timestamp for frames which it later decides to
drop. The most prominent example is when a multicast PTP frame is
received on a multicast address that we are not subscribed to.
Because the hardware initiates the Rx timestamp as soon as possible, it
will latch an RXTIME register, but then drop the packet.
This results in users being confused by the message as they are not
expecting to see dropped timestamp messages unless their application
also indicates that timestamps were missing.
Resolve this by reducing the severity and frequency of the displayed
message. We now only print the message if 3 or 4 of the RXTIME registers
are stalled and get cleared within the same watchdog event. This ensures
that the common case does not constantly display the message.
Additionally, since the message is likely not as meaningful to most
users, reduce the message to a dev_dbg instead of a dev_warn.
Users can still get a count of the number of timestamps dropped by
reading the ethtool statistics value, if necessary.
Change-ID: I35494442226a444c418dfb4f91a3070d06c8435c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the FEC status bits from the link up event into the
hw_link_info structure.
Change-ID: I9a7b256f6dfb0dce89c2f503075d0d383526832e
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently i40e_bus_info has PCI device and function info only and log
messages print device number as bus number. Added field to provide bus
number info and modified log statements to print bus, device and
function information.
Change-ID: I811617cee2714cc0d6bade8d369f57040990756f
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_client_prepare() can never return an error. So make it
void and quit checking its return value.
Change-ID: I9ff311e2324dde329eb68648efb2c94aaff856db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original comment implies that the only location where the raw_packet
buffer will be freed is in i40e_clean_tx_ring() which is incorrect. In
fact this isn't even the normal case. Update the comment explaining
where the memory is freed.
Change-ID: Ie0defc35ed1c3af183f81fdc60b6d783707a5595
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reorganize the i40e_pull_tail() logic, doing it in i40e_add_rx_frag()
where it's cheaper. The igb driver does this the same way.
Also renames i40e_page_is_reserved() to reflect what it actually
tests.
Change-ID: Icd9cc507aae1fcdc02308b3a09034111b4c24071
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reduces the size of struct i40e_rx_buffer by one pointer,
and makes the i40e driver a little more consistent with the igb driver
in terms of packets that span buffers.
We do this by moving the skb field from struct i40e_rx_buffer to
struct i40e_ring. We pass the skb we already have (or NULL if we
don't) to i40e_fetch_rx_buffer(), which skips the skb allocation if we
already have one for this packet.
Change-ID: I4ad48a531844494ba0c5d8e1a62209a057f661b0
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On packet RX, we perform a DMA sync for CPU before passing the
packet up. Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.
Change-ID: I626aaf6c37275a8ce9e81efcaa773f327b331487
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The iWarp client cannot continue until this operation has been completed
by the PF driver. Sleep (with timeout) until the reply from the PF
driver has been received.
Change-ID: I5dc41b857bba32d0218b7ce167b5da122dadf349
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can avoid the minor bit of work by calling check params after we
check for the client instance, since we're about to return early in
cases where we do not have a client.
Change-ID: I56f8ea2ba48d4f571fa331c9ace50819a022fa1c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If skb_padto failed the skb has been dropped already, so it was
consumed, but it doesn't mean it was sent, thus no need to update
queue tx time, etc. So, return NET_XMIT_DROP as more appropriate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the vni zero check for COLLECT_METADATA mode.
It is not really needed, vni zero is a valid vni.
Fixes: 3ad7a4b141 ("vxlan: support fdb and learning in COLLECT_METADATA mode"
Reported-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the dst->pending_confirm flag was removed, we do not
need anymore to provide dst arg to dst_neigh_output.
So, rename it to neigh_output as before commit 5110effee8
("net: Do delayed neigh confirmation.").
