Pull livepatching fixes from Jiri Kosina:
"Two tiny fixes for livepatching infrastructure:
- extending RCU critical section to cover all accessess to
RCU-protected variable, by Petr Mladek
- proper format string passing to kobject_init_and_add(), by Jiri
Kosina"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: RCU protect struct klp_func all the time when used in klp_ftrace_handler()
livepatch: fix format string in kobject_init_and_add()
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the USB completely because of an unconfigured USB phy, and
I only tested it to make sure the Mentor chips are detected and
clocked without a phy.
After testing the USB with actual devices I noticed a few issues
that should be fixed to avoid confusion:
- The USB id pin on dm8168-evm is hardwired and can be changed
only by software. As there are two USB-A type connectors, let's
start both in host mode instead of otg.
- The Mentor core is configured in such a way on dm8168-evm that
it's not capable of multipoint at least on revision c board
that I have.
- We need ranges for the syscon to properly set up the phy as
children of the SCM syscon area.
- Let's not disable the second interface, the board specific
dts files can do that if really needed. Most boards should
just keep it enabled to ensure the device is idled properly.
Note that also a phy and several musb fixes are still needed to
make the USB to work properly in addition to this fix.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull HID fixes from Jiri Kosina:
- a few fixes to Sony driver (rmmod breakage, spinlock initialization),
by Antonio Ospite, Frank Praznik and Jiri Kosina
- fix for wMaxInputLength handling regression in i2c-hid, by Seth
Forshee
- IRQ safety spinlock fix in sensor hub driver, by Srinivas Pandruvada
- IRQ level sensitivity fix to i2c-hid to be compliant with the spec,
by Mika Westerberg
- a couple device ID additions piggy-backing on top of that
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: microsoft: Add ID for NE7K wireless keyboard
HID: i2c-hid: Limit reads to wMaxInputLength bytes for input events
HID: sony: fix uninitialized per-controller spinlock
HID: sony: initialize sony_dev_list_lock properly
HID: sony: Fix a WARNING shown when rmmod-ing the driver
HID: sensor-hub: correct dyn_callback_lock IRQ-safe change
HID: hid-sensor-hub: Correct documentation
HID: saitek: add USB ID for older R.A.T. 7
HID: i2c-hid: The interrupt should be level sensitive
HID: wacom: Add missing ABS_MISC event and feature declaration for 27QHD
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some bios really like to joke and start the planes at an offset ...
hooray!
Align start and end to fix this.
v2: Fixup calculation of size, spotted by Chris Wilson.
v3: Fix serious fumble I've just spotted.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86883
Cc: stable@vger.kernel.org
Cc: Johannes W <jargon@molb.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-and-tested-by: Johannes W <jargon@molb.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: split WARN_ONs, rebase on v4.0-rc1]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm, it's possible that the interrupt handler is called when the device
is in D3 or some other low-power state. It can be due to another device
that is still in D0 state and shares the interrupt line with i915, or on
some platforms there could be spurious interrupts even without sharing
the interrupt line. The latter case was reported by Klaus Ethgen using a
Lenovo x61p machine (gen 4). He noticed this issue via a system
suspend/resume hang and bisected it to the following commit:
commit e11aa36230
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Jun 18 09:52:55 2014 -0700
drm/i915: use runtime irq suspend/resume in freeze/thaw
This is a problem, since in low-power states IIR will always read
0xffffffff resulting in an endless IRQ servicing loop.
Fix this by handling interrupts only when the driver explicitly enables
them and so it's guaranteed that the interrupt registers return a valid
value.
Note that this issue existed even before the above commit, since during
runtime suspend/resume we never unregistered the handler.
v2:
- clarify the purpose of smp_mb() vs. synchronize_irq() in the
code comment (Chris)
v3:
- no need for an explicit smp_mb(), we can assume that synchronize_irq()
and the mmio read/writes in the install hooks provide for this (Daniel)
- remove code comment as the remaining synchronize_irq() is self
explanatory (Daniel)
v4:
- drm_irq_uninstall() implies synchronize_irq(), so no need to call it
explicitly (Daniel)
Reference: https://lkml.org/lkml/2015/2/11/205
Reported-and-bisected-by: Klaus Ethgen <Klaus@Ethgen.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we walk the list of vma, or even for protecting against concurrent
framebuffer creation, we must hold the struct_mutex or else a second
thread can corrupt the list as we walk it.
