Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i843 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
PG 1.0/1.1 silicon has limitations w.r.t frequencies at which MMC1/2/3
can operate.
Use soc_device_match() to identify rev 1.0/1.1 silicon and
override mmc->f_max according to the errata workaround.
"max-frequency" dt property cannot be used since the device
tree is added for rev 2.0 silicon.
soc_device_match() is also used in order to get the IODelay values
for rev 1.0/1.1 silicon.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci can directly get ADMA capability from MMCHS_CAPA register.
Remove explicitly setting ADMA here as some instances might not have
ADMA enabled. (sdhci_read_caps() is also removed from here since
sdhci_setup_host() invokes it).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Remove the local_irq_save() invocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While performing R/W access in PIO mode, the common SDHCI driver checks
the buffer ready status once per whole block processing. That is, after
getting an appropriate interrupt, or checking an appropriate status bit,
the driver makes buffer accesses for the whole block size (e.g. 128 reads
for 512 bytes block). This is done in accordance with SD Host Controller
Specification.
At the same time, the Ultra Secured Digital Host Controller (uSDHC), used
in i.MX6 (and, probably, earlier i.MX series too), uses a separate
Watermark Levels register, controlling the amount of data or space
available when raising status bit or interrupt. For default watermark
setting of 16 words, the controller expects (and guarantees) no more
than 16 buffer accesses after raising buffer ready status bit and
generating an appropriate interrupt. If the driver tries to access the
whole block size, it will get incorrect data at the end, and a new
interrupt will appear later, when the driver already doesn't expect it.
This happens sometimes, more likely on low frequencies, e.g. when
reading EXT_CSD at MMC card initialization phase
(which makes that initialization fail).
Such behavior of i.MX uSDHC seems to be non-compliant
to SDHCI Specification, but this is the way it works now.
In order not to rewrite the SDHCI driver PIO mode access logic,
the IMX specific driver can just set the watermark level to default
block size (128 words or 512 bytes), so that the controller behavior
will be consistent to generic specification. This patch does this
for PIO mode accesses only, restoring default values for DMA accesses
to avoid any possible side effects from performance point of view.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.
SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During probe check whether the vdd-io regulator of sdhc platform device
can support 1.8V and 3V and store this information as a capability of
platform device.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've successfully tested eMMC on R8A77980/Condor. R8A77980 has a single
SDHI core anyway, so can't be a subject of the known RX DMA errata...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the code block inside the for loop will never execute more than
once, because the function returns immediately after the first iteration,
hence the execution of the code at the second iteration is structurally
dead and, code at line 281: return 0; is never reached.
Fix this by checking _ret_ before return.
Addresses-Coverity-ID: 1468009 ("Logically dead code")
Addresses-Coverity-ID: 1468002 ("Structurally dead code")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call msdc_drv_probe() is to match an entry in
msdc_of_ids[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix 3.3V voltage switch for some BYT-based Intel controllers by making use
of the ACPI DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The WARN can never trigger because we limited the max_seg number in
renesas_sdhi_of_data already. Remove it and update the comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Whitelisting every ES version does not scale. So, we whitelist whole
SoCs independent of ES version. If we need specific handling for an ES
version, we put it to the front, so it will be matched first.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometimes sg->offset is not used for buffer addresses allocated by
dma_map_sg(), so alignment checks should be done on the allocated buffer
addresses. Delete the alignment check for sg->offset that is done before
dma_map_sg(). Instead, it performs the alignment check for
sg->dma_address after dma_map_sg().
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: broke this commit in two and tidied small style issue]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of directly accessing the members of struct scatterlist use the
helpers mmc_get_dma_dir() and sg_dma_address() in
renesas_sdhi_internal_dmac_start_dma(). Based on previous work by
Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some NI 904x devices, using 3.3V signaling for extended periods of
time will physically damage the pads connected to the SDHC, eventually
causing complete failure of the controller. To work around this,
require that we avoid 3.3V signaling.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our set_ios hook is, when the card is power up or down, either doing a full
init or put our controller back into a reset mode.
Since we're also doing that in our runtime_pm hooks, and at possibly much
more often, we can drop it from the set_ios, and either rely on our
runtime_pm hooks or our probe to do it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far, even if our card was not in use, we didn't shut down our MMC
controller, which meant that it was still active and clocking the bus.
While this obviously means that we could save some power there, it also
creates issues when it comes to EMC control since we'll have a perfect peak
at the card clock rate.
Let's implement runtime_pm with autosuspend so that we will shut down the
controller when it's not been in use for quite some time.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the card setup
to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the clock setup
to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the bus width
setup to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the other functions in the driver take a struct sunxi_mmc_host pointer.
Let's make it consistent.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DDR52 with 8-bit mode should be handled in a different way when
requesting ciu_clk. However DDR50 is used for SDMMC/SDIO and
could never be possible with 8-bit mode. It's trival but misleading.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Explicitly update the docomentation to support the Meson-AXG platform.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Introduce the compatible data to cover the register offset & mask
change of the eMMC controller in Amlogic's Meson-AXG SoC.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace dma_request_channel() with dma_request_chan(),
which also supports probing from the devicetree.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the JZ4780 MMC controller to the jz47xx_mmc driver. There
are a few minor differences from the 4740 to the 4780 that need to be
handled, but otherwise the controllers behave the same. The IREG and IMASK
registers are expanded to 32 bits. Additionally, some error conditions are
now reported in both STATUS and IREG. Writing IREG before reading STATUS
causes the bits in STATUS to be cleared, so STATUS must be read first to
ensure we see and report error conditions correctly.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The maximum clock rate can be overridden by DT. The clock rate should
be set to the DT-specified value rather than the constant JZ_MMC_CLK_RATE
when this is done. If the maximum clock rate is not set by DT then
mmc->f_max will be set to JZ_MMC_CLK_RATE.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to probe the device via devicetree, which
will be used to support other SoCs such as the JZ4780.
Based on commits from the CI20 repo, by Paul Cercueil
and Alex Smith. Binding document based on work by
Zubair Lutfullah Kakakhel.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case a bootloader leaves the device in a bad state,
requesting the interrupt before resetting results in a bad
interrupt loop.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
[Ezequiel: cleanup commit description]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of accessing the platform data pointer directly,
use the dev_get_platdata() helper.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a minor cleanup to order the headers alphabetically.
This helps prevent merge conflicts.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, if jz4740_mmc_request_gpios() fails, the driver
tries to release DMA resources. This is wrong because DMA
is requested at a later stage.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[Ezequiel: cleanup commit message]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently driver is using a VLA declared using the number of descriptors. This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values. Memory is
free'd before return from function.
>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On SD 2.00 cards we get lots of these messages:
"mmc0: Got data interrupt 0x00000002 even though no data operation was in progress"
By applying the SDHCI_QUIRK2_STOP_WITH_TC quirk, the messages no longer happen.
A single card claiming to be SD 3.00 compliant also generates the interrupts,
but since the card's manfacturing date is 2002 mar, it's unlikely to really be
SD 3.00. This card is a 8GB SanDisk 'SU08G' 8.0 (SDHC class 4).
This has been reported on Xilinx devices that also use the Arasan IP.
See https://patchwork.kernel.org/patch/8062871/
This has been tested on the Renesas RZ/ND-DB board with the RZ/N1 SoC. The
Arasan IP in this device is version 1.39a and uses a max SD clock of 50MHz and
does not support DDR modes.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode
- renesas_sdhi_internal_dmac: Avoid data corruption by limiting DMA RX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jO/Y
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode
- renesas_sdhi_internal_dmac: Avoid data corruption by limiting
DMA RX"
* tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs
mmc: sdhci-pci: Only do AMD tuning for HS200
Early revisions of certain SoCs cannot do multiple DMA RX streams in
parallel. To avoid data corruption, only allow one DMA RX channel and
fall back to PIO, if needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit c31165d740 ("mmc: sdhci-pci: Add support for HS200 tuning mode
on AMD, eMMC-4.5.1") added a HS200 tuning method for use with AMD SDHCI
controllers. As described in the commit subject, this tuning is specific
for HS200. However, as implemented, this method is used for all host
timings, because platform_execute_tuning, if it exists, is called
unconditionally by sdhci_execute_tuning(). This breaks tuning when using
the AMD controller with, for example, a DDR50 SD card.
Instead, we can implement an amd execute_tuning wrapper callback, and
then conditionally do the HS200 specific tuning for HS200, and otherwise
call back to the standard sdhci_execute_tuning().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: c31165d740 ("mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
If an error was detected when CMD23 was issued, command sequence should
be terminated with errors and CMD23 should be issued after retuning.
Fixes: 8b22c3c18b ("mmc: tmio: add CMD23 support")
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.
Fix the bug by dropping the reference for the bus in mmc_blk_exit().
Signed-off-by: Alexander Kappner <agk@godking.net>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.
If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.
This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).
Resolve by holding the spinlock until after the IMASK register has
been updated.
Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb856 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Pd6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic"
* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
mmc: update sdio_claim_irq documentation
mmc: Export host capabilities to debugfs.
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: block: fix updating ext_csd caches on ioctl call
mmc: sunxi: Set our device drvdata earlier
mmc: sunxi: Move the reset deassertion before enabling the clocks
mmc: sunxi: Move resources management to separate functions
mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
mmc: core: Export card RCA register via sysfs
mmc: renesas_sdhi: fix WP detection
mmc: core: Use memdup_user() rather than duplicating its implementation
mmc: dw_mmc-rockchip: correct property names in debug
mmc: sd: Remove redundant err assignment from mmc_read_switch
mmc: sdio: Check the return value of sdio_enable_4bit_bus
mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
arm64: dts: hi3660: remove 'num-slots' property for dwmmc
ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
arm64: dts: stratix10: remove 'num-slots' property for dwmmc
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The blackfin architecture is getting removed, so this one
is obsolete now as well.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All our documentation says HOST_MODE, we don't really know where EXT_ACC
came from. Rename it to reduce the confusion.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice
Signed-off-by: Joel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports the host capabilities to debugfs
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Zero is a valid IRQ number and is being used on some CHT tablets. Stop
treating it as an error.
Reported-by: Luke Ross <luke@lukeross.name>
Fixes: 1b7ba57ecc ("mmc: sdhci-acpi: Handle return value of platform_get_irq")
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.
That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.
Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.
Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.
And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the pm_runtime_enable hook is called, our runtime_suspend and
runtime_resume hooks can be called as well. However, we only set the device
drvdata that we will use after we have registered into the MMC core. Move
that earlier so that we don't have a race that could lead to a crash.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As per Allwinner guidelines, the reset line should be deasserted before
turning the clocks on.
Implement it in our driver as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've had all our resources management, and especially the clocks and reset
sequence, done directly as part of the probe.
As we want to implement runtime_pm, we'll obviously want to have that
moved outside of the probe so that we can call do it in our runtime suspend
and resume hooks without too much duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hi3798CV200 SoC extends the dw-mshc controller for additional clock
and bus control. Add support for these extensions.
Signed-off-by: tianshuliang <tianshuliang@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports RCA register to sysfs which will help in reading the
disk identification information.
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling the clock, dwmmc exynos driver is trying to access the
register. Then the kernel panic can be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit "mmc: renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of
TMIO own flag" activated MMC_CAP2_NO_WRITE_PROTECT for Renesas SDHI
which incorrectly disabled WP altogether instead of only disabling the
internal mechanism. Since the whole WP handling has been reworked, we
can simply disable this capability to re-enable WP GPIOs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Following up the device tree fixed in commits e78c637127 ("ARM: dts:
rockchip: Fix DWMMC clocks") and ca9eee95a2 ("arm64: dts: rockchip:
Fix DWMMC clocks", 2018-02-15), avoid confusion by using the correct
property name in the debug output if clocks are not found.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable err would be firstly initialized by the return value of
mmc_sd_switch().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we could move card->host->caps & MMC_CAP_4_BIT_DATA
ahead of mmc_sdio_init_uhs_card, in mmc_host_uhs(). So there
we could save this bit to check that. Also, if the process of
sdio_enable_4bit_bus goes wrong, we should bails out early.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.
This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.
Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'num-slots' property had already deprecated.
Remove the 'nom-slots' property that is kept to maintain the compatibility.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'clock-freq-min-max' property had already deprecated.
Remove the 'clock-freq-min-max' property that is kept to maintain
the compatibility.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just applying the existing logic and adding its own characteristics into
the space pointed by an extra entry of struct of_device_id to have support
of MT7622 SoC.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Jumin Li <jumin.li@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However, users also want to
control it from sysfs power/wakeup attribute. That means the driver needs
to check the PM flags before enabling it in the suspend callback. Add
support for that in sdhci-pci, which is the only driver presently using the
MMC_CAP_CD_WAKE flag, and remove the enabling in mmc_gpiod_request_cd_irq()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Do not enable wakeup for SDIO card interrupt unless the SDIO function
driver has requested it which is indicated by mmc_card_wake_sdio_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Do not unnecessarily enable card detect wakeup in the cases that the card
is not removable or a GPIO is used for card detect.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that tuning no longer leaves the Buffer Read Enable bit set (refer
intel_execute_tuning()), glk_cqe_enable() is no longer needed. Get rid of
it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not sure why it was there in the first place, but it's
obviously useless check, so let's remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cur_slot and num_slots has been removed from struct dw_mci in 42f989c002.
Unfortunately, inline documentation was not updated so far.
Fix @lock field documentation in Locking section.
Move @mrq field of struct dw_mci_slot mention closer to it
description, so no one could miss this slightest detail.
Couple of code style fixes as a bonus.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang reports a compile warning:
drivers/mmc/host/dw_mmc.c:2124:5: warning: Value stored to 'prev_state'
is never read
By checking the code, prev_state and state assignment for
STATE_SENDING_CMD is indeed never used after jumping to unlock tag.
So remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the newly added macro to simply to the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO_MASK_CMD is properly enabled in tmio_mmc_start_command().
We have no reason to set it up in tmio_mmc_host_probe(). (If we
really wanted to set it in the probe, we would have to do likewise
when resuming.)
Even worse, the following code is extremely confusing:
_host->sdcard_irq_mask &= ~irq_mask;
The logic is opposite between "->sdcard_irq_mask" and "irq_mask".
The intention is not clear at a glance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, force_pio is cleared when the driver exits. Then, it
resulted in clearing it in multiple places since MMC drivers in
general have multiple exit points.
tmio_mmc_reset_work - bails out on timeout
tmio_process_mrq - error out when it cannot send a command
tmio_mmc_finish_request - successful exit
This is error-prone since we may miss to cover all bail-out points.
To simplify the code, the data structure should be initialized just
before used since we have a single entrance. force_pio is only used
for data transfer, so tmio_mmc_start_data() will be a suitable place
to clear this flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As far as I tested the IP on UniPhier SoCs, TMIO_STAT_{RXRDY,TXRQ}
are asserted for DMA mode as well as for PIO. I need to disable the
those IRQs in dma_ops->start hook, otherwise the DMA transfer fails
with the following error message:
PIO IRQ in DMA mode!
Renesas chips are the same cases since I see their dma_ops->start
hooks explicitly clear TMIO_STAT_{RXRDY,TXRQ} (with nice comment!).
If we do this sanity check in TMIO MMC core, RXRDY/TXRQ handling
should be entirely moved to the core. tmio_mmc_cmd_irq() will
be a suitable place to disable them.
The probe function sets TMIO_MASK_{READOP,WRITEOP} but this is odd.
/* Unmask the IRQs we want to know about */
if (!_host->chan_rx)
irq_mask |= TMIO_MASK_READOP;
if (!_host->chan_tx)
irq_mask |= TMIO_MASK_WRITEOP;
At this point, _host->{chan_rx,chan_tx} are _always_ NULL because
tmio_mmc_request_dma() is called after this code. Consequently,
TMIO_MASK_{READOP,WRITEOP} are set here whether DMA is used or not.
Remove this pointless code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The TMIO mmc cannot detect the card insertion in native_hotplug mode
if the driver is probed without a card inserted.
The reason is obvious; all IRQs are disabled by tmio_mmc_host_probe(),
as follows:
tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL);
The card event IRQs are first enabled by tmio_mmc_start_command() as
follows:
if (!host->native_hotplug)
irq_mask &= ~(TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
tmio_mmc_enable_mmc_irqs(host, irq_mask);
If the driver is probed without a card, tmio_mmc_start_command() is
never called in the first place. So, the card is never detected.
The card event IRQs must be enabled in probe/resume functions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
A card detect GPIO is set up only for platforms with "cd-gpios"
DT property or TMIO_MMC_USE_GPIO_CD flag. However, the driver
core always uses mmc_gpio_get_cd, which just fails with -ENOSYS
if ctx->cd_gpio is unset.
The bit 5 of the status register provides the current signal level
of the CD line. Allow to use it if the GPIO is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The commit 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
and commit 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
made changes, which cause multiply overflow for 32-bit systems. The broken
timeout calculations leads to unexpected ETIMEDOUT errors and causes
stacktrace splat (such as below) during normal data exchange with SD-card.
| Running : 4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1
| - Info: Finished target initialization.
| mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd
| response 0x900, card status 0x0
DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so
code gets compiled on all 32-bit platforms as opposed to usage of
DIV_ROUND_UP when we may only compile stuff on a very few arches.
Lets cast this multiply to u64 type to prevent the overflow.
Fixes: 9d9491a7da ("mmc: dw_mmc: Fix the DTO timeout calculation")
Fixes: 4c2357f57d ("mmc: dw_mmc: Fix the CTO timeout calculation")
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.14
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This property is equivalent to "disable-wp" defined in
Documentation/devicetree/bindings/mmc/mmc.txt
The TMIO MMC core calls mmc_of_parse(), and it sets
MMC_CAP2_NO_WRITE_PROTECT if "disable-wp" property is present.
