[Description]
1-add configurable timeout support to aux engine.
2-add timeout support field to dc_caps
3-add reg_key to override extended timeout support
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doing this allows us to split it for diffrent asics. This design will
be helpful for future Asciis.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
use vbios message to call smu for dpm level
also only program dmdata in vsyncflip as HW requirement.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
we found using an active DP to HDMI panel that we weren't validating
dp_pixel_format and hardware timing v_front_porch, causing screen to
blank and/or corrupt while attempting a seamless boot.
[how]
added checks during dc_validate_seamless_boot_timing for these values
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If 48mhz refclk is turned off during PSR, we will have issue doing
link training during detection.
[How]
Get out of PSR before detection
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When diags adds a DWB via a stream update, we calculate MMHUBBUB
paramaters, but dc->current_state has not yet been updated
when the DWB programming happens. This leads to overflow on
high bandwidth tests since the incorrect MMHUBBUB arbitration
parameters are programmed.
[How]
Pass the updated context down to the (enable|update)_writeback functions
so that they can use the correct watermarks when programming MMHUBBUB.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function was mistakenly reverted as part of a legitimate revert. The
old version that was reverted to has bad logic, and is causing situations
where p-state change support is being toggled when it shouldn't be,
resulting in hangs.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Type-c PHY config is not align with dpcd lane count.
When those values didn't match, it cause driver do
link training with 4 lane but phy only can output 2 lane.
The link trainig always fail.
[How]
1. Modify get_max_link_cap function. According DPALT_DP4
to update max lane count.
2. Add dp_mst_verify_link_cap to handle MST case because
we didn't call dp_mst_verify_link_cap for MST case.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
memcmp is vulnerable to regression due to dc_clocks structures not being
organized properly (not "current" clock related structures being at the beginning
of the structure) and causes unnecessary setting of the optimize bit
[how]
add a dcn sepcific comparator, implement for dcn2
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HPD is not suppressed when we lower
clocks on renoir. B/c of this we do link
training when the 48mhz refclk is off, which
will cause ASIC hang.
[how]
Exit optimized power state for detection purpose.
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To compare the crc of the framebuffer data at input of
display pipeline with the crc of the otg, we need to
disable pixel formatter's dynamic expansion feature during
crc capture and keep it enable in the normal operation.
[HOW]
Expose a new interface in DM and dc for pixel formatter
(fmt dynamic bitdepth expansion control). Interface control
the FMT_DYNAMIC_EXP_EN bit, during crc capture keep
it disabled.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update the hdcp display parameter whenever the link is
updated, so the next time there is an update to hdcp we have the
latest display info
[How]
Create a callback, and use this anytime there is a change in the link. This will
be used later by the dm.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This change was made because DTO programming was double-buffered, which
is itself an issue. After deactivating the DTO double buffer, this
change becomes unnecessary.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1. OUTSTANDING_REQUEST_LIMIT update from 0xFF to 0x1F (HW doc update)
2. using memory type to convert UMC's MCLK to Yclk.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.
[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New behaviour will track global updates and update any hw that isn't
related to current stream being updated.
This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When user mode use i2c over aux through ADL or DDI, the function
dal_ddc_service_query_ddc_data will be called. There are two issues.
1. When read/write length > 16byte, current always return false because
the DEFAULT_AUX_MAX_DATA_SIZE != length.
2. When usermode only need to read data through i2c, driver will write
mot = true at the same address and cause i2c sink confused. Therefore
the following read command will get garbage.
[How]
1. Add function dal_dcc_submit_aux_command to handle length > 16 byte.
2. Check read size and write size when query ddc data.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add missing parameters, to make dcn21 compile
without errors
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
call update_bw_bounding_box in DC construct
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Controls display clocks and interfaces with powerplay for
clock and power requirements.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Existing HW Features, HW Diags test requested that the
registers be exposed.
[How]
Add V_TOTAL_MID to existing DC structures.
Make sure values are passed down throughout DC
Add Register definition.
Program the additional registers
Add additional Logic for V_TOTAL_CONTROL.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OS will reserve HW state in UEFI mode.
