All length fields in Linux I2C are u16, so a HW length limitation of 16
bit lengths is not a limitation. Remove the quirk structure.
Tested-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BSC data buffers to send and receive data are each of size 32 bytes
or 8 bytes 'xfersz' depending on SoC. The problem observed for all the
combined message transfer was if length of data transfer was a multiple
of 'xfersz' a repeated START was being transmitted by BSC driver. Fixed
this by appropriately setting START/STOP conditions for such transfers.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Refcount of of_node is increased with of_node_get() in i2c_mux_add_adapter().
It must be decreased with of_node_put() in i2c_mux_del_adapters().
Signe-off-by: Qi Hou <qi.hou@windriver.com>
Reviewed-by: Zhang Xiao <xiao.zhang@windriver.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While modifying the driver to use the STOP interrupt, the completion of the
intermediate transfers need to wake the driver back up in order to initiate
the next transfer (restart condition). Otherwise you get never ending
interrupts and only the first transfer sent.
Fixes: 71ccea095e ("i2c: riic: correctly finish transfers")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Refcount of of_node is increased with of_node_get() in i2c_mux_add_adapter().
It must be decreased with of_node_put() in i2c_mux_del_adapters().
Cc: stable@vger.kernel.org
Signed-off-by: Qi Hou <qi.hou@windriver.com>
Reviewed-by: Zhang Xiao <xiao.zhang@windriver.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Acquire P-Unit access to stop others from accessing the P-Unit while the
PMIC i2c bus is in use. This is necessary because accessing the P-Unit
from the kernel may result in the P-Unit trying to access the PMIC i2c
bus, which results in a hang when it happens while we own the PMIC i2c
bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=155241
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: tagorereddy <tagore.chandan@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-10-hdegoede@redhat.com
The cherrytrail punit has the pmic i2c bus access semaphore at a
different register address.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-9-hdegoede@redhat.com
Use iosf_mbi_modify instead of iosf_mbi_read + iosf_mbi_write so that
we keep the iosf_mbi_lock locked during the read-modify-write done to
reset the semaphore.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-8-hdegoede@redhat.com
On my cherrytrail tablet with axp288 pmic, just doing a bunch of repeated
reads from the pmic, e.g. "i2cdump -y 14 0x34" would lookup the tablet in
1 - 3 runs guaranteed.
This seems to be causes by the cpu trying to enter C6 or C7 while we hold
the punit bus semaphore, at which point everything just hangs.
Avoid this by disallowing the CPU to enter C6 or C7 before acquiring the
punit bus semaphore.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-7-hdegoede@redhat.com
If (!shared_host) simply return 0, this avoids delaying the probe if
iosf_mbi_available() returns false when an i2c bus is not using the
punit semaphore.
Also move the if (!iosf_mbi_available()) check to above the
dev_info, so that we do not repeat the dev_info on every probe
until iosf_mbi_available() returns true.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-6-hdegoede@redhat.com
Pass dw_i2c_dev into the helper functions, this is a preparation patch
for the punit semaphore fixes done in the other patches in this set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-5-hdegoede@redhat.com
Rename accessor_flags to flags, so that we can use the field for
other flags too. This is a preparation patch for adding cherrytrail
support to the punit semaphore code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-4-hdegoede@redhat.com
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has for you two new drivers (Tegra BPMP and STM32F4), interrupt
support for pca954x muxes, and a bunch of driver bugfixes and
improvements. Nothing really special this cycle.
A few commits have been added to my tree just recently. Those are the
Tegra BPMP driver and a few straightforward bugfixes or cleanups which
I prefer to have upstream rather soonish. The rest had proper
linux-next exposure"
* 'i2c/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (25 commits)
i2c: thunderx: Replace pci_enable_msix()
i2c: exynos5: fix arbitration lost handling
i2c: exynos5: disable fifo-almost-empty irq signal when necessary
i2c: at91: ensure state is restored after suspending
i2c: bcm2835: Avoid possible NULL ptr dereference
i2c: Add Tegra BPMP I2C proxy driver
dt-bindings: Add Tegra186 BPMP I2C binding
misc: eeprom: at24: use device_property_*() functions instead of of_get_property()
i2c: mux: pca954x: Add interrupt controller support
dt: bindings: i2c-mux-pca954x: Add documentation for interrupt controller
i2c: mux: pca954x: Add missing pca9542 definition to chip_desc
i2c: riic: correctly finish transfers
i2c: i801: Add support for Intel Gemini Lake
i2c: mux: pca9541: Export OF device ID table as module aliases
i2c: mux: pca954x: Export OF device ID table as module aliases
i2c: mux: mlxcpld: remove unused including <linux/version.h>
i2c: busses: constify i2c_algorithm structures
i2c: i2c-mux-gpio: rename i2c-gpio-mux to i2c-mux-gpio
i2c: sh_mobile: document support for r8a7796 (R-Car M3-W)
i2c: i2c-cros-ec-tunnel: Reduce logging noise
...