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: a0ee354148 ("sfc: process RX event inner checksum flags")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a tap character device driver that is based on the
IP-VLAN network interface, called ipvtap. An ipvtap device can be created
in the same way as an ipvlan device, using 'type ipvtap', and then accessed
using the tap user space interface.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes tap a separate module for other types of virtual interfaces, for example,
ipvlan to use.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extending tap APIs get/free_minor and create/destroy_cdev to handle more than one
type of virtual interface.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan object is re-structured to hold tap related elements in a separate
entity, tap_dev. Upon NETDEV_REGISTER device_event, tap_dev is registered with
idr and fetched again on tap_open. Few of the tap functions are modified to
accepted tap_dev as argument. tap_dev object includes callbacks to be used by
underlying virtual interface to take care of tx and rx accounting.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides tap device create/destroy APIs in tap.c.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming tap related APIs, data structures and macros in tap.c from macvtap_.* to tap_.*
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvtap module has code for tap/queue management and link management. This patch splits
the code into macvtap_main.c for link management and tap.c for tap/queue management.
Functionality in tap.c can be re-used for implementing tap on other virtual interfaces.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PF driver for NFP4000 and NFP6000.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF services multiple ports using single PCI device therefore
IRQs can no longer be allocated in the netdev code. Lower
portion of the driver has to allocate the IRQs and hand them
out to ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver will support multiple ports per PCI device, add port
number to DebugFS paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP Service Processor (NSP) is an ARM core inside the chip which
is responsible for management and control functions. Add support
for chip reset, FW load and external module access using the NSP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using application FW symbol table to look up
location of information in device memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIP is a vector of information which linker can optionally include
in application firmware. It will be used to retrieve the location
of symbol tables.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFFW info is a resource which contains information about
the loaded application firmware. Add code which will allow
us to decode it and retrieve MIP location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hwinfo is a simple key=value store of information which is read
from the flash and populated during chip power on. Add code to
look up information in it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource table is an array placed in a well defined location
in device's memory which describes device resources and contains
locks which have to be acquired to use them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command Push Pull is the name of NFP's network on a chip.
PCIe PF can access the interconnect through a number of mappings
controlled via Base Access Registers. BARs allow the PF to issue
pretty much any command or address any memory on the chip.
Add appropriate logic and a handful of helper for simple operations
like reading scalars from memories.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for the PF driver is about to be added and will share
much of the code. When the VF driver was added we planned to
maintain the PF driver as a separate module but have decided
that for our simple use case just maintaining a single module
is more reasonable. Rename the driver to just "nfp" and update
the Kconfig.
While at it remove latent references to NFP3200.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking at runtime that a value will fit inside
a specified field/mask.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sqkq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more updates:
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice and only for tx 0,
it's supposed to be done in netdev_start_xmit() and per tx queue.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel. There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.
Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.
This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix these errors reported by the 0-day builder by replacing the
linux/export.h include with linux/module.h.
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1463:1: warning: data definition has no type or storage class
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1463:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1468:1: warning: data definition has no type or storage class
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1468:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_exit' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1464:20: note: in definition of macro 'module_driver'
static void __exit __driver##_exit(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_init' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1459:19: note: in definition of macro 'module_driver'
static int __init __driver##_init(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
Add linux/module.h to both these files.
drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
Add linux/moduleparam.h to this file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'
Add linux/phy_fixed.h to fman_memac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant
Add linux/phy.h to bgmac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/usb/lan78xx.c:394:33: sparse: expected ; at end of declaration
drivers/net/usb/lan78xx.c:394:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/usb/lan78xx.c:394:33: sparse: got interface
drivers/net/usb/lan78xx.c:403:1: sparse: Expected ; at the end of type declaration
drivers/net/usb/lan78xx.c:403:1: sparse: got }
Add linux/phy.h to lan78xx.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly smaller changeds and fixes all over, nothing really major
standing out.
Major changes:
iwlwifi
* work on support for new A000 devices continues
* fix 802.11w, which was failing to due an IGTK bug
ath10k
* add debugfs file peer_debug_trigger for debugging firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYnHNpAAoJEG4XJFUm622b48QH/iQ7eCZMSYBOb3QIqJnpEkD/
k1xtch60J/JBTw11mS8TvvqyA19BnLZmLIIbbVWLTPeL5S4MJBGmEISHE9dc3FmY
CP//GjQYdxSm7VgZJSUKolQOIsY4kj/WuY4eoJzWiOfaloXHk0ascNrigdXCUSec
lRM8sX77KY/30qKJGN/Yc1ccT8zmRa/Skdt7JSHzNKakHiykqvR6NgRa6stf3g5K
NJAIrZO7K1Yndr187EsX4mr3ataAeo5+YHxoIReuYq2pcrZ6uSDsO3tJfC+4upqR
SrN/x6ds5SUYCKfwy0i/oxwuzYb8hWFH0m+yXhdkNPoaIyhgGHqzCVzdzbaqcDw=
=IyB5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
Mostly smaller changeds and fixes all over, nothing really major
standing out.
