Mostly year updates, but one addition as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the i.MX23/28 reference manuals both mmc interfaces support
the MMC_ERASE command. So enable this capability in the driver to allow
erase/discard/trim requests.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case spi_sync_locked fails, the fix reports the error and
returns the error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some controllers, in Present State Register, Data Line
Active bit is not reliable for commands (such as CMD6, CMD7,
CMD12, CMD28, CMD29, or CMD38) with busy signal. DLA affects
Command with Data Inhibit bit. Therefore, software driver
may not know the busy status in DLA/CDIHB.
Futunately MMC core driver has already polled card status
with CMD13 after sending any command with busy signal. So
we can just ignore CDIHB never released issue for such
controllers. This patch is to add a quirk to handle this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invalid Transfer Complete (IRQSTAT[TC]) bit could be set during
multi-write operation even when the BLK_CNT in BLKATTR register
has not reached zero. Therefore, Transfer Complete might be
reported twice due to this erratum since a valid Transfer Complete
occurs when BLK_CNT reaches zero. This erratum is to fix this issue
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the event of that any data error (like, IRQSTAT[DCE]) occurs
during an eSDHC data transaction where DMA is used for data
transfer to/from the system memory, setting the SYSCTL[RSTD]
register may cause a system hang. If software sets the register
SYSCTL[RSTD] to 1 for error recovery while DMA transferring is
not complete, eSDHC may hang the system bus. This happens because
the software register SYSCTL[RSTD] resets the DMA engine without
waiting for the completion of pending system transactions. This
erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add erratum A011334 support in lx2160 2.0 SoC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As mmci_variant_init() is a local function to mmci.c, let's convert it into
static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It's good practice to share functions via header files, rather than from
the c-files. Therefore, let's move sdmmc_variant_init() to mmci.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It seems a bit silly to have a header file to share only the
qcom_variant_init() function. So, let's just drop it and move the
declaration of the function into the common mmci.h instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Having mmci_dmae_start() to invoke the shared function, dml_start_xfer(),
explicitly for the qcom variant isn't very nice. Let's clean up this code
by moving the qcom specific parts into the qcom ->dma_start() callback and
then drop dml_start_xfer() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There's no point clearing the variant flag in case the qcom variant fails
to setup DMA. This is because if mmci_dma_setup() fails, then the use_dma
flag remains set to false, which leads to mmci using PIO mode and not DMA.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Some of the DMA functions are shared via mmci.h, however they are not
implemented unless CONFIG_DMA_ENGINE is set. Therefore, add that constraint
to the header file as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
commit 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback") skips data resets during tuning operation. Because of this,
a data error or data finish interrupt might still arrive after a command
error has been handled and the mrq ended. This ends up with a "mmc0: Got
data interrupt 0x00000002 even though no data operation was in progress"
error message.
Fix this by adding a platform specific callback for sdhci_irq. Mark the
mrq as a failure but wait for a data interrupt instead of calling
finish_mrq().
Fixes: 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The alcor driver is setting up data transfer and submitting the associated
MMC command at the same time. While this works most of the time, it
occasionally causes problems upon write.
In the working case, after setting up the data transfer and submitting
the MMC command, an interrupt comes in a moment later with CMD_END and
WRITE_BUF_RDY bits set. The data transfer then happens without problem.
However, on occasion, the interrupt that arrives at that point only
has WRITE_BUF_RDY set. The hardware notifies that it's ready to write
data, but the associated MMC command is still running. Regardless, the
driver was proceeding to write data immediately, and that would then cause
another interrupt indicating data CRC error, and the write would fail.
Additionally, the transfer setup function alcor_trigger_data_transfer()
was being called 3 times for each write operation, which was confusing
and may be contributing to this issue.
Solve this by tweaking the driver behaviour to follow the sequence observed
in the original ampe_stor vendor driver:
1. When starting request handling, write 0 to DATA_XFER_CTRL
2. Submit the command
3. Wait for CMD_END interrupt and then trigger data transfer
4. For the PIO case, trigger the next step of the data transfer only
upon the following DATA_END interrupt, which occurs after the block has
been written.
I confirmed that the read path still works (DMA & PIO) and also now
presents more consistency with the operations performed by ampe_stor.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15 ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting max_blk_count to 1 here was causing the mmc block layer
to always use the MMC_READ_SINGLE_BLOCK command here, which the
driver does not DMA-accelerate.
Drop the max_blk_ settings here. The mmc host defaults suffice,
along with the max_segs and max_seg_size settings, which I have
now documented in more detail.
Now each MMC command reads 4 512-byte blocks, using DMA instead of
PIO. On my SD card, this increases read performance (measured with dd)
from 167kb/sec to 4.6mb/sec.
Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 6d5cd068ee ("mmc: sdhci: use WP GPIO in
sdhci_check_ro()") and commit 39ee32ce48 ("mmc: sdhci-omap: drop
->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE
to check if the card is read-only, if wp-gpios is not populated
in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have
correct read-only state.
sdhci-omap can be used by platforms with both micro SD slot and standard
SD slot with physical write protect pin (using GPIO). Set caps2 to
MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or
not.
This fix is required since existing device-tree node doesn't have
"disable-wp" property and to preserve old-dt compatibility.
Fixes: 6d5cd068ee ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Fixes: 39ee32ce48 ("mmc: sdhci-omap: drop ->get_ro() implementation")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Building with clang finds a mistaken __init tag:
WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host()
The function davinci_mmcsd_probe() references
the function __init init_mmcsd_host().
This is often because davinci_mmcsd_probe lacks a __init
annotation or the annotation of init_mmcsd_host is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clang points out several instances of mismatched types in this drivers,
all coming from a single declaration:
drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to
different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion]
direction = DMA_DEV_TO_MEM;
~ ^~~~~~~~~~~~~~
drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to
different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion]
tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
The behavior is correct, so this must be a simply typo from
dma_data_direction and dma_transfer_direction being similarly named
types with a similar purpose.
Fixes: 6464b71409 ("mmc: pxamci: switch over to dmaengine use")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
The original purpose of the code I fix is to replace max_discard with
max_trim if max_trim is less than max_discard. When max_discard is 0
we should replace max_discard with max_trim as well, because
max_discard equals 0 happens only when the max_do_calc_max_discard
process is overflowed, so if mmc_can_trim(card) is true, max_discard
should be replaced by an available max_trim.
However, in the original code, there are two lines of code interfere
the right process.
1) if (max_discard && mmc_can_trim(card))
when max_discard is 0, it skips the process checking if max_discard
needs to be replaced with max_trim.
2) if (max_trim < max_discard)
the condition is false when max_discard is 0. it also skips the process
that replaces max_discard with max_trim, in fact, we should replace the
0-valued max_discard with max_trim.
Signed-off-by: Jiong Wu <Lohengrin1024@gmail.com>
Fixes: b305882fbc (mmc: core: optimize mmc_calc_max_discard)
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card was removed in suspended state and a new one was inserted,
print a debug log when the check detects that it's not the old card.
Signed-off-by: hongjiefang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 72a5af554d ("mmc: core: Add support for handling CQE requests")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user of mmc_align_data_size() is sdio_align_size(), which is
called from SDIO func drivers to let them distinguish, how to optimally
allocate data buffers.
Let's move mmc_align_data_size() close to the SDIO code as to make it
static, rename it to _sdio_align_size() and simplify its definition, all
with the purpose of clarifying that this is SDIO specific.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
The call tree looks something like this:
mmc_spi_probe
mmc_add_host
mmc_start_host
_mmc_detect_change
mmc_schedule_delayed_work(&host->detect, 0)
mmc_rescan
host->bus_ops->detect(host)
mmc_detect
_mmc_detect_card_removed
host->ops->get_cd(host)
mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set)
mmc_gpiod_request_cd
ctx->cd_gpio = desc
To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ
is registered.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC OF parsing functions, which parses various host DT properties, should
stay close to each other. Therefore, let's move mmc_of_parse_voltage()
close to mmc_of_parse() into host.c.
Additionally, there is no reason to build the code only when CONFIG_OF is
set, as there should be stub functions for the OF helpers that is being
used, so let's drop this condition as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only left user of mmc_regulator_get_ocrmask() is the mmc core itself.
Therefore, let's drop the export and turn it into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc regulator helper functions, are placed in the extensive core.c
file. In a step towards trying to create a better structure of files,
avoiding too many lines of code per file, let's move these helpers to a new
file, regulator.c.
Moreover, this within this context it makes sense to also drop the export
of mmc_vddrange_to_ocrmask(), but instead let's make it internal to the mmc
core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the open-coding of the parsing of the "voltage-ranges" DT
property and convert to use the common mmc_of_parse_voltage() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All callers of mmc_wait_for_app_cmd() set the retries in-parameter to
MMC_CMD_RETRIES. This is silly, so let's just drop the in-parameter
altogether, as to simplify the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_wait_for_app_cmd() is an internal function for sd_ops.c, thus let's
drop the unnecessary export and turn it into static function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SCC is used for SDR104/HS200/HS400. We need to change SCC_DT2FF
according to the mode. If it is inappropriate, CRC error tends to occur.
This adds variable "tap_hs400" for HS400 mode and configures SCC_DT2FF
as needed.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased to upstream and updated commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
according to what the compiler looks for, where we are expecting to fall
through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI core is know properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-tegra code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI core is now properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-omap code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though SDHCI controllers may have a dedicated WP pin that can be
queried using the SDHCI_PRESENT_STATE register, some platforms may
chose to use a separate regular GPIO to route the WP signal. Such a
GPIO is typically represented using the wp-gpios property in the
Device Tree.
Unfortunately, the current sdhci_check_ro() function does not make use
of such GPIO when available: it either uses a host controller specific
->get_ro() operation, or uses the SDHCI_PRESENT_STATE. Several host
controller specific ->get_ro() functions are implemented just to check
a WP GPIO state.
Instead of pushing this to more controller-specific implementations,
let's handle this in the core SDHCI code, just like it is already done
for the CD GPIO in sdhci_get_cd().
The below patch simply changes sdhci_check_ro() to use the value of
the WP GPIO if available.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The WMT SDMMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> so drop this surplus include.
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Sunxi MMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: cenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI PXAv2 driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> so drop this surplus include.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI BCM Kona driver uses slot GPIO helpers and does not
make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MXS-MMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MXCMMC driver uses slot GPIO helpers and does not make
any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these
surplus includes.
Cc: Jun Qian <hangdianqj@163.com>
Cc: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is an if block that is not indented, fix this. Also add a
break statement on the default case to clean up a cppcheck warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD specs version 4.x and 5.x have a dedicated slices in the SCR register.
Higher versions will rely on a combination of the existing fields.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver uses a pointer to get from the private
bcm2835_host structure to the generic mmc_host structure. However the
latter is always immediately preceding the former in memory, so compute
its address with a subtraction (which is cheaper than a dereference) and
drop the superfluous pointer.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bcm2835_add_host() invokes IS_ERR_OR_NULL() on a DMA channel pointer,
however dma_request_slave_channel() (which was used to populate the
pointer) never returns an error pointer. So a NULL pointer check is
sufficient.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy:
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
[ad inf.]
Emulator warnings appear to be valid. The TI document SPRU680 [1]
("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card
(MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253
cycles and "0xff and 0xfe cannot be used".
Fix by using 0xfd as the maximum timeout.
Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on
real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810
(OMAP2420) that MMC works as before.
[1] http://www.ti.com/lit/ug/spru680/spru680.pdf
Fixes: 730c9b7e66 ("[MMC] Add OMAP MMC host driver")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Below are the supported DMA types in Host Control1 Register
with Version 4 enable
b'00 - SDMA
b'01 - Not Used
b'10 - ADMA2
b'11 - ADMA2 or ADMA3
ADMA3 uses Command Descriptor to issue an SD command.
A multi-block data transfer is performed by using a pair of CMD
descriptor and ADMA2 descriptor.
ADMA3 performs multiple of multi-block data transfer by using
Integrated Descriptor which is more suitable for Command Queuing
to fetch both Command and Transfer descriptors.
Host Capabilities register indicates the supports of ADMA3 DMA.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for 8-bit buswidth.
Relevant SDCR value modified.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes card initialization failure in high speed mode.
If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux
DT does not enable SDR/HS200/HS400 mode, card initialization fails in
high speed mode.
It is necessary to initialize SCC registers during card initialization
phase. HW reset function is registered only for a port with either of
SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties
are not present in device tree, SCC registers will not be reset. In SoC
that support SCC registers, HW reset function should be registered
regardless of the configuration of device tree.
Reproduction procedure:
- Use U-Boot that support MMC HS200/400 mode.
- Delete HS200/HS400 properties in device tree.
(Delete mmc-hs200-1_8v and mmc-hs400-1_8v)
- MMC port works high speed mode and all commands fail.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drop the custom code to get the 'cd' and 'wp' GPIOs. The driver now
calls mmc_of_parse() which will init these from devicetree or
device properties.
Also drop the custom code to get the 'power' GPIO. The MMC core
provides us with the means to power the MMC card through an external
regulator.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
O2 SD host controller only need set the quirk2 flag
SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD when
work on force 1.8v emmc mode but not normal mode
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mmc/host/jz4740_mmc.c:745:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mmc/host/jz4740_mmc.c:779:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of error, the function devm_kzalloc() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: fadac7488064 ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warning (W=1).
In this particular case rewrote the comment to start with the string "fall
through", so as to match the regular expression expected by GCC. Truncate
the comment slightly to fit the max line length of 80 characters.
This commit remove the following warning:
drivers/mmc/core/host.c:196:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program initial drive code offsets which will be used by auto
calibration process.
Program fixed drive strengths for SDMMC pads in pad control
register when auto cal timeouts.
Fixed settings are based on Pre-SI analysis of the pad design.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, USDHC do not generate transfer complete interrupt
when send a non-data-command with R1b response. But if want
to support DCMD in CMDQ, need to change this, the DCMD IC
logic require the USDHC to enable this function, otherwise
DCMD will never get a CC(command complete) interrupt.
This patch set ESDHC_VEND_SPEC2_EN_BUSY_IRQ and add DCMD support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CMDQ support for imx8qm/imx8qxp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change to use sdhci_set_timeout() to set the maximum timeout, so that
the host can use it's own set_timeout() callback to set the maximum
timeout if the host has.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an new esdhc_soc_data for i.MX8QXP, and add HS400_ES mode
support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some eMMC, after switch to HS400ES mode, it need to config the strobe
dll target dealy even if the clock is 50MHZ or 25MHz, otherwise will meet
CMD index/crc error when send CMD13 to check the switch status.
[ 2.473915] IRQ status 0x000a8001
[ 2.473934] mmc2: mmc_select_hs400es failed, error -84
[ 2.473938] mmc2: error -84 whilst initialising MMC card
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When removing the driver make sure to undo the PM autosuspend configured
when probing the host.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdio_bus_remove the variable is unneeded,remove it now.
Signed-off-by: wangbo <wang.bo116@zte.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1. O2 Host Controller PLL lock status is not in compliance with
CLOCK_CONTROL register bit 1
2. O2 Host Controller card detect function only work when PLL is
enabled and locked
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to handle mmc_of_parse() errors during probe otherwise the
MMC driver could start without proper initialization (e.g. power sequence).
Fixes: 476bf3d62d ("mmc: sdhci-brcmstb: Add driver for Broadcom BRCMSTB SoCs")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When host set the host->tuning_delay, even the last tuning
command need a delay, otherwise the first command after the
tuning will meet issue.
Take i.MX7D as an example, there will be the following log:
mmc2: switch to high-speed from hs200 failed, err:-110
mmc2: error -110 whilst initialising MMC card
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's observed that i.MX uSDHC needed delay between tuning
cycles for HS200 successful tuning. This patch is to set 1ms
delay for that.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
i.MX6ULL has errata ERR010450, point out that due to SOC I/O
timing limitation, for eMMC HS200 and SD/SDIO 3.0 SDR104, the
clock rate can't exceed 150MHz. And for eMMC DDR52 and SD/SDIO
DDR50 mode, the clock rate can't exceed 45MHz.
This patch add this limit for imx6ull.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed comments and whitespace]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/
MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS,
we can not do tuning reset, otherwise HS400 timing is not right.
Here is the process of init HS400, first finish tuning in HS200 mode,
then switch to HS mode and 8 bit DDR mode, finally switch to HS400
mode. If we do tuning reset in HS mode, this will cause HS400 mode
lost the tuning setting, which will cause CRC error.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR50 tuning is optinally defined in sd 3.0 spec. And i.MX
uSDHC internally already uses a fixed optimized timing for
DDR50, normally does not require tuning for DDR50 mode.
This patch specify a new execute_tuning function for i.MX
uSDHC, do not impact i.MX eSDHC.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit ESDHC_STD_TUNING_EN may be configed by bootloader code if it
choose to use standard tuning method. So on linux side, if choose to
use manual tuning method, need to clear the bit ESDHC_STD_TUNING_EN,
remove the impact of bootloader code.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variant specific driver data doesn't change at run-time, so mark it as
const to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes the following sparse warning:
drivers/mmc/host/sdhci_am654.c:161:18: warning:
symbol 'sdhci_am654_ops' was not declared. Should it be static?
Fixes: aff88ff23512 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxgqNUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwsoH+OVXu0NQofwTvVru
8lgF3BSDG2mhf7mxbBBlBizGVy9jnjRNGCFMC+Jq8IwiFLwprja/G27kaDTkpuF1
PHC3yfjKvjTeUP5aNdHlmxv6j1sSJfZl0y46DQal4UeTG/Giq8TFTi+Tbz7Wb/WV
yCx4Lr8okAwTuNhnL8ojUCVIpd3c8QsyR9v6nEQ14Mj+MvEbokyTkMJV0bzOrM38
JOB+/X1XY4JPZ6o3MoXrBca3bxbAJzMneq+9CWw1U5eiIG3msg4a+Ua3++RQMDNr
8BP0yCZ6wo32S8uu0PI6HrZaBnLYi5g9Wh7Q7yc0mn1Uh1zWFykA6TtqK90agJeR
A6Ktjw==
=scY4
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
QUEUE_FLAG_NO_SG_MERGE has been killed, so kill BLK_MQ_F_SG_MERGE too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit bb36489032 ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.
Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.
Fixes: bb36489032 ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set.
This generates a rescuer thread for that queue that will trigger when
the CPU is under heavy load and collect the uncompleted work.