Using pci_alloc_irq_vectors() instead of the deprecated
pci_enable_msix() allows to remove the msix_entry from
struct octeon_i2c and thus to get rid of the config symbol check.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of arbitration lost adequate interrupt sometimes is not signaled.
As a result transfer timeouts and is not retried, as it should. To avoid
such cases code is added to check transaction status in case of every
interrupt.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fifo-almost-empty irq signal should be disabled as soon as possible,
to avoid unnecessary interrupt storm. The best moment is when there is
no more data to feed fifo.
This patch fixes system stalls caused by IRQ storm.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow built-in (static) device properties to be declared
as constant, make it possible to save memory by discarding
alternative (but unused) built-in (static) property sets and
add support for automatic handling of built-in properties
to the I2C code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+P7T
-----END PGP SIGNATURE-----
Merge tag 'device-properties-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device property updates from Rafael J. Wysocki:
"Generic device properties framework updates for v4.11-rc1
Allow built-in (static) device properties to be declared as constant,
make it possible to save memory by discarding alternative (but unused)
built-in (static) property sets and add support for automatic handling
of built-in properties to the I2C code"
* tag 'device-properties-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
i2c: allow specify device properties in i2c_board_info
device property: export code duplicating array of property entries
device property: constify property arrays values
device property: allow to constify properties
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
* Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng).
* ACPI resources handling fix related to invalid resource
descriptors (Bob Moore).
* Fix to enable implicit result conversion for several ASL
library functions (Bob Moore).
* Support for method invocations as target operands in AML
(Bob Moore).
* Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore).
* Utilities updates (Bob Moore, Lv Zheng).
* Disassembler/debugger updates (David Box, Lv Zheng).
* Build fixes (Colin Ian King, Lv Zheng).
* Update of copyright notices in all files (Bob Moore).
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan).
- Fixes for the ACPI EC and button drivers (Lv Zheng).
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov).
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui).
- Message formatting fix for the ACPI APEI code (Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aJJ+
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170119, which among other things updates copyright notices in all of
the ACPICA files, fix a couple of issues in the ACPI EC and button
drivers, fix modalias handling for non-discoverable devices with
DT-compatible identification strings, add a suspend quirk for one
platform and fix a message in the APEI code.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
+ Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng)
+ ACPI resources handling fix related to invalid resource
descriptors (Bob Moore)
+ Fix to enable implicit result conversion for several ASL library
functions (Bob Moore)
+ Support for method invocations as target operands in AML (Bob
Moore)
+ Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore)
+ Utilities updates (Bob Moore, Lv Zheng)
+ Disassembler/debugger updates (David Box, Lv Zheng)
+ Build fixes (Colin Ian King, Lv Zheng)
+ Update of copyright notices in all files (Bob Moore)
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan)
- Fixes for the ACPI EC and button drivers (Lv Zheng)
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov)
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui)
- Message formatting fix for the ACPI APEI code (Colin Ian King)"
* tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Update version to 20170119
ACPICA: Tools: Update common signon, remove compilation bit width
ACPICA: Source tree: Update copyright notices to 2017
ACPICA: Linuxize: Restore and fix Intel compiler build
x86/ACPI: keep x86_cpu_to_acpiid mapping valid on CPU hotplug
spi: acpi: Initialize modalias from of_compatible
i2c: acpi: Initialize info.type from of_compatible
ACPI / bus: Introduce acpi_of_modalias() equiv of of_modalias_node()
ACPI: save NVS memory for Lenovo G50-45
ACPI, APEI, EINJ: fix malformed newline escape
ACPI / button: Remove lid_init_state=method mode
ACPI / button: Change default behavior to lid_init_state=open
ACPI / EC: Use busy polling mode when GPE is not enabled
ACPI / EC: Remove old CLEAR_ON_RESUME quirk
ACPICA: Update version to 20161222
ACPICA: Parser: Update parse info table for some operators
ACPICA: Fix a problem with recent extra support for control method invocations
ACPICA: Parser: Allow method invocations as target operands
ACPICA: Fix for implicit result conversion for the ToXXX functions
ACPICA: Resources: Not a valid resource if buffer length too long
..