We do not need a vendor-specific property to do the same thing.
Let's remove the description from the dt-binding to prevent new boards
from using it.
I am keeping the driver code for existing DT files, but added
comments that this is deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The use of this flag has been replaced with MMC_CAP2_NO_WRITE_PROTECT.
No platform defines this flag any more. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
"toshiba,mmc-wrprotect-disable" at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
The flag is propagated as follows:
renesas_sdhi_of_data::capabilities2
-> tmio_mmc_data::capabilities2
-> mmc_host::caps2
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
TMIO_MMC_WRPROTECT_DISABLE at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to set the IODELAY values depending on the various MMC
modes using the pinctrl APIs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i802 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
during the tuning procedure and it has to be disabled during the
tuning procedure Implement workaround for Errata i802 here..
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC tuning procedure is required to support SD card
UHS1-SDR104 mode and EMMC HS200 mode.
SDR104/HS200 DLL Tuning Procedure for AM572x platform is mentioned
in Figure 25-51. SDR104/HS200 DLL Tuning Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
The tuning function sdhci_omap_execute_tuning() will only be
called by the MMC/SD core if the corresponding speed modes
are supported by the OMAP silicon which is set in the mmc
host "caps" field.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UHS-1 DDR50 and MMC DDR52 mode require DDR bit to be
set in the configuration register (MMCHS_CON). Add
sdhci-omap specific set_uhs_signaling ops to set
this bit. Also while setting the UHSMS bit, clock should be
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add card_busy host ops in sdhci_omap to check card busy status.
The voltage switching sequence for AM572x platform is mentioned
in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON
should also be set after switching to 1.8v which is also taken
care in the card_busy ops.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Updating 'power_mode' in sdhci_omap_init_74_clocks results in
'power_mode' never updated to MMC_POWER_OFF during card
removal. This results in initialization sequence not sent to the
card during re-insertion.
Fix it here by adding sdhci_omap_set_power_mode to update power_mode.
This function can also be used later to perform operations that
are specific to a power mode (e.g, disable tuning during power off).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 361c7fe9b0 ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The optional DT parameter max-frequency could init the max bus frequency.
So take care of this, before setting the max bus frequency.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 0a44697627.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jy5l
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
The Meson GX MMC driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h being pulled in by the device.h header
implicitly.
Include the header explicitly to avoid the build failure.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blank help texts are probably either a typo, a Kconfig misunderstanding,
or some kind of half-committing to adding a help text (in which case a
TODO comment would be clearer, if the help text really can't be added
right away).
Best to remove them, IMO.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.
SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.
Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.
These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.
This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.
When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.
dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Tested-by: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
specially highlighted.
First, we have converted the MMC block device from using the legacy blk
interface into using the modern blkmq interface. Not only do we get all the
nice effects from using blkmq, but it also means that new fresh nice code
replaces old rusty code. Great news to everybody that cares about MMC/SD!
It should also be noted that converting to blkmq has not been trivial, mostly
because of that we have been carrying too much of MMC specific optimizations
for the I/O request path, rather than striving to move these to the generic blk
layer. Hopefully we won't be doing that mistake, ever again.
Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro), who both
have been working on this for quite some time!
Second, on top of the blkmq deployment, we have enabled full support the eMMC
command queuing feature, introduced in the eMMC v.5.1 spec. This also includes
an implementation of a host driver library, supporting the corresponding CQHCI
HW. Ideally, those controllers that supports CQHCI should only need some minor
adaptations to make this play.
So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan driver
used on Rockchip RK3399, have enabled support for eMMC command queueing.
Worth to highlight is also that, implementing the eMMC command queuing support
has been a collaborative effort, as several people from Codeaurora, Rockchip,
Intel and Linaro have been involved. However, the work has been driven by
Adrian Hunter (Intel).
In some shadow of the above, here are the rest of the highlights:
MMC core:
- Don't remove non-removable cards during system suspend
- Add a slot-gpio helper to check capability of GPIO WP detection
MMC host:
- sdhci: Cleanups and improvements of some wakeup related code
- sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
- sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
- sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
- sdhci_f_sdh30: Add ACPI support
- sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
- sdhci-of-esdhc: A few minor fixes
- mmci: Add support for new STM32 variant
- renesas_sdhi: enable R-Car D3 (r8a77995) support
- tmio/renesas_sdhi: Re-structuring, cleanups and modernizations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kUV+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"There are two major achievements for MMC in this release, which
deserves to be specially highlighted.
First, we have converted the MMC block device from using the legacy
blk interface into using the modern blkmq interface. Not only do we
get all the nice effects from using blkmq, but it also means that new
fresh nice code replaces old rusty code. Great news to everybody that
cares about MMC/SD!
It should also be noted that converting to blkmq has not been trivial,
mostly because of that we have been carrying too much of MMC specific
optimizations for the I/O request path, rather than striving to move
these to the generic blk layer. Hopefully we won't be doing that
mistake, ever again.
Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro),
who both have been working on this for quite some time!
Second, on top of the blkmq deployment, we have enabled full support
the eMMC command queuing feature, introduced in the eMMC v.5.1 spec.
This also includes an implementation of a host driver library,
supporting the corresponding CQHCI HW. Ideally, those controllers that
supports CQHCI should only need some minor adaptations to make this
play.
So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan
driver used on Rockchip RK3399, have enabled support for eMMC command
queueing.
Worth to highlight is also that, implementing the eMMC command queuing
support has been a collaborative effort, as several people from
Codeaurora, Rockchip, Intel and Linaro have been involved. However,
the work has been driven by Adrian Hunter (Intel).
In some shadow of the above, here are the rest of the highlights:
MMC core:
- Don't remove non-removable cards during system suspend
- Add a slot-gpio helper to check capability of GPIO WP detection
MMC host:
- sdhci: Cleanups and improvements of some wakeup related code
- sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
- sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
- sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
- sdhci_f_sdh30: Add ACPI support
- sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
- sdhci-of-esdhc: A few minor fixes
- mmci: Add support for new STM32 variant
- renesas_sdhi: enable R-Car D3 (r8a77995) support
- tmio/renesas_sdhi: Re-structuring, cleanups and modernizations"
* tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (96 commits)
mmc: mmci: fix error return code in mmci_probe()
mmc: davinci: suppress error message on EPROBE_DEFER
mmc: davinci: dont' use module_platform_driver_probe()
mmc: tmio: hide unused tmio_mmc_clk_disable/tmio_mmc_clk_enable functions
mmc: mmci: Add STM32 variant
mmc: mmci: Add support for setting pad type via pinctrl
mmc: mmci: Don't pretend all variants to have OPENDRAIN bit
mmc: mmci: Don't pretend all variants to have MCI_STARBITERR flag
mmc: mmci: Don't pretend all variants to have MMCIMASK1 register
mmc: tmio: refactor .get_ro hook
mmc: slot-gpio: add a helper to check capability of GPIO WP detection
mmc: tmio: remove dma_ops from tmio_mmc_host_probe() argument
mmc: tmio: move {tmio_}mmc_of_parse() to tmio_mmc_host_alloc()
mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()
mmc: tmio: ioremap memory resource in tmio_mmc_host_alloc()
mmc: sh_mmcif: remove redundant initialization of 'opc'
mmc: sdhci: Rework sdhci_enable_irq_wakeups()
mmc: sdhci: Handle failure of enable_irq_wake()
mmc: sdhci: Stop exporting sdhci_enable_irq_wakeups()
mmc: sdhci-pci: Use device wakeup capability to determine MMC_PM_WAKE_SDIO_IRQ capability
...
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f9bb304ce8 ("mmc: mmci: Add support for setting pad type via pinctrl")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This suppresses printing an error message during probe of the TI DaVinci
MMC driver when the error is EPROBE_DEFER.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This changes module_platform_driver_probe() to module_platform_driver()
in the TI DaVinci MMC driver.
On device tree systems, we can get a -EPROBE_DEFER when using a pinmux
for the CD GPIO, which results in the driver never loading because
module_platform_driver_probe() prevents it from being re-probed.
So, we replace module_platform_driver_probe() with
module_platform_driver() and removed the __init attributes accordingly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_PM is disabled, we get a warning about the clock handling
being unused:
drivers/mmc/host/tmio_mmc_core.c:937:13: error: 'tmio_mmc_clk_disable' defined but not used [-Werror=unused-function]
static void tmio_mmc_clk_disable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/tmio_mmc_core.c:929:12: error: 'tmio_mmc_clk_enable' defined but not used [-Werror=unused-function]
static int tmio_mmc_clk_enable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~
As the clock handling is now done elsewhere, this is only used when
power management is enabled. We could make the functions as __maybe_unused,
but since there is already an #ifdef section, it seems easier to move
the helpers closer to their callers.
Fixes: b21fc29438 ("mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STM32F4 and STM32F7 MCUs has a SDIO controller that looks like
an ARM PL810.
This patch adds the STM32 variant so that mmci driver supports it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If variant hasn't the control bit to switch pads in opendrain mode,
we can achieve the same result by asking to the pinmux driver to
configure pins for us.
This patch make the mmci driver able to do this whenever needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for supporting STM32 variant which doesn't
have opendrain bit in MMCIPOWER register.
ST others variant (u300, nomadik and ux500) uses MCI_OD bit whereas
others variants uses MCI_ROD bit.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for supporting the STM32 variant that
has no such bit in the status register.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two mask registers are used in order to select which events have to
actually generate an interrupt on each IRQ line.
It seems that in the single-IRQ case it's assumed that the IRQs lines
are simply OR-ed, while the two mask registers are still present. The
driver still programs the two mask registers separately.
However the STM32 variant has only one IRQ, and also has only one mask
register.
This patch prepares for STM32 variant support by making the driver using
only one mask register.
This patch also optimize the MMCIMASK1 mask usage by caching it into
host->mask1_reg which avoid to read it into mmci_irq().
Tested only on STM32 variant. RFT for variants other than STM32
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This IP provides the write protect signal level in the status
register, but it is also possible to use GPIO for WP. They are
exclusive, so it is not efficient to call mmc_gpio_get_ro() every
time from tmio_mmc_get_ro() if we know gpio_ro is not used.
Check the capability of gpio_ro just once in the probe function,
then set mmc_gpio_get_ro to .get_ro if it is the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers need to set up various struct members for tmio_mmc_host before
calling tmio_mmc_host_probe(). Do likewise for host->dma_ops instead
of passing it as a function argument.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() parses various DT properties and sets capability flags
accordingly. However, drivers have no chance to run platform init
code depending on such flags because mmc_of_parse() is called from
tmio_mmc_host_probe().
Move mmc_of_parse() to tmio_mmc_host_alloc() so that drivers can
handle capabilities before mmc_add_host(). Move tmio_mmc_of_parse()
likewise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock is enabled in the tmio_mmc_host_probe(). It also prevents
drivers from performing platform-specific settings before mmc_add_host()
because the register access generally requires a clock.
Enable/disable the clock in drivers' probe/remove. Also, I passed
tmio_mmc_data to tmio_mmc_host_alloc() because renesas_sdhi_clk_enable()
needs it to get the private data from tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register region is ioremap'ed in the tmio_mmc_host_probe(), i.e.
drivers cannot get access to the hardware before mmc_add_host().
Actually, renesas_sdhi_core.c reads out the CTL_VERSION register to
complete the platform-specific settings. However, at this point,
the MMC host is already running.
Move the register ioremap to tmio_mmc_host_alloc() so that drivers
can perform platform-specific settings between tmio_mmc_host_alloc()
and tmio_mmc_host_probe().
I changed tmio_mmc_host_alloc() to return an error pointer to
propagate the return code from devm_ioremap_resource().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable opc is initialized with a value that is never read, opc
is later re-assigned a newer value, hence the initialization can
be removed.
Cleans up clang warning:
drivers/mmc/host/sh_mmcif.c:919:6: warning: Value stored to 'opc'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding more conditions for whether IRQ wakeup is
enabled, rework sdhci_enable_irq_wakeups() so that needed bits are added
instead of adding them all and then removing the unneeded bits.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_enable_irq_wakeups() is a local function, change it to
return whether the IRQ wakeup was successfully enabled. This is in
preparation for adding more conditions for whether IRQ wakeup is enabled.
Note it is assumed, for SDHCI devices, that suspend is more important than
wakeup, so we continue to suspend regardless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that it is not being used by any drivers, stop exporting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PCI and ACPI determine if a device is wakeup capable, so use that to
determine the MMC_PM_WAKE_SDIO_IRQ capability correctly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_enable_irq_wakeups() is already called by sdhci_suspend_host() so
sdhci-pci should not need to call it. However sdhci_suspend_host() only
calls it if wakeups are enabled, and sdhci-pci does not enable them until
after calling sdhci_suspend_host(). So move the calls to
sdhci_pci_init_wakeup() before calling sdhci_suspend_host(), and
stop calling sdhci_enable_irq_wakeups(). That results in some
simplification because sdhci_pci_suspend_host() and
__sdhci_pci_suspend_host() no longer need to be separate functions.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CQHCI initialization and implement CQHCI operations for Arasan
SDHCI variant host, namely arasan,sdhci-5.1, which is used by Rockchip
RK3399 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.
This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[ 1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[ 2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[ 12.645056] mmc1: Timeout waiting for hardware interrupt.
[ 12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 12.656921] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001201
[ 12.663366] mmc1: sdhci: Blk size: 0x00000004 | Blk cnt: 0x00000000
[ 12.669813] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
[ 12.676258] mmc1: sdhci: Present: 0x01f8028f | Host ctl: 0x00000013
[ 12.682703] mmc1: sdhci: Power: 0x00000002 | Blk gap: 0x00000000
[ 12.689148] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000003f
[ 12.695594] mmc1: sdhci: Timeout: 0x0000008e | Int stat: 0x00000000
[ 12.702039] mmc1: sdhci: Int enab: 0x107f004b | Sig enab: 0x107f004b
[ 12.708485] mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00001201
[ 12.714930] mmc1: sdhci: Caps: 0x07eb0000 | Caps_1: 0x08100810
[ 12.721375] mmc1: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000
[ 12.727821] mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000
[ 12.734265] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[ 12.745157] mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0xc8049200
[ 12.751601] mmc1: sdhci: ============================================
[ 12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[ 12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[ 12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[ 12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[ 12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Wladimir J. van der Laan <laanwj@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To use a GPIO line for card detection, TMIO_MMC_USE_GPIO_CD is set
by a legacy board (arch/sh/boards/mach-ecovec24).
For DT platforms, the "cd-gpios" property is a legitimate way for that
in case the IP-builtin card detection can not be used for some reason.
mmc_of_parse() calls mmc_gpiod_request_cd() to set up ctx->cd_gpio if
the "cd-gpios" property is specified.
To cater to both cases, mmc_can_gpio_cd() is a correct way to check
which card detection logic is used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Intel Edison the Broadcom Wi-Fi card, which is connected to SDIO,
requires 2.0v, while the host, according to Intel Merrifield TRM,
supports 1.8v supply only.
The card announces itself as
mmc2: new ultra high speed DDR50 SDIO card at address 0001
Introduce a custom OCR mask for SDIO host controller on Intel Merrifield
and add a special case to sdhci_set_power_noreg() to override 2.0v supply
by enforcing 1.8v power choice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The inconsistent NULL checking in this function causes static checker
warnings.
drivers/mmc/host/renesas_sdhi_sys_dmac.c:360 renesas_sdhi_sys_dmac_issue_tasklet_fn()
error: we previously assumed 'host' could be null (see line 351)
On reviewing this code, "host" can't ever be NULL so we can just remove
the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Fujitsu SDH30 SDHCI controller may be described as a SCX0002 ACPI
device on ACPI platforms incorporating the Socionext SynQuacer SoC.
Given that mmc_of_parse() has already been made ACPI/DT agnostic,
making the SDH30 driver ACPI capable is actually rather simple:
all we need to do is make the call to sdhci_get_of_property() [which
does not set any properties we care about] and the clock handling
dependent on whether we are dealing with a DT device, and exposing
the ACPI id via the platform_driver struct and the module metadata.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc clock can be stopped during runtime suspend and restart during runtime
resume if the sdio irq is not enabled. Stop sdio clock reduce EMI of
the device when the bus is not in use.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
runtime_resume() should re-enable the clocks in reverse order comparing with
runtime_suspend()
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to return in case of error even if the actual implementation
of sdhci_runtime_suspend_host always return 0. We don't want to
power down the clock and the assuption is that the sdhci_runtime_suspend_host
always let the system consistent in case of failure
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Arasan Controller is based on a FPGA platform and has integrated phy
with specific registers used during initialization and
management of different modes. The phy and the controller are integrated
and registers are very specific to Arasan.
Arasan being an IP provider, licenses these IPs to various companies for
integration of IP in custom SOCs. The custom SOCs define own register
map depending on how bits are tied inside the SOC for phy registers,
depending on SOC memory plan and hence will require own platform drivers.
If more details on phy registers are required, an interface document is
hosted at https://arasan.com/NF/eMMC5.1 PHY Programming in Linux.pdf.
Signed-off-by: Atul Garg <agarg@arasan.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The global array clashes with a newly added symbol of the same name:
drivers/staging/ccree/cc_debugfs.o:(.data+0x0): multiple definition of `debug_regs'
drivers/mmc/host/s3cmci.o:(.data+0x70): first defined here
We should fix both, this one addresses the s3cmci driver by removing
the symbol from the global namespace. While at it, this separates
the declaration from the type definition and makes the variable const.
