This change replaces calls to rmb with dma_rmb in the case where we want to
order all follow-on descriptor reads after the check for the descriptor
status bit.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to e1000e_write_protect_nvm_ich8lan() is no longer supported by HW.
Access to these registers causes a system freeze in A step hardware and is
ignored in B step hardware. This function must not be called in hardware
newer than LPT.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When bringing down an interface netif_carrier_off() should be
one the first things we do, since this will prevent the stack
from queuing more packets to this interface.
This operation is very fast, and should make the device behave
much nicer when trying to bring down an interface under load.
Also, this would Do The Right Thing (TM) if this device has some
sort of fail-over teaming and redirect traffic to the other IF.
Move netif_carrier_off as early as possible.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Starting I219, the NVM will not be mapped to its own BAR, but to an
address region in another bar. The mapping/unmapping is relevant
to older HW only.
CC: John W Linville <linville@tuxdriver.com>
Reported-by: John W Linville <linville@tuxdriver.com>
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 is the next-generation LOM that will be available on systems with the
Sunrise Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Carmen Edwards <carmenx.edwards@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't update Tx tail descriptor if queue hasn't been stopped
and we know at least one more skb will be sent right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the Intel 82527EI (driver: e1000e) there is an issue when running
the ptpd2 program, that leads to a kernel oops. The reason is here that
in e1000_xmit_frame() a work queue will be scheduled that has not been
initialized in this case. The work queue "tx_hwstamp_work" will only be
initialized if adapter->flags & FLAG_HAS_HW_TIMESTAMP set. This check
is missing in e1000_xmit_frame().
The following patch adds the missing check.
Signed-off-by: Mathias Koehrer <mathias.koehrer@etas.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME within #ifdef blocks depending on
CONFIG_PM may be dropped now.
Do that in the e1000e and igb network drivers.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO support for vlans. It also allows a
user to control vlan acceleration offloading. As such, it is
possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information. This results
in corrupted frames sent on the wire. Corruptions include
incorrect IP total length and invalid IP checksum.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a function, and associated calls, to flush writes to (read) the LPIC
MAC register before entering the shutdown flow. This fixes the problem
of the PHY never negotiating a 100M link (if both sides of the link support
EEE and 100M link) when Runtime PM is enabled.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The process of shutting down the system causes a call to the close PM
callback. The reset in close causes a loss of link, and the resultant
LSC interrupt causes the Runtime PM idle callback to be called. The
check for link (while link is down) in the idle callback is wiping the
information about the EEE ability of the link partner. The information is
still gone when the PHY is powered back up in the shutdown flow. This
causes EEE in S5 to fail when Runtime PM is active.
Save the link partner's EEE ability in the idle callback so that a Runtime
PM event will not cause a loss of this information.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding code to check and respond to previously ignored return values
from NVM access functions.
Issue discovered through static analysis.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Out of lining these two common inlines saves about 30k text size,
due to their errata workarounds.
14131431 2008136 1507328 17646895 10d452f vmlinux-before-e1000e
14101415 2004040 1507328 17612783 10cbfef vmlinux-e1000e
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the update_phy_task was only calling e1000_set_eee_pchlan()
for phy.type 82579. This patch is to cause this function to be called
for 82579 and newer phy.types. This causes the dev_spec->eee_lp_ability
to have the correct value when going into SX states.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to a synchronization error, the value read from SYSTIML/SYSTIMH
might be incorrect.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the check to turn on promiscuous mode only took into account
the total number of SHared Receive Address (SHRA) registers and if the
request was for a register within that range. It is possible that the
Management Engine might have locked a number of SHRA and not allowed a
new address to be written to the requested register.
Add a function to determine the number of unlocked SHRA registers. Then
determine if the number of registers available is sufficient for our needs,
if not then return -ENOMEM so that UNICAST PROMISC mode is activated.