Major changes:
iwlwifi
* work on support for new A000 devices continues
* fix 802.11w, which was failing to due an IGTK bug
ath10k
* add debugfs file peer_debug_trigger for debugging firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not understand ETH_P_ALL. So treat this special case differently
and translate to 0/0 key/mask. That will allow HW to match all ethertypes.
Fixes: 7aa0f5aa90 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:
[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)
This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.
[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to update mc_disabled from switchdev attr
SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_orig_get returns the vport from the physical
port if needed, based on the original device.
This patch addresses the case where the original device is a bridge.
If it is vlan unaware bridge, it returns the matching vport. If it is vlan
aware bridge, there is no matching vport, and it returns the original port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.
If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.
Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user that wants many bridges will use 1.Q bridge which are scalable.
One can have as many 1.Q bridges as vfids.
This patch sets their number to 1k, which is a reasonably large number.
This change is done here because the next patches will add a new flood
table, and without it, it will increase the overall size of the flood
tables dramatically.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a per port flood update function only for the UC
table. Make the function more generic by changing the table type to be
an input.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flood set function can't operate on only one table, but
sets both uc_flood and mb_flood together.
This patch creates a function that sets the flood state per table.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon the reception of an ENTRY_REPLACE notification, resolve the FIB
node corresponding to the prefix and length and insert the new route
before the first matching entry.
Since the notification also signals the deletion of the replaced route,
delete it from the driver's cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new route is appended, it's placed after existing routes sharing
the same parameters (prefix, length, table ID, TOS and priority).
While the device supports only one route with the same prefix and length
in a single table, it's important to correctly place the appended route
in the driver's cache, as when a route is deleted the next one is
programmed into the device.
Following the reception of an ENTRY_APPEND notification, resolve the
FIB node corresponding to the prefix and length and correctly place the
new entry in its entry list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, routes are indexed in a routing table based on the prefix
and its length. This is in contrast to the kernel's FIB where several
FIB aliases can exist with these parameters being identical. In such
cases, the routes will be sorted by table ID (LOCAL first, then MAIN),
TOS and finally priority (metric).
During lookup, these routes will be evaluated in order. In case the
packet's TOS field is non-zero and a FIB alias with a matching TOS is
found, then it's selected. Otherwise, the lookup defaults to the route
with TOS 0 (if it exists). However, if the requested scope is narrower
than the one found, then the lookup continues.
To best reflect the kernel's datapath we should take the above into
account. Given a prefix and its length, the reflected route will always
be the first one in the FIB alias list. However, if the route has a
non-zero TOS then its action will be converted to trap instead of
forward, since we currently don't support TOS-based routing. If this
turns out to be a real issue, we can add support for that using
policy-based switching.
The route's scope can be effectively ignored as any packet being routed
by the device would've been looked-up using the widest scope (UNIVERSE).
To achieve that we need to do two changes. Firstly, we need to create
another struct (FIB node) that will hold the list of FIB entries sharing
the same prefix and length. This struct will be hashed using these two
parameters.
Secondly, we need to change the route reflection to match the above
logic, so that the first FIB entry in the list will be programmed into
the device while the rest will remain in the driver's cache in case of
subsequent changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the host info config to be the first admin command that is executed.
This change require the driver to remove the 'feature check'
from host info configuration flow.
The check is removed since the supported features bitmask field
is retrieved only after calling ENA_ADMIN_DEVICE_ATTRIBUTES admin command.
If set host info is not supported an error will be returned by the device.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeouts were too agressive and sometimes cause false alarms.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion descriptors are accessed from the driver and from the device.
To avoid reading the old value, use READ_ONCE macro.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not unamsk interrupts if we are in busy poll mode.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ena driver detects that the device is not behave as expected,
it tries to reset the device.