In the case of mmc, this creates the possibility of a deadlock when
there are multiple partitions on the device as other blk-mq work is
also run on the same queue. For example:
- worker 0 claims the mmc host to work on partition 1
- worker 1 attempts to claim the host for partition 2 but has to wait
for worker 0 to finish
- worker 0 schedules complete_work to release the host
- rescuer thread is triggered after time-out and collects the dangling
work
- rescuer thread attempts to complete the work in order starting with
claim host
- the task to release host is now blocked by a task to claim it and
will never be called
The above results in multiple hung tasks that lead to failures to
mount partitions.
Handling complete_work on a separate workqueue avoids this by keeping
the work completion tasks separate from the other blk-mq work. This
allows the host to be released without getting blocked by other tasks
attempting to claim the host.
Signed-off-by: Zachary Hays <zhays@lexmark.com>
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC device tree bindings include properties used to signal various
signalling speed modes. Until now the sunxi driver was accepting them
without any further filtering, while the sunxi device trees were not
actually using them.
Since some of the H5 boards can not run at higher speed modes stably,
we are resorting to declaring the higher speed modes per-board.
Regardless, having boards declare modes and blindly following them,
even without proper support in the driver, is generally a bad thing.
Filter out all unsupported modes from the capabilities mask after
the device tree properties have been parsed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some H5 boards seem to not have proper trace lengths for eMMC to be able
to use the default setting for the delay chains under HS-DDR mode. These
include the Bananapi M2+ H5 and NanoPi NEO Core2. However the Libre
Computer ALL-H3-CC-H5 works just fine.
For the H5 (at least for now), default to not enabling HS-DDR modes in
the driver, and expect the device tree to signal HS-DDR capability on
boards that work.
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Fixes: 07bafc1e35 ("mmc: sunxi: Use new timing mode for A64 eMMC controller")
Cc: <stable@vger.kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
to set cmd internal delay, need set PAD_TUNE register but not PAD_CMD_TUNE
register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path. The channel may
therefore be leaked, in particular if devm_clk_get() causes probe
deferral. Fix it.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.12+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SPDX license identifier and the boiler plate text are
contradicting. Only the SPDX license identifier is needed. The
other one is removed.
Fixes: 86958dcc5a ("mmc: dw_mmc-bluefield: Add driver extension")
Cc: stable@vger.kernel.org
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Get rid of some WARN_ON() from the ACPI code
- Staticize a symbol
- Fix MMC polarity detection
-----BEGIN PGP SIGNATURE-----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=kS/C
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"The patch hitting the MMC/SD subsystem is fixing up my own mess when
moving semantics from MMC/SD over to gpiolib. Ulf is on vacation but I
managed to reach him on chat and obtain his ACK.
The other two are early-rc fixes that are not super serious but pretty
annoying so I'd like to get rid of them.
Summary:
- Get rid of some WARN_ON() from the ACPI code
- Staticize a symbol
- Fix MMC polarity detection"
* tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
mmc: core: don't override the CD GPIO level when "cd-inverted" is set
gpio: pca953x: Make symbol 'pca953x_i2c_regmap' static
gpiolib-acpi: Remove unnecessary WARN_ON from acpi_gpiochip_free_interrupts
We need to handle mmc_of_parse() errors during probe.
This finally fixes the wifi regression on Raspberry Pi 3 series.
In error case the wifi chip was permanently in reset because of
the power sequence depending on the deferred probe of the GPIO expander.
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the irq was requested through device managed resources API
(devm_request_threaded_irq()) it was freed after meson_mmc_remove()
completion, thus after mmc_free_host() has reclaimed meson_host memory.
As this irq is IRQF_SHARED, while using CONFIG_DEBUG_SHIRQ, its handler
get called by free_irq(). So meson_mmc_irq() was called after the
meson_host memory reclamation and was using invalid memory.
We ended up with the following scenario:
device_release_driver()
meson_mmc_remove()
mmc_free_host() /* Freeing host memory */
...
devres_release_all()
devm_irq_release()
__free_irq()
meson_mmc_irq() /* Uses freed memory */
To avoid this, the irq is released in meson_mmc_remove() and in
mseon_mmc_probe() error path before mmc_free_host() gets called.
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 961de0a856 ("mmc: sdhci-omap: Workaround errata regarding
SDR104/HS200 tuning failures (i929)") added a select on TI_SOC_THERMAL
for the driver to get temperature for tuning.
However, this causes the following warning on keystone_defconfig because
keystone does not support TI_SOC_THERMAL:
"WARNING: unmet direct dependencies detected for TI_SOC_THERMAL"
Fix this by changing the select to imply.
Fixes: 961de0a856 ("mmc: sdhci-omap: Workaround errata regarding
SDR104/HS200 tuning failures (i929)")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After 'commit 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set")' dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly. This driver relies on IOSF_MBI and IOSF_MBI depends
on PCI. For this reason, add a direct dependency to CONFIG_PCI here.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") gpiolib-of parses the "cd-gpios" property and flips the polarity
if "cd-inverted" is also set. This results in the "cd-inverted" property
being evaluated twice, which effectively makes it a no-op:
- first in drivers/gpio/gpiolib-of.c (of_xlate_and_get_gpiod_flags) when
setting up the CD GPIO
- then again in drivers/mmc/core/slot-gpio.c (mmc_gpio_get_cd) when
reading the CD GPIO value at runtime
On boards which are using device-tree with the "cd-inverted" property
being set any inserted card are not detected anymore. This is due to the
MMC core treating the CD GPIO with the wrong polarity.
Disable "override_cd_active_level" for the card detection GPIO which is
parsed using mmc_of_parse. This fixes SD card detection on the boards
which are currently using the "cd-inverted" device-tree property (tested
on Meson8b Odroid-C1 and Meson8b EC-100).
This does not remove the CD GPIO inversion logic from the MMC core
because there's at least one driver (sdhci-pci-core for Intel BayTrail
based boards) which still passes "override_cd_active_level = true" to
mmc_gpiod_request_cd(). Due to lack of hardware for testing this is left
untouched.
In the future the GPIO inversion logic for both, card and read-only
detection can be removed once no driver is using it anymore.
Fixes: 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device tree")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Loys Ollivier <loys.ollivier@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver
-----BEGIN PGP SIGNATURE-----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=mB5P
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
We need r8a774c0 to be whitelisted for SDHI to work on the RZ/G2E,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's been ~6 years ago since we introduced the BKOPS support for eMMC
cards. The current code is a bit messy and primarily that's because it
prepares to support running BKOPS in an asynchronous mode. However, that
mode has never been fully implemented/enabled. Instead BKOPS is always
executed in synchronously, when the card has reported an urgent BKOPS
level.
For these reasons, let's make the code more readable by dropping the unused
parts. Let's also rename mmc_start_bkops() to mmc_run_bkops(), as to make
it more descriptive.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no point checking if HPI is supported in mmc_send_hpi_cmd() as
mmc_interrupt_hpi(), which is the only caller, already checks if HPI has
been enabled. Therefore, let's drop the check and the corresponding error
path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a05 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the SDMMC pads auto calibration values parsed from
devicetree are assigned incorrectly. This patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Fixes: 51b77c8ea7 ("mmc: tegra: Program pad autocal offsets from dt")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
V4_MODE is Bit-15 of SDHCI_HOST_CONTROL2 register.
Need to perform word access to this register.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: b3f80b434f ("mmc: sdhci: Add sd host v4 mode")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
References:
[1] http://www.ti.com/lit/pdf/sprz426
[2] http://www.ti.com/lit/pdf/SPRACA9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BYT-based controllers do not have a LED signal line. Nevertheless
sdhci_led_control() takes more than twice as long as sdhci_send_command(),
even though it does nothing. Use the new SDHCI_QUIRK_NO_LED quirk to
disable LED control for Intel BYT-based controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BYT-based controllers do not have a LED signal line. Nevertheless
sdhci_led_control() takes more than twice as long as sdhci_send_command(),
even though it does nothing. Use the new SDHCI_QUIRK_NO_LED quirk to
disable LED control for Intel BYT-based controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host controllers may not have a LED signal line, whereas the register
updates to control the non-existent LED can be relatively time consuming.
Add a quirk to disable LED control.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On cmd12 (STOP_TRANSMISSION), STM32 sdmmc variant needs to set
cmdstop bit in command register. The CPSM ("Command Path State Machine")
treats the command as a Stop Transmission command and signals
abort to the DPSM ("Data Path State Machine").
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With some eMMC devices, there is still issues with the new phase
settings. Enabling signal resampling seems to solve the problem
for these.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Align the default Core and Tx phase with the SoC vendor tree.
Even if the Tx phase is different from what the documentation
recommends, it seems to provide better results.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spinlock is only used within the irq handler so it does not
seem very useful.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The host controllers on TI's AM654 SOCs are not compatible with
the phy and consumer model of the sdhci-of-arasan driver. It turns out
that for optimal operation at higher speeds, a special tuning procedure
needs to be implemented which involves configuration of platform
specific phy registers.
Therefore, branch out to a new sdhci_am654 driver and add the phy
register space with all phy configurations to it. Populate AM654
specific callbacks to sdhci_ops and add SDHCI_QUIRKS wherever
applicable.
Only add support for upto High Speed for SD card and upto DDR52 speed
mode for eMMC. Higher speeds will be added in subsequent patches.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newly added sdhci_msm_restore_sdr_dll_config() function is only called
if CONFIG_PM is enabled:
drivers/mmc/host/sdhci-msm.c:1050:12: error:
'sdhci_msm_restore_sdr_dll_config' defined but not used
[-Werror=unused-function]
Better remove the incorrect #ifdef altogether and just use __maybe_unused,
which is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Always check the wait condition before returning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mmc/host/alcor.c: In function 'alcor_data_set_dma':
drivers/mmc/host/alcor.c:124:12: warning:
variable 'len' set but not used [-Wunused-but-set-variable]
drivers/mmc/host/alcor.c:648:15: warning:
variable 'clock_out' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a spelling mistake in a pr_warn message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The rtsx USB parent device, has logic to detect when a card is inserted
into the card slot. Although, the logic can't detect when a card is
removed. This makes things a bit tricky, which is why the current method is
simply to turn on MMC_CAP_NEEDS_POLL during probe.
Using MMC_CAP_NEEDS_POLL means lots of energy being wasted, as the mmc host
becomes runtime resumed frequently by the mmc core, while it polls for new
cards being inserted.
To address this problem, let's start relying on that the rtsx USB driver
runtime resumes its child device, which is the rtsx_usb_sdmmc device, when
it detects that a new card being inserted.
This means dropping MMC_CAP_NEEDS_POLL from being set during probe. Instead
let's implement a ->runtime_resume() callback to schedule a detect work and
to set MMC_CAP_NEEDS_POLL. In this way, polling is enabled as long as there
is card inserted, thus we can rely on the mmc core to detect also when the
card becomes removed.
Furthermore, to avoid polling forever after a card has been removed, let's
implement a ->runtime_suspend() callback and make it clear
MMC_CAP_NEEDS_POLL.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
The current implementation uses the runtime PM autosuspend feature with a
default timeout set to 50ms. This really doesn't makes sense, as it's a USB
driven host device, which needs it rtsx USB device (parent device) to be
runtime resumed to provide power to the card.
In practise, using the autosuspend or any async runtime PM suspend method,
means unnecessary delaying the host device and thus the parent, to be
runtime suspended when a card is removed/powered off. For this reasons,
let's simply drop the support for runtime PM autosuspend and tell the mmc
core to use synced runtime PM suspend methods, via setting
MMC_CAP_SYNC_RUNTIME_PM during probe.
Moreover, as the mmc core nowadays deploys runtime PM reference counting of
the mmc host device, convert ->set_ios() to use the more lightweight
pm_runtime_get_noresume() and pm_runtime_put_noidle() APIs.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
In case the card has been powered off, it seems silly to continue to allow
the led to be updated. Instead let's forbid that, as it enables us to
prevent runtime resuming the device and thus avoids wasting energy.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
To allow mmc host drivers to inform the mmc core about rather using
pm_runtime_put_sync_suspend() instead of pm_runtime_put_autosuspend(),
let's introduce MMC_CAP_SYNC_RUNTIME_PM.
This is especially useful for those mmc host drivers that don't benefit
from using the runtime PM autosuspend feature. Typically this is those that
relies on parent devices to power the card via runtime PM, like some USB
host drivers for example.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
The Clock Data Recovery (CDR) circuit allows to automatically adjust
the RX sampling-point/phase for high frequency cards (SDR104, HS200...).
CDR is automatically enabled during DLL configuration.
However, according to the APQ8016 reference manual, this function
must be disabled during TX and tuning phase in order to prevent any
interferences during tuning challenges and unexpected phase alteration
during TX transfers.
This patch enables/disables CDR according to the current transfer mode.
This fixes sporadic write transfer issues observed with some SDR104 and
HS200 cards.
Inspired by sdhci-msm downstream patch:
https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/
Reported-by: Leonid Segal <leonid.s@variscite.com>
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver provides support for Alcor Micro AU6601 and AU6621
SD/MMC controller.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the mmc max-frequency device property for Intel BYT-based
host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All host drivers are converted to look up GPIO descriptors
from device tree, ACPI or machine descriptor tables, so now
we can delete the legacy GPIO handling using hardcoded GPIO
numbers from the kernel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After converting the PXA driver to use GPIO descriptors for
card detect and write protect it is relatively simple to
convert it to also use a descriptor for getting the optional
power control GPIO.
The polarity inversion flag can also go away from the platform
data since this is indicated in the GPIO machine descriptor
table.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This deletes the code dealing with handling card detect
and write protect passed in as platform data and makes
the host rely on just GPIO descriptors.
The card read only inversion flag has to be kept around
for now, as the core cannot handle the inversion flags
on the descriptors yet.
Since we can now rely on the descriptors to have the
right polarity, we set the "override_active_level" to
false in mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the code path for the PXAMCI hostso that
it can retrieve GPIO descriptors rather than use the
global GPIO numberspace for GPIO lines. If the GPIO
descriptor is present, it will take precedence and get
used in place of the platform data GPIO number.
We move the code around a bit so we request the card
detect first and the write protect second.
We keep the code setting the host flag for the write
protect polarity inversion semantics since the slot
GPIO core needs to be refactored to deal with this
before we can get rid of this.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify things by making the S3CMCI driver just use
slot GPIO with descriptors instead of passing around the
global GPIO numbers that we want to get rid of.
Getting the names of the GPIO chips into the machine
descriptor tables was a bit of a challenge but I think
I have them right.
The platform data supports passing in inversion flags, but
no platform is using them, and it is highly unlikely
that we will add more, so drop them. The long term plan
is to let the inversion flags on the GPIO machine
descriptor do the job.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMIO MMC driver was passing global GPIO numbers around for
card detect. It turns out only one single board in the kernel
was actually making use of this feature so it is pretty easy
to convert the driver to use only GPIO descriptors.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the SPI MMC driver to use GPIO descriptors internally
and just look those up using the standard slot GPIO
functions mmc_gpiod_request_cd() and mmc_gpiod_request_ro().
Make sure to request index 0 and 1 in accordance with the
SPI MMC DT binding, and add the same GPIOs in machine
descriptor tables on all boards that use SPI MMC in
board files.
The lines are flagged as GPIO_ACTIVE_[LOW|HIGH] as that is
what they are, and since we can now rely on the descriptors
to have the right polarity, we set the
"override_active_level" to false in mmc_gpiod_request_cd()
and mmc_gpiod_request_ro().
Cc: Hartley Sweeten <hsweeten@visionengravers.com> # Vision EP9307
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_mx_mmc_register_clks() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This was a SoC issue on LX2160A Rev1.0.
eSDHC_DLLCFG1[DLL_PD_PULSE_STRETCH_SEL] must be set to 0 to
get 4 delay cells in the pulse width detection logic for eMMC
HS400 mode. Otherwise it would cause unexpected HS400 issue.
This patch is to clear this bit always for affected SoC when
reset for all, since this bit doesn't affect other speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are timing violations in case of few division ratio options
are selected for card clock frequency. prescaler*divisor options
/3,/5,/6,/7,/9,/10,/11,/13,/14 and /15 are not available in LX2
Rev1.0. prescaler*divisor options /4,/8 and /12 only available in
LX2 Rev1.0. Applicable only for HS400 mode. so by add the erratum
A011334 support to limit the prescaler*divisor in LX2 REV1.0
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC controllers need specific settings for HS400 mode before the
speed mode can be switched to DDR mode, during the HS400 initialization
sequence. For that reason, let's introduce a new host callback,
->hs400_prepare_ddr() and invoked it just before switching to DDR mode.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_execute_tuning() function has assignment of
private pointers multiple times. Remove the redundant assignment.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TRM (SPRUIC2C - January 2017 - Revised May 2018 [1]) forbids
assertion of data reset while tuning is happening. Implement a
platform specific callback that takes care of this condition.
[1] http://www.ti.com/lit/pdf/spruic2 Section 25.5.1.2.4
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As reported by Aaro, the JZ4740 MMC driver throws a warning when the kernel
is built without preemption (CONFIG_PREEMPT_NONE=y).
[ 16.461094] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 567 host->next_data.cookie 568
[ 16.473120] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 568 host->next_data.cookie 569
[ 16.485144] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 569 host->next_data.cookie 570
[ 16.497170] jz4740-mmc 13450000.mmc: [jz4740_mmc_prepare_dma_data] invalid cookie: data->host_cookie 570 host->next_data.cookie 571
The problem seems to be related to how pre_req/post_req is implemented.
Currently, it seems the driver expects jz4740_mmc_prepare_dma_data() to be
called with monotonically increasing host_cookie values, which is wrong.
Moreover, the implementation is overly complicated, keeping track of
unneeded "next cookie" state.
So, instead of attempting to fix the current pre_req/post_req
implementation, this commit refactors the driver, dropping the state,
following other drivers such as dw_mmc and sdhci.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refer to "4.15 set block count command" of sd specification:
Host needs to issue CMD12 if any error is detected in
the CMD18 and CMD25 operations.
In sbc case, the data->stop is fill by framework.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some variants (namely Renesas SDHI) have bits in the STATS and IRQ_MASK
registers which are 'always 1' and should be written as such. Introduce
a seperate mask for this and apply it whenever such a register is
written.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Renesas BSP confirms that H3 ES1.x and M3-W ES1.[012] do not
properly support HS400. Add a quirk to indicate this and disable HS400
in the MMC capabilities if the quirk is set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was though all ES revisions of H3 and M3-W SoCs required the
TMIO_MMC_HAVE_4TAP_HS400 flag. Recent datasheet updates tells us this is
not true, only early ES revisions of the SoC do.
