Update ata_scsi_error() to handle PMP links. As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.
printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links. If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to keep track of new changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use builtin statistics structure from net device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put initialization in sequential order (same as other constants).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure PCI register for PHY power gets set correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure and not dump reserved areas of device space.
Touching some of these causes machine check exceptions on boards
like D-Link DGE-550SX.
Coding note, used a complex switch statement rather than bitmap
because it is easier to relate the block values to the documentation
rather than looking at a encoded bitmask.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Allow a fixed framebuffer address to be assigned to the framebuffer device
instead of allocating the framebuffer from the consistent memory pool.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some custom implementations of the xilinx fb can use resolutions other
than 640x480. This patch allows the resolution to be specified in the
device tree or the xilinx_platform_data structure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The call to xilinxfb_assign is getting unwieldy when adding features
to the Xilinx framebuffer driver. Change xilinxfb_assign() to accept
a pointer to a xilinxfb_platform_data structure to prepare for adding
additition configuration options.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
ide: use only ->set_pio_mode method for programming PIO modes (take 2)
sis5513: don't change UDMA settings when programming PIO
it8213/piix/slc90e66: don't change DMA settings when programming PIO
alim15x3: PIO mode setup fixes
siimage: fix ->set_pio_mode method to select PIO data transfer
cs5520: don't enable VDMA in ->speedproc
sc1200: remove redundant warning message from sc1200_tune_chipset()
ide-pmac: PIO mode setup fixes (take 3)
icside: fix ->speedproc to return on unsupported modes (take 5)
sgiioc4: use ide_tune_dma()
amd74xx/via82cxxx: use ide_tune_dma()
ide: add ide_set{_max}_pio() (take 4)
ide: Kconfig face-lift
ide: move ide_rate_filter() calls to the upper layer (take 2)
sis5513: add ->udma_filter method for chipset_family >= ATA_133
ide: mode limiting fixes for user requested speed changes
ide: add missing ide_rate_filter() calls to ->speedproc()-s
ide: call udma_filter() before resorting to the UltraDMA mask
ide: make jmicron match vendor and device class
pdc202xx_new: switch to using pci_get_slot() (take 2)
...
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Update Cobalt Qube series front LED support
leds: Add Cobalt Raq series LEDs support
leds: Rename leds-cobalt driver
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Convert corgi backlight driver into a more generic driver
backlight: Add Samsung LTV350QV LCD driver
backlight: Fix cr_bllcd allocations and error paths
backlight/leds: Make two structs static
* 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block: (37 commits)
[BLOCK] Fix failing compile with BLK_DEV_IO_TRACE=n
compat_ioctl: move floppy handlers to block/compat_ioctl.c
compat_ioctl: move cdrom handlers to block/compat_ioctl.c
compat_ioctl: move BLKPG handling to block/compat_ioctl.c
compat_ioctl: move hdio calls to block/compat_ioctl.c
compat_ioctl: handle blk_trace ioctls
compat_ioctl: add compat_blkdev_driver_ioctl()
compat_ioctl: move common block ioctls to compat_blkdev_ioctl
Sysace: Don't enable IRQ until after interrupt handler is registered
Sysace: sparse fixes
Sysace: Minor coding convention fixup
drivers/block/umem: use DRIVER_NAME where appropriate
drivers/block/umem: trim trailing whitespace
drivers/block/umem: minor cleanups
drivers/block/umem: use dev_printk()
drivers/block/umem: move private include away from include/linux
Sysace: Labels in C code should not be indented.
Sysace: Add of_platform_bus binding
Sysace: Move IRQ handler registration to occur after FSM is initialized
Sysace: minor rework and cleanup changes
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (74 commits)
Blackfin serial driver: pending a unique anomaly id, tie the break flood issue to ANOMALY_05000230
blackfin enable arbitary speed serial setting
Blackfin arch: Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT and DEBUG_KERNEL_START
Blackfin arch: fix typo in register name
Blackfin arch: trim the Blackfin arch MAINTAINERS list
Blackfin arch: fix bug libstdc++ calling writev with an iovec containing { NULL, 0 } fails on Blackfin
Blackfin arch: Export strcpy - occasionally get module link failures otherwise
Blackfin arch: the load address is not safe to point to as a workaround for ANOMALY 05000281
Blackfin arch: show_mem can not be marked as init, since it is called during OOM condition
Blackfin arch: flush/inv the correct range when using write back cache and fix bugs find by dmacopy
Blackfin arch: update kgdb patch
Blackfin arch: Comply with revised Anomaly Workarounds for BF533 05000311 and BF561 05000323
Blackfin arch: Print out debug info, as early as possible
Blackfin arch: Enable earlyprintk earlier - so any error after our interrupt tables are set up will print out
Blackfin arch: fix endless loop bug when a double fault happens
Blackfin arch: Initial patch to add earlyprintk support
Blackfin arch: add TWIx_REGBASE and SPIx_REGBASE to specific CPU header files, use the new REGBASE for board platform resources
Blackfin arch: modify the insX/outsX and dma_insX/dma_outsX to be compatible with other archs
Blackfin arch: add more common defines for output sections
Blackfin arch: cleanup IO and DMA_IO API function definitions according to other arches
...
