The switchtec_ntb driver has a couple requirements on the switchec's
hardware configuration so we add these notes to the documentation.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Switchtec hardware has two types of memory windows: LUTs and Direct.
The first area in each BAR is for LUT windows and the remaining area is
for the direct region. The total number of LUT entries is set by a
configuration setting in hardware and they all must be the same
size. (This is fixed by switchtec_ntb to be 64K.)
switchtec_ntb enables the LUTs only for the first BAR and enables the
highest power of two possible. Seeing the LUTs are at the beginning of
the BAR, the direct memory window's alignment is affected. Therefore,
the maximum direct memory window size can not be greater than the number
of LUTs times 64K. The direct window in other BARs will not have this
restriction as the LUTs will not be enabled there. LUTs will only be
exposed through the NTB API if the use_lut_mw parameter is set.
Seeing the Switchtec hardware, by default, configures BARs to be 4G a
module parameter is given to limit the size of the advertised memory
windows. Higher layers tend to allocate the maximum BAR size and this
has a tendency to fail when they try to allocate 4GB of contiguous
memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Seeing there is no dedicated hardware for this, we simply add
these as entries in the shared memory window. Thus, we could support
any number of them but 128 seems like enough, for now.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pretty straightforward implementation of doorbell registers.
The shift and mask were setup in an earlier patch and this just hooks
up the appropriate portion of the IDB register as the local doorbells
and the opposite portion of ODB as the peer doorbells. The DB mask is
protected by a spinlock to avoid concurrent read-modify-write accesses.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
switchtec_ntb checks for a link by looking at the shared memory
window. If the magic number is correct and the other side indicates
their link is enabled then we take the link to be up.
Whenever we change our local link status we send a msg to the
other side to check whether it's up and change their status.
The current status is maintained in a flag so ntb_is_link_up
can return quickly.
We utilize Switchtec's link status notifier to also check link changes
when the switch notices a port changes state.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add a skeleton NTB driver which will be filled out in subsequent patches.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set up some hardware registers and creates interrupt service routines
for the doorbells and messages.
There are 64 doorbells in the switch that are shared between all
partitions. The upper 4 doorbells are also shared with the messages
and are therefore not used. Thus, this provides 28 doorbells for each
partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add the code to initialize the memory windows in the hardware.
This includes setting up the requester ID table, and figuring out
which BAR corresponds to which memory window. (Seeing the switch
can be configured with any number of BARs.)
Also, seeing the device doesn't have hardware for scratchpads or
determining the link status, we create a shared memory window that has
these features. A magic number with a version component will be used
to determine if the other side's driver is actually up.
The shared memory window also informs the other side of the
size and count of the local memory windows.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Adds a comment and a check to ntb_mw_get_align() so that it always fails
if the function is called before the link is up.
Also adds a comment to ntb_mw_count() to note that it may return 0 if
it is called before the link is up.
This is to prevent accidental mis-use in clients that are testing
on hardware that this doesn't matter for.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
With Switchtec hardware it's impossible to get the alignment parameters
for a peer's memory window until the peer's driver has configured its
windows. Strictly speaking, the link doesn't have to be up for this,
but the link being up is the only way the client can tell that
the other side has been configured.
This patch converts ntb_transport and ntb_perf to use this function after
the link goes up. This simplifies these clients slightly because they
no longer have to store the alignment parameters. It also tweaks
ntb_tool so that peer_mw_trans will print zero if it is run before
the link goes up.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In order for the Switchtec NTB code to handle link change events we
create a notifier callback in the switchtec code which gets called
whenever an appropriate event interrupt occurs.
In order to preserve userspace's ability to follow these events,
we compare the event count with a stored copy from last time we
checked.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There are two additional regions: ctrl and dbmsg. The first is
for generic NTB control and memory windows. The second is for doorbells
and message registers. This patch also adds a number of related
constants for using these registers.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
We export the class pointer symbol and add an extern define in the
Switchtec header file.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Create the switchtec.h header in include/linux with hardware defines
and the switchtec_dev structure. Both moved directly from switchtec.c.
