After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/intel/igc/igc_mac.c:424 igc_check_for_copper_link()
error: uninitialized symbol 'link'.
This patch come to fix this warning and initialize the 'link' symbol.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 707abf0695 ("igc: Add initial LTR support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
collision_delta, tx_packet_delta, txcw, adaptive_ifs and
has_fwsm fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
LED control currently not implemented.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The statistics of this register are being tracked, however, the register
was inadvertently missed when implementing igc_clear_hw_cntrs_base().
The register is clear on read, so add it to the function so that the
register is cleared when requested so the tracked count is accurate.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Straightforward conversion to new infra. Driver restores info
after close/open cycle by calling its internal restore function
so just use that, no need for udp_tunnel_nic_reset_ntf() here.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of new common udp_tunnel_nic infra. ixgbe supports
IPv4 only, and only single VxLAN and Geneve ports (one each).
v2:
- split out the RXCSUM feature handling to separate change;
- declare structs separately;
- use ti.type instead of assuming table 0 is VxLAN;
- move setting netdev->udp_tunnel_nic_info to its own switch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears the clearing of UDP tunnel ports when RXCSUM
is disabled is unnecessary. Driver will not pay attention
to checksum bits if RXCSUM is not set, so we can let
the hardware parse the packets.
Note that the UDP tunnel port NDO handlers don't pay attention
to the state of RXCSUM, so the ports could had been re-programmed,
anyway.
This cleanup simplifies later conversion patch.
v2:
- break this out of the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/20200702162651.49526-3-luc.vanoostenryck@gmail.comhttps://lore.kernel.org/r/20200702162651.49526-4-luc.vanoostenryck@gmail.com]
Link: https://lore.kernel.org/r/20200702162651.49526-2-luc.vanoostenryck@gmail.com
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-07-01
This series contains updates to all Intel drivers, but a majority of the
changes are to the i40e driver.
Jeff converts 'fall through' comments to the 'fallthrough;' keyword for
all Intel drivers. Removed unnecessary delay in the ixgbe ethtool
diagnostics test.
Arkadiusz implements Total Port Shutdown for i40e. This is the revised
patch based on Jakub's feedback from an earlier submission of this
patch, where additional code comments and description was needed to
describe the functionality.
Wei Yongjun fixes return error code for iavf_init_get_resources().
Magnus optimizes XDP code in i40e; starting with AF_XDP zero-copy
transmit completion path. Then by only executing a division when
necessary in the napi_poll data path. Move the check for transmit ring
full outside the send loop to increase performance.
Ciara add XDP ring statistics to i40e and the ability to dump these
statistics and descriptors.
Tony fixes reporting iavf statistics.
Radoslaw adds support for 2.5 and 5 Gbps by implementing the newer ethtool
ksettings API in ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Added full support for new version Ethtool API. New API allow use
2500Gbase-T and 5000base-T supported and advertised link speed modes.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a 4 seconds delay in ixgbe_diag_test() that is holding up other
ioctls such as SIOCGIFCONF that Oracle database applications use.
One of Oracle's product runs "ethtool -t ethX online" periodically for
system monitoring and that is impacting database applications that use
SIOCGIFCONF at that same time.
This 4 second delay was needed in out early 1GbE parts to give the PHY
time to recover from a reset. This code was carried forward to the 10 GbE
driver even it was not needed for the supported PHYs in the ixgbe driver.
CC: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
CC: Jack Vogel <jack.vogel@oracle.com>
Reported-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit bac8486116 ("iavf: Refactor the watchdog state machine") inverted
the logic for when to update statistics. Statistics should be updated when
no other commands are pending, instead they were only requested when a
command was processed. iavf_request_stats() would see a pending request
and not request statistics to be updated. This caused statistics to never
be updated; fix the logic.
Fixes: bac8486116 ("iavf: Refactor the watchdog state machine")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Interfaces already exist for dumping Rx and Tx descriptor information.
Introduce another for doing the same for XDP descriptors.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prior to this, only the Rx and Tx ring statistics were dumped. The XDP
ring statistics are now dumped as well.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prior to this, only Rx and Tx ring statistics were accounted for.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move the check if the HW Tx ring is full to outside the send
loop. Currently it is checked for every single descriptor that we
send. Instead, tell the send loop to only process a maximum number of
packets equal to the number of available slots in the Tx ring. This
way, we can remove the check inside the send loop to and gain some
performance.
