The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two bugs in the error handling:
1: If devm_of_phy_provider_register() fails then there was no cleanup.
2: The error handling called of_node_put(child) improperly leading to
a use after free. We are only holding the reference inside the loop
so the last two gotos after the loop lead to a use after free bug.
Fix this by cleaning up the partial allocations (or partial iterations)
in the loop before doing the goto.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Fixes: 44d30d6228 ("phy: cadence: Add driver for Sierra PHY")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220115115146.GC7552@kili
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The previous commit 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on
the BCM4908") added a second "default" line for ARCH_BCM_4908 above
the original "default" line for ARCH_BRCMSTB. When two "default"
lines are used, only the first is used and this change stopped
the PHY_BRCM_USB option for being enabled for ARCH_BRCMSTB.
The fix is to use one "default line with "||".
Fixes: 4b402fa8e0 ("phy: phy-brcm-usb: support PHY on the BCM4908")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-4-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).
The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char, misc, and other "small" driver
subsystem changes for 5.17-rc1.
Lots of different things are in here for char/misc drivers such as:
- habanalabs driver updates
- mei driver updates
- lkdtm driver updates
- vmw_vmci driver updates
- android binder driver updates
- other small char/misc driver updates
Also smaller driver subsystems have also been updated, including:
- fpga subsystem updates
- iio subsystem updates
- soundwire subsystem updates
- extcon subsystem updates
- gnss subsystem updates
- phy subsystem updates
- coresight subsystem updates
- firmware subsystem updates
- comedi subsystem updates
- mhi subsystem updates
- speakup subsystem updates
- rapidio subsystem updates
- spmi subsystem updates
- virtual driver updates
- counter subsystem updates
Too many individual changes to summarize, the shortlog contains the
full details.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (406 commits)
counter: 104-quad-8: Fix use-after-free by quad8_irq_handler
dt-bindings: mux: Document mux-states property
dt-bindings: ti-serdes-mux: Add defines for J721S2 SoC
counter: remove old and now unused registration API
counter: ti-eqep: Convert to new counter registration
counter: stm32-lptimer-cnt: Convert to new counter registration
counter: stm32-timer-cnt: Convert to new counter registration
counter: microchip-tcb-capture: Convert to new counter registration
counter: ftm-quaddec: Convert to new counter registration
counter: intel-qep: Convert to new counter registration
counter: interrupt-cnt: Convert to new counter registration
counter: 104-quad-8: Convert to new counter registration
counter: Update documentation for new counter registration functions
counter: Provide alternative counter registration functions
counter: stm32-timer-cnt: Convert to counter_priv() wrapper
counter: stm32-lptimer-cnt: Convert to counter_priv() wrapper
counter: ti-eqep: Convert to counter_priv() wrapper
counter: ftm-quaddec: Convert to counter_priv() wrapper
counter: intel-qep: Convert to counter_priv() wrapper
counter: microchip-tcb-capture: Convert to counter_priv() wrapper
...
Vinod writes:
phy-for-5.17
- New support:
- Qualcomm eDP PHY driver
- Qualcomm SM8450 UFS, USB2, USB3, PCIe0 and PCIe1 phy support
- Lan966x ethernet serdes PHY driver
- Support for uniphier NXI & Pro4 SoC
- Qualcomm SM6350 USB2 support
- Amlogic Meson8 HDMI TX PHY driver
- Rockchip rk3568 usb2 support
- Intel Thunder Bay eMMC PHY driver
- Freescale IMX8 PCIe phy driver
- Updates:
- Cadence Sierra driver updates for multilink configurations
- Bcm usb2 updates for Phy reg space
* tag 'phy-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: cadence: Sierra: Add support for derived reference clock output
dt-bindings: phy: cadence-sierra: Add clock ID for derived reference clock
phy: cadence: Sierra: Add PCIe + QSGMII PHY multilink configuration
phy: cadence: Sierra: Add support for PHY multilink configurations
phy: cadence: Sierra: Fix to get correct parent for mux clocks
phy: cadence: Sierra: Update single link PCIe register configuration
phy: cadence: Sierra: Check PIPE mode PHY status to be ready for operation
phy: cadence: Sierra: Check cmn_ready assertion during PHY power on
phy: cadence: Sierra: Add PHY PCS common register configurations
phy: cadence: Sierra: Rename some regmap variables to be in sync with Sierra documentation
phy: cadence: Sierra: Add support to get SSC type from device tree
dt-bindings: phy: cadence-sierra: Add binding to specify SSC mode
dt-bindings: phy: cadence-torrent: Rename SSC macros to use generic names
phy: cadence: Sierra: Prepare driver to add support for multilink configurations
phy: cadence: Sierra: Use of_device_get_match_data() to get driver data
phy: mediatek: Fix missing check in mtk_mipi_tx_probe
phy: uniphier-usb3ss: fix unintended writing zeros to PHY register
phy: phy-mtk-tphy: use new io helpers to access register
phy: phy-mtk-xsphy: use new io helpers to access register
phy: mediatek: add helpers to update bits of registers
...
Sierra has derived differential reference clock output which is sourced
after the spread spectrum generation has been added. Add support to drive
derived reference clock out of serdes. Model this derived clock as a
"clock" so that platforms using this can enable it.
Sierra Main LC VCO PLL divider 1 clock is programmed to output 100MHz
clock output.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-16-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add register sequences for PCIe + QSGMII PHY multilink configuration.
PHY configuration for multi-link operation is done in two steps.
e.g. Consider a case for a 4 lane PHY with PCIe using 2 lanes and QSGMII
other 2 lanes. Sierra PHY has 2 PLLs, viz. PLLLC and PLLLC1. So in this
case, PLLLC is used for PCIe and PLLLC1 is used for QSGMII.
PHY is configured in two steps as described below.
[1] For first step, the register values are selected as
[TYPE_PCIE][TYPE_QSGMII][ssc].
This will configure PHY registers associated for PCIe involving PLLLC
registers and registers for first 2 lanes of PHY.
[2] In second step, the register values are selected as
[TYPE_QSGMII][TYPE_PCIE][ssc].
This will configure PHY registers associated for QSGMII involving
PLLLC1 registers and registers for other 2 lanes of PHY.
This completes the PHY configuration for multilink operation.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-14-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix get_parent() callback to return the correct index of the parent for
PLL_CMNLC1 clock. Add a separate table of register values corresponding
to the parent index for PLL_CMNLC1. Update set_parent() callback
accordingly.
Fixes: 28081b7285 ("phy: cadence: Sierra: Model PLL_CMNLC and PLL_CMNLC1 as clocks (mux clocks)")
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20211223060137.9252-12-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
kernel test robot complains about missing FIELD_PREP, so include
bitfield.h for that
drivers/phy/freescale/phy-fsl-imx8m-pcie.c:41:37: error: implicit declaration of function 'FIELD_PREP' [-Werror=implicit-function-declaration]
drivers/phy/freescale/phy-fsl-imx8m-pcie.c:41:41: error: implicit declaration of function 'FIELD_PREP' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211215060834.921617-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Variable delay is being assigned to zero and the code falls through to
the next case in a switch statement that returns out of the function.
The variable is never read in this scenario and so the assignment is
redundant and can be removed.
Cleans up scan-build static analysis warning:
drivers/phy/rockchip/phy-rockchip-inno-usb2.c:753:3: warning: Value
stored to 'delay' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211211180054.525368-1-colin.i.king@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for PHY_INTERFACE_MODE_5GBASER mode within the Marvell CP110
common PHY driver.
This is currently only supported via SMC calls to TF-A. Legacy support
may be added later, if needed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