Fixes: 9bdd203b4d ("s3cmci: add debugfs support for examining driver and hardware state")
Fixes: b3ec9a6736 ("staging: ccree: staging: ccree: replace sysfs by debugfs interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because we started using io*_rep accessors previously because they are
more widely defined across architectures, let's be consistent and use
this family for all accessor wrappers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to SD spec 3.00 3.6.1 signal voltage switch
procedure step 6~8,
(6) Set 1.8V Signal Enable in the Host Control 2 register.
(7) Wait 5ms. 1.8V voltage regulator shall be stable within this period.
(8) If 1.8V Signal Enable is cleared by Host Controller, go to step (12).
Host should wait 5ms after set 1.8V signal enable bit in
Host Control 2 register and check if 1.8V is stable or not.
But current code checks this bit right after set it.
On some platforms with xenon controller found the bit is
cleared right away and host reports "1.8V regulator output
did not became stable" and 5ms delay can help.
Implement voltage_switch callback for xenon controller to add 5ms
delay to make sure the 1.8V signal enable bit is set by controller.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sane values for bus_shift are:
0 - for 16 bit bus
1 - for 32 bit bus
2 - for 64 bit bus
"unsigned long" is too much.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_host has "scc_tappos", but in fact, it is Renesas
private data. Move it to renesas_sdhi.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_host has "dma_dataend" and "dma_complete", but in fact,
they are Renesas private data. Move them to renesas_sdhi.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct tmio_mmc_dma looks like TMIO core data, but in fact, Renesas
private data. Move it to renesas_sdhi.h (probably, it is better to
rename it to renesas_sdhi_dma, or squash it into struct renesas_sdhi).
I also moved struct renesas_sdhi and host_to_priv() to that header
because they are necessary to convert the tmio_mmc_host pointer into
the renesas_sdhi pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC_DRV_OP_GET_EXT_CSD request completes successfully, then
ext_csd must be freed, but in one case it was not. Fix that.
Signed-off-by: Liu Changcheng <changcheng.liu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers do not need to call mmc_gpiod_request_cd_irq() explicitly
because mmc_start_host() calls it. To make it work, cd_gpio must
be set before mmc_add_host().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers can set any mmc_host_ops hooks between tmio_mmc_host_alloc()
and tmio_mmc_host_probe(). Remove duplicated hooks in tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, tmio_mmc_ops is static data and tmio_mmc_host_probe()
updates some hooks in the static data. This is a problem when
two or more instances call tmio_mmc_host_probe() and each of them
requests to use its own card_busy/start_signal_voltage_switch.
We can borrow a solution from sdhci_alloc_host(). Copy the whole
ops structure to host->mmc_host_ops, then override the hooks in
malloc'ed data. Constify tmio_mmc_ops since it is now a template
ops used by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TMIO core misses to call request_mem_region().
devm_ioremap_resource() takes care of it and makes the code cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The remove, suspend, resume hooks need to get tmio_mmc_host. It is
tedious to call mmc_priv() to convert mmc_host to tmio_mmc_host.
We can directly set tmio_mmc_host to driver data.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ARCH_RENESAS is a stronger condition than (ARM || ARM64).
If ARCH_RENESAS is enabled, (ARM || ARM64) is met as well.
What is worse, the first depends on line prevents COMPILE_TEST from
enabling this driver. It should be removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all archs define reads* and writes*. Switch to ioread*_rep and
friends which is defined everywhere, so we can enable COMPILE_TEST after
that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following error occurs when loading renesas_sdhi_core.c module,
so add MODULE_LICENSE("GPL v2").
renesas_sdhi_core: module license 'unspecified' taints kernel.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Fixes: 9d08428afb ("mmc: renesas-sdhi: make renesas_sdhi_sys_dmac main module file")
Cc: <stable@vger.kernel.org> # v4.13+
[Shimoda: Added Fixes tag and Cc to the stable ML]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The description in the Makefile is odd. Fix the CONFIG selection
in a cleaner way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel DSM function 8 has been used to identify transfer modes that are not
working on some CHT boards. Add support for that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a ->setup_host() callback so that device-specific changes can be made
to the mmc host controller before it is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL. The callers are not expecting that and will have a NULL pointer
dereference.
Fixes: 41e3efd07d ("mmc: block: Simplify cleaning up the queue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Absence of parentheses is not affecting current code, but ensure macro
parameters are wrapped in parentheses.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.
Fixes: 9d4579a85c ("mmc: mmc_test: Disable Command Queue while mmc_test is used")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
Commands during non-blocking read - use Set Block Count (CMD23)
Commands during non-blocking write - use Set Block Count (CMD23)
mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().
Fixes: cb39f61e9b ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch supports HS400 for AMD upcoming emmc 5.0 controller.The
HS400 and HS200 mode requires hardware work around also. This patch
adds the quirks for the same.
Signed-off-by: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The power register needs to have a valid voltage set
even when the power supply is managed by an external regulator.
Signed-off-by: Milan Stevanovic <milan.o.stevanovic@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function mmc_cqe_issue_type is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/mmc/core/queue.c:62:21: warning: symbol 'mmc_cqe_issue_type'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/core/block.c:2106:9-10: WARNING: return of 0/1 in function 'mmc_blk_status_error' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes:7eb43d537166 ("mmc: block: blk-mq: Stop using legacy recovery")
CC: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver's blk-mq paths do not use mmc_start_areq(). In order to
remove mmc_start_areq() entirely, start by removing it from mmc_test.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
There are only a few things the recovery needs to do. Primarily, it just
needs to:
Determine the number of bytes transferred
Get the card back to transfer state
Determine whether to retry
There are also a couple of additional features:
Reset the card before the last retry
Read one sector at a time
The legacy code spent much effort analyzing command errors, but commands
fail fast, so it is simpler just to give all command errors the same number
of retries.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Set a 10 second timeout for polling write request busy state. Note, mmc
core is setting a 3 second timeout for SD cards, and SDHCI has long had a
10 second software timer to timeout the whole request, so 10 seconds should
be ample.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
According to the specification, total access time is derived from both TAAC
and NSAC, which means the timeout should add both timeout_ns and
timeout_clks. Host drivers do that, so make the block driver do that too.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
The card is required to return to transfer state. Since that is the state
required to start another transfer, check for that state instead of
programming state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Pedantically, ensure the status is checked for the last time after the full
timeout has passed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Check error bits and save the exception bit when polling card busy.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make card_busy_detect() accumulate all response error bits. Later patches
will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Recovery is simpler to understand if it is only used for errors. Create a
separate function for card polling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
For blk-mq, add support for completing requests directly in the ->done
callback. That means that error handling and urgent background operations
must be handled by recovery_work in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds CMDQ support for command-queue compatible
hosts.
Command queue is added in eMMC-5.1 specification. This
enables the controller to process upto 32 requests at
a time.
Adrian Hunter contributed renaming to cqhci, recovery, suspend
and resume, cqhci_off, cqhci_wait_for_idle, and external timeout
handling.
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Add CQE support to the block driver, including:
- optionally using DCMD for flush requests
- "manually" issuing discard requests
- issuing read / write requests to the CQE
- supporting block-layer timeouts
- handling recovery
- supporting re-tuning
CQE offers 25% - 50% better random multi-threaded I/O. There is a slight
(e.g. 2%) drop in sequential read speed but no observable change to sequential
write.
CQE automatically sends the commands to complete requests. However it only
supports reads / writes and so-called "direct commands" (DCMD). Furthermore
DCMD is limited to one command at a time, but discards require 3 commands.
That makes issuing discards through CQE very awkward, but some CQE's don't
support DCMD anyway. So for discards, the existing non-CQE approach is
taken, where the mmc core code issues the 3 commands one at a time i.e.
mmc_erase(). Where DCMD is used, is for issuing flushes.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Define and use a blk-mq queue. Discards and flushes are processed
synchronously, but reads and writes asynchronously. In order to support
slow DMA unmapping, DMA unmapping is not done until after the next request
is started. That means the request is not completed until then. If there is
no next request then the completion is done by queued work.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Add error-handling comments to explain what would also be done for blk-mq
if it used the legacy error-handling.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Make mmc_pre_req() and mmc_post_req() available to the card drivers. Later
patches will make use of this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Use blk_cleanup_queue() to shutdown the queue when the driver is removed,
and instead get an extra reference to the queue to prevent the queue being
freed before the final mmc_blk_put().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
mmc_cleanup_queue() is not used by a different module. Do not export it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
It had an U+FFFD: not a corrupted character but a literal well-formed
replacement marker.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a few udelay() left which are in a range that they should be
usleep_range() these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Documentation/timers/timers-howto.txt recommends to use usleep_range for
delays 1-20ms. Let's adhere to it. No need for messing with HZ and still
do busy looping these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not efficient to call gpiod_to_irq() regardless the flag, then
ignore the returned irq if MMC_CAP_NEEDS_POLL.
Move gpiod_to_irq() after the MMC_CAP_NEEDS_POLL check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the latest version of parsing the new eMMC bindings was moved from
core.c to mmc.c, it was overlooked that drv_type could be used
uninitialized. Fix it!
Fixes: 6186d06c51 ("mmc: parse new binding for eMMC fixed driver type")
Reported-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=13VJ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Ensure that debugfs files are removed properly
- Fix missing blk_put_request()
- Deal with errors from blk_get_request()
- Rewind mmc bus suspend operations at failures
- Prepend '0x' to ocr and pre_eol_info in sysfs to identify as hex
MMC host:
- sdhci-msm: Make it optional to wait for signal level changes
- sdhci: Avoid swiotlb buffer being full"
* tag 'mmc-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: prepend 0x to OCR entry in sysfs
mmc: core: prepend 0x to pre_eol_info entry in sysfs
mmc: sdhci: Avoid swiotlb buffer being full
mmc: sdhci-msm: Optionally wait for signal level changes
mmc: block: Ensure that debugfs files are removed
mmc: core: Do not leave the block driver in a suspended state
mmc: block: Check return value of blk_get_request()
mmc: block: Fix missing blk_put_request()
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The sysfs entry "ocr" was missing the 0x prefix to identify it as hex
formatted.
Fixes: 5fb06af7a3 ("mmc: core: Extend sysfs with OCR register")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.8+
[Ulf: Amended change to also cover SD-cards]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sysfs entry "pre_eol_info" was missing the 0x prefix to identify it
as hex formatted.
Fixes: 46bc5c408e ("mmc: core: Export device lifetime information through sysfs")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit de3ee99b09 ("mmc: Delete bounce buffer handling") deletes the
bounce buffer handling, but also causes the max_req_size for sdhci to be
increased, in case when max_segs == 1. This causes errors for sdhci-pci
Ricoh variant, about the swiotlb buffer to become full.
Fix the issue, by taking IO_TLB_SEGSIZE and IO_TLB_SHIFT into account when
deciding the max_req_size for sdhci.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Not all instances of the SDCC core supports changing signal voltage and
as such will not generate a power interrupt when the software attempts
to change the voltage. This results in probing the eMMC on some devices
to take over 2 minutes.
Check that the SWITCHABLE_SIGNALING_VOLTAGE bit in MCI_GENERICS is set
before waiting for the power interrupt.
Cc: Sahitya Tummala <stummala@codeaurora.org>
Cc: Vijay Viswanath <vviswana@codeaurora.org>
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card is not necessarily being removed, but the debugfs files must be
removed when the driver is removed, otherwise they will continue to exist
after unbinding the card from the driver. e.g.
# echo "mmc1:0001" > /sys/bus/mmc/drivers/mmcblk/unbind
# cat /sys/kernel/debug/mmc1/mmc1\:0001/ext_csd
[ 173.634584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
[ 173.643356] IP: mmc_ext_csd_open+0x5e/0x170
A complication is that the debugfs_root may have already been removed, so
check for that too.
Fixes: 627c3ccfb4 ("mmc: debugfs: Move block debugfs into block module")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver must be resumed if the mmc bus fails to suspend the card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
The Socionext SynQuacer SoC inherits this IP from Fujitsu, but
requires the F_SDH30_CMD_DAT_DELAY bit to be set in the
F_SDH30_ESD_CONTROL control register. So set this bit if the
DT node has the 'fujitsu,cmd-dat-delay-select' property.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As documented in Documentation/timers/timers-howto.txt
as follows, replace msleep() with usleep_range().
msleep(1~20) may not do what the caller intends, and
will often sleep longer (~20 ms actual sleep for any
value given in the 1~20ms range). In many cases this
is not the desired behavior.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent CTO timer introduced in commit 03de19212e ("mmc: dw_mmc:
introduce timer for broken command transfer over scheme") was causing
observable problems due to race conditions. Previous patches have
fixed those race conditions.
It can be observed that these same race conditions ought to be
theoretically possible with the DTO timer too though they are
massively less likely to happen because the data timeout is always set
to 0xffffff right now. That means even at a 200 MHz card clock we
were arming the DTO timer for 94 ms:
>>> (0xffffff * 1000. / 200000000) + 10
93.886075
We always also were setting the DTO timer _after_ starting the
transfer, unlike how the old code was seting the CTO timer.
In any case, even though the DTO timer is much less likely to have
races, it still makes sense to add code to handle it _just in case_.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a jump target so that a specific string copy operation is stored
only once at the end of this function implementation.
Replace two calls of the function "strncpy" by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Add a jump target so that a bit of exception handling can be better
reused at the end of this function.
* Adjust condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Allen <allen.lkml@gmail.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel host controllers use an ACPI device-specific method to ensure
correct voltage switching. Fix voltage switch for those, by adding a call
to the DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_acpi_slot structure, then sdhci_acpi_probe() will allocate extra
space for it, and sdhci_acpi_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
data lines have applied to perfer to use rise edge, also need
apply it to cmd line.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enlarge outstanding value to improve read performance
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
some platform(eg.mt2701) does not support "stop clk fix", in
this case, need set correct latch-ck to avoid crc error caused
by stop clock block-internally.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
source clock need an independent cg to control, when doing clk mode
switch, need gate source clock to avoid hw issue(multi-bit sync hw hang)
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2712 supports stop_clk fix and enhance_rx, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bit7 of PATCH_BIT1 has different meaning in new design, to
compatible with previous platform, clear this bit in new
platform.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 supports async fifo & data tune, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
from mt2701, the register of PAD_TUNE has been phased out,
while there is a new register of PAD_TUNE0
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the origin design of hs400_tune_response is for mt8173 because of
mt8173 has a special design. for doing that, we add a new member
"compatible", by now it's only for mt8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like the CTO timeout calculation introduced recently, the DTO
timeout calculation was incorrect. It used "bus_hz" but, as far as I
can tell, it's supposed to use the card clock. Let's account for the
div value, which is documented as 2x the value stored in the register,
or 1 if the register is 0.
NOTE: This was likely not terribly important until commit 16a34574c6
("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is
documented on Rockchip SoCs (the ones that used to define the quirk)
to always be 0 or 1. ...and, in fact, it's documented to only be 1
with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to
everyone it was mostly OK to ignore the DIV value.
I haven't personally observed any problems that are fixed by this
patch but I also haven't tested this anywhere with a DIV other an 0.
AKA: this problem was found simply by code inspection and I have no
failing test cases that are fixed by it. Presumably this could fix
real bugs for someone out there, though.
Fixes: 16a34574c6 ("mmc: dw_mmc: remove the quirks flags")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This attempts to instill a bit of paranoia to the code dealing with
the CTO timer. It's believed that this will make the CTO timer more
robust in the case that we're having very long interrupt latencies.
Note that I originally thought that perhaps this patch was being
overly paranoid and wasn't really needed, but then while I was running
mmc_test on an rk3399 board I saw one instance of the message:
dwmmc_rockchip fe320000.dwmmc: Unexpected interrupt latency
I had debug prints in the CTO timer code and I found that it was
running CMD 13 at the time.
...so even though this patch seems like it might be overly paranoid,
maybe it really isn't?
Presumably the bad interrupt latency experienced was due to the fact
that I had serial console enabled as serial console is typically where
I place blame when I see absurdly large interrupt latencies. In this
particular case there was an (unrelated) printout to the serial
console just before I saw the "Unexpected interrupt latency" printout.
...and actually, I managed to even reproduce the problems by running
"iw mlan0 scan > /dev/null" while mmc_test was running. That not only
does a bunch of PCIe traffic but it also (on my system) outputs some
SELinux log spam.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the commit 03de19212e ("mmc: dw_mmc: introduce timer for broken
command transfer over scheme") we tried to calculate the expected
hardware command timeout value. Unfortunately that calculation isn't
quite correct in all cases. It used "bus_hz" but, as far as I can
tell, it's supposed to use the card clock. Let's account for the div
value, which is documented as 2x the value stored in the register, or
1 if the register is 0.
NOTE: It's not expected that this will actually fix anything important
since the 10 ms margin added by the function will pretty much dwarf
any calculations. The card clock should be 100 kHz at minimum and:
1000 ms/s * (255 * 2) / 100000 Hz.
Gives us 5.1 ms.
...so really the point of this patch is just to make the code more
"correct" in case anyone ever tries to remove the 10 ms buffer.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running with the commit 03de19212e ("mmc: dw_mmc: introduce
timer for broken command transfer over scheme") I found this message
in the log:
Unexpected command timeout, state 7
It turns out that we weren't properly cancelling the new CTO timer in
the case that a voltage switch was done. Let's promote the cancel
into the dw_mci_cmd_interrupt() function to fix this.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 has 12bit clock div, which is not compatible with
mt8135/mt8173. and, some additional features will be added in
mt2701/mt2712, so that need distinguish it by comatibale name.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We keep PCI Ids in sdhci-pci.h and the O2-specific definitions belong in
sdhci-pci-o2micro.c. Move those definitions accordingly. Remove unused O2
definitions in sdhci-pci-core.c. The 3 o2micro external function
declarations might as well be in sdhci-pci.h as well, so move them there
and get rid of sdhci-pci-o2micro.h entirely.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy Intel slot probe functions into one. A single function can be used
because the logic uses hid / uid as necessary to identify devices anyway.
