This patch enables RTC on stm32f429-disco with LSI as clock source because
X2 crystal for LSE is not fitted by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch include auxiliary clock definition (clocks which are not derived
from system clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds an external I2S clock in the DT.
The I2S clock could be derived from an external I2S clock or by I2S pll.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Enable analog to digital converter on stm32f429i-eval board.
It has on-board potentimeter wired to ADC3 in8 analog pin and
uses fixed regulator to provide reference voltage.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds USART3 pin configuration on PB10/PA11 pins
for STM32F469I-DISCO board.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch fix memory size to support 16MB of external SDRAM.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This adds a device tree definition file for LEGO MINDSTORMS EV3.
What is working:
* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input port 1
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* USB host port
* USB peripheral port
What is not working/to be added later:
* Speaker - have patch submitted to get pwm-beeper working - maybe someday
it will have a real sound driver that uses PRU
* A/DC chip - have driver submitted and accepted - waiting for ack on
device tree bindings
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock
* Input and output ports - need some sort of new phy or extcon driver as
well as PRU UART and PRU I2C drivers
* Battery indication - needs new power supply driver
Note on flash partitions:
These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create
their own firmware image with different partitioning, they can use a modern
U-Boot in their own firmware image that modifies the device tree with the
custom partitions.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
please pull the following changes:
- Rafal enables the UART by default on all BCM5301x, BCM4708, BCM4709 since
every device found out there has it enabled by default. He also fixes the
LED definitions for the Luxul XWR-3100 device, enables USB controllers and
their respective PHY devices, specifies the correct GPIO to power on USB
HUBs, adds the additional RAM bank for somes devices, and finally sets the
correct 5Ghz frequency limits on the Netgear R8000
- Jon does a number of Norsthar Plus SoC cleanups, fixes NAND partitions unit
addresses, adds QSPI support to a bunch of boards, adds Ethernet switch ports
to the BCM958625K reference board, enables 3rd Ethernet MAC instance to
relevant DTSes, enables Ethernet on the XMC board, and finally adds SD/MMC
support to the XMC board
- Boris adds the Video Encoder nodes to the Raspberry Pi DTS include files
ands enables it on the relevant boards
- Dan adds support for two new Luxul devices: XAP-1410 and XWR-1200, both
BCM47081 based SoCs
-----BEGIN PGP SIGNATURE-----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=wFmP
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree' of http://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.11,
please pull the following changes:
- Rafal enables the UART by default on all BCM5301x, BCM4708, BCM4709 since
every device found out there has it enabled by default. He also fixes the
LED definitions for the Luxul XWR-3100 device, enables USB controllers and
their respective PHY devices, specifies the correct GPIO to power on USB
HUBs, adds the additional RAM bank for somes devices, and finally sets the
correct 5Ghz frequency limits on the Netgear R8000
- Jon does a number of Norsthar Plus SoC cleanups, fixes NAND partitions unit
addresses, adds QSPI support to a bunch of boards, adds Ethernet switch ports
to the BCM958625K reference board, enables 3rd Ethernet MAC instance to
relevant DTSes, enables Ethernet on the XMC board, and finally adds SD/MMC
support to the XMC board
- Boris adds the Video Encoder nodes to the Raspberry Pi DTS include files
ands enables it on the relevant boards
- Dan adds support for two new Luxul devices: XAP-1410 and XWR-1200, both
BCM47081 based SoCs
* tag 'arm-soc/for-4.11/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Enable the VEC IP on all RaspberryPi boards
ARM: dts: bcm283x: Add VEC node in bcm283x.dtsi
ARM: dts: BCM5301X: Add DT for Luxul XWR-1200
ARM: dts: BCM5301X: Add DT for Luxul XAP-1410
ARM: dts: BCM5301X: Set 5 GHz wireless frequency limits on Netgear R8000
ARM: dts: NSP: Add SD/MMC support
ARM: dts: NSP: Add Ethernet to NSP XMC
ARM: dts: NSP: Add and enable amac2
ARM: dts: NSP: Add BCM958625K switch ports
ARM: dts: NSP: Add QSPI support to missing boards
ARM: dts: NSP: Correct NAND partition unit address
ARM: dts: NSP: DT Clean-ups
ARM: dts: BCM53573: Specify USB ports of on-SoC controllers
ARM: dts: BCM5301X: Specify all RAM by including an extra block
ARM: dts: BCM5301X: Set GPIO enabling USB power on Netgear R7000
ARM: dts: BCM5301X: Specify USB controllers in DT
ARM: dts: BCM5301X: Fix LAN LED labels for Luxul XWR-3100
ARM: dts: BCM5301X: Enable UART by default for BCM4708(1), BCM4709(4) & BCM53012
Signed-off-by: Olof Johansson <olof@lixom.net>
Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.
This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.
Cc: stable@vger.kernel.org
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net:
dsa: Document new binding"). The legacy binding node is kept included, but is
marked disabled.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Cc: stable <stable@vger.kernel.org> #v4.1+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.
Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2E SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.
Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2L SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.
Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2H SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Power Sleep Controller (PSC) module is responsible
for the power and clock management for each of the peripherals
present on the SoC. Represent this as a syscon node so that
multiple users can leverage it for various functionalities.
