Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't have any notion of a tagging cache anymore, and haven't
for a long time. Kill off the unused enums.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Modified by me to also check at driver tag allocation time if the
original request was reserved, so we can be sure to allocate a
properly reserved tag at that point in time, too.
Signed-off-by: Jens Axboe <axboe@fb.com>
These are very tied to the blk-mq tag implementation, so exposing them
to sysfs isn't a great idea. Move the debugging information to debugfs
and add basic entries for the number of tags and the number of reserved
tags to sysfs.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add support for growing the tags associated with a hardware queue, for
the scheduler tags. Currently we only support resizing within the
limits of the original depth, change that so we can grow it as well by
allocating and replacing the existing scheduler tag set.
This is similar to how we could increase the software queue depth with
the legacy IO stack and schedulers.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
This is in preparation for having two sets of tags available. For
that we need a static index, and a dynamically assignable one.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
This is in preparation for having another tag set available. Cleanup
the parameters, and allow passing in of tags for blk_mq_put_tag().
Signed-off-by: Jens Axboe <axboe@fb.com>
[hch: even more cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Pull blk-mq irq/cpu mapping updates from Jens Axboe:
"This is the block-irq topic branch for 4.9-rc. It's mostly from
Christoph, and it allows drivers to specify their own mappings, and
more importantly, to share the blk-mq mappings with the IRQ affinity
mappings. It's a good step towards making this work better out of the
box"
* 'for-4.9/block-irq' of git://git.kernel.dk/linux-block:
blk_mq: linux/blk-mq.h does not include all the headers it depends on
blk-mq: kill unused blk_mq_create_mq_map()
blk-mq: get rid of the cpumask in struct blk_mq_tags
nvme: remove the post_scan callout
nvme: switch to use pci_alloc_irq_vectors
blk-mq: provide a default queue mapping for PCI device
blk-mq: allow the driver to pass in a queue mapping
blk-mq: remove ->map_queue
blk-mq: only allocate a single mq_map per tag_set
blk-mq: don't redistribute hardware queues on a CPU hotplug event
In order to get good cache behavior from a sbitmap, we want each CPU to
stick to its own cacheline(s) as much as possible. This might happen
naturally as the bitmap gets filled up and the alloc_hint values spread
out, but we really want this behavior from the start. blk-mq apparently
intended to do this, but the code to do this was never wired up. Get rid
of the dead code and make it part of the sbitmap library.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Again, there's no point in passing this in every time. Make it part of
struct sbitmap_queue and clean up the API.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allocating your own per-cpu allocation hint separately makes for an
awkward API. Instead, allocate the per-cpu hint as part of the struct
sbitmap_queue. There's no point for a struct sbitmap_queue without the
cache, but you can still use a bare struct sbitmap.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is a generally useful data structure, so make it available to
anyone else who might want to use it. It's also a nice cleanup
separating the allocation logic from the rest of the tag handling logic.
The code is behind a new Kconfig option, CONFIG_SBITMAP, which is only
selected by CONFIG_BLOCK for now.
This should be a complete noop functionality-wise.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Unused now that NVMe sets up irq affinity before calling into blk-mq.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
And replace the blk_mq_tag_busy_iter with it - the driver use has been
replaced with a new helper a while ago, and internal to the block we
only need the new version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Storage controllers may expose multiple block devices that share hardware
resources managed by blk-mq. This patch enhances the shared tags so a
low-level driver can access the shared resources not tied to the unshared
h/w contexts. This way the LLD can dynamically add and delete disks and
request queues without having to track all the request_queue hctx's to
iterate outstanding tags.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is the blk-mq part to support tag allocation policy. The default
allocation policy isn't changed (though it's not a strict FIFO). The new
policy is round-robin for libata. But it's a try-best implementation. If
multiple tasks are competing, the tags returned will be mixed (which is
unavoidable even with !mq, as requests from different tasks can be
mixed in queue)
Cc: Jens Axboe <axboe@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If it's dying, we can't expect new request to complete and come
in an wake up other tasks waiting for requests. So after we
have marked it as dying, wake up everybody currently waiting
for a request. Once they wake, they will retry their allocation
and fail appropriately due to the state of the queue.
Tested-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix racy updates of shared blk_mq_bitmap_tags::wake_index
and blk_mq_hw_ctx::wake_index fields.
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_put_ctx() has to be called before io_schedule() in
bt_get().
This patch fixes the problem by taking similar approach from
percpu_ida allocation for the situation.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The current logic for blocking tag allocation is rather confusing, as we
first allocated and then free again a tag in blk_mq_wait_for_tags, just
to attempt a non-blocking allocation and then repeat if someone else
managed to grab the tag before us.
Instead change blk_mq_alloc_request_pinned to simply do a blocking tag
allocation itself and use the request we get back from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Export the blk-mq in-flight tag iterator for driver consumption.
This is particularly useful in exception paths or SRSI where
in-flight IOs need to be cancelled and/or reissued. The NVMe driver
conversion will use this.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
For request_fn based devices, the block layer exports a 'nr_requests'
file through sysfs to allow adjusting of queue depth on the fly.
Currently this returns -EINVAL for blk-mq, since it's not wired up.
Wire this up for blk-mq, so that it now also always dynamic
adjustments of the allowed queue depth for any given block device
managed by blk-mq.
