Andrei reported a false alarm of lockdep at net/bridge/br_fdb.c:109,
this is because in Andrei's case, a spin_bug() was already triggered
before this, therefore the debug_locks is turned off, lockdep_is_held()
is no longer accurate after that. We should use lockdep_assert_held_once()
instead of lockdep_is_held() to respect debug_locks.
Fixes: 410b3d48f5 ("bridge: fdb: add proper lock checks in searching functions")
Reported-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive a BUSY packet for a call we think we've just completed, the
packet is handed off to the connection processor to deal with - but the
connection processor doesn't expect a BUSY packet and so flags a protocol
error.
Fix this by simply ignoring the BUSY packet for the moment.
The symptom of this may appear as a system call failing with EPROTO. This
may be triggered by pressing ctrl-C under some circumstances.
This comes about we abort calls due to interruption by a signal (which we
shouldn't do, but that's going to be a large fix and mostly in fs/afs/).
What happens is that we abort the call and may also abort follow up calls
too (this needs offloading somehoe). So we see a transmission of something
like the following sequence of packets:
DATA for call N
ABORT call N
DATA for call N+1
ABORT call N+1
in very quick succession on the same channel. However, the peer may have
deferred the processing of the ABORT from the call N to a background thread
and thus sees the DATA message from the call N+1 coming in before it has
cleared the channel. Thus it sends a BUSY packet[*].
[*] Note that some implementations (OpenAFS, for example) mark the BUSY
packet with one plus the callNumber of the call prior to call N.
Ordinarily, this would be call N, but there's no requirement for the
calls on a channel to be numbered strictly sequentially (the number is
required to increase).
This is wrong and means that the callNumber in the BUSY packet should
be ignored (it really ought to be N+1 since that's what it's in
response to).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anycast routes have the RTF_ANYCAST flag set, but when dumping routes
for userspace the route type is not set to RTN_ANYCAST. Make it so.
Fixes: 58c4fb86ea ("[IPV6]: Flag RTF_ANYCAST for anycast routes")
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alive tracking of nexthops can account for a link twice if the carrier
goes down followed by an admin down of the same link rendering multipath
routes useless. This is similar to 79099aab38 for UNREGISTER events and
DOWN events.
Fix by tracking number of alive nexthops in mpls_ifdown similar to the
logic in mpls_ifup. Checking the flags per nexthop once after all events
have been processed is simpler than trying to maintian a running count
through all event combinations.
Also, WRITE_ONCE is used instead of ACCESS_ONCE to set rt_nhn_alive
per a comment from checkpatch:
WARNING: Prefer WRITE_ONCE(<FOO>, <BAR>) over ACCESS_ONCE(<FOO>) = <BAR>
Fixes: c89359a42e ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Keep fragments equally sized, avoids some problems with too small fragments,
by Sven Eckelmann
- Initialize gateway class correctly when BATMAN V is compiled in,
by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=zGdm
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20170316' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Keep fragments equally sized, avoids some problems with too small fragments,
by Sven Eckelmann
- Initialize gateway class correctly when BATMAN V is compiled in,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a case for OVS_TUNNEL_KEY_ATTR_PAD to the switch statement
in ip_tun_from_nlattr in order to prevent the default case
returning an error.
Fixes: b46f6ded90 ("libnl: nla_put_be64(): align on a 64-bit area")
Signed-off-by: Kris Murphy <kriskend@linux.vnet.ibm.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.
To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.
Cc: stable@vger.kernel.org
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I mistakenly added the code to release sk->sk_frag in
sk_common_release() instead of sk_destruct()
TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call
sk_common_release() at close time, thus leaking one (order-3) page.
iSCSI is using such sockets.
Fixes: 5640f76858 ("net: use a per task frag allocator")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree, a
rather large batch of fixes targeted to nf_tables, conntrack and bridge
netfilter. More specifically, they are:
1) Don't track fragmented packets if the socket option IP_NODEFRAG is set.
From Florian Westphal.
2) SCTP protocol tracker assumes that ICMP error messages contain the
checksum field, what results in packet drops. From Ying Xue.
3) Fix inconsistent handling of AH traffic from nf_tables.
4) Fix new bitmap set representation with big endian. Fix mismatches in
nf_tables due to incorrect big endian handling too. Both patches
from Liping Zhang.
5) Bridge netfilter doesn't honor maximum fragment size field, cap to
largest fragment seen. From Florian Westphal.