This is a prep patch for creating an NTB driver for Switchtec.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull x86 fixes from Thomas Gleixner:
"A set of small fixes:
- make KGDB work again which got broken by the conversion of WARN()
to #UD. The WARN fixup needs to run before the notifier callchain,
otherwise KGDB tries to handle it and crashes.
- disable KASAN in the ORC unwinder to prevent false positive KASAN
warnings
- prevent default mapping above 47bit when 5 level page tables are
enabled
- make the delay calibration optimization work correctly, which had
the conditionals the wrong way around and was operating on data
which was not yet updated.
- remove the bogus X86_TRAP_BP trap init from the default IDT init
table, which broke 32bit int3 handling by overwriting the correct
int3 setup.
- replace this_cpu* with boot_cpu_data access in the preemptible
oprofile init code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Handle warnings before the notifier chain, to fix KGDB crash
x86/mm: Fix ELF_ET_DYN_BASE for 5-level paging
x86/idt: Remove X86_TRAP_BP initialization in idt_setup_traps()
x86/oprofile/ppro: Do not use __this_cpu*() in preemptible context
x86/unwind: Disable KASAN checking in the ORC unwinder
x86/smpboot: Make optimization of delay calibration work correctly
Pull perf tool fixes from Thomas Gleixner:
"A small set of fixes for perf tool:
- synchronize the i915 drm header to avoid the 'out of date' warning
- make sure that perf trace cleans up its temporary files on exit
- unbreak the build with newer flex versions
- add missing braces in the eBPF parsing rules"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tooling/headers: Sync the tools/include/uapi/drm/i915_drm.h UAPI header
perf trace: Call machine__exit() at exit
perf tools: Fix eBPF event specification parsing
perf tools: Add "reject" option for parse-events.l
Pull networking fixes from David Miller:
1) Use after free in vlan, from Cong Wang.
2) Handle NAPI poll with a zero budget properly in mlx5 driver, from
Saeed Mahameed.
3) If DMA mapping fails in mlx5 driver, NULL out page, from Inbar
Karmy.
4) Handle overrun in RX FIFO of sun4i CAN driver, from Gerhard
Bertelsmann.
5) Missing return in mdb and vlan prepare phase of DSA layer, from
Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
vlan: fix a use-after-free in vlan_device_event()
net: dsa: return after vlan prepare phase
net: dsa: return after mdb prepare phase
can: ifi: Fix transmitter delay calculation
tcp: fix tcp_fastretrans_alert warning
tcp: gso: avoid refcount_t warning from tcp_gso_segment()
can: peak: Add support for new PCIe/M2 CAN FD interfaces
can: sun4i: handle overrun in RX FIFO
can: c_can: don't indicate triple sampling support for D_CAN
net/mlx5e: Increase Striding RQ minimum size limit to 4 multi-packet WQEs
net/mlx5e: Set page to null in case dma mapping fails
net/mlx5e: Fix napi poll with zero budget
net/mlx5: Cancel health poll before sending panic teardown command
net/mlx5: Loop over temp list to release delay events
rds: ib: Fix NULL pointer dereference in debug code
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAloFoQQTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9hzQB/402UdBXnM4/AId9zYcvY/4XnE4bSvP
pi+46vQnSAtz2Mo0i/mjnEFVu1/+SNfdKFhSuKrBI/G4Q5pWLRd/7SBFReMnqKvr
lbsZnqZuyYKQW1Qzccm4t3BXIEa/tNhvz93QMQLv6vX3vADEwCUm5S9acaYFKqi7
b1QfQtn6olbBwCanQ4ICUECUXMeq78P7D763T5F9m0KyQJ9XIfyeM+JA6uzwaUoO
IUFG2XPJlmdcVu34u3zV9YZ3UqaconhUwyO41prhZUqwWy6KmZQL71JEXYvn+OYY
mkdfoK/1pFskkOBc3eMRUhtL3c7veCUhzblQBzImrlNUiDrHpJUxLUZQ
=XO2t
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.14-20171110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-11-10
this is a pull request for net/master.