Signed-off-by: Suman Anna <s-anna@ti.com>
[afd@ti.com: add simple-mfd compatible]
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Fix the pa clock to point to the clkpa which has clock rate of 1/3 of PA
PLL clock and add clock names.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The serial IPs in Rockchip socs are based on Designware uarts and thus
bind against the snps,dw-apb-uart compatible.
On all newer socs we also carry around per-soc compatibles that allow
us to have more specific drivers in the future - if needed.
The cortex-a9 socs rk3066 and rk3188 that were added first don't have
those yet, so add them for completenes sake.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the VEC IP on all RaspberryPi boards.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the VEC (Video EnCoder) node definition in bcm283x.dtsi.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Luxul XWR-1200 in a dual-band router based on BCM47081. It uses serial
flash (for bootloader and NVRAM) and NAND flash (for firmware).
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Luxul XAP-1410 in a dual-band access point device based on BCM47081 with
serial flash. It has 3 LEDs and just one (reset) button.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Netgear R8000 is a tri-band home router. It has three BCM43602 chipsets
two of them for 5 GHz band. Both seem the same and their firmwares
report the same set of channels. The problem is due to hardware / board
design there are extra limitations that should be respected.
First PHY should be used for U-NII-2 and U-NII-3. Third PHY should be
used for U-NII-1. Using them in a different way may result in wireless
not working or in noticeably reduced performance. Basic version of this
info was provided by Broadcom employee, then it has been verified by me
using original vendor firmware (which has limitations hardcoded in UI).
This patch uses recently introduced ieee80211-freq-limit property to
describe these limitations at DT level.
Referencing PCIe devices in DT required specifying all related bridges.
Below you can see (a bit complex) PCI tree from R8000 that explains all
entries that I needed to put in DT.
0000:00:00.0 14e4:8012 Bridge Device
└─ 0000:01:00.0 14e4:aa52 Network Controller
0001:00:00.0 14e4:8012 Bridge Device
└─ 0001:01:00.0 10b5:8603 Bridge Device
├─ 0001:02:01.0 10b5:8603 Bridge Device
│ └─ 0001:03:00.0 14e4:aa52 Network Controller
├─ 0001:02:02.0 10b5:8603 Bridge Device
│ └─ 0001:04:00.0 14e4:aa52 Network Controller
├─ 0001:02:03.0 000d:0000 0x000000
├─ 0001:02:04.0 000d:0000 0x000000
├─ 0001:02:05.0 000d:0000 0x000000
├─ 0001:02:06.0 000d:0000 0x000000
├─ (...)
├─ 0001:02:1d.0 000d:0000 0x000000
├─ 0001:02:1e.0 000d:0000 0x000000
└─ 0001:02:1f.0 000d:0000 0x000000
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add SD/MMC support to the Broadcom NSP SVK and XMC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable the ethernet in the NSP XMC (bcm958525xmc) device tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add and enable the third AMAC ethernet interface in the device trees for
the platforms where it is present. Also, enable amac1 on some of the
platforms where that was missing.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the layout of the switch ports found on the BCM958625K reference
board. The CPU port is hooked up to the AMAC0 Ethernet controller
adapter.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
QSPI device tree entries are present in bcm958625k, but missing from
bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
bcm958625hr, and bcm988312hr. Duplicate the entry in bcm958625k for
all of those that are missing it (as they are identical).
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The NAND partition unit address does not match the other NSP device tree
files. This change makes them uniform.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The QSPI entry was added out of the sequental order that the rest of the
DTSI file is in. Move it to make it fit in properly. Also, some other
entries have been added in a non-alphabetical order in the DTS files,
making them different from the other NSP DTS files. Move the relevant
peices to make it match. Finally, remove errant new lines.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom OHCI and EHCI controllers always have 2 ports each on the root
hub. Describe them in DT to allow specifying extra info or referencing
port nodes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The first 128 MiB of RAM can be accessed using an alias at address 0x0.
In theory we could access whole RAM using 0x80000000 - 0xbfffffff range
(up to 1 GiB) but it doesn't seem to work on Northstar. For some reason
(hardware setup left by the bootloader maybe?) 0x80000000 - 0x87ffffff
range can't be used. I reproduced this problem on:
1) Buffalo WZR-600DHP2 (BCM47081)
2) Netgear R6250 (BCM4708)
3) D-Link DIR-885L (BCM47094)
So it seems we're forced to access first 128 MiB using alias at 0x0 and
the rest using real base address + 128 MiB offset which is 0x88000000.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is one GPIO controlling power for both USB ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There are 3 separated controllers, one per USB /standard/. With PHY
drivers in place they can be simply supported with generic drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
They were named incorrectly most likely due to copy & paste mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Every device tested so far got UART0 (at 0x18000300) working as serial
console. It's most likely part of reference design and all vendors use
it that way.
It seems to be easier to enable it by default and just disable it if we
ever see a device with different hardware design.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This introduces the first OpenPower Power9 BMC system, Romulus. Romulus is
based on the ast2500 SoC from Aspeed.
These commits also add newly upstreamed drivers to the Palmetto BMC and ast2500
eval board. We now have working network, ipmi bt, gpio and pinmux on all platforms.