Suggested-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Eliminate a division in the napi_poll data path. This division is
executed even though it is only needed in the rare case when there are
not enough interrupt lines so they have to be shared between queue
pairs. Instead, just test for this case and only execute the division
if needed. The code has been lifted from the ice driver.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Improve the performance of the AF_XDP zero-copy Tx completion
path. When there are no XDP buffers being sent using XDP_TX or
XDP_REDIRECT, we do not have go through the SW ring to clean up any
entries since the AF_XDP path does not use these. In these cases, just
fast forward the next-to-use counter and skip going through the SW
ring. The limit on the maximum number of entries to complete is also
removed since the algorithm is now O(1). To simplify the code path, the
maximum number of entries to complete for the XDP path is therefore
also increased from 256 to 512 (the default number of Tx HW
descriptors). This should be fine since the completion in the XDP path
is faster than in the SKB path that has 256 as the maximum number.
This patch provides around 4% throughput improvement for the l2fwd
application in xdpsock on my machine.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: b66c7bc1cd ("iavf: Refactor init state machine")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After OS requests to down a link on a physical network port, the
traffic is no longer being processed but the physical link with
a link partner is still established.
Currently there is a feature (Link down on close) which allows
to physically bring the link down (after OS request).
With this patch new feature with similar capability is introduced:
TOTAL_PORT_SHUTDOWN
Allows to physically disable the link on the NIC's port.
If enabled, (after link down request from the OS)
no link, traffic or led activity is possible on that port.
If I40E_FLAG_TOTAL_PORT_SHUTDOWN is enabled, the
I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED must be explicitly forced to
true and cannot be disabled at that time.
The functionalities are exclusive in terms of configuration, but
they also have similar behavior (allowing to disable physical link
of the port), with following differences:
- LINK_DOWN_ON_CLOSE_ENABLED is configurable at host OS run-time
and is supported by whole family of 7xx Intel Ethernet Controllers
- TOTAL_PORT_SHUTDOWN may be enabled only before OS loads (in BIOS)
only if motherboard's BIOS and NIC's FW has support of it
- when LINK_DOWN_ON_CLOSE_ENABLED is used, the link is being brought
down by sending phy_type=0 to NIC's FW
- when TOTAL_PORT_SHUTDOWN is used, phy_type is not altered, instead
the link is being brought down by clearing bit
(I40E_AQ_PHY_ENABLE_LINK) in abilities field of
i40e_aq_set_phy_config structure
Introduced changes:
- new private flag I40E_FLAG_TOTAL_PORT_SHUTDOWN for handling the
feature
- probe of NVM if the feature was enabled at driver's port
initialization
- special handling on link-down procedure to let FW physically
shutdown the port if the feature was enabled
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The idea behind devres is that the release callbacks are called if
probe fails. As we now check the return value of ixgbe_mii_bus_init(),
we can drop the call devm_mdiobus_free() in error path as the release
callback will be called automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function may fail. Check its return value and propagate the error
code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i225 device support only copper mode.
There is no point to check media type in the
igc_config_fc_after_link_up() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PHY of the i225 device support only copper mode.
There is no point to check media type in the
igc_power_up_link() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the implementation of igc_power_down_link()
method was just calling igc_power_down_phy_copper_base()
method.
We can just call igc_power_down_phy_copper_base()
method directly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TCP segmentation TX context fail counter is not
applicable for i225 devices.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown<aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add EEE TX LPI and EEE RX LPI counters. A EEE TX LPI event
occurs when the transmitter enters EEE (IEEE 802.3az) LPI
state. A EEE RX LPI event occurs when the receiver detect
link partner entry into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When Rx timestamping is enabled, we set the timestamp bit in SRRCTL
register for each queue, but we don't clear it when disabling. This
patch fixes igc_ptp_disable_rx_timestamp() accordingly.
Also, this patch gets rid of igc_ptp_enable_tstamp_rxqueue() and
igc_ptp_enable_tstamp_all_rxqueues() and move their logic into
igc_ptp_enable_rx_timestamp() to keep the enable and disable
helpers symmetric.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current igc_ptp_set_timestamp_mode() logic is a bit tangled since it
handles many different hardware configurations in one single place,
making it harder to follow. This patch untangles that code by breaking
it into helper functions.
Quick note about the hw->mac.type check which was removed in this
refactoring: this check it not really needed since igc_i225 is the only
type supported by the IGC driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As implemented in igc_ethtool_get_ts_info(), igc only supports HWTSTAMP_
FILTER_ALL so any HWTSTAMP_FILTER_* option the user may set falls back to
HWTSTAMP_FILTER_ALL.
HWTSTAMP_FILTER_ALL is implemented via Rx Time Sync Control (TSYNCRXCTL)
configuration which timestamps all incoming packets. Configuring a
UDP filter, in addition to TSYNCRXCTL, doesn't add much so this patch
removes that code. It also takes this opportunity to remove some
non-applicable comments.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The __IGC_PTP_TX_IN_PROGRESS flag indicates we have a pending Tx
timestamp. In some places, instead of checking that flag, we check
adapter->ptp_tx_skb. This patch fixes those places to use the flag.