Driver init_hw reset to RGB which caused HDMI green in YCbCr mode.
read HW blank_color based on acc_mode.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to have the ability to to tell us set degamma on the cursor.
[How]
Pass a flag down to register programming that tells us if the
current surface format needs cursor degamma.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function is not being used, it was left in
when introducing DCN2
[How]
Remove the function
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How] Allocate memory for default page and program memory block addr
into default page addr register.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6c5be4ac63.
This commit was accidentally promoted twice
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During detection link training if a display is disconnected,
the current code will retry 3 times of link training
on disconnected link before giving up.
[how]
Before each retry check for HPD status, only retry
verify link cap when HPD is still high.
Also put a 10ms delay between each retry to improve
the chance of success.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the paremeters are extracted as if dml is calculating
using pipes as we pass them in. in reality, dml internally merges
pipes into planes if pipe split is detected.
This change adds reverse logic to dcn20_calculate_dlg_params so
that the global sync parameters can be correctly extracted for
all the pipes when pipe split is enabled.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are repeated (but guarded) definitions of dwb_src enums. There are
also unused entires. Clean them up.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OGAM_MEM_PWR could stay in light up when driver woke up to update gamma.
either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away.
Easy reproduce after LOW_MEM Power feature enables and resume from S3.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
We want to change where timing is done for alt mode.
Some of the commented out #ifs are needed for DCN20
so we enable them for that case.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to change interface function signature / add an enum
to reflect the available register field values
[How]
- Add a new enum and modify existing functions to use it instead
of bool
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current optc odm interface only accepts 2 opps, we need to
expand this to allow 4 to 1 odm combine.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are currently two interfaces for exactly the same thing:
hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub
version is currently unused past dcn10, largely because the call
from the dcn10 hardware sequencer does not call through the
interface, so the hupb interface was used instead. This is
confusing because of the duplicate code, the unused functions,
and the fact that more that one block currently owns this set
of registers.
[How]
Remove the hubp interface entirely, as well as the register
declarations that are not longer needed because of this. Change
the call site to always call the hubbub version through the
interface. Fix the update_dchub function in dcn20_hubbub.c to
program the correct registers for dcn20.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
At the time DIG FE is connected to its BE, the clocks in OTG are enabled and
PHY will also be set up. When DSC has to be used to fit the stream into the
available bandwidth, without DSC being set DIG could get exposed to the
higer bandwidth it (or link) could handle. This causes the HW to "reject"
video enable setup (the register shows that video enable was attempted, but
the status bit shows it as disabled).
[how]
- Separate DSC setup into DSC register config and DSC PPS SDP setup
- Move most of the DSC setup (register config) to before
dcn10_link_encoder_connect_dig_be_to_fe() is called
- Set up DSC PPS SDP after DIG FE is connected to its BE. This is because
setting DSC PPS SDP before that has no effect.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For seamless boot the init_hw sequence must be split into
actual hardware vs pipes, in order to defer pipe initialization to set mode
and skip of pipe-destructive sequences
[How]
made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit
deleted dcn20 specific versions. This is part 1 of a 2 partimplementation
of seamless boot
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
if dynamic allocation fails during gpio_open, it will cause crash due to
page fault.
[how]
handle allocation when gpio object gets created and prevent from calling
gpio_open if allocation failed
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect. This results in temporary underflow.
[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We require a method to perform synchronous link training.
[HOW]
Sync LT is broken into 3 basic steps.
"Begin" starts the state machine, and resets "preferred" link settings.
"Attempt" will attempt to train the link with a given set of training
parameters.
"End" stops the state machine, and will optionally disable the link phy.
Between "Begin" and "End" DPCD:600h must not be set to "2"
(D3:Powered Down).
Between "Begin" and "End", there may be multiple "Attempts" with different
training parameters.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hdmi data scramble and tmds rate is not reset during pipe reset.
[how]
reset hdmi tmds rate and data scramble on pipe reset
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add to clk_mgr_internal struct, for future use.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some platforms, we need to know SMU version for driver/SMU
compatibility. This change adds that field.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Code to enable DCN20 dynamic metadata feature is duplicated in two places
and was added to DCE110 enable stream.