ARM: dts: aspeed: Add Romulus BMC platform
ARM: dts: aspeed: Add ftgmac100 to g4 and g5 platforms
ARM: dts: aspeed: Correct palmetto device tree
ARM: dts: aspeed: Reserve framebuffer memory
ARM: dts: aspeed-g5: Add gpio controller to devicetree
ARM: dts: aspeed-g5: Add syscon and pin controller nodes
ARM: dts: aspeed-g5: Add LPC Controller node
ARM: dts: aspeed-g5: Add SoC Display Controller node
ARM: dts: aspeed-g4: Add gpio controller to devicetree
ARM: dts: aspeed-g4: Add syscon and pin controller nodes
-----BEGIN PGP SIGNATURE-----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=BeSl
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.11-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Aspeed devicetree updates for 4.11
This introduces the first OpenPower Power9 BMC system, Romulus. Romulus is
based on the ast2500 SoC from Aspeed.
These commits also add newly upstreamed drivers to the Palmetto BMC and ast2500
eval board. We now have working network, ipmi bt, gpio and pinmux on all platforms.
* tag 'aspeed-4.11-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add Romulus BMC platform
ARM: dts: aspeed: Add ftgmac100 to g4 and g5 platforms
ARM: dts: aspeed: Correct palmetto device tree
ARM: dts: aspeed: Reserve framebuffer memory
ARM: dts: aspeed-g5: Add gpio controller to devicetree
ARM: dts: aspeed-g5: Add syscon and pin controller nodes
ARM: dts: aspeed-g5: Add LPC Controller node
ARM: dts: aspeed-g5: Add SoC Display Controller node
ARM: dts: aspeed-g4: Add gpio controller to devicetree
ARM: dts: aspeed-g4: Add syscon and pin controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
omap1, and then a handful of trivial fixes for boards and devices to
work:
- Fixes TI wilink bluetooth strange platform data baud rate
- Remove duplicate pinmux line for am335x-icev2
- Fix omap1 dma regression
- Fix uninitialized return value for wkup_m3_ipc_probe()
- Fix Ethernet PHY binding typo for dra72-evm
- Fix init for omap5 and dra7 sata ports
- Fix mmc card detect pin for Logic PD SOM-LV
-----BEGIN PGP SIGNATURE-----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=VJaM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.10-rc cycle. Mostly a DMA regression fix for
omap1, and then a handful of trivial fixes for boards and devices to
work:
- Fixes TI wilink bluetooth strange platform data baud rate
- Remove duplicate pinmux line for am335x-icev2
- Fix omap1 dma regression
- Fix uninitialized return value for wkup_m3_ipc_probe()
- Fix Ethernet PHY binding typo for dra72-evm
- Fix init for omap5 and dra7 sata ports
- Fix mmc card detect pin for Logic PD SOM-LV
* tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
Signed-off-by: Olof Johansson <olof@lixom.net>
While the SinA31s does have a proper 5-pin mini USB OTG port, the ID
pin does not seem to work. The pin used in the schematics is always low,
regardless of the attached OTG cable or SoC internal pin bias settings.
The v1.5 board is missing bias resistors shown in the schematics for
earlier revisions, and the connections of the remaining one does not
match the schematics either.
In addition, VBUS for this port is disconnected from the board's 5V
power rail. The board features a pad to solder jumper pins to connect
VBUS to 5V manually.
Given the above and the fact that the board has 5 more USB host ports,
it makes more sense to have the OTG port work in peripheral mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This fixes commit ab8dd3aed0 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV") where the Card Detect and Write Protect
pins were improperly configured.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Add support for the ethernet switch on the Turris Omnia board
- Clean up and improvement for ClearFog boards
- Correct license text which was mangled when switching to dual license
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWHkIIiMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71WLCAKCGlNI2NPYq
/54Ln14bXataT3uAVgCdF5DLhRKp24ifepK6hDF39drKdWk=
=zoka
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.11-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.11 (part 1)
- Add support for the ethernet switch on the Turris Omnia board
- Clean up and improvement for ClearFog boards
- Correct license text which was mangled when switching to dual license
* tag 'mvebu-dt-4.11-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: turris-omnia: add support for ethernet switch
ARM: dts: armada388-clearfog: move uart nodes
ARM: dts: armada388-clearfog: move ethernet related nodes
ARM: dts: armada388-clearfog: move I2C nodes
ARM: dts: armada388-clearfog: move device specific pinctrl nodes
ARM: dts: armada388-clearfog: add pro model DTS file
ARM: dts: armada388-clearfog: add base model DTS file
ARM: dts: armada388-clearfog: move rear button
ARM: dts: armada388-clearfog: move SPI CS1
ARM: dts: armada388-clearfog: move second PCIe port
ARM: dts: armada388-clearfog: move DSA switch
ARM: dts: armada388-clearfog: split clearfog DTS file
ARM: dts: armada388-clearfog: move sdhci pinctrl node to microsom
ARM: dts: armada388-clearfog: move SPI flash into microsom
ARM: dts: armada388-clearfog: fix SPI flash #size-cells
ARM: dts: mvebu: Correct license text
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Fixes for initial audio clocks configuration.
