Change 'bp_len' type to __u64 to make it work across archs as
the s390 architecture watch point length can be upto 2^64.
reference:
http://lkml.org/lkml/2010/1/25/212
This is an ABI change that is not backward compatible with
the previous hardware breakpoint info layout integrated in this
development cycle, a rebuilt of perf tools is necessary for
versions based on 2.6.33-rc1 - 2.6.33-rc6 to work with a
kernel based on this patch.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "K. Prasad" <prasad@linux.vnet.ibm.com>
Cc: Maneesh Soni <maneesh@in.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin <schwidefsky@de.ibm.com>
LKML-Reference: <20100130045518.GA20776@in.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
connector: Delete buggy notification code.
be2net: use eq-id to calculate cev-isr reg offset
Bluetooth: Use the control channel for raw HID reports
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
Bluetooth: Redo checks in IRQ handler for shared IRQ support
Bluetooth: Fix memory leak in L2CAP
Bluetooth: Remove double free of SKB pointer in L2CAP
cdc_ether: Partially revert "usbnet: Set link down initially ..."
be2net: Fix memset() arg ordering.
bonding: bond_open error return value
ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
ixgbe: set the correct DCB bit for pg tx settings
igbvf: fix issue w/ mapped_as_page being left set after unmap
drivers/net: ks8851_mll ethernet network driver
be2net: Bug fix to support newer generation of BE ASIC
starfire: clean up properly if firmware loading fails
mac80211: fix NULL pointer dereference when ftrace is enabled
netfilter: ctnetlink: fix expectation mask dump
ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
ath9k: fix eeprom INI values override for 2GHz-only cards
...
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
hw_breakpoints: Release the bp slot if arch_validate_hwbkpt_settings() fails.
perf: Ignore perf.data.old
perf report: Fix segmentation fault when running with '-g none'
This patch fixes the regression in functionality where the
kernel debugger and the perf API do not nicely share hw
breakpoint reservations.
The kernel debugger cannot use any mutex_lock() calls because it
can start the kernel running from an invalid context.
A mutex free version of the reservation API needed to get
created for the kernel debugger to safely update hw breakpoint
reservations.
The possibility for a breakpoint reservation to be concurrently
processed at the time that kgdb interrupts the system is
improbable. Should this corner case occur the end user is
warned, and the kernel debugger will prohibit updating the
hardware breakpoint reservations.
Any time the kernel debugger reserves a hardware breakpoint it
will be a system wide reservation.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-3-git-send-email-jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For pressure-based multi-touch devices, a direct way to send sensor
intensity data per finger is needed. This patch adds the ABS_MT_PRESSURE
event to the MT protocol.
Requested-by: Yoonyoung Shim <jy0922.shim@samsung.com>
Requested-by: Mika Kuoppala <mika.kuoppala@nokia.com>
Requested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] aic79xx: check for non-NULL scb in ahd_handle_nonpkt_busfree
[SCSI] zfcp: Set hardware timeout as requested by BSG request.
[SCSI] zfcp: Introduce bsg_timeout callback.
[SCSI] scsi_transport_fc: Allow LLD to reset FC BSG timeout
[SCSI] zfcp: add missing compat ptr conversion
[SCSI] zfcp: Fix linebreak in hba trace
[SCSI] zfcp: Issue zfcp_fc_wka_port_put after FC CT BSG request
[SCSI] qla2xxx: Update version number to 8.03.01-k10.
[SCSI] fc-transport: Use packed modifier for fc_bsg_request structure.
[SCSI] qla2xxx: Perform fast mailbox read of flash regardless of size nor address alignment.
[SCSI] qla2xxx: Correct FCP2 recovery handling.
[SCSI] scsi_lib: Fix bug in completion of bidi commands
[SCSI] mptsas: Fix issue with chain pools allocation on katmai
[SCSI] aacraid: fix File System going into read-only mode
[SCSI] lpfc: fix file permissions
It's a simplified 'read_cache_page()' which takes a page allocation
flag, so that different paths can control how aggressive the memory
allocations are that populate a address space.
In particular, the intel GPU object mapping code wants to be able to do
a certain amount of own internal memory management by automatically
shrinking the address space when memory starts getting tight. This
allows it to dynamically use different memory allocation policies on a
per-allocation basis, rather than depend on the (static) address space
gfp policy.
The actual new function is a one-liner, but re-organizing the helper
functions to the point where you can do this with a single line of code
is what most of the patch is all about.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct fw_cdev_add_descriptor.length is in quadlets, not in bytes.