Since quirk matching based on ES revisions is now used to handle the
flag it's possible to align all Gen3 compatibility properties. This will
allow later ES revisions of H3 and M3-W to use the correct 8-tap HS400
mode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Latest datasheet makes it clear that not all ES revisions of the H3 and
M3-W have the 4-tap HS400 mode quirk, currently the quirk is set
unconditionally for these two SoCs. Prepare to handle the quirk based on
SoC revision instead of compatibility value by using soc_device_match()
and set the TMIO_MMC_HAVE_4TAP_HS400 flag explicitly.
The reason for adding a new quirks struct instead of just a flag is that
looking ahead it seems more quirks needs to be handled in a SoC revision
basis.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initial value of the interrupt mask register may be different from
the H/W manual at the startup of the kernel by setting from the
bootloader. Since the error interrupts may be unmasked, the driver sets
initial value.
The initial value is only known for R-Car Gen2 and Gen3 platforms so
limit the initialization to those platforms.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD / MMC did not operate properly when suspend transition failed.
Because the SCC was not reset at resume, issue of the command failed.
Call the host specific reset function and reset the hardware in order to
add reset of SCC. This change also fixes tuning on some stubborn cards
on Gen2.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On runtime power management resume, the host clock needs to be
enabled before calling tmio_mmc_reset. If the mmc device has a power
domain entry, the host clock is enabled via genpd_runtime_resume,
running before tmio_mmc_host_runtime_resume. If the mmc device has no
power domain entry, however, genpd_runtime_resume is not called. This
patch changes tmio_mmc_host_runtime_resume to enable the host clock
before calling tmio_mmc_reset.
Based on work from Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only user was converted to fill a sbc command which is the proper
way to do it because of AutoCMD23 feature of some hosts.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case dmaengine_prep_slave_sg fails we need to call dma_unmap_sg.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are two variables len within bcm2835_prepare_dma. So rename the
result of dma_map_sg to sg_len. While we are at this add a bail out to
simplify the following change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's better to make sure that the timeout work is really terminated
before calling mmc_request_done.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are two accesses on the data requests which are not protected by
the mutex. So fix this accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to release the slave DMA channel during driver unload.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
Link: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.
This is better than giving up and leaving the machine broken for no
obvious reason.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simplify things by making the i.MX SDHCI driver just use
slot GPIO with descriptors instead of passing around the global
GPIO numbers that we want to get rid of.
As it turns out, just one single board is using the platform
data to pass in GPIOs numbers for CD and WP, so we augment this
to use a machine descriptor table instead.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power GPIO line is passed with inversion flags and all from
the platform data. Switch to using an optional GPIO descriptor and
use this to switch the power.
Augment the only boardfile to pass in the proper "power" descriptor
in the GPIO descriptor machine table instead.
As the GPIO handling is now much simpler, we can cut down on some
overhead code.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modifty the JZ4740 driver to retrieve card detect and write
protect GPIO pins from GPIO descriptors instead of hard-coded
global numbers. Augment the only board file using this in the
process and cut down on passed in platform data.
Preserve the code setting the caps2 flags for CD and WP
as active low or high since the slot GPIO code currently
ignores the gpiolib polarity inversion semantice and uses
the raw accessors to read the GPIO lines, but set the right
polarity flags in the descriptor table for jz4740.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of string pointers in the MMC slot GPIO context is
pretty dubious, allocating some 2*len extra bytes for each
label of the ro and wp pins.
Tidy this up using kasprintf() with dynamic allocation of
labels for these strings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On few SDHCI-MSM controllers, the host controller's clock tuning
circuit may go out of sync if controller clocks are gated which
eventually will result in data CRC, command CRC/timeout errors.
To overcome this h/w limitation, the DLL needs to be re-initialized
and restored with its old settings once clocks are ungated.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Existing data command CRC error handling is non-standard and does not work
with some Intel host controllers. Specifically, the assumption that the host
controller will continue operating normally after the error interrupt,
is not valid. Change the driver to handle the error in the same manner
as a data CRC error, taking care to ensure that the data line reset is
done for single or multi-block transfers, and it is done before
unmapping DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Whitelist R8A77990 E3 SoC in the SDHI driver. The SDHI core
present in the SoC is an 8tap variant of the Gen3 SDHI core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The manual does not contain information that a wait is needed in the
tuning process, this might be a leftover from early development.
Removing the wait don't have any effect on operation so delete the wait
to shorten the initialization time.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[Niklas: fixup commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver sets an incorrect clock and depends on the clock driver
knowledge of this incorrect setting to still set a 200Mhz SDn clock.
Instead of spreading the workaround between the two drivers the clock
driver should be made aware of the ES versions where the special clock
handling is needed no need to keep this workaround in the SDHI driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK() macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function sdhci_allocate_bounce_buffer() always return zero at
present, so there's no need to have a return value, that will also make
error path easier.
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHI/MMC controller in the RZ/A2 is almost the same as R-Car gen3, but
with some minor differences.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On our AT91SAM9260 board we use the same sdio bus for wifi and for the
sd card slot. This caused the atmel-mci to give the following splat on
the serial console:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44
Modules linked in:
CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14
Hardware name: Atmel AT91SAM9
[<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14)
[<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4)
[<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24)
[<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44)
[<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc)
[<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164)
[<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0)
[<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330)
[<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310)
[<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac)
[<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118)
[<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118)
[<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34)
---[ end trace 594371ddfa284bd6 ]---
This is:
WARN_ON(host->cmd);
This was fixed on our board by letting atmci_request_end determine what
state we are in. Instead of unconditionally setting it to STATE_IDLE on
STATE_END_REQUEST.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit removes the unnecessary of-node check since the
dw_mci_bluefield_match[] structure has only one entry.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We observed some premature timeouts on a virtualization platform, the log
is like this:
case 1:
[159525.255629] mmc1: Internal clock never stabilised.
[159525.255818] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[159525.256049] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001002
...
[159525.257205] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
From the clock control register dump, we are pretty sure the clock was
stablized.
case 2:
[ 914.550127] mmc1: Reset 0x2 never completed.
[ 914.550321] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 914.550608] mmc1: sdhci: Sys addr: 0x00000010 | Version: 0x00001002
After checking the sdhci code, we found the timeout check actually has a
little window that the CPU can be scheduled out and when it comes back,
the original time set or check is not valid.
Fixes: 5a436cc0af ("mmc: sdhci: Optimize delay loops")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwEZdIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAlQH/19oax2Za3IPqF4X
DM3lal5M6zlUVkoYstqzpbR3MqUwgEnMfvoeMDC6mI9N4/+r2LkV7cRR8HzqQCCS
jDfD69IzRGb52VSeJmbOrkxBWsR1Nn0t4Z3rEeLPxwaOoNpRc8H973MbAQ2FKMpY
S4Y3jIK1dNiRRxdh52NupVkQF+djAUwkBuVk/rrvRJmTDij4la03cuCDAO+Di9lt
GHlVvygKw2SJhDR+z3ArwZNmE0ceCcE6+W7zPHzj2KeWuKrZg22kfUD454f2YEIw
FG0hu9qecgtpYCkLSm2vr4jQzmpsDoyq3ZfwhjGrP4qtvPC3Db3vL3dbQnkzUcJu
JtwhVCE=
=O1q1
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rc5' into for-4.21/block
Pull in v4.20-rc5, solving a conflict we'll otherwise get in aio.c and
also getting the merge fix that went into mainline that users are
hitting testing for-4.21/block and/or for-next.
* tag 'v4.20-rc5': (664 commits)
Linux 4.20-rc5
PCI: Fix incorrect value returned from pcie_get_speed_cap()
MAINTAINERS: Update linux-mips mailing list address
ocfs2: fix potential use after free
mm/khugepaged: fix the xas_create_range() error path
mm/khugepaged: collapse_shmem() do not crash on Compound
mm/khugepaged: collapse_shmem() without freezing new_page
mm/khugepaged: minor reorderings in collapse_shmem()
mm/khugepaged: collapse_shmem() remember to clear holes
mm/khugepaged: fix crashes due to misaccounted holes
mm/khugepaged: collapse_shmem() stop if punched or truncated
mm/huge_memory: fix lockdep complaint on 32-bit i_size_read()
mm/huge_memory: splitting set mapping+index before unfreeze
mm/huge_memory: rename freeze_page() to unmap_page()
initramfs: clean old path before creating a hardlink
kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace
psi: make disabling/enabling easier for vendor kernels
proc: fixup map_files test on arm
debugobjects: avoid recursive calls with kmemleak
userfaultfd: shmem: UFFDIO_COPY: set the page dirty if VM_WRITE is not set
...
Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3f ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3f ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Andrzej Zaborowski <balrogg@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When sending out CMD23 in the blk preparation, the comment there
rightfully says:
* However, it is not sufficient to just send CMD23,
* and avoid the final CMD12, as on an error condition
* CMD12 (stop) needs to be sent anyway. This, coupled
* with Auto-CMD23 enhancements provided by some
* hosts, means that the complexity of dealing
* with this is best left to the host. If CMD23 is
* supported by card and host, we'll fill sbc in and let
* the host deal with handling it correctly.
Let's do this behaviour for RPMB as well, and not send CMD23
independently. Otherwise IP cores (like Renesas SDHI) may timeout
because of automatic CMD23/CMD12 handling.
Reported-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GLK firmware can indicate that the tuning value will be restored after
runtime suspend, but not actually do that. Add a workaround that detects
such cases, and lets the driver do re-tuning instead.
Reported-by: Anisse Astier <anisse@astier.eu>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Problem:
The card detect IRQ does not work with modern BIOS (that want
to use _DSD to provide the card detect GPIO to the driver).
Details:
The mmc core provides the mmc_gpiod_request_cd() API to let host drivers
request the gpio descriptor for the "card detect" pin.
This pin is specified in the ACPI for the SDHC device:
* Either as a resource using _CRS. This is a method used by legacy BIOS.
(The driver needs to tell which resource index).
* Or as a named property ("cd-gpios"/"cd-gpio") in _DSD (which internally
points to an entry in _CRS). This way, the driver can lookup using a
string. This is what modern BIOS prefer to use.
This API finally results in a call to the following code:
struct gpio_desc *acpi_find_gpio(..., const char *con_id,...)
{
...
/* Lookup gpio (using "<con_id>-gpio") in the _DSD */
...
if (!acpi_can_fallback_to_crs(adev, con_id))
return ERR_PTR(-ENOENT);
...
/* Falling back to _CRS is allowed, Lookup gpio in the _CRS */
...
}
Note that this means that if the ACPI has _DSD properties, the kernel
will never use _CRS for the lookup (Because acpi_can_fallback_to_crs()
will always be false for any device hat has _DSD entries).
The SDHCI driver is thus currently broken on a modern BIOS, even if
BIOS provides both _CRS (for index based lookup) and _DSD entries (for
string based lookup). Ironically, none of these will be used for the
lookup currently because:
* Since the con_id is NULL, acpi_find_gpio() does not find a matching
entry in DSDT. (The _DSDT entry has the property name = "cd-gpios")
* Because ACPI contains DSDT entries, thus acpi_can_fallback_to_crs()
returns false (because device properties have been populated from
_DSD), thus the _CRS is never used for the lookup.
Fix:
Try "cd" for lookup in the _DSD before falling back to using NULL so
as to try looking up in the _CRS.
I've tested this patch successfully with both Legacy BIOS (that
provide only _CRS method) as well as modern BIOS (that provide both
_CRS and _DSD). Also the use of "cd" appears to be fairly consistent
across other users of this API (other MMC host controller drivers).
Link: https://lkml.org/lkml/2018/9/25/1113
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: f10e4bf663 ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the lock in mmc_blk_data that is only used through a pointer
in struct mmc_queue and to protect fields in that structure with
an actual lock in struct mmc_queue.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mmc uses the block layer struct request pointer to indirect their own
lock to the mmc_queue structure, given that the original lock isn't
reachable outside of block.c. Add a lock pointer to struct mmc_queue
instead and stop overriding the block layer lock which protects fields
entirely separate from the mmc use.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge three functions initializing the queue into a single one, and drop
an unused argument for it.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors
-----BEGIN PGP SIGNATURE-----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=/4yi
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce a host helper function to share re-tuning progress
MMC host:
- sdhci: Add support for v4 host mode
- sdhci-of-arasan: Add Support for AM654 MMC and PHY
- sdhci-sprd: Add support for Spreadtrum's host controller
- sdhci-tegra: Add support for HS400 enhanced strobe
- sdhci-tegra: Enable UHS/HS200 modes for Tegra186/210
- sdhci-tegra: Add support for HS400 delay line calibration
- sdhci-tegra: Add support for pad calibration
- sdhci-of-dwcmshc: Address 128MB DMA boundary limitation
- sdhci-of-esdhc: Add support for tuning erratum A008171
- sdhci-iproc: Add ACPI support
- mediatek: Add support for MT8183
- mediatek: Improve the support for tuning
- mediatek: Add bus clock control for MT2712
- jz4740: Add support for the JZ4725B
- mmci: Add support for the stm32 sdmmc variant
- mmci: Add support for an optional reset control
- mmci: Add some new variant specific properties/callbacks
- mmci: Re-structure DMA code to prepare for new variants
- renesas_sdhi: Add support for r8a77470, r8a7744 and r8a774a1
- renesas_sdhi_internal_dmac: Whitelist r8a77970 and r8a774a1
- tmio/uniphier-sd: Add new UniPhier SD/eMMC controller driver
- tmio/renesas_sdhi: Deal properly with SCC detection during re-tune
- tmio/renesas_sdhi: Refactor/consolidate clock management
- omap_hsmmc: Drop cover detection and some unused platform data
- dw_mmc-exynos: Enable tuning for more speed modes
- sunxi: Clarify the new timing mode and enable it for the A64 controller
- various: Convert to slot GPIO descriptors"
* tag 'mmc-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (129 commits)
mmc: mediatek: drop too much code of tuning method
mmc: mediatek: add MT8183 MMC driver support
mmc: mediatek: tune CMD/DATA together
mmc: mediatek: fix cannot receive new request when msdc_cmd_is_ready fail
mmc: mediatek: fill the actual clock for mmc debugfs
mmc: dt-bindings: add support for MT8183 SoC
mmc: uniphier-sd: avoid using broken DMA RX channel
mmc: uniphier-sd: fix DMA disabling
mmc: tmio: simplify the DMA mode test
mmc: tmio: remove TMIO_MMC_HAVE_HIGH_REG flag
mmc: tmio: move MFD variant reset to a platform hook
mmc: renesas_sdhi: Add r8a77470 SDHI1 support
dt-bindings: mmc: renesas_sdhi: Add r8a77470 support
mmc: mmci: add stm32 sdmmc variant
dt-bindings: mmci: add stm32 sdmmc variant
mmc: mmci: add stm32 sdmmc registers
mmc: mmci: add clock divider for stm32 sdmmc
mmc: mmci: add optional reset property
dt-bindings: mmci: add optional reset property
mmc: mmci: add variant property to not read datacnt
...
-----BEGIN PGP SIGNATURE-----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=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
Commit b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to
get/set array") changed the way GPIO values are passed to
gpiod_get/set_array_value() and friends. The new code introduced into
mmc_pwrseq_simple_set_gpios_value() incorrectly interpretes the 'value'
argument as a bitmap of GPIO values and assigns it directly to the
'values' bitmap variable passed to gpiod_set_array_value_cansleep()
instead of filling that bitmap with bits equal to the 'value' argument.
As a result, only member 0 of the array is handled correctly.
Moreover, wrong assumption is taken about the 'values' bitmap size not
exceding the number of bits of the 'value' argument type.
Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the tuning code is becoming more and more bloated, let's make the
set cmd/data delay to inline function to avoid too much redundant code.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8183 puts the tune register at top layer, so need add new code
to support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for MSDC IP which supports both data tune and async fifo, it can
tune cmd/data together. which can save the time and make the tune
result of CMD more stable as data line are 4bit or 8bit.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().
so need call mod_delayed_work() before msdc_cmd_is_ready()
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
as the mmc core layer has the mmc->actual_clock, so fill it
and drop msdc_host->sclk.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->chan_rx is NULL when UNIPHIER_SD_CAP_BROKEN_DMA_RX quirk flag
is set. In this case, it should not set up DMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Once DMA is enabled, it is not possible to disable it because
uniphier_sd_dma_endisable() always sets the DMA_ENABLE_DMASDRW bit
regardless of the argument 'enable'. It should disable DMA when
'enable' is false.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->chan_{rx,tx} represents the DMA capability of the platform.
Even if DMA is supported, there are cases where we want to use PIO,
for example, data length is short enough as commit 5f52c35529
("mmc: tmio: use PIO for short transfers") mentioned.
Regarding the hardware control flow, we are interested in whether DMA
is currently enabled or not, instead of whether the platform has the
DMA capability.
Hence, the several conditionals in tmio_mmc_core.c end up with
checking host->chan_{rx,tx} and !host->force_pio. This is not nice.
Let's flip the flag host->force_pio into host->dma_on.
host->dma_on represents whether the DMA is currently enabled or not.
This flag is set false in the beginning of each command, then should
be set true by tmio_mmc_start_dma() when the DMA is turned on.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO_MMC_HAVE_HIGH_REG is confusing due to its counter-intuitive name.
All the TMIO MMC variants (TMIO MMC, Renesas SDHI, UniPhier SD) actually
have high registers. It is just that each of them implements its own
registers there. The original IP from Panasonic only defines registers
0x00-0xff in the bus_shift=1 review. The register area above them is
platform-dependent.
In fact, TMIO_MMC_HAVE_HIGH_REG is set only by tmio-mmc.c and used to
test the accessibility of CTL_SDIO_REGS. Because it is specific to
the TMIO MFD variant, the right thing to do is to move such registers
to tmio_mmc.c and delete the TMIO_MMC_HAVE_HIGH_REG flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CTL_RESET_SDIO register is specific to the TMIO MFD (tmio_mmc.c).
Add a new hook host->reset() for performing a platform-specific
reset sequence, and move CTL_RESET_SDIO over there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RZ/G1C (a.k.a. R8A77470) comes with three SDHI interfaces,
SDHI0 and SDHI2 are compatible with the R-Car Gen2 SDHIs, SDHI1
is compatible with R-Car Gen3 SDHIs and it can be used as
eMMC as well. This patch adds driver compatibility, and makes
sure both drivers get compiled for the R8A77470.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STM32 sdmmc variant has a different clock divider.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_finalize callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_start callback to mmci_host_ops.
Create a generic mmci_dma_start function which regroup
common action between variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch merges the prepare data functions.
This allows to define a single access to prepare data service.
This prepares integration for mmci host ops.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-Introduces dma_priv pointer to define specific
needs for each dma engine. This patch is needed to prepare
sdmmc variant with internal dma which not use dmaengine API.
