VF's attempt to delete vlan 0 when a port vlan is configured is harmless
in this case pf driver just does nothing. If vf will try to remove
other vlans when a port vlan is configured it will still produce error
as before.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TX MDD events reported on the PF are the result of the
PF misconfiguring a descriptor and not because of "bad actions"
by anything else. No need to reset now because if it
results in a Tx hang, the Tx hang check will take care of it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the driver behavior when detecting a VF MDD event.
It now disables the VF after one event, which indicates a hw detected
problem in the VF. Before this change, the PF would allow a couple of
events before doing the reset.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethernet flow control:
The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).
Duplex:
There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).
But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.
As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.
So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).
Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
or less clear (needs to be added by the PHY), what should the MAC
driver do about the Tx delays? Is it an implicit wild card for the
MAC to apply delays in the Tx direction if it can? What if those were
already added as serpentine PCB traces, how could that be made more
obvious through DT bindings so that the MAC doesn't attempt to add
them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
fixed (a purely software entity that obviously cannot add clock
skew), what is the meaning of the above property?
So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.
The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.
For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.
Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While moving the chunk of code during 739de9a156
("net: macb: Reorganize macb_mii bringup"), the declaration of
struct phy_device declaration was kept. It's not useful in this
function as we alrady have a phydev pointer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Out of bounds access in xfrm IPSEC policy unlink, from Yue Haibing.
2) Missing length check for esp4 UDP encap, from Sabrina Dubroca.
3) Fix byte order of RX STBC access in mac80211, from Johannes Berg.
4) Inifnite loop in bpftool map create, from Alban Crequy.
5) Register mark fix in ebpf verifier after pkt/null checks, from Paul
Chaignon.
6) Properly use rcu_dereference_sk_user_data in L2TP code, from Eric
Dumazet.
7) Buffer overrun in marvell phy driver, from Andrew Lunn.
8) Several crash and statistics handling fixes to bnxt_en driver, from
Michael Chan and Vasundhara Volam.
9) Several fixes to the TLS layer from Jakub Kicinski (copying negative
amounts of data in reencrypt, reencrypt frag copying, blind nskb->sk
NULL deref, etc).
10) Several UDP GRO fixes, from Paolo Abeni and Eric Dumazet.
11) PID/UID checks on ipv6 flow labels are inverted, from Willem de
Bruijn.
12) Use after free in l2tp, from Eric Dumazet.
13) IPV6 route destroy races, also from Eric Dumazet.
14) SCTP state machine can erroneously run recursively, fix from Xin
Long.
15) Adjust AF_PACKET msg_name length checks, add padding bytes if
necessary. From Willem de Bruijn.
16) Preserve skb_iif, so that forwarded packets have consistent values
even if fragmentation is involved. From Shmulik Ladkani.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
udp: fix GRO packet of death
ipv6: A few fixes on dereferencing rt->from
rds: ib: force endiannes annotation
selftests: fib_rule_tests: print the result and return 1 if any tests failed
ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
net/tls: avoid NULL pointer deref on nskb->sk in fallback
selftests: fib_rule_tests: Fix icmp proto with ipv6
packet: validate msg_namelen in send directly
packet: in recvmsg msg_name return at least sizeof sockaddr_ll
sctp: avoid running the sctp state machine recursively
stmmac: pci: Fix typo in IOT2000 comment
Documentation: fix netdev-FAQ.rst markup warning
ipv6: fix races in ip6_dst_destroy()
l2ip: fix possible use-after-free
appletalk: Set error code if register_snap_client failed
net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
rxrpc: Fix net namespace cleanup
ipv6/flowlabel: wait rcu grace period before put_pid()
vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach
tcp: add sanity tests in tcp_add_backlog()
...
Clang warns about the definitions of these macros (full warnings trimmed
for brevity):
drivers/net/wireless/realtek/rtw88/main.c:524:15: warning: signed shift
result (0x3FF00000000) requires 43 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
ra_mask &= RA_MASK_VHT_RATES | RA_MASK_OFDM_IN_VHT;
^~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:527:15: warning: signed shift
result (0xFF0000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
ra_mask &= RA_MASK_HT_RATES | RA_MASK_OFDM_IN_HT_5G;
^~~~~~~~~~~~~~~~
Given that these are all used with ra_mask, which is of type u64, we can
just declare the macros to be ULL as well.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/467
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘rtw_get_channel_group’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:907:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:908:2: note: here
case 1:
^~~~
In file included from ./include/linux/bcd.h:5,
from drivers/net/wireless/realtek/rtw88/phy.c:5:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘phy_get_2g_tx_power_index’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:1021:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:1022:2: note: here
case RTW_CHANNEL_WIDTH_20:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the shift of an integer value more than 32 bits can
occur when nss is more than 32. Fix this by making the integer
constants unsigned long longs before shifting and bit-wise or'ing
with the u64 ra_mask to avoid the undefined shift behaviour.
Addresses-Coverity: ("Bad shift operation")
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: d84aec4215 ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err makes more sense than dev_info when this call fails.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the link event flow works, but can be much better.
Refactor the link event flow to make it cleaner and more clear
on what is going on.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY type ICE_PHY_TYPE_LOW_25G_AUI_C2C is missing from
ice_get_settings_link_up() which is causing a warning
message for unrecognized PHY. Add the PHY type to
correctly set the settings and avoid the warning message.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Every time we want to re-enable interrupts and/or write to a register
that requires an interrupt vector's hardware index we do the following:
vsi->hw_base_vector + q_vector->v_idx
This is a wasteful operation, especially in the hot path. Fix this by
adding a u16 reg_idx member to the ice_q_vector structure and make the
necessary changes to make this work.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Runtime change of PFINT_OICR_ENA register is unnecessary.
The handlers should always clear the atomic bit for each
task as they start, because it will make sure that any late
interrupt will either 1) re-set the bit, or 2) be handled
directly in the "already running" task handler.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issue with non trusted VFs being able to add more than
permitted number of VLANs by adding a check in ice_vc_process_vlan_msg.
Also don't return an error in this case as the VF does not need to know
that it is not trusted.
Also rework ice_vsi_kill_vlan to use the right types.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_vsi_ctrl_rx_rings() we are unnecessarily waiting for
QRX_CTRL_QENA_REQ and QRX_CTRL_QENA_STAT to be the same value prior to
disabling each Rx queue. There is no reason to do this so remove
this wait loop as we already have a wait loop after disabling/enabling
the Rx queue through the QRX_CTRL register to make sure it gets
successfully disabled/enabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver allows rx-usecs-high values to be set,
but when querying the device for rx-usecs-high the value
does not stick. This is because it was not yet implemented.
Add code to allow the user to change rx-usecs-high and
use this to set the q_vector's intrl value.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to set 52 byte RSS hash key.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many places in the code where we do the following:
for (i = 0; i < vsi->num_q_vectors; i++)
Instead use the macro mentioned in the commit title:
ice_for_each_q_vector(vsi, i)
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When stopping Tx rings, we use 'i' as an ring array index for looking up
whether the ice_ring exists and have assigned a q_vector. This checks
rings only within a given TC and we need to go through every ring in
VSI. Use 'q_idx' instead.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce scope of the variable 'err' to inside the for loop instead
of using it as a second looping conditional. Also while here,
improve the debug message if we fail to configure a Rx queue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis points out the default case in the switch statement in
ice_get_itr_intrl_gran() is an infeasible condition causing the default
case statement to be unreachable. Remove it and since the function no
longer returns anything but success, change it to just return void and
update the only call to it accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If there is no queue to disable, return appropriate configuration error
earlier without acquiring the lock.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a framework to store queue specific information
in VSI queue contexts. Currently VSI queue context (represented by
struct ice_q_ctx) only has q_handle as a member. In future patches,
this structure will be updated to hold queue specific information.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.
