Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems cannot operate mt9v022 in normal mode and use
only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024
(TN-09-225) describes required register settings when configuring the
snapshot operation. The snapshot mode requires that certain automatic
functions of the image sensor should be disabled or set to fixed values.
According to the TechNote bit 2 and bit 9 in the register 0x20 must be
set in snapshot mode and unset for normal operation. This applies for
mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on
sensor chip version.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add controls for horizontal and vertical blanking. Also add an error
message for case that the control handler init failed. Since setting
the blanking registers is done by controls now, we shouldn't change
these registers outside of the control function. Use v4l2_ctrl_s_ctrl()
to set them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the result of experimenting with the SpeedLink VAD Laplace webcam.
The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by
analyzing USB-logs of this device running on MS Windows.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Try reading on video device. If the camera bus driver supports reading
we can try it and return the result. Also add a debug line.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mx1_camera driver has been broken for a few release cycles since
commit 6bd0812 (dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c).
It seems there is no one even compile tested it since then, as doing
so will end up with the following error.
CC drivers/media/platform/soc_camera/mx1_camera.o
In file included from drivers/media/platform/soc_camera/mx1_camera.c:44:0:
arch/arm/mach-imx/include/mach/dma-mx1-mx2.h:8:25: fatal error: mach/dma-v1.h: No such file or directory
It seems there is no one being interested in bringing it back to
work [1] so far. Let's mark it BROKEN.
[1] https://lkml.org/lkml/2012/2/9/171
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the MT9V022_TOTAL_SHUTTER_WIDTH register is controlled in manual
mode by V4L2_CID_EXPOSURE control, it shouldn't be written directly in
mt9v022_s_crop(). In manual mode this register should be set to the
V4L2_CID_EXPOSURE control value. Changing this register directly and
outside of the actual control function means that the register value
is not in sync with the corresponding control value. Thus, the following
problem is observed:
- setting this control initially succeeds
- VIDIOC_S_CROP ioctl() overwrites the MT9V022_TOTAL_SHUTTER_WIDTH
register
- setting this control to the same value again doesn't
result in setting the register since the control value
was previously cached and doesn't differ
Remove MT9V022_TOTAL_SHUTTER_WIDTH register setting in mt9v022_s_crop()
and add a comment explaining why it is not needed in manual mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock on the error handle path in function
mx2_start_streaming().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in omap1_camera. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.set_crop() implementation in mx1_camera is identical with the default.
Remove the copy to switch to using the default stab.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx2_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx3_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in pxa_camera.c. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_mobile_ceu_camera. Fix them by cleanly separating writable
and read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_vou. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
int sys32_rt_sigprocmask(int how, compat_sigset_t __user *set, compat_sigset_t __user *oset,
unsigned int sigsetsize)
{
sigset_t old_set, new_set;
int ret;
if (set && get_sigset32(set, &new_set, sigsetsize))
...
static int
get_sigset32(compat_sigset_t __user *up, sigset_t *set, size_t sz)
{
compat_sigset_t s;
int r;
if (sz != sizeof *set) panic("put_sigset32()");
In other words, rt_sigprocmask(69, (void *)69, 69) done by 32bit process
will promptly panic the box.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check overlay_ops is not NULL as checked in the previous 'if' condition.
Fixes the following smatch error:
drivers/gpu/drm/exynos/exynos_drm_encoder.c:509 exynos_drm_encoder_plane_disable()
error: we previously assumed 'overlay_ops' could be null (see line 499)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixes the following sparse warnings:
drivers/gpu/drm/exynos/exynos_drm_fimd.c:65:25: warning:
symbol 'exynos4_fimd_driver_data' was not declared. Should it be static?
drivers/gpu/drm/exynos/exynos_drm_fimd.c:69:25: warning:
symbol 'exynos5_fimd_driver_data' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Chagelog v2:
Move encoder's dpms updating into exynos_drm_encoder_commit
function because when crtc's dpms is updated, encoder's dpms
is updated also. This would induce the issue that encoder
isn't disabled after crtc is disabled.
Changelog v1:
This patch fixes a issue that overlay data aren't applied
to real hardware when dpms off goes to on after setcrtc
was requested like below,
dpms off -> setcrtc -> dpms off -> dpms on
For this, it makes encoder's dpms to be updated when
setcrtc is requested.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
plane->fb will be set to new fb after update_plane callback is called
by drm_mode_set_plane()
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
With iommu, buffer->dma_addr has device addres so this patch
fixes for physical address to be set to fix.smem_start always.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
When a write to a replacement device completes, we carefully
and correctly found the rdev that the write actually went to
and the blithely called rdev_dec_pending on the primary rdev,
even if this write was to the replacement.