Since the method by which ME claims SHRA registers is non-deterministic,
also add a return value to the function attempting to write an address
to a SHRA, and return a -E1000_ERR_CONFIG if the write fails. The error
will be passed up the function chain and allow the driver to also set
UNICAST PROMISC when this happens.
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixing "WARNING:SPACING: networking uses a blank line after declarations"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing occurrences of returning 0 and 1 from bool functions to false and
true, respectively
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
static int e1000e_pm_thaw(struct device *dev)
^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When changing the interface mtu, the driver starts with a value
that doesn't include VLAN_HLEN. Later tests in the driver
set the rx_buffer_len based on the mtu. As a result, when
the user increases the mtu to 1504 (to support 802.1AD for example),
the driver rx_buffer_len does not change and frames longer
the 1522 bytes are rejected as too long.
Include VLAN_HLEN from the start so that an user mtu greater then
1500 bytes is correctly reflected in the driver rx_buffer_len.
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit da1e2046e5, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function. The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.
After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values. This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.
The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.
Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_hwtstamp_skb is always set before work is scheduled,
work is cancelled before tx_hwtstamp_skb is set to NULL.
PTP work cannot ever see tx_hwtstamp_skb set to NULL.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware may fail to report time stamp e.g.:
- when hardware time stamping is not enabled
- when time stamp is requested shortly after ifup
Timeout time stamp reading work to prevent it from
scheduling itself indefinitely. Report timeout events
via system log and device stats.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost. It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.
Move the check back to the place it was before in the watchdog task. Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 2800209994 (e1000e: Refactor PM flows) changed the
SET_SYSTEM_SLEEP_PM_OPS to open-coded assignment, but forgot to
protect them with CONFIG_PM_SLEEP. Then cause the following build
error when PM is disabled:
drivers/net/ethernet/intel/e1000e/netdev.c:7079:13:
error: 'e1000e_pm_suspend' undeclared here (not in a function)
.suspend = e1000e_pm_suspend,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7080:13:
error: 'e1000e_pm_resume' undeclared here (not in a function)
.resume = e1000e_pm_resume,
^
drivers/net/ethernet/intel/e1000e/netdev.c:7082:11:
error: 'e1000e_pm_thaw' undeclared here (not in a function)
.thaw = e1000e_pm_thaw,
^
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ULP is a power saving feature that reduces the power consumption of the
PHY when a cable is not connected.
ULP is gated on the following conditions:
1) The hardware must support ULP. Currently this is only I218
devices from Intel
2) ULP is initiated by the driver, so, no driver results in no ULP.
3) ULP's implementation utilizes Runtime Power Management to toggle its
execution. ULP is enabled/disabled based on the state of Runtime PM.
4) ULP is not active when wake-on-unicast, multicast or broadcast is active
as these features are mutually-exclusive.
Since the PHY is in an unavailable state while ULP is active, any access
of the PHY registers will fail. This is resolved by utilizing kernel
calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync)
and then, after PHY access is complete, allow the device to resume
Runtime PM (e.g. pm_runtime_put_sync).
Under certain conditions, toggling the LANPHYPC is necessary to disable
ULP mode. Break out existing code to toggle LANPHYPC to a new function
to avoid code duplication.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix issues with:
RuntimePM causing the device to repeatedly flip between suspend and resume
with the interface administratively downed.
Having RuntimePM enabled interfering with the functionality of Energy
Efficient Ethernet.
Added checks to disallow functions that should not be executed if the
device is currently runtime suspended
Make runtime_idle callback to use same deterministic behavior as the igb
driver.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the system power management flows to prevent the suspend path from
being executed twice when hibernating since both the freeze and
poweroff callbacks were set to e1000_suspend() via SET_SYSTEM_SLEEP_PM_OPS.
There are HW workarounds that are performed during this flow and calling
them twice was causing erroneous behavior.
Re-arrange the code to take advantage of common code paths and explicitly
set the individual dev_pm_ops callbacks for suspend, resume, freeze,
thaw, poweroff and restore.