This gets rid of some pointless comments and checks for variables that
cannot possibly be NULL, as well as giving the function a name that
identifies it as specific to Intel controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of acpi_device_uid() instead of open coding.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement fallback compatibility strings for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also, improve readability by listing the shmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Parse the new binding and store it in the host struct after doing some
sanity checks. The code is designed to support fixed SD driver type if
we ever need that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Especially, make clear what the return value means.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accessing register fields generally need mask and shift part.
Defining them separately, like SDHCI_CDNS_HRS06_TUNE_{SHIFT,MASK},
is tedious.
Register fields can be always defined by GENMASK (or, BIT if it it
a single bit). They are nicely handled by FIELD_* macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using PTR_ERR_OR_ZERO() instead of IS_ERR() works, but it's not how
you're supposed to write these conditions.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This has a copy and paste bug so we use "host->fixed_factor_clk" which
is a valid pointer instead of "host->cfg_div_clk" which holds the error
code.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The __WARN_printf() function is not portable across architectures
and causes a compile-time error on x86 and others that don't use
the asm-generic version of asm/bug.h:
drivers/mmc/host/sdhci-msm.c: In function 'sdhci_msm_check_power_status':
drivers/mmc/host/sdhci-msm.c:1066:4: error: implicit declaration of function '__WARN_printf'; did you mean '__dev_printk'? [-Werror=implicit-function-declaration]
__WARN_printf("%s: pwr_irq for req: (%d) timed out\n",
^~~~~~~~~~~~~
The change that introduced this error, "mmc: sdhci-msm: Add sdhci msm
register write APIs which wait for pwr irq", likely meant to use
dev_warn(), so I'm changing over to that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_regulator_get_supply returns -EPROBE_DEFER if either vmmc or
vqmmc regulators had their probing deferred.
vqmmc regulator is needed by UHS to work properly, therefore this
patch checks the value returned by mmc_regulator_get_supply to
make sure we have a reference to both vmmc and vqmmc (if found in
the DT).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This error message can go because a) currently nothing else than
EPROBE_DEFER is returned and b) if this is going to change a much more
detailed error message should come from mmc_regulator_get_supply()
anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a driver for the SDIO/MMC host found on the Amlogic Meson SoCs. This
is an MMC controller which provides an interface between the application
processor and various memory cards. It supports the SD specification
v2.0 and the eMMC specification v4.41.
The controller provides an internal "mux" which allows connecting up to
three MMC devices to it. Only one device can be used at a time though
since the registers are shared across all devices. The driver takes care
of synchronizing access (similar to the dw_mmc driver).
The maximum supported bus-width is 4-bits.
Amlogic's GPL kernel sources call the corresponding driver "aml_sdio" to
differentiate it from the other MMC controller in (at least the Meson8
and Meson8b) the SoCs (they call the other drivers aml_sdhc and
aml_sdhc_m8, which seem to support a bus-width of up to 8-bits). This
means that there are three different MMC host controller IP blocks from
Amlogic (each of them with completely own register layout and features):
- "SDIO": 1 and 4 bit bus width, support for high-speed modes up to
UHS-I SDR50, part of Meson6, Meson8 and Meson8b (the driver from this
patch targets this controller)
- "SDHC": 1, 4 and 8 bit bus width, compatible with standard iNAND
interface, support for speeds up to HS200 and MMC spec up to version
4.5x, part of Meson8 and Meson8b SoCs (there is no mainline driver
for this controller yet)
- "SDEMMC": 1, 4 and 8 bit bus width, support for speeds up to HS400
and MMC spec up to version 5.0, part of the Meson GX (64-bit) SoCs
(supported by the meson-gx MMC host driver)
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function sdhci_at91_set_uhs_signaling is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'sdhci_at91_set_uhs_signaling' was not declared. Should it be
static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The array hs_timing_cfg is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warning:
symbol 'hs_timing_cfg' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support for non-dt based initialization for Exynos SoCs has been removed,
so there is no need to keep driver IDs for this case. While touching this,
replace odd conditional code for instantiating driver data for Exynos4
SoCs with a simple reference and move that driver data under CONFIG_OF.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Without the ThunderX/OcteonTx GPIO driver the MMC driver
would not power up any MMC devices. Therefore add a
dependency to the GPIO driver and remove the unneeded GPIOLIB
dependency.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Register writes which change voltage of IO lines or turn the IO bus
on/off require controller to be ready before progressing further. When
the controller is ready, it will generate a power irq which needs to be
handled. The thread which initiated the register write should wait for
power irq to complete. This will be done through the new sdhc msm write
APIs which will check whether the particular write can trigger a power
irq and wait for it with a timeout if it is expected.
The SDHC core power control IRQ gets triggered when -
* There is a state change in power control bit (bit 0)
of SDHCI_POWER_CONTROL register.
* There is a state change in 1.8V enable bit (bit 3) of
SDHCI_HOST_CONTROL2 register.
* Bit 1 of SDHCI_SOFTWARE_RESET is set.
Also add support APIs which are used by sdhc msm write APIs to check
if power irq is expected to be generated and wait for the power irq
to come and complete if the irq is expected.
This patch requires CONFIG_MMC_SDHCI_IO_ACCESSORS to be enabled.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable CONFIG_MMC_SDHCI_IO_ACCESSORS so that SDHC controller specific
register read and write APIs, if registered, can be used.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a rare scenario in HW, where the first clear pulse could
be lost when the actual reset and clear/read of status register
are happening at the same time. Fix this by retrying upto 10 times
to ensure the status register gets cleared. Otherwise, this will
lead to a spurious power IRQ which results in system instability.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC controller reset (SW_RST) during probe may trigger power irq if
previous status of PWRCTL was either BUS_ON or IO_HIGH_V. So before we
enable the power irq interrupt in GIC (by registering the interrupt
handler), we need to ensure that any pending power irq interrupt status
is acknowledged otherwise power irq interrupt handler would be fired
prematurely.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. However there are various circumstances when a card
might be re-initialized, such as after system resume, warm re-boot, or
error handling. However, a UHS card will continue to use 1.8V signaling
unless it is power cycled.
If the card has not been power cycled, it may still be using 1.8V
signaling. According to the SD spec., the Bus Speed Mode (function group 1)
bits 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
they can be used to determine if the card has already switched to 1.8V
signaling. Detect that situation and try to initialize a UHS-I (1.8V)
transfer mode.
Tested with the following cards:
Transcend 4GB High Speed
Kingston 64GB SDR104
Lexar by Micron HIGH-PERFORMANCE 300x 16GB DDR50
SanDisk Ultra 8GB DDR50
Transcend Ultimate 600x 16GB SDR104
Transcend Premium 300x 64GB SDR104
Lexar by Micron Professional 1000x 32GB UHS-II SDR104
SanDisk Extreme Pro 16GB SDR104
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out mmc_host_set_uhs_voltage() so it can be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following functions are needed by the mmc block device driver, once it
converts to blkmq, therefore let's export them.
mmc_start_bkops()
mmc_start_request()
mmc_retune_hold_now()
mmc_retune_release()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Don't populate the const arrays mszs on the stack, instead make them
static. Makes the object code smaller by over 310 bytes:
Before:
text data bss dec hex filename
47527 8528 320 56375 dc37 drivers/mmc/host/dw_mmc.o
After:
text data bss dec hex filename
47055 8688 320 56063 daff drivers/mmc/host/dw_mmc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 3fc7eaef44 ("mmc: dw_mmc: Add external dma interface
support") use_dma no longer means only the data transfer mode, and
includes dma transmission channel. So make it more clear.
Signed-off-by: Ziyuan <ziyuan.biubiu@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On gen3 PCI-Express we should send command one by one.
If sending many commands in one packet will lead to a failure.
Signed-off-by: rui_feng <rui_feng@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out some common code that will also be used with blk-mq.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enhance mmc_blk_data_prep() to support CQE requests. That means adding
some things that for non-CQE requests would be encoded into the command
arguments - such as the block address, reliable-write flag, and data tag
flag. Also the request tag is needed to provide the command queue task id,
and a comment is added to explain the future possibility of defining a
priority.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use local variables in mmc_blk_data_prep() in preparation for adding CQE
support which doesn't use the output variables.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable or disable CQE when a card is added or removed respectively.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable the Command Queue if the host controller supports a command queue
engine. It is not compatible with Packed Commands, so make a note of that in the
comment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add core support for handling CQE requests, including starting, completing
and recovering.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the host can be claimed by a task. Change this so that the host
can be claimed by a context that may or may not be a task. This provides
for the host to be claimed by a block driver queue to support blk-mq, while
maintaining compatibility with the existing use of mmc_claim_host().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Callers already have the host claimed, so remove the unnecessary
calls to mmc_claim_host() and mmc_release_host().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I forgot to account for the fact that the device core holds a
reference to a device added with device_initialize() that need
to be released with a corresponding put_device() to reach a 0
refcount at the end of the lifecycle.
This led to a NULL pointer reference when freeing the device
when e.g. unbidning the host device in sysfs.
Fix this and use the device .release() callback to free the
IDA and free:ing the memory used by the RPMB device.
Before this patch:
/sys/bus/amba/drivers/mmci-pl18x$ echo 80114000.sdi4_per2 > unbind
[ 29.797332] mmc3: card 0001 removed
[ 29.810791] Unable to handle kernel NULL pointer dereference at
virtual address 00000050
[ 29.818878] pgd = de70c000
[ 29.821624] [00000050] *pgd=1e70a831, *pte=00000000, *ppte=00000000
[ 29.827911] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 29.833282] Modules linked in:
[ 29.836334] CPU: 1 PID: 154 Comm: sh Not tainted
4.14.0-rc3-00039-g83318e309566-dirty #736
[ 29.844604] Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support)
[ 29.851562] task: de572700 task.stack: de742000
[ 29.856079] PC is at kernfs_find_ns+0x8/0x100
[ 29.860443] LR is at kernfs_find_and_get_ns+0x30/0x48
After this patch:
/sys/bus/amba/drivers/mmci-pl18x$ echo 80005000.sdi4_per2 > unbind
[ 20.623382] mmc3: card 0001 removed
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function is used by the block layer queue to bail out of
requests if the current request is towards an RPMB
"block device".
This was done to avoid boot time scanning of this "block
device" which was never really a block device, thus duct-taping
over the fact that it was badly engineered.
This problem is now gone as we removed the offending RPMB block
device in another patch and replaced it with a character
device.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The RPMB partition on the eMMC devices is a special area used
for storing cryptographically safe information signed by a
special secret key. To write and read records from this special
area, authentication is needed.
The RPMB area is *only* and *exclusively* accessed using
ioctl():s from userspace. It is not really a block device,
as blocks cannot be read or written from the device, also
the signed chunks that can be stored on the RPMB are actually
256 bytes, not 512 making a block device a real bad fit.
Currently the RPMB partition spawns a separate block device
named /dev/mmcblkNrpmb for each device with an RPMB partition,
including the creation of a block queue with its own kernel
thread and all overhead associated with this. On the Ux500
HREFv60 platform, for example, the two eMMCs means that two
block queues with separate threads are created for no use
whatsoever.
I have concluded that this block device design for RPMB is
actually pretty wrong. The RPMB area should have been designed
to be accessed from /dev/mmcblkN directly, using ioctl()s on
the main block device. It is however way too late to change
that, since userspace expects to open an RPMB device in
/dev/mmcblkNrpmb and we cannot break userspace.
This patch tries to amend the situation using the following
strategy:
- Stop creating a block device for the RPMB partition/area
- Instead create a custom, dynamic character device with
the same name.
- Make this new character device support exactly the same
set of ioctl()s as the old block device.
- Wrap the requests back to the same ioctl() handlers, but
issue them on the block queue of the main partition/area,
i.e. /dev/mmcblkN
We need to create a special "rpmb" bus type in order to get
udev and/or busybox hot/coldplug to instantiate the device
node properly.
Before the patch, this appears in 'ps aux':
101 root 0:00 [mmcqd/2rpmb]
123 root 0:00 [mmcqd/3rpmb]
After applying the patch these surplus block queue threads
are gone, but RPMB is as usable as ever using the userspace
MMC tools, such as 'mmc rpmb read-counter'.
We get instead those dynamice devices in /dev:
brw-rw---- 1 root root 179, 0 Jan 1 2000 mmcblk0
brw-rw---- 1 root root 179, 1 Jan 1 2000 mmcblk0p1
brw-rw---- 1 root root 179, 2 Jan 1 2000 mmcblk0p2
brw-rw---- 1 root root 179, 5 Jan 1 2000 mmcblk0p5
brw-rw---- 1 root root 179, 8 Jan 1 2000 mmcblk2
brw-rw---- 1 root root 179, 16 Jan 1 2000 mmcblk2boot0
brw-rw---- 1 root root 179, 24 Jan 1 2000 mmcblk2boot1
crw-rw---- 1 root root 248, 0 Jan 1 2000 mmcblk2rpmb
brw-rw---- 1 root root 179, 32 Jan 1 2000 mmcblk3
brw-rw---- 1 root root 179, 40 Jan 1 2000 mmcblk3boot0
brw-rw---- 1 root root 179, 48 Jan 1 2000 mmcblk3boot1
brw-rw---- 1 root root 179, 33 Jan 1 2000 mmcblk3p1
crw-rw---- 1 root root 248, 1 Jan 1 2000 mmcblk3rpmb
Notice the (248,0) and (248,1) character devices for RPMB.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD clock should be disabled for clock value 0. It's not
right to just return. This may cause failure of signal
voltage switching.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay circuit used to support HS400 is calibrated based on two
additional clocks. When these clocks are not available and
FF_CLK_SW_RST_DIS is not set in CORE_HC_MODE, reset might fail. But on
some platforms this doesn't work properly and below dump can be seen in
the kernel log.
mmc0: Reset 0x1 never completed.
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00001102
mmc0: sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc0: sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
mmc0: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x00000002
mmc0: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc0: sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
mmc0: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc0: sdhci: Caps: 0x742dc8b2 | Caps_1: 0x00008007
mmc0: sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc0: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ============================================
Add support for the additional calibration clocks to allow these
platforms to be configured appropriately.
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By stuffing the runtime controlled clocks into a clk_bulk_data array we
can utilize the newly introduced bulk clock operations and clean up the
error paths. This allow us to handle additional clocks in subsequent
patch, without the added complexity.
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI controllers on Tegra186 support 40 bit addressing.
IOVA addresses are 48-bit wide on Tegra186.
SDHCI host common code sets dma mask as either 32-bit or 64-bit.
To avoid access issues when SMMU is enabled, disable 64-bit dma.
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since this driver checks if the return value of dma_map_sg() is minus
or not and keeps to enable the DMAC, it may cause kernel panic when
the dma_map_sg() returns 0. So, this patch fixes the issue.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the commit de3ee99b09 ("mmc: Delete bounce buffer handling")
deletes the bounce buffer handling, a request data size will be referred
to max_{req,seg}_size instead of MMC_QUEUE_BOUNCESZ (64k bytes).
In other hand, renesas_sdhi_internal_dmac.c will set very big value of
max_{req,seg}_size because the max_blk_count is set to 0xffffffff.
And then, "swiotlb buffer is full" happens because swiotlb can handle
a memory size up to 256k bytes only (IO_TLB_SEGSIZE = 128 and
IO_TLB_SHIFT = 11).
So, as a workaround, this patch avoids the issue by setting
the max_{req,seg}_size up to 256k bytes if swiotlb is running.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default for d3_retune is true, but that was not being set in all cases,
which results in eMMC errors because re-tuning has not been done.
Fix by initializing d3_retune to true.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: c959a6b00f ("mmc: sdhci-pci: Don't re-tune with runtime pm for some Intel devices")
Cc: stable@vger.kernel.org # v4.12+
Reported-and-tested-by: ojab <ojab@ojab.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been reported that some platforms (odroid-c2) may require
a different tx phase setting to operate at high speed (hs200 and hs400)
To improve the situation, this patch includes tx phase in the tuning
process.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the phase when POWER_ON is set the set_ios() call means that the
phase is reset almost every time the set_ios() is called, while the
expected behavior was to reset the phase on a power cycle.
This had gone unnoticed until now because in all mode (except hs400) the
tuning is done after the last to set_ios(). In such case, the tuning
result is used anyway. In HS400, there are a few calls to set_ios() after
the tuning is done, overwriting the tuning result.
Resetting the phase on POWER_UP instead of POWER_ON solve the problem.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using CLK_DIVIDER_ROUND_CLOSEST is unsafe as the mmc clock could be
rounded to a rate higher the specified rate. Removing this flag ensure
that, if the rate needs to be rounded, it will be rounded down.
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In may, Steven sent a patch deleting the bounce buffer handling
and the CONFIG_MMC_BLOCK_BOUNCE option.
I chose the less invasive path of making it a runtime config
option, and we merged that successfully for kernel v4.12.
The code is however just standing in the way and taking up
space for seemingly no gain on any systems in wide use today.
Pierre says the code was there to improve speed on TI SDHCI
controllers on certain HP laptops and possibly some Ricoh
controllers as well. Early SDHCI controllers lacked the
scatter-gather feature, which made software bounce buffers
a significant speed boost.
We are clearly talking about the list of SDHCI PCI-based
MMC/SD card readers found in the pci_ids[] list in
drivers/mmc/host/sdhci-pci-core.c.
The TI SDHCI derivative is not supported by the upstream
kernel. This leaves the Ricoh.