-Moves next cookie to mmci host structure to share same cookie
management between all variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch creates a common mmci_dma_setup/release which calls
dma_setup/release callbacks of mmci_host_ops and manages
common features like use_dma... If there is a fallbacks to
pio mode, dma functions must check use_dma.
error management:
-mmci_dmae_setup fail if Tx and Rx dma channels are not defined
-qcom_dma_setup fail if one of both dma channels is not defined,
Qcom has no specific resource to release, just mmci dmae resource.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current arasan sdhci PHY configuration isn't compatible
with the PHY on TI's AM654 devices.
Therefore, add a new compatible, AM654 specific quirks
and a new AM654 specific set_clock function which
configures the PHY in a sane way.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the driver passes platform data as a global structure
and uses the .data of of_device_id to pass the soc_ctl_map. To
make the implementation more flexible add a single data structure
that incorporates both of the above and pass it in the .data of
of_device_id.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when gate MSDC0_HCLK, access register will hang, even the MSDC driver
will never accessing register after HCLK was gated, but for safety, need
gate the bus_clk(which used to access register) too.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "fall-through:"
comment with a proper "fall through", which is what GCC is
expecting to find.
Addresses-Coverity-ID: 1373880 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the
"deliberate fall-through" comment with a proper "fall through"
at the bottom of the case, which is what GCC is expecting to find.
Addresses-Coverity-ID: 1373887 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384
fix checkpatch --strict issues:
-CHECK: Avoid using bool structure members because of possible alignment
issues - see: https://lkml.org/lkml/2017/11/21/384
-WARNING: Avoid using bool as bitfield. Prefer bool bitfields as
unsigned int or u<8|16|32>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the dma_inprogress into mmci dma interfaces.
This allows to simplify and prepare the next dma callbacks
for mmci host ops. dma_inprogress is called in mmci_dma_data_error
and mmci_dma_finalize.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the management of dma map/unmap into
mmci dma interfaces. This allows to simplify and prepare the next dma
callbacks for mmci host ops.
mmci_dma_unmap was called in mmci_data_irq & mmci_cmd_irq functions
and can be integrated in mmci_dma_data_error.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The OMAP HSMMC driver has some elaborate and hairy handling for
passing GPIO card detect and write protect lines from a boardfile
into the driver: the machine defines a struct omap2_hsmmc_info
that is copied into struct omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() in arch/arm/mach-omap2/hsmmc.c.
However the .gpio_cd and .gpio_wp fields are not copied from
omap2_hsmmc_info to omap_hsmmc_platform_data by
omap_hsmmc_pdata_init() so they remain unused. The only platform
defining omap2_hsmmc_info also define both to -1, unused.
It turn out there are no boardfiles passing any valid GPIO
lines into the OMAP HSMMC driver at all. And since we are not
going to add any more OMAP2 boardfiles, we can delete this
card detect and write protect handling altogether.
This seems to also fix a bug: the card detect callback
mmc_gpio_get_cd() in the slot GPIO core needs to be called
by drivers utilizing slot GPIO. It appears the the boardfile
quirks were not doing this right, so this would only get
called for boardfiles, i.e. since no boardfile was using it,
never.
Just assign mmc_gpio_get_cd() unconditionally to omap_hsmmc_ops
.get_cd() so card detects from the device tree works.
AFAICT card detect with GPIO lines assigned from
mmc_of_parse() are not working at the moment, but that is
no regression since it probably never worked.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cover detection appears to be a feature protecting the SD
card on mobile phones with a slide-cover, such as some Nokia
phones. The idea seems to be to not allow access to the
SD card when the cover is open.
It is only usable with platform data from board files, but
no board file in the kernel is using it, yet it takes up
a sizeable chunk of code in the OMAP HSMMC driver.
Since we do not add new board files for the OMAPs any target
that need this should anyway reimplement it properly using
the device tree, so delete this legacy code.
The driver is marked as orphan in MAINTAINERS by the way.
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sd8686 "libertas" SDIO adapter's power is controlled with WLAN_RST
and WLAN_PD pins -- pretty much the same way as sd8787. Allow building
the power sequencing driver along with the libertas Wi-Fi driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
If the retrieveal is successful, we also request the IRQ.
As a result the private subdriver data can be removed
entirely.
Cc: Weijun Yang <york.yang@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform data for the PXAv3 driver allows passing a card
detect GPIO, but this code is not used in the kernel.
In order to not encourage the use of the old global GPIO
numberspace we need to remove this.
Card detect (and write protect) GPIO can easily be added into
the driver using machine descriptor tables instead, and the
descriptor-based (gpiod) variants of the slot GPIO APIs.
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is complicating things for no reason: the "cd"
GPIO can easily be retrieved from the device tree if present
using just mmc_gpiod_request_cd(), which will fetch the
descriptor from the device tree using the standard binding
just fine.
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the machines using the MMCI are passing GPIOs for the
card detect and write protect using the device tree or
descriptor table (one single case, Integrator/AP IM-PD1).
Drop support for passing global GPIO numbers through
platform data, noone is using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If hosts provides ops->adma_write_desc, we should not fall back to the
general sdhci_adma_write_desc().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As you are already in ISR, it is unnecessary to call spin_lock_irqsave.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.
renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
longer than device claims to support [len=126976] [max=65536]
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
and added comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eMMC controller is also a new timing mode controller, but it doesn't
have the timing mode switch. It does however have signal delay and
calibration controls, typical of Allwinner MMC controllers that support
the new timing mode.
Enable the new timing mode setting for the A64 eMMC controller. This
also enables MMC HS-DDR modes, which gives higher throughput for eMMC
chips that support it, and can deliver such throughput.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer sunxi mmc controller variants support what they call the "new
timing mode". Support for this was implemented in two ways, according
to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc
controllers had switches to select which mode was used. Both switches
had to be set to the same setting. This variant was denoted with the
.has_timings_switch field in the sunxi_mmc_cfg structure. This hardware
is only seen on the A83T.
The second type did away with the old timing mode. The clock controller
no longer had the mode selection or clock delay setting bits. In some
cases the mmc controller retained its mode selection bit, but this
always needed to be set to the new mode, or instabilities would occur.
In a few cases, such as the A64 and H6 eMMC controller, the mode
selection bit is gone, but the controller still behaves like the new
timing mode, requiring the module clock to be double the card clock
in DDR transfer modes. This variant is denoted with the
.needs_new_timings field.
This patch adds more comments explaining the two fields, as well as
the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify
its meaning.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the initial support of Secure Digital Host Controller
Interface compliant controller found in some latest Spreadtrum chipsets.
This patch has been tested on the version of SPRD-R11 controller.
R11 is a variant based on SD v4.0 specification.
With this driver, R11 mmc can be initialized, can be mounted, read and
written.
Original-by: Billows Wu <billows.wu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When Host Version 4 Enable is set to 1, SDMA uses ADMA System Address
register (05Fh-058h) instead of using register (000h-004h) to indicate
its system address of data location. The register (000h-004h) is
re-assigned to 32-bit Block Count and Auto CMD23 argument, so then SDMA
may use Auto CMD23.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.
This patch add this new mode support.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.
Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.
For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the SD host controller specification version 4.10, when
Host Version 4 is enabled, SDMA uses ADMA System Address register
(05Fh-058h) instead of using SDMA System Address register to
support both 32-bit and 64-bit addressing.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode. This patch introduced an interface to enable
v4 mode.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix inconsistent IS_ERR and PTR_ERR in tegra_sdhci_init_pinctrl_info,
the proper pointer to be passed as argument is 'pinctrl_state_1v8'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rerun the pad calibration procedure before sdhci_request() if
the 100 ms recalibration interval has been exceeded.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement HS400 specific delay line calibration procedure. This is a
Tegra specific procedure and has to be performed regardless whether
enhanced strobe or HS400 tuning is used.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse and program the HS400 DQS trim value from DT. Program a fallback
value in case the property is missing.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement tegra210_sdhci_writew() to disable card clock and issue a
reset when the tuning command is sent. This is done to prevent an
intermittent hang with around 10 % failure rate during tuning.
Add tegra186_sdhci_ops because this workaround is specific to Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tegra_sdhci_writew() defers the write to SDHCI_TRANSFER_MODE until
SDHCI_COMMAND is written. This is not necessary on Tegra210 and Tegra186
and it breaks read-modify-write operations on SDHCI_TRANSFER_MODE
because writes to SDHCI_TRANSFER_MODE aren't visible until SDHCI_COMMAND
has been written to. This results in tuning failures on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new sdhci_ops struct for Tegra210 and Tegra186 which doesn't
set the custom tuning callback used on previous SoC generations.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program the outbound sampling trim value in tegra_sdhci_reset(). Unlike
the outbound tap value this does not depend on the signaling mode and
needs to be only programmed once.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the default inbound timing adjustment tap value on reset and on
non-tunable modes.
The default tap value is not programmed on tunable modes because the
tuning sequence is used instead to determine the tap value.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable the card clock during configuration of the tap
value in tegra_sdhci_set_tap() and issue sdhci_reset() after value
change. This is a workaround to avoid propagation of a potential
glitch caused by setting the tap value.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set NVQUIRK_HAS_PADCALIB on Tegra210 and Tegra186 to enable automatic
pad drive strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Run the automatic pad calibration after voltage switching if
tegra_host->pad_calib_required is set.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the pad drive strength calibration offsets from the device tree.
Program the calibration offsets in accordance with the current signaling
mode.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disable the card clock during automatic pad drive strength calibration
and re-enable it afterwards.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Automatic pad drive strength calibration is performed on a separate pad
identical to the ones used for driving the actual bus. Power on the
calibration pad during the calibration procedure and power it off
afterwards to save power.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Configure the voltage reference used by the automatic pad drive strength
calibration procedure. The value is a magic number from the TRM.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the pinctrl state and nvidia,only-1-8-v properties from the device
tree. Validate the pinctrl and regulator configuration before unmasking
UHS modes. Implement pad voltage state reconfiguration in the mmc
start_signal_voltage_switch() callback. Add NVQUIRK_NEEDS_PAD_CONTROL
and add set it for Tegra210 and Tegra186.
The pad configuration is done in the mmc callback because the order of
pad reconfiguration and sdhci voltage switch depend on the voltage to
which the transition occurs.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This variable is unused now after some refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDR104, HS200 and HS400 need to check for SCC error. If SCC error is
detected, retuning is necessary.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for (clk = 0x80000080; new_clock >= (clock << 1); clk >>= 1)
clock <<= 1;
... is too tricky, hence I replaced with
roundup_pow_of_two(divisor) >> 2
'(clk >> 22) & 0x1' is the bit test for the 1/1 divisor, but
it is not clear. 'divisor <= 1' is easier to understand.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
renesas_sdhi_clk_start() and renesas_sdhi_clk_stop() are now only
called from renesas_sdhi_set_clock(). Merge them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using DMA, if the DMA addr spans 128MB boundary, we have to split
the DMA transfer into two so that each one doesn't exceed the boundary.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds adma_table_cnt member to struct sdhci_host to give more
flexibility to drivers to control the ADMA table count.
Default value of adma_table_cnt is set to (SDHCI_MAX_SEGS * 2 + 1).
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow SDHCI drivers to hook code before and after sdhci_request() by
making it externally visible.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After host requests RESET_FOR_ALL action, the hardware output an
interrupt for OS and waiting for the OS to approve.
Before writing this fix, ACPI GED has handled the interrupt. But
the ACPI GED belongs to a slow process, and sometimes the handling
process time is more than 100ms(Mutex wait more than 100ms). So
drop the GED solution and add this quirk fix.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In tuning mode of operation, when TBCTL[TB_EN] is set, eSDHC may report
one of the following errors :
1)Tuning error while running tuning operation where SYSCTL2[SAMPCLKSEL]
will not get set even when SYSCTL2[EXTN] is reset. OR
2)Data transaction error (e.g. IRQSTAT[DCE], IRQSTAT[DEBE]) during data
transaction errors.
This issue occurs when the data window sampled within eSDHC is in full
cycle. So, in that case, eSDHC is not able to find out the start and
end points of the data window and sets the sampling pointer at default
location (which is middle of the internal SD clock). If this sampling
point coincides with the data eye boundary, then it can result in the
above mentioned errors. Impact: Tuning mode of operation for SDR50,
SDR104 or HS200 speed modes may not work properly
Workaround: In case eSDHC reports tuning error or data errors in tuning
mode of operation, by add the erratum A008171 support to fix the issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to add tuning error codes to
judge tuning state
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here is another TMIO MMC variant found in Socionext UniPhier SoCs.
As commit b6147490e6 ("mmc: tmio: split core functionality, DMA and
MFD glue") said, these MMC controllers use the IP from Panasonic.
However, the MMC controller in the TMIO (Toshiba Mobile IO) MFD chip
was the first upstreamed user of this IP. The common driver code
for this IP is now called 'tmio-mmc-core' in Linux although it is a
historical misnomer.
Anyway, this driver select's MMC_TMIO_CORE to borrow the common code
from tmio-mmc-core.c
Older UniPhier SoCs (LD4, Pro4, sLD8) support the external DMA engine
like renesas_sdhi_sys_dmac.c. The difference is UniPhier SoCs use a
single DMA channel whereas Renesas chips request separate channels for
RX and TX.
Newer UniPhier SoCs (Pro5 and later) support the internal DMA engine
like renesas_sdhi_internal_dmac.c The register map is almost the same,
so I guess Renesas and Socionext use the same internal DMA hardware.
The main difference is, the register offsets are doubled for Renesas.
Renesas Socionext
SDHI UniPhier
DM_CM_DTRAN_MODE 0x820 0x410
DM_CM_DTRAN_CTRL 0x828 0x414
DM_CM_RST 0x830 0x418
DM_CM_INFO1 0x840 0x420
DM_CM_INFO1_MASK 0x848 0x424
DM_CM_INFO2 0x850 0x428
DM_CM_INFO2_MASK 0x858 0x42c
DM_DTRAN_ADDR 0x880 0x440
DM_DTRAN_ADDREX --- 0x444
This comes from the difference of host->bus_shift; 2 for Renesas SoCs,
and 1 for UniPhier SoCs. Also, the datasheet for UniPhier SoCs defines
DM_DTRAN_ADDR and DM_DTRAN_ADDREX as two separate registers.
It could be possible to factor out the DMA common code by introducing
some hooks to cope with platform quirks, but this patch does not touch
that for now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_set_clock() is full of quirks because different SoC vendors
extended this in different ways.
The original IP defines the divisor range 1/2 ... 1/512.
bit 7 is set: 1/512
bit 6 is set: 1/256
...
bit 0 is set: 1/4
all bits clear: 1/2
It is platform-dependent how to achieve the 1/1 clock.
I guess the TMIO-MFD variant uses the clock selector outside of this IP,
as far as I see tmio_core_mmc_clk_div() in drivers/mfd/tmio_core.c
I guess bit[7:0]=0xff is Renesas-specific extension.
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
host->clk_update() is only used by the Renesas variants, whereas
host->set_clk_div() is only used by the TMIO-MFD variants.
To cope with this mess, promote tmio_mmc_set_clock() to a new
platform hook ->set_clock(), and melt the old two hooks into it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_clk_stop(host) is equivalent to tmio_mmc_set_clock(host, 0).
This replacement is needed for the next commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The JZ4725B is the first JZ SoC version that introduced a 32-bit IMASK
register, not the JZ4750.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've successfully tested eMMC on the V3H Starter Kit board and since the
R8A77970 SoC has a single SDHI core, it can't be a subject to the known RX
DMA errata.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Remove the stray underscore in the DM_CM_DTRAN_MODE.BUS_WIDTH register
field name and fix the typo in the comment of the #define
DTRAN_MODE_CH_NUM_CH1.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Depending on MACH_JZ4740 | MACH_JZ4780 prevent us from creating a generic
kernel that works on more than one MIPS board. Instead, we just depend on
MIPS being set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable access to the RPMB on the on-board eMMC of the
Poplar board.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need r8a774a1 to be whitelisted for SDHI to work on the RZ/G2M,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc-pwrseq property is passed mmc_pwrseq_alloc() can return
-EPROBE_DEFER because driver for power sequence provider is not probed
yet. Do not show error message when this situation happens.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add ACPI support to all IPROC SDHCI variants.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert DT properties to generic device properties
so that drivers can get properties from DT or ACPI.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into for-4.20/block
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value passed to mmc_gpiod_request_cd() function is in
microseconds, but msecs_to_jiffies() requires the value to be in
miliseconds to properly calculate the delay, so adjust the value stored
in cd_debounce_delay_ms context entry.
Fixes: 1d71926bbd ("mmc: core: Fix debounce time to use microseconds")
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new of_get_compatible_child() helper to lookup the slot child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix up the related slot-node reference leak.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
after unbinding mmc I get things like this:
[ 185.294067] mmc1: card 0001 removed
[ 185.305206] omap_hsmmc 480b4000.mmc: wake IRQ with no resume: -13
The wakeirq stays in /proc-interrupts
rebinding shows this:
[ 289.795959] genirq: Flags mismatch irq 112. 0000200a (480b4000.mmc:wakeup) vs. 0000200a (480b4000.mmc:wakeup)
[ 289.808959] omap_hsmmc 480b4000.mmc: Unable to request wake IRQ
[ 289.815338] omap_hsmmc 480b4000.mmc: no SDIO IRQ support, falling back to polling
That bug seems to be introduced by switching from devm_request_irq()
to generic wakeirq handling.
So let us cleanup at removal.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 5b83b2234b ("mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the SDHI DMA interrupts enabled while the Linux driver didn't use those.
Masking those interrupts in renesas_sdhi_internal_dmac_request_dma() gets
rid of both issues...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DM_CM_RST register actually has bits 0-31 defaulting to 1s and bits
32-63 defaulting to 0s -- fix off-by-one in #define RST_RESERVED_BITS.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc block driver does not support parallel dispatch of requests. In
normal circumstances, all requests are anyway funneled through a single
work item, so parallel dispatch never happens. However it can happen if
there is no elevator.
Fix that by detecting if a dispatch is in progress and returning busy
(BLK_STS_RESOURCE) in that case
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(dest, host->virt_base, data->sg->length) where
dest is the virtual address of the SG. Same for sg_copy_from_buffer
but in the opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 53d7e098ba ("mmc: android-goldfish: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The conversion to sg_copy_{from,to}_buffer has been done in the wrong
way. sg_copy_to_buffer is a copy from an SG list to a linear buffer so
it can't replace memcpy(buf + offset, &value, remaining) where buf is
the virtual address of the SG. Same for sg_copy_to_buffer but in the
opposite way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Fixes: 5b4277814e ("mmc: atmel-mci: use sg_copy_{from,to}_buffer")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_select_hs400es() calls mmc_select_bus_width() which will continue
to set 4bit transfer mode if fail to set 8bit mode. The bus width
should not be set to 4bit in HS400es.
