Meaning of ThermSenseCoreSel bit was inverted beginning with K8 RevF.
That means with current driver temp1/temp2 belong to core 1 and
temp3/temp4 belong to core 0 on a K8 RevF/RevG CPU.
This patch ensures that temp1/temp2 always belong to core 0 and
temp3/temp4 to core 1 for all K8 revisions.
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add warning about wrong CPU temperature readouts on all fam F rev F.
The allowed combinations of processors ensure that all processors
in a multisocket system have similar characteristics, e.g.
(1) provide temperature sensor interface (>=RevC && <RevF)
(2) are affected by erratum #141 (>=RevF)
Thus it is sufficient to check the revision of the boot CPU.
For "mixed silicon support" refer to
"Revision Guide for AMD Athlon 64 and AMD Opteron Processors" (RevA-E) and
"Revision Guide for AMD NPT Family 0Fh Processors" (RefF-G).
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sensor can be accessed via various buses. In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported). Separate this latest platform from the core of the sensor
driver to allow support for the other bus type. The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (29 commits)
hwmon: Fix various typos
hwmon: Check for ACPI resource conflicts
hwmon: (lm70) Add TI TMP121 support
hwmon: (lm70) Code streamlining and cleanup
hwmon: Deprecate the fscher and fscpos drivers
hwmon: (fschmd) Add watchdog support
hwmon: (fschmd) Cleanups for watchdog support
hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets
hwmon: (it87) Add support for the ITE IT8720F
hwmon: Don't overuse I2C_CLIENT_MODULE_PARM
hwmon: Add LTC4245 driver
hwmon: (f71882fg) Fix fan_to/from_reg prototypes
hwmon: (f71882fg) Printout fan modes
hwmon: (f71882fg) Add documentation
hwmon: (f71882fg) Fix auto_channels_temp temp numbering with f8000
hwmon: (f71882fg) Add missing pwm3 attr for f71862fg
hwmon: (f71882fg) Add F8000 support
hwmon: (f71882fg) Remove the fan_mode module option
hwmon: (f71882fg) Separate max and crit alarm and beep
hwmon: (f71882fg) Check for hwmon powerdown state
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.
I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
pretty much mean that they conflict on all systems, and we would know
by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
on old designs were ACPI either wasn't supported or didn't deal with
thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
the checks are already done where they belong, i.e. in the bus drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution. This patch extends the
LM70 driver to support the TMP121. The TMP123 differs in pin assign-
ment.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups in preparation of adding watchdog support,
mostly removing _MASK postfix from defines which are not masks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that we cannot create a pci_driver in this driver because PCI will
not call this module's probe function if the i5000-edac driver is already
loaded. That said, we only want one value (AMBASE) from the PCI config space.
Neither driver alters this value, so it's safe to read it. However, we still
want the module aliases, so provide that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C_CLIENT_MODULE_PARM is overkill for force_subclients. We really
only use 4 out of the 48 slots, so we're better defining a custom
variable instead. This change saves 92 bytes of data for each of the
five drivers affected.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The RPM after conversion from / before conversion to a register value can be
much more than 65535 (up to 1500000), so putting this into an u16 can cause
overflows. This changes the functions to use an int to store / get RPM instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Print the mode (duty-cycle or RPM) of each fan on driver load.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Adjust auto_channels_temp show and store functions for different numbering of
temps between f8000 and other supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
For some reason the fan_attr array for the f71862fg was missing the attr for
the 3th pwm output. This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
And (finally) the patch actually adding f8000 support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the fan_mode module option it was a monstrosity to begin with, and
when adding support for the F8000 it becomes a real pain!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While studying the datasheets for adding F8000 support, I noticed that the
F718x2 has separate alarms (and beep control) for its max and crit limits.
We keep the temp#_alarm attributes as they are, even though it would be more
logical to rename them to temp#_max_alarm. Because lm_sensors v2 depends
on them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More F8000 prep work. Take over the checking if the hwmon part is not
powered down from the standalone f8000 driver.
This check is valid for all supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Simplify fan and temp hyst. handling by treating the registers as an array of
nibbles instead of using switch cases. Also unify the way hysts are handled
between temp and fans, the temp code was storing the actual per temp hyst
values in 4 u8's, where as the fan code was storing actual register values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on adding F8000 support I noticed that various of the
store sysfs functions (and a few of the show also) had issues.