Handle the corner case where budget is exhausted correctly.
And save unnecessary read of index register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.
v2:
* Fix pmac_ide_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return failure in ->speedproc method for unsupported/invalid transfer
modes passed from user-space (fixes theoretical OOPS in ali_tune_pio()
and/or setting random PIO timings on host controller + disabling UDMA
bit + setting unsupported/invalid transfer mode on the device).
* Don't disable UDMA bit when programming PIO modes.
* Add FIXME about DMA timings never being set.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio()
(->set_pio_mode method) so the controller is always programmed correctly for
PIO transfers (this is important if DMA is not going to be used).
* Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset().
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is no need to do it in cs5520_tune_chipset() (->speedproc method)
since it is correctly handled by cs5520_dma_on() (->ide_dma_on method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_config_drive_speed() called by sc1200_set_xfer_mode() already gives
a meaningful warning message in case of failure.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add { 0, 0 } entry to {kauai,shasta}_pio_timings[] so kauai_lookup_timing()
always returns a valid PIO timing (fixes PIO timing not being set for devices
with minimum PIO cycle <= 120ns).
* Add setting transfer mode on the device to pmac_ide_set_pio_mode().
* Fix pmac_ide_set_pio() to always program chipset for given PIO timing instead
of only when the device we want to program PIO timing for is the currently
selected one.
* Now that pmac_ide_set_pio() is fixed there is no need to set transfer mode
on the device and program chipset for PIO in pmac_ide_tune_chipset()
(returning 0 == success is not entirely correct but is OK for now since
the upper layers are only checking ->speedproc return value for DMA modes).
v2:
* s/speed/XFER_PIO_0 + pio/ in pmac_ide_set_pio_mode() so it actually compiles.
* Removal of kauai_lookup_timing() return value checking went to separate patch.
v3:
* Use XFER_PIO_0 not XFER_PIO. (Noticed by Ben)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* All other implementations of ->speedproc return zero on success
and non-zero on failure. Currently it doesn't matter for icside host
driver and isn't a bug per se since:
- ide_set_xfer_rate() return value is ignored by all IDE core users
- icside doesn't (yet!) use ide_tune_dma() in icside_dma_check()
but sooner or later we will need to fix anyway - so lets do it now.
* icside_set_speed() happily accepts unsupported transfer modes which
results in drive->drive_data being set to the maximum value (480)
and drive->current_speed being set to the unsupported transfer mode.
Fix it.
v2:
* The initial version of the patch was broken because it didn't take into
the account (the different from usual) return values of icside_set_speed()
(Noticed by Russell).
v3:
* Remove no longer needed initialization/checking of cycle_time
(Noticed by Sergei).
* No need to set drive->drive_data if DMA is not going to be used
(Noticed by Sergei).
* Remove incorrect setting of drive->current_speed
(Noticed by Sergei).
* Move ide_config_drive_speed() at the end of icside_set_speed().
v4:
* If DMA mode is not found in icside_dma_check() then just return "-1" and
don't call icside_set_speed() (v3 got it wrong and "1" was returned instead).
v5:
* Return "-1"/"0" in icside_set_speed() instead of icside_dma_check() return
value (just like it was before this patch).
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DRV_NAME define and use it instead of sgiioc4_chipset.name.
* Remove no longer needed sgiioc4_chipset.
* Remove needless clearing of ->atapi_dma from ide_dma_sgiioc4().
* Fix ide_dma_sgiioc4() to return success/failure. Check return value in
sgiioc4_ide_setup_pci_device() and set hwif->autodma accordingly. Also add
missing setting of drive->autodma.
* Add sgiioc4_speedproc() (implementation of ->speedproc method).
* Fix ->mwdma_mask (MWDMA2 mask is 0x04 not 0x02) and remove incorrect
->swdma_mask. Also remove needless initialization of ->ultra_mask.
* Use ide_tune_dma() in sgiioc4_ide_dma_check(), this fixes following bugs:
- DMA capability bit not being checked on the device
- DMA blacklist not being checked
- MWDMA2 mode support by device not being checked
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ide_tune_dma() in amd74xx/via82cxxx driver, this fixes following bugs:
- DMA capability bit not being checked on the device
- DMA blacklist not being checked
- DMA mode being programmed even if drive->autodma == 0
(thus possibly destroying PIO timings)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert config options for PCI host drivers to select BLK_DEV_IDEPCI.
* Same for BLK_DEV_IDEDMA_PCI and PCI DMA host drivers, also make this
config option select BLK_DEV_IDEPCI.
* Remove no longer needed help for BLK_DEV_IDEPCI and BLK_DEV_IDEDMA_PCI.
* Remove redundant IDE_CHIPSETS config option.
As a result of this patch users have now three less config options
to worry about and can just select host drivers that they need
(IDE config menu is "flatter").
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