The first patch by Richard Schütz for the c_can driver removes the false
indication to support triple sampling for d_can. Gerhard Bertelsmann's
patch for the sun4i driver improves the RX overrun handling. The patch
by Stephane Grosjean for the peak_canfd driver adds the PCI ids for
various new PCIe/M2 interfaces. Marek Vasut's patch for the ifi driver
fix transmitter delay calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-11-08
The following series includes some fixes for mlx5 core and etherent
driver.
Sorry for the late submission but as you can see i have some very
critical fixes below that i would like them merged into this RC.
Please pull and let me know if there is any problem.
For -stable:
('net/mlx5e: Set page to null in case dma mapping fails') kernels >= 4.13
('net/mlx5: FPGA, return -EINVAL if size is zero') kernels >= 4.13
('net/mlx5: Cancel health poll before sending panic teardown command') kernels >= 4.13
V1->V2:
- Fix Reviewed-by tag of the 2nd patch.
- Drop the FPGA 0 size fix, it needs some more change log info.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After refcnt reaches zero, vlan_vid_del() could free
dev->vlan_info via RCU:
RCU_INIT_POINTER(dev->vlan_info, NULL);
call_rcu(&vlan_info->rcu, vlan_info_rcu_free);
However, the pointer 'grp' still points to that memory
since it is set before vlan_vid_del():
vlan_info = rtnl_dereference(dev->vlan_info);
if (!vlan_info)
goto out;
grp = &vlan_info->grp;
Depends on when that RCU callback is scheduled, we could
trigger a use-after-free in vlan_group_for_each_dev()
right following this vlan_vid_del().
Fix it by moving vlan_vid_del() before setting grp. This
is also symmetric to the vlan_vid_add() we call in
vlan_device_event().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: efc73f4bbc ("net: Fix memory leak - vlan_info struct")
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last minute upstream update to one of the UAPI headers - sync it with tooling,
to address this warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.
Fixes: 1ca4aa9cd4 ("net: dsa: check VLAN capability of every switch")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.
Fixes: a1a6b7ea7f ("net: dsa: add cross-chip multicast support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJaBbFwAAoJEEp/3jgCEfOLYKAH/iB9iIJigf/Khv4S/iKp8hw0
q8kXPfSis2LCYWQjXnPtz1/f9vidiRRb5tw76sInn/hHgzbvGb4nWcGQV3zz0BqF
MOZmJxPzsDH3NUNZ5m5qHFAQpP+hm3I+6JeuQh1DshZOitI0BtGmQ5cnRW7pL+Ny
PZHCXonTtuUcURI6YTW43zh0XqlBdmZe9MUlSLQkKhsW+VRQXenz51a7KO64muoG
KxiVXewpgWHARQ27ck1xTBAQdTUZ14w0hjTH7FsqdMT5O7kCUzEgWl/zcQUs+Kxg
0j8fIsxrxYVT5Wya02y+1OkpoLfavR7resxnPwdZ1e9/QubfbK8OjtrSF87uwh0=
=wJA0
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.14-rc9' of git://github.com/ceph/ceph-client
Pull ceph gix from Ilya Dryomov:
"Memory allocation flags fix, marked for stable"
* tag 'ceph-for-4.14-rc9' of git://github.com/ceph/ceph-client:
rbd: use GFP_NOIO for parent stat and data requests
Pull input layer updates from Dmitry Torokhov:
- a new ACPI ID for Elan touchpad found in yet another Ideapad model
- Synaptics RMI4 will allow binding to controllers reporting SMB
version 3 (note that we are not adding any new ACPI IDs to the
Synaptics PS/2 drover so unless user explicitly enables intertouch
support there is no user-visible change)
- a fixup to TSC 2004/5 touchscreen driver to mark input devices as
"direct" to help userspace identify the type of device they are