When fail to set 8bit mode, need return error directly for HS400es.
Signed-off-by: Hongjie Fang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When tuning each tap is issued CMD19 twice and the result of both runs
recorded in host->taps. If the result is different between the two runs
the wrong sampling clock position was selected. Fix this by merging the
two runs and only keep the result for each tap if it was good in both
sets.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the return value of mmc_send_tuning() is error other than -EILSEQ,
the tuning fails and process goes out of for_loop. The correct
processing is to judge their TAP as not good (NG) and continue.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent Linux versions refuse to print actual virtual kernel addresses,
to not give a hint about the location of the kernel in a randomized virtual
address space. This affects the output of the sunxi MMC controller
driver, which now produces the rather uninformative line:
[ 1.482660] sunxi-mmc 1c0f000.mmc: base:0x(____ptrval____) irq:8
Since the virtual base address is not really interesting in the first
place, let's just drop this value. The same applies to Linux' notion of
the interrupt number, which is independent from the GIC SPI number.
We have the physical address as part of the DT node name, which is way
more useful for debugging purposes.
To keep a success message in the driver, we make this purpose explicit
with the word "initialized", plus print some information that is not too
obvious and that we learned while probing the device:
the maximum request size and whether it uses the new timing mode.
So the output turns into:
[ 1.750626] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.786699] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Allwinner boards feature an on-board eMMC with fixed 3.3V voltage
(e.g. Banana Pi M2+), and in this case both the eMMC and the SoC are
capable of doing 3.3V DDR transmission.
Add capability of 3.3V DDR when DDR is available (extra clock or new
timing).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step to improve the variant specific code for mmci, add a
->dma_setup() callback to the struct mmci_host_ops.
To show its use, let's deploy the callback for the qcom dml, which involves
also to the assign the mmci_host_ops pointer from the variant ->init()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.
Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tegra SDHCI controllers require the SDHCI clock divider to be configured
to divide the clock by two in DDR50/52 modes. Incorrectly configured
clock divider results in corrupted data.
Prevent the possibility of incorrectly calculating the divider value due
to clock rate rounding or low parent clock frequency by not assigning
host->max_clk to clk_get_rate() on tegra_sdhci_set_clock().
See the comments for further details.
Fixes: a8e326a ("mmc: tegra: implement module external clock change")
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MSI interrupt support if the SD host device can support MSI interrupt.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci tuning function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
O2 SD Host HS200 mode clock frequency current is 208MHz, should be changed
to 200MHz to meet specification.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use eMMC as boot device, the eMMC signaling voltage is tied to 1.8v
fixed output voltage, bios can set o2 sd host controller PCI configuration
register 0x308 bit4 to 1 to let driver skip 3.3v signaling voltage and
direct use 1.8v singling voltage in eMMC initialize process.
Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement and use tegra_sdhci_get_max_clock() which returns the true
maximum host clock rate. The issue with tegra_sdhci_get_max_clock() is
that it returns the current clock rate of the host instead of the
maximum one, which can lead to unnecessarily small clock rates.
This differs from the previous implementation of
tegra_sdhci_get_max_clock() in that it doesn't divide the result by two.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the uSDHC case (e.g. i.MX 6) clocks only get disabled if frequency
is set to 0. However, it could be that the stack asks for a frequency
change while clocks are on. In that case the function clears the
divider registers (by clearing ESDHC_CLOCK_MASK) while the clock is
enabled! This causes a short period of time where the clock is
undivided (on a i.MX 6DL a clock of 196MHz has been measured).
For older IP variants the driver disables clock by clearing some bits
in ESDHC_SYSTEM_CONTROL.
Make sure to disable card clock before changing frequency for uSDHC
IP variants too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems that SD3.0 advertisement needs to be set for higher eMMC
speed modes (namely DDR52) as well. The TRM states that the SD3.0
advertisement bit should be set for all controller instances, even
for those not supporting UHS-I mode...
When specifying vqmmc-supply as a fixed 1.8V regulator on a Tegra
SD/MMC instance which is connected to a eMMC device, the stack
enables SD3.0. However, enabling it has consequences: If SDHCI 3.0
support is advertised the stack enables Auto-CMD23. Unfortunately
Auto-CMD23 seems not to work well with Tegra 3 currently. It leads
to regular warnings:
mmc2: Got command interrupt 0x00010000 even though no command operation was in progress.
It is not entirely clear why those errors happens. It seems that
a Linux 3.1 based downstream kernel which has Auto-CMD23 support
does not show those warnings.
Use quirk SDHCI_QUIRK2_ACMD23_BROKEN to prevent Auto-CMD23 being
used for now. With this the eMMC works stable on high-speed mode
while still announcing SD3.0.
This allows to use mmc-ddr-1_8v to enables DDR52 mode. In DDR52
mode read speed improves from about 42MiB/s to 72MiB/s on an
Apalis T30.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make sure the clock is doubled when using eMMC DDR52 mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stack assumes that SDHC controller which support SD3.0 (SDR104) do
support HS200. This is not the case for Tegra 3, which does support SD
3.0
but only supports eMMC spec 4.41.
Use SDHCI_QUIRK2_BROKEN_HS200 to indicate that the controller does not
support HS200.
Note that commit 156e14b126 ("mmc: sdhci: fix caps2 for HS200") added
the tie between SD3.0 (SDR104) and HS200. I don't think that this is
necessarly true. It is fully legitimate to support SD3.0 and not support
HS200. The quirk naming suggests something is broken in the controller,
but this is not the case: The controller simply does not support HS200.
Fixes: 7ad2ed1dfc ("mmc: tegra: enable UHS-I modes")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys has DWC MSHC controller on HPAS-DX platform connected using PCIe
interface with SD card slot and eMMC device slots. This patch is to
enable SD cards connected on this platform. As Clock generation logic
is implemented using MMCM module of HAPS-DX platform, we have separate
functions to control the MMCM to generate required clocks with respect
to speed mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a driver for SDHCI OF Synopsys DesignWare Cores Mobile Storage
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
For eMMC devices it is valid to only support 1.8V signaling. When
vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V
initially and prints the following warning:
mmc1: Switching to 3.3V signalling voltage failed
Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is
not available. This prevents the stack from even trying to use
3.3V signaling and avoids the above warning.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.
Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A recent commit introduced a call to mmc_of_parse() and removed the
explicit assignment of GPIOs in the pdata structure. This will leave
them set to 0, which is a valid GPIO per se, so the code that looks
at these members will try to allocate them and fail.
To fix this properly, make the following changes:
a) Refrain from allocating and assiging a pdata struct from
pxamci_of_init(). It's a hack to do it this way anyway.
Instead, move the only remaining member of interest in
'struct pxamci_host' and assign the value from either
the passed in pdata pointer or with the value read from DT.
b) Let the only user of 'detect_delay_ms' look at the member of
'struct pxamci_host', not the pdata.
c) Make more code in pxamci_probe() dependent on the presence of
actual pdata.
This will also ease the removal of pdata one day.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Strip some code by letting the mmc core handle the regulators. The old
.gpio_power pdata handling is kept around for now.
This also set the voltage on the regulator and handles -EPROBE_DEFER
correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Devicetree-enabled boards should use proper regulators to control the
power of cards, not GPIOs, so let's remove this property. The regulator
properties are supported by the MMC core and are described in the
generic MMC document:
Documentation/devicetree/bindings/mmc/mmc.txt
Note that devicetree support for PXA platforms hasn't fully landed yet,
so this binding does not have any users at this point.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Call into mmc_of_parse() from pxamci_of_init(). As it needs a pointer to a
struct mmc_host, refactor the code a bit.
This allows all generic MMC properties to be set that are described in
Documentation/devicetree/bindings/mmc/mmc.txt. Reword the documentation
a bit to make that clear.
The "cd" and "wp" gpio lookups are removed as the lookup will now be
done by mmc_of_parse().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pxamci_of_init() had some weird indenting.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These gpio assignments don't make sense, as they are not used anywhere.
Remove the dead code.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These members are no longer in use, so let's remove them.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This seems to be a left-over from times before the IRQ was handled by devm
functions. Remove it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The field support_vsel is currently only used in the device tree
case. Get rid of it. No change in behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The uSDHC supports DDR modes for eMMC devices running at 3.3V. This
allows to run eMMC with 3.3V signaling voltage at DDR52 mode:
# cat /sys/kernel/debug/mmc1/ios
clock: 52000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 3 (8 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to use of_match_node method to fix up eSDHC clock for
ls1046a/ls1012a/p1010. Also add eSDHC clock fixup for ls1021a
according to its datasheet. The maxmum speed for ls1021a eSDHC
high speed mode is 46.5MHz.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers immediately report SDHCI_CLOCK_INT_STABLE after
enabling the clock even when the clock is not stable. When used in
conjunction with older/slower cards, this can result in:
mmc0: error -84 whilst initialising SD card
When the stable reporting is known to be broken, we simply wait for the
maximum stabilization period.
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to use the new compatible string "qcom,sdhci-msm-v5".
Based on the msm variant, pick the relevant variant data and
use it for register read/write to msm specific registers.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In addition to offsets of certain registers changing, the registers in
core_mem have been shifted to HC mem as well. To access these
registers, define msm version specific functions. These functions can
be loaded into the function pointers at the time of probe based on
the msm version detected.
Also defind new data structure to hold version specific Ops and
register addresses.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDCC version 5.0.0, MCI registers are removed from SDCC
interface and some registers are moved to HC.
Define a new data structure where we can statically define
the address offsets for the registers in different SDCC versions.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete
These supplement the existing HS400 operation:
* prepare_hs400_tuning
This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
This can be done in an implementation of complete_hs400_tuning
If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_exynos_resume_noirq() performs DWMMC register access without
ensuring that respective clocks are enabled. This might cause external
abort on some systems (observed on Exynos5433 based boards). Fix this
by forcing a PM runtime active state before register access. Using
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS allows also to cleanup conditional code
a bit.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.
The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc host controller enters suspend state, the clocks are
disabled, but irqs are not. For some reason the irqchip emits
false interrupts, which causes system lock loop.
Debug log is:
...
sunxi-mmc 1c11000.mmc: setting clk to 52000000, rounded 51200000
sunxi-mmc 1c11000.mmc: enabling the clock
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 6(80000146) arg 3210101 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 AGND3R 14.6 GiB
mmcblk1boot0: mmc1:0001 AGND3R partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 AGND3R partition 2 4.00 MiB
sunxi-mmc 1c11000.mmc: cmd 18(80003352) arg 0 ie 0x0000fbc2 len 409
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00004000 idi 00000002
mmcblk1: p1
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
and so on...
This issue apears on eMMC cards, routed on MMC2 slot. The patch is
tested with A20-OLinuXino-MICRO/LIME/LIME2 boards.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc95 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bfd694d5e2 ("mmc: core: Add tunable delay
before detecting card after card is inserted") adds
"u32 cd_debounce_delay_ms" to the last of mmc_gpio
struct and cause "char cd_label[0]" NOT work as string
pointer of card detect label, when "cat /proc/interrupts",
the devname for card detect gpio is incorrect as below:
144: 0 gpio-mxc 22 Edge ▒
161: 0 gpio-mxc 7 Edge ▒
Move the cd_label field down to fix this, and drop the
zero from the array size to prevent future similar bugs,
the result is correct as below:
144: 0 gpio-mxc 22 Edge 2198000.mmc cd
161: 0 gpio-mxc 7 Edge 2190000.mmc cd
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card after card is inserted")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is fixes an issue that the SDHI_INTERNAL_DMAC_RX_IN_USE
flag cannot be cleared because tmio_mmc_core sets the host->data
to NULL before the tmio_mmc_core calls tmio_mmc_abort_dma().
So, this patch clears the SDHI_INTERNAL_DMAC_RX_IN_USE in
the renesas_sdhi_internal_dmac_abort_dma() anyway. This doesn't
cause any side effects.
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes an issue that lacks the dma_unmap_sg() calling in
the error patch of renesas_sdhi_internal_dmac_start_dma().
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching
-----BEGIN PGP SIGNATURE-----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=MwCT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
This reverts commit e060d376cc ("mmc: renesas_sdhi: fix WP detection")
and adds some code to really fix the regressions.
It was missed so far that Renesas R-Car instantiations of SDHI chose to
disable internal WP and used the existence of "wp-gpios" to en/disable
WP at all.
With the first refactoring by Yamada-san with commit 2ad1db059b ("mmc:
renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of TMIO own flag"),
WP was always disabled even when GPIOs were present. With Wolfram's
first fix which gets now reverted, GPIOs were honored. But when not
available, the fallback was to internal WP and not to disabled WP. This
caused wrong WP status on uSD card slots.
Restore the old behaviour now. By default, WP is disabled. When a GPIO
is found, the GPIO re-enables WP. We will think about possible better
ways to handle this in the future.
Tested on a previously regressing Renesas Lager board (H2) and a still
working Renesas Salvator-X board (M3-W).
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
There is no obvious reasons to why mvsdio shouldn't be able to support
erase/trim/discard operations, hence let's set MMC_CAP_ERASE for it.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Instead of using a hardcoded timeout of 5 * HZ jiffies, let's respect the
command busy timeout provided by the mmc core. This make the used timeout
more reliable.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Now we have a proper implementation for the power irq handling and this
quirk is not needed anymore. In fact, it is causing card detection delays
on apq8096 platforms and the following error is displayed:
sdhci_msm 74a4900.sdhci: mmc0: pwr_irq for req: (4) timed out
The quirk is forcing the controller to retain 1.8V signalling on the slot
even when a new card is inserted, which is not correct. The proper behavior
would be to reset the controller in order to start with 3.3V signaling.
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Suggested-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
[While this keeps existing behavior it seems to mismatch the comment,
maintainers please chime in!]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The highmem conversion caused a build error in some configurations:
drivers/mmc/host/mxcmmc.c: In function 'mxcmci_transfer_data':
drivers/mmc/host/mxcmmc.c:622:10: error: implicit declaration of function 'kmap_atomic'; did you mean 'in_atomic'? [-Werror=implicit-function-declaration]
This includes the correct header file.
Fixes: b189e7589f ("mmc: mxcmmc: handle highmem pages")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newly added runtime-pm functions cause a harmless warning
when CONFIG_PM is disabled:
drivers/mmc/host/sunxi-mmc.c:1452:12: error: 'sunxi_mmc_runtime_suspend' defined but not used [-Werror=unused-function]
static int sunxi_mmc_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/sunxi-mmc.c:1435:12: error: 'sunxi_mmc_runtime_resume' defined but not used [-Werror=unused-function]
static int sunxi_mmc_runtime_resume(struct device *dev)
This marks them as __maybe_unused to shut up the warning.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This drastically reduces the rate at which the MMC_SEND_STATUS cmd polls
for completion of the MMC Erase operation. The patch does this by adding
a backoff sleep that starts by sleeping for short intervals (128-256us),
and ramps up to sleeping for 32-64ms.
Even on very quickly completing erase operations, the loop iterates a few
times, so not too much extra latency is added to these commands.
For long running discard operarations, like a full-device secure discard,
this change drops the interrupt rates on my single-core NXP I.MX6UL from
45000/s to about 20/s, and greatly improves system responsiveness.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmap_atomic to map the scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO card detect state. This allows users with GPIOs that
never sleep to avoid a warning when certain quirks are present.
The sdhci controller has an SDHCI_QUIRK_NO_CARD_NO_RESET, which
indicates that a controller will not reset properly if no card is
inserted. With this quirk enabled, mmc_get_cd_gpio is called in
several places with a spinlock held and interrupts disabled.
gpiod_get_raw_value_cansleep is not happy with this situation,
and throws out a warning.
For boards that a) use controllers that have this quirk, and b) wire
card detect up to a GPIO that doesn't sleep, this is a spurious warning.
This change silences that warning, at the cost of pushing this problem
down to users that have sleeping GPIOs and controllers with this quirk.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I noticed below error msg with sdhci-pxav3 on some berlin platforms:
[.....] sdhci-pxav3 f7ab0000.sdhci failed to add host
It is due to getting related vmmc or vqmmc regulator returns
-EPROBE_DEFER. It doesn't matter at all but it's confusing.
>From another side, if driver probing fails and the error number isn't
-EPROBE_DEFER, the core will tell us something as below:
[.....] sdhci-pxav3: probe of f7ab0000.sdhci failed with error -EXX
So it's not necessary to emit error msg if sdhci_add_host() fails. And
some other sdhci host drivers also have this issue, let's fix them
together.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the calls to ->prepare_hs400_tuning(), from mmc_retune() into
mmc_hs400_to_hs200(), as it better belongs there, rather than being generic
to all type of cards.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sg_copy_{from,to}_buffer to bounce buffer and kmap_atomic to map the
scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass the scatterlist on to the USB subsystem instead of expecting a
kernel virtual address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmap_atomic to map the scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This handles highmem pages, and also cleans up the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This handles highmem pages, and also cleans up the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's pointless to switch and trace partition type if the current
selected device partition is the same with that one. Moreover, cycled
claiming host associated with mmc_blk_part_switch() could make
mmc_blk_remove() end up waiting for grabbing the context if it's
occupied, which lead requests could still hit the low-level drivers,
if an asynchronous unbind for host drivers happened, as the card hasn't
been set removed in the remove path.
So a simple dd in background:
dd if=/dev/mmcblk0 of=/dev/null bs=512k count=100000 &
and doing unbind then:
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind
could make the console stuck for quite a while depending on the
numbers of requests.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_QUIRK2_HOST_OFF_CARD_ON is needed for the driver to
properly reset the host controller (reset all) on initialization
after exiting deep sleep.
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Fixes: c833e92bbb ("mmc: sdhci-iproc: support standard byte register accesses")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.
Fixes: b17b4ab8ce ("mmc: sdhci-iproc: define MMC caps in platform data")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 97548575be ("mmc: block: Convert RPMB to a character device") a
new function `mmc_rpmb_ioctl` was added. The final return is simply
returning a value of `0` instead of propagating the correct return code.
Discovered during a compilation with W=1, silence the following gcc warning
drivers/mmc/core/block.c:2470:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trigger the reset line of the mmc controller while probing, if available.