6) Fake conntrack entry needs to be aligned to 8 bytes since the 3 LSB
bits are now used to store the ctinfo. From Steven Rostedt.
7) Fix element comments with the bitmap set type. Revert the flush
field in the nft_set_iter structure, not required anymore after
fixing up element comments.
8) Missing error on invalid conntrack direction from nft_ct, also from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with ipv6 source tunnel key address attribute
(OVS_TUNNEL_KEY_ATTR_IPV6_SRC) we are wrongly setting the tunnel
dst ip, fix that.
Fixes: 6b26ba3a7d ('openvswitch: netlink attributes for IPv6 tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should jump to invoke __nft_ct_set_destroy() instead of just
return error.
Fixes: edee4f1e92 ("netfilter: nft_ct: add zone id set support")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
When we notify peers of potential changes, it's also good to update
IGMP memberships. For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak, which happens if the connection request
is not fulfilled between parsing the DCCP options and handling the SYN
(because e.g. the backlog is full), because we forgot to free the
list of ack vectors.
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.
We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:
#8 [] page_fault at ffffffff8163e648
[exception RIP: __tcp_ack_snd_check+74]
.
.
#9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8
Of course it may happen with other NIC drivers as well.
It's found the freed dst_entry here:
224 static bool tcp_in_quickack_mode(struct sock *sk)↩
225 {↩
226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩
227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩
228 ↩
229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
231 }↩
But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.
All the vmcores showed 2 significant clues:
- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.
- All vmcores showed a postitive LockDroppedIcmps value, e.g:
LockDroppedIcmps 267
A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:
do_redirect()->__sk_dst_check()-> dst_release().
Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.
To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.
The dccp/IPv6 code is very similar in this respect, so fixing it there too.
As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().
Fixes: ceb3320610 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous idea was to check whether a net namespace is in
net_exit_list or not. It doesn't work, because net->exit_list is used in
__register_pernet_operations and __unregister_pernet_operations where
all namespaces are added to a temporary list to make cleanup in a error
case, so list_empty(&net->exit_list) always returns false.
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Fixes: 002d8a1a6c ("net: skip genenerating uevents for network namespaces that are exiting")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.
Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.
A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.
However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.
Fixes: 34666d467c ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned. If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.
However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.
In case original skb is cloned this munges nexthdr value of another
skb. Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.
This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active: tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2759647247 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.
Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.
Reproducer:
===========
#!/bin/sh
ip netns add ns1
ip netns add ns2
ip -net ns1 link set lo up
for x in 0 1 2 ; do
ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
ip -net ns1 link set eth$x up
ip -net ns2 link set veth$x up
done
ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048
echo "before replace, 3 routes"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
echo
ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2
echo "after replace, only 2 routes, metric 2048 is gone"
ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1f48ff6c53.
This patch is not required anymore now that we keep a dummy list of
set elements in the bitmap set implementation, so revert this before
we forget this code has no clients.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Element comments may come without any prior set flag, so we have to keep
a list of dummy struct nft_set_ext to keep this information around. This
is only useful for set dumps to userspace. From the packet path, this
set type relies on the bitmap representation. This patch simplifies the
logic since we don't need to allocate the dummy nft_set_ext structure
anymore on the fly at the cost of increasing memory consumption because
of the list of dummy struct nft_set_ext.
Fixes: 665153ff57 ("netfilter: nf_tables: add bitmap set type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since the nfct and nfctinfo have been combined, the nf_conn structure
must be at least 8 bytes aligned, as the 3 LSB bits are used for the
nfctinfo. But there's a fake nf_conn structure to denote untracked
connections, which is created by a PER_CPU construct. This does not
guarantee that it will be 8 bytes aligned and can break the logic in
determining the correct nfctinfo.