dealing with
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
Input: tsc200x-core - set INPUT_PROP_DIRECT
Input: elan_i2c - add ELAN060C to the ACPI table
Fix PPC HV host crash that can occur as a result of resizing the guest
hashed page table.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaBc/CAAoJEED/6hsPKofoI5QH/jxfWMsIcDy0iLPFPywKEV0K
bPt2e47qdWAYNByIgw2QSJBJtcay+LsXbheBlxSxsGO61ceK3HkUfr9CfXvRCpjQ
rdZwHArmpZSFTPYOcXfElF2BkJ+1kOZsDphfzrNVwUF3Q0Y+588IGQm1uv2bUKnA
QAzXFXDDzyKhLqknWoacUlM5UyYKmQwBVSfCFTsQBxhk34agIXH92ZYZLLGWJU6H
B+sjNu5plCoeorWK1NqMtOPAXHs7oV7gHxZLtDM6RL7jZVmYAbDA4zCqk/i2Vy4z
ZU1ihPD8QwvGMuJIsPwcC0ojUVwGP7ZMz/F3FhWSR/VzpRe6SU7T7LxMc1ZsGN0=
=8FAZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fix from Radim Krčmář:
"Fix PPC HV host crash that can occur as a result of resizing the guest
hashed page table"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Fix exclusion between HPT resizing and other HPT updates
A final few MIPS fixes for 4.14:
- Fix BMIPS NULL pointer dereference (4.7)
- Fix AR7 early GPIO init allocation failure (3.19)
- Fix dead serial output on certain AR7 platforms (2.6.35)
-----BEGIN PGP SIGNATURE-----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=tNHp
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_4.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A final few MIPS fixes for 4.14:
- fix BMIPS NULL pointer dereference (4.7)
- fix AR7 early GPIO init allocation failure (3.19)
- fix dead serial output on certain AR7 platforms (2.6.35)"
* tag 'mips_fixes_4.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: AR7: Ensure that serial ports are properly set up
MIPS: AR7: Defer registration of GPIO
MIPS: BMIPS: Fix missing cbr address
Following my recent transition from Imagination Technologies to the=20
reincarnated MIPS company add a .mailmap mapping for my work address,
so that `scripts/get_maintainer.pl' gets it right for past commits.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 941f5f0f6e.
Sadly, it turns out that we really can't just do the cross-CPU IPI to
all CPU's to get their proper frequencies, because it's much too
expensive on systems with lots of cores.
So we'll have to revert this for now, and revisit it using a smarter
model (probably doing one system-wide IPI at open time, and doing all
the frequency calculations in parallel).
Reported-by: WANG Chao <chao.wang@ucloud.cn>
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Rafael J Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaBRSBAAoJEAx081l5xIa+XDoQAIrNH5h8o72oDls3if5t1ZLx
8aQW7LBFXUvlG8W6hmeT63xSVkDHfLHK5/6QZ96EdSAiUY/pt7mduW54V6xAzYr8
RBtOgAiLY1KQ9p3m0CoO5c9Mids3KcoUpVZlfhdnAETekDCNoWItbRxd3h/sufmN
SJi7LN3Ra1O83IFgeidREdvQlB+1zwaMrH/sxbDDmssSpUBtQon+F2P4/jZxawhO
JZaw0EFWvwNMCbA2415jQrwgkvd9OZfzeaYhzJ5VZtprO6xi9xXmIFknAzrsluwO
WaecwktXOfvZHVYEYpjZmeoP/BcHINGsb7luPW5ee6EznnN5lXgdKNfNtrLwwuoL
MYC+dJcM5203IWEm96iQwfvWCojLsBM7KbH+/1oUWcI/ipoOngebgpdlUUc5q8bd
GkPXXJZVxYL14NiJr6iWx045Hk+KgmeDbEtsHZjiDM6t2PG0V1Q3+iI+oU4AUgc7
Px3IOTqIOZJsS2WGDIAAmWyON3RKnZPc7ewargAJyQaR/GthoPKt/TIhMSz74Lxj
gn8SV0yih+ZDxrUGApkpJZfTNaIYCKbAz/yyP0GWNQIE4XpPPTggpwQgEUn/yzP+
owNn34Iw9QPLBp1sIXglCebaYHmG54PcWjr86I1wY9nIYB/UFwF7AMjRl47Z/4+M
AaDrzESPuVs3MIWSYt4e
=MO5T
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.14-rc9' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Last few patches to wrap up.