+--------------------------------------+--------------------------------+
| cpu-0 | cpu-1 |
| -------- | -------- |
| mlx5_ib_remove | mlx5_eswitch_disable_sriov |
| mlx5_ib_unregister_vport_reps | esw_offloads_cleanup |
| mlx5_eswitch_unregister_vport_reps | esw_offloads_unload_all_reps |
| __unload_reps_all_vport | __unload_reps_all_vport |
+--------------------------------------+--------------------------------+
These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.
To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.
Since the state is changing to atomic type, all other read/write should
be atomic action as well.
Fixes: f121e0ea95 (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The check of legal vport is to ensure the vport number falls between
0 and total number of vports. Along with the introduction of uplink
rep, enabled vports are not consecutive any more.
Therefore, rely on the eswitch vport getter function to check if it's
a valid vport.
As the getter function relies on eswitch, add the check of vport
group manager and validation the presence of eswitch structure.
Remove the redundant check in the function calls.
Since the vport array will be allocated once eswitch is initialized
and will be kept alive if eswitch presents, no need to protect it with
the state lock.
Fixes: 5ae5162066 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some functions issue vport commands and access vport array using
vport_index/vport_num interchangeably which is OK for VFs vports.
However, this creates potential bug if those vports are not VFs
(E.g, uplink, sf) where their vport_index don't equal to vport_num.
Prepare code to access mlx5_vport structure using a getter function.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Several functions need to access mlx5_vport and vport_num.
When these functions are called, caller already has mlx5_vport*
available.
Hence pass such mlx5_vport pointer.
This is preparation patch to add error checks to
mlx5_eswitch_get_vport() and to return error status.
By doing so, reduce places where error check of mlx5_eswitch_get_vport()
can be avoided.
While doing such change, mlx5_eswitch_query_vport_drop_stats() gets
corrected to work on vport, instead of vport_idx.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently mlx5_esw_for_each_vf_vport iterates over mlx5_vport entries in
eswitch.c
Same macro in eswitch_offloads.c iterates over vport number in
eswitch_offloads.c
Instead of duplicate macro names, to avoid confusion and to reuse the
same macro in both files, move it to eswitch.h.
To iterate over vport numbers where there is no need to iterate over
mlx5_vport, but only a vport number is needed, rename those macros in
eswitch_offloads.c to mlx5_esw_for_each_vf_num_vport*.
While at it, keep all vport and vport rep iterators together.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_query_nic_vport_vlans() is not used anymore. Hence remove it.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CFLAGS_tracepoint.o specifies CFLAGS for compiling tracepoint.c but
it does not exist under drivers/net/ethernet/mellanox/mlx5/core/.
CFLAGS_tracepoint.o is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The same code that returns XDP frames and releases pages is used both in
mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs. Create a function that
cleans up an MPWQE.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the support to read additional EEPROM information from high pages.
Information for modules such as SFF-8436 and SFF-8636:
1) Application select table
2) User writable EEPROM
3) Thresholds and alarms
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With unlocked TC it is possible to have spurious deletes and inserts of
same filter. TC layer needs drivers to always return error when flow
insertion failed in order to correctly calculate "in_hw_count" for each
filter. Fix mlx5e_configure_flower() to return -EEXIST when TC tries to
insert a filter that is already provisioned to the driver.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets are
tagged with VLAN ID 0x000 (priority tag) and pop/push actions are
replaced by VLAN re-write actions (which are supported by the HW).
Replace TC VLAN pop action with a VLAN priority tag header rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. As a workaround, untagged packets are tagged with
VID 0x000 allowing pop/push actions to be exchanged with VLAN rewrite
actions.
Use the ingress ACL table, preceding the FDB, to push VLAN 0x000 ID tag
for untagged packets and the egress ACL table, succeeding the FDB, to
pop VLAN 0x000 ID tag.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Hardware requires that all TIRs that steer traffic to the same RQ
should share identical tunneled_offload_en value.
For that, the tunneled_offload_en bit should be set/unset (according to
the HW capability) for all TIRs', not only the ones dedicated for
tunneled (inner) traffic.
Fixes: 1b223dd391 ("net/mlx5e: Fix checksum handling for non-stripped vlan packets")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Many TIR context settings are common to different TIR types,
take them into a common function.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This commit introduces support for the "Drop" action in classification
offload. This corresponds to the "-1" action with ethtool -N.
This is achieved using the color marking actions available in the C2
engine, which associate a color to a packet. These colors can be either
Green, Yellow or Red, Red meaning that the packet should be dropped.
Green and Yellow colors are interpreted by the Policer, which isn't
supported yet.
This method of dropping using the Classifier is different than the
already existing early-drop features, such as VLAN filtering and MAC
UC/MC filtering, which are performed during the Parsing step, and
therefore take precedence over classification actions.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces basic classification offloading support for the
PPv2 controller.
The PPv2 classifier has many classification engines, for now we only use
the C2 TCAM match engine.
This engine allows to perform ternary lookups on 64 bits keys (called
Header Extracted Key), that are built by extracting fields from the packet
header and concatenating them. At most 4 fields can be extracted for a
single lookup.
This basic implementation allows to build the HEK from the following
fields :
- L4 source and destination ports (for UDP and TCP)
More fields are to be added in the future.
Classification flows are added through the ethtool interface, using the
newly introduced flow_rule infrastructure as an internal rule
representation, allowing to more easily implement tc flower rules if
need be.
The internal design for now allocates one range of 4 rules per port
due to the internal design of the flow table, which uses 22 sub-flows.
When inserting a classification rule, the rule is created in every
relevant sub-flow.
This low rule-count is a very simple design which reaches quickly the
limitations of the flow table ordering, but guarantees that the rule
ordering will always be respected.
This commit only introduces support for the "steer to rxq" action.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of today, the classification code is used only for RSS. We split the
incoming traffic into multiple flows, that correspond to the ethtool
flow_type parameter.
We don't want to use the ethtool flow definitions such as TCP_V4_FLOW,
for several reason :
- We want to decorrelate the driver code from ethtool as much as
possible, so that we can easily use other interfaces such as tc flower,
- We want the flow_type to be a bitfield, so that we can match flows
embedded into each other, such as TCP4 which is a subset of IP4.
This commit does the conversion to the newer type.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch removing extra whitespaces when writing the flow_table
entries
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As soon as TAILDESCR_PTR is written, DMA transfers might start.
Let's ensure we are ready to receive DMA IRQ's before doing that.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows custom setup of IRQ coalescing for platforms using legacy
platform_device. The irq timeout and count parameters can be used for
tuning cpu load vs. latency.
I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as
unused in the documentation I have available. It does not make any
difference in the hardware I have available, so it is left in to not risk
breaking other platforms where it might be used.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use usleep_range() to avoid problems with msleep() actually sleeping
much longer than expected.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are actually using a BD for both the skb and each frag contained in
it, the oldest TX BD would be overwritten when there was exactly one BD
less than needed.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap the actual buffer length, not the amount of data received, avoiding
resource exhaustion of swiotlb (seen on x86_64 platform).
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect register access goes through a DCR bus bridge, which
allows only one outstanding transaction. And to make matters
worse, each TEMAC IP block contains two Ethernet interfaces, and
although they seem to have separate registers for indirect access,
they actually share the registers. Or to be more specific, MSW, LSW
and CTL registers are physically shared between Ethernet interfaces
in same TEMAC IP, with RDY register being (almost) specificic to
the Ethernet interface. The 0x10000 bit in RDY reflects combined
bus ready state though.