2. Enable sound on Odroid-X board.
3. Enable DMA for UART modules on Exynos5 SoCs.
4. Add CPU OPPs for Exynos4412 Prime (newer version of Exynos4412). This pulls
necessary change in the clocks.
5. Remove Exynos4212. We do not have any mainline boards with it. This will
simplify few bits later.
-----BEGIN PGP SIGNATURE-----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=w/rg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.11:
1. Fixes for initial audio clocks configuration.
2. Enable sound on Odroid-X board.
3. Enable DMA for UART modules on Exynos5 SoCs.
4. Add CPU OPPs for Exynos4412 Prime (newer version of Exynos4412). This pulls
necessary change in the clocks.
5. Remove Exynos4212. We do not have any mainline boards with it. This will
simplify few bits later.
* tag 'samsung-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: remove Exynos4212 support (dead code)
ARM: dts: exynos: Add CPU OPPs for Exynos4412 Prime
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
ARM: dts: exynos: Enable DMA support for UART modules on Exynos5 SoCs
ARM: dts: exynos: Cleanup Odroid-X2 and enable sound on Odroid-X
ARM: dts: exynos: Fix initial audio clocks configuration on Exynos4 boards
ARM: dts: exynos: Correct clocks for Exynos4 I2S module
Signed-off-by: Olof Johansson <olof@lixom.net>
- Adds FPGA manager bits
- Enable I2C on Cyclone5 and Arria5 devkits
- Adds LED support on C5/A5 devkits
- Enables CAN on C5 devkit
- Enables watchdog
- Add NAND on Arria10
- Add the LTC2977 Power Monitor on Arria10 devkit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hbau
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.11_part_1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.11, part 1
- Adds FPGA manager bits
- Enable I2C on Cyclone5 and Arria5 devkits
- Adds LED support on C5/A5 devkits
- Enables CAN on C5 devkit
- Enables watchdog
- Add NAND on Arria10
- Add the LTC2977 Power Monitor on Arria10 devkit
* tag 'socfpga_dts_for_v4.11_part_1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add missing compatible string for SDRAM controller
ARM: dts: socfpga: add fpga region support on Arria10
ARM: dts: socfpga: add base fpga region and fpga bridges
ARM: dts: socfpga: fpga manager data is 32 bits
ARM: dts: socfpga: Add NAND device tree for Arria10
ARM: dts: socfpga: add fpga-manager node for Arria10
ARM: dts: socfpga: add the LTC2977 power monitor on Arria10 devkit
ARM: dts: socfpga: enable watchdog timer on Arria5 and Arria10
ARM: dts: socfpga: enable CAN on Cyclone5 devkit
ARM: dts: socfpga: Add Rohm DH2228FV DAC
ARM: dts: socfpga: set desired i2c clock on Cyclone5 and Arria5 devkits
ARM: dts: socfpga: enable GPIO and LEDs for Cyclone5 and Arria5 devkits
Signed-off-by: Olof Johansson <olof@lixom.net>
pull the following:
- Jon fixes an invalid value for the "ranges" property of the bus nodes on NorthStar
Plus SoCs
-----BEGIN PGP SIGNATURE-----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=ufJA
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.10/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for v4.10, please
pull the following:
- Jon fixes an invalid value for the "ranges" property of the bus nodes on NorthStar
Plus SoCs
* tag 'arm-soc/for-4.10/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Fix DT ranges error
Signed-off-by: Olof Johansson <olof@lixom.net>
A few fixes here and there to enable the build of some DT leftover, prevent
display issues or setup a proper muxing.
-----BEGIN PGP SIGNATURE-----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=6kp8
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.10
A few fixes here and there to enable the build of some DT leftover, prevent
display issues or setup a proper muxing.
* tag 'sunxi-fixes-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of Nitrogen6 device tree fixes for audio codec probe
failure, which is caused by that pinctrl setting for codec clock
was not in the correct device node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYdJEnAAoJEFBXWFqHsHzOSn4H/i21NWVegzZVjm1wmkPR/ddr
OSih7TUd7HsdFx/8S8u66L9mpmQTHRlBAxPLZFuTwvt3NtPtvJpbteDCkfbYMQg6
jxbiew8MbSRY/v+vTNVemiiIIzc5yMi9U2PFTHmg1cHsDd6mIe4nlxA+sXsZQ2Yi
jHTbkL7mF441I4yqVIw8yXauIZKCSPOW5mDk/nKCd4Nk51KZmT9kFDz34ohNC7cc
UckUPC/1qoWo2idt5Uh+DxG7RdyywQaGujxIucwfQhOzDxpDMmcD+pXtUqdQygRq
ykFC82Y4yg5IDtBkncK4d6yG7L1pptTBPUT2LV/xqfUG6FWXMbNMSXI53jY/UqA=
=Ds9k
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.10, 2nd round:
- A couple of Nitrogen6 device tree fixes for audio codec probe
failure, which is caused by that pinctrl setting for codec clock
was not in the correct device node.
* tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables RTC on stm32f429-disco with LSI as clock source because
X2 crystal for LSE is not fitted by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add initial set of CoreSight components found on Qualcomm apq8064 based
platforms, including the IFC6410 board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the MPU-3050 gyroscope and the KXSD9 accelerometer to
the Qualcomm APQ8060 Dragonboard. The KXSD9 is mounted beyond the
MPU-3050 and appear as a subdevice beyond it. We set up the
required GPIO and interrupt lines to make the devices work.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Some nodes are referencing the pm8058_gpio as IRQ parent, but
the HW IRQ offset they are supplying is actually that for the
parent to that controller: the PM8058 itself. Since that is the
proper parent, reference it directly.
We can switch this to the pm8058_gpio and the proper offset
once we have fixed the SSBI GPIO driver to properly deal with
the hierarchical IRQ domain and get proper local offset
translation.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The name "pmicintc" is ambiguous: there is a second power
management IC named PM8901 on these systems, and it is also
an interrupt controller. To make things clear, just name the
node alias "pm8058", this in unambigous and has all information
we need.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables 1.8v regulator on LS expansion, which should be
always on according to 96boards spec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch moves hdmi pinctrl defination from board file to soc level
pinctrl file. If not this pinctrl setup will be duplicated across all
the apq8064 based board files.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the missing properties for pm8921 smps2.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add nodes for the Riva PIL, IRIS RF module, BT and WiFI services exposed
by the Riva firmware and the related memory reserve.
Also provides pinctrl nodes for devices enabling the riva-pil.
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The ipq board has these rates as 25MHz, and not 19.2 and 27. I
copy/pasted from other boards that have those rates but forgot
to fix the rates here.
Fixes: 30fc4212d5 ("arm: dts: qcom: Add more board clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
sources for msm8974, this isn't actually a reserved region.
Instead it's marked as "unused" for reserved regions. Let's
remove it so we get back a good chunk of memory.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the necessary nodes for USB gadget on MSM8974 and enable these for
Honami.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
AHCI provides the register PORTS_IMPL to let the software know which port
is supported. The register must be initialized by the bootloader. However
in some cases u-boot doesn't properly initialize this value (if it is not
compiled with SATA support for example or if the SATA initialization fails).
The DTS entry "ports-implemented" can be used to override the value in
PORTS_IMPL.
Without this patch the SATA will not work in the following two cases:
* if there has been a failure to initialize SATA in u-boot.
* if ahci_platform module has been removed and re-inserted. The reason is
that the content of PORTS_IMPL is lost after the module is removed.
I suspect that it's because the controller is reset by the hwmod.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated comments with what goes wrong]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add mt2701 nand device node, include nfi and bch ecc.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the dtsi node of iommu and smi for mt2701.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch rearrange MT2701 DT nodes to keep them in ascending order.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
[mb: fix pio unit address and order]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
TI DA8xx/OMAPL13x/AM17xx/AM18xx SoCs have extra UART registers beyond
the standard 8250 registers, so we need a new compatible string to
indicate this. Also, at least one of these registers uses the full 32
bits, so we need to specify reg-io-width in addition to reg-shift.
"ns16550a" is left in the compatible specification since it does work
as long as the bootloader configures the SoC UART power management
registers.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The range size for axi is 0x2 bytes too small, as the QSPI needs
0x11c408 + 0x004 (which is 0x0011c40c, not 0x0011c40a). No errors have
been observed with this shortcoming, but fixing it for correctness.
Fixes: 329f98c197 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
FDT harcoded partition table does not match that one in historical
TI's 2.6.37 kernel and non legacy kernels even use different ECC scheme,
yet noone complained, so remove it altogether.
Also, UBI volumes instead of partitions are used since u-boot-2016.09.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the bootloader passes the NAND and the SPI flash partition tables
there is no need to keep them in the kernel device tree.
Removed them.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TI DRA72-EVM Rev C has two DP83867 ethernet phys which support IRQ
generation in case of phy/link status changes. The INT/PWDN lines from both
DP83867 phys are wired to DRA7 gpio6.16, so reflect the same in DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in impedance setting for ethernet-phy@3
Fixes: b76db38cd8 ("ARM: dts: dra72-evm-revc: add phy impedance settings")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename dmu_reserved to delta_reserved
Rename st231_dmu to st231_delta
Update the delta_reserved memory region start address
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The clock parent was lower than child clock which is not correct.
In some use case, it leads to division by zero.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Previously, the sun8i tablets used everything declared in AXP221 DTSI
while they have an AXP223 PMIC.
This corrects that so the sun8i tablets can get some features the AXP223
has (at the moment, ability to have 100mA as maximal current on VBUS
power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Allwinner Parrot R16 used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Allwinner Parrot R16 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Sinlinx SinA33 used everything declared in AXP221 DTSI
while it has an AXP223 PMIC.
This corrects that so the Sinlinx SinA33 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Olimex A33-OlinuXino used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Olimex A33-OlinuXino can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP223 shares most of its logic with the AXP221 but it has some
differences for the VBUS driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As sti-hda is only available on STiH410-B2120,
disable it in STiH410.dtsi and enable it at board level.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
There are no Exynos4212 based boards in mainline, so there is no need to
keep additional files for SoCs, which are never used. This patch removes
support for Exynos4212 SoCs and moves previously shared Exynos4412
definitions to a single file to simplify future maintenance.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Banana Pro has an AMPAK AP6181 WiFi+Bluetooth module. The WiFi part
is a BCM43362 IC connected to MMC3 of the A20 SoC via SDIO. The IC also
takes a power enable signal via GPIO.