Fixes regression from
commit d7f46fc4e7
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Fri Dec 6 14:10:55 2013 -0800
drm/i915: Make pin count per VMA
References: https://bugs.freedesktop.org/show_bug.cgi?id=89085
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When converting from implicitly tracked execlist queue items to ref counted
requests, not all frees of requests were replaced with unrefs, and extraneous
refs/unrefs of contexts were added.
Correct the unbalanced refcount & replace the frees.
Remove a noisy warning when hitting the request creation path.
drm_i915_gem_request and intel_context are both kref reference counted
structures. Upon allocation, drm_i915_gem_request's ref count should be
bumped using kref_init. When a context is assigned to the request,
the context's reference count should be bumped using i915_gem_context_reference.
i915_gem_request_reference will reduce the context reference count when
the request is freed.
Problem introduced in
commit 6d3d8274bc
Author: Nick Hoath <nicholas.hoath@intel.com>
AuthorDate: Thu Jan 15 13:10:39 2015 +0000
drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request
v2: Added comments explaining how the ctx pointer and the request object should
be ref-counted. Removed noisy warning.
v3: Cleaned up the language used in the commit & the header
description (Thanks David Gordon)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88652
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It is a bad idea to export static functions. GCC for some platforms
shows errors like:
error: __ksymtab_azx_get_response causes a section type conflict
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The KSTK_EIP() and KSTK_ESP() macros should return the user program
counter (PC) and stack pointer (A0StP) of the given task. These are used
to determine which VMA corresponds to the user stack in
/proc/<pid>/maps, and for the user PC & A0StP in /proc/<pid>/stat.
However for Meta the PC & A0StP from the task's kernel context are used,
resulting in broken output. For example in following /proc/<pid>/maps
output, the 3afff000-3b021000 VMA should be described as the stack:
# cat /proc/self/maps
...
100b0000-100b1000 rwxp 00000000 00:00 0 [heap]
3afff000-3b021000 rwxp 00000000 00:00 0
And in the following /proc/<pid>/stat output, the PC is in kernel code
(1074234964 = 0x40078654) and the A0StP is in the kernel heap
(1335981392 = 0x4fa17550):
# cat /proc/self/stat
51 (cat) R ... 1335981392 1074234964 ...
Fix the definitions of KSTK_EIP() and KSTK_ESP() to use
task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This
gets the registers from the user context stored after the thread info at
the base of the kernel stack, which is from the last entry into the
kernel from userland, regardless of where in the kernel the task may
have been interrupted, which results in the following more correct
/proc/<pid>/maps output:
# cat /proc/self/maps
...
0800b000-08070000 r-xp 00000000 00:02 207 /lib/libuClibc-0.9.34-git.so
...
100b0000-100b1000 rwxp 00000000 00:00 0 [heap]
3afff000-3b021000 rwxp 00000000 00:00 0 [stack]
And /proc/<pid>/stat now correctly reports the PC in libuClibc
(134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 =
0x3b002280):
# cat /proc/self/stat
51 (cat) R ... 989864576 134320308 ...
Reported-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.9+
Remove a useless pm_runtime_put_sync leading to unbalanced
usage_count.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
The A2Q (Add To Queue) and UPDATE bits are left in their previous state
when resetting the layer.
This lead to weird behavior when enabling the plane again: the framebuffer
previously queued is dequeued and we end up with access to an old memory
region.
Reset those bits when resetting the channel.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- Fix a bug that caused 15% CPU performance drop in Kaveri. This was caused
because we overwritten the initialization of the first pipe (out of eight),
which is dedicated to radeon operation. The fix was tested by Michel Dänzer.
This bug was introduced by a patch I prepared (yeah, my bad) and was merged
to 3.19-rc6. Therefore, I also marked it as Cc:stable.
- Fix sparse warning
* tag 'drm-amdkfd-fixes-2015-02-23' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: don't set get_pipes_num() as inline
drm/amdkfd: Initialize only amdkfd's assigned pipelines
This fixes a bit of fallout that was caused by the atomic modesetting
driver conversion and some last-minute changes in the DRM atomic core.