So we need to take care to synchronize not only within a single
device, but also between devices in same TEMAC IP.
This commit allows to do that with legacy platform devices.
For OF devices, the xlnx,compound parent of the temac node should be
used to find siblings, and setup a shared indirect_mutex between them.
I will leave this work to somebody else, as I don't have hardware to
test that. No regression is introduced by that, as before this commit
using two Ethernet interfaces in same TEMAC block is simply broken.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With little-endian and 64-bit support in place, the ll_temac driver can
now be used on x86 and x86_64 platforms.
And while at it, enable COMPILE_TEST also.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TEMAC and SDMA is big-endian, so make sure that all values in SDMA
buffer descriptors (cmdac_bd) are handled as big-endian, independent of the
host endianness. With all currently supported platforms being big-endian,
this change does not make a change for any of them.
Note, when using app3 and app4 for piggybacking skb pointers there is no
need to care about endianness, as neither TEMAC nor SDMA access app3 and
app4 in TX buffer descriptors.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the powerpc specific MMIO register access functions with the
generic big-endian mmio access functions, and add support for
little-endian access depending on configuration.
Big-endian access is maintained as the default, but little-endian can
be configured in device-tree binding or in platform data.
The temac_ior()/temac_iow() functions are replaced with macro wrappers
to avoid modifying existing code more than necessary.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of buffer descriptor APP4 field (32-bit) for storing skb pointer
obviously does not work on 64-bit platforms.
As APP3 is also unused, we can use that to store the other half of 64-bit
pointer values.
Contrary to what is hinted at in commit message of commit 15bfe05c8d
("net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit")
there are no other pointers stored in cdmac_bd.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support initialization with platdata, so the driver can be used on
non-device-tree platforms.
For currently supported device-tree platforms, the driver should behave
as before.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a side effect, a few error cases are fixed.
If of_iomap() of sdma_regs failed, no error code was returned. Fixed to
return -ENOMEM similar to of_iomap() fail of regs.
If sysfs_create_group() or register_netdev() failed, lp->phy_node was not
released.
Finally, the order in remove function is corrected to be reverse order
of what is done in probe, i.e. calling temac_mdio_teardown() last, so we
unregister the netdev that most likely is using the mdio_bus first.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inconsistent IS_ERR and PTR_ERR in cpsw_probe,
The proper pointer to use is clk instead of mode.
This issue was detected with the help of Coccinelle.
Fixes: 83a8471ba2 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* share more code across drivers
* new driver for MT7615 chipsets
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlzJfSQACgkQ130UHQKnbvUqiACfeNJFtx6+0CbEvDXDGKJ7a7Mx
w28An1uKNBgAKSbNoWny3ZFbOoHuApq9
=i9U/
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2019-05-01' of https://github.com/nbd168/wireless
mt76 patches for 5.2
* share more code across drivers
* new driver for MT7615 chipsets
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Replace "pass through" with a proper "fall through" annotation
in order to fix the following warning:
drivers/net/netdevsim/bus.c: In function ‘new_device_store’:
drivers/net/netdevsim/bus.c:170:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
port_count = 1;
~~~~~~~~~~~^~~
drivers/net/netdevsim/bus.c:172:2: note: here
case 2:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This fix is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally firmware messages are printed with debugging enabled only. It's
a good idea as firmware may print a lot of messages that normal users
don't need to care about.
However, on firmware crash, it may be very helpful to log all recent
messages. There is almost always a backtrace available as well as rought
info on the latest actions/state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some PCIE firmwares drop txstatus if pktid is 0 and make packet held in
host side and never be released. If that packet type is 802.1x, the
pend_8021x_cnt value will be always greater than 0 and show "Timed out
waiting for no pending 802.1x packets" error message when sending key to
dongle every time.
To be compatible with all firmwares, host should set txflow request id
from 1 instead of from 0.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/sfc/mcdi_port.c: In function ‘efx_mcdi_phy_decode_link’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:344:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/ethernet/sfc/mcdi_port.c:345:2: note: here
case MC_CMD_FCNTL_OFF:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some device ids were never released and does not exist.
Cleanup these.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA counters are 64 bit and we can fetch that to reduce
counter overflow, espesially on byte counters.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_nic_update_ndev_stats pushes statistics to ndev->stats from
system interface. This is not always good because it counts packets/bytes
before any of rx filters (including mac filter).
Its better to report the packet/bytes statistics from DMA
counters which gives actual values of data transferred over pci.
System level stats is still available via ethtool.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves ethtool -S usage, where stats are now actual
on each request. Before that stats only were updated at service
timer period.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service timer callback fetches statistics from FW and that may cause
a long delay in error cases. We also now need to use fw mutex
to prevent concurrent access to FW, thus - extract that logic
from timer callback into the job in the separate work queue.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of FW operations could be invoked simultaneously,
from f.e. ethtool context and from service service activity work.
Here we introduce a fw mutex to secure and serialize access
to FW logic.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typo in msi code. No much impact though.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve for better readability
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code detected link only after 1 sec is passed after up.
Here we replace this with direct service callback which updates
link status immediately
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we define and request an extra interrupt line,
assign it on link isr handler and restructure abit aq_pci code
to better support that.
We also remove logic for using different timer intervals
depending on link state, since thats now useless.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need this to schedule link interrupt handling and
various service tasks.
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define link interrupt handler
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare macroes and nic fields to support link interrupt
handling
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for hwmon api to fetch out chip temperature
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ability to read the chip temperature from memory
via hwmon interface
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not allocate mcu requests on the stack in mt7603_mcu_set_eeprom
in order to avoid the following warning:
Warning: the frame size of 1032 bytes is larger than 1024 bytes
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not enable/disable pre_tbtt_tasklet tasklet in
mt76x02_sw_scan/mt76x02_sw_scan_complete since it is already done
setting the operating channel. Do run tbtt_tasklet while the device is
offchannel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable pre_tbtt_tasklet tasklet before setting the operating channel.
Enable/disable beacon_timer in mt7603_set_channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move pre_tbtt_tasklet tasklet in mt76_dev data structure since
it is used by all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Announce antenna pattern cap to adapt PHY and baseband settings.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move beacon_mask in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move beacon_int in mt76_dev data structure since it is used by
all drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If buffer size is not usb_endpoint_maxp (512 or 1024 bytes) multiple,
usb host driver has to use bounce buffer and copy data. For RX we can
avoid that since we alreay allocate q->buf_size (2kB) buffers and
mt76usb hardware will not fill more data as rx packet size is limited
by network protocol. However add error message if this assumption
somehow will be not true.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Print fw_ver and build_date members of struct mt7603_fw_trailer
similarly to what appears in the output of 'dmesg' when the MCU firmware
is loaded.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix many warnings with incorrect endian assumptions.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes: ec7d2d74760a ("mt76: mt76x02: use napi polling for tx cleanup")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run __mt76_mcu_send_msg instead of __mt7603_mcu_msg_send and remove
duplicated code.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use common function wrapper in mt7603_mcu_exit since the code is shared
with mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use __mt76_mcu_send_msg wrapper instead of mt7603_mcu_msg_send.
This is a preliminary patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76 common signature for mt7603_mcu_msg_send. Move skb allocation
in mt7603_mcu_msg_send and remove duplicated code. This is a preliminary
patch for mt7615-mt7603 mcu code unification
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove query parameter from mt7603_mcu_msg_send/__mt7603_mcu_msg_send
routine signature since it can be obtained from cmd value. This is a
preliminary patch for mcu code unification between mt7615 and mt7603
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous version only accidentally disabled A-MSDU deaggregation by
using the wrong mask for rx length configuration, which left previous
length value in place.
