[Why]
Even if YUV420 is available for video mode, YUV444 is still
automatically selected. This poses a problem for compliance tests.
[How]
Add a per-connector debugfs entry "force_yuv420_output" to force
selection of YUV420 mode.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Surface dchub/dpp update would not trigger if a stream update was the
only cause. This change now allows stream flags to trigger this update.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The issue is specific for linux, as on timings such as 8K@60
or 4K@144 DSC should be working in combination with ODM Combine
in order to ensure that we can run those timings. The validation
for those timings was passing, but when pipe split was happening
second pipe wasn't being programmed.
[how]
Rebuild mapped resources if we split stream for ODM.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current configuration 0 is just a placeholder, and final parameters needed.
Also, configuration 1 is expected to emulate ABM 2.1 but is too aggressive.
[How]
Redefine configuration 0 with the finalized parameters, and increase the
contrast gain of configuration 1 so that it properly emulates ABM 2.1.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Secondary viewport dimension/position registers are not programmed,
which can cause issues in some stereo configurations.
[How]
Add register definitions and register programming.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP1.2 LL CTS test failure.
[How]
The failure is caused by not verify stream link is equal
to link, only check stream and link is not null.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Edid Utility wishes to include DSC module from driver instead
of doing it's own logic which will need to be updated every time
someone modifies the driver logic.
[How]
Modify some functions such that we dont need to pass the entire
DC structure as parameter.
-Remove DC inclusion from module.
-Filter out problematic types and inclusions
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Underflow occurs on some display setups(repro'd on 3x4K HDR) on boot,
mode set, and hot-plugs with. Underflow occurs because mem clk
is not set high after disabling pstate switching. This behaviour occurs
because some calculations assumed displays were synchronized.
[How] Add a condition to check if timing sync is disabled so that
synchronized vblank can be set to false.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_destroy should only clean up SW, this is because GPUs may be
removed before driver unload, leading to HW to be unavailable.
[how]
remove GPIO close as part of GPIO destroy, this is unnecessary because
GPIO is not shared, and GPIOs are generally closed after being opened
Add tracking to HW access during destructor to make future issues
easier to pinpoint, and block access to prevent hangs.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New behaviour will track global updates and update any hw that isn't
related to current stream being updated.
This should fix any issues caused by pipe split pipes being taken
by other streams.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to add missing surface address register definitions.
- RGBE+A does not work in a stereo configuration because
surface addresses are no programmed correctly.
[How]
Added the register definitions and surface address programming.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's sometimes useful to have this option when debugging
[how]
Add a config flag. If the flag is not set, use driver default policy.
If the flag is set, use the value from the flag as the starting DSC slice
height.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Driver defaults to 1-tap subsample mode for 4:2:2.
DCE11.2 added 3-tap. The policy is:
DCE8-DCE11 - change to 2-tap, it's better than 1-tap.
DCE11.2+ - use 3-tap
Note that 4:2:0 was added in DCE11.2 and already uses 3-tap always.
Note 2 is that DCE not covered on Linux, only DCN+
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When user mode use i2c over aux through ADL or DDI, the function
dal_ddc_service_query_ddc_data will be called. There are two issues.
1. When read/write length > 16byte, current always return false because
the DEFAULT_AUX_MAX_DATA_SIZE != length.
2. When usermode only need to read data through i2c, driver will write
mot = true at the same address and cause i2c sink confused. Therefore
the following read command will get garbage.
[How]
1. Add function dal_dcc_submit_aux_command to handle length > 16 byte.
2. Check read size and write size when query ddc data.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier patch "Hook up calls to do stereo mux and dig programming..."
doesn't include update for dcn21.
[How]
Align dcn21 gpio settings with updated stereo control interface.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With stutter mode enabled, NMI prints frequently.
Disable stutter for the moment because NMI warning storm, and will
enable it back till the issue is addressed
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kbuild provides per-file compiler flag addition/removal:
CFLAGS_<basetarget>.o
CFLAGS_REMOVE_<basetarget>.o
AFLAGS_<basetarget>.o
AFLAGS_REMOVE_<basetarget>.o
CPPFLAGS_<basetarget>.lds
HOSTCFLAGS_<basetarget>.o
HOSTCXXFLAGS_<basetarget>.o
The <basetarget> is the filename of the target with its directory and
suffix stripped.
This syntax comes into a trouble when two files with the same basename
appear in one Makefile, for example:
obj-y += foo.o
obj-y += dir/foo.o
CFLAGS_foo.o := <some-flags>
Here, the <some-flags> applies to both foo.o and dir/foo.o
The real world problem is:
scripts/kconfig/util.c
scripts/kconfig/lxdialog/util.c
Both files are compiled into scripts/kconfig/mconf, but only the
latter should be given with the ncurses flags.
It is more sensible to use the relative path to the Makefile, like this:
obj-y += foo.o
CFLAGS_foo.o := <some-flags>
obj-y += dir/foo.o
CFLAGS_dir/foo.o := <other-flags>
At first, I attempted to replace $(basetarget) with $*. The $* variable
is replaced with the stem ('%') part in a pattern rule. This works with
most of cases, but does not for explicit rules.
For example, arch/ia64/lib/Makefile reuses rule_as_o_S in its own
explicit rules, so $* will be empty, resulting in ignoring the per-file
AFLAGS.
I introduced a new variable, target-stem, which can be used also from
explicit rules.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Zyngier <maz@kernel.org>