The reset flow calls ena_down, which will frees all the resources
the driver allocates and then it will reset the device.
This flow can cause memory corruption if the device is still writes
to the driver's memory space.
To overcome this potential race, move the reset before the device
resources are freed.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_get_stat64() can be called from atomic context, but the current
implementation sends an admin command to retrieve the statistics from
the device. This admin command can sleep.
This patch re-factors the implementation of ena_get_stats64() to use
the {rx,tx}bytes/count from the driver's inner counters, and to obtain
the rx drop counter from the asynchronous keep alive (heart bit)
event.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA default hash configures IPv4_frag hash twice instead of
configure non-IP packets.
The bug caused IPv4 fragmented packets to be calculated based on
L2 source and destination address instead of L3 source and destination.
IPv4 packets can reach to the wrong Rx queue.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_flow_data_to_flow_hash and ena_flow_hash_to_flow_type
treat the ena_flow_hash_to_flow_type enum as power of two values.
Change the values of ena_admin_flow_hash_fields to be power of two values.
This bug effect the ethtool set/get rxnfc.
ethtool will report wrong values hash fields for get and will
configure wrong hash fields in set.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENA driver tries to open a queue per vCPU.
To determine how many vCPUs the instance have it uses num_possible_cpus()
while it should have use num_online_cpus() instead.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove NETIF_F_NTUPLE from netdev->features.
The ENA device driver does not support ntuple filtering.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define ndo_features_check. Hw supports offload only for ipv4 inner and
ipv4 outer pkt.
Code refactor for setting inner tcp pseudo csum.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defines enic_udp_tunnel_add/del for configuring vxlan tunnel offload.
enic supports offload of only one ipv4/udp port.
There are two modes that fw supports for vxlan offload.
mode 0: fcoe bit is set for encapsulated packet. fcoe_fc_crc_ok is set
if checksum of csum is ok. This bit is or of ip_csum_ok and
tcp_udp_csum_ok
mode 2: BIT(0) in rss_hash is set if it is encapsulated packet.
BIT(1) is set if outer_ip_csum_ok/
BIT(2) is set if outer_tcp_csum_ok
tcp_udp_csum_ok/ipv4_csum_ok is set if inner csum is OK.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devcmds needed for vxlan offload. Implement 3 new devcmd
overlay_offload_ctrl: enable/disable offload
overlay_offload_cfg: update offload udp port number
get_supported_feature_ver: get hw supported offload version. Each
version has different bitmap for csum_ok/encap
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move it out from the middle for the #defines to just before it is
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the set_ringparam method, which allows the user to specify
the size of the TX and RX descriptor rings. The values are constrained
to the limits of the hardware.
Since the driver does not use separate queues for mini or jumbo frames,
attempts to set those values are rejected.
If the interface is already running when the setting is changed, then
the interface is reset.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_regs_len and get_regs ethtool methods. The driver
returns the values of selected hardware registers.
The make the register offsets known to emac_ethtool, the the register
offset macros are all combined into one header file. They were
inexplicably and arbitrarily split between two files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and
GENEVE UDP ports. Also reset the port list to empty on driver load and
on driver unload, with appropriate flag set on the unload case.
These port numbers are used for RX inner checksum offload, and in future
will also be used for TX inner checksum offload and encapsulated TSO.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function wasn't being called in this particular case when the MC
reboots. This caused resource reallocations to not be handled properly
and often ended up disabling the interface.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mainly to prepare for a future overlay networking patch that
could cause an MC reset at probe time if the UDP tunnel port list is
set immediately upon driver load.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the csum_level for encapsulated packets where the encapsulation
type, l3 class and l4 class are sets that need it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload of encapsulated packets. This
essentially just means paying attention to the inner checksum flags
in the RX event, and if *either* checksum flag indicates a fail then
don't tell the kernel that checksum offload was successful.
Also, count these checksum errors and export the counts to ethtool -S.
Test the most common "good" case of RX events with a single bitmask
instead of a series of ifs. Move the more specific error checking
in to a separate function for clarity, and don't use unlikely() there
since we know at least one of the bits is bad.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 90c311b0ee ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0ee (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case where there is no phydev attached
to a LMAC in DT due to non-existance of a PHY driver or due
to usage of non-stanadard PHY which doesn't support autoneg.