This commit adds a device-tree node to power it up, so the mmc subsys
can scan it, and enables the mmc controller which is connected to it.
As the wifi enable pin of the AP6181 module is not really a regulator,
switch the mmc3 node to the mmc-pwrseq framework for controlling it.
This more accurately reflectes how the hardware actually works.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the S/PDIF transmitter that is present on the Mele I7.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC routes the LINEOUT pins to the audio out jack on the
board. The onboard microphone is routed to MIC1, with MBIAS providing
power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support the audio codec found on the Allwinner H3 SoC, add
device nodes for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Q8 tablets have an internal mono speaker w/ external amp
which has a shutdown control tied to a GPIO pin. Both the speaker
amp and the headphone jack are tied to the HP output pins. While
the speaker is mono, the headset jack is stereo. Unfortunately
the driver does not support automatic switching of this.
In addition, the headset is DC coupled, or "direct drive" enabled.
The headset's microphone is tied to MIC2 with HBIAS providing power.
A separate internal microphone is tied to MIC1 with MBIAS providing
power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a device tree binding and driver for the A23's
internal audio codec, add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A23/A33, the internal codec's analog path controls are located in
the PRCM node.
Add a sub-device node to the PRCM for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UEXT are Universal EXTension connector from Olimex. They embed i2c, spi
and uart pins along power in one connector and are found on most,
if not all, Olimex boards.
The Olimex A20 SOM EVB have two UEXT connector so enable the nodes found on
those two connectors.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on the A20 SoC
on the Banana Pro board.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
others three only have 1.
Add the num-cs property to each node.
The current driver doesn't read this property but this is useful for
downstream user of DTS (FreeBSD for example).
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use axp209.dtsi in sun7i-a20-olinuxino-lime2.dts and correct
some regulators.
DCDC2 is used for vdd-cpu so it should never be bellow 1V and above 1.4V
DCDC3 is used for VDD_INT so same as above.
LD01 is used for the RTC, and should have a typical value of 1.3V
LD02 is used for AVCC and should have a typical value of 3.0V
LD03/4 are used for Port-E/Port-G Power pin, and the schematics recommands
to set them to 2.8V as they can be used for CSI0/1.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi One is a low-cost Allwinner A13-based development board, with
an AXP209 PMU, a USB2.0 OTG port, a USB2.0 host port (or an onboard
RTL8723BU Wi-Fi card), optional headers for LCD and CSI, two GPIO
headers and two MicroSD card slots (connected to mmc0 and mmc2, both
bootable).
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some board only use 4bit mode of mmc2.
Add a pinctrl node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block to the A31 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF TX pin to the A31 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 has an audio jack for the SoC's internal codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
XR819 seems to need a delay after its reset line to be deasserted,
otherwise it may not respond MMC commands correctly, and fail to
initialize.
Add a 200ms delay in the mmc-pwrseq.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
An operating point table is needed for the cpu frequency adjusting to
work.
The operating point table is converted from the common value in
extracted script.fex from many A33 board/tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All reference design A33 tablets uses DCDC2 of AXP223 as the power
supply of the Cortex-A7 cores.
Set the cpu-supply in the DTSI of sun8i reference tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A "cpu0" label is needed on cpu@0 for cpufreq-dt to work.
Add such a label, in order to prepare for cpufreq support of A23/33.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Zero is a board that came with the new Allwinner H2+ SoC and a
SDIO Wi-Fi chip by Allwinner (XR819).
Add a device tree file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 Hummingbird has a mini USB OTG port, and uses GPIO pins from the
SoC for ID pin and VBUS detection and VBUS control. The PMIC can also do
VBUS detection and control.
Here we prefer to use the PMIC's DRIVEVBUS function to control VBUS for
USB OTG, as that is the hardware default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the past, all the MMC pins had
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.
Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The node name for the power seq pin is mmc2@0 like the mmc2_pins_a one.
This makes the original node (mmc2_pins_a) scrapped out of the dtb and
result in a unusable eMMC if U-Boot didn't configured the pins to the
correct functions.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we disable the display engine by default, we need to re-enable
it for the Hummingbird A31, which already had its display pipeline
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While we now support the internal display pipeline found on sun6i, it
is possible that we are unable to enable the display for some boards,
due to a lack of drivers for the panels or bridges found on them. If
the display pipeline is enabled, the driver will try to enable, and
possibly screw up the simple framebuffer U-boot had configured.
Disable the display pipeline by default.
Fixes: 6d0e5b70be ("ARM: dts: sun6i: Add device nodes for first
display pipeline")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Axentia TSE-850 is a SAMA5D3-based device designed to generate
FM subcarrier signals.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts is
listed as below.
1. The USB host nodes are removed, that is, the USB host is disabled.
2. The gpio_keys node is added to wake up from the sleep.
3. The LCD isn't supported due to the pins for LCD are conflicted
with gpio_keys.
4. The adc0 node support the pinctrl sleep state to fix the over
consumption on VDDANA.
As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The sama5d2 SoC has Synchronous Serial Controller which provides
synchronous communication link with external devices.