This patch fixes the following issues in these functions:
* store: storing the result of strto[u]l in an int, resulting in a possible
overflow before boundary checking
* store: use of f71882fg_update_device(), we don't want to read the whole
device in store functions, just the registers we need
* store: use of cached register values instead of reading the needed regs
in the store function, including cases where f71882fg_update_device() was
not used, this could cause real isues
* show: shown value is a calculation of 2 or more cached register reads,
without locking the data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch is a preparation patch for adding F8000 support to the f71882fg
driver. If you look at the register addresses and esp, the bits used for
the temperature channels, then you will notice that it appears that they
start at 1 in a system meant to start at 0. As the F8000 actually uses the 0
addresses and bits, this patch changes the f71882fg driver to take 4
temperatures numbered 0-3 in to account, using 1-3 in this new scheme for
the temperatures actually present in the F718x2FG.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The f71882fg driver did some io to ioports it hadn't reserved yet in its
find (detect) function, this patches moves this io to the probe function
where these ports are reserved and this io belongs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the Fintek f71862fg superio monitoring
functions to the f71882fg driver.
This support has been tested without problems on a Jetway J9F2 by
Tony McConnell.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups as preparation for adding f71862fg support to the
f71882fg driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM (fan speed control) support to the f71882fg driver. Both
manual control and automatic (temperature-based) modes are supported.
Additionally, each mode has a PWM-based and an RPM-based variant. By
default we use the mode set by the BIOS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A few cleanups that were originally part of a larger patch but are
better submitted separately.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert f71882fg driver from SENSOR_ATTR to SENSOR_ATTR2 use, this is a
preparation patch for adding pwm support, which is broken out to make what
changes really in the pwm support patch clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add temperature sensor support for MacBook Air 2.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated. This in turn happens only when
someone tells the chip to read its temperature sensors. Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7470 driver currently assumes that 1s is the proper time to wait to
read all temperature sensors. However, the correct time is 200ms *
number_of_sensors. This patch sets the default time to provide for 10
sensors and then lowers it based on the number of sensor inputs that have
nozero values.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the small window that it takes to read the temperature sensors, the pwm
outputs momentarily drop to 0. This causes a noticeable hiccup in fan
speed, which is slightly annoying. The solution is to manually program
the pwm output with whatever the automatic value is and then shift the
fans to manual control while reading temperatures. Once that is done, put
the fans back to whatever mode of control was there before.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify some hwmon drivers to use DIV_ROUND_CLOSEST instead of bloating
source with (naughty) macros.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to analyze the SMC of the newer MacPros, applesmc needs to
recognize the machine. This patch adds the missing generic dmi_match
entry for MacPro models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 6.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Caleb Hyde <caleb.hyde@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/hwmon/lis3lv02d.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New driver to play with. As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors. This driver has been tested on an IntelliStation Z30.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard"). It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.
This driver was first written by Yan Burman. Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now). Pavel Machek removed few more features and switched locking from
semaphore to mutex.
Several people have contributed to the database of the axes.
[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7468 is a follow-on to the adt7463, so plumb in adt7468 support
along the same code paths.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.
This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash. Make this assumption hold true for these
three drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerometer and temperature sensor support for Macbook 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 8.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Klaus Doblmann <klaus.doblmann@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook Pro 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Ricky Campbell <johnrcampbell@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The read fail ratio is sensitive to the delay between the first byte
written and the first byte read; apparently the sensors cannot be rushed.
Increasing the minimum wait time, without changing the total wait time,
improves the fail ratio from a 8% chance that any of the sensors fails in
one read, down to 0.4%, on a Macbook Air. On a Macbook Pro 3,1, the
effect is even more apparent. By reducing the number of status polls, the
ratio is further improved to below 0.1%. Finally, increasing the total
wait time brings the fail ratio down to virtually zero.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Bob McElrath <bob@mcelrath.org>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for Macbook Pro 3.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temperature sensor support for the Macbook Pro 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmi_system_id.driver_data is already void*.
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerometer, backlight and temperature sensor support
for the Macbook Air.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some recent Macbooks, the package length for the light sensors ALV0 and
ALV1 has changed from 6 to 10. This patch allows for a variable package
length encompassing both variants.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time to wait for a status change while reading or writing to the SMC
ports is a balance between read reliability and system performance. The
current setting yields rougly three errors in a thousand when
simultaneously reading three different temperature values on a Macbook
Air. This patch increases the setting to a value yielding roughly one
error in ten thousand, with no noticable system performance degradation.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On many Macbooks since mid 2007, the Pro, C2D and Air models, applesmc
fails to read some or all SMC ports. This problem has various effects,
such as flooded logfiles, malfunctioning temperature sensors,
accelerometers failing to initialize, and difficulties getting backlight
functionality to work properly.
The root of the problem seems to be the command protocol. The current
code sends out a command byte, then repeatedly polls for an ack before
continuing to send or recieve data. From experiments leading to this
patch, it seems the command protocol never quite worked or changed so that
one now sends a command byte, waits a little bit, polls for an ack, and if
it fails, repeats the whole thing by sending the command byte again.