Changes dependeds on firmware to send correct info w.r.t
PHY and autoneg capability.
This patch also covers a case where a 10G/40G interface is used
as a 1G with convertors with Cortina PHY in between.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel resolves the nexthops for a given route using
FIB_LOOKUP_IGNORE_LINKSTATE which means a notification can be sent for a
route with one of its nexthops being LINKDOWN.
In case IGNORE_ROUTES_WITH_LINKDOWN is set for the nexthop netdev, then
we shouldn't reflect the nexthop to the device's table.
Once the nexthop netdev's carrier goes up we'll be notified using NH_ADD
and reflect it to the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last IP address is removed from a netdev, its RIF is deleted.
However, if user didn't first remove neighbours and nexthops using this
interface, then they would still be present in the device's tables.
Therefore, whenever a RIF is deleted, make sure all the neighbours and
nexthops (adjacency entries) using it are removed from the relevant
tables as well.
The action associated with any route using this RIF would be refreshed,
most likely to trap. If the kernel decides to remove the route (f.e.,
because all the nexthops are now DEAD), then an event would be sent,
causing the route to be removed from the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet hits a multipath route in the device's routing table, a
hash is computed over its headers, which is then used to select the
appropriate nexthop from the device's adjacency table.
There are situations in which the kernel removes a nexthop from a
multipath route (e.g., no carrier) and the device should do the same.
Upon the reception of NH_{ADD,DEL} events, add or remove a nexthop from
the device's adjacency table and refresh all the routes using the
nexthop group. If all the nexthops of a multipath route are invalid,
then any packet hitting the route would be trapped to the CPU for
forwarding.
If all the nexthops are DEAD, then the kernel would remove the route
entirely. On the other hand, if all the nexthops are merely LINKDOWN,
then the kernel would keep the route and forward any incoming packet
using a different route.
While the last case might sound like a problem, it's expected that a
routing daemon running in user space would remove such a route from the
FIB as it's dumped with the DEAD flag set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device can have one of three actions associated with a route:
1) Remote - packets continue to the adjacency table
2) Local - packets continue to the neighbour table
3) Trap - packets continue to the CPU
The first two actions can also trap packets to the CPU, but they do so
using a different trap ID, which has a lower traffic class and less
allotted bandwidth.
We currently use the third action for both RTN_{LOCAL,BROADCAST} routes
and RTN_UNICAST routes not pointing to the switch ports.
However, packets that merely need to be forwarded by the switch are
likely not control packets and can be therefore scheduled towards the
CPU using a lower traffic class.
Achieve the above by assigning the third action only to local and
broadcast routes and have any other route use either of the first two
actions, based on whether the route is gatewayed or not.
This will also allow us to refresh routes using the local action and
have them trap packets when their RIF is no longer valid following a
NH_DEL event.
One side effect of this patch is that we no longer give special
treatment to multipath routes using both switch and non-switch ports
towards their nexthops. If at least one of the nexthops can be resolved,
then the device will forward the packets instead of trapping them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a generic function to determine whether a
route should be offloaded or not. Make use of it here.
In the future we're going to add more conditions to this test (e.g.,
whether TOS is non-zero), so it makes sense to centralize it instead of
open coding it in a few places.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently set the RTNH_F_OFFLOAD flag for all routes using remote
action, but this isn't always correct. If none of the nexthops
associated with a gatewayed route can be offloaded into the device, then
any packet hitting it would be trapped to the CPU and forwarded by the
kernel.
Solve this by pushing the setting of the offload flag to after the route
was programmed into the device, thereby allowing us to take all the
parameters into account.
This change will also help us further in the patchset, when we refresh
routes following the reception of NH_{ADD,DEL} events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop init and de-init functions both have symmetric parts
concerned with the reflection of the neighbour entry into the device's
adjacency table, in case it's used by a gatewayed route.
These sections of code also need to be called when a nexthop is marked
as valid / invalid following NH_{ADD,DEL} events. Break these out into
appropriate functions, so that they could be invoked following the
reception of above events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