Fix the length and initialize the register completely to keep A-MSDU
de-aggregation remaining disabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211 .start(), .stop() callbacks are never called concurrently with
other callbacks. The only concurencly is with mt76 works which we cancel
on stop() and schedule on start().
This fixes possible deadlock on cancel_delayed_work_sync(&dev->mac_work)
as mac_work also take mutex.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On suspend mac80211 .stop callback is called before .suspend(), so
hw mac is already stopped and we do not have to do this again.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use macro to convert sn and seq_ctrl for better readability.
Signed-off-by: Roy Luo <royluo@google.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the tx/rx fastpath, the funciton dma_map_single() rarely fails.
This adds unlikely() optimization to this error check conditional.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This driver is for a newer generation of MediaTek MT7615 4x4 802.11ac
PCIe-based chipsets, which support wave2 MU-MIMO up to 4 users/group
and also support up to 160MHz bandwidth.
The driver fully supports AP, station and monitor mode.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Roy Luo <royluo@google.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce skb check for dummy address in mt76_dma_tx_cleanup_idx.
This is a preliminary patch to add support for new chipsets (e.g. 7615)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce skb field in mt76_txwi_cache. Moreover add txwi_flags
to mt76_driver_ops since new chipsets will release mt76_txwi_cache/skbs
at tx completion instead of dma one.
This is a preliminary patch to add mt7615 support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Pass skb pointer to tx_prepare_skb through mt76_tx_info data structure.
This is a preliminary patch to properly support dma error path for
new chipsets (e.g. 7615)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dynamically allocate txwi since new chipsets will use longer txwi
descriptors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to pci counterpart, reduce locking in mt76u_tx_tasklet since
q->head is managed just in mt76u_tx_tasklet and q->queued is updated
holding q->lock
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mac_work delayed work in mt76_dev data structure since
it is used by all drivers and it will be reused adding mac work to
mt7615
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
q->tail can be safely updated without locking, because there is no
concurrent access. If called from outside of the tasklet (for flushing),
the tasklet is always disabled.
q->queued can be safely read without locking, as long as the decrement
happens within the locked section.
This patch allows cleaning up tx packets outside of the section that holds
the queue lock for improved performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- tx power is stored in the channels after ieee80211_register_hw, so
chan->orig_mpwr needs to be updated as well
- for non-TSSI devices, mt76x2e needs to use a different target power value
from the EEPROM
- fix a rounding error in a few places (need to round up, not down)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_tx_free in mt76_free_device routine in order to
unmap all txwi descriptors at module unload
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since now only mt76u_get_next_rx_entry use queue argument move
it to this function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Alloc sg table at the end of urb structure. This will increase
cache usage.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We already allocate with GFP_ZERO and sg marker is set later for
both RX and TX.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add new rx_urb_alloc routine and reuse common urb_alloc for tx
allocations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get the RX queue inside mt76u_refill_rx. This will allow to reuse
mt76u_urb_alloc for TX allocations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Put urb pointer in mt76_queue_entry directly instead of mt76u_buf
structure.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_queue_entry has alreay one bool variable, adding new one will
not increase it's size. Removing ->done filed from mt76u_buf will
allow to use urb directly in mt76usb code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Setup usb device private data. This allows to remove mt76u_buf->dev
and simplify some routines as no longer we need to get usb device
through usb interface.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We do not need to pass len and sglen to the function.
Additionally pass gfp to control allocation context.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We can not run mt76u_alloc_buf() concurently, rx_tasklet is stooped
when mt76u_submit_rx_buffers(). We can remove rx_page_lock.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unnecessery arguments and change the function name since is
now used only for RX.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable AP mode. For now without multi-vif support, this will require
more testing and investigation.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All mt76 drivers (now also USB drivers) require empty .set_tim
callback. Add it to common mt76 module and use on all drivers.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Create software MT_TXQ_PSD queue for USB and map it to MT_TXQ_VO
since we do not have USB endpoint for PSD. This should make
mt76_release_buffered_frames() work by sending released frames
via MT_TXQ_VO.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we sent PS buffered frames via beacon memory we need to make
beacon slots bigger. That imply we will also need to decrease number
of slots as beacon SRAM memory is limited to 8kB.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Program beacons data and PS buffered frames on TBTT work for USB.
We do not have MT_TXQ_PSD queue available via USB endpoints. The way
we can send PS broadcast frames in timely manner before PS stations go
sleep again is program them in beacon data area. Hardware do not modify
those frames since TXWI is properly configured. mt76x02_mac_set_beacon()
already handle this and free no longer used frames.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is required to sent multicast/broadcast frames in USB AP
mode just after beacon.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add sta_ps callback but dont set WCID drop sicne registers for USB
can not be accessed from tasklet context.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move some TBTT mmio functions to mt76x02_beacon.c and create new ones
in order to be reused by USB pre-TBTT.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add implementation of beacon_ops for USB and exit function to
stop the timer if running when device is removed. Still no
actual work on pre tbtt event.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enabling/disableing TBTT and beacon will be diffrent for USB. Introduce
beacon_ops to encapsulate that and implement it for MMIO. USB
implementation is noop for now.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add timer and work for pre TBTT for USB devices. For now code
doesn't do anyting useful, just add hrtimer which synchronize
with hardware MT_TBTT_TIMER.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move most of beaconing code into separate file and separate beacon
initialization for USB and MMIO as pre TBTT implementation for USB
will be different.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use register definitions instead of magic numbers in mt7603_reg_map
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt7603_mcu_init since mcu.mutex has been already initialized
in mt76_mmio_init. Run mt7603_load_firmware directly in
mt7603_init_hardware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As already done for mt76_dma_tx_queue_skb_raw, add static qualifier to
mt76_dma_tx_queue_skb and introduce mt76_tx_queue_skb in order to run
mt76_dma_tx_queue_skb in driver code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76_tx_info as auxiliary data structure to pass values
to tx_prepare_skb pointer. This is a preliminary patch to add
support for new chipsets (e.g. mt7615)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move skb dma mapping before configuring txwi since new chipsets (mt7615)
will need skb dma addresses in order to properly configure txwi
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce tx_aligned4_skbs in mt76_driver_ops and move
mt76_insert_hdr_pad in mt76_dma_tx_queue_skb. This is a preliminary
patch in order to unify tx dma mapping for mt76x02 and new chipsets
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_insert_hdr_pad in m76-core and rename it in
mt76_insert_hdr_pad in order to be used in mt76_dma_tx_queue_skb.
This is a preliminary patch in order to properly support tx dma
mapping for new chipsets (e.g. mt7615)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76_txq_id field to mt76_queue_entry in order to properly
track outstanding frames for mt7615 that relies on a single hw queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_sw_queue data structure in order to support new
chipsets (e.g. mt7615) that have a shared hardware queue for all traffic
identifiers. mt76_sw_queue will be used to track outstanding packets
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_queue dependency from tx_complete_skb function pointer and
rely on mt76_tx_qid instead. Remove flush from tx_complete_skb
signature. This is a preliminary patch to introduce mt76_sw_queue
support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_queue dependency from tx_prepare_skb function pointer and
rely on mt76_tx_qid instead. This is a preliminary patch to introduce
mt76_sw_queue support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_queue dependency from tx_queue_skb function pointer and
rely on mt76_tx_qid instead. This is a preliminary patch to introduce
mt76_sw_queue support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_init_tx_queue and mt76x02_init_rx_queue in mt76
module in order to be reused adding support for mt7603 driver
and remove duplicated code.