Add a boolean parameter (reset) to the e1000e_down function to allow
for cases when the HW should not be reset when downed during a PM event.
Now that all suspend/shutdown paths result in a call to __e1000_shutdown()
that checks Wake on Lan status, removing redundant check for WoL in
e1000_power_down_phy().
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is to update the GPL header by removing the portion that
refers to the Free Software Foundation address.
Change the copyright date for 2014.
Reformat the header comments to conform to kernel networking coding norms
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enabling EEE LPI sooner than one second after link up on 82579 causes link
issues with some switches.
Remove EEE enablement for 82579 parts from the link initialization flow to
avoid initializing too early. EEE initialization for 82579 will be done
in e1000e_update_phy_task.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleaning up some pointer references that are no longer necessary
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7509963c70 (e1000e: Fix a compile flag mis-match for
suspend/resume) moved suspend and resume hooks to be available when
CONFIG_PM is set. However, it can be set even if CONFIG_PM_SLEEP is not set
causing following warnings to be emitted:
drivers/net/ethernet/intel/e1000e/netdev.c:6178:12: warning:
‘e1000_suspend’ defined but not used [-Wunused-function]
drivers/net/ethernet/intel/e1000e/netdev.c:6185:12: warning:
‘e1000_resume’ defined but not used [-Wunused-function]
To fix this make the hooks to be available only when CONFIG_PM_SLEEP is set
and remove CONFIG_PM wrapping from driver ops because this is already
handled by SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Dave Ertman <davidx.m.ertman@intel.com>
Cc: Aaron Brown <aaron.f.brown@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a mis-match between the declaration and usage of
the e1000_suspend and e1000_resume functions. Previously, these
functions were declared in a CONFIG_PM_SLEEP wrapper, and then utilized
within a CONFIG_PM wrapper. Both the declaration and usage will now be
contained within CONFIG_PM wrappers.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
e1000e_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it copies the configuration to
the e1000_adapter structure before validating it at all.
Change e1000e_config_hwtstamp() to take a pointer to the
hwstamp_config and to copy the config after validating it.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
The fallback to 32-bit DMA mask is rather odd:
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err) {
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
if (!err)
pci_using_dac = 1;
} else {
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32));
if (err) {
err = dma_set_coherent_mask(&pdev->dev,
DMA_BIT_MASK(32));
if (err) {
dev_err(&pdev->dev,
"No usable DMA configuration, aborting\n");
goto err_dma;
}
}
}
This means we only set the coherent DMA mask in the fallback path if
the DMA mask set failed, which is silly. This fixes it to set the
coherent DMA mask only if dma_set_mask() succeeded, and to error out
if either fails.
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removing a comparison to the boolean value true where simply interrogating
the lvalue will produce the same result.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While doing shutdown on the PCI device, the corresponding callback
function e1000e_shutdown() is trying to clear those correctable
errors on the upstream P2P bridge. Unfortunately, we don't have
the upstream P2P bridge under some cases (e.g. PCI-passthrou for
KVM on Power). That leads to kernel crash eventually.
The patch adds one more check on that to avoid kernel crash.
Signed-off-by: Li Zhang <zhlcindy@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch attempts to work around a problem found with some systems where
the call to pci_diable_link_state_locked() fails. As a result, ASPM is not,
in fact, disabled. Changing disable ASPM code to check if state actually
is disabled after the call and, if not, try another way to disable it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is runtime suspended (e.g. when there is no link), do not
wake it from D3 to read the PHY status; just set the values to typical
power-on defaults as is done when runtime PM is not enabled and there is no
link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as
I217 and same PHY as I218.
The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alter the packet buffer allocation accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The jumbo frame configuration in the MAC/PHY should be reverted on 82579
and newer parts when the interface is brought down (not just when the MTU
is changed back to standard frame size) otherwise iAMT connections (e.g.
SoL, IDE-R) will be dropped and cannot be re-acquired until the MTU is
changed again.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_ring/rx_ring size is assigned in function e1000_alloc_queues(), which is
called by e1000_sw_init() in the early stage of e1000_probe().