[How]
Create DCN20 specific enable stream function for clarity, and add a hardware
sequencer function to program dynamic metadata to avoid the duplicate
code.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dual plane dcc programming support for
surfaces.
Removes unions from plane size and dcc params as they
serve no practical purpose only making our code
more convoluted. This results in easy dual plane
dcc and surface size programming.
Temporary diags_dm code is used to handle the interface
change without breaking functionality as a diags change
needs to be applied after this one.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add dc_set_clock
add dc_get_clock
this is for testing and diagnostics to get/set DPPCLK and DISPCLK.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
bypass CM block and MPC ogam for debug or triage use.
[How]
create a new flag cm_bypass_mode, which will set both CM_CONTROL
and MPCC_OGAM_MODE to bypass when set to 1.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds EMP packet programming for enabling dsc with
hdmi. The packets are structured according to VESA HDMI 2.1x
r2 spec, section 10.10.2.2.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For better readability and reusability
[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for OS requirement to set preferred link training
parameters.
[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. With the introduction
of new asics we are required to coordinate vmid use with external
components.
This change converts vmid logic to a DAL module allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
value commited to by HW team is going to be higher
than pre-silicon, and will cause underflow if driver not
updated
[how]
update hardcoded value, update pstate switching logic
to fix case where with long uclk time we won't allow switch
even when we should
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add dwb stereo caps and ver for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Should do full update when display writeback is updated.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dsc adjustment is allowed via stream update sequence.
dsc enablement is only allowed via commit stream sequence.
with the current unified dsc set function, it is hard
to determine which sequence it is called by.
The solution is to decouple dsc adjustment out of enablement
sequence so we can handle them separately.
[how]
decouple dsc adjustment out of enablement.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these enums/structs will be used more generically in the future
so moving it to dc_hw_types and dc_types
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN2.0 LB BPP should be 48 or 16BPC and max cursor width should be 256.
Also use populate_dml_pipes as functions pointer instead of using it directly
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dwb fixes.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1 and DCN2.
In addition, future HW will need to access the HUBPREQ_DEBUG and
CUR_TTU_CNTL0 register for hubp_init. Add that here.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OPTC data format was left at its default value (444) when enabling
ODM combine. This caused issues with FPGA capture.
[How]
Write the OPTC_DATA_FORMAT field when enabling ODM combine.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are ASICs that have fewer DSC engines than pipes, which makes
DSC a resource that should be used only if required.
[how]
Acquire DSC HW resource if required by stream and release when not
required anymore.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when an update programming sequence requires both
front end and back end pipe to be updated synchronously,
a global update lock needs to be set to ensure that
we don't get a frame with only front end update but
not the back end update.
[how]
setup global lock parameters on enable_stream_timing.
enable global lock when pipe_control_lock_global is called.
disable global lock when pipe_control_lock is called.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.
[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 HUBP (Display to data fabric interface
pipe) and HUBBUB (DCN memory HUB interface)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 MPC (Multiple pipe and plane combine)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 OPP (Output Plane Processing)
HW Blocks:
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN2 block,
including programming of the DCCG (Display Controller Clock Generator)
block:
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN2, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After clkmgr rework it gets initialized after resource pool.
The clkmgr is used in resource pool init for xgmi path.
That causes driver crash on Vega20 with xgmi due to NULL deref.
[How]
Move xgmi compensation code to dce121_clk_mgr_construct()
That also allows to make dce121_clock_patch_xgmi_ss_info()
internal static function.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. This makes it
difficult to use vmid use with external components.
This change moves vmid logic outside dc and allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously there were 2 consecutive calls being made to disable
audio stream. The first one disabled the audio stream, and the second
one went through and also tried to disable the audio stream causing
BACO entry issues due to the ASIC appearing busy.
[How]
1. Add a status field to the audio struct which stores enabled/disabled
info
2. In the calls to enable/disable audio stream check if we're already
in the desired state before executing the function
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This macro is specificly used by RV1. Move it to the appropriate
location.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add vtable entries for de-alpha and bias color management interfaces.