I triggered this on a 32bit machine with the following error:
BUG: unable to handle kernel NULL pointer dereference at 00000af4
IP: nf_ct_deliver_cached_events+0x1b/0xfb
*pdpt = 0000000031962001 *pde = 0000000000000000
Oops: 0000 [#1] SMP
[Modules linked in: ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipv6 crc_ccitt ppdev r8169 parport_pc parport
OK ]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-test+ #75
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
task: c126ec00 task.stack: c1258000
EIP: nf_ct_deliver_cached_events+0x1b/0xfb
EFLAGS: 00010202 CPU: 0
EAX: 0021cd01 EBX: 00000000 ECX: 27b0c767 EDX: 32bcb17a
ESI: f34135c0 EDI: f34135c0 EBP: f2debd60 ESP: f2debd3c
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000af4 CR3: 309a0440 CR4: 001406f0
Call Trace:
<SOFTIRQ>
? ipv6_skip_exthdr+0xac/0xcb
ipv6_confirm+0x10c/0x119 [nf_conntrack_ipv6]
nf_hook_slow+0x22/0xc7
nf_hook+0x9a/0xad [ipv6]
? ip6t_do_table+0x356/0x379 [ip6_tables]
? ip6_fragment+0x9e9/0x9e9 [ipv6]
ip6_output+0xee/0x107 [ipv6]
? ip6_fragment+0x9e9/0x9e9 [ipv6]
dst_output+0x36/0x4d [ipv6]
NF_HOOK.constprop.37+0xb2/0xba [ipv6]
? icmp6_dst_alloc+0x2c/0xfd [ipv6]
? local_bh_enable+0x14/0x14 [ipv6]
mld_sendpack+0x1c5/0x281 [ipv6]
? mark_held_locks+0x40/0x5c
mld_ifc_timer_expire+0x1f6/0x21e [ipv6]
call_timer_fn+0x135/0x283
? detach_if_pending+0x55/0x55
? mld_dad_timer_expire+0x3e/0x3e [ipv6]
__run_timers+0x111/0x14b
? mld_dad_timer_expire+0x3e/0x3e [ipv6]
run_timer_softirq+0x1c/0x36
__do_softirq+0x185/0x37c
? test_ti_thread_flag.constprop.19+0xd/0xd
do_softirq_own_stack+0x22/0x28
</SOFTIRQ>
irq_exit+0x5a/0xa4
smp_apic_timer_interrupt+0x2a/0x34
apic_timer_interrupt+0x37/0x3c
By using DEFINE/DECLARE_PER_CPU_ALIGNED we can enforce at least 8 byte
alignment as all cache line sizes are at least 8 bytes or more.
Fixes: a9e419dc7b ("netfilter: merge ctinfo into nfct pointer storage area")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
consider a bridge with mtu 9000, but end host sending smaller
packets to another host with mtu < 9000.
In this case, after reassembly, bridge+defrag would refragment,
and then attempt to send the reassembled packet as long as it
was below 9k.
Instead we have to cap by the largest fragment size seen.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, there are two different methods to store an u16 integer to
the u32 data register. For example:
u32 *dest = ®s->data[priv->dreg];
1. *dest = 0; *(u16 *) dest = val_u16;
2. *dest = val_u16;
For method 1, the u16 value will be stored like this, either in
big-endian or little-endian system:
0 15 31
+-+-+-+-+-+-+-+-+-+-+-+-+
| Value | 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+
For method 2, in little-endian system, the u16 value will be the same
as listed above. But in big-endian system, the u16 value will be stored
like this:
0 15 31
+-+-+-+-+-+-+-+-+-+-+-+-+
| 0 | Value |
+-+-+-+-+-+-+-+-+-+-+-+-+
So later we use "memcmp(®s->data[priv->sreg], data, 2);" to do
compare in nft_cmp, nft_lookup expr ..., method 2 will get the wrong
result in big-endian system, as 0~15 bits will always be zero.
For the similar reason, when loading an u16 value from the u32 data
register, we should use "*(u16 *) sreg;" instead of "(u16)*sreg;",
the 2nd method will get the wrong value in the big-endian system.
So introduce some wrapper functions to store/load an u8 or u16
integer to/from the u32 data register, and use them in the right
place.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently we just assume the element key as a u32 integer, regardless of
the set key length.
This is incorrect, for example, the tcp port number is only 16 bits.
So when we use the nft_payload expr to get the tcp dport and store
it to dreg, the dport will be stored at 0~15 bits, and 16~31 bits
will be padded with zero.
So the reg->data[dreg] will be looked like as below:
0 15 31
+-+-+-+-+-+-+-+-+-+-+-+-+
| tcp dport | 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+
But for these big-endian systems, if we treate this register as a u32
integer, the element key will be larger than 65535, so the following
lookup in bitmap set will cause out of bound access.