This patch implements a send_command function according to the new
interpretation of the protocol, and should work also for earlier models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At one single place in the code, the specified number of bytes to read and
the actual number of bytes read differ by one. This one-liner patch fixes
that inconsistency.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds therm-min/max/crit-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the therm_group (of sysfs files)
The thermistors use voltage channels to measure; so they don't have a
fault-alarm, but unlike the other voltages, they do have an overtemp,
which we call crit (by convention).
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
temp and vin status register values may be set by chip specifications, set
again by bios, or by this previously loaded driver. Debug output nicely
displays modprobe init=\d actions.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver handles 3 logical devices in fixed length array. Give this a
define-d constant.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temp-min/max/crit/fault-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the temp_group (of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds vin-min/max-alarm callbacks, sensor-device-attribute declarations,
and refs to those new decls in the macro used to initialize the vin_group
(of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring hwmon/pc87360 into agreement with
Documentation/hwmon/sysfs-interface.
Patchset adds separate limit alarms for voltages and temps, it also adds
temp[123]_fault files. On my Soekris, temps 1,2 are unused/unconnected,
so temp[123]_fault = 1,1,0 respectively. This agrees with
/usr/bin/sensors, which has always shown them as OPEN. Temps 4,5,6 are
thermistor based, and dont have a fault bit in their status register.
This patch:
2 different kinds of constants added:
- CHAN_ALM_* constants for (later) vin, temp alarm callbacks.
- CHAN_* conversion constants, used in _init_device, partly for RW1C bits
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.
[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.
One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This means that if we have to start the monitor when probed, we also
stop it on removal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register. The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.
Fix the condition and also ensure we never set the Initialization bit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The encoding of temperatures varies between chips and modes. So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros. This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times. This change should not affect functionality.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
The new-style dme1737 driver implements the optional detect() callback
to cover the use cases of the legacy driver. I don't actually expect
any new-style device for that driver, but as the old i2c API is going
away soon, we have to switch to the new one.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
The dme1737 driver support both LPC (ISA) and SMBus devices. At the
moment it's rather i2c-centric, and LPC variants use a fake i2c_client
for some operations.
In a near future, i2c_client will be allocated by i2c-core rather than
by the device drivers, so non-i2c drivers will not have one. As a
preparation step, change the driver code to no longer assume that
an i2c_client structure is always available. No functional change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Daniel Exner <dex@dragonslave.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.
Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes the needlessly global ad7414_update_device() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Tested-by: John Gumb <john.gumb@tandberg.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The atxp1 device detection code has a major logic flaw, fix it. Not
sure how we managed to miss this when the driver was merged...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Sebastian Witt <se.witt@gmx.net>
This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all AMD K8 have 6 VID pins, contrary to what was assumed in
commit 116d0486bd. This commit broke
support of older CPU models which have only 5 VID pins:
http://bugzilla.kernel.org/show_bug.cgi?id=11329
We need two entries in the hwmon-vid table, one for 5-bit VID models
(K8 revision <= E) and one for 6-bit VID models (K8 revision >= F).
This fixes bug #11329.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add in the CPUID for Nehalem chips.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all sensors are read when the energy meter is queried via
sysfs. This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use. Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On older machines, probing for a nonexistent AEM interface returned an
IPMI error; when we saw this, we'd stop probing. On the x3650 M2 and
(presumably) later, we are returned a value indicating success and a
buffer full of garbage or zeroes. This causes the probe function to run
in an infinite loop. To fix this, we add one last check--if the
interface number we're looking for is higher than the number of
interfaces that AEM claims to have, stop probing.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously the driver was only using DMI to prevent smbus probing on
non-Abit motherboards. However, since the manual probing method is
brittle and prone to failure on some Abit motherboards (esp. the Abit
IP35 Pro) it is better to use DMI to also read the board name and then
decide whether or not to probe the bus.
At the moment, we do not have a list of valid DMI name strings to use
for existing and supported motherboards. This patch only implements DMI
probing for the IP35 Pro. For motherboards that can not yet use DMI
probing, a warning will be printed to the kernel log asking those users
to email me their dmidecode output.
The existing manual probing mechanism will be used if CONFIG_DMI is not
enabled, if DMI probing fails (for DMI-unsupported motherboards), or if
DMI probing fails and the "force" option is set (for DMI-supported
motherboards). Ideally in the longer term this manual probing method
would be removed.
This patch should be safe to apply as it does not change the probing
behaviour for most of the supported motherboards, just the IP35 Pro,
which already has regressions filed against it in 2.6.26.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11212
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the sensor -> channel/dimm mapping in tempX_label.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...
Code for 8 channels by Tobias Himmer.
This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