What we can however notice is that the x86 defconfigs in the
kernel did not enable CONFIG_MMC_BLOCK_BOUNCE option, which
means that any such laptop would have to have a custom
configured kernel to actually take advantage of this
bounce buffer speed-up. It simply seems like there was
a speed optimization for the Ricoh controllers that noone
was using. (I have not checked the distro defconfigs but
I am pretty sure the situation is the same there.)
Bounce buffers increased performance on the OMAP HSMMC
at one point, and was part of the original submission in
commit a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new
omap hsmmc controller for 2430 and 34xx, v3")
This optimization was removed in
commit 0ccd76d4c2 ("omap_hsmmc: Implement scatter-gather
emulation")
which found that scatter-gather emulation provided even
better performance.
The same was introduced for SDHCI in
commit 2134a922c6 ("sdhci: scatter-gather (ADMA) support")
I am pretty positively convinced that software
scatter-gather emulation will do for any host controller what
the bounce buffers were doing. Essentially, the bounce buffer
was a reimplementation of software scatter-gather-emulation in
the MMC subsystem, and it should be done away with.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Cc: Steven J. Hill <Steven.Hill@cavium.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Suggested-by: Steven J. Hill <Steven.Hill@cavium.com>
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver strength selection is missed and required when selecting
hs400es. So, It is added here.
Fixes: 81ac2af657 ("mmc: core: implement enhanced strobe support")
Cc: stable@vger.kernel.org
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The functions sdhci_omap_set_ios, sdhci_omap_set_power and
sdhci_omap_get_min_clock are local to the source and do not need
to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'sdhci_omap_set_ios' was not declared. Should it be static?
symbol 'sdhci_omap_set_power' was not declared. Should it be static?
symbol 'sdhci_omap_get_min_clock' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel host controllers (e.g. CNP) use an ACPI device-specific method
to ensure correct voltage switching. Fix voltage switch for those, by
adding a call to the DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some change for v4.14 broke the debug output for TMIO. But since it was
not helpful to me and too noisy for my taste anyhow, let's just remove
it instead of fixing it. We'll find something better if we'd need it...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a new sdhci-omap driver to configure the eMMC/SD/SDIO controller
in TI's OMAP SoCs making use of the SDHCI core library. For OMAP specific
configurations, populate sdhci_ops with OMAP specific callbacks and use
SDHCI quirks.
Enable only high speed mode for both SD and eMMC here and add other
UHS mode support later.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PBIAS voltage should be set along with setting vqmmc voltage and
these voltages should be set as part of start_signal_voltage_switch
callback. However since omap_hsmmc is about to be deprecated,
remove setting of PBIAS voltage leaving the PBIAS voltage to be
at the reset value of 3.3V (we'll never have to change this to 1.8V
since UHS mode support will not be added to omap_hsmmc). This will
let pbias regulator driver to be fixed to support a maximum voltage of
3.3V.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_DEBUG was moved and one letter got strangely capitalized.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_init_request() depends on card->bouncesz so it must be calculated
before blk_init_allocated_queue() starts allocating requests.
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the..")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Add support for r8a7743/5 SoC.Renesas RZ/G1[ME] (R8A7743/5) SDHI
is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using __bf_shf does not compile on arm 32 architecture.
This has gone unnoticed till now cause the driver is only used on arm64.
In addition, __bf_shf was already used in the driver without any issue.
It was used on a constant value, so the call was probably optimized
away.
Replace __bf_shf by __ffs fixes the problem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable runtime pm support for xenon controller, which uses 50ms
auto runtime suspend by default.
Reimplement system standby based on runtime pm API.
Introduce restore_needed to restore the Xenon specific registers
when resume.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_start_areq() is an internal mmc core API. Move the declaration
accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It does not make sense for qcom dml code to be a seperate module, as
this has just 2 helper functions specific to qcom, and used directly by
mmci driver, so just compile this along with main mmci driver.
This would also fix issues arrising due to Kconfig combinations between
mmci and qcom dml.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We might be into some troubles if the bootloader misconfigured the MMC
controller.
We currently only de-assert the reset line at probe time, which means that
if the device was already out of reset, we're going to keep whatever state
was set already.
Switch to a reset instead of the deassert to have a device in a pristine
state when we start operating.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rework tuning function of the rx phase. Now that the phase can be
more precisely set using CCF, test more phase setting and find the
largest working window. Then the tuning selected is the one at the
center of the window.
This rework allows to use new modes, such as UHS SDR50
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial default tx phase was set to 0 while the datasheet recommends 270.
Some cards fails to initialize with this setting and eMMC mode DDR52 does
not work.
Changing this setting to 270 fixes these issues, without any regression
so far
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement voltage switch callback (shamelessly copied from sunxi mmc
driver). This allow, with the appropriate tuning function, to use
SD ultra high speed modes.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Several phases can be controlled on the meson-gx controller, the core, tx
and rx clock phase. The tx and rx uses delays to allow more fine grained
setting of the phase. To properly compute the phase using delays,
accessing the clock rate is necessary.
Instead of ad-hoc functions, use the common clock framework to set the
clock phases (and access the clock rate while doing it).
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the card_busy callback to be able to verify that the
card is done dealing with voltage switch, when the support is
added later on.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems that the mmc clock is also used and required, somehow, by
the controller itself.
It is shown during init, when writing to CFG while the divider is set
to 0 will crash the SoC. During a voltage switch, the controller may
crash and the card may then fail to exit busy state if the clock is
stopped.
To avoid this, it is best to keep the clock running for the controller,
except during rate change. However, we still need to be able to gate
the clock out of the SoC. Let's use the pinmux for this, and fallback
to gpio mode (pulled-down) when we need to gate the clock
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In DDR modes, meson mmc controller requires an input rate twice as fast
as the output rate
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Thanks to devm, carrying the clock structure around after init is not
necessary. Rework the function to remove these from the controller host
data.
Finally, set initial mmc clock rate before enabling it, simplifying the
exit condition.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clean-up clk_set function to prepare the next changes (DDR and clk-stop)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove conditional write of cfg register. Warn if set_clk fails for some
reason. Consistently use host->dev instead of mixing with mmc_dev(mmc)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cfg init function overwrite values set in the clk init function
Remove the cfg pokes from the clk init. Actually, trying to use
the CLK_AUTO, like initially tried in clk_init, would break
the card initialization
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On boot, the clock divider value is 0 which is a weird unsupported value.
For example, accessing the cfg register with this value set would crash
the SoC.
Previous change removed 0 as possible value for CCF but forgot to properly
initialize the register before registering the clock. This leads to the
CCF finding an illegal value, which it complains about.
Initialize the register properly in a standalone patch so the fix can be
picked up if necessary. The change this fixed is: "mmc: meson-gx: remove
CLK_DIVIDER_ALLOW_ZERO clock flag".
Reported-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention for this patch is to help folks debug the failure
like this:
dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 28,32 bit
host data width,256 deep fifo
dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual
400000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz,
actual 50000000HZ div = 0)
mmc0: new high speed SDHC card at address 0007
mmcblk: probe of mmc0:0007 failed with error -28
The reason may be some buggy userspace daemon miss the disk remove
uevent sometimes so it would finally make the SD card not work.
So from the dmesg it only shows a errno of -28 but still don't understand
what happened.
For quick reproduce this, we could set max_devices to 8 and run
for i in $(seq 1 9); do
echo "========================" $i
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind
sleep .5
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/bind
sleep .5
mount -t vfat /dev/mmcblk0 /mnt
sleep .5
done
Another possible reason would be the device has more partitions than
what we support, so that they have to increase their max_devices.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This will be useful when drivers want to reuse either suspend or
resume callback instead of whole of sdhci_pltfm_pmops.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit provides similar cleanups as commit 83eacdfa25 ("mmc:
sdhci: disable the clock in sdhci_pltfm_unregister()") did for
unregister hooks.
sdhci-brcmstb.c and sdhci-sirf.c implement their own suspend/resume
hooks to handle pltfm_host->clk. Move clock handling to sdhci_pltfm.c
so that the drivers can reuse sdhci_pltfm_pmops.
The following drivers did not previously touch pltfm_host->clk during
suspend/resume, but now do:
- sdhci-bcm-kona.c
- sdhci-dove.c
- sdhci-iproc.c
- sdhci-pxav2.c
- sdhci-tegra.c
- sdhci-xenon.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The difference between sdhci_pxav2_remove() and sdhci_pltfm_unregister()
is clk_put(). It will go away by using the managed resource clk, then
sdhci_pltfm_unregister() can be reused.
Also, rename the jump labels to say what the goto does. (Coding style
suggested by Documentation/process/coding-style.rst)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the probe function initializes the PHY, but PHY settings
are lost during the sleep state. Restore the PHY registers when
resuming.
To facilitate this, split sdhci_cdns_phy_init() into the DT parse
part and PHY update part so that the latter can be invoked from the
resume hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Support HS400 Enhanced Strobe feature in Xenon.
Enable Enhanced Strobe together with Data Strobe.
Disable Enhanced Strobe when eMMC is not in HS400 mode.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TI's implementation of sdhci controller used in DRA7 SoC's has
CRC in responses with length 136 bits. Add quirk to indicate
the controller has CRC in MMC_RSP_136. If this quirk is
set sdhci library shouldn't shift the response present in
SDHCI_RESPONSE register.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Read each register only once and move the code to a separate function so
that it is not jammed against the 80 column margin.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove unused clock rate defines. These should not be defined but
requested from the clock framework.
Also correct typo on the DELAY register
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove CLK_DIVIDER_ALLOW_ZERO. This flag means that a 1 based divider
with a 0 value will behave as a bypass clock
The mmc divider does not behave like this, a 0 value disables the clock
Remove this flag so CCF never allows a 0 value on this clock
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CCF generic mux will shift the mask using the value defined in shift
Define the mask accordingly
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a block device to
mmc_blk_ioctl[_multi]_cmd(), let's pass struct mmc_blk_data()
so we operate ioctl()s on the MMC block device representation
rather than the vanilla block device.
This saves a little duplicated code and makes it possible to
issue ioctl()s not targeted for a specific block device but
rather for a specific partition/area.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a struct mmc_blk_data * to mmc_blk_part_switch()
let's pass the actual partition type we want to switch to. This
is necessary in order not to have a block device with a backing
mmc_blk_data and request queue and all for every hardware partition,
such as RPMB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_ioctl() calls either mmc_blk_ioctl_cmd() or
mmc_blk_ioctl_multi_cmd() and each of these make the same
check. Factor it into a new helper function, call it on
both branches of the switch() statement and save a chunk
of duplicate code.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we don't have the block layer enabled, we do not present card
status and extcsd in the debugfs.
Debugfs is not ABI, and maintaining files of no relevance for
non-block devices comes at a high maintenance cost if we shall
support it with the block layer compiled out.
The debugfs entries suffer from all the same starvation
issues as the other userspace things, under e.g. a heavy
dd operation.
The expected number of debugfs users utilizing these two
debugfs files is already low as there is an ioctl() to get the
same information using the mmc-tools, and of these few users
the expected number of people using it on SDIO or combo cards
are expected to be zero.
It is therefore logical to move this over to the block layer
when it is enabled, using the new custom requests and issue
it using the block request queue.
On the other hand it moves some debugfs code from debugfs.c
and into block.c.
Tested during heavy dd load by cat:in the status file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function retrieves the status of the card with the default
number of retries. Since the block layer wants to use this, and
since the block layer is a loadable kernel module, we need to
export this symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have a data pointer for the ioctl() data, but we need to
pass other data along with the DRV_OP:s, so make this a
void * so it can be reused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Get rid of boilerplate code by using module_platform_driver macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new lockdep annotations for completions cause a warning in the
mmc test module, in a function that now has four 150 byte structures
on the stack:
drivers/mmc/core/mmc_test.c: In function 'mmc_test_nonblock_transfer.constprop':
drivers/mmc/core/mmc_test.c:892:1: error: the frame size of 1360 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The mmc_test_ongoing_transfer function evidently had a similar problem,
and worked around it by using dynamic allocation.
This generalizes the approach used by mmc_test_ongoing_transfer() and
applies it to mmc_test_nonblock_transfer() as well.
Fixes: cd8084f91c ("locking/lockdep: Apply crossrelease to completions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC is not a standard SD host controller. SDHCI_CAPABILITIES_1
register address is 0x44 while it's 0x114 (ESDHC_CAPABILITIES_1)
for eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD controller with SDHCI_QUIRK_NO_HISPD_BIT quirk probably
use high speed enable bit for other purpose. So this bit
shouldn't be changed for high speed enabling for this type of
SD controller.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the sdhci-s3c version with
the generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the sdhci-pci version with
the generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the tegra version with the
generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hosts supporting 8-bit bus are marked accordingly. If MMC_CAP_8_BIT_DATA
is not among host capabilities, 8BITBUS bit will never be set and it
is not cleared in case some non-SDHCI3 host uses it for something else.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQE needs to be off for the host controller to accept non-CQ commands. Turn
off the CQE before sending commands, and ensure it is off in any reset or
power management paths, or re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_return_hold() / mmc_retune_release() are used around a group of
commands to prevent re-tuning between the commands. Re-tuning can still
happen before the first command. In some cases, re-tuning must be
prevented entirely. Add mmc_retune_hold_now() for that purpose. It is
added in preparation for CQE support where it will be used by CQE recovery.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Packed commands support was removed but some bits got left behind. Remove
them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sunxi_mmc_clk_set_phase expects the actual card clock rate to be passed
to it. When the internal divider code was reworked in change ("mmc: sunxi:
Support MMC DDR52 transfer mode with new timing mode"), this requirement
was missed, and the module clock rate was passed in instead. This broke 8
bit DDR MMC on old controllers, as the module clock rate is double the
card clock rate, for which we have no valid delay settings.
Fix this by applying the internal divider to the clock rate right after
we configure it in hardware.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the 64 bit sdbuf width on Renesas R-Car Gen3. If the
registers are 8 byte apart, the width is also 64 bit. For all others,
the width is 32 bit, even if the registers are only 16 bit apart.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't use this new define yet, but it is helpful to document which
versions we know of.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is documented, so enable it to follow the recommendation in the docs
and also save a few cycles.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is one SDHI instance on Gen2 which does not have the CBSY bit.
So, turn CBSY usage into an extra flag and set it accordingly. This has
the additional advantage that we can also set it for other incarnations
later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon specific system-level suspend and resume support.
Especially during resume, re-configure Xenon specific registers
since registers setting will be lost in suspend if Xenon is power off.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the databook of designware mmc controller 2.70a, table 3-2, cmd
done interrupt should be fired as soon as the the cmd is sent via
cmd line. And the response timeout interrupt should be generated
unconditioinally as well if the controller doesn't receive the resp.
However that doesn't seem to meet the fact of rockchip specified Soc
platforms using dwmmc. We have continuously found the the cmd done or
response timeout interrupt missed somehow which took us a long time to
understand what was happening. Finally we narrow down the root to
the reconstruction of sample circuit for dwmmc IP introduced by
rockchip and the buggy design sweeps over all the existing rockchip
Socs using dwmmc disastrously.
It seems no way to work around this bug without the proper break-out
mechanism so that we seek for a parallel pair the same as the handling
for missing data response timeout, namely dto timer. Adding this cto
timer seems easily to handle this bug but it's hard to restrict the code
under the rockchip specified context. So after merging this patch, it
sets up the cto timer for all the platforms using dwmmc IP which isn't
ideal but at least we don't advertise new quirk here. Fortunately, no
obvious performance regression was found by test and the pre-existing
similar catch-all timer for sdhci has proved it's an acceptant way to
make the code as robust as possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
[shawn.lin: rewrite the code and the commit msg throughout]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit modifies dw_mci_probe(), it moves reset assertion before
drv_data->init(host)
Some driver needs to access controller registers in its .init() ops. So,
in order to make such access safe, we should do controller reset before
.init() being called.
Signed-off-by: Wei Li <liwei213@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Programming legacy HOST SDMA Buffer Boundary bits in Block Size Register
(0x04) is not supported in Qualcomm sdhci controllers. Writing to this
would cause the controller not to transfer last block in case block size
is 4 bytes or less.
This issue was noticed while testing sdio wlan card on Qcom DB410c board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdma_boundary member to struct sdhci_host to give more
flexibility to drivers to control the sdma boundary buffer value and
also to fix issue on some sdhci controllers which are broken when
HOST SDMA Buffer Boundary is programmed in Block Size Register (0x04)
when using ADMA. Qualcomm sdhci controller is one of such type, writing
to this bits is un-supported.
Default value of sdma_boundary is set to SDHCI_DEFAULT_BOUNDARY_ARG.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The structure renesas_sdhi_internal_dmac_dma_ops is only passed as
the second argument to renesas_sdhi_probe, which is const, so
renesas_sdhi_internal_dmac_dma_ops can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, so the sdhci_pltfm_data structure
can be const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, so the sdhci_pltfm_data structure can
be const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the SD physical layer simplified specification V4.10,
section 4.6.2, CSD version 1.0 SD card should use taac, nsac
and r2w_factor for calculating the data access time. But the
taac and nsac for SDHC(CSD version 2.0) are always fixed and
the software should use the recommended value for timeout. When
parsing the CSD, we sanely set them to zero for SDHC(CSD version
2.0), all the calculation for timeout_ns and timeout_clk is zero
as well. So what we actually want to limit here is either SDHC
case or unreasonable timeout reported by the cards. In principle
we should at least be able to remove the bogus check for the
mmc_card_blockaddr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One issue was found on a removable high speed sd card with
runtime pm enabled.
When SD card is unplugged, it keep printing "Switching to 3.3V
signalling voltage failed".