The reset should be optional for now, at least until all related DT nodes
have the reset property.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds extension to the dw_mmc driver for Mellanox BlueField
SoC. It updates the UHS_REG_EXT register to bring up the eMMC card on
this SoC.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.
However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.
With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Switch everyone to blk_get_request_flags, and then rename
blk_get_request_flags to blk_get_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A redundant return statement is removed from
tegra_sdhci_set_uhs_signaling(). The function returns void and the
return does not affect the control flow of the function.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using a fixed 3s timeout for commands with R1B responses,
convert to use the per request calculated busy timeout from the mmc core.
This is needed to cope with requests that requires longer timeout, for
example erase/discard commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Instead of having to return -EINVAL when requested to send SDIO specific
commands, let's set MMC_CAP2_NO_SDIO as it completely prevents them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Let's implement the ->sw_reset() bus ops to allow SDIO func drivers, in
particular, to make a SW reset without doing a full power cycle of the SDIO
card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().
Make the function internally available to the mmc core, as to allow the
following changes to make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.
However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.
To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.
The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 8d20b2eae6 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add sdhci_omap_enable_sdio_irq to set CTPL and CLKEXTFREE bits in
MMCHS_CON register required to detect asynchronous card interrupt
on DAT[1].
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the new compatible added specifically to support
k2g's MMC/SD controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.
The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out the target_timeout calculation so it can be re-used.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.
Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.
Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i843 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
PG 1.0/1.1 silicon has limitations w.r.t frequencies at which MMC1/2/3
can operate.
Use soc_device_match() to identify rev 1.0/1.1 silicon and
override mmc->f_max according to the errata workaround.
"max-frequency" dt property cannot be used since the device
tree is added for rev 2.0 silicon.
soc_device_match() is also used in order to get the IODelay values
for rev 1.0/1.1 silicon.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci can directly get ADMA capability from MMCHS_CAPA register.
Remove explicitly setting ADMA here as some instances might not have
ADMA enabled. (sdhci_read_caps() is also removed from here since
sdhci_setup_host() invokes it).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Remove the local_irq_save() invocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While performing R/W access in PIO mode, the common SDHCI driver checks
the buffer ready status once per whole block processing. That is, after
getting an appropriate interrupt, or checking an appropriate status bit,
the driver makes buffer accesses for the whole block size (e.g. 128 reads
for 512 bytes block). This is done in accordance with SD Host Controller
Specification.
At the same time, the Ultra Secured Digital Host Controller (uSDHC), used
in i.MX6 (and, probably, earlier i.MX series too), uses a separate
Watermark Levels register, controlling the amount of data or space
available when raising status bit or interrupt. For default watermark
setting of 16 words, the controller expects (and guarantees) no more
than 16 buffer accesses after raising buffer ready status bit and
generating an appropriate interrupt. If the driver tries to access the
whole block size, it will get incorrect data at the end, and a new
interrupt will appear later, when the driver already doesn't expect it.
This happens sometimes, more likely on low frequencies, e.g. when
reading EXT_CSD at MMC card initialization phase
(which makes that initialization fail).
Such behavior of i.MX uSDHC seems to be non-compliant
to SDHCI Specification, but this is the way it works now.
In order not to rewrite the SDHCI driver PIO mode access logic,
the IMX specific driver can just set the watermark level to default
block size (128 words or 512 bytes), so that the controller behavior
will be consistent to generic specification. This patch does this
for PIO mode accesses only, restoring default values for DMA accesses
to avoid any possible side effects from performance point of view.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.
SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During probe check whether the vdd-io regulator of sdhc platform device
can support 1.8V and 3V and store this information as a capability of
platform device.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've successfully tested eMMC on R8A77980/Condor. R8A77980 has a single
SDHI core anyway, so can't be a subject of the known RX DMA errata...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the code block inside the for loop will never execute more than
once, because the function returns immediately after the first iteration,
hence the execution of the code at the second iteration is structurally
dead and, code at line 281: return 0; is never reached.
Fix this by checking _ret_ before return.
Addresses-Coverity-ID: 1468009 ("Logically dead code")
Addresses-Coverity-ID: 1468002 ("Structurally dead code")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call msdc_drv_probe() is to match an entry in
msdc_of_ids[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix 3.3V voltage switch for some BYT-based Intel controllers by making use
of the ACPI DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The WARN can never trigger because we limited the max_seg number in
renesas_sdhi_of_data already. Remove it and update the comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Whitelisting every ES version does not scale. So, we whitelist whole
SoCs independent of ES version. If we need specific handling for an ES
version, we put it to the front, so it will be matched first.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometimes sg->offset is not used for buffer addresses allocated by
dma_map_sg(), so alignment checks should be done on the allocated buffer
addresses. Delete the alignment check for sg->offset that is done before
dma_map_sg(). Instead, it performs the alignment check for
sg->dma_address after dma_map_sg().
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: broke this commit in two and tidied small style issue]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of directly accessing the members of struct scatterlist use the
helpers mmc_get_dma_dir() and sg_dma_address() in
renesas_sdhi_internal_dmac_start_dma(). Based on previous work by
Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some NI 904x devices, using 3.3V signaling for extended periods of
time will physically damage the pads connected to the SDHC, eventually
causing complete failure of the controller. To work around this,
require that we avoid 3.3V signaling.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our set_ios hook is, when the card is power up or down, either doing a full
init or put our controller back into a reset mode.
Since we're also doing that in our runtime_pm hooks, and at possibly much
more often, we can drop it from the set_ios, and either rely on our
runtime_pm hooks or our probe to do it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far, even if our card was not in use, we didn't shut down our MMC
controller, which meant that it was still active and clocking the bus.
While this obviously means that we could save some power there, it also
creates issues when it comes to EMC control since we'll have a perfect peak
at the card clock rate.
Let's implement runtime_pm with autosuspend so that we will shut down the
controller when it's not been in use for quite some time.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the card setup
to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the clock setup
to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the bus width
setup to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the other functions in the driver take a struct sunxi_mmc_host pointer.
Let's make it consistent.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR52 with 8-bit mode should be handled in a different way when
requesting ciu_clk. However DDR50 is used for SDMMC/SDIO and
could never be possible with 8-bit mode. It's trival but misleading.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Explicitly update the docomentation to support the Meson-AXG platform.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Introduce the compatible data to cover the register offset & mask
change of the eMMC controller in Amlogic's Meson-AXG SoC.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace dma_request_channel() with dma_request_chan(),
which also supports probing from the devicetree.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the JZ4780 MMC controller to the jz47xx_mmc driver. There
are a few minor differences from the 4740 to the 4780 that need to be
handled, but otherwise the controllers behave the same. The IREG and IMASK
registers are expanded to 32 bits. Additionally, some error conditions are
now reported in both STATUS and IREG. Writing IREG before reading STATUS
causes the bits in STATUS to be cleared, so STATUS must be read first to
ensure we see and report error conditions correctly.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The maximum clock rate can be overridden by DT. The clock rate should
be set to the DT-specified value rather than the constant JZ_MMC_CLK_RATE
when this is done. If the maximum clock rate is not set by DT then
mmc->f_max will be set to JZ_MMC_CLK_RATE.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to probe the device via devicetree, which
will be used to support other SoCs such as the JZ4780.
Based on commits from the CI20 repo, by Paul Cercueil
and Alex Smith. Binding document based on work by
Zubair Lutfullah Kakakhel.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case a bootloader leaves the device in a bad state,
requesting the interrupt before resetting results in a bad
interrupt loop.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
[Ezequiel: cleanup commit description]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of accessing the platform data pointer directly,
use the dev_get_platdata() helper.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a minor cleanup to order the headers alphabetically.
This helps prevent merge conflicts.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, if jz4740_mmc_request_gpios() fails, the driver
tries to release DMA resources. This is wrong because DMA
is requested at a later stage.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[Ezequiel: cleanup commit message]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently driver is using a VLA declared using the number of descriptors. This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values. Memory is
free'd before return from function.
>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On SD 2.00 cards we get lots of these messages:
"mmc0: Got data interrupt 0x00000002 even though no data operation was in progress"
By applying the SDHCI_QUIRK2_STOP_WITH_TC quirk, the messages no longer happen.
A single card claiming to be SD 3.00 compliant also generates the interrupts,
but since the card's manfacturing date is 2002 mar, it's unlikely to really be
SD 3.00. This card is a 8GB SanDisk 'SU08G' 8.0 (SDHC class 4).
This has been reported on Xilinx devices that also use the Arasan IP.
See https://patchwork.kernel.org/patch/8062871/
This has been tested on the Renesas RZ/ND-DB board with the RZ/N1 SoC. The
Arasan IP in this device is version 1.39a and uses a max SD clock of 50MHz and
does not support DDR modes.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode
- renesas_sdhi_internal_dmac: Avoid data corruption by limiting DMA RX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jO/Y
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode
- renesas_sdhi_internal_dmac: Avoid data corruption by limiting
DMA RX"
* tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs
mmc: sdhci-pci: Only do AMD tuning for HS200
Early revisions of certain SoCs cannot do multiple DMA RX streams in
parallel. To avoid data corruption, only allow one DMA RX channel and
fall back to PIO, if needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit c31165d740 ("mmc: sdhci-pci: Add support for HS200 tuning mode
on AMD, eMMC-4.5.1") added a HS200 tuning method for use with AMD SDHCI
controllers. As described in the commit subject, this tuning is specific
for HS200. However, as implemented, this method is used for all host
timings, because platform_execute_tuning, if it exists, is called
unconditionally by sdhci_execute_tuning(). This breaks tuning when using
the AMD controller with, for example, a DDR50 SD card.
Instead, we can implement an amd execute_tuning wrapper callback, and
then conditionally do the HS200 specific tuning for HS200, and otherwise
call back to the standard sdhci_execute_tuning().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: c31165d740 ("mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
If an error was detected when CMD23 was issued, command sequence should
be terminated with errors and CMD23 should be issued after retuning.
Fixes: 8b22c3c18b ("mmc: tmio: add CMD23 support")
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.
Fix the bug by dropping the reference for the bus in mmc_blk_exit().
Signed-off-by: Alexander Kappner <agk@godking.net>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.
If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.
This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).
Resolve by holding the spinlock until after the IMASK register has
been updated.
Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb856 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Pd6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic"
* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
mmc: update sdio_claim_irq documentation
mmc: Export host capabilities to debugfs.
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: block: fix updating ext_csd caches on ioctl call
mmc: sunxi: Set our device drvdata earlier
mmc: sunxi: Move the reset deassertion before enabling the clocks
mmc: sunxi: Move resources management to separate functions
mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
mmc: core: Export card RCA register via sysfs
mmc: renesas_sdhi: fix WP detection
mmc: core: Use memdup_user() rather than duplicating its implementation
mmc: dw_mmc-rockchip: correct property names in debug
mmc: sd: Remove redundant err assignment from mmc_read_switch
mmc: sdio: Check the return value of sdio_enable_4bit_bus
mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
arm64: dts: hi3660: remove 'num-slots' property for dwmmc
ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
arm64: dts: stratix10: remove 'num-slots' property for dwmmc
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The blackfin architecture is getting removed, so this one
is obsolete now as well.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All our documentation says HOST_MODE, we don't really know where EXT_ACC
came from. Rename it to reduce the confusion.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice
Signed-off-by: Joel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports the host capabilities to debugfs
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Zero is a valid IRQ number and is being used on some CHT tablets. Stop
treating it as an error.
Reported-by: Luke Ross <luke@lukeross.name>
Fixes: 1b7ba57ecc ("mmc: sdhci-acpi: Handle return value of platform_get_irq")
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.
That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.
Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.
Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.
And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the pm_runtime_enable hook is called, our runtime_suspend and
runtime_resume hooks can be called as well. However, we only set the device
drvdata that we will use after we have registered into the MMC core. Move
that earlier so that we don't have a race that could lead to a crash.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As per Allwinner guidelines, the reset line should be deasserted before
turning the clocks on.
Implement it in our driver as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've had all our resources management, and especially the clocks and reset
sequence, done directly as part of the probe.
As we want to implement runtime_pm, we'll obviously want to have that
moved outside of the probe so that we can call do it in our runtime suspend
and resume hooks without too much duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hi3798CV200 SoC extends the dw-mshc controller for additional clock
and bus control. Add support for these extensions.
Signed-off-by: tianshuliang <tianshuliang@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports RCA register to sysfs which will help in reading the
disk identification information.
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling the clock, dwmmc exynos driver is trying to access the
register. Then the kernel panic can be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit "mmc: renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of
TMIO own flag" activated MMC_CAP2_NO_WRITE_PROTECT for Renesas SDHI
which incorrectly disabled WP altogether instead of only disabling the
internal mechanism. Since the whole WP handling has been reworked, we
can simply disable this capability to re-enable WP GPIOs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Following up the device tree fixed in commits e78c637127 ("ARM: dts:
rockchip: Fix DWMMC clocks") and ca9eee95a2 ("arm64: dts: rockchip:
Fix DWMMC clocks", 2018-02-15), avoid confusion by using the correct
property name in the debug output if clocks are not found.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable err would be firstly initialized by the return value of
mmc_sd_switch().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we could move card->host->caps & MMC_CAP_4_BIT_DATA
ahead of mmc_sdio_init_uhs_card, in mmc_host_uhs(). So there
we could save this bit to check that. Also, if the process of
sdio_enable_4bit_bus goes wrong, we should bails out early.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.
This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.
Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'num-slots' property had already deprecated.
Remove the 'nom-slots' property that is kept to maintain the compatibility.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'clock-freq-min-max' property had already deprecated.
Remove the 'clock-freq-min-max' property that is kept to maintain
the compatibility.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just applying the existing logic and adding its own characteristics into
the space pointed by an extra entry of struct of_device_id to have support
of MT7622 SoC.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Jumin Li <jumin.li@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However, users also want to
control it from sysfs power/wakeup attribute. That means the driver needs
to check the PM flags before enabling it in the suspend callback. Add
support for that in sdhci-pci, which is the only driver presently using the
MMC_CAP_CD_WAKE flag, and remove the enabling in mmc_gpiod_request_cd_irq()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Do not enable wakeup for SDIO card interrupt unless the SDIO function
driver has requested it which is indicated by mmc_card_wake_sdio_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Do not unnecessarily enable card detect wakeup in the cases that the card
is not removable or a GPIO is used for card detect.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that tuning no longer leaves the Buffer Read Enable bit set (refer
intel_execute_tuning()), glk_cqe_enable() is no longer needed. Get rid of
it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not sure why it was there in the first place, but it's
obviously useless check, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cur_slot and num_slots has been removed from struct dw_mci in 42f989c002.
Unfortunately, inline documentation was not updated so far.
Fix @lock field documentation in Locking section.
Move @mrq field of struct dw_mci_slot mention closer to it
description, so no one could miss this slightest detail.
Couple of code style fixes as a bonus.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang reports a compile warning:
drivers/mmc/host/dw_mmc.c:2124:5: warning: Value stored to 'prev_state'
is never read
By checking the code, prev_state and state assignment for
STATE_SENDING_CMD is indeed never used after jumping to unlock tag.
So remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the newly added macro to simply to the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO_MASK_CMD is properly enabled in tmio_mmc_start_command().
We have no reason to set it up in tmio_mmc_host_probe(). (If we
really wanted to set it in the probe, we would have to do likewise
when resuming.)
Even worse, the following code is extremely confusing:
_host->sdcard_irq_mask &= ~irq_mask;
The logic is opposite between "->sdcard_irq_mask" and "irq_mask".
The intention is not clear at a glance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, force_pio is cleared when the driver exits. Then, it
resulted in clearing it in multiple places since MMC drivers in
general have multiple exit points.
tmio_mmc_reset_work - bails out on timeout
tmio_process_mrq - error out when it cannot send a command
tmio_mmc_finish_request - successful exit
This is error-prone since we may miss to cover all bail-out points.
To simplify the code, the data structure should be initialized just
before used since we have a single entrance. force_pio is only used
for data transfer, so tmio_mmc_start_data() will be a suitable place
to clear this flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As far as I tested the IP on UniPhier SoCs, TMIO_STAT_{RXRDY,TXRQ}
are asserted for DMA mode as well as for PIO. I need to disable the
those IRQs in dma_ops->start hook, otherwise the DMA transfer fails
with the following error message:
PIO IRQ in DMA mode!
Renesas chips are the same cases since I see their dma_ops->start
hooks explicitly clear TMIO_STAT_{RXRDY,TXRQ} (with nice comment!).
If we do this sanity check in TMIO MMC core, RXRDY/TXRQ handling
should be entirely moved to the core. tmio_mmc_cmd_irq() will
be a suitable place to disable them.
The probe function sets TMIO_MASK_{READOP,WRITEOP} but this is odd.
/* Unmask the IRQs we want to know about */
if (!_host->chan_rx)
irq_mask |= TMIO_MASK_READOP;
if (!_host->chan_tx)
irq_mask |= TMIO_MASK_WRITEOP;
At this point, _host->{chan_rx,chan_tx} are _always_ NULL because
tmio_mmc_request_dma() is called after this code. Consequently,
TMIO_MASK_{READOP,WRITEOP} are set here whether DMA is used or not.
Remove this pointless code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The TMIO mmc cannot detect the card insertion in native_hotplug mode
if the driver is probed without a card inserted.
The reason is obvious; all IRQs are disabled by tmio_mmc_host_probe(),
as follows:
tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL);
The card event IRQs are first enabled by tmio_mmc_start_command() as
follows:
if (!host->native_hotplug)
irq_mask &= ~(TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
tmio_mmc_enable_mmc_irqs(host, irq_mask);
If the driver is probed without a card, tmio_mmc_start_command() is
never called in the first place. So, the card is never detected.
The card event IRQs must be enabled in probe/resume functions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
A card detect GPIO is set up only for platforms with "cd-gpios"
DT property or TMIO_MMC_USE_GPIO_CD flag. However, the driver
core always uses mmc_gpio_get_cd, which just fails with -ENOSYS
if ctx->cd_gpio is unset.
The bit 5 of the status register provides the current signal level
of the CD line. Allow to use it if the GPIO is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The commit 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
and commit 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
made changes, which cause multiply overflow for 32-bit systems. The broken
timeout calculations leads to unexpected ETIMEDOUT errors and causes
stacktrace splat (such as below) during normal data exchange with SD-card.
| Running : 4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1
| - Info: Finished target initialization.
| mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd
| response 0x900, card status 0x0
DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so
code gets compiled on all 32-bit platforms as opposed to usage of
DIV_ROUND_UP when we may only compile stuff on a very few arches.
Lets cast this multiply to u64 type to prevent the overflow.