Also remove any doubts about the endianess of descriptor data.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix leak of free lapic date in kvm_arch_vcpu_init()
KVM: x86: Fix probable memory leak of vcpu->arch.mce_banks
KVM: S390: fix potential array overrun in intercept handling
KVM: fix spurious interrupt with irqfd
eventfd - allow atomic read and waitqueue remove
KVM: MMU: bail out pagewalk on kvm_read_guest error
KVM: properly check max PIC pin in irq route setup
KVM: only allow one gsi per fd
KVM: x86: Fix host_mapping_level()
KVM: powerpc: Show timing option only on embedded
KVM: Fix race between APIC TMR and IRR
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (95 commits)
drm/radeon/kms: preface warning printk with driver name
drm/radeon/kms: drop unnecessary printks.
drm: fix regression in fb blank handling
drm/radeon/kms: make hibernate work on IGPs
drm/vmwgfx: Optimize memory footprint for DMA buffers.
drm/ttm: Allow system memory as a busy placement.
drm/ttm: Fix race condition in ttm_bo_delayed_delete (v3, final)
drm/nv50: prevent switching off SOR when in use for DVI-over-DP
drm/nv50: fail auxch transaction if reply count not what we expect
drm/nouveau: fix failure path if userspace specifies no valid memtypes
drm/nouveau: report LVDS as disconnected if lid closed
drm/radeon/kms: fix legacy get_engine/memory clock
drm/radeon/kms/atom: atom parser fixes
drm/radeon/kms: clean up atombios pll code
drm/radeon/kms: clean up pll struct
drm/radeon/kms/atom: fix crtc lock ordering
drm/radeon: r6xx/r7xx possible security issue, system ram access
drm/radeon/kms: r600/r700 don't test ib if ib initialization fails
drm/radeon/kms: Forbid creation of framebuffer with no valid GEM object
drm/radeon/kms: r600 handle irq vector ring overflow
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
virtio_net: Make delayed refill more reliable
sfc: Use fixed-size buffers for MCDI NVRAM requests
sfc: Add workspace for GMAC bug workaround to MCDI MAC_STATS buffer
tcp_probe: avoid modulus operation and wrap fix
qlge: Only free resources if they were allocated
netns xfrm: deal with dst entries in netns
sky2: revert config space change
vlan: fix vlan_skb_recv()
netns xfrm: fix "ip xfrm state|policy count" misreport
sky2: Enable/disable WOL per hardware device
net: Fix IPv6 GSO type checks in Intel ethernet drivers
igb/igbvf: cleanup exception handling in tx_map_adv
MAINTAINERS: Add Intel igbvf maintainer
e1000/e1000e: don't use small hardware rx buffers
fmvj18x_cs: add new id (Panasonic lan & modem card)
be2net: swap only first 2 fields of mcc_wrb
Please add support for Microsoft MN-120 PCMCIA network card
be2net: fix bug in rx page posting
wimax/i2400m: Add support for more i6x50 SKUs
e1000e: enhance frame fragment detection
...
KVM needs a wait to atomically remove themselves from the eventfd ->poll()
wait queue head, in order to handle correctly their IRQfd deassign
operation.
This patch introduces such API, plus a way to read an eventfd from its
context.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
GC is non-existent in netns, so after you hit GC threshold, no new
dst entries will be created until someone triggers cleanup in init_net.
Make xfrm4_dst_ops and xfrm6_dst_ops per-netns.
This is not done in a generic way, because it woule waste
(AF_MAX - 2) * sizeof(struct dst_ops) bytes per-netns.
Reorder GC threshold initialization so it'd be done before registering
XFRM policies.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/~dwmw2/mtd-2.6.33:
mtd: tests: fix read, speed and stress tests on NOR flash
mtd: Really add ARM pismo support
kmsg_dump: Dump on crash_kexec as well
"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
sched: Fix vmark regression on big machines
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
USB: isp1362: better 64bit printf warning fixes
USB: fix usbstorage for 2770:915d delivers no FAT
USB: Fix level of isp1760 Reloading ptd error message
USB: FHCI: avoid NULL pointer dereference
USB: Fix duplicate sysfs problem after device reset.