Squash mt76x02_init_tx_queue and mt76x02_init_rx_queue in
mt76_dma_alloc_queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_set_irq_mask in mt76 module in order to be reused
adding support for mt7603 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to Neil who reported the issue leading to this
workaround, the workaround is no longer needed since
version 5.0. So let's remove it.
This was the bug report leading to the workaround:
https://bugzilla.kernel.org/show_bug.cgi?id=201081
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fortunately in one place there's a comment explaining what toggling
this bit does. So let's create a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers rtl_eri_set_bits and rtl_eri_clear_bits to improve
readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In basically all eri function calls the type argument is ERIAR_EXGMAC.
Therefore make it the default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver can be probed as an mdio device, remove the legacy
DSA platform device probing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probing DSA devices as platform devices has been superseded by using
normal bus drivers. Add support for probing the mv88e6060 device as an
mdio device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DSA has recently learned to treat better with drivers that set
vlan_filtering_is_global, doing this is no longer required.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was recently introduced, so keeping state inside the driver is no
longer necessary.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver, recognizing that the .port_vlan_filtering callback was never
coming after the port left its parent bridge, decided to take that duty
in its own hands. DSA now takes care of this condition, so fix that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core is now able to do this check prior to calling the
.port_vlan_filtering callback, so tell it that VLAN filtering is global
for this particular hardware.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new mac80211 driver for Realtek 802.11ac wireless network chips.
rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode
functionalities. The firmware for both can be found at linux-firmware.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
For RTL8822BE: rtw88/rtw8822b_fw.bin
For RTL8822CE: rtw88/rtw8822c_fw.bin
And for now, only PCI buses (RTL8xxxE) are supported. We will add support
for USB and SDIO in the future. The bus interface abstraction can be seen
in this driver such as hci.h. Most of the hardware setting are the same
except for some TRX path or probing setup should be separated.
Supported:
* Basic STA/AP/ADHOC mode, and TDLS (STA is well tested)
Missing feature:
* WOW/PNO
* USB & SDIO bus (such as RTL8xxxU/RTL8xxxS)
* BT coexistence (8822B/8822C are combo ICs)
* Multiple interfaces (for now single STA is better supported)
* Dynamic hardware calibrations (to improve/stabilize performance)
Potential problems:
* static calibration spends too much time, and it is painful for
driver to leave IDLE state. And slows down associate process.
But reload function are under development, will be added soon!
* TRX statictics misleading, as we are not reporting status correctly,
or say, not reporting for "every" packet.
The next patch set should have BT coexistence code since RTL8822B/C are
combo ICs, and the driver for BT can be found after Linux Kernel v4.20.
So it is better to add it first to make WiFi + BT work concurrently.
Although now rtw88 is simple but we are developing more features for it.
Even we want to add support for more chips such as RTL8821C/RTL8814B.
Finally, rtw88 has many authors, listed alphabetically:
Ping-Ke Shih <pkshih@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Third set of fixes for 5.1.
iwlwifi
* fix an oops when creating debugfs entries
* fix bug when trying to capture debugging info while in rfkill
* prevent potential uninitialized memory dumps into debugging logs
* fix some initialization parameters for AX210 devices
* fix an oops with non-MSIX devices
* fix an oops when we receive a packet with bogus lengths
* fix a bug that prevented 5350 devices from working
* fix a small merge damage from the previous series
mwifiex
* fig regression with resume on SDIO
ath10k
* fix locking problem with crashdump
* fix warnings during suspend and resume
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcyGH/AAoJEG4XJFUm622b3AIH/R/Af8W3E69s1jLpbwVpcnKX
jucK1WePDwgTttUI4cmtpCIlLImTiiMxgWd+ku7tpwz4kMJWY8KOjrvwN3ulNGUr
R0Vbsyc/CXS41DtfZt8IpckF3ru1omtdmBTfMEermoPbZZNtx1j34Odkn0VtEcjW
7Ml7u6YfZc/tKgWmIO6afhqMRgnChWGhK76ayCF7/9YM17uSoGw+rdLIM8o20+jE
VwMbhvNuZILwTZ35mbi1Tnbz8dZr/1J7yMqrmfuZFkpLseWixcQ6zK53A8PTJ0Cf
6B+fiu7+9mUzNaqzuemlYrZ2PsGXprdjrBNaHcnRrc3+GZlilKcDFQQCPWrpmz8=
=WiMH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-04-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
Third set of fixes for 5.1.
iwlwifi
* fix an oops when creating debugfs entries
* fix bug when trying to capture debugging info while in rfkill
* prevent potential uninitialized memory dumps into debugging logs
* fix some initialization parameters for AX210 devices
* fix an oops with non-MSIX devices
* fix an oops when we receive a packet with bogus lengths
* fix a bug that prevented 5350 devices from working
* fix a small merge damage from the previous series
mwifiex
* fig regression with resume on SDIO
ath10k
* fix locking problem with crashdump
* fix warnings during suspend and resume
Also note that this pull conflicts with net-next. And I want to emphasie
that it's really net-next, so when you pull this to net tree it should
go without conflicts. Stephen reported the conflict here:
https://lkml.kernel.org/r/20190429115338.5decb50b@canb.auug.org.au
In iwlwifi oddly commit 154d4899e4 adds the IS_ERR_OR_NULL() in
wireless-drivers but commit c9af7528c3 removes the whole check in
wireless-drivers-next. The fix is easy, just drop the whole check for
mvmvif->dbgfs_dir in iwlwifi/mvm/debugfs-vif.c, it's unneeded anyway.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc().
We can't pass unclamped values to test_bit() or it results in an out of
bounds access beyond the end of the bitmap.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet). This patch makes sure this factory test
bit is cleared in config_init().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce specification for Geneve decap flow with encapsulation options
and allow creation of rules that are matching on Geneve TLV options.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When in switchdev mode, we would like to treat loopback RoCE
traffic (on eswitch manager) as RDMA and not as regular
Ethernet traffic
In order to enable it we add flow steering rule that forward RoCE
loopback traffic to the HW RoCE filter (by adding allow rule).
In addition we add RoCE address in GID index 0, which will be
set in the RoCE loopback packet.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow table supports three types of miss action:
1. Default miss action - go to default miss table according to table.
2. Go to specific table.
3. Switch domain - go to the root table of an alternative steering
table domain.
New table miss action was added - switch_domain.
The next domain for RDMA_RX namespace is the NIC RX domain.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pass the flow steering objects instead of their attributes
to fs_cmd in order to decrease number of arguments and in
addition it will be used to update object fields.
Pass the flow steering root namespace instead of the device
so will have context to the namespace in the fs_cmd layer.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Open events of type 'GENERAL' to all types of interfaces. Prior to this
patch, 'GENERAL' events were captured only by Ethernet interfaces. Other
interface types (non-Ethernet) were excluded and couldn't receive
'GENERAL' events.
Fixes: 5d3c537f90 ("net/mlx5: Handle event of power detection in the PCIE slot")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The mlx5 Sub-Function (SF) sub device will be introduced in
subsequent patches. It will be created as mediated device and
belong to mdev bus. It is necessary to treat dma operations on
PF, VF and SF in uniform way, hence reduce the dependency on
pdev pci dev struct and work directly out of newly introduced
'struct device' from previous patch.
This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently mlx5 core stores copy of the PCI device name in a
mlx5_priv structure and uses pr_warn, pr_err helpers.