Two i915 fixes that are on their way to stable, one vmware black
screen bug, and one const patch that I was going to drop, but it was
clearly a pretty safe one liner"
* tag 'drm-fixes-for-v4.14-rc9' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Deconstruct struct sgt_dma initialiser
drm/i915: Reject unknown syncobj flags
drm/vmwgfx: Fix Ubuntu 17.10 Wayland black screen issue
drm/vmwgfx: constify vmw_fence_ops
The CANFD transmitter delay calculation formula was updated in the
latest software drop from IFI and improves the behavior of the IFI
CANFD core during bitrate switching. Use the new formula to improve
stability of the CANFD operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the cause of an WARNING indicatng TCP has pending
retransmission in Open state in tcp_fastretrans_alert().
The root cause is a bad interaction between path mtu probing,
if enabled, and the RACK loss detection. Upong receiving a SACK
above the sequence of the MTU probing packet, RACK could mark the
probe packet lost in tcp_fastretrans_alert(), prior to calling
tcp_simple_retransmit().
tcp_simple_retransmit() only enters Loss state if it newly marks
the probe packet lost. If the probe packet is already identified as
lost by RACK, the sender remains in Open state with some packets
marked lost and retransmitted. Then the next SACK would trigger
the warning. The likely scenario is that the probe packet was
lost due to its size or network congestion. The actual impact of
this warning is small by potentially entering fast recovery an
ACK later.
The simple fix is always entering recovery (Loss) state if some
packet is marked lost during path MTU probing.
Fixes: a0370b3f3f ("tcp: enable RACK loss detection to trigger recovery")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a GSO skb of truesize O is segmented into 2 new skbs of truesize N1
and N2, we want to transfer socket ownership to the new fresh skbs.
In order to avoid expensive atomic operations on a cache line subject to
cache bouncing, we replace the sequence :
refcount_add(N1, &sk->sk_wmem_alloc);
refcount_add(N2, &sk->sk_wmem_alloc); // repeated by number of segments
refcount_sub(O, &sk->sk_wmem_alloc);
by a single
refcount_add(sum_of(N) - O, &sk->sk_wmem_alloc);
Problem is :
In some pathological cases, sum(N) - O might be a negative number, and
syzkaller bot was apparently able to trigger this trace [1]
atomic_t was ok with this construct, but we need to take care of the
negative delta with refcount_t
[1]
refcount_t: saturated; leaking memory.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 8404 at lib/refcount.c:77 refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 8404 Comm: syz-executor2 Not tainted 4.14.0-rc5-mm1+ #20
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x41c kernel/panic.c:183
__warn+0x1c4/0x1e0 kernel/panic.c:546
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:177
do_trap_no_signal arch/x86/kernel/traps.c:211 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:260
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:297
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:310
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
RSP: 0018:ffff8801c606e3a0 EFLAGS: 00010282
RAX: 0000000000000026 RBX: 0000000000001401 RCX: 0000000000000000
RDX: 0000000000000026 RSI: ffffc900036fc000 RDI: ffffed0038c0dc68