It's generally used in audio and telecom applications such as
I2S, Short Frame Sync, Long Frame Sync.
Signed-off-by: Alex Gershgorin <alex.gershgorin@qcore.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use DMA for UART3 as we have enough channels and to show how to
specify DMA use with serial nodes.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that DMA1 is defined, use it to distribute channel usage among the two
controllers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The sama5d2 SoC has a second DMA controller and can be used just like DMA0.
By default both DMA controllers are configured as "Secure" in
MATRIX_SPSELR so we can use whichever we want in a "single Secure World"
configuration.
Surprisingly the DMA1 has a lower address than DMA0. To avoid confusion
place it after DMA0 node anyway.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Enable UART1 and use DMA configuration with it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some peripherals are "Programmable Secure" but left as "Secure" by default.
If tried to be connected to Non-Secure DMA controller, the possibility to
leak secure data is prevented so using these peripherals with DMA1 is not
possible with this default configuration (MATRIX_SPSELR registers setup by
bootloader).
Move them to DMA0 which is an "Always-Secure" DMA controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The new size (0x100) also matches the size given in sama5d3.dtsi
Documentation reference: section 43.6 "Universal Asynchronous
Receiver Transmitter (UART) User Interface", table 43-4 "Register
Mapping" in [1].
[1] Atmel-11121F-ATARM-SAMA5D3-Series-Datasheet_02-Feb-16
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Palmettos have 512MB of memory as opposed to the previously thought
256MB. Update the device trees accordingly.
We run the uart at 115200.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
When used as a BMC, the host expects to be able to use 16MB of
framebuffer memory at the top of RAM.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The pin controller's child nodes expose the functions currently
implemented in the g5 pin controller driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The pin controller's child nodes expose the functions currently
implemented in the the g4 pin controller driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This patch include auxiliary clock definition (clocks which are not derived
from system clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds an external I2S clock in the DT.
The I2S clock could be derived from an external I2S clock or by I2S pll.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Enable analog to digital converter on stm32f429i-eval board.
It has on-board potentimeter wired to ADC3 in8 analog pin and
uses fixed regulator to provide reference voltage.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds USART3 pin configuration on PB10/PA11 pins
for STM32F469I-DISCO board.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch fix memory size to support 16MB of external SDRAM.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Enable VPIF for video captpure and configure input channel 0, used for
composite input.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable VPIF node for video capture, and configure ports. EVM board
uses channel 0 for composite input and channel 1 S-Video input.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add VPIF node and pins to da850 SoC. VPIF has two input channels which
can be described using the standard DT ports and endpoints.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: drop stray newline, typo fixes in commit message]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add .dts file for rev. C of the board by factoring out commonalities
into a shared include file (vf610-zii-dev-rev-b-c.dtsi) and deriving
revision specific file from it (vf610-zii-dev-rev-b.dts and
vf610-zii-dev-reb-c.dts).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: cphealy@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove pwm0grp since it is:
a) Not referenced anywhere in the DTS file (unlike Tower board it
is based on, this board does not use/expose FTM0)
b) Configures PTB2 and PTB3 in a way that contradicts
pinctrl-mdio-mux
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: cphealy@gmail.com
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use common board file and support SATA interface additionally.
Specify the dtb file for i.MX6 build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Common savageboard DT file is used for board support.
Add the vendor name and specify the dtb file for i.MX6Q build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Memory
memblock for DDR3 1GB
* Regulator
3.3V for panel and backlight.
* Display
Enable HDMI and LVDS panel. Savageboard supports AVIC TM097TDH02 panel
which is compatible with Hannstar HSD100PXN1, so reuse it.
* Clock
The commit d28be499c4 ("ARM: dts: imx6qdl-sabresd: Allow HDMI and
LVDS to work simultaneously") is applied to support LVDS and HDMI output
at the same time.
* Pinmux
Support eMMC, ethernet, gpio key for power button, I2C, PWM, SD card
and UART.
* Others
Enable ethernet, UART1 debug, USB host, USDHC3 for microSD card and
USDHC4 for built-in eMMC storage.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Here is a list of patches that converts the current DT to the generic pin
control and muxing properties, now that the pinctrl driver supports it.
-----BEGIN PGP SIGNATURE-----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=6W12
-----END PGP SIGNATURE-----
Merge tag 'sunxi-generic-pinconf-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner conversion to generic pin muxing properties
Here is a list of patches that converts the current DT to the generic pin
control and muxing properties, now that the pinctrl driver supports it.