Get rid of the copy of this name; instead store the parent device
pointer that contains name as well as dma specific parameters.
This also allows to use kernel's well defined dev_warn, dev_err, dev_dbg
device specific print routines.
This is also a preparation patch to access non PCI parent device in
future.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Stefan Schmidt says:
====================
ieee802154 for net 2019-04-25
An update from ieee802154 for your *net* tree.
Another fix from Kangjie Lu to ensure better checking regmap updates in the
mcr20a driver. Nothing else I have pending for the final release.
If there are any problems let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper pci_dev_id() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use new helper pci_dev_id() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Add region type checking during regions parsing to avoid attempts to
parse unsupported or illegal region types.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_fw_ini_get_trigger_len the driver allocates space for memory
regions regardless of their domain and in iwl_fw_ini_dump_trigger the
driver aborts trigger collection of disabled domain. This diff causes
unneeded memory allocation and traling zeros in the dump file.
Solve this behavior by enforcing domain checking in
iwl_fw_ini_get_trigger_len
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the dump info, the driver sets device_family to
IWL_FW_ERROR_DUMP_FAMILY_7 in case IWL_FW_ERROR_DUMP_FAMILY_7 is used or
IWL_FW_ERROR_DUMP_FAMILY_8 otherwise. This information is misleading and
incorrect since the driver sets the device family to 8 to any device that
is from family 8 and later, e.g. device family 9 is represented as 8 in
the dump.
Also, the device family enum is known only to the driver and
does not give any information to the FW developer
Change the device family to HW type to give propper data about the nic
in use.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to configure a periodic data collection
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add LMAC_ERROR_TABLE and UMAC_ERROR_TABLE region types and handle them
in the same way as we handle DEVICE_MEMORY.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In newer firmware images there's a command version TLV that
states, for each listed command or notification, which version
of the command and/or notification structure is used. Read and
keep this data to be able to use it in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have a solitary and inconspicous ` in the middle of a comment in
this function, which should not be there. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't use cancel_delayed_work_sync() inside the channel switch
notifications as they are handled synchronously as part of the RX path.
Fix that by replacing it with cancel_delayed_work(). This should be safe
as we don't really care whether the work is already started and in such
case we would disconnect anyway.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the TLC config command according to the
rates the peer supports, make sure that we aren't also
limited by our own rates, so take the minimum between the
peer's supported RX rates and our supported TX rates.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support fseq tlv and print fseq version to dmesg.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the interface that is requesting an FTM measurement is connected
to a BSS, it is possible that the FTM request was originated by an
RRM request from the AP. In this case the station needs to report
the measurement start time in terms of the TSF of the AP.
Since there is no indication in the FTM request itself if the TSF
is needed, always report the TSF if the station is associated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new definitions for the WoWLAN patterns API version 2 and support
for version 2 of the WoWLAN patterns command without implementing the
new features. With this commit we only supporting the existing
bitmask pattern match. Use the new version only if the TLV is set.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If for some reason the device gives us an RX interrupt before we're
ready for it, perhaps during device power-on with misconfigured IRQ
causes mapping or so, we can crash trying to access the queues.
Prevent that by checking that we actually have RXQs and that they
were properly allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will let us introduce a mechanism to start with rfkill
faked, and put 0 here to override it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
commit 2785ce008e ("iwlwifi: support new NVM response API")
seems forgot use correct channel_profile in iwl_get_nvm when call
iwl_init_sbands().
Fixes: 2785ce008e ("iwlwifi: support new NVM response API")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.
Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Fixes: f279294e9e ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:
[ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4
[ 233.602642] Hardware name: Google Scarlet (DT)
[ 233.602647] Call trace:
[ 233.602663] dump_backtrace+0x0/0x11c
[ 233.602672] show_stack+0x20/0x28
[ 233.602681] dump_stack+0x98/0xbc
[ 233.602690] ___might_sleep+0x154/0x16c
[ 233.602696] __might_sleep+0x78/0x88
[ 233.602704] mutex_lock+0x2c/0x5c
[ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[ 233.602757] net_rx_action+0x140/0x388
[ 233.602766] __do_softirq+0x1b0/0x35c
[...]
ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.
A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null
(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)
The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.
I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.
Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com
Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
-----BEGIN PGP SIGNATURE-----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=0U95
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The header file is the only thing preventing us from building the
driver in a cross-platform configuration, so move the structure
we are interested in to the global platform_data location
and enable compile testing.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Considering that in polling mode each link drop will be latched,
settings can't have changed if link was up and is up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Introduce BPF socket local storage map so that BPF programs can store
private data they associate with a socket (instead of e.g. separate hash
table), from Martin.
2) Add support for bpftool to dump BTF types. This is done through a new
`bpftool btf dump` sub-command, from Andrii.
3) Enable BPF-based flow dissector for skb-less eth_get_headlen() calls which
was currently not supported since skb was used to lookup netns, from Stanislav.
4) Add an opt-in interface for tracepoints to expose a writable context
for attached BPF programs, used here for NBD sockets, from Matt.
5) BPF xadd related arm64 JIT fixes and scalability improvements, from Daniel.
6) Change the skb->protocol for bpf_skb_adjust_room() helper in order to
support tunnels such as sit. Add selftests as well, from Willem.
7) Various smaller misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When I rebased Greg's patch, I accidentally left the old if block that
was already there. Remove it.
Fixes: 154d4899e4 ("iwlwifi: mvm: properly check debugfs dentry before using it")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We introduced a bug that prevented this old device from
working. The driver would simply not be able to complete
the INIT flow while spewing this warning:
CSR addresses aren't configured
WARNING: CPU: 0 PID: 819 at drivers/net/wireless/intel/iwlwifi/pcie/drv.c:917
iwl_pci_probe+0x160/0x1e0 [iwlwifi]
Cc: stable@vger.kernel.org # v4.18+
Fixes: a8cbb46f83 ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: c8f1b51e50 ("iwlwifi: allow different csr flags for different device families")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't check for the validity of the lengths in the packet received
from the firmware. If the MPDU length received in the rx descriptor
is too short to contain the header length and the crypt length
together, we may end up trying to copy a negative number of bytes
(headlen - hdrlen < 0) which will underflow and cause us to try to
copy a huge amount of data. This causes oopses such as this one:
BUG: unable to handle kernel paging request at ffff896be2970000
PGD 5e201067 P4D 5e201067 PUD 5e205067 PMD 16110d063 PTE 8000000162970161
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 2 PID: 1824 Comm: irq/134-iwlwifi Not tainted 4.19.33-04308-geea41cf4930f #1
Hardware name: [...]