RBP: ffff8801c606e430 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8801d97f5eba R11: 0000000000000000 R12: ffff8801d5acf73c
R13: 1ffff10038c0dc75 R14: 00000000ffffffff R15: 00000000fffff72f
refcount_add+0x1b/0x60 lib/refcount.c:101
tcp_gso_segment+0x10d0/0x16b0 net/ipv4/tcp_offload.c:155
tcp4_gso_segment+0xd4/0x310 net/ipv4/tcp_offload.c:51
inet_gso_segment+0x60c/0x11c0 net/ipv4/af_inet.c:1271
skb_mac_gso_segment+0x33f/0x660 net/core/dev.c:2749
__skb_gso_segment+0x35f/0x7f0 net/core/dev.c:2821
skb_gso_segment include/linux/netdevice.h:3971 [inline]
validate_xmit_skb+0x4ba/0xb20 net/core/dev.c:3074
__dev_queue_xmit+0xe49/0x2070 net/core/dev.c:3497
dev_queue_xmit+0x17/0x20 net/core/dev.c:3538
neigh_hh_output include/net/neighbour.h:471 [inline]
neigh_output include/net/neighbour.h:479 [inline]
ip_finish_output2+0xece/0x1460 net/ipv4/ip_output.c:229
ip_finish_output+0x85e/0xd10 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:238 [inline]
ip_output+0x1cc/0x860 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:459 [inline]
ip_local_out+0x95/0x160 net/ipv4/ip_output.c:124
ip_queue_xmit+0x8c6/0x18e0 net/ipv4/ip_output.c:504
tcp_transmit_skb+0x1ab7/0x3840 net/ipv4/tcp_output.c:1137
tcp_write_xmit+0x663/0x4de0 net/ipv4/tcp_output.c:2341
__tcp_push_pending_frames+0xa0/0x250 net/ipv4/tcp_output.c:2513
tcp_push_pending_frames include/net/tcp.h:1722 [inline]
tcp_data_snd_check net/ipv4/tcp_input.c:5050 [inline]
tcp_rcv_established+0x8c7/0x18a0 net/ipv4/tcp_input.c:5497
tcp_v4_do_rcv+0x2ab/0x7d0 net/ipv4/tcp_ipv4.c:1460
sk_backlog_rcv include/net/sock.h:909 [inline]
__release_sock+0x124/0x360 net/core/sock.c:2264
release_sock+0xa4/0x2a0 net/core/sock.c:2776
tcp_sendmsg+0x3a/0x50 net/ipv4/tcp.c:1462
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:763
sock_sendmsg_nosec net/socket.c:632 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:642
___sys_sendmsg+0x31c/0x890 net/socket.c:2048
__sys_sendmmsg+0x1e6/0x5f0 net/socket.c:2138
Fixes: 14afee4b60 ("net: convert sock.sk_wmem_alloc from atomic_t to refcount_t")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the following PEAK-System CAN FD interfaces:
PCAN-cPCIe FD CAN FD Interface for cPCI Serial (2 or 4 channels)
PCAN-PCIe/104-Express CAN FD Interface for PCIe/104-Express (1, 2 or 4 ch.)
PCAN-miniPCIe FD CAN FD Interface for PCIe Mini (1, 2 or 4 channels)
PCAN-PCIe FD OEM CAN FD Interface for PCIe OEM version (1, 2 or 4 ch.)
PCAN-M.2 CAN FD Interface for M.2 (1 or 2 channels)
Like the PCAN-PCIe FD interface, all of these boards run the same IP Core
that is able to handle CAN FD (see also http://www.peak-system.com).
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
SUN4Is CAN IP has a 64 byte deep FIFO buffer. If the buffer is not
drained fast enough (overrun) it's getting mangled. Already received
frames are dropped - the data can't be restored.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The D_CAN controller doesn't provide a triple sampling mode, so don't set
the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling
triple sampling is a no-op.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.6
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit:
9a93848fe7 ("x86/debug: Implement __WARN() using UD0")
turned warnings into UD0, but the fixup code only runs after the
notify_die() chain. This is a problem, in particular, with kgdb,
which kicks in as if it was a BUG().