And found below sequence triggers the error.
mmc_rescan
-> mmc_sd_detect
-> mmc_power_off -- mmc->ios.vdd is updated to 0.
-> mmc_claim_host
-> sdhci_runtime_resume_host
-> sdhci_start_signal_voltage_switch
-> mmc_regulator_set_vqmmc
-> mmc_ocrbitnum_to_vdd
When mmc_ocrbitnum_to_vdd is called, the mmc->ios.vdd is 0, so it
always return -EINVAL. The signal switch will always fail and
print out warning.
Ignore restoring the I/O state when runtime resume if MMC_POWER_OFF.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The A83T MMC support code introduces the timings mode switch, however
such a switch doesn't exist on new SoCs with only new timings mode.
Only execute the switch if the SoC really have the timings mode switch,
to fix the regression shown on new timings mode only SoCs (A64, H5,
etc).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SoCs do not support clk delays for MMC in the clock control unit.
These include the old controllers in A10/A10s/A13/R8, and the new eMMC
controller in A64. The config structure for these controllers do not
specify clk_delays, but the check for this was replaced in change
"mmc: sunxi: Support controllers that can use both old and new timings".
This patch adds back the check for clk_delays, and also adds comments
for both checks in sunxi_mmc_clk_set_phase().
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The third MMC controller (MMC2) on the Allwinner A83T SoC is slightly
different. It supports a wider 8-bit bus, has a dedicated controllable
reset pin for eMMC, and a "new timing mode" which is supposed to deliver
better signals and thus better performance.
Add a compatible for this one to use the new timing mode not found in the
other controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC controller can support DDR52 transfers under the new timing
mode. According to the BSP kernel, the module clock has to be double
the card clock, regardless of the bus width. The default timings in
the hardware can be used.
This also reworks the code setting the internal divider, getting rid
of a extra conditional.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the SoCs that introduced the new timing mode for MMC controllers,
both the old (where the clock delays are set in the CCU) and new
(where the clock delays are set in the MMC controller) timing modes
are available, and we have to support them both. However there are
two bits that control which mode is active. One is in the CCU, the
other is in the MMC controller. The settings on both sides must be
the same, or nothing will work.
The sunxi-ng clock driver provides an API to query and set the
active timing mode. At probe time, we try to set the active mode
to the "new timing mode". If it succeeds, we can then use the MMC
controller in the new mode. If not, we fall back to the old mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provide a whitelist for Gen3 SoC ES versions for both the SYS DMAC and
internal DMAC variants of the SDHI driver. This is to allow drivers to
only initialise for Gen3 SoC ES versions for which they are the appropriate
DMAC implementation. Currently internal DMAC is the appropriate
implementation for all supported Gen3 SoC ES versions.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix up a power state in case PCI device has an ACPI companion.
Do it only for Intel Merrifield for now.
This is almost copy'n'paste of part of sdhci_acpi_probe() and might be
split out to a helper function in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ACPI_COMPANION() macro reduces a code to get a companion device out of
struct device.
Use it instead of an old method.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: "Steven J. Hill" <Steven.Hill@cavium.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I cannot see why this is needed. kmap() should be safe in this case.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6952 880 0 7832 1e98 drivers/mmc/host/via-sdmmc.o
File size After adding 'const':
text data bss dec hex filename
7032 800 0 7832 1e98 drivers/mmc/host/via-sdmmc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci uses CONFIG_MMC_DEBUG for showing ADMA descriptor
when occurring ADMA error. And it's also used to dump the
registers whenever calling sdhci_add_host.
On one hand, I don't see any burden to always print the state
ADMA descriptor as it's rare and will help folks better understand
what was happening when seeing ADMA error.
On the other, folks may be interested in checking some registers
at probe time. So we remove the sdhci_dumpregs from __sdhci_add_host
and print some really useful registers in sdhci_setup_host.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wbsd only use this to print some unsupported command.
However the pr_warn should be enough for dynamic log
control and CONFIG_MMC_DEBUG seems bogus here. Remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have removed all code depending on CONFIG_MMC_DEBUG
from mmc core now. So it's safe to make CONFIG_MMC_DEBUG
just for host drivers only and we expect to kill this option
in the future.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are lots of debug message in core.c which use pr_debug
for better dynamic log level control. So it doesn't make sense
for those print to still keep working only under CONFIG_MMC_DEBUG.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the check within mmc_mrq_prep seems to be all-or-none
proposition, so it doesn't make sense to only check the
length of sglist only under the CONFIG_MMC_DEBUG context.
I'd prefer to always keep the check there unconditionally.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduce a warning
drivers/mmc/host/sdhci-acpi.c: In function 'sdhci_acpi_sdio_probe_slot':
drivers/mmc/host/sdhci-acpi.c:297:21: warning: variable 'host' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This increases consistency of the code across the sdhci family.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for_each_child_of_node performs an of_node_get on each iteration, so a
break out the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(e1,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds deepest (Backup+Self-Refresh) PM support to the ATMEL SAMA5D2
SoC's SDHCI controller.
When resuming from deepest state, it is required to restore preset
registers as the registers are lost since VDD core has been shut down
when entering deepest state on the SAMA5D2. The clocks need to be
reconfigured as well.
The other registers and init process are taken care of by the SDHCI
core.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The setting of clocks and presets is currently done in probe only but
once deep PM support is added, it'll be needed in the resume function.
Let's create a function for this setting.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We got a warning:
drivers/mmc/host/atmel-mci.c:1086:15: warning: variable 'sg_len' set but
not used [-Wunused-but-set-variable]
Ideally we should check to see if sg_len is zero but looking
into the code closely, I didn't find any possible to do that as
atmci_start_request didn't even deploy any error handling for
its host->prepare_data hook. So even we return error value for iflags
like what other host drivers did, for instance, sdhci and dwmmc, it still
need some extra work to improve the code.
Just remove it to silent the warning, although it isn't perfect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and leave a long standing compile warning:
drivers/mmc/host/sdhci-xenon.c: In function 'xenon_probe':
drivers/mmc/host/sdhci-xenon.c:447:21: warning: variable 'priv' set but
not used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduced a long standing compile
warning:
drivers/mmc/core/block.c: In function 'power_ro_lock_store':
drivers/mmc/core/block.c:191:19: warning: variable 'card' set but not
used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We got a compile warning for mxcmmc,
drivers/mmc/host/mxcmmc.c: In function 'mxcmci_data_done':
drivers/mmc/host/mxcmmc.c:661:6: warning: variable 'data_error' set but
not used [-Wunused-but-set-variable]
The easiest method is to remove the data_error. But looking into
the code closely, I think we should check the return value of
mxcmci_finish_data as if it got data->error(the same as data_error),
we shouldn't try to read the response.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a trivial fix for that found by reading the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
if user plug out sd card slowly, finally card is plugged out but
cat /proc/partitions can find that card is still exist in kernel.
that's because alougth get card detect interrupt but CMD13 still
can get correct response(all other pins are connected expect card
detect pin).
add ops->get_cd() can avoid this issue.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
array width is on-stack and not modified and should be
made static const.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Most registers need to wait until the command is completed, not
necessarily until the bus is free. At least, R-Car 2+ SoCs can signal
that via the CBSY bit, so let's use it there instead of SCLKDIVEN to
save a little bit of delay.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our hardware engineers confirmed that it is unnecessary to wait when
turning the clock on/off. The documentation was a tad vague, so we
used to play safe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When defining bits, make sure we always have a reference to the register
they belong to. For now, renaming all bits properly seems too intrusive,
so at least make sure we have proper documentation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I always anticipated this code to be not correct, but now I had a test
case to prove it. According to all documentation I have, setting the
TMIO_STOP_STP bit ever only worked during block transfers. This bit is
like manually enforcing an autocmd12 during a so far seamless transfer.
It does NOT work when the block transfer had errors. It also does NOT
work with any other cmd except block commands. For all those, CMD12 has
to be treated like any other command. So, basically, we could use this
bit only for mrq->data->stop cmds. But for these, we happily use the
autocmd12 feature using the TMIO_STOP_SEC bit. As a result, the above
bit is not useful for us and we need to treat CMD12 as a regular cmd
always. Just remove the special handling code. Note that the BSP
recognized this issue as well yet had a more cautious solution to the
problem [1]. Which is understandable but makes CMD12 handling even more
complicated.
Checked with a Renesas Salvator-X/M3-W which needed to send CMD12 when
retuning one of my SD cards.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas-bsp.git/commit/?id=2838a2ff8ca776f6d18b7fbbe75f3df8dd64183a
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jan Klötzke <jan.kloetzke@preh.de>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() returns an error code, but the mxcmmc driver
ignores it and always returns -EINVAL. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Local variable transfer_error is assigned to a constant value and
it is never updated again.
Remove this variable and the dead code it guards.
Addresses-Coverity-ID: 1222110
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reduce max_segs to 64, a value that allows allocation of an entire
EDMA descriptor list within a single page - EDMA descriptors
are 40 bytes and the header is much larger. This avoids doing a
higher order GFP_ATOMIC allocation in edma_prep_slave_sg
when setting up a transfer which can potentially fail due to
fragmentation under heavy I/O load.
The current value of 1024 is unusually high in comparison to
other mmc host drivers which mostly use values of between 1
and 256. The EDMA driver at present splits lists above 20
segments in any case so reducing the size of lists we pass to
it shouldn't add much overhead.
Signed-off-by: Will Newton <willn@resin.io>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new variant of the SDHI driver to support R-Car Gen3 with DMA via
on-chip bus mastering. Since the DMAC is in a part of the SDHI module it
is not suitable to be used via DMA Engine.
Clearing of DM_CM_INFO1 after DMA thanks to Dirk Behme
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add dataend to DMA ops to allow DMAC implementation dependent
handling of DMA data end.
Also implement the operation for SDHI.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow TMIO and SDHI driver implementations to provide values for
max_segs and max_blk_count.
A follow-up patch will set these values for Renesas Gen3 SoCs
the using an SDHI driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11586 624 0 12210 2fb2 drivers/mmc/host/omap_hsmmc.o
File size After adding 'const':
text data bss dec hex filename
11778 432 0 12210 2fb2 drivers/mmc/host/omap_hsmmc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 2a842acab1 ("block: introduce new block status code type") changed
the error type but not in patches merged through the mmc tree, like
commit 0493f6fe5b ("mmc: block: Move boot partition locking into a driver
op"). Fix one error code that is incorrect and also use BLK_STS_OK in
preference to 0.
Fixes: 17ece345a0 ("Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We to some extent should tolerate R1_OUT_OF_RANGE for open-ending
mode as it is expected behaviour and most of the backup partition
tables should be located near some of the last blocks which will
always make open-ending read exceed the capacity of cards.
Fixes: 9820a5b111 ("mmc: core: for data errors, take response of stop cmd into account")
Fixes: a04e6bae9e ("mmc: core: check also R1 response for stop commands")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the default err value to -EINVAL, make sure the card only
has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage
setting when select hs400es mode.
Fixes: commit 1720d3545b ("mmc: core: switch to 1V8 or 1V2 for hs400es mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc driver always relied on CMD12 to stop transmission.
However if CMD12 is not issued at the correct timing, the card will
indicate a out of range error. With certain cards in some of the
DRA7 based boards, -EIO error is observed. By Adding CMD23 capability,
the MMC core will send MMC_SET_BLOCK_COUNT command before
MMC_READ_MULTIPLE_BLOCK/MMC_WRITE_MULTIPLE_BLOCK commands.
commit a04e6bae9e ("mmc: core: check also R1 response for
stop commands") exposed this bug in omap_hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 304419d8a7 ("mmc: core: Allocate per-request data using the
block layer core") refactored mechanism of queue handling caused
mmc_init_request() can be called just after mmc_cleanup_queue() caused null
pointer dereference.
Another commit bbdc74dc19 ("mmc: block: Prevent new req entering queue
after its cleanup") tried to fix the problem. However it actually miss one
corner case.
We could still reproduce the issue mentioned with these steps:
(1) insert a SD card and mount it
(2) hotplug it, so it will leave md->usage still be counted
(3) reboot the system which will sync data and umount the card
[Unable to handle kernel NULL pointer dereference at virtual address
00000000
[user pgtable: 4k pages, 48-bit VAs, pgd = ffff80007bab3000
[[0000000000000000] *pgd=000000007a828003, *pud=0000000078dce003,
*pmd=000000007aab6003, *pte=0000000000000000
[Internal error: Oops: 96000007 [#1] PREEMPT SMP
[Modules linked in:
[CPU: 3 PID: 3507 Comm: umount Tainted: G W
4.13.0-rc1-next-20170720-00012-g9d9bf45 #33
[Hardware name: Firefly-RK3399 Board (DT)
[task: ffff80007a1de200 task.stack: ffff80007a01c000
[PC is at mmc_init_request+0x14/0xc4
[LR is at alloc_request_size+0x4c/0x74
[pc : [<ffff0000087d7150>] lr : [<ffff000008378fe0>] pstate: 600001c5
[sp : ffff80007a01f8f0
....
[[<ffff0000087d7150>] mmc_init_request+0x14/0xc4
[[<ffff000008378fe0>] alloc_request_size+0x4c/0x74
[[<ffff00000817ac28>] mempool_create_node+0xb8/0x17c
[[<ffff00000837aadc>] blk_init_rl+0x9c/0x120
[[<ffff000008396580>] blkg_alloc+0x110/0x234
[[<ffff000008396ac8>] blkg_create+0x424/0x468
[[<ffff00000839877c>] blkg_lookup_create+0xd8/0x14c
[[<ffff0000083796bc>] generic_make_request_checks+0x368/0x3b0
[[<ffff00000837b050>] generic_make_request+0x1c/0x240
So mmc_blk_put wouldn't calling blk_cleanup_queue which actually the
QUEUE_FLAG_DYING and QUEUE_FLAG_BYPASS should stay. Block core expect
blk_queue_bypass_{start, end} internally to bypass/drain the queue before
actually dying the queue, so it didn't expose API to set the queue bypass.
I think we should set QUEUE_FLAG_BYPASS whenever queue is removed, although
the md->usage is still counted, as no dispatch queue could be found then.
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the block layer core")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the device is non removable, the card detect signal is often used
for another purpose i.e. muxed to another SoC peripheral or used as a
GPIO. It could lead to wrong behaviors depending the default value of
this signal if not muxed to the SDHCI controller.
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change to print the information about when the deprecated "num-slots" DT
binding is being used, as to avoid confusion when browsing the log:
dwmmc_rockchip fe320000.dwmmc: 'num-slots' was deprecated.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: d30a8f7bdf ("mmc: dw_mmc: deprecated the "num-slots" property")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove unused callbacks in the omap_hsmmc_platform_data structure
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register for the "new timing mode" also has bit fields for setting
output and sample timing phases. According to comments in Allwinner's
BSP kernel, the default values are good enough.
Keep the default values already in the hardware when setting new timing
mode, instead of overwriting the whole register.
Fixes: 9a37e53e45 ("mmc: sunxi: Enable the new timings for the A64 MMC
controllers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Restore some behaviour of MMC_IOC_MULTI_CMD commands
- Fix using un-initialized variable in mmc_blk_issue_drv_op()
- Fix mmc block queue cleanup
MMC host:
- sdhci-acpi: Workaround conflict with PCI wifi on GPD Win handheld
- tmio-mmc: Fix bad pointer math
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zgfL
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.13 rc1.
MMC core:
- Restore some behaviour of MMC_IOC_MULTI_CMD commands
- Fix using un-initialized variable in mmc_blk_issue_drv_op()
- Fix mmc block queue cleanup
MMC host:
- sdhci-acpi: Workaround conflict with PCI wifi on GPD Win handheld
- tmio-mmc: Fix bad pointer math"
* tag 'mmc-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: tmio-mmc: fix bad pointer math
mmc: block: Prevent new req entering queue after its cleanup
mmc: block: Let MMC_IOC_MULTI_CMD return zero again for zero entries
mmc: block: Initialize ret in mmc_blk_issue_drv_op() for MMC_DRV_OP_IOCTL
mmc: sdhci-acpi: Workaround conflict with PCI wifi on GPD Win handheld
The existing code gives an incorrect pointer value.
The buffer pointer 'buf' was of type unsigned short *, and 'count' was a
number in bytes. A cast of buf should have been used.
However, instead of casting, just change the code to use u32 pointers.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8185e51f35: ("mmc: tmio-mmc: add support for 32bit data port")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
__GFP_REPEAT was designed to allow retry-but-eventually-fail semantic to
the page allocator. This has been true but only for allocations
requests larger than PAGE_ALLOC_COSTLY_ORDER. It has been always
ignored for smaller sizes. This is a bit unfortunate because there is
no way to express the same semantic for those requests and they are
considered too important to fail so they might end up looping in the
page allocator for ever, similarly to GFP_NOFAIL requests.
Now that the whole tree has been cleaned up and accidental or misled
usage of __GFP_REPEAT flag has been removed for !costly requests we can
give the original flag a better name and more importantly a more useful
semantic. Let's rename it to __GFP_RETRY_MAYFAIL which tells the user
that the allocator would try really hard but there is no promise of a
success. This will work independent of the order and overrides the
default allocator behavior. Page allocator users have several levels of
guarantee vs. cost options (take GFP_KERNEL as an example)
- GFP_KERNEL & ~__GFP_RECLAIM - optimistic allocation without _any_
attempt to free memory at all. The most light weight mode which even
doesn't kick the background reclaim. Should be used carefully because
it might deplete the memory and the next user might hit the more
aggressive reclaim
- GFP_KERNEL & ~__GFP_DIRECT_RECLAIM (or GFP_NOWAIT)- optimistic
allocation without any attempt to free memory from the current
context but can wake kswapd to reclaim memory if the zone is below
the low watermark. Can be used from either atomic contexts or when
the request is a performance optimization and there is another
fallback for a slow path.