This means that any writes to an array while a replacement
was ongoing would cause the nr_pending count for the primary
device to go negative, so it could never be removed.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a replacement operation completes there is a small window
when the original device is marked 'faulty' and the replacement
still looks like a replacement. The faulty should be removed and
the replacement moved in place very quickly, bit it isn't instant.
So the code write out to the array must handle the possibility that
the only working device for some slot in the replacement - but it
doesn't. If the primary device is faulty it just gives up. This
can lead to corruption.
So make the code more robust: if either the primary or the
replacement is present and working, write to them. Only when
neither are present do we give up.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
The ixp4xx queue manager uses "const struct qmgr_regs __iomem *" as the
type for a pointer that is passed to __raw_writel, which is not
allowed because of the const-ness.
Dropping the 'const' keyword fixes the problem. While we're here,
let's also drop the useless type cast.
Without this patch, building ixp4xx_defconfig results in:
In file included from arch/arm/mach-ixp4xx/ixp4xx_qmgr.c:15:0:
arch/arm/mach-ixp4xx/include/mach/qmgr.h: In function 'qmgr_put_entry':
arch/arm/mach-ixp4xx/include/mach/qmgr.h:96:2: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
In file included from drivers/net/ethernet/xscale/ixp4xx_eth.c:41:0:
arch/arm/mach-ixp4xx/include/mach/qmgr.h: In function 'qmgr_put_entry':
arch/arm/mach-ixp4xx/include/mach/qmgr.h:96:2: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
arch/arm/mach-ixp4xx/ixp4xx_qmgr.c: In function 'qmgr_set_irq':
arch/arm/mach-ixp4xx/ixp4xx_qmgr.c:41:9: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
It doesn't make much sense to map QMgr dynamically - we almost always need it
and the static mapping will be needed for little-endian data-coherent operation
(to make QMgr region value-coherent).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Alex writes:
A couple more small fixes for 3.7:
- another evergreen_mc fix
- add an AGP quirk for an old RV250
- new pci id.
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
nouveau: one more regression fix.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: use the correct fence implementation for nv50
Some more misc fallout from nouveau rework.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
Only compile time tested, noticed nv50_fence_create was never used,
so fix this. This will probably fix vblank on nv50 cards.
Hopefully this is still in time for 3.7 final release.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The commit 81732c3b2f
("Fix line garbage in virtual console on command line edition")
made a regression with some machines: some characters were not erased
after line edition.
This patch adjusts the number of moved characters and the size of the
region to be updated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen Gang reports:
the length of nla_data(cda[CTA_TIMEOUT_NAME]) is not limited in server side.
And indeed, its used to strcpy to a fixed-sized buffer.
Fortunately, nfnetlink users need CAP_NET_ADMIN.
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Due to the missing ininitalization at adding/deleting entries, when
a plain_ip,port,net element was the object, multiple elements were
added/deleted instead. The bug came from the missing dangling
default initialization.
The error-prone default initialization is corrected in all hash:* types.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There have been some 3.7-rc reports of vm issues, including some kswapd
bugs and, more importantly, some memory "leaks":
http://www.spinics.net/lists/linux-mm/msg46187.htmlhttps://bugzilla.kernel.org/show_bug.cgi?id=50181
Commit 1fb3f8ca0e ("mm: compaction: capture a suitable high-order page
immediately when it is made available") took split_free_page() and
reused it for the compaction code. It does something curious with
capture_free_page() (previously known as split_free_page()):
int capture_free_page(struct page *page, int alloc_order,
...
__mod_zone_page_state(zone, NR_FREE_PAGES, -(1UL << order));
- /* Split into individual pages */
- set_page_refcounted(page);
- split_page(page, order);
+ if (alloc_order != order)
+ expand(zone, page, alloc_order, order,
+ &zone->free_area[order], migratetype);
Note that expand() puts the pages _back_ in the allocator, but it does
not bump NR_FREE_PAGES. We "return" 'alloc_order' worth of pages, but
we accounted for removing 'order' in the __mod_zone_page_state() call.
For the old split_page()-style use (order==alloc_order) the bug will not
trigger. But, when called from the compaction code where we
occasionally get a larger page out of the buddy allocator than we need,
we will run in to this.
This patch simply changes the NR_FREE_PAGES manipulation to the correct
'alloc_order' instead of 'order'.
I've been able to repeatedly trigger this in my testing environment.
The amount "leaked" very closely tracks the imbalance I see in buddy
pages vs. NR_FREE_PAGES. I have confirmed that this patch fixes the
imbalance
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) inet6_csk_update_pmtu() must return NULL or non-NULL, so translate
ERR_PTR to NULL, as needed. Fix from Eric Dumazet.