RIP: 0010:memcpy_erms+0x6/0x10
Code: 90 90 90 90 eb 1e 0f 1f 00 48 89 f8 48 89 d1 48 c1 e9 03 83 e2 07 f3 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48 89 d1 <f3> a4 c3
0f 1f 80 00 00 00 00 48 89 f8 48 83 fa 20 72 7e 40 38 fe
RSP: 0018:ffffa4630196fc60 EFLAGS: 00010287
RAX: ffff896be2924618 RBX: ffff896bc8ecc600 RCX: 00000000fffb4610
RDX: 00000000fffffff8 RSI: ffff896a835e2a38 RDI: ffff896be2970000
RBP: ffffa4630196fd30 R08: ffff896bc8ecc600 R09: ffff896a83597000
R10: ffff896bd6998400 R11: 000000000200407f R12: ffff896a83597050
R13: 00000000fffffff8 R14: 0000000000000010 R15: ffff896a83597038
FS: 0000000000000000(0000) GS:ffff896be8280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff896be2970000 CR3: 000000005dc12002 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
iwl_mvm_rx_mpdu_mq+0xb51/0x121b [iwlmvm]
iwl_pcie_rx_handle+0x58c/0xa89 [iwlwifi]
iwl_pcie_irq_rx_msix_handler+0xd9/0x12a [iwlwifi]
irq_thread_fn+0x24/0x49
irq_thread+0xb0/0x122
kthread+0x138/0x140
ret_from_fork+0x1f/0x40
Fix that by checking the lengths for correctness and trigger a warning
to show that we have received wrong data.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During driver unload, hash/TCAM filter deletion doesn't wait for
completion.This patch deletes all the filters with completion before
clearing the resources.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_READ macro contains a return statement, making it not very
safe. Remove it by inlining the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_WRITE macro contains a return statement, making it not very
safe. Remove it by inlining the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass around priv, not ds. This will help with changing to an mdio
driver, and makes this driver more like mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an SPDX header, and remove the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently uses the same fixed name when using
request_irq, this makes it hard to parse when multiple VNIC devices are
available at the same time. This patch adds the unit_address as the device
identification along with an id for each queue.
The original idea was to use the interface name as an identifier, but it
is not feasible given these requests happen at adapter probe, and at this
point netdev is not yet registered so it doesn't have the proper name
assigned to it.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common ethtool functions to separate cpsw-ethtool.c file so that they
can be used across both drivers. It will simplify CPSW driver code
maintenance also.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch CPSW driver to use the new MAC SL API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC SL submodule has a lot of common functions between many of TI SoCs
AM335x/AM437x/DRA7(AM57xx), Keystone 2 66AK2HK/E/L/G and K3 AM654, but
there are also differences especially in registers offsets and sets of
supported functions.
This patch introduces the MAC SL submodule API which is intended to provide
a common way to access the MAC SL submodule and hide HW integrations
details.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move common hw init code in separate function as preparation for adding new
switchdev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_addr_t for desc_mem_phys and desc_hw_addr to avoid types
conversions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add a switchdev based cpsw driver move the common
header definitions to cpsw_priv.h. The plan is to develop a new driver on
switchdev driver model and obsolete the current cpsw driver after all
required functions are added to the new driver. This patch allows the same
header file to be re-used on both drivers during the transition period.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework probe to group common hw initialization:
- group resources request at the beginning of the probe
- move net device initialization and registration at the end of the probe
- drop cpsw_slave_init
as preparation of refactoring of common hw initialization code to
separate function.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO in most of the case implemented as module inside of TI
CPSW subsystem and fully depends on CPSW to be enabled, but historically
it's implemented as separate Platform device/driver and defined in DT files
in two ways:
- as standalone node
- as child node of CPSW subsystem.
In later case it's required to split CPSW subsystem "reg" property to
exclude MDIO I/O range which is not useful.
Hence, replace devm_ioremap_resource() with devm_ioremap() to allow define
full I/O range in parent CPSW subsystem without spliting.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not delete multicast supervisory packet's (SUPER) entries while flushing
multicast addresses from ALE table cpsw_ale_flush_multicast(). Those
entries have to be added/removed only explicitly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPSW ALE will set/clean Host port bit in Unregistered Multicast Flood
Mask (UNREG_MCAST_FLOOD_MASK) for every VLAN without checking if this port
belongs to VLAN or not when ALLMULTI mode flag is set for nedev. This is
working in non dual_mac mode, but in dual_mac - it causes
enabling/disabling ALLMULTI flag for both ports.
Hence fix it by adding additional parameter to cpsw_ale_set_allmulti() to
specify ALE port number for which ALLMULTI has to be enabled and check if
port belongs to VLAN before modifying UNREG_MCAST_FLOOD_MASK.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ALE_PORT_HOST define for host port in cpsw_ale_set_allmulti() instead
of constants.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct define ALE_SUPER for ALE Multicast Address Table Entry
Supervisory Packet (SUPER) bit setting instead of ALE_BLOCKED. No issues
were observed till now as it have never been set, but it's going to be used
by new CPSW switch driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unnecessary wrapper function cpsw_tx_packet_submit() which is used
only in one place.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_alloc_etherdev_mqs() and simplify code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop pinctrl_pm_select_default_state call from probe as default
pinctrl state is set by DD core.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use local variable struct device *dev in probe to simplify code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update cpsw_split_res() to accept struct cpsw_common instead of
struct net_device to simplify code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TI drivers CPSW/NETCP can't work without ALE, hence simplify
build of those drivers by always linking cpsw_ale and drop
CONFIG_TI_CPSW_ALE config option.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both drivers CPSW and EMAC can't work without CPDMA, hence simplify build
of those drivers by always linking davinci_cpdma and drop TI_DAVINCI_CPDMA
config option.
Note. the davinci_emac driver module was changed to "ti_davinci_emac" to
make build work.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace textual license with SPDX-License-Identifier.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_rx_pkt(), if the driver encounters BD errors, it will recycle
the buffers and jump to the end where the uninitailized variable "len"
is referenced. Fix it by adding a new jump label that will skip
the length update. This is the most correct fix since the length
may not be valid when we get this type of error.
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an earlier commit that fixes the number of stats contexts to
reserve for the RDMA driver, we added a function parameter to pass in
the number of stats contexts to all the relevant functions. The passed
in parameter should have been used to set the enables field of the
firmware message.
Fixes: 780baad44f ("bnxt_en: Reserve 1 stat_ctx for RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver determines that extended TX port statistics are not supported
or allocation of the data structure fails, make sure to pass 0 TX stats
size to firmware to disable it. The firmware returned TX stats size should
also be set to 0 for consistency. This will prevent
bnxt_get_ethtool_stats() from accessing the NULL TX stats pointer in
case there is mismatch between firmware and driver.
Fixes: 36e53349b6 ("bnxt_en: Add additional extended port statistics.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we encounter errors during open and proceed to clean up,
bnxt_hwrm_ring_free() may crash if the rings we try to free have never
been allocated. bnxt_cp_ring_for_rx() or bnxt_cp_ring_for_tx()
may reference pointers that have not been allocated.
Fix it by checking for valid fw_ring_id first before calling
bnxt_cp_ring_for_rx() or bnxt_cp_ring_for_tx().
Fixes: 2c61d2117e ("bnxt_en: Add helper functions to get firmware CP ring ID.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the bnxt_init_one() error path, short FW command request memory
is not freed. This patch fixes it.
Fixes: e605db801b ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver builds a list of multicast addresses and sends it to the
firmware when the driver's ndo_set_rx_mode() is called. In rare
cases, the firmware can fail this call if internal resources to
add multicast addresses are exhausted. In that case, we should
try the call again by setting the ALL_MCAST flag which is more
guaranteed to succeed.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves software connection manager on older Apple systems with
Thunderbolt 1 and 2 controller to support full PCIe daisy chains,
Display Port tunneling and P2P networking. There are also fixes for
potential NULL pointer dereferences at various places in the driver.
-----BEGIN PGP SIGNATURE-----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=nqM+
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into char-misc-next
Mika writes:
thunderbolt: Changes for v5.2 merge window
This improves software connection manager on older Apple systems with
Thunderbolt 1 and 2 controller to support full PCIe daisy chains,
Display Port tunneling and P2P networking. There are also fixes for
potential NULL pointer dereferences at various places in the driver.