* tag 'sunxi-generic-pinconf-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Convert pinctrl nodes to generic bindings
ARM: sunxi: Remove useless allwinner,pull property
ARM: sunxi: Remove useless allwinner,drive property
Signed-off-by: Olof Johansson <olof@lixom.net>
- Replace reset and clock magic numbers for OX820 and OX810SE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yu88
-----END PGP SIGNATURE-----
Merge tag 'oxnas-arm-soc-dt-for-4.11' of https://github.com/OXNAS/linux into next/dt
- Add dt-bindings includes for OX820 and OX810SE dtsi
- Replace reset and clock magic numbers for OX820 and OX810SE
* tag 'oxnas-arm-soc-dt-for-4.11' of https://github.com/OXNAS/linux:
ARM: dts: OX820: Update with dt-bindings includes
ARM: dts: OX810: Update with dt-bindings includes
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add da9063 PMIC device node for system restart to gose board
* Add device node for PRR to SoCs where it was missing
* Move RST node before SYSC node where it was incorrectly placed
* Use Gen 2 fallback bindings for I2C, IIC, MSIOf and USB2 phy
* Use SoC-specific compat string for MMCIF where it was missing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=p9k9
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.11
* Add da9063 PMIC device node for system restart to gose board
* Add device node for PRR to SoCs where it was missing
* Move RST node before SYSC node where it was incorrectly placed
* Use Gen 2 fallback bindings for I2C, IIC, MSIOf and USB2 phy
* Use SoC-specific compat string for MMCIF where it was missing
* tag 'renesas-dt-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (25 commits)
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for msiof nodes
ARM: dts: r8a7792: Use R-Car Gen 2 fallback binding for msiof nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for msiof nodes
ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for iic nodes
ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for iic nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for iic nodes
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for iic nodes
ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes
ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes
ARM: dts: r8a7792: Use R-Car Gen 2 fallback binding for i2c nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes
ARM: dts: r8a7778: Use R-Car Gen 1 fallback binding for i2c nodes
ARM: dts: r8a7779: Use R-Car Gen 1 fallback binding for i2c nodes
ARM: dts: r8a7794: Use renesas,rcar-gen2-usb-phy fallback binding
ARM: dts: r8a7791: Use renesas,rcar-gen2-usb-phy fallback binding
ARM: dts: r8a7790: Use renesas,rcar-gen2-usb-phy fallback binding
ARM: dts: gose: Add da9063 PMIC device node for system restart
ARM: dts: sh73a0: Use SoC-specific compat string for mmcif
ARM: dts: r8a7778: Use SoC-specific compat string for mmcif
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Tree-wide replacement was done by commit 2ef7d5f342 ("ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), then the 2nd
round by commit 15b7cc78f0 ("arm64: dts: drop "arm,amba-bus" in
favor of "simple-bus" part 2").
Here, some new users have appeared for Linux v4.10-rc1. Eliminate
them now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On imx53-qsb the TVE DAC regulator comes from:
- LDO7 on the board with the Dialog DA9052 PMIC
- VDAC on the board with the MC34708 PMIC
Pass them in the 'dac-supply' node.
While at it, remove the 'regulator-always-on/regulator-boot-on'
properties as the TVE driver will properly handle it.
Tested on a imx53-qsb board with a Dialog DA9052 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the codec is probed first, the pinctrl node should be
under the codec node.
The codec init was working for this board since U-Boot was
already setting GPIO_0 as CLKO1 but better fix it anyway.
Fixes: 3faa1bb2e8 ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)
The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.
Fixes: b32e700256 ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch provides support for Liebherr's Monitor 6 board (abverrated as
mccmon6) to Linux kernel.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The license text has been mangled at some point then copy pasted across
multiple files. Restore it to what it should be.
Note that this is not intended as a license change.
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DryIce block on i.MX25 chipset uses two interrupts: A normal and a
security violation interrupt. Add the security violation interrupt to
the list, it is optional.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Even if no_bd_ram property is described in TI CPSW bindings the support for
it has never been introduced in CPSW driver, so there are no real users of
it. Hence, remove no_bd_ram property from documentation and DT files.
Cc: 'Rob Herring <robh+dt@kernel.org>'
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Keystone 2 boot monitor uses 32 KB of the MSM RAM @ 0x0c0f7000
on 66AK2G SoCs, so add a reserved child node for the same.
This address is aligned to the values used within the latest boot
monitor firmware [1] as of commit cf8b431e8b3b ("soc: Move load
address to end of MSMC").
[1] git://git.ti.com/processor-firmware/ks2-boot-monitor.git
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Keystone 2 boot monitor uses 32 KB of the MSM RAM @ 0x0c1f0000
on 66AK2E SoCs, so add a reserved child node for the same.
This address is aligned to the values used within the latest boot
monitor firmware [1] as of commit cf8b431e8b3b ("soc: Move load
address to end of MSMC").
[1] git://git.ti.com/processor-firmware/ks2-boot-monitor.git
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Keystone 2 boot monitor uses 32 KB of the MSM RAM @ 0x0c1f8000
on 66AK2L SoCs, so add a reserved child node for the same.
This address is aligned to the values used within the latest boot
monitor firmware [1] as of commit cf8b431e8b3b ("soc: Move load
address to end of MSMC").
[1] git://git.ti.com/processor-firmware/ks2-boot-monitor.git
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Keystone 2 boot monitor uses 32 KB of the MSM RAM @ 0x0c5f0000
on 66AK2H SoCs, so add a reserved child node for the same.
This address is aligned to the values used within the latest boot
monitor firmware [1] as of commit cf8b431e8b3b ("soc: Move load
address to end of MSMC").
[1] git://git.ti.com/processor-firmware/ks2-boot-monitor.git
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add the RAM managed by the Multicore Shared Memory Controller (MSMC)
as a mmio-sram node. The 66AK2G SoCs have 1 MB of such memory. Any
specific MSM memory range needed by a software module ought to be
reserved using an appropriate child node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