Fixes: 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
Fixes: 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.14
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This property is equivalent to "disable-wp" defined in
Documentation/devicetree/bindings/mmc/mmc.txt
The TMIO MMC core calls mmc_of_parse(), and it sets
MMC_CAP2_NO_WRITE_PROTECT if "disable-wp" property is present.
We do not need a vendor-specific property to do the same thing.
Let's remove the description from the dt-binding to prevent new boards
from using it.
I am keeping the driver code for existing DT files, but added
comments that this is deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The use of this flag has been replaced with MMC_CAP2_NO_WRITE_PROTECT.
No platform defines this flag any more. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
"toshiba,mmc-wrprotect-disable" at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
The flag is propagated as follows:
renesas_sdhi_of_data::capabilities2
-> tmio_mmc_data::capabilities2
-> mmc_host::caps2
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
TMIO_MMC_WRPROTECT_DISABLE at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to set the IODELAY values depending on the various MMC
modes using the pinctrl APIs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i802 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
during the tuning procedure and it has to be disabled during the
tuning procedure Implement workaround for Errata i802 here..
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC tuning procedure is required to support SD card
UHS1-SDR104 mode and EMMC HS200 mode.
SDR104/HS200 DLL Tuning Procedure for AM572x platform is mentioned
in Figure 25-51. SDR104/HS200 DLL Tuning Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
The tuning function sdhci_omap_execute_tuning() will only be
called by the MMC/SD core if the corresponding speed modes
are supported by the OMAP silicon which is set in the mmc
host "caps" field.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UHS-1 DDR50 and MMC DDR52 mode require DDR bit to be
set in the configuration register (MMCHS_CON). Add
sdhci-omap specific set_uhs_signaling ops to set
this bit. Also while setting the UHSMS bit, clock should be
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add card_busy host ops in sdhci_omap to check card busy status.
The voltage switching sequence for AM572x platform is mentioned
in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON
should also be set after switching to 1.8v which is also taken
care in the card_busy ops.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Updating 'power_mode' in sdhci_omap_init_74_clocks results in
'power_mode' never updated to MMC_POWER_OFF during card
removal. This results in initialization sequence not sent to the
card during re-insertion.
Fix it here by adding sdhci_omap_set_power_mode to update power_mode.
This function can also be used later to perform operations that
are specific to a power mode (e.g, disable tuning during power off).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 361c7fe9b0 ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The optional DT parameter max-frequency could init the max bus frequency.
So take care of this, before setting the max bus frequency.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 0a44697627.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJafl86AAoJED2LAQed4NsGrBEP/23mRl+8dSYkTmlczP7stZHL
tGkMQIOj85usPV4JIxYHgge6XhU0CBFXNGnDnxGeNEtwnBr5QQNxuS2nPh7rHJIN
zX5rX/vwO9lzn2FFEdKrk8bito1IgnUHUvN/d0ikPWzY7GaMy6WrIWgyThllsLNE
W7hp3cpUQOhLL9PKXwglZ/oS4iTpEs0DwN93UXU7cp7zyRa0XtFfPf7/IJ2KY+Yl
a2TEsUuZ/slJoxLhacr6+TBAgqUyewWIs0nAGdjP2EVlSjxZJQYFEQq4KnLUO2gV
wLHH2snsZSBDfPDp0M9OOb737HE17NRmuLjWxUZZOMFz8tvfUT1454zhVAN2OtSQ
cP0RqVRrFiS721oxacZpAxKFrd7o4ugUHpftJMPQAq70T9JFFbapfCLvd+OblOb/
CWmDOOR37tvop5OCuaqaSMq7a+ZQt2cO5fogiEDdnjZkk2AH5GgsAHJIrl7hH4OT
P9UMcxaWSGbutdVkM4cMUmYMuAJjiFhx1fiD+hevB1KvemXRXrqhCb0wV+GRdcoU
MXGvOGVw5WyF/vFdjpjkY7KeCgpU3BTWH3pFC2a5vUCDqgD8yndwFghJMDfSjl6d
46DIqknyveq234GK/Yz5khlbY094yL8JrJU2duva/9fGV86tgOr29xgMK28Lpyh8
AYRGO9XgmehZrEHcAQ57
=jy5l
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
The Meson GX MMC driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h being pulled in by the device.h header
implicitly.
Include the header explicitly to avoid the build failure.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blank help texts are probably either a typo, a Kconfig misunderstanding,
or some kind of half-committing to adding a help text (in which case a
TODO comment would be clearer, if the help text really can't be added
right away).
Best to remove them, IMO.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.
SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.
Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.
These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.
This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.
When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.
dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Tested-by: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
specially highlighted.
First, we have converted the MMC block device from using the legacy blk
interface into using the modern blkmq interface. Not only do we get all the
nice effects from using blkmq, but it also means that new fresh nice code
replaces old rusty code. Great news to everybody that cares about MMC/SD!
It should also be noted that converting to blkmq has not been trivial, mostly
because of that we have been carrying too much of MMC specific optimizations
for the I/O request path, rather than striving to move these to the generic blk
layer. Hopefully we won't be doing that mistake, ever again.
Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro), who both
have been working on this for quite some time!
Second, on top of the blkmq deployment, we have enabled full support the eMMC
command queuing feature, introduced in the eMMC v.5.1 spec. This also includes
an implementation of a host driver library, supporting the corresponding CQHCI
HW. Ideally, those controllers that supports CQHCI should only need some minor
adaptations to make this play.
So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan driver
used on Rockchip RK3399, have enabled support for eMMC command queueing.
Worth to highlight is also that, implementing the eMMC command queuing support
has been a collaborative effort, as several people from Codeaurora, Rockchip,
Intel and Linaro have been involved. However, the work has been driven by
Adrian Hunter (Intel).
In some shadow of the above, here are the rest of the highlights:
MMC core:
- Don't remove non-removable cards during system suspend
- Add a slot-gpio helper to check capability of GPIO WP detection
MMC host:
- sdhci: Cleanups and improvements of some wakeup related code
- sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
- sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
- sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
- sdhci_f_sdh30: Add ACPI support
- sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
- sdhci-of-esdhc: A few minor fixes
- mmci: Add support for new STM32 variant
- renesas_sdhi: enable R-Car D3 (r8a77995) support
- tmio/renesas_sdhi: Re-structuring, cleanups and modernizations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kUV+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"There are two major achievements for MMC in this release, which
deserves to be specially highlighted.
First, we have converted the MMC block device from using the legacy
blk interface into using the modern blkmq interface. Not only do we
get all the nice effects from using blkmq, but it also means that new
fresh nice code replaces old rusty code. Great news to everybody that
cares about MMC/SD!
It should also be noted that converting to blkmq has not been trivial,
mostly because of that we have been carrying too much of MMC specific
optimizations for the I/O request path, rather than striving to move
these to the generic blk layer. Hopefully we won't be doing that
mistake, ever again.
Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro),
who both have been working on this for quite some time!
Second, on top of the blkmq deployment, we have enabled full support
the eMMC command queuing feature, introduced in the eMMC v.5.1 spec.
This also includes an implementation of a host driver library,
supporting the corresponding CQHCI HW. Ideally, those controllers that
supports CQHCI should only need some minor adaptations to make this
play.
So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan
driver used on Rockchip RK3399, have enabled support for eMMC command
queueing.
Worth to highlight is also that, implementing the eMMC command queuing
support has been a collaborative effort, as several people from
Codeaurora, Rockchip, Intel and Linaro have been involved. However,
the work has been driven by Adrian Hunter (Intel).
In some shadow of the above, here are the rest of the highlights:
MMC core:
- Don't remove non-removable cards during system suspend
- Add a slot-gpio helper to check capability of GPIO WP detection
MMC host:
- sdhci: Cleanups and improvements of some wakeup related code
- sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
- sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
- sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
- sdhci_f_sdh30: Add ACPI support
- sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
- sdhci-of-esdhc: A few minor fixes
- mmci: Add support for new STM32 variant
- renesas_sdhi: enable R-Car D3 (r8a77995) support
- tmio/renesas_sdhi: Re-structuring, cleanups and modernizations"
* tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (96 commits)
mmc: mmci: fix error return code in mmci_probe()
mmc: davinci: suppress error message on EPROBE_DEFER
mmc: davinci: dont' use module_platform_driver_probe()
mmc: tmio: hide unused tmio_mmc_clk_disable/tmio_mmc_clk_enable functions
mmc: mmci: Add STM32 variant
mmc: mmci: Add support for setting pad type via pinctrl
mmc: mmci: Don't pretend all variants to have OPENDRAIN bit
mmc: mmci: Don't pretend all variants to have MCI_STARBITERR flag
mmc: mmci: Don't pretend all variants to have MMCIMASK1 register
mmc: tmio: refactor .get_ro hook
mmc: slot-gpio: add a helper to check capability of GPIO WP detection
mmc: tmio: remove dma_ops from tmio_mmc_host_probe() argument
mmc: tmio: move {tmio_}mmc_of_parse() to tmio_mmc_host_alloc()
mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()
mmc: tmio: ioremap memory resource in tmio_mmc_host_alloc()
mmc: sh_mmcif: remove redundant initialization of 'opc'
mmc: sdhci: Rework sdhci_enable_irq_wakeups()
mmc: sdhci: Handle failure of enable_irq_wake()
mmc: sdhci: Stop exporting sdhci_enable_irq_wakeups()
mmc: sdhci-pci: Use device wakeup capability to determine MMC_PM_WAKE_SDIO_IRQ capability
...
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f9bb304ce8 ("mmc: mmci: Add support for setting pad type via pinctrl")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This suppresses printing an error message during probe of the TI DaVinci
MMC driver when the error is EPROBE_DEFER.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This changes module_platform_driver_probe() to module_platform_driver()
in the TI DaVinci MMC driver.
On device tree systems, we can get a -EPROBE_DEFER when using a pinmux
for the CD GPIO, which results in the driver never loading because
module_platform_driver_probe() prevents it from being re-probed.
So, we replace module_platform_driver_probe() with
module_platform_driver() and removed the __init attributes accordingly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_PM is disabled, we get a warning about the clock handling
being unused:
drivers/mmc/host/tmio_mmc_core.c:937:13: error: 'tmio_mmc_clk_disable' defined but not used [-Werror=unused-function]
static void tmio_mmc_clk_disable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/tmio_mmc_core.c:929:12: error: 'tmio_mmc_clk_enable' defined but not used [-Werror=unused-function]
static int tmio_mmc_clk_enable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~
As the clock handling is now done elsewhere, this is only used when
power management is enabled. We could make the functions as __maybe_unused,
but since there is already an #ifdef section, it seems easier to move
the helpers closer to their callers.
Fixes: b21fc29438 ("mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STM32F4 and STM32F7 MCUs has a SDIO controller that looks like
an ARM PL810.
This patch adds the STM32 variant so that mmci driver supports it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If variant hasn't the control bit to switch pads in opendrain mode,
we can achieve the same result by asking to the pinmux driver to
configure pins for us.
This patch make the mmci driver able to do this whenever needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for supporting STM32 variant which doesn't
have opendrain bit in MMCIPOWER register.
ST others variant (u300, nomadik and ux500) uses MCI_OD bit whereas
others variants uses MCI_ROD bit.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for supporting the STM32 variant that
has no such bit in the status register.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two mask registers are used in order to select which events have to
actually generate an interrupt on each IRQ line.
It seems that in the single-IRQ case it's assumed that the IRQs lines
are simply OR-ed, while the two mask registers are still present. The
driver still programs the two mask registers separately.
However the STM32 variant has only one IRQ, and also has only one mask
register.
This patch prepares for STM32 variant support by making the driver using
only one mask register.
This patch also optimize the MMCIMASK1 mask usage by caching it into
host->mask1_reg which avoid to read it into mmci_irq().
Tested only on STM32 variant. RFT for variants other than STM32
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This IP provides the write protect signal level in the status
register, but it is also possible to use GPIO for WP. They are
exclusive, so it is not efficient to call mmc_gpio_get_ro() every
time from tmio_mmc_get_ro() if we know gpio_ro is not used.
Check the capability of gpio_ro just once in the probe function,
then set mmc_gpio_get_ro to .get_ro if it is the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers need to set up various struct members for tmio_mmc_host before
calling tmio_mmc_host_probe(). Do likewise for host->dma_ops instead
of passing it as a function argument.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() parses various DT properties and sets capability flags
accordingly. However, drivers have no chance to run platform init
code depending on such flags because mmc_of_parse() is called from
tmio_mmc_host_probe().
Move mmc_of_parse() to tmio_mmc_host_alloc() so that drivers can
handle capabilities before mmc_add_host(). Move tmio_mmc_of_parse()
likewise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock is enabled in the tmio_mmc_host_probe(). It also prevents
drivers from performing platform-specific settings before mmc_add_host()
because the register access generally requires a clock.
Enable/disable the clock in drivers' probe/remove. Also, I passed
tmio_mmc_data to tmio_mmc_host_alloc() because renesas_sdhi_clk_enable()
needs it to get the private data from tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register region is ioremap'ed in the tmio_mmc_host_probe(), i.e.
drivers cannot get access to the hardware before mmc_add_host().
Actually, renesas_sdhi_core.c reads out the CTL_VERSION register to
complete the platform-specific settings. However, at this point,
the MMC host is already running.
Move the register ioremap to tmio_mmc_host_alloc() so that drivers
can perform platform-specific settings between tmio_mmc_host_alloc()
and tmio_mmc_host_probe().
I changed tmio_mmc_host_alloc() to return an error pointer to
propagate the return code from devm_ioremap_resource().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable opc is initialized with a value that is never read, opc
is later re-assigned a newer value, hence the initialization can
be removed.
Cleans up clang warning:
drivers/mmc/host/sh_mmcif.c:919:6: warning: Value stored to 'opc'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding more conditions for whether IRQ wakeup is
enabled, rework sdhci_enable_irq_wakeups() so that needed bits are added
instead of adding them all and then removing the unneeded bits.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_enable_irq_wakeups() is a local function, change it to
return whether the IRQ wakeup was successfully enabled. This is in
preparation for adding more conditions for whether IRQ wakeup is enabled.
Note it is assumed, for SDHCI devices, that suspend is more important than
wakeup, so we continue to suspend regardless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that it is not being used by any drivers, stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PCI and ACPI determine if a device is wakeup capable, so use that to
determine the MMC_PM_WAKE_SDIO_IRQ capability correctly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_enable_irq_wakeups() is already called by sdhci_suspend_host() so
sdhci-pci should not need to call it. However sdhci_suspend_host() only
calls it if wakeups are enabled, and sdhci-pci does not enable them until
after calling sdhci_suspend_host(). So move the calls to
sdhci_pci_init_wakeup() before calling sdhci_suspend_host(), and
stop calling sdhci_enable_irq_wakeups(). That results in some
simplification because sdhci_pci_suspend_host() and
__sdhci_pci_suspend_host() no longer need to be separate functions.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CQHCI initialization and implement CQHCI operations for Arasan
SDHCI variant host, namely arasan,sdhci-5.1, which is used by Rockchip
RK3399 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.
This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[ 1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[ 2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[ 12.645056] mmc1: Timeout waiting for hardware interrupt.
[ 12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 12.656921] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001201
[ 12.663366] mmc1: sdhci: Blk size: 0x00000004 | Blk cnt: 0x00000000
[ 12.669813] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
[ 12.676258] mmc1: sdhci: Present: 0x01f8028f | Host ctl: 0x00000013
[ 12.682703] mmc1: sdhci: Power: 0x00000002 | Blk gap: 0x00000000
[ 12.689148] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000003f
[ 12.695594] mmc1: sdhci: Timeout: 0x0000008e | Int stat: 0x00000000
[ 12.702039] mmc1: sdhci: Int enab: 0x107f004b | Sig enab: 0x107f004b
[ 12.708485] mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00001201
[ 12.714930] mmc1: sdhci: Caps: 0x07eb0000 | Caps_1: 0x08100810
[ 12.721375] mmc1: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000
[ 12.727821] mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000
[ 12.734265] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[ 12.745157] mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0xc8049200
[ 12.751601] mmc1: sdhci: ============================================
[ 12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[ 12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[ 12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[ 12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[ 12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Wladimir J. van der Laan <laanwj@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To use a GPIO line for card detection, TMIO_MMC_USE_GPIO_CD is set
by a legacy board (arch/sh/boards/mach-ecovec24).
For DT platforms, the "cd-gpios" property is a legitimate way for that
in case the IP-builtin card detection can not be used for some reason.
mmc_of_parse() calls mmc_gpiod_request_cd() to set up ctx->cd_gpio if
the "cd-gpios" property is specified.
To cater to both cases, mmc_can_gpio_cd() is a correct way to check
which card detection logic is used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Intel Edison the Broadcom Wi-Fi card, which is connected to SDIO,
requires 2.0v, while the host, according to Intel Merrifield TRM,
supports 1.8v supply only.
The card announces itself as
mmc2: new ultra high speed DDR50 SDIO card at address 0001
Introduce a custom OCR mask for SDIO host controller on Intel Merrifield
and add a special case to sdhci_set_power_noreg() to override 2.0v supply
by enforcing 1.8v power choice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The inconsistent NULL checking in this function causes static checker
warnings.
drivers/mmc/host/renesas_sdhi_sys_dmac.c:360 renesas_sdhi_sys_dmac_issue_tasklet_fn()
error: we previously assumed 'host' could be null (see line 351)
On reviewing this code, "host" can't ever be NULL so we can just remove
the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Fujitsu SDH30 SDHCI controller may be described as a SCX0002 ACPI
device on ACPI platforms incorporating the Socionext SynQuacer SoC.
Given that mmc_of_parse() has already been made ACPI/DT agnostic,
making the SDH30 driver ACPI capable is actually rather simple:
all we need to do is make the call to sdhci_get_of_property() [which
does not set any properties we care about] and the clock handling
dependent on whether we are dealing with a DT device, and exposing
the ACPI id via the platform_driver struct and the module metadata.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc clock can be stopped during runtime suspend and restart during runtime
resume if the sdio irq is not enabled. Stop sdio clock reduce EMI of
the device when the bus is not in use.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
runtime_resume() should re-enable the clocks in reverse order comparing with
runtime_suspend()
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to return in case of error even if the actual implementation
of sdhci_runtime_suspend_host always return 0. We don't want to
power down the clock and the assuption is that the sdhci_runtime_suspend_host
always let the system consistent in case of failure
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Arasan Controller is based on a FPGA platform and has integrated phy
with specific registers used during initialization and
management of different modes. The phy and the controller are integrated
and registers are very specific to Arasan.