Move piece-wise transfer function registers to a helper list for future
reuse.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First step of refactoring clk mgr to better handle different
ways of handling clock operations. Clock operation policies are
soc specific and not just DCN vesion specific. It is not a hw resource,
should not be in the resource pool.
[How]
Change clock manager creation to be based on HW internal ID, rename
clock manager members to be more clear. Move clock manager out of
resource.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To send sdp message immediately from a single slot.
[How]
Modify the generic SDP message interface, and use GSP4 to send immediate
sdp message.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are internal otg params and should be handled as such.
Thich change passes the params as function arguments.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It makes no logical sense being there
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Emulating passive dongle on USB-C port causes issue on some asics.
[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To simply logic for setting DCN specific clocks, we will send
SMU message directly through the VBIOS message box.
[How]
Add new structure in pp_smu to hold functions to set clocks
through vbios message box
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1.
In addition, future HW will need to access the HUBPREQ_DEBUG register
for hubp_init. Add it to the reg list.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new interface now replaces the old interface for all known
configurations.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Replace certain register writes with register sets that overwrites the
the entire register, instead of only a field within the register.
* Add program_watermarks() entry to hubbub vtable. Hook it up to
existing functions that program watermarks.
* Add additional watermark registers.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When DMCU interrupts x86, it leads to undefined phy programming
[how]
expand dmcu interface to support new PHY lock and unlock commands
if DMCU FW doesn't support these commands, they fail silently so its okay
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a fast_validate parameter in dc_validate_global_state for future use
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before it was returning false in the case of failure even though return type should be enum dc_status
[How]
Return DC_FAIL_UNSUPPORTED_1 instead
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clk_mgr is called dccg in dc_state, this change fixes that
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Multiple threads were writing back to one global VBA in DC resulting
in multiple threads overwriting eachother's data
[How]
Add an instance of DML (which contains VBA) to each context and
change all calls that used dc->dml to use context->dml. Created a
seperate copy constructor for linux in a case where there is no
access to DC.
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently only top pipe gets output tf programmed. This change
makes all odm head pipes get output tf programmed.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create a functions to return swizzle types for dml
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pass SDP splitting when setting stream attributes for future use
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create dccg_init and init_clocks for future use
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The resource constructor currently needs num_virtual_links from
init_data but will need access to other items provided by DM.
[HOW]
Pass init_data into DCN create_resource_pool functions.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
existing logic finds "first free pipe from 5 -> 0" to split
this will cause certain sequences to require DC to move
an MPCC from one tree to another, which is unsupported
this leads to blackscreen
to mitigate this problem, we will always try to acquire the
"preferred" pipe, and each pipe has a unique preferred pipe
this means we avoid most of the scenarios where
pipe splitting leads to moving MPCC from one tree
to another
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to add DP SDP message test debugfs to make sdp message test
more convenient and efficient.
[How]
Add a DM accessible SDP interface for custom data.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are issues removing surfaces/streams when odm is active.
This is a step to fix that
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add these interfacese for future use
setup_global_lock()
lock_global()
pipe_control_lock_global()
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
when programming VID_TIMING, we were using the original VESA timing for DP_VIDM/N.
for YCbCr420 or compressed YCbCr422, using half rate as YCbCr444.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to set VID_N_MUL for 4:2:0 cases
[How]
Move setting to enc1_stream_encoder_dp_unblank and
ensure it is also set for non-4:2:0 cases.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
"reference clock" is a very overloaded variable in DC and causes confusion
as there are multiple sources of reference clock, which may be different values
incorrect input values to DML will cause DCHUB to be programmed improperly
and lead to hard to debug underflow issues
[how]
instead of using ref clock everywhere, specify WHICH ref clock:
- xtalin
- dccg refclk
- dchub refclk
these are all distinct values which may not be equal
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
field toggle write is actual field sequence write with the same
field name.
[How]
Use REG_UPDATE_SEQ_2 for both sequence write and toggle.
Rename REG_UPDATE_1by1_3 to REG_UPDATE_SEQ_3.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current reg update and reg set use same functions and
only delta is update reads reg value and call update function.