Fix this by running the fixup code before the notifier chain in
the invalid op handler path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Ilya Dryomov <idryomov@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: <stable@vger.kernel.org> # v4.12+
Link: http://lkml.kernel.org/r/20170724100428.19173-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is to prevent the case of working with a single MPWQE
(1 WQE is always reserved as RQ is linked-list).
When the WQE is fully consumed, HW should still have available buffer
in order not to drop packets.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when dma mapping fails, put_page is called,
but the page is not set to null. Later, in the page_reuse treatment in
mlx5e_free_rx_descs(), mlx5e_page_release() is called for the second time,
improperly doing dma_unmap (for a non-mapped address) and an extra put_page.
Prevent this by nullifying the page pointer when dma_map fails.
Fixes: accd588332 ("net/mlx5e: Introduce RX Page-Reuse")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
napi->poll can be called with budget 0, e.g. in netpoll scenarios
where the caller only wants to poll TX rings
(poll_one_napi@net/core/netpoll.c).
The below commit changed RX polling from "while" loop to "do {} while",
which caused to ignore the initial budget and handle at least one RX
packet.
This fixes the following warning:
[ 2852.049194] mlx5e_napi_poll+0x0/0x260 [mlx5_core] exceeded budget in poll
[ 2852.049195] ------------[ cut here ]------------
[ 2852.049195] WARNING: CPU: 0 PID: 25691 at net/core/netpoll.c:171 netpoll_poll_dev+0x18a/0x1a0
Fixes: 4b7dfc9925 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After the panic teardown firmware command, health_care detects the error
in PCI bus and calls the mlx5_pci_err_detected. This health_care flow is
no longer needed because the panic teardown firmware command will bring
down the PCI bus communication with the HCA.
The solution is to cancel the health care timer and its pending
workqueue request before sending panic teardown firmware command.
Kernel trace:
mlx5_core 0033:01:00.0: Shutdown was called
mlx5_core 0033:01:00.0: health_care:154:(pid 9304): handling bad device here
mlx5_core 0033:01:00.0: mlx5_handle_bad_state:114:(pid 9304): NIC state 1
mlx5_core 0033:01:00.0: mlx5_pci_err_detected was called
mlx5_core 0033:01:00.0: mlx5_enter_error_state:96:(pid 9304): start
mlx5_3:mlx5_ib_event:3061:(pid 9304): warning: event on port 0
mlx5_core 0033:01:00.0: mlx5_enter_error_state:104:(pid 9304): end
Unable to handle kernel paging request for data at address 0x0000003f
Faulting instruction address: 0xc0080000434b8c80
Fixes: 8812c24d28 ('net/mlx5: Add fast unload support in shutdown flow')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
list_splice_init initializing waiting_events_list after splicing it to
temp list, therefore we should loop over temp list to fire the events.
Fixes: 4ca637a20a ("net/mlx5: Delay events till mlx5 interface's add complete for pci resume")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
register_sysctl() has been around for five years with commit
fea478d410 ("sysctl: Add register_sysctl for normal sysctl users") but
now that arm64 started using it, I ran into a compile error:
arch/arm64/kernel/armv8_deprecated.c: In function 'register_insn_emulation_sysctl':
arch/arm64/kernel/armv8_deprecated.c:257:2: error: implicit declaration of function 'register_sysctl'
This adds a inline function like we already have for
register_sysctl_paths() and register_sysctl_table().
Link: http://lkml.kernel.org/r/20171106133700.558647-1-arnd@arndb.de
Fixes: 38b9aeb32f ("arm64: Port deprecated instruction emulation to new sysctl interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "Luis R. Rodriguez" <mcgrof@kernel.org>
Cc: Alex Benne <alex.bennee@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