Quick note about igc_ptp_tx_hwtstamp() change: when that function is
called, adapter->ptp_tx_skb is expected to be valid always so we
WARN_ON_ONCE() in case it is not.
Quick note about igc_ptp_suspend() change: when suspending, we don't
really need to check if there is a pending timestamp. We can simply
clear it unconditionally.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions igc_ptp_tx_hang() and igc_ptp_tx_work() have duplicate
code which handles Tx timestamp timeouts. This patch does a trivial
refactoring by moving that code to its own function and reusing it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Differently from I210, I225 doesn't report Rx timestamps via the TS bit
Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are
reported in the packet buffer only, which is implemented by igc_ptp_rx_
pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code
related to it, copied from igb driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LTR message on the PCIe inform the requested latency
on which the PCIe must become active to the downstream
PCIe port of the system.
This patch provide recommended LTR parameters by i225
specification.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE802.3az-2010 Energy Efficient Ethernet has been
approved as standard (September 2010) and the driver
can enable and disable it via ethtool.
Disable the feature by default on parts which support it.
Add enable/disable eee options.
tx-lpi, tx-timer and advertise not supported yet.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Organize driver documentation by device type. Most documents
have fairly verbose yet uninformative names, so let users
first select a well defined device type, and then search for
a particular driver.
While at it rename the section from Vendor drivers to
Hardware drivers. This seems more accurate, besides people
sometimes refer to out-of-tree drivers as vendor drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2020-06-25
This series contains updates to i40e driver and removes the individual
driver versions from all of the Intel wired LAN drivers.
Shiraz moves the client header so that it can easily be shared between
the i40e LAN driver and i40iw RDMA driver.
Jesse cleans up the unused defines, since they are just dead weight.
Alek reduces the unreasonably long wait time for a PF reset after reboot
by using jiffies to limit the maximum wait time for the PF reset to
succeed. Added additional logging to let the user know when the driver
transitions into recovery mode. Adds new device support for our 5 Gbps
NICs.
Todd adds a check to see if MFS is set after warm reboot and notifies
the user when MFS is set to anything lower than the default value.
Arkadiusz fixes a possible race condition, where were holding a
spin-lock while in atomic context.
v2: removed code comments that were no longer applicable in patch 2 of
the series. Also removed 'inline' from patch 4 and patch 8 of the
series. Also re-arranged code to be able to remove the forward
function declarations. Dropped patch 9 of the series, while the
author works on cleaning up the commit message.
v3: Updated patch 8 description to answer Jakub's questions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In some occasions task held spinlock (mac_filter_hash_lock),
while being rescheduled due to admin queue mutex_lock. The struct
i40e_spinlock asq_spinlock, which later expands to struct mutex
spinlock. Moved i40e_aq_set_vsi_multicast_promiscuous(),
i40e_aq_set_vsi_unicast_promiscuous(),
i40e_aq_set_vsi_mc_promisc_on_vlan(), and
i40e_aq_set_vsi_uc_promisc_on_vlan() outside of atomic context. Without
this patch there is a race condition, which might result in scheduling
while in atomic context. The race condition is between the thread, which
holds mac_filter_hash_lock, while trying to acquire an admin queue mutex
and a thread, which already has said admin queue mutex. The thread, which
holds spinlock, fails to acquire the mutex, which causes this thread to
sleep.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make possible for the i40e driver to bind to the new v710 for 5GBASE-T
NICs.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
A customer was chain-booting to provision his systems and one of the
steps was setting MFS. MFS isn't cleared by normal warm reboots
(clearing requires a GLOBR) and there was no indication of why Jumbo
Frame receives were failing.
Add a warning if MFS is set to anything lower than the default.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Detect and log information about pre-recovery mode when firmware
transitions to a recovery mode.
When a firmware transitions to a recovery mode it stores a number
of unexpected EMP resets in one of its registers. The number of EMP
resets ranging from 0x21 to 0x2A indicates that FW transitions
to recovery mode. Use these values to emit log entry about transition
process. Previously the pre-recovery mode may not have been detected
and there was no log entry when NIC was in pre-recovery mode.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use jiffies to limit max waiting time for PF reset to succeed.
Previous wait loop was unreliable. It required unreasonably long time
to wait for PF reset after reboot when NIC was about to enter
recovery mode
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove all the unused defines as they are just dead weight.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move i40e_client.h to include/linux/net/intel/*
since its shared between i40iw and i40e.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than requiring every hw crypto capable NIC driver to do a check for
slave_dev being set, set real_dev in the xfrm layer and xso init time, and
then override it in the bonding driver as needed. Then NIC drivers can
always use real_dev, and at the same time, we eliminate the use of a
variable name that probably shouldn't have been used in the first place,
particularly given recent current events.