Arasan being an IP provider, licenses these IPs to various companies for
integration of IP in custom SOCs. The custom SOCs define own register
map depending on how bits are tied inside the SOC for phy registers,
depending on SOC memory plan and hence will require own platform drivers.
If more details on phy registers are required, an interface document is
hosted at https://arasan.com/NF/eMMC5.1 PHY Programming in Linux.pdf.
Signed-off-by: Atul Garg <agarg@arasan.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The global array clashes with a newly added symbol of the same name:
drivers/staging/ccree/cc_debugfs.o:(.data+0x0): multiple definition of `debug_regs'
drivers/mmc/host/s3cmci.o:(.data+0x70): first defined here
We should fix both, this one addresses the s3cmci driver by removing
the symbol from the global namespace. While at it, this separates
the declaration from the type definition and makes the variable const.
Fixes: 9bdd203b4d ("s3cmci: add debugfs support for examining driver and hardware state")
Fixes: b3ec9a6736 ("staging: ccree: staging: ccree: replace sysfs by debugfs interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because we started using io*_rep accessors previously because they are
more widely defined across architectures, let's be consistent and use
this family for all accessor wrappers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to SD spec 3.00 3.6.1 signal voltage switch
procedure step 6~8,
(6) Set 1.8V Signal Enable in the Host Control 2 register.
(7) Wait 5ms. 1.8V voltage regulator shall be stable within this period.
(8) If 1.8V Signal Enable is cleared by Host Controller, go to step (12).
Host should wait 5ms after set 1.8V signal enable bit in
Host Control 2 register and check if 1.8V is stable or not.
But current code checks this bit right after set it.
On some platforms with xenon controller found the bit is
cleared right away and host reports "1.8V regulator output
did not became stable" and 5ms delay can help.
Implement voltage_switch callback for xenon controller to add 5ms
delay to make sure the 1.8V signal enable bit is set by controller.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sane values for bus_shift are:
0 - for 16 bit bus
1 - for 32 bit bus
2 - for 64 bit bus
"unsigned long" is too much.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_host has "scc_tappos", but in fact, it is Renesas
private data. Move it to renesas_sdhi.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_host has "dma_dataend" and "dma_complete", but in fact,
they are Renesas private data. Move them to renesas_sdhi.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_dma looks like TMIO core data, but in fact, Renesas
private data. Move it to renesas_sdhi.h (probably, it is better to
rename it to renesas_sdhi_dma, or squash it into struct renesas_sdhi).
I also moved struct renesas_sdhi and host_to_priv() to that header
because they are necessary to convert the tmio_mmc_host pointer into
the renesas_sdhi pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC_DRV_OP_GET_EXT_CSD request completes successfully, then
ext_csd must be freed, but in one case it was not. Fix that.
Signed-off-by: Liu Changcheng <changcheng.liu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers do not need to call mmc_gpiod_request_cd_irq() explicitly
because mmc_start_host() calls it. To make it work, cd_gpio must
be set before mmc_add_host().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers can set any mmc_host_ops hooks between tmio_mmc_host_alloc()
and tmio_mmc_host_probe(). Remove duplicated hooks in tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, tmio_mmc_ops is static data and tmio_mmc_host_probe()
updates some hooks in the static data. This is a problem when
two or more instances call tmio_mmc_host_probe() and each of them
requests to use its own card_busy/start_signal_voltage_switch.
We can borrow a solution from sdhci_alloc_host(). Copy the whole
ops structure to host->mmc_host_ops, then override the hooks in
malloc'ed data. Constify tmio_mmc_ops since it is now a template
ops used by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMIO core misses to call request_mem_region().
devm_ioremap_resource() takes care of it and makes the code cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The remove, suspend, resume hooks need to get tmio_mmc_host. It is
tedious to call mmc_priv() to convert mmc_host to tmio_mmc_host.
We can directly set tmio_mmc_host to driver data.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ARCH_RENESAS is a stronger condition than (ARM || ARM64).
If ARCH_RENESAS is enabled, (ARM || ARM64) is met as well.
What is worse, the first depends on line prevents COMPILE_TEST from
enabling this driver. It should be removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all archs define reads* and writes*. Switch to ioread*_rep and
friends which is defined everywhere, so we can enable COMPILE_TEST after
that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following error occurs when loading renesas_sdhi_core.c module,
so add MODULE_LICENSE("GPL v2").
renesas_sdhi_core: module license 'unspecified' taints kernel.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Fixes: 9d08428afb ("mmc: renesas-sdhi: make renesas_sdhi_sys_dmac main module file")
Cc: <stable@vger.kernel.org> # v4.13+
[Shimoda: Added Fixes tag and Cc to the stable ML]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The description in the Makefile is odd. Fix the CONFIG selection
in a cleaner way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel DSM function 8 has been used to identify transfer modes that are not
working on some CHT boards. Add support for that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a ->setup_host() callback so that device-specific changes can be made
to the mmc host controller before it is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL. The callers are not expecting that and will have a NULL pointer
dereference.
Fixes: 41e3efd07d ("mmc: block: Simplify cleaning up the queue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Absence of parentheses is not affecting current code, but ensure macro
parameters are wrapped in parentheses.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.
Fixes: 9d4579a85c ("mmc: mmc_test: Disable Command Queue while mmc_test is used")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
Commands during non-blocking read - use Set Block Count (CMD23)
Commands during non-blocking write - use Set Block Count (CMD23)
mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().
Fixes: cb39f61e9b ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch supports HS400 for AMD upcoming emmc 5.0 controller.The
HS400 and HS200 mode requires hardware work around also. This patch
adds the quirks for the same.
Signed-off-by: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power register needs to have a valid voltage set
even when the power supply is managed by an external regulator.
Signed-off-by: Milan Stevanovic <milan.o.stevanovic@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function mmc_cqe_issue_type is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/mmc/core/queue.c:62:21: warning: symbol 'mmc_cqe_issue_type'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/core/block.c:2106:9-10: WARNING: return of 0/1 in function 'mmc_blk_status_error' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes:7eb43d537166 ("mmc: block: blk-mq: Stop using legacy recovery")
CC: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver's blk-mq paths do not use mmc_start_areq(). In order to
remove mmc_start_areq() entirely, start by removing it from mmc_test.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
There are only a few things the recovery needs to do. Primarily, it just
needs to:
Determine the number of bytes transferred
Get the card back to transfer state
Determine whether to retry
There are also a couple of additional features:
Reset the card before the last retry
Read one sector at a time
The legacy code spent much effort analyzing command errors, but commands
fail fast, so it is simpler just to give all command errors the same number
of retries.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Set a 10 second timeout for polling write request busy state. Note, mmc
core is setting a 3 second timeout for SD cards, and SDHCI has long had a
10 second software timer to timeout the whole request, so 10 seconds should
be ample.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
According to the specification, total access time is derived from both TAAC
and NSAC, which means the timeout should add both timeout_ns and
timeout_clks. Host drivers do that, so make the block driver do that too.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
The card is required to return to transfer state. Since that is the state
required to start another transfer, check for that state instead of
programming state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Pedantically, ensure the status is checked for the last time after the full
timeout has passed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Check error bits and save the exception bit when polling card busy.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make card_busy_detect() accumulate all response error bits. Later patches
will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Recovery is simpler to understand if it is only used for errors. Create a
separate function for card polling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
For blk-mq, add support for completing requests directly in the ->done
callback. That means that error handling and urgent background operations
must be handled by recovery_work in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds CMDQ support for command-queue compatible
hosts.
Command queue is added in eMMC-5.1 specification. This
enables the controller to process upto 32 requests at
a time.
Adrian Hunter contributed renaming to cqhci, recovery, suspend
and resume, cqhci_off, cqhci_wait_for_idle, and external timeout
handling.
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Add CQE support to the block driver, including:
- optionally using DCMD for flush requests
- "manually" issuing discard requests
- issuing read / write requests to the CQE
- supporting block-layer timeouts
- handling recovery
- supporting re-tuning
CQE offers 25% - 50% better random multi-threaded I/O. There is a slight
(e.g. 2%) drop in sequential read speed but no observable change to sequential
write.
CQE automatically sends the commands to complete requests. However it only
supports reads / writes and so-called "direct commands" (DCMD). Furthermore
DCMD is limited to one command at a time, but discards require 3 commands.
That makes issuing discards through CQE very awkward, but some CQE's don't
support DCMD anyway. So for discards, the existing non-CQE approach is
taken, where the mmc core code issues the 3 commands one at a time i.e.
mmc_erase(). Where DCMD is used, is for issuing flushes.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Define and use a blk-mq queue. Discards and flushes are processed
synchronously, but reads and writes asynchronously. In order to support
slow DMA unmapping, DMA unmapping is not done until after the next request
is started. That means the request is not completed until then. If there is
no next request then the completion is done by queued work.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Add error-handling comments to explain what would also be done for blk-mq
if it used the legacy error-handling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make mmc_pre_req() and mmc_post_req() available to the card drivers. Later
patches will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Use blk_cleanup_queue() to shutdown the queue when the driver is removed,
and instead get an extra reference to the queue to prevent the queue being
freed before the final mmc_blk_put().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
mmc_cleanup_queue() is not used by a different module. Do not export it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
It had an U+FFFD: not a corrupted character but a literal well-formed
replacement marker.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a few udelay() left which are in a range that they should be
usleep_range() these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Documentation/timers/timers-howto.txt recommends to use usleep_range for
delays 1-20ms. Let's adhere to it. No need for messing with HZ and still
do busy looping these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not efficient to call gpiod_to_irq() regardless the flag, then
ignore the returned irq if MMC_CAP_NEEDS_POLL.
Move gpiod_to_irq() after the MMC_CAP_NEEDS_POLL check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the latest version of parsing the new eMMC bindings was moved from
core.c to mmc.c, it was overlooked that drv_type could be used
uninitialized. Fix it!
Fixes: 6186d06c51 ("mmc: parse new binding for eMMC fixed driver type")
Reported-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=13VJ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full"
* tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: prepend 0x to OCR entry in sysfs
mmc: core: prepend 0x to pre_eol_info entry in sysfs
mmc: sdhci: Avoid swiotlb buffer being full
mmc: sdhci-msm: Optionally wait for signal level changes
mmc: block: Ensure that debugfs files are removed
mmc: core: Do not leave the block driver in a suspended state
mmc: block: Check return value of blk_get_request()
mmc: block: Fix missing blk_put_request()
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The sysfs entry "ocr" was missing the 0x prefix to identify it as hex
formatted.
Fixes: 5fb06af7a3 ("mmc: core: Extend sysfs with OCR register")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.8+
[Ulf: Amended change to also cover SD-cards]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sysfs entry "pre_eol_info" was missing the 0x prefix to identify it
as hex formatted.
Fixes: 46bc5c408e ("mmc: core: Export device lifetime information through sysfs")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit de3ee99b09 ("mmc: Delete bounce buffer handling") deletes the
bounce buffer handling, but also causes the max_req_size for sdhci to be
increased, in case when max_segs == 1. This causes errors for sdhci-pci
Ricoh variant, about the swiotlb buffer to become full.
Fix the issue, by taking IO_TLB_SEGSIZE and IO_TLB_SHIFT into account when
deciding the max_req_size for sdhci.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Not all instances of the SDCC core supports changing signal voltage and
as such will not generate a power interrupt when the software attempts
to change the voltage. This results in probing the eMMC on some devices
to take over 2 minutes.
Check that the SWITCHABLE_SIGNALING_VOLTAGE bit in MCI_GENERICS is set
before waiting for the power interrupt.
Cc: Sahitya Tummala <stummala@codeaurora.org>
Cc: Vijay Viswanath <vviswana@codeaurora.org>
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card is not necessarily being removed, but the debugfs files must be
removed when the driver is removed, otherwise they will continue to exist
after unbinding the card from the driver. e.g.
# echo "mmc1:0001" > /sys/bus/mmc/drivers/mmcblk/unbind
# cat /sys/kernel/debug/mmc1/mmc1\:0001/ext_csd
[ 173.634584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
[ 173.643356] IP: mmc_ext_csd_open+0x5e/0x170
A complication is that the debugfs_root may have already been removed, so
check for that too.
Fixes: 627c3ccfb4 ("mmc: debugfs: Move block debugfs into block module")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver must be resumed if the mmc bus fails to suspend the card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
The Socionext SynQuacer SoC inherits this IP from Fujitsu, but
requires the F_SDH30_CMD_DAT_DELAY bit to be set in the
F_SDH30_ESD_CONTROL control register. So set this bit if the
DT node has the 'fujitsu,cmd-dat-delay-select' property.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As documented in Documentation/timers/timers-howto.txt
as follows, replace msleep() with usleep_range().
msleep(1~20) may not do what the caller intends, and
will often sleep longer (~20 ms actual sleep for any
value given in the 1~20ms range). In many cases this
is not the desired behavior.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent CTO timer introduced in commit 03de19212e ("mmc: dw_mmc:
introduce timer for broken command transfer over scheme") was causing
observable problems due to race conditions. Previous patches have
fixed those race conditions.
It can be observed that these same race conditions ought to be
theoretically possible with the DTO timer too though they are
massively less likely to happen because the data timeout is always set
to 0xffffff right now. That means even at a 200 MHz card clock we
were arming the DTO timer for 94 ms:
>>> (0xffffff * 1000. / 200000000) + 10
93.886075
We always also were setting the DTO timer _after_ starting the
transfer, unlike how the old code was seting the CTO timer.
In any case, even though the DTO timer is much less likely to have
races, it still makes sense to add code to handle it _just in case_.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a jump target so that a specific string copy operation is stored
only once at the end of this function implementation.
Replace two calls of the function "strncpy" by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Add a jump target so that a bit of exception handling can be better
reused at the end of this function.
* Adjust condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Allen <allen.lkml@gmail.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel host controllers use an ACPI device-specific method to ensure
correct voltage switching. Fix voltage switch for those, by adding a call
to the DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_acpi_slot structure, then sdhci_acpi_probe() will allocate extra
space for it, and sdhci_acpi_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
data lines have applied to perfer to use rise edge, also need
apply it to cmd line.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enlarge outstanding value to improve read performance
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
some platform(eg.mt2701) does not support "stop clk fix", in
this case, need set correct latch-ck to avoid crc error caused
by stop clock block-internally.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
source clock need an independent cg to control, when doing clk mode
switch, need gate source clock to avoid hw issue(multi-bit sync hw hang)
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2712 supports stop_clk fix and enhance_rx, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bit7 of PATCH_BIT1 has different meaning in new design, to
compatible with previous platform, clear this bit in new
platform.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 supports async fifo & data tune, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
from mt2701, the register of PAD_TUNE has been phased out,
while there is a new register of PAD_TUNE0
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the origin design of hs400_tune_response is for mt8173 because of
mt8173 has a special design. for doing that, we add a new member
"compatible", by now it's only for mt8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like the CTO timeout calculation introduced recently, the DTO
timeout calculation was incorrect. It used "bus_hz" but, as far as I
can tell, it's supposed to use the card clock. Let's account for the
div value, which is documented as 2x the value stored in the register,
or 1 if the register is 0.
NOTE: This was likely not terribly important until commit 16a34574c6
("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is
documented on Rockchip SoCs (the ones that used to define the quirk)
to always be 0 or 1. ...and, in fact, it's documented to only be 1
with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to
everyone it was mostly OK to ignore the DIV value.
I haven't personally observed any problems that are fixed by this
patch but I also haven't tested this anywhere with a DIV other an 0.
AKA: this problem was found simply by code inspection and I have no
failing test cases that are fixed by it. Presumably this could fix
real bugs for someone out there, though.
Fixes: 16a34574c6 ("mmc: dw_mmc: remove the quirks flags")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This attempts to instill a bit of paranoia to the code dealing with
the CTO timer. It's believed that this will make the CTO timer more
robust in the case that we're having very long interrupt latencies.
Note that I originally thought that perhaps this patch was being
overly paranoid and wasn't really needed, but then while I was running
mmc_test on an rk3399 board I saw one instance of the message:
dwmmc_rockchip fe320000.dwmmc: Unexpected interrupt latency
I had debug prints in the CTO timer code and I found that it was
running CMD 13 at the time.
...so even though this patch seems like it might be overly paranoid,
maybe it really isn't?
Presumably the bad interrupt latency experienced was due to the fact
that I had serial console enabled as serial console is typically where
I place blame when I see absurdly large interrupt latencies. In this
particular case there was an (unrelated) printout to the serial
console just before I saw the "Unexpected interrupt latency" printout.
...and actually, I managed to even reproduce the problems by running
"iw mlan0 scan > /dev/null" while mmc_test was running. That not only
does a bunch of PCIe traffic but it also (on my system) outputs some
SELinux log spam.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the commit 03de19212e ("mmc: dw_mmc: introduce timer for broken
command transfer over scheme") we tried to calculate the expected
hardware command timeout value. Unfortunately that calculation isn't
quite correct in all cases. It used "bus_hz" but, as far as I can
tell, it's supposed to use the card clock. Let's account for the div
value, which is documented as 2x the value stored in the register, or
1 if the register is 0.
NOTE: It's not expected that this will actually fix anything important
since the 10 ms margin added by the function will pretty much dwarf
any calculations. The card clock should be 100 kHz at minimum and:
1000 ms/s * (255 * 2) / 100000 Hz.
Gives us 5.1 ms.
...so really the point of this patch is just to make the code more
"correct" in case anyone ever tries to remove the 10 ms buffer.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running with the commit 03de19212e ("mmc: dw_mmc: introduce
timer for broken command transfer over scheme") I found this message
in the log:
Unexpected command timeout, state 7
It turns out that we weren't properly cancelling the new CTO timer in
the case that a voltage switch was done. Let's promote the cancel
into the dw_mci_cmd_interrupt() function to fix this.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 has 12bit clock div, which is not compatible with
mt8135/mt8173. and, some additional features will be added in
mt2701/mt2712, so that need distinguish it by comatibale name.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We keep PCI Ids in sdhci-pci.h and the O2-specific definitions belong in
sdhci-pci-o2micro.c. Move those definitions accordingly. Remove unused O2
definitions in sdhci-pci-core.c. The 3 o2micro external function
declarations might as well be in sdhci-pci.h as well, so move them there
and get rid of sdhci-pci-o2micro.h entirely.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy Intel slot probe functions into one. A single function can be used
because the logic uses hid / uid as necessary to identify devices anyway.
This gets rid of some pointless comments and checks for variables that
cannot possibly be NULL, as well as giving the function a name that
identifies it as specific to Intel controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of acpi_device_uid() instead of open coding.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement fallback compatibility strings for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also, improve readability by listing the shmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
