Users can apply i/o in the wrong direction on an
endpoint to stall it. In case there is an error
that does not allow the endpoint to be stalled,
we want the user to know.
An operation to stall the endpoint will return
EBADMSG if successful, EAGAIN if there are still
queued requests, and other errors depending on
the underlying implementation.
Also remove the conditional since it is always true.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If a phy is specified in the device tree node, get it and use it.
This was based on a patch by:
"Srinath Mannam <srinath.mannam@broadcom.com>"
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many ARM based Broadcom STB SoC's have a USB BDC controller so
enable this driver for these systems.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch essentially clears the port status change bits at the
correct times. It is necessary because the driver was not handling
the change bits correctly for events during device
connection/disconnection and bus enumeration. So, one of them (PCC)
was left stuck sometimes causing the "xsf for ep not enabled"
error we get on first connection. This was found by the Android team.
This was debugged and fixed by Sasi Kumar.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Based on a previous commit by Danesh Petigara <dpetigara@broadcom.com>
that added resume to solve the following problem:
"The BDC driver will fail after resuming from S3 suspend and this
will cause any upper layer gadget driver to fail."
This commit also adds support for suspend and manages the clock during
suspend/resume.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allows Device Tree probing
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Newer SoC's have added a BDC clock to the Device Tree, so get
and enable it.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The BDC endpoint status registers 0-7 were originally each going
to be an array of regsiters. This was later changed to being a
single register. The register definitions are being changed from:
"#define BDC_EPSTS0(n) (0x60 + (n * 0x10))"
to
"#define BDC_EPSTS0 0x60"
to reflect this change and to avoid future coding mistakes.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This adds 3 new options to the RNDIS gadget function configs. It allows
overriding the default USB interface class/subclass/protocol.
The motivation for this is that if you set the values to "ef" (Misc),
"04" (RNDIS), "01" (Ethernet) respectively, then the device will be
recognized by the rndiscmp.inf file in Windows Vista and newer and will
cause Windows to load the correct RNDIS driver without the need for a
custom (signed) .inf file.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case hcd autosuspend is enabled, the hcd will enter L2 state
if no device connected. But if the controller works in otg mode, the
gadget driver still works in L0 state if connected with host. This
may result in transfer fail when gadget enqueue new request but the
hcd driver has set the global state into L2. This patch prevent the
hcd enter L2 state if the controller work in device mode.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that the spin_lock_init() is not called
for almost all pipes. Otherwise, the lockdep output the following
message when we connect a usb cable using g_ncm:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the SG case this is already handled since a non-zero
request->num_mapped_sgs is a clear indicator that dma_map_sg()
had been called. While it would be nice to do the same for the
singly mapped case by simply checking for non-zero request->dma,
it's conceivable that 0 is a valid dma_addr_t handle. Hence add
a flag 'dma_mapped' to struct usb_request and use this to
determine the need to call dma_unmap_single(). Otherwise, if a
request is not DMA mapped then the result of calling
usb_request_unmap_request() would safely be a no-op.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB gadget serial console works on functions other than the legacy
configurations. Let the user enable it when using any function that
uses the serial utilities.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The header clk-provider.h is there for clock drivers (providers) to
include, not client drivers (consumers). That said,
of_clk_get_parent_count() is a helper function for clock providers, not
a clk API for consumers.
Let's replace of_clk_get_parent_count() with of_count_phandle_with_args()
call, so that we can remove the include of clk-provider.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currenly, f_midi_free uses snd_card_free, which will wait
until the user has released the sound card before
returning. However, if the user doesn't release the sound
card, then f_midi_free can block for an arbitrary amount
of time, which also blocks any gadget operations on that
thread.
Instead, we can use snd_card_free_when_closed which returns
before all handles are released. Since f_midi can be
accessed through rmidi if usb_put_function is called before
release_card_device, add refcounting to f_midi_free and
have rawmidi's private free call it. The f_midi memory
is only kfreed when usb_put_function and release_card_device
have both been called.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add super speed descriptors for f_midi.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The while loop never terminates because the loop counter i is never
decremented. Fix this by decrementing i.
Detected by CoverityScan, CID#751073 ("Infinite Loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These snd_rawmidi_ops structures are only passed as the third
argument of snd_rawmidi_set_ops. This argument is const, so the
snd_rawmidi_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The mtu3 driver is a generic driver for MediaTek usb3 DRD IP, add
a generic compatible to avoid confusion when support new SoCs but
use a compatible with specific SoC's name "mt8173".
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current f_hid driver doesn't handle GET_PROCOTOL and
SET_PROCOTOL requests, which are required to operate HID
gadgets in BOOT mode. This patch implements this feature for
devices that have the same implementation for REPORT and BOOT mode
so that these devices are recognized by older BIOSes.