* tag 'thunderbolt-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (44 commits)
thunderbolt: Make priority unsigned in struct tb_path
thunderbolt: Start firmware on Titan Ridge Apple systems
thunderbolt: Reword output of tb_dump_hop()
thunderbolt: Make rest of the logging to happen at debug level
thunderbolt: Make __TB_[SW|PORT]_PRINT take const parameters
thunderbolt: Add support for XDomain connections
thunderbolt: Make tb_switch_alloc() return ERR_PTR()
thunderbolt: Add support for DMA tunnels
thunderbolt: Add XDomain UUID exchange support
thunderbolt: Run tb_xdp_handle_request() in system workqueue
thunderbolt: Do not tear down tunnels when driver is unloaded
thunderbolt: Add support for Display Port tunnels
thunderbolt: Rework NFC credits handling
thunderbolt: Generalize port finding routines to support all port types
thunderbolt: Scan only valid NULL adapter ports in hotplug
thunderbolt: Add support for full PCIe daisy chains
thunderbolt: Discover preboot PCIe paths the boot firmware established
thunderbolt: Deactivate all paths before restarting them
thunderbolt: Extend tunnel creation to more than 2 adjacent switches
thunderbolt: Add helper function to iterate from one port to another
...
This way, slhc_free() accepts what slhc_init() returns, whether that is
an error or not.
In particular, the pattern in sl_alloc_bufs() is
slcomp = slhc_init(16, 16);
...
slhc_free(slcomp);
for the error handling path, and rather than complicate that code, just
make it ok to always free what was returned by the init function.
That's what the code used to do before commit 4ab42d78e3 ("ppp, slip:
Validate VJ compression slot parameters completely") when slhc_init()
just returned NULL for the error case, with no actual indication of the
details of the error.
Reported-by: syzbot+45474c076a4927533d2e@syzkaller.appspotmail.com
Fixes: 4ab42d78e3 ("ppp, slip: Validate VJ compression slot parameters completely")
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's meaningless to trigger reset when failed to send command to IMP,
because the failure is usually caused by no authority, illegal command
and so on. When that happened, we just need to return the status code
for further debugging.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the hns3_put_ring_config() to prevent
double free, and for more readable, move the NULL assignment of
priv->ring_data into the hns3_put_ring_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).
If not modified, the loopback test returns probability failure.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.
So this patch fixes it, only return while setting PFC failed.
Fixes: 44e59e375b ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.
Fixes: c59a85c07e ("net: hns3: stop sending keep alive msg to PF when VF is resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.
This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.
Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().
Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.
This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.
This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device may be shutdown without the hardware being reinitialized, in
which case we want to ensure we cleanup properly.
This is especially important for kexec with traffic flowing.
The shutdown procedures resembles the remove procedures, so we can reuse
those common tasks.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.
marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.
Fixes: 2170fef78a ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Apple products use the same protocol for tethering over USB.
To simplify the code and make it future proof, use
USB_VENDOR_AND_INTERFACE_INFO() instead of
USB_DEVICE_AND_INTERFACE_INFO() to automatically detect and support
all existing and future Apple products using the same interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, refactor code a
bit and mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/broadcom/cnic.c: In function ‘cnic_cm_process_kcqe’:
drivers/net/ethernet/broadcom/cnic.c:4044:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
opcode = L4_KCQE_OPCODE_VALUE_CLOSE_COMP;
drivers/net/ethernet/broadcom/cnic.c:4050:2: note: here
case L4_KCQE_OPCODE_VALUE_RESET_RECEIVED:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c: In function ‘fwevtq_handler’:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:520:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
cpl = (void *)p;
~~~~^~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:524:2: note: here
case CPL_SGE_EGR_UPDATE: {
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
In file included from drivers/net/wimax/i2400m/debug-levels.h:30,
from drivers/net/wimax/i2400m/control.c:86:
drivers/net/wimax/i2400m/control.c: In function ‘i2400m_report_tlv_system_state’:
./include/linux/wimax/debug.h:200:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
do { \
^
./include/linux/wimax/debug.h:404:36: note: in expansion of macro ‘_d_printf’
#define d_printf(l, _dev, f, a...) _d_printf(l, "", _dev, f, ## a)
^~~~~~~~~
drivers/net/wimax/i2400m/control.c:354:3: note: in expansion of macro ‘d_printf’
d_printf(1, dev, "entering BS-negotiated idle mode\n");
^~~~~~~~
drivers/net/wimax/i2400m/control.c:355:2: note: here
case I2400M_SS_DISCONNECTING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-drv.c: In function ‘xgbe_set_hwtstamp_settings’:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1614:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1616:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1625:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1627:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1636:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1638:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manage the -EPROBE_DEFER error case for "stm32_pwr_wakeup" IRQ.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c: In function 'rtl92cu_phy_rf6052_set_cck_txpower':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:45:7: warning: variable 'turbo_scanoff' set but not used [-Wunused-but-set-variable]
It is not used any more since
commit e9b0784bb9 ("rtlwifi: rtl8192cu: Fix some code in RF handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch modifies location of debugfs entries and their naming
conventions to support multiple wireless cards on pcie host.
Selected approach is to use separate directories for different
wireless cards in top-level qtnfmac debugfs directory.
Here is an example that clarifies the chosen naming conventions:
$ sudo ls /sys/kernel/debug/qtnfmac/
qtnfmac_pcie:0000:01:00.0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ETSI region DFS slave device can operate in two modes on DFS channels:
- do on-channel radar detection and use higher Tx power
- don't do radar detection and use lower Tx power as a consequence
Allow user to control that behavior through qtnfmac module parameter.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Channel switch events from firmware should be processed only when STA
is already connected to BSS. On connect this notification is not needed
since full BSS info will be supplied by cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allow Extended Key ID to be used with hwsim.
Hwsim can only communicate with other hwsim cards, allowing it to bypass
creation of A-MPDUs in the first place.
Mixing keyIDs in an A-MPDU is therefore impossible and can never cause
interoperability issues with other cards.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
P2P device interface type was not indicated in the supported
interface types even when hwsim was configured with p2p device
support. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement ndo_get_devlink_port and allow switch_id and port_name to be
handled by devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the existing way to create netdevsim over rtnetlink and move the
netdev creation/destruction to dev probe, so for every probed port,
a netdevsim-netdev instance is created.
Adjust selftests to work with new interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to test flows in core, it is beneficial to maintain previously
supported possibility to add and delete ports during netdevsim lifetime.
Do it by extending device sysfs attrs by "new_port" and "del_port".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement netdevsim bus probing of netdevsim devices. For every probed
device create a devlink instance. According to the user-passed value,
create a number of ports represented by devlink port instances.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the model where dev is represented by devlink and ports are
represented by devlink ports, make debugfs file names independent
on netdev names. Change the topology to the one illustrated
by the following example:
$ ls /sys/kernel/debug/netdevsim/
netdevsim1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/
bpf_bind_accept bpf_bind_verifier_delay bpf_bound_progs ports
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/
0 1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/
bpf_map_accept bpf_offloaded_id bpf_tc_accept bpf_tc_non_bound_accept bpf_xdpdrv_accept bpf_xdpoffload_accept dev ipsec
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -l
lrwxrwxrwx 1 root root 0 Apr 13 15:58 /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -> ../../../netdevsim1
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of parent_id/switch_id does not follow the
original idea of being unique. The values are "0", "1", etc. Instead of
that, generate 32 random bytes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously introduce dev which is mapped 1:1 to a bus device covers
the purpose of the original shared device, merge the sdev code into dev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are going to be called from bus probe/release(),
therefore make them independent on ns struct and rename accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a way to add new netdevsim device on netdevsim bus and also to
delete existing netdevsim device from the bus. Track the bus devices
in using a list.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of increments of u32 value, use ida to manage bus device ids.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