This patch just remove the duplicate assignment of this default ring size
value.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Da Yu Qiu <qiudayu@cn.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In attempting to resolve a minor merge conflict, commit e5f2ef7ab4
(Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net) accidentally
dropped a call to pci_clear_master() that was intended to remain in place.
Commit 4e0855dff0 (e1000e: fix pci-device enable-counter balance)
replaced a call to pci_disable_device() by one to pci_clear_master(). And then
commit 66148babe7 (e1000e: fix runtime power management transitions)
deleted a number of lines starting two lines following that call.
This patch restores the call to pci_clear_master() in __e1000_shutdown().
v2: added summary lines (enclosed in parens) following commit IDs
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An "unable to handle kernel paging request" panic can occur when receiving
traffic while the interface is going down. Wait for NAPI to be done with
current context after disabling interrupts and then disable NAPI.
See https://bugzilla.vyatta.com/show_bug.cgi?id=8837.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled. In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one. In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After dma_map_page, dma_mapping_error must be called. It seems safe to
not free the skb/page allocated in this function, as the skb/page can be
reused later.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cuddle broken lines where appropriate.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CHECK:SPACING: No space is necessary after a cast
CHECK:SPACING: space prohibited before semicolon
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING:LEADING_SPACE: please, no spaces at the start of a line
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING:LONG_LINE: line over 80 characters
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR:SPACING: spaces prohibited around that ':' (ctx:WxV)
ERROR:SPACING: need consistent spacing around '-' (ctx:WxV)
ERROR:SPACING: space required after that ',' (ctx:VxV)
ERROR:SPACING: spaces required around that '=' (ctx:VxV)
WARNING:SPACING: missing space after enum definition
and some similar spacing issues not reported by checkpatch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ERROR:CODE_INDENT: code indent should use tabs where possible
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes some annoying messages like 'Error reading PHY register' and
'Hardware Erorr' and saves several seconds on reboot.
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes redundant actions from driver and fixes its interaction
with actions in pci-bus runtime power management code.
It removes pci_save_state() from __e1000_shutdown() for normal adapters,
PCI bus callbacks pci_pm_*() will do all this for us. Now __e1000_shutdown()
switches to D3-state only quad-port adapters, because they needs quirk for
clearing false-positive error from downsteam pci-e port.
pci_save_state() now called after clearing bus-master bit, thus __e1000_resume()
and e1000_io_slot_reset() must set it back after restoring configuration space.
This patch set get_link_status before calling pm_runtime_put() in e1000_open()
to allow e1000_idle() get real link status and schedule first runtime suspend.
This patch also enables wakeup for device if management mode is enabled
(like for WoL) as result pci_prepare_to_sleep() would setup wakeup without
special actions like custom 'enable_wakeup' sign.
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes redundant and unbalanced pci_disable_device() from
__e1000_shutdown(). pci_clear_master() is enough, device can go into
suspended state with elevated enable_cnt.
Bug was introduced in commit 23606cf5d1
("e1000e / PCI / PM: Add basic runtime PM support (rev. 4)") in v2.6.35
Cc: Bruce Allan <bruce.w.allan@intel.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed. As a result, users suspect that there is something wrong with
NIC. If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names). These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions. Use those instead of redundant local
defines.
Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).
Some whitespace issues in the surrounding context of the above changes are
also cleaned up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the unused parameter when possible, otherwise use __always_unused
attribute.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this. To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set. Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the standard #defines for PCIe Capability ASPM fields.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup a set of conditional tests.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The removed code block is duplicated in e1000e_write_itr() so use that
instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(... to printk(KERN_INFO ...
v2 - remove unnecessary "e1000e:" prefix as pointed out by Joe Perches
since that produces a redundant "e1000e:" in the log message
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there is heavy traffic and the cable is pulled, the driver must reset
the adapter to flush the Tx queue in hardware. This causes the reset path
to be scheduled and logs the message "Reset adapter" which could be mis-
interpreted as an error by the user. Change how the reset path is invoked
for this scenario by using the same method done in an existing work-around
for 80003es2lan (i.e. set a flag and if the flag is set in the reset code
do not log the "Reset adapter" message since the reset is expected).