Signed-off-by: Abdulhadi Mohamed <abdulahhadi2@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Ip sleep will auto exit if vbus comparison circuit of u2 phy is
disabled when system tries to enter suspend mode, so get vbus-valid
status from mac but not from u2 phy when enable DRD mode to fix
the issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when the device is reset by host, the status of u1_enable and
u2_enable should also be restored to default value.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the delayed status handling. This is used by mass storage etc to
gain some extra time to setup its internal status before it can proceed
further requests, and once the gadget is ready, it will enqueue an
empty packet which is used for synchronization.
The issue may happen on some FGPA platform with very low cpu frequency.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Using devm_ioremap_resource() can make the code simpler, as it
already does the resource NULL check.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
qe_ep0_desc is only passed as the second argument to qe_ep_init, which is
const, so qe_ep0_desc can be const too.
Done with the help of Coccinelle.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car M3-W. This patch also adds R-Car
Gen3 generic version's compatible and changes ".compatible" in
the usb3_of_match from "renesas,r8a7796-usb3-peri" to
"renesas,rcar-gen3-usb3-peri".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car H3 ES2.0. Since this SoC revision
doesn't need workaround for vbus detection and number of ramif is
increased. So, this driver uses soc_device_match() to detect it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds debugfs to set the "b-device" mode for using a board
which is not connected to the ID pin (e.g. CN11 on Salvator-X).
If we want to use peripheral mode on such a board, we have to disable
VBUS output first. So, this patch can set such a mode as the following:
# mount -t debugfs none /sys/kernel/debug
# modprobe renesas_usb3
# modprobe g_mass_storage file=/dev/shm/test.bin
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Provides a new vbus debugfs interface used to turn on/off vbus
regulator, it also can be used to get/put reference count of
vbus, due to sometimes we need keep it alive when manually switch
mtu3 to device mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For 66AK2Gx there is a requirement to use PM Runtime to properly manage
clocks and the power domains. Therefore, add PM runtime support. Remove
legacy clock api's calls since other users of this driver worked without
these clock apis calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
platform_get_irq() returns an error code, but the dwc3-omap driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_pm_ops is not supposed to change at runtime. Marking it constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
platform_get_irq() returns an error code, but the renesas_usb3 driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print error message and propagate the return value of platform_get_irq
on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
Cc: <stable@vger.kernel.org>
Fixes: 0f1d832ed1 ("usb: xhci: Add port test modes support for usb2")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
[code simplification and reworded sidenote in commit message -Mathias]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Reported-by: rocko r <rockorequin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for the current -rc cycle. Only three fixes on dwc3
this time around (proper order for getting a PHY reference, fix for
unmapping DMA and a fix for requesting IRQ on the OMAP glue layer).
Most fixes are on the renesas USB controller, fixing several old bugs
with most going to stable.
dwc2 also learned that it *must* reset USB Address to zero on Reset
interrupts.
Apart from these, some drivers needed HAS_DMA dependency and there's a
sparse warning fix for bdc udc.
-----BEGIN PGP SIGNATURE-----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=eMHd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.13-rc2
First set of fixes for the current -rc cycle. Only three fixes on dwc3
this time around (proper order for getting a PHY reference, fix for
unmapping DMA and a fix for requesting IRQ on the OMAP glue layer).
Most fixes are on the renesas USB controller, fixing several old bugs
with most going to stable.
dwc2 also learned that it *must* reset USB Address to zero on Reset
interrupts.
Apart from these, some drivers needed HAS_DMA dependency and there's a
sparse warning fix for bdc udc.
A gadget driver will not disable eps immediately when ->disconnect()
is called. But, since this driver assumes all eps stop after
the ->disconnect(), unexpected behavior happens (especially in system
suspend).
So, this patch disables all eps in usbhsg_try_stop(). After disabling
eps by renesas_usbhs driver, since some functions will be called by
both a gadget and renesas_usbhs driver, renesas_usbhs driver should
protect uep->pipe. To protect uep->pipe easily, this patch adds a new
lock in struct usbhsg_uep.
Fixes: 2f98382dc ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that some registers may be not initialized
after resume if the USBHSF_RUNTIME_PWCTRL is not set. Otherwise,
if a cable is not connected, the driver will not enable INTENB0.VBSE
after resume. And then, the driver cannot detect the VBUS.
Fixes: ca8a282a53 ("usb: gadget: renesas_usbhs: add suspend/resume support")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that unexpected behavior happens when
both the interrupt handler and renesas_usb3_ep_enable() are called.
In this case, since usb3_start_pipen() checked the usb3_ep->started,
but the flags was not protected. So, this patch protects the flag
by usb3->lock. Since renesas_usb3_ep_enable() for EP0 will be not called,
this patch doesn't take care of usb3_start_pipe0().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