It also fixes a bug exposed by recent changes in the clock framework
which results in non-working HDMI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJU5eTAAAoJEN0jrNd/PrOhyx0P/0oLSRfqddmgqtWYLG5Xprc5
xwI6N3Elil9dMdl+QnVkh0Bd2dN3QiSobpJlLLu0C4eQwSKNGPKrMITdoz2kxdLm
V2hswNN9iVf/g8ZvR/VoLBYaWSZER9OVgSKx6kqih4X1hJNyGpBlux3MPxWQ2MTC
s3fIq8gdSgxcNwno4R1nfx0SOPxVRPW72qfPsY2hZQFE/6jcZ5k6V6BPqcu69mKz
af8SKrEIXN57Lxq54+qlzVrFxKCzQmj9lLeX3yty9Hj+SBqm0ybQNbnCrJE2Kcsi
xkYhA0JxUerw30sb5HJkvJqmWltxoaf0ZDaQOPd01ZTxIOGpsObN2o3h0lBaVt6G
lSXXKdLF9AFtYHzVJq6L7KkpsOK40fM0tks+K/4lhPRIZmwG7A46hRZbVnJfiCUv
PEYdwzXvNrz6jEACw4Cu986556n3FCeR6Qb/4T3gyCNh9VbICxcOTaDwTalGhw44
eLFEvY1KqmAbQtrf6soRlVcMySZ5QEJAZtRxNsYcjhHCSQOmcx6YIRiOJ2aA+BFe
WjHily2N4g7afetc8TWDkFvf8niLVBiyXisEtX90Ef13LRbHVXAY2b4oKiJN6ljX
kSb1uAG1BbLChETluAAj4CN6QQigzbMYjkW5Zrv9xN/Aj9w52YQK2bW9ydNH3ULW
UofsqSV4zUdXxcY2NSCQ
=PQiO
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.20-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v3.20-rc1
This fixes a bit of fallout that was caused by the atomic modesetting
driver conversion and some last-minute changes in the DRM atomic core.
It also fixes a bug exposed by recent changes in the clock framework
which results in non-working HDMI.
* tag 'drm/tegra/for-3.20-rc1-fixes' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: dc: Move more code into ->init()
drm/tegra: dc: Wire up CRTC parent of atomic state
drm/tegra: dc: Reset state's active_changed field
drm/tegra: hdmi: Explicitly set clock rate
In commit ccfc08655d
Author: Rob Clark <robdclark@gmail.com>
Date: Thu Dec 18 16:01:48 2014 -0500
drm: tweak getconnector locking
We need to extend the locking to cover connector->state reading for
atomic drivers, but the above commit was a bit too eager and also
included the fill_modes callback. Which on i915 on old platforms using
load detection needs to acquire modeset locks, resulting in a deadlock
on output probing.
Reported-by: Marc Finet <m.dreadlock@gmail.com>
Cc: Marc Finet <m.dreadlock@gmail.com>
Cc: robdclark@gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Define the generic R8A7794 parts of the SDHI[012] device nodes.
Based on the orginal patch by Shinobu Uehara <shinobu.uehara.xc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If xfs_trans_reserve fails we don't cancel the transaction,
and we'll leak the allocated transaction pointer.
Spotted by Coverity.
Signed-off-by: Eric Sandeen <ssandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We shouldn't get here with RENAME_EXCHANGE set and no
target_ip, but let's be defensive, because xfs_cross_rename()
will dereference it.
Spotted by Coverity.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
If the default PM domain using PM_CLK is used for PM runtime, the real PM
domain(s) cannot be registered from DT later.
Hence do not enable it when running a multi-platform kernel with genpd
support on an r8a7740. The R-Mobile PM domain driver will take care of
PM runtime management of the module clocks.
The default PM domain is still needed for:
- platforms without genpd support,
- the legacy (non-DT) case, where genpd may take over later, except
for the C5 "always on" PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7790 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7791 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the CAN0 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7790 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure the pinmux on kzm9d to use the serial connector for uart1.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With this information all GPIOs can make use of the PFC functionality.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector
and configure the DISP pin group that drives the HDMI transmitter DE
pin.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
Fixes: 59e79895b9 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
* Correct base address of SD3 div6 clk.
* Update div6 clock node labels
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
This has no run-time affect as the clock nodes are not currently used.
Fixes: 8e181633e6 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7794 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7790 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7794 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specifies clock sources and register bits.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the R2025D real-time clock, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the ADXL345 three-axis digital accelerometer sensor,
which is connected to i2c0.
As trivial i2c devices are matched against the first compatible entry
only, compatibility is declared with "adi,adxl34x" only for now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device needs an interrupt to operate properly. Specify the two
interrupts used on the board.
While at it rename the DT node to accelerometer@1d to describe the
device's function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the AK8975 magnetometer sensor, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Specify the device interrupt to avoid polling for end of conversion.
While at it rename the DT node to compass@c to describe the device's
function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