Another issue is that if we add element with comments in bitmap
set(although the comments will be ignored eventually), the element will
vanish strangely. Because we treate the element key as a u32 integer, so
the comments will become the part of the element key, then the element
key will also be larger than 65535 and out of bound access will happen:
# nft add element t s { 1 comment test }
Since set->klen is 1 or 2, it's fine to treate the element key as a u8 or
u16 integer.
Fixes: 665153ff57 ("netfilter: nf_tables: add bitmap set type")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Multipath routes can be rendered usesless when a device in one of the
paths is deleted. For example:
$ ip -f mpls ro ls
100
nexthop as to 200 via inet 172.16.2.2 dev virt12
nexthop as to 300 via inet 172.16.3.2 dev br0
101
nexthop as to 201 via inet6 2000:2::2 dev virt12
nexthop as to 301 via inet6 2000:3::2 dev br0
$ ip li del br0
When br0 is deleted the other hop is not considered in
mpls_select_multipath because of the alive check -- rt_nhn_alive
is 0.
rt_nhn_alive is decremented once in mpls_ifdown when the device is taken
down (NETDEV_DOWN) and again when it is deleted (NETDEV_UNREGISTER). For
a 2 hop route, deleting one device drops the alive count to 0. Since
devices are taken down before unregistering, the decrement on
NETDEV_UNREGISTER is redundant.
Fixes: c89359a42e ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mpls_router module is unloaded, mpls routes are deleted but
notifications are not sent to userspace leaving userspace caches
out of sync. Add the call to mpls_notify_route in mpls_net_exit as
routes are freed.
Fixes: 0189197f44 ("mpls: Basic routing support")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RxRPC ACK packet may contain an extension that includes the peer's
current Rx window size for this call. We adjust the local Tx window size
to match. However, the transmitter can stall if the receive window is
reduced to 0 by the peer and then reopened.
This is because the normal way that the transmitter is re-energised is by
dropping something out of our Tx queue and thus making space. When a
single gap is made, the transmitter is woken up. However, because there's
nothing in the Tx queue at this point, this doesn't happen.
To fix this, perform a wake_up() any time we see the peer's Rx window size
increasing.
The observable symptom is that calls start failing on ETIMEDOUT and the
following:
kAFS: SERVER DEAD state=-62
appears in dmesg.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rxrpc_kernel_send_data() is asked to send data through a call that has
already failed (due to a remote abort, received protocol error or network
error), then return the associated error code saved in the call rather than
ESHUTDOWN.
This allows the caller to work out whether to ask for the abort code or not
based on this.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c146066ab8 ("ipv4: Don't use ufo handling on later transformed
packets") and commit f89c56ce71 ("ipv6: Don't use ufo handling on
later transformed packets") added a check that 'rt->dst.header_len' isn't
zero in order to skip UFO, but it doesn't include IPcomp in transport mode
where it equals zero.
Packets, after payload compression, may not require further fragmentation,
and if original length exceeds MTU, later compressed packets will be
transmitted incorrectly. This can be reproduced with LTP udp_ipsec.sh test
on veth device with enabled UFO, MTU is 1500 and UDP payload is 2000:
* IPv4 case, offset is wrong + unnecessary fragmentation
udp_ipsec.sh -p comp -m transport -s 2000 &
tcpdump -ni ltp_ns_veth2
...
IP (tos 0x0, ttl 64, id 45203, offset 0, flags [+],
proto Compressed IP (108), length 49)
10.0.0.2 > 10.0.0.1: IPComp(cpi=0x1000)
IP (tos 0x0, ttl 64, id 45203, offset 1480, flags [none],
proto UDP (17), length 21) 10.0.0.2 > 10.0.0.1: ip-proto-17
* IPv6 case, sending small fragments
udp_ipsec.sh -6 -p comp -m transport -s 2000 &
tcpdump -ni ltp_ns_veth2
...
IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
payload length: 37) fd00::2 > fd00::1: IPComp(cpi=0x1000)
IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108)
payload length: 21) fd00::2 > fd00::1: IPComp(cpi=0x1000)
Fix it by checking 'rt->dst.xfrm' pointer to 'xfrm_state' struct, skip UFO
if xfrm is set. So the new check will include both cases: IPcomp and IPsec.
Fixes: c146066ab8 ("ipv4: Don't use ufo handling on later transformed packets")
Fixes: f89c56ce71 ("ipv6: Don't use ufo handling on later transformed packets")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN reports a use of uninitialized memory in put_cmsg() because
msg.msg_flags in recvfrom haven't been initialized properly.