USB: add speed values for USB 3.0 and wireless controllers
USB: add missing delay during remote wakeup
USB: EHCI & UHCI: fix race between root-hub suspend and port resume
USB: EHCI: fix handling of unusual interrupt intervals
USB: Don't use GFP_KERNEL while we cannot reset a storage device
USB: fix bitmask merge error
usb: serial: fix memory leak in generic driver
USB: serial: fix USB serial fix kfifo_len locking
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
fs/bio.c: fix shadows sparse warning
drbd: The kernel code is now equivalent to out of tree release 8.3.7
drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
drbd: Don't go into StandAlone mode when authentification failes because of network error
drivers/block/drbd/drbd_receiver.c: correct NULL test
cfq-iosched: Respect ioprio_class when preempting
genhd: overlapping variable definition
block: removed unused as_io_context
DM: Fix device mapper topology stacking
block: bdev_stack_limits wrapper
block: Fix discard alignment calculation and printing
block: Correct handling of bottom device misaligment
drbd: check on CONFIG_LBDAF, not LBD
drivers/block/drbd: Correct NULL test
drbd: Silenced an assert that could triggered after changing write ordering method
drbd: Kconfig fix
drbd: Fix for a race between IO and a detach operation [Bugz 262]
drbd: Use drbd_crypto_is_hash() instead of an open coded check
The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SD_PREFER_SIBLING is set at the CPU domain level if power saving isn't
enabled, leading to many cache misses on large machines as we traverse
looking for an idle shared cache to wake to. Change the enabler of
select_idle_sibling() to SD_SHARE_PKG_RESOURCES, and enable same at the
sibling domain level.
Reported-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1262612696.15495.15.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 541cd3ee00 ("phylib: Fix deadlock
on resume") caused TI DaVinci EMAC ethernet driver to oops upon resume:
PM: resume of devices complete after 237.098 msecs
Restarting tasks ... done.
kernel BUG at kernel/workqueue.c:354!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
Backtrace:
[<c002c598>] (__bug+0x0/0x2c) from [<c0052a54>] (queue_delayed_work_on+0x74/0xf8)
[<c00529e0>] (queue_delayed_work_on+0x0/0xf8) from [<c0052b30>] (queue_delayed_work+0x2c/0x30)
The oops pops up because TI DaVinci EMAC driver detaches PHY on
suspend and attaches it back on resume. Attaching makes phylib call
phy_start_machine() that initializes a workqueue. On the other hand,
PHY's resume routine will call phy_start_machine() again, and that
will cause the oops since we just destroyed the already scheduled
workqueue.
This patch fixes the issue by moving workqueue initialization to
phy_device_create().
p.s. We don't see this oops with ucc_geth and gianfar drivers because
they perform a fine-grained suspend, i.e. they just stop the PHYs
without detaching.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the simple fancy sysfs hooks for the aux GPIOs and expose these via
the gpiolib interface so that other drivers can use them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch abstracts out the CNF area code from tmio_mmc which
is not present in all hardware that can use this driver. This
is required so that we can support non-toshiba based hardware.
ASIC3 support by Philipp Zabel
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The constants used to specify ISINK ramp times for WM835x had the
wrong shifts so that the on times applied to the off ramp and vice
versa. The masks for the bitfields are correct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
do_add_mount() should sanitize mnt_flags
CIFS shouldn't make mountpoints shrinkable
mnt_flags fixes in do_remount()
attach_recursive_mnt() needs to hold vfsmount_lock over set_mnt_shared()
may_umount() needs namespace_sem
Fix configfs leak
Fix the -ESTALE handling in do_filp_open()
ecryptfs: Fix refcnt leak on ecryptfs_follow_link() error path
Fix ACC_MODE() for real
Unrot uml mconsole a bit
hppfs: handle ->put_link()
Kill 9p readlink()
fix autofs/afs/etc. magic mountpoint breakage
The 32bit kernel does not add padding bytes in the fc_bsg_request structure
whereas the 64bit kernel adds padding bytes in the fc_bsg_request structure.
Due to this, structure elements gets mismatched with 32bit application and
64bit kernel.To resolve this, used packed modifier to avoid adding padding bytes.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/filters: Add comment for match callbacks
tracing/filters: Fix MATCH_FULL filter matching for PTR_STRING
tracing/filters: Fix MATCH_MIDDLE_ONLY filter matching
lib: Introduce strnstr()
tracing/filters: Fix MATCH_END_ONLY filter matching
tracing/filters: Fix MATCH_FRONT_ONLY filter matching
ftrace: Fix MATCH_END_ONLY function filter
tracing/x86: Derive arch from bits argument in recordmcount.pl
ring-buffer: Add rb_list_head() wrapper around new reader page next field
ring-buffer: Wrap a list.next reference with rb_list_head()
Fix a problem in NOMMU mmap with ramfs whereby a shared mmap can happen
over the end of a truncation. The problem is that
ramfs_nommu_check_mappings() checks that the reduced file size against the
VMA tree, but not the vm_region tree.