2) Fix copy&paste error in IRDA sir_dev ->set_speed method invocation,
it was testing the NULL'ness of a different method to guard the
call. Fix from Alexander Shiyan.
3) Fix build regression of xilinx driver, from Jeff Mahoney.
4) Make XEN netfront (like XEN netback) handle compound pages in SKBs
properly. From Ian Campbell.
5) Fix inverted logic of team_dev_queue_xmit() return value checks,
from Jiri Pirko and Dan Carpenter.
6) dma_poll_create() no longer allows a NULL device argument, breaking
both ixp4xx drivers. Fix from Xi Wang.
7) ne2000 driver doesn't hook up the parent device properly, breaking
udev matching. Fix from Alan Cox.
8) Locking and memory leak fixes in Near Field Communications layer.
From Thierry Escande, Szymon Janc, and Waldemar Rymarkiewicz.
9) sis900 resume regression, sis900_set_mode() is being called with the
iomem pointer instead of the expected device private. Fix from
Francois Romieu.
10) Fix IBSS regression caused by uninitializing the ibss-internals
before performing an emptyness check, from Simon WUnderlich.
11) Fix SNIFFER mode regression in iwlwifi driver, from Johannes Berg.
12) Fix task wedges in mwifiex_cmd_timeout_func(), from Bing Zhao.
13) Add back wireless sysfs directory, too much stuff depends upon it
being there (actually I'd say it never should have been removed to
begin with). From Johannes Berg.
14) Fix hang introduced by suspend/resume changes in ath9k. Fix from
Sujith Manoharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
team: bcast: convert return value of team_dev_queue_xmit() to bool correctly
bonding: Bonding driver does not consider the gso_max_size/gso_max_segs setting of slave devices.
xen/netfront: handle compound page fragments on transmit
net: fix build failure in xilinx
irda: sir_dev: Fix copy/paste typo
ipv6: fix inet6_csk_update_pmtu() return value
ixp4xx_hss: avoid calling dma_pool_create() with NULL dev
ixp4xx_eth: avoid calling dma_pool_create() with NULL dev
ne2000: add the right platform device
of/net/mdio-gpio: Fix pdev->id issue when using devicetrees.
NFC: Fix pn533 target mode memory leak
NFC: pn533: Fix mem leak in pn533_in_dep_link_up
NFC: pn533: Fix use after free
NFC: pn533: Fix missing lock while operating on commands list
NFC: Fix nfc_llcp_local chained list insertion
ath9k_hw: Fix regression in device reset
sis900: fix sis900_set_mode call parameters.
iwlwifi: don't WARN when a non empty queue is disabled
wireless: add back sysfs directory
mwifiex: report error to MMC core if we cannot suspend
...
commit 9e44476851
MD: raid5 avoid unnecessary zero page for trim
change raid5 to clear R5_Discard when the complete request is
handled rather than when submitting the per-device discard request.
However it did not clear R5_Discard for the parity device.
This means that if the stripe_head was reused before it expired from
the cache, the setting would be wrong and a hang would result.
Also if the R5_Uptodate bit happens to be set, R5_Discard again
won't be cleared. But R5_Uptodate really should be clear at this point.
So make sure R5_Discard is cleared in all cases, and clear
R5_Uptodate when a 'discard' completes.
Signed-off-by: NeilBrown <neilb@suse.de>
stripe_handle.
The chunk of code in stripe_handle which responds to a
*_result value in reconstruct_state is really the completion
of some processing that happened outside of handle_stripe
(possibly asynchronously) and so should be one of the first
things done in handle_stripe().
After the next patch it will be important that it happens before
handle_stripe_clean_event(), as that will clear some dev->flags
bit that this code tests.
Signed-off-by: NeilBrown <neilb@suse.de>
essential pins.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pJyU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.
* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
Commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code) have enabled the
pendown GPIO debounce time setting by the below sequence:
gpio_request_one()
gpio_set_debounce()
gpio_free()
It also revealed a bug in the OMAP GPIO handling code which prevented
the GPIO debounce clock to be disabled and CORE transition to low power
states.
Commit c9c55d9 (gpio/omap: fix off-mode bug: clear debounce settings on
free/reset) fixes the OMAP GPIO handling code by making sure that the
GPIO debounce clock gets disabled if no GPIO is requested from current
bank.
While fixing the OMAP GPIO handling code (in the right way), the above
commit makes the gpio_request->set_debounce->free sequence invalid as
after freeing the GPIO, the debounce settings are lost.
Fix the debounce settings by moving the debounce initialization to the
actual GPIO requesting code - the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STDI block may measure wrong values, especially for lcvs and lcf. If the
driver can not find any valid timing, the STDI block is restarted to measure
the video timings again. The function will return an error, but the restart of
STDI will generate a new STDI interrupt and the format detection process will
restart.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