The flag values don't affect the result on this path, but it's still a
good idea to initialize them explicitly.
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gso code of several tunnels type (gre and udp tunnels)
takes for granted that the skb->inner_protocol is properly
initialized and drops the packet elsewhere.
On the forwarding path no one is initializing such field,
so gro encapsulated packets are dropped on forward.
Since commit 3872035241 ("gre: Use inner_proto to obtain
inner header protocol"), this can be reproduced when the
encapsulated packets use gre as the tunneling protocol.
The issue happens also with vxlan and geneve tunnels since
commit 8bce6d7d0d ("udp: Generalize skb_udp_segment"), if the
forwarding host's ingress nic has h/w offload for such tunnel
and a vxlan/geneve device is configured on top of it, regardless
of the configured peer address and vni.
To address the issue, this change initialize the inner_protocol
field for encapsulated packets in both ipv4 and ipv6 gro complete
callbacks.
Fixes: 3872035241 ("gre: Use inner_proto to obtain inner header protocol")
Fixes: 8bce6d7d0d ("udp: Generalize skb_udp_segment")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function rds_ib_setup_qp, the error handle is missing. When some
error occurs, it is possible that memory leak occurs. As such, error
handle is added.
Cc: Joe Jin <joe.jin@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Guanglei Li <guanglei.li@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dinesh reported that RTA_MULTIPATH nexthops are 8-bytes larger with IPv6
than IPv4. The recent refactoring for multipath support in netlink
messages does discriminate between non-multipath which needs the OIF
and multipath which adds a rtnexthop struct for each hop making the
RTA_OIF attribute redundant. Resolve by adding a flag to the info
function to skip the oif for multipath.
Fixes: beb1afac51 ("net: ipv6: Add support to dump multipath routes
via RTA_MULTIPATH attribute")
Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding RFC 792, the first 64 bits of the original SCTP datagram's
data could be contained in ICMP packet, such as:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| unused |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Internet Header + 64 bits of Original Data Datagram |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
However, according to RFC 4960, SCTP datagram header is as below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port Number | Destination Port Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Verification Tag |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
It means only the first three fields of SCTP header can be carried in
ICMP packet except for Checksum field.
At present in sctp_manip_pkt(), no matter whether the packet is ICMP or
not, it always calculates SCTP packet checksum. However, not only the
calculation of checksum is unnecessary for ICMP, but also it causes
another fatal issue that ICMP packet is dropped. The header size of
SCTP is used to identify whether the writeable length of skb is bigger
than skb->len through skb_make_writable() in sctp_manip_pkt(). But
when it deals with ICMP packet, skb_make_writable() directly returns
false as the writeable length of skb is bigger than skb->len.
Subsequently ICMP is dropped.
Now we correct this misbahavior. When sctp_manip_pkt() handles ICMP
packet, 8 bytes rather than the whole SCTP header size is used to check
if writeable length of skb is overflowed. Meanwhile, as it's meaningless
to calculate checksum when packet is ICMP, the computation of checksum
is ignored as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Andrey reports syzkaller splat caused by
NF_CT_ASSERT(!ip_is_fragment(ip_hdr(skb)));
in ipv4 nat. But this assertion (and the comment) are wrong, this function
does see fragments when IP_NODEFRAG setsockopt is used.
As conntrack doesn't track packets without complete l4 header, only the
first fragment is tracked.
Because applying nat to first packet but not the rest makes no sense this
also turns off tracking of all fragments.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-03-06
1) Fix lockdep splat on xfrm policy subsystem initialization.
From Florian Westphal.
2) When using socket policies on IPv4-mapped IPv6 addresses,
we access the flow informations of the wrong address family
what leads to an out of bounds access. Fix this by using
the family we get with the dst_entry, like we do it for the
standard policy lookup.
3) vti6 can report a PMTU below IPV6_MIN_MTU. Fix this by
adding a check for that before sending a ICMPV6_PKT_TOOBIG
message.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a93d01f577 ("RDS: TCP: avoid bad page reference in
rds_tcp_listen_data_ready") added the function
rds_tcp_listen_sock_def_readable() to handle the case when a
partially set-up acceptor socket drops into rds_tcp_listen_data_ready().