Re-name the FLAG_RX_RESTART_NOW to FLAG_RESTART_NOW since it is used for
resets in both the Rx and Tx specific code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update comments to conform to the preferred style for networking code as
described in ./Documentation/CodingStyle and checked for in the recently
added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a HW requirement. Although a buffer as short as 1 byte is allowed,
the total length of packet before, padding and CRC insertion, must be at
least 17 bytes. So pad all small packets manually up to 17 bytes before
delivering them to HW.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.
Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled. Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.
Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.
To avoid possible Tx stalls, change WTHRESH back to 1.
The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.
please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3bc1
Author: Tom Herbert <therbert@google.com>
Date: Mon Nov 28 16:33:16 2011 +0000
e1000e: Support for byte queue limits
Changes to e1000e to use byte queue limits.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i218 is the next-generation LOM that will be available on systems with the
Lynx Point LP Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support of those devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Early Receive has been disabled in the driver so this comment is no longer
applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add comments to memory barriers per strict checkpatch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PCI Express Capability access functions to simplify e1000e driver.
[bhelgaas: split e1000e and igb into separate patches]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
When configuring interrupt throttling on 82574 in MSI-X mode, we need to
be programming the EITR registers instead of the ITR register.
-rc2: Renamed e1000_write_itr() to e1000e_write_itr(), fixed whitespace
issues, and removed unnecessary !! operation.
-rc3: Reduced the scope of the loop variable in e1000e_write_itr().
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a report from Ethan Zhao, before calling register_netdev() the
driver should be using logging macros that do not display the potentially
confusing "(unregistered net_device)" yet still display the useful driver
name and PCI bus/device/function.
Reported-by: Ethan Zhao <ethan.kernel@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 44abd5c127 introduced NULL pointer
dereferences when attempting to access the check_reset_block function
pointer on 8257x and 80003es2lan non-copper devices.
This fix should be applied back through 3.4.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i217 is the next-generation LOM that will be available on systems with the
Lynx Point Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support for the device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Version bump to 1.11.3-k.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For the 82573, ASPM L1 gets disabled wholesale so this special-case code
is not required. For the 82574 the previous patch does the same as for
the 82573, disabling L1 on the adapter. Thus, this code is no longer
required and can be removed.
Signed-off-by: Chris Boot <bootc@bootc.net>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, IPv6 extension header parsing was disabled for all devices
supported by e1000e when using packet split mode. However, as per a
silicon errata, only certain devices need this restriction and will need
to disable IPv6 extension header parsing for all modes.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a known issue in the 82577 and 82578 device that can cause a hang
in the device hardware during traffic stress; the current workaround in the
driver is to disable transmit flow control by default. If the user enables
transmit flow control and the device hang occurs, provide a message in the
syslog suggesting to re-enable the workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Secondary unicast and multicast addresses are added to the Receive
Address registers (RAR) for most parts supported by the driver. For
82579, there is only one actual RAR and a number of Shared Receive Address
registers (SHRAR) that are shared among the driver and f/w which can be
reserved and write-protected by the f/w. On this device, use the SHRARs
that are not taken by f/w for the additional addresses.
Add a MAC ops function pointer infrastructure (similar to other MAC
operations in the driver) for setting RARs, introduce a new rar_set
function for 82579 and convert the existing code that sets RARs on other
devices to a generic rar_set function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some Rx and Tx specific registers are arrays indexed by the queue number.
For clarity, specify the intended queue rather than obscuring it behind a
define.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename NAPI polling routine and a parameter with more appropriate names,
refactor a conditional branch to get rid of an unnecessary goto/label and
fix a line exceeding 80 columns.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the first phrase of a multi-line comment to the second line.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