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds support for active queue tracking, meaning that the
blk-mq tagging maintains a count of active users of a tag set.
This allows us to maintain a notion of fairness between users,
so that we can distribute the tag depth evenly without starving
some users while allowing others to try unfair deep queues.
If sharing of a tag set is detected, each hardware queue will
track the depth of its own queue. And if this exceeds the total
depth divided by the number of active queues, the user is actively
throttled down.
The active queue count is done lazily to avoid bouncing that data
between submitter and completer. Each hardware queue gets marked
active when it allocates its first tag, and gets marked inactive
when 1) the last tag is cleared, and 2) the queue timeout grace
period has passed.
Signed-off-by: Jens Axboe <axboe@fb.com>
For best performance, spreading tags over multiple cachelines
makes the tagging more efficient on multicore systems. But since
we have 8 * sizeof(unsigned long) tags per cacheline, we don't
always get a nice spread.
Attempt to spread the tags over at least 4 cachelines, using fewer
number of bits per unsigned long if we have to. This improves
tagging performance in setups with 32-128 tags. For higher depths,
the spread is the same as before (BITS_PER_LONG tags per cacheline).
Signed-off-by: Jens Axboe <axboe@fb.com>
blk-mq currently uses percpu_ida for tag allocation. But that only
works well if the ratio between tag space and number of CPUs is
sufficiently high. For most devices and systems, that is not the
case. The end result if that we either only utilize the tag space
partially, or we end up attempting to fully exhaust it and run
into lots of lock contention with stealing between CPUs. This is
not optimal.
This new tagging scheme is a hybrid bitmap allocator. It uses
two tricks to both be SMP friendly and allow full exhaustion
of the space:
1) We cache the last allocated (or freed) tag on a per blk-mq
software context basis. This allows us to limit the space
we have to search. The key element here is not caching it
in the shared tag structure, otherwise we end up dirtying
more shared cache lines on each allocate/free operation.
2) The tag space is split into cache line sized groups, and
each context will start off randomly in that space. Even up
to full utilization of the space, this divides the tag users
efficiently into cache line groups, avoiding dirtying the same
one both between allocators and between allocator and freeer.
This scheme shows drastically better behaviour, both on small
tag spaces but on large ones as well. It has been tested extensively
to show better performance for all the cases blk-mq cares about.
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_wait_for_tags() is only able to wait for "normal" tags,
not reserved tags. Pass in which one we should attempt to get
a tag for, so that waiting for reserved tags will work.
Reserved tags are used for internal commands, which are usually
serialized. Hence no waiting generally takes place, but we should
ensure that it actually works if users need that functionality.
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a new blk_mq_tag_set structure that gets set up before we initialize
the queue. A single blk_mq_tag_set structure can be shared by multiple
queues.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Modular export of blk_mq_{alloc,free}_tagset added by me.
Signed-off-by: Jens Axboe <axboe@fb.com>
Linux currently has two models for block devices:
- The classic request_fn based approach, where drivers use struct
request units for IO. The block layer provides various helper
functionalities to let drivers share code, things like tag
management, timeout handling, queueing, etc.
- The "stacked" approach, where a driver squeezes in between the
block layer and IO submitter. Since this bypasses the IO stack,
driver generally have to manage everything themselves.
With drivers being written for new high IOPS devices, the classic
request_fn based driver doesn't work well enough. The design dates
back to when both SMP and high IOPS was rare. It has problems with
scaling to bigger machines, and runs into scaling issues even on
smaller machines when you have IOPS in the hundreds of thousands
per device.
The stacked approach is then most often selected as the model
for the driver. But this means that everybody has to re-invent
everything, and along with that we get all the problems again
that the shared approach solved.
This commit introduces blk-mq, block multi queue support. The
design is centered around per-cpu queues for queueing IO, which
then funnel down into x number of hardware submission queues.
We might have a 1:1 mapping between the two, or it might be
an N:M mapping. That all depends on what the hardware supports.
blk-mq provides various helper functions, which include:
- Scalable support for request tagging. Most devices need to
be able to uniquely identify a request both in the driver and
to the hardware. The tagging uses per-cpu caches for freed
tags, to enable cache hot reuse.
- Timeout handling without tracking request on a per-device
basis. Basically the driver should be able to get a notification,
if a request happens to fail.
- Optional support for non 1:1 mappings between issue and
submission queues. blk-mq can redirect IO completions to the
desired location.
- Support for per-request payloads. Drivers almost always need
to associate a request structure with some driver private
command structure. Drivers can tell blk-mq this at init time,
and then any request handed to the driver will have the
required size of memory associated with it.
- Support for merging of IO, and plugging. The stacked model
gets neither of these. Even for high IOPS devices, merging
sequential IO reduces per-command overhead and thus
increases bandwidth.
For now, this is provided as a potential 3rd queueing model, with
the hope being that, as it matures, it can replace both the classic
and stacked model. That would get us back to having just 1 real
model for block devices, leaving the stacked approach to dm/md
devices (as it was originally intended).
Contributions in this patch from the following people:
Shaohua Li <shli@fusionio.com>
Alexander Gordeev <agordeev@redhat.com>
Christoph Hellwig <hch@infradead.org>
Mike Christie <michaelc@cs.wisc.edu>
Matias Bjorling <m@bjorling.me>
Jeff Moyer <jmoyer@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