[How]
Refactor reg update and reg set functions.
1.Implement different functions for reg update and reg set.
2.Wrap same process to a help function, both reg update and
reg set will call it.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cross a TODO item off the list. Cleanup SIGNAL_TYPE_HDMI_FRL, it's
not currently supported.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6bff1cc7780cca2fd2a775aa7b18b789e2a1b608.
[Description]
Revert since this will be checked at CP side.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
UEFI boot usually uses a boot profile that uses higher clocks
and watermark settings.
UEFI boot surface is less optimal, for example it uses linear surface
[How]
Before we finish our seamless boot sequence, keep the clock and
watermark settings from boot.
Update to optimal settings only after first flip away from UEFI
frame buffer.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new aux implementation was not up to spec. This caused us to fail DP
compliance as well as introduced serious delays during system resume.
[How]
Make dce_aux_transfer_raw return the operation result
Make dce_aux_transfer_with_retries delay with udelay instead
of msleep, and only on invalid reply. Also fail on the second
invalid reply, third timeout, or first of any other error
Convert return values to drm error codes in amdgpu_dm
As the two aux transfer functions are now noticeably
different, change the names to better reflect their
functionality and document.
There was one last call to dc_link_aux_transfer that
should have retries, fix that
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In some cases we might need to do a full update. Add a commit_hints
struct for future use
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver need to poll the SURFACE_INUSE register to determine when to
start the new task and write data to the checked surface.
Implement the wait functions, and add the necessary hubbub registers.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This enum definition is shared, so move it to a shared location.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make dml and integration with pplib clearer.
[How]
Change the way the dml formula is initialized to make its values more
clear. Restructure DC interface with pplib into rv_funcs.
Cap clocks received from pplib.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current periodic interrupt start point calc in optc
is not clear.
[How]
1. DM convert delta time to lines number and dc will calculate the
start position as per lines number and interrupt type.
2. hwss calculates the start point as per line offset.
3. optc programs vertical interrupts register as per start point
and interrupt source.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain tests fail after a fresh reboot. This is caused by writing to
registers prior to ungating the stream we're trying to program.
[How]
Make sure the stream is ungated before writing to its registers.
This also enables power-gating plane resources before init_hw
initializes them.
Additionally, this does some refactoring to move gating/ungating
from enable/disable_plane functions to where stream resources are
enabled/disabled.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When stream is blanked, pipe set command is sent to dmcu to notify it
that the abm pipe is disabled. When stream is unblanked, no notification is
made to dmcu that the abm pipe has been enabled, resulting in abm not
being enabled in the firmware.
[How]
When stream is unblanked, send a pipe set command to dmcu.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pipe related init is possible to optimized if we know what we
intend to program, and if we can determine it matches what is
already programmed for the pipe.
[How]
First step is to isolate the pipe related init code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
More clearly isolate the code that is involved in programming of
vupdate interrupt
[How]
Add function for programming of vupdate interrupt.
Call it after timing is programmed.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to figure out whether a timing we want to commit matches
something that GOP already programmed, in which case
we can decide to some optimizations
[How]
1. Add way to check for DIG FE
2. Add way to check for matching OTG timing
3. Add way to check for matching pixel clock (if possible)
- Currently only support DP for pixel clock, since it is easy to calc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VM_helper needs to be intialized with the dc struct in order to fix
an unallocated memory issue. System aperture settings should be
initialized to 0 and guarded with a check to make sure vm_config
is valid.
[How]
Allocate and free memory for vm_helper with other dc members.
Check whether the vm_config valid bit is set before initializing
aperture settings.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to calcualte vline position in DC for DCN.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enhanced sync need to use vertical_interrupt1.
[How]
Add vertical_interrupt1 source to irq manger,
Implment setup vline interrupt interface.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] After call bios table crtc_source_select, dal will program fmt
again. The bios table program dig_source_select and other fmt register
for bios usage which is redundancy and uncessary.
[How] Program dig_soruce_select register directly
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current date based versioning doesn't tell us about feature version
and build version, and is not useful for debug.
[How]
Add versioning based on feature and build
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
