It looks pointless to pass max_vol to s5m8767_convert_voltage_to_sel().
Compare selected voltage to desc->max is enough to ensure selected voltage
is in supported range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The function sec_reg_read invokes regmap_read which expects unsigned int *
as the destination address. The existing driver is passing address of local
variable "val" which is u8. This causes the stack corruption and following
dump is observed during probe.
Hence change "val" from u8 to unsigned int.
Unable to handle kernel paging request at virtual address 02410020
pgd = c0004000
[02410020] *pgd=00000000
Internal error: Oops: 80000005 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.6.0-00696-g98a28b18-dirty #27)
PC is at 0x2410020
LR is at _regulator_get_voltage+0x3c/0x70
pc : [<02410020>] lr : [<c02395d4>] psr: 20000013
sp : cf839b68 ip : 00000000 fp : cf92d410
r10: 0000cfd0 r9 : c06d9878 r8 : 0000f0a0
r7 : cf839b70 r6 : cf92d400 r5 : 00000011 r4 : cf000000
r3 : 02410020 r2 : 00000000 r1 : 00000048 r0 : cf000000
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
...........................
.................................
[<c02395d4>] (_regulator_get_voltage+0x3c/0x70) from [<c023ad80>] (print_constraints+0x50/0x36c)
[<c023ad80>] (print_constraints+0x50/0x36c) from [<c023e504>] (set_machine_constraints+0xe8/0x2b0)
[<c023e504>] (set_machine_constraints+0xe8/0x2b0) from [<c023e9c8>] (regulator_register+0x2fc/0x604)
[<c023e9c8>] (regulator_register+0x2fc/0x604) from [<c049d628>] (s5m8767_pmic_probe+0x688/0x718)
[<c049d628>] (s5m8767_pmic_probe+0x688/0x718) from [<c029915c>] (platform_drv_probe+0x18/0x1c)
[<c029915c>] (platform_drv_probe+0x18/0x1c) from [<c0297dd0>] (really_probe+0x68/0x1f4)
[<c0297dd0>] (really_probe+0x68/0x1f4) from [<c0298070>] (driver_probe_device+0x30/0x48)
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies the DVS register read function to select correct DVS1
register. This change is required because the GPIO select pin is 000 in
unintialized state and hence selects the DVS1 register.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to a merge conflict we are getting this:
drivers/regulator/s5m8767.c: In function ‘s5m8767_pmic_probe’:
drivers/regulator/s5m8767.c:575:2: error: implicit declaration of function
‘s5m_reg_write’ [-Werror=implicit-function-declaration]
This is fixed by fully converting this driver to the new s5m API.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac96: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
As Prefix of Samsung pmic changed from s5m to s2m,
To make common mfd driver for s2m and s5m series,
This patch rename header of Samsung mfd and modify mfd driver.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previous naming rule of samsung pmic start with s5m prefix.
But It is changed by s2m.
To cover various samsung s2m and s5m series,
This patch modify function and variable name for common usage.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, Samsung PMIC naming rule start with prefix of s5m.
But Naming rule is changed.
From now on, Prefix will be changed to s2m.
So, To support pmic series of s5m and s2m, change mfd file and directory name.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert to devm_gpio_request to save a few error handling code.
This patch properly handle the gpio_request failure, we should return error
when gpio_request fails rather than just show warning.
I think one of the reason we got -EBUSY is because current code does not free
gpios in s5m8767_pmic_remove(). So it got -EBUSY when reload the module.
Yest another reason is in current code if gpio_request() returns error,
the rest of the code still calls gpio_direction_output to config buck_gpios
and buck_ds gpios. This looks wrong to me.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In current code, .list_voltage and .set_voltage_sel callbacks for BUCK7 and
BUCK8 return -EINVAL.
This patch adds s5m8767_buck78_ops for BUCK7 and BUCK8 which does not set
.list_voltage, .get_voltage_sel and .set_voltage_sel. ( This has the same
effect of returning -EINVAL in the callbacks)
Then for all the users of s5m8767_list_voltage, we don't need to worry about
the case reg_voltage_map[reg_id] is NULL.
So we can convert s5m8767_list_voltage to regulator_list_voltage_linear.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As s5m8767a is revisioned, ramp_delay register is changed.
5mV/uS, 10mV/uS, 25mV/uS, 50mV/uS, 100mV/uS ramp delay can be selected.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into regulator-drivers
Linux 3.5-rc4 contains patches which conflict with some of the
development work.
The S5M8767A can't know status of ap reset.