However, if the listen socket (rtn->rds_tcp_listen_sock) is itself going
through a tear-down via rds_tcp_listen_stop(), the (*ready)() will be
null and we would hit a panic of the form
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: (null)
:
? rds_tcp_listen_data_ready+0x59/0xb0 [rds_tcp]
tcp_data_queue+0x39d/0x5b0
tcp_rcv_established+0x2e5/0x660
tcp_v4_do_rcv+0x122/0x220
tcp_v4_rcv+0x8b7/0x980
:
In the above case, it is not fatal to encounter a NULL value for
ready- we should just drop the packet and let the flush of the
acceptor thread finish gracefully.
In general, the tear-down sequence for listen() and accept() socket
that is ensured by this commit is:
rtn->rds_tcp_listen_sock = NULL; /* prevent any new accepts */
In rds_tcp_listen_stop():
serialize with, and prevent, further callbacks using lock_sock()
flush rds_wq
flush acceptor workq
sock_release(listen socket)
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Order of initialization in rds_tcp_init needs to be done so
that resources are set up and destroyed in the correct synchronization
sequence with both the data path, as well as netns create/destroy
path. Specifically,
- we must call register_pernet_subsys and get the rds_tcp_netid
before calling register_netdevice_notifier, otherwise we risk
the sequence
1. register_netdevice_notifier sets up netdev notifier callback
2. rds_tcp_dev_event -> rds_tcp_kill_sock uses netid 0, and finds
the wrong rtn, resulting in a panic with string that is of the form:
BUG: unable to handle kernel NULL pointer dereference at 000000000000000d
IP: rds_tcp_kill_sock+0x3a/0x1d0 [rds_tcp]
:
- the rds_tcp_incoming_slab kmem_cache must be initialized before the
datapath starts up. The latter can happen any time after the
pernet_subsys registration of rds_tcp_net_ops, whose -> init
function sets up the listen socket. If the rds_tcp_incoming_slab has
not been set up at that time, a panic of the form below may be
encountered
BUG: unable to handle kernel NULL pointer dereference at 0000000000000014
IP: kmem_cache_alloc+0x90/0x1c0
:
rds_tcp_data_recv+0x1e7/0x370 [rds_tcp]
tcp_read_sock+0x96/0x1c0
rds_tcp_recv_path+0x65/0x80 [rds_tcp]
:
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is incorrect for the rds_connection to piggyback on the
sock_net() refcount for the netns because this gives rise to
a chicken-and-egg problem during rds_conn_destroy. Instead explicitly
take a ref on the net, and hold the netns down till the connection
tear-down is complete.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX skbs do not necessarily hold a reference on skb->sk->sk_refcnt
By the time TX completion happens, sk_refcnt might be already 0.
sock_hold()/sock_put() would then corrupt critical state, like
sk_wmem_alloc and lead to leaks or use after free.
Fixes: 62bccb8cdb ("net-timestamp: Make the clone operation stand-alone from phy timestamping")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX skbs do not necessarily hold a reference on skb->sk->sk_refcnt
By the time TX completion happens, sk_refcnt might be already 0.
sock_hold()/sock_put() would then corrupt critical state, like
sk_wmem_alloc.
Fixes: bf7fa551e0 ("mac80211: Resolve sk_refcnt/sk_wmem_alloc issue in wifi ack path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call state may be changed at any time by the data-ready routine in
response to received packets, so if the call state is to be read and acted
upon several times in a function, READ_ONCE() must be used unless the call
state lock is held.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov reported a divide by 0 triggered by syzkaller, exploiting
tcp_disconnect() path that was never really considered and/or used
before syzkaller ;)
I was not able to reproduce the bug, but it seems issues here are the
three possible actions that assumed they would never trigger on a
listener.
1) tcp_write_timer_handler
2) tcp_delack_timer_handler
3) MTU reduction
Only IPv6 MTU reduction was properly testing TCP_CLOSE and TCP_LISTEN
states from tcp_v6_mtu_reduced()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
osd_request_timeout specifies how many seconds to wait for a response
from OSDs before returning -ETIMEDOUT from an OSD request. 0 (default)
means no limit.
osd_request_timeout is osdkeepalive-precise -- in-flight requests are
swept through every osdkeepalive seconds. With ack vs commit behaviour
gone, abort_request() is really simple.
This is based on a patch from Artur Molchanov <artur.molchanov@synesis.ru>.
Tested-by: Artur Molchanov <artur.molchanov@synesis.ru>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