- (GFP_KERNEL|__GFP_HIGH) & ~__GFP_DIRECT_RECLAIM (aka GFP_ATOMIC) -
non sleeping allocation with an expensive fallback so it can access
some portion of memory reserves. Usually used from interrupt/bh
context with an expensive slow path fallback.
- GFP_KERNEL - both background and direct reclaim are allowed and the
_default_ page allocator behavior is used. That means that !costly
allocation requests are basically nofail but there is no guarantee of
that behavior so failures have to be checked properly by callers
(e.g. OOM killer victim is allowed to fail currently).
- GFP_KERNEL | __GFP_NORETRY - overrides the default allocator behavior
and all allocation requests fail early rather than cause disruptive
reclaim (one round of reclaim in this implementation). The OOM killer
is not invoked.
- GFP_KERNEL | __GFP_RETRY_MAYFAIL - overrides the default allocator
behavior and all allocation requests try really hard. The request
will fail if the reclaim cannot make any progress. The OOM killer
won't be triggered.
- GFP_KERNEL | __GFP_NOFAIL - overrides the default allocator behavior
and all allocation requests will loop endlessly until they succeed.
This might be really dangerous especially for larger orders.
Existing users of __GFP_REPEAT are changed to __GFP_RETRY_MAYFAIL
because they already had their semantic. No new users are added.
__alloc_pages_slowpath is changed to bail out for __GFP_RETRY_MAYFAIL if
there is no progress and we have already passed the OOM point.
This means that all the reclaim opportunities have been exhausted except
the most disruptive one (the OOM killer) and a user defined fallback
behavior is more sensible than keep retrying in the page allocator.
[akpm@linux-foundation.org: fix arch/sparc/kernel/mdesc.c]
[mhocko@suse.com: semantic fix]
Link: http://lkml.kernel.org/r/20170626123847.GM11534@dhcp22.suse.cz
[mhocko@kernel.org: address other thing spotted by Vlastimil]
Link: http://lkml.kernel.org/r/20170626124233.GN11534@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20170623085345.11304-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Alex Belits <alex.belits@cavium.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: NeilBrown <neilb@suse.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With gcc 4.1.2:
drivers/mmc/core/block.c: In function ‘mmc_blk_ioctl_cmd_issue’:
drivers/mmc/core/block.c:630: warning: ‘ioc_err’ may be used uninitialized in this function
Indeed, if mq_rq->ioc_count is zero, an uninitialized value will be
stored in mq_rq->drv_op_result and passed to blk_end_request_all().
Can mq_rq->ioc_count be zero?
- mmc_blk_ioctl_cmd() sets ioc_count to 1, so this is safe,
- mmc_blk_ioctl_multi_cmd() obtains ioc_count from user space in
response to the MMC_IOC_MULTI_CMD ioctl, and does allow zero.
To avoid returning an uninitialized value, and as it is pointless to do
all this work when the MMC_IOC_MULTI_CMD ioctl is used with zero
entries, check for this early in mmc_blk_ioctl_multi_cmd(), and return
zero, like was returned before.
Fixes: 3ecd8cf23f ("mmc: block: move multi-ioctl() to use block layer")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With gcc 4.1.2:
drivers/mmc/core/block.c: In function ‘mmc_blk_issue_drv_op’:
drivers/mmc/core/block.c:1178: warning: ‘ret’ may be used uninitialized in this function
Indeed, for MMC_DRV_OP_IOCTL, if mq_rq->ioc_count is zero, an
uninitialized value will be stored in mq_rq->drv_op_result and passed to
blk_end_request_all().
Can mq_rq->ioc_count be zero?
- mmc_blk_ioctl_cmd() sets ioc_count to 1, so this is safe,
- mmc_blk_ioctl_multi_cmd() obtains ioc_count from user space in
response to the MMC_IOC_MULTI_CMD ioctl, and does allow zero.
Initialize ret to zero to fix this for current and future callers.
Fixes: 0493f6fe5b ("mmc: block: Move boot partition locking into a driver op")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GPDwin uses PCI wifi which conflicts with SDIO's use of
acpi_device_fix_up_power() on child device nodes. Specifically
acpi_device_fix_up_power() causes the wifi module to get turned off.
Identifying GPDwin is problematic, but since SDIO is only used for wifi,
the presence of the PCI wifi card in the expected slot with an ACPI
companion node, is used to indicate that acpi_device_fix_up_power() should
be avoided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZWg0DAAoJEP4mhCVzWIwpyaUQAKpJl/QF5S8E4XaM+GKhhQfz
Af4EEGz/ySIJILCEe/A1W+xjTJh/n5jdTUTa197mDr136wp4UP8OUIhjtHHLY92E
Q74+piB77wSP0zeGFuDmtY/BRmMsXS2GOK1DlLovsDnThVNe5vZQgdXMTpx8Cfau
Bqea566L5EqGL4clOhYgmw3f9QVREDfqw2UahhrvTViSeJ2BZAYgl1lX/5YyX3vX
TIIrnSllGGTYTFTB+TLPsH6ac21IDJvagXySyMBUTVfHau9AXo8tDH+WbwfVYLwH
OmqmKaI6WT8z7oQy+WNC0P/r9GDRuqWAxdNPPF2PsRE+RbFeZVrBuN5brQxB+gMm
IJCA1z7RgLOoiu8tVOj30GXmmMM54NTkD2SLnsWG99Edh7jQ0gCVE8TGnFbgi7jl
8o/N1bB5fOeOMojgoFrTZmRKwIw1nPGFTehfiOzoll1BQy4CRqj7ZM8ji3THz11B
GrDMlbv+ocHRW9BVD0PNRUq+AVp5HRzV9actANArhhrHOwG/s9foVdEF+lVpSXty
M8PImSDrJ2bNi3aqbdkJ4IFMlAcrHw7m6mBlwTF7uCfRtcacbAy+cxYYCqNh+EOt
5l4qwbU1knH+IEEhgeSL0QQ8QNJcfR9fygifPovLN5Jo2yr0ZBMVD3wKPkZgOIJ2
Lsqoo2URLwa0uE2VU8Nm
=zJi3
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support"
* tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: dw_mmc: remove the unnecessary slot variable
mmc: dw_mmc: use the 'slot' instead of 'cur_slot'
mmc: dw_mmc: remove the 'id' arguments about functions relevant to slot
mmc: dw_mmc: change the array of slots
mmc: dw_mmc: remove the loop about finding slots
mmc: dw_mmc: deprecated the "num-slots" property
mmc: dw_mmc-rockchip: parse rockchip, desired-num-phases from DT
dt-bindings: rockchip-dw-mshc: add optional rockchip, desired-num-phases
mmc: renesas-sdhi: improve checkpatch cleanness
mmc: tmio: improve checkpatch cleanness
mmc: sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
mmc: slot-gpio: Add support to enable irq wake on cd_irq
mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
mmc: core: for data errors, take response of stop cmd into account
mmc: core: check also R1 response for stop commands
mmc: core: Clarify code for sending CSD
mmc: core: Drop mmc_all_send_cid() and use mmc_send_cxd_native() instead
mmc: core: Re-factor code for sending CID
mmc: core: Remove redundant code in mmc_send_cid()
mmc: core: Make mmc_can_reset() static
...
Pull core block/IO updates from Jens Axboe:
"This is the main pull request for the block layer for 4.13. Not a huge
round in terms of features, but there's a lot of churn related to some
core cleanups.
Note this depends on the UUID tree pull request, that Christoph
already sent out.
This pull request contains:
- A series from Christoph, unifying the error/stats codes in the
block layer. We now use blk_status_t everywhere, instead of using
different schemes for different places.
- Also from Christoph, some cleanups around request allocation and IO
scheduler interactions in blk-mq.
- And yet another series from Christoph, cleaning up how we handle
and do bounce buffering in the block layer.
- A blk-mq debugfs series from Bart, further improving on the support
we have for exporting internal information to aid debugging IO
hangs or stalls.
- Also from Bart, a series that cleans up the request initialization
differences across types of devices.
- A series from Goldwyn Rodrigues, allowing the block layer to return
failure if we will block and the user asked for non-blocking.
- Patch from Hannes for supporting setting loop devices block size to
that of the underlying device.
- Two series of patches from Javier, fixing various issues with
lightnvm, particular around pblk.
- A series from me, adding support for write hints. This comes with
NVMe support as well, so applications can help guide data placement
on flash to improve performance, latencies, and write
amplification.
- A series from Ming, improving and hardening blk-mq support for
stopping/starting and quiescing hardware queues.
- Two pull requests for NVMe updates. Nothing major on the feature
side, but lots of cleanups and bug fixes. From the usual crew.
- A series from Neil Brown, greatly improving the bio rescue set
support. Most notably, this kills the bio rescue work queues, if we
don't really need them.
- Lots of other little bug fixes that are all over the place"
* 'for-4.13/block' of git://git.kernel.dk/linux-block: (217 commits)
lightnvm: pblk: set line bitmap check under debug
lightnvm: pblk: verify that cache read is still valid
lightnvm: pblk: add initialization check
lightnvm: pblk: remove target using async. I/Os
lightnvm: pblk: use vmalloc for GC data buffer
lightnvm: pblk: use right metadata buffer for recovery
lightnvm: pblk: schedule if data is not ready
lightnvm: pblk: remove unused return variable
lightnvm: pblk: fix double-free on pblk init
lightnvm: pblk: fix bad le64 assignations
nvme: Makefile: remove dead build rule
blk-mq: map all HWQ also in hyperthreaded system
nvmet-rdma: register ib_client to not deadlock in device removal
nvme_fc: fix error recovery on link down.
nvmet_fc: fix crashes on bad opcodes
nvme_fc: Fix crash when nvme controller connection fails.
nvme_fc: replace ioabort msleep loop with completion
nvme_fc: fix double calls to nvme_cleanup_cmd()
nvme-fabrics: verify that a controller returns the correct NQN
nvme: simplify nvme_dev_attrs_are_visible
...
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
Remove the 'cur_slot'. Instead, just use 'slot'.
There is no multiple slots, so we need to consider only one slot.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Doesn't need to pass the id value for slot functions.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It doesn't need to use the array of slots anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dwmmc controller has used the only one slot.
It doesn't need to check the other slots.
Remove the loop about finding slots.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dwmmc controller is supporting only one slot per a IP.
Even though DWMMC IP is provided the multiple slot, but there is no
usage in real world.
In mmc subsystem, not allow the multiple slot concept.
Then "num-slots" property is deprecated.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.comi>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we unconditionally do tuning for each degree, which
costs 900ms for each boot and resume.
May someone argue that this is a question of accuracy VS time. But I
would say it's a trick of how we need to do decision for our boards.
If we don't care the time we spend at all, we could definitely do tuning
for each degree. But when we need to improve the user experience, for
instance, speed up resuming from S3, we should also have the right to
do that. This patch add parsing "rockchip,desired-num-phases", for folks
to specify the number of doing tuning. If not specified, 360 will be used
as before.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BLK_BOUNCE_ANY is the defauly now, so the call is superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add host capability MMC_CAP_CD_WAKE to enable irq wake on the card detect
irq.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP2_HC_ERASE_SZ is used only by a few mmc host drivers. Its intent
is to enable eMMC's high-capacity erase size, as to improve the behaviour
of the erase operations.
We should strive to avoid software configuration options that aren't
necessary, but instead deploy common behaviours. For these reasons, let's
remove the capability bit for MMC_CAP2_HC_ERASE_SZ and make it the default
behaviour.
Note that this change doesn't affect eMMCs supporting trim/discard, because
these commands operates on sectors and takes precedence over erase
commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Some errors are flagged only with the next command after a multiblock
transfer, e.g. ECC error. So, when checking for data transfer errors,
we check the result from the stop command as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To detect errors like ECC errors, we must parse the R1 response bits. Introduce
a helper function to also set the error value of a command when R1 error bits
are set. Add ECC error to list of flags checked. Use the new helper for the
stop command to call mmc_blk_recovery when detecting ECC errors which are only
flagged on the next command after multiblock.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make the code more consistent and to increase readability, add an
mmc_spi_send_csd() function, which gets called from mmc_send_csd() in case
of SPI mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Instead of having the caller to check for SPI mode, let's leave that to
internals of mmc_send_cid(). In this way the code gets cleaner and it
becomes clear what is specific to SPI and non-SPI mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_send_cid() is never called using non SPI mode. Thus, let's remove
the redundant code dealing with this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_flush_cache() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_interrupt_hpi() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear. The move also enables us to make
mmc_send_hpi_cmd() static, so let's do that change as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start_bkops(), mmc_stop_bkops() and mmc_read_bkops_status()
functions are all specific to eMMCs. To make this clear, let's move them
from from core.c to mmc_ops.c and take the opportunity to make
mmc_read_bkops_status() static.
While moving them, get rid of MMC_BKOPS_MAX_TIMEOUT (4 min) and use the
common default timeout MMC_OPS_TIMEOUT_MS (10 min) instead, as there is no
need to have specific default timeout for bkops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start|stop_bkops(), mmc_read_bkops_status() and mmc_interrupt_hpi()
functions are all used from within the mmc core module, thus there are no
need to use EXPORT_SYMBOL() for them, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
In preparation for using the generic mmc binding for io regulator
("vqmmc"), use mmc_regulator_get_supply() to get vmmc and vqmmc regulators.
Only if "vqmmc" regulator isn't found, fallback to use "vmmc_aux"
regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Do not initialize MMC regulators to NULL on error in omap_hsmmc driver
similar to what is done in mmc_regulator_get_supply(). This is in
preparation for using mmc_regulator_get_supply() to get MMC
regulators.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers core will runtime suspend a device with no driver. That means the
SDIO card will be runtime suspended as soon as it is added. It is then
runtime resumed to add each function. That is entirely pointless, so add
pm runtime get/put to keep the SDIO card runtime resumed until the function
devices have been added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path deletes the device by calling mmc_sdio_remove() which must
be called without the host claimed. Simplify the error path so it does just
that and add a comment about why we don't disable runtime PM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add PCI ids and enhanced strobe support for Intel CNP. This is combined
with GLK due to the pending CMDQ support which they both share.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update copyrights to reflect work by Wolfram Sang and myself since last
year.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use EXPORT_SYMBOL_GPL rather than the non _GPL variant as there seems to be
no reason not to.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The acpi-subsys already calls acpi_bus_get_status() and checks that
device->status.present is set before even registering the platform_device
so out probe function will never get called if device->status.present is
false and there is no need for this check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To achieve that, we set the registers in the generic HW reset routine
which gets called at both, init and resume. We also make sure to move
SDIO initialization before reset gets called in probe().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch applies customized PCI_DEVICE_ macros to specify the pci_ids
instead of open-coding them within the sdhci-pci driver.
By introducing device specific macros the pci_ids table becomes much
shorter and easier to comprehend than it would be possible using the
generic version of the PCI_DEVICE_ macros.
Signed-off-by: Matthias Kraemer <matthiasmartinsson@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the
ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers
(300 kB/s on average), and this erratum actually does not imply that
multiple-block transfers are not supported, so this was overkill.
The suggested workaround for this erratum is to set SYSCTL.RSTA, but the
simple DAT line software reset (which resets the DMA circuit among
others) triggered by sdhci_finish_data() in case of errors seems to be
sufficient. Indeed, generating errors in a controlled manner on i.MX25
using the FEVT register right in the middle of read data transfers
without this quirk shows that nothing is written to the buffer by the
eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so
the data transfers on AHB are properly aborted. For write data
transfers, neither extra data nor extra Auto CMD12 is sent, as expected.
Moreover, after intensive stress tests on i.MX25, removing
SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe.
SDHCI_QUIRK_BROKEN_ADMA has nothing to do with ENGcm07207, so set
ESDHC_FLAG_ERR004536 for the devices that had ESDHC_FLAG_ENGCM07207 set
in order to continue getting SDHCI_QUIRK_BROKEN_ADMA.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD
clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC.
The previous minimum prescaler value of 2 in SDR mode with the eSDHC was
a code remnant from PowerPC, which actually has this limitation on
earlier revisions.
In DDR mode, the prescaler can divide by up to 512.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On i.MX25, the eSDHC DAT line software reset (SYSCTL.RSTD) unexpectedly
clears at least the data transfer width (PROCTL.DTW), which then results
in data CRC errors. This behavior is not documented, but it has actually
been observed. Consequently, the DAT line software resets triggered by
sdhci.c in case of errors caused unrecoverable errors.
Fix this by making sure that the DAT line software reset does not alter
the Host Control register. This behavior being undocumented, it may also
be present on other i.MX SoCs, so apply this fix for the whole i.MX
family.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC can only DMA from 32-bit-aligned addresses.
This fixes the following test cases of mmc_test:
11: Badly aligned write
12: Badly aligned read
13: Badly aligned multi-block write
14: Badly aligned multi-block read
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix various English mistakes and typos in comments and in printed
strings.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Null check at line 1165: if (mrq->cmd), implies that mrq->cmd might
be NULL.
Add null checks before dereferencing pointer mrq->cmd in order to avoid
any potential NULL pointer dereference.
Addresses-Coverity-ID: 1408740
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows mmc drivers to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows the dw_mmc driver to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only reason to why the mmc block device driver needs to implements its
own version of how to get the status of the card, is that it needs to
specify a different amount of retries.
Therefore add a new exported function which allows the caller to specify
the number of retries and convert everybody to use it, as this simplifies
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This moves the boot partition lock command (issued from sysfs)
into a custom block layer request, just like the ioctl()s,
getting rid of yet another instance of mmc_get_card().