CC: Boris Pismenny <borisp@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slave devices in a bond doing hardware encryption also need to be aware
that they're slaves, so we operate on the slave instead of the bonding
master to do the actual hardware encryption offload bits.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Acked-by: Jeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the AF_XDP buffer allocator was introduced, the Rx SW ring
"rx_bi" allocation was moved from i40e_setup_rx_descriptors()
function, and was instead done in the i40e_configure_rx_ring()
function.
This broke the ethtool set_ringparam() hook for changing the Rx
descriptor count, which was relying on i40e_setup_rx_descriptors() to
handle the allocation.
Fix this by adding an explicit i40e_alloc_rx_bi() call to
i40e_set_ringparam().
Fixes: be1222b585 ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
READ_ONCE should be used when reading rings prior to accessing the
statistics pointer. Introduce this as well as the corresponding WRITE_ONCE
usage when allocating and freeing the rings, to ensure protected access.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The CONFIG_PM_SLEEP #ifdef checks in this file are inconsistent,
leading to a warning about sometimes unused function:
drivers/net/ethernet/intel/e1000e/netdev.c:137:13: error: unused function 'e1000e_check_me' [-Werror,-Wunused-function]
Rather than adding more #ifdefs, just remove them completely
and mark the PM functions as __maybe_unused to let the compiler
work it out on it own.
Fixes: e086ba2fcc ("e1000e: disable s0ix entry and exit flows for ME systems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let PCI
core handle the work.
e1000_suspend() calls __e1000_shutdown() to perform intermediate tasks.
__e1000_shutdown() modifies the value of "wake" (device should be wakeup
enabled or not), responsible for controlling the flow of legacy PM.
Since, PCI core has no idea about the value of "wake", new code for generic
PM may produce unexpected results. Thus, use "device_set_wakeup_enable()"
to wakeup-enable the device accordingly.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the system will be woken up via WOL(Wake On LAN) even if the
device wakeup ability has been disabled via sysfs:
cat /sys/devices/pci0000:00/0000:00:1f.6/power/wakeup
disabled
The system should not be woken up if the user has explicitly
disabled the wake up ability for this device.
This patch clears the WOL ability of this network device if the
user has disabled the wake up ability in sysfs.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver")
Reported-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
With an increased number of VFs, it's possible to encounter the following
issue during reset.
iavf b8d4:00:02.0: Hardware reset detected
iavf b8d4:00:02.0: Reset never finished (0)
iavf b8d4:00:02.0: Reset task did not complete, VF disabled
Increase the reset complete wait count to allow for 128 VFs to complete
reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 4ae4916b56 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb
speeds") added the ability for the PF to report 2.5 and 5Gb speeds,
however, the iavf driver does not recognize those speeds as the values were
not added there. Add the proper enums and values so that iavf can properly
deal with those speeds.
Fixes: 4ae4916b56 ("i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb speeds")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Witold Fijalkowski <witoldx.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->link_speed has type enum virtchnl_link_speed but our comparisons
are against enum iavf_aq_link_speed. Though they are, currently, the same
values, change the comparison to the matching enum virtchnl_link_speed
since that may not always be the case.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link speeds are communicated over virtchnl using an enum
virtchnl_link_speed. Currently, the highest link speed is 40Gbps which
leaves us unable to reflect some speeds that an ice VF is capable of.
This causes link speed to be misreported on the iavf driver.
Allow for communicating link speeds using Mbps so that the proper speed can
be reported for an ice VF. Moving away from the enum allows us to
communicate future speed changes without requiring a new enum to be added.
In order to support communicating link speeds over virtchnl in Mbps the
following functionality was added:
- Added u32 link_speed_mbps in the iavf_adapter structure.
- Added the macro ADV_LINK_SUPPORT(_a) to determine if the VF
driver supports communicating link speeds in Mbps.
- Added the function iavf_get_vpe_link_status() to fill the
correct link_status in the event_data union based on the
ADV_LINK_SUPPORT(_a) macro.
- Added the function iavf_set_adapter_link_speed_from_vpe()
to determine whether or not to fill the u32 link_speed_mbps or
enum virtchnl_link_speed link_speed field in the iavf_adapter
structure based on the ADV_LINK_SUPPORT(_a) macro.
- Do not free vf_res in iavf_init_get_resources() as vf_res will be
accessed in iavf_get_link_ksettings(); memset to 0 instead. This
memory is subsequently freed in iavf_remove().
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