So, After AP watchdog reset, AP can't boot normally.
Problem can be happened like below condition.
- AP Bootable lowest voltage(vdd_arm): 0.9v
- AP DVFS voltage table: 0.8v, 0.9v, 1.0v
- During AP works on lowest voltage(0.8V), watchdog reset is asserted
- AP can't boot, because vdd arm is still 0.8v
Solution
- Basic concept:
After ap watchdog reset, GPIO configuration is changed by default value
- S5M8767A has function of voltage control with gpio (8 levels with 3 gpios)
- Set bootable voltage on level 0 -> can work with default gpio configuration
- In the probing, Change voltage control level from level 0 to level 1
- Execute normal dvfs operation on level 1
- After watchdog reset, ap gpio is set by default value
- PMIC operation mode is changed by ap reset (level1 -> level0)
- Regardless of previous vdd_arm voltage, AP always can be booted.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If ramp_delay is 0, delay value can be divided by zero.
This patch can fix the problem.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To apply delay time for voltage change,
replace s5m8767_set_voltage with s5m8767_set_voltage_sel.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As s5m8767a is revisioned, remove unnecessary buck 2,3,4 initialization routine.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All the drivers that need delay for the regulator voltage output voltage to
stabilize after being enabled or after being set to a new value has been
converted to implement enable_time and set_voltage_time_sel callbacks.
Then regulator core will take care of the necessary delay.
For the drivers that don't need the delay, don't need to include linux/delay.h.
This patch removes the unneeded include of linux/delay.h in regulator drivers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Integer division may truncate the result.
Use DIV_ROUND_UP to ensure new voltage setting falls within specified range.
Also properly handle the case min_vol < desc->min to ensure we don't return
negative value for selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All the callback function implementation are the same for both LDOs and BUCKs.
Merge them to one s5m8767_ops.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
s5m8767_set_voltage not only implement set_voltage callbacks for LDOs,
but also for BUCKs when s5m8767->buck_gpioindex is not set.
s5m8767_set_voltage_buck actually only for buck[2|3|4] when
s5m8767->buck_gpioindex is set.
Conditionally calling s5m8767_set_voltage in s5m8767_set_voltage_buck makes
the code hard to read.
I think merging s5m8767_set_voltage_buck and s5m8767_set_voltage actually
simplifies things. It's easy to use buck234_vol pointer to differentiate if
we need to control voltage for buck[2|3|4] by DVS GPIOs.
This patch reworks s5m8767_set_voltage to support both LDOx and BUCKx in all
cases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than adding new arguments to regulator_register() every time we
want to add a new bit of dynamic information at runtime change the function
to take these via a struct. By doing this we avoid needing to do further
changes like the recent addition of device tree support which required each
regulator driver to be updated to take an additional parameter.
The regulator_desc which should (mostly) be static data is still passed
separately as most drivers are able to configure this statically at build
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
S5M8767A has 4 operation mode for BUCK/LDOs.
This patch can handle opmode for s5m8767a.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code does not really update the register with new value, fix it.
I rename the variable i to sel for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check s5m8767->buck[2|3|4]_gpiodvs status in s5m8767_get_voltage_register
and return correct register accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we need to ensure only one of the buck[2|3|4]_gpiodvs can be specificed,
check them earlier.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This function finds the smallest voltage that falls within the specified range,
and then returns the selector. This rename makes the intention more clear.
Also remove unneeded local variables min_vol and max_vol in s5m8767_set_voltage
and s5m8767_set_voltage_buck.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the s5m8767_set_voltage_time_sel function, divisor unit is wrong.
ramp_delay is usec unit. So 1000 should be multiplied.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch includes below fixes:
1. The mask variable is not used at all here, remove it.
2. We already have the new_sel and old_sel, simply returns the delay by:
DIV_ROUND_UP(desc->step * (new_sel - old_sel), s5m8767->ramp_delay);
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Calling s5m8767_get_reg_id() is exactly the same as calling rdev_get_id().
It is pointless to add s5m8767_get_reg_id() function.
Use rdev_get_id() directly and remove s5m8767_get_reg_id() function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MODULE_DEVICE_TABLE will setup the modalias, thus adding
a MODULE_ALIAS for an entry already in s5m8767_pmic_id is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
S5M8767A is a cost-effective PMIC which is designed for mobile applications.
It includes high efficient 9 Buck converters, 28 LDOs.
Especially, S5M8767A is optimized for Multi-core SOCs.
And during DVFS operation, S5M8767A output stable voltage.
This patch implement regulator driver for S5M8767A.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