The following sequence of events can cause the problem:
fd = open("/tmp/x", O_RDWR|O_TRUNC|O_CREAT, 0600);
ftruncate(fd, 32 * 1024);
a = mmap(NULL, 32 * 1024, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
b = mmap(NULL, 16 * 1024, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
munmap(a, 32 * 1024);
ftruncate(fd, 16 * 1024);
c = mmap(NULL, 32 * 1024, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
Mapping 'a' creates a vm_region covering 32KB of the file. Mapping 'b'
sees that the vm_region from 'a' is covering the region it wants and so
shares it, pinning it in memory.
Mapping 'a' then goes away and the file is truncated to the end of VMA
'b'. However, the region allocated by 'a' is still in effect, and has
_not_ been reduced.
Mapping 'c' is then created, and because there's a vm_region covering the
desired region, get_unmapped_area() is _not_ called to repeat the check,
and the mapping is granted, even though the pages from the latter half of
the mapping have been discarded.
However:
d = mmap(NULL, 16 * 1024, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
Mapping 'd' should work, and should end up sharing the region allocated by
'a'.
To deal with this, we shrink the vm_region struct during the truncation,
lest do_mmap_pgoff() take it as licence to share the full region
automatically without calling the get_unmapped_area() file op again.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_unmapped_area() is unnecessary for NOMMU as no-one calls it.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vm_usage count field in struct vm_region does not need to be atomic as
it's only even modified whilst nommu_region_sem is write locked.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add BUILD_BUG_ON_NOT_POWER_OF_2()
When code relies on a constant being a power of 2:
#define FOO 512 /* must be a power of 2 */
it would be nice to be able to do:
BUILD_BUG_ON(!is_power_of_2(FOO));
However applying an inline function does not result in a compile-time
constant that can be used with BUILD_BUG_ON(), so trying that gives
results in:
error: bit-field '<anonymous>' width not an integer constant
As suggested by akpm, rather than monkeying around with is_power_of_2()
and risking gcc warts about constant expressions, just create a macro
BUILD_BUG_ON_NOT_POWER_OF_2() to encapsulate this common requirement.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: David Dillow <dave@thedillows.org>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On my first try using them I missed that the fifos need to be power of
two, resulting in a runtime bug. Document that requirement everywhere
(and fix one grammar bug)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Walls <awalls@radix.net>
Cc: Vikram Dhillon <dhillonv10@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple inline that checks if kfifo_init() has been executed on a fifo.
This is useful for walking all per CPU fifos, when some of them might not
have been brought up yet.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Walls <awalls@radix.net>
Cc: Vikram Dhillon <dhillonv10@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some upcoming code it's useful to peek into a FIFO without permanentely
removing data. This patch implements a new kfifo_out_peek() to do this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Walls <awalls@radix.net>
Cc: Vikram Dhillon <dhillonv10@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now for kfifo_*_user it's not easily possible to distingush between
a user copy failing and the FIFO not containing enough data. The problem
is that both conditions are multiplexed into the same return code.
Avoid this by moving the "copy length" into a separate output parameter
and only return 0/-EFAULT in the main return value.
I didn't fully adapt the weird "record" variants, those seem
to be unused anyways and were rather messy (should they be just removed?)
I would appreciate some double checking if I did all the conversions
correctly.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Walls <awalls@radix.net>
Cc: Vikram Dhillon <dhillonv10@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pointers to user buffers are currently unsigned char *, which requires
a lot of casting in the caller for any non-char typed buffers. Use void *
instead.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Walls <awalls@radix.net>
Cc: Vikram Dhillon <dhillonv10@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I get a few dozen of these warnings when using
gcc (GCC) 4.4.1 20090725 (Red Hat 4.4.1-2):
In file included from mmotm-2010-0113-1217/init/do_mounts.c:5:
mmotm-2010-0113-1217/include/linux/tty.h: In function 'tty_port_get':
mmotm-2010-0113-1217/include/linux/tty.h:469: warning: '______f' is static but declared in inline function 'tty_port_get' which is not static
so make the function static inline.
[akpm@linux-foundation.org: may as well convert tty_port_users() also]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