Since we now have two operations issuing special DRV_OP's, we
rename the result variable ->drv_op_result.
Tested by locking the boot partition from userspace:
> cd /sys/devices/platform/soc/80114000.sdi4_per2/mmc_host/mmc3/
mmc3:0001/block/mmcblk3/mmcblk3boot0
> echo 1 > ro_lock_until_next_power_on
[ 178.645324] mmcblk3boot1: Locking boot partition ro until next power on
[ 178.652221] mmcblk3boot0: Locking boot partition ro until next power on
Also tested this with a huge dd job in the background: it
is now possible to lock the boot partitions on the card even
under heavy I/O.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need to access static functions above the pure block layer
operations in the file, so move the driver operations issue
function down so we can see all non-blocklayer symbols.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will expand the DRV_OP usage, so we need to know which
operation we're performing. Tag the operations with an
enum:ed type and rename the function so it is clear that
it deals with any command and put a switch statement in
it. Currently only ioctls are supported.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just as we can use blk_mq_rq_from_pdu() to get the per-request
tag we can use blk_mq_rq_to_pdu() to get a request from a tag.
Introduce a static inline helper so we are on the clear what
is happening.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Plain code move with no changes. Needed for refactoring. Also, looks
nicer if request and finish_request are next to each other.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The obviously wrong comment was added in 2011 with commit df3ef2d3c9
("mmc: protect the tmio_mmc driver against a theoretical race") but
already obsoleted half a year later with commit b9269fdd4f ("mmc:
tmio: fix recursive spinlock, don't schedule with interrupts disabled").
Fixes: b9269fdd4f ("mmc: tmio: fix recursive spinlock, don't schedule with interrupts disabled")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Split handling mrq into a seperate function. We need to call it from
another place soon.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This part confused me and I had to read it twice until I got it. Let's
follow the standard pattern to bail out if something is wrong and keep
in the body of the function when everything is as expected.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit cdf8a6fb48
"mmc: block: Introduce queue semantics"
deleted the last user of mmc_req_is_special() and it was
a horrible hack to classify requests as "special" or
"not special" to begin with, so delete the helper.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches also the multiple-command ioctl() call to issue
all ioctl()s through the block layer instead of going directly
to the device.
We extend the passed argument with an argument count and loop
over all passed commands in the ioctl() issue function called
from the block layer.
By doing this we are again loosening the grip on the big host
lock, since two calls to mmc_get_card()/mmc_put_card() are
removed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Avri Altman <Avri.Altman@sandisk.com>
This wraps single ioctl() commands into block requests using
the custom block layer request types REQ_OP_DRV_IN and
REQ_OP_DRV_OUT.
By doing this we are loosening the grip on the big host lock,
since two calls to mmc_get_card()/mmc_put_card() are removed.
We are storing the ioctl() in/out argument as a pointer in
the per-request struct mmc_blk_request container. Since we
now let the block layer allocate this data, blk_get_request()
will allocate it for us and we can immediately dereference
it and use it to pass the argument into the block layer.
We refactor the if/else/if/else ladder in mmc_blk_issue_rq()
as part of the job, keeping some extra attention to the
case when a NULL req is passed into this function and
making that pipeline flush more explicit.
Tested on the ux500 with the userspace:
mmc extcsd read /dev/mmcblk3
resulting in a successful EXTCSD info dump back to the
console.
This commit fixes a starvation issue in the MMC/SD stack
that can be easily provoked in the following way by
issueing the following commands in sequence:
> dd if=/dev/mmcblk3 of=/dev/null bs=1M &
> mmc extcs read /dev/mmcblk3
Before this patch, the extcsd read command would hang
(starve) while waiting for the dd command to finish since
the block layer was holding the card/host lock.
After this patch, the extcsd ioctl() command is nicely
interpersed with the rest of the block commands and we
can issue a bunch of ioctl()s from userspace while there
is some busy block IO going on without any problems.
Conversely userspace ioctl()s can no longer starve
the block layer by holding the card/host lock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Avri Altman <Avri.Altman@sandisk.com>
The variable is_rpmb is clearly a bool and even assigned true
and false, yet declared as an int.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_queue_req is a per-request state container the MMC core uses
to carry bounce buffers, pointers to asynchronous requests and so on.
Currently allocated as a static array of objects, then as a request
comes in, a mmc_queue_req is assigned to it, and used during the
lifetime of the request.
This is backwards compared to how other block layer drivers work:
they usally let the block core provide a per-request struct that get
allocated right beind the struct request, and which can be obtained
using the blk_mq_rq_to_pdu() helper. (The _mq_ infix in this function
name is misleading: it is used by both the old and the MQ block
layer.)
The per-request struct gets allocated to the size stored in the queue
variable .cmd_size initialized using the .init_rq_fn() and
cleaned up using .exit_rq_fn().
The block layer code makes the MMC core rely on this mechanism to
allocate the per-request mmc_queue_req state container.
Doing this make a lot of complicated queue handling go away. We only
need to keep the .qnct that keeps count of how many request are
currently being processed by the MMC layer. The MQ block layer will
replace also this once we transition to it.
Doing this refactoring is necessary to move the ioctl() operations
into custom block layer requests tagged with REQ_OP_DRV_[IN|OUT]
instead of the custom code using the BigMMCHostLock that we have
today: those require that per-request data be obtainable easily from
a request after creating a custom request with e.g.:
struct request *rq = blk_get_request(q, REQ_OP_DRV_IN, __GFP_RECLAIM);
struct mmc_queue_req *mq_rq = req_to_mq_rq(rq);
And this is not possible with the current construction, as the request
is not immediately assigned the per-request state container, but
instead it gets assigned when the request finally enters the MMC
queue, which is way too late for custom requests.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf: Folded in the fix to drop a call to blk_cleanup_queue()]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
This option is activated by all multiplatform configs and what
not so we almost always have it turned on, and the memory it
saves is negligible, even more so moving forward. The actual
bounce buffer only gets allocated only when used, the only
thing the ifdefs are saving is a little bit of code.
It is highly improper to have this as a Kconfig option that
get turned on by Kconfig, make this a pure runtime-thing and
let the host decide whether we use bounce buffers. We add a
new property "disable_bounce" to the host struct.
Notice that mmc_queue_calc_bouncesz() already disables the
bounce buffers if host->max_segs != 1, so any arch that has a
maximum number of segments higher than 1 will have bounce
buffers disabled.
The option CONFIG_MMC_BLOCK_BOUNCE is default y so the
majority of platforms in the kernel already have it on, and
it then gets turned off at runtime since most of these have
a host->max_segs > 1. The few exceptions that have
host->max_segs == 1 and still turn off the bounce buffering
are those that disable it in their defconfig.
Those are the following:
arch/arm/configs/colibri_pxa300_defconfig
arch/arm/configs/zeus_defconfig
- Uses MMC_PXA, drivers/mmc/host/pxamci.c
- Sets host->max_segs = NR_SG, which is 1
- This needs its bounce buffer deactivated so we set
host->disable_bounce to true in the host driver
arch/arm/configs/davinci_all_defconfig
- Uses MMC_DAVINCI, drivers/mmc/host/davinci_mmc.c
- This driver sets host->max_segs to MAX_NR_SG, which is 16
- That means this driver anyways disabled bounce buffers
- No special action needed for this platform
arch/arm/configs/lpc32xx_defconfig
arch/arm/configs/nhk8815_defconfig
arch/arm/configs/u300_defconfig
- Uses MMC_ARMMMCI, drivers/mmc/host/mmci.[c|h]
- This driver by default sets host->max_segs to NR_SG,
which is 128, unless a DMA engine is used, and in that case
the number of segments are also > 1
- That means this driver already disables bounce buffers
- No special action needed for these platforms
arch/arm/configs/sama5_defconfig
- Uses MMC_SDHCI, MMC_SDHCI_PLTFM, MMC_SDHCI_OF_AT91, MMC_ATMELMCI
- Uses drivers/mmc/host/sdhci.c
- Normally sets host->max_segs to SDHCI_MAX_SEGS which is 128 and
thus disables bounce buffers
- Sets host->max_segs to 1 if SDHCI_USE_SDMA is set
- SDHCI_USE_SDMA is only set by SDHCI on PCI adapers
- That means that for this platform bounce buffers are already
disabled at runtime
- No special action needed for this platform
arch/blackfin/configs/CM-BF533_defconfig
arch/blackfin/configs/CM-BF537E_defconfig
- Uses MMC_SPI (a simple MMC card connected on SPI pins)
- Uses drivers/mmc/host/mmc_spi.c
- Sets host->max_segs to MMC_SPI_BLOCKSATONCE which is 128
- That means this platform already disables bounce buffers at
runtime
- No special action needed for these platforms
arch/mips/configs/cavium_octeon_defconfig
- Uses MMC_CAVIUM_OCTEON, drivers/mmc/host/cavium.c
- Sets host->max_segs to 16 or 1
- Setting host->disable_bounce to be sure for the 1 case
arch/mips/configs/qi_lb60_defconfig
- Uses MMC_JZ4740, drivers/mmc/host/jz4740_mmc.c
- This sets host->max_segs to 128 so bounce buffers are
already runtime disabled
- No action needed for this platform
It would be interesting to come up with a list of the platforms
that actually end up using bounce buffers. I have not been
able to infer such a list, but it occurs when
host->max_segs == 1 and the bounce buffering is not explicitly
disabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make renesas_sdhi_sys_dmac.c a top-level module file that makes use of
library code supplied by renesas_sdhi_core.c
This is in order to facilitate adding other variants of SDHI;
in particular SDHI using different DMA controllers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Arnd: Fixed module build error]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.
Internal symbols have also been renamed to reflect the filename change.
The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename the source file for DMA for SDHI as a follow-up to attaching
DMA code to the SDHI driver rather than the tmio_core driver.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
The name sys_dmac was chosen to reflect the type of DMA used.
Internal symbols have also been renamed to reflect the filename change.
A follow-up patch will re-organise the SDHI driver removing
the need for renesas_sdhi_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename tmio_mmc_pio.c to tmio_mmc_core.c to more accurately reflect its
function: to provide core code for the tmio-mmc and sh-mobole-sdhi drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor DMA support to allow it to be provided by a set of call-backs
that are provided by a host driver. The motivation is to allow multiple
DMA implementations to be provided and instantiated at run-time.
Instantiate the existing DMA implementation from the sh_mobile_sdhi driver
which appears to match the current use-case. This has the side effect
of moving the DMA code from the tmio_core to the sh_mobile_sdhi driver.
A follow-up patch will change the source file for the SDHI DMA
implementation accordingly. Another follow-up patch will re-organise the
SDHI driver removing the need for tmio_mmc_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reshuffle the comment at the top of the source
dropping filenames and moving up human readable strings.
This seems to be somewhat more useful information to start the
source file with. It is also less fragile, f.e. to file renames.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a6db2c8603 ("mmc: dw_mmc: Don't allow Runtime PM for
SDIO cards")'
As dw_mmc now is capable of preventing runtime PM suspend while SDIO IRQs
are enabled, let's drop the less fine-grained method, which is preventing
runtime PM suspend for all SDIO cards - no matter of whether SDIO IRQs are
being enabled or not.
In this way we don't keep the host runtime PM resumed, unless it's really
needed, thus avoiding to waste power.
Especially when SDIO IRQs is supported via a separate out-of-band IRQ line,
which isn't defined by the SDIO standard, typically the SDIO func driver
doesn't enable SDIO IRQs via sdio_claim_irq(). So, for these cases we can
now allow the dwmmc device to be runtime PM suspended in-between requests.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
To be able to handle SDIO IRQs the dw_mmc device needs to be powered and
providing clock to the SDIO card. Therefore, we must not allow the device
to be runtime PM suspended while SDIO IRQs are enabled.
To fix this, let's increase the runtime PM usage count while the mmc core
enables SDIO IRQs. Later when the mmc core tells dw_mmc to disable SDIO
IRQs, we drop the usage count to again allow runtime PM suspend.
This now becomes the default behaviour for dw_mmc. In cases where SDIO IRQs
can be re-routed as GPIO wake-ups during runtime PM suspend, one could
potentially allow runtime PM suspend. However, that will have to be
addressed as a separate change on top of this one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Convert to use the more lightweight method for processing SDIO IRQs, which
involves the following changes:
- Enable MMC_CAP2_SDIO_IRQ_NOTHREAD when SDIO IRQ is supported and use
sdio_signal_irq() instead of mmc_signal_sdio_irq().
- Mask the SDIO IRQ before signaling a new one to be processed.
- Implement the ->ack_sdio_irq() callback to unmask the SDIO IRQ.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
For hosts not supporting MMC_CAP2_SDIO_IRQ_NOTHREAD but MMC_CAP_SDIO_IRQ,
the SDIO IRQs are processed from a dedicated kernel thread. For these
cases, the host calls mmc_signal_sdio_irq() from its ISR to signal a new
SDIO IRQ.
Signaling an SDIO IRQ makes the host's ->enable_sdio_irq() callback to be
invoked to temporary disable the IRQs, before the kernel thread is woken up
to process it. When processing of the IRQs are completed, they are
re-enabled by the kernel thread, again via invoking the host's
->enable_sdio_irq().
The observation from this, is that the execution path is being unnecessary
complex, as the host driver already knows that it needs to temporary
disable the IRQs before signaling a new one. Moreover, replacing the kernel
thread with a work/workqueue would not only greatly simplify the code, but
also make it more robust.
To address the above problems, let's continue to build upon the support for
MMC_CAP2_SDIO_IRQ_NOTHREAD, as it already implements SDIO IRQs to be
processed without using the clumsy kernel thread and without the ping-pong
calls of the host's ->enable_sdio_irq() callback for each processed IRQ.
Therefore, let's add new API sdio_signal_irq(), which enables hosts to
signal/process SDIO IRQs by using a work/workqueue, rather than using the
kernel thread.
Add also a new host callback ->ack_sdio_irq(), which the work invokes when
the SDIO IRQs have been processed. This informs the host about when it
shall re-enable the SDIO IRQs. Potentially, we could re-use the existing
->enable_sdio_irq() callback instead of adding a new one, however it has
turned out that it's more convenient for hosts to get this information via
a separate callback.
Hosts that wants to use this new method to signal/process SDIO IRQs, must
enable MMC_CAP2_SDIO_IRQ_NOTHREAD and implement the ->ack_sdio_irq()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In cases when MMC_CAP2_SDIO_IRQ_NOTHREAD is set, there is a minor window
for when the mmc host could call sdio_run_irqs(), while in fact an SDIO
func driver could have decided to released the SDIO IRQ via a call to
sdio_release_irq(). In this scenario, processing of the SDIO IRQs are done
even if there is none IRQ claimed, which is not what we want.
To prevent this from happen, close the window by validating that at least
one SDIO IRQs is claimed, before deciding to process them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In case if a pwrseq-emmc has been bound to the host, a call to
mmc_power_up() triggers an eMMC HW reset via the pwrseq_emmc's
->post_power_on() callback. This isn't really what we want, as
mmc_power_up() is called each time when resuming the card.
As a matter of fact, the current approach may also violate the eMMC spec,
as the involved delays managed in pwrseq_emmc assumes both VCC and VCCQ has
been turned on, which isn't the case for VCCQ, unless the regulator is
always on.
Fix this behaviour by aligning to the same procedure used when the mmc host
implements the ->hw_reset() callback and has the MMC_CAP_HW_RESET flag set.
In this way the eMMC HW reset is issued at card detection scan, to cope
with bogus bootloaders and in the error recovery path via the mmc specific
bus_ops->reset() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The ->reset() callback is needed to implement a better support for eMMC HW
reset. The following changes will take advantage of the new callback.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add the missing endianness conversions when printing the USB
device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the end of either of the read or write loops len is always zero
and hence the non-zero check on len and return of -EIO is redundant
and can be removed.
Detected by CoverityScan, CID#114293 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ret is signed however is printed as unsigned fix the same.
If printed as a negative number the result is easier to read.
No functional change.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The guid intel_dsm_guid does not need to be in global scope, so make it
static.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There have been reports about SDIO failing with certain WiFi chips in
descriptor chain mode. SD / eMMC are working fine.
So let's fall back to bounce buffer mode for command SD_IO_RW_EXTENDED.
This was reported to fix the error.
Fixes: 79ed05e329 "mmc: meson-gx: add support for descriptor chain mode"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we use nornal Linux errno values in the block layer, and while
we accept any error a few have overloaded magic meanings. This patch
instead introduces a new blk_status_t value that holds block layer specific
status codes and explicitly explains their meaning. Helpers to convert from
and to the previous special meanings are provided for now, but I suspect
we want to get rid of them in the long run - those drivers that have a
errno input (e.g. networking) usually get errnos that don't know about
the special block layer overloads, and similarly returning them to userspace
will usually return somethings that strictly speaking isn't correct
for file system operations, but that's left as an exercise for later.
For now the set of errors is a very limited set that closely corresponds
to the previous overloaded errno values, but there is some low hanging
fruite to improve it.
blk_status_t (ab)uses the sparse __bitwise annotations to allow for sparse
typechecking, so that we can easily catch places passing the wrong values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Hikey board. Together with a couple of DTS updates for the Hikey board we have
also extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence for the
WiFi chip.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ECeh
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
board.
Together with a couple of DTS updates for the Hikey board we have also
extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence
for the WiFi chip"
* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
arm64: dts: hikey: Fix WiFi support
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
arm64: dts: hikey: Add clock for the pmic mfd
mfd: dts: hi655x: Add clock binding for the pmic
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
mmc: dt: pwrseq-simple: Invent power-off-delay-us