When going to suspend, the I2C registers may be lost because the power to
VDDcore is cut. Restore them when resuming.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit e247454103 ("bcm2835: Fix hang for writing messages
larger than 16 bytes") the interrupt handler is prone to a possible
NULL pointer dereference. This could happen if an interrupt fires
before curr_msg is set by bcm2835_i2c_xfer_msg() and randomly occurs
on the RPi 3. Even this is an unexpected behavior the driver must
handle that with an error instead of a crash.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: e247454103 ("bcm2835: Fix hang for writing messages larger than 16 bytes")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Tegra BPMP I2C driver. The BPMP is the boot and power management
processor embedded in Tegra SoCs. In newer SoC versions, access to one
of the I2C busses goes via the BPMP, requiring a different "proxy" I2C
driver that accesses the bus via the real I2C driver embedded in the
BPMP firmware.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Various muxes can aggregate multiple interrupts from each i2c bus.
All of the muxes with interrupt support combine the active low irq lines
using an internal 'and' function and generate a combined active low
output. The muxes do provide the ability to read a control register to
determine which irq is active. By making the mux an irq controller isr
latency can potentially be reduced by reading the status register and
then only calling the registered isr on that bus segment.
As there is no irq masking on the mux irq are disabled until irq_unmask is
called at least once.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Peter Rosin <peda@axentia.se>
The spec for the pca954x was missing. This chip is the same as the pca9540
except that it has interrupt lines. While the i2c_device_id table mapped
the pca9542 to the pca9540 definition the compatible table did not. In
preparation for irq support add the pca9542 definition.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Peter Rosin <peda@axentia.se>
This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.
At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.
Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.
This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.
Fixes: 310c18a414 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Gemini Lake has the same SMBus host controller than Intel Broxton.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid
multiple buses accessing to the semaphore at the same time.
Fixes: 701dc207bf ("i2c: piix4: Avoid race conditions with IMC")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since '701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")' we
are using the SMBSLVCNT register at offset 0x8. We need to request it.
Fixes: 701dc207bf ("i2c: piix4: Avoid race conditions with IMC")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declare i2c_algorithm structures as const as they are only stored in the
algo field of an i2c_adapter structure. This field is of type const, so
i2c_algorithm structures having this property can be made const too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> for
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With many drivers converting to using generic device properties, it is
useful to provide array of device properties when instantiating new i2c
client via i2c_board_info and have them automatically added to the device
in question.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When using devicetree i2c_board_info.type is set to the compatible
string with the vendor prefix removed. For I2C devices described via
ACPI the i2c_board_info.type string is set to the ACPI device name. When
using ACPI and DT ids this string ends up something like "PRP0001:00".
If the of_compatible property is present try to use that instead. This
makes it easier to instantiate i2c drivers through ACPI with DT ids.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If an i2c access through i2c-cros-ec-tunnel returns an error, the following
log message is seen on the console.
cros-ec-i2c-tunnel ff200000.spi:ec@0:i2c-tunnel:
Error parsing EC i2c message -121
This can happen a lot if, for example, the i2c-detect command is executed.
Since it is perfectly normal for an i2c controller to report an error,
drop the message. Also, report -ENXIO instead of -EREMOTEIO if the access
error is due to NAK from the device, and return -EIO instead of -EREMOTEIO
for other errors, as suggested in Documentation/i2c/fault-codes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This function has the purpose of mode detection by checking the
device nodes for a reg matching with the I2C_OWN_SLAVE_ADDREESS flag.
Currently only checks using OF functions (ACPI slave not supported yet).
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When system enters VLLS mode, module power is turned off. As a result,
all registers are reset to HW default value. After exiting VLLS mode,
registers are still in default mode. As a result, the pinctrl settings
are incorrect, which will affect the module function.
The patch recovers the pinctrl setting when exit VLLS mode.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
[wsa: added missing include]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit implements suspend/resume support in the mv64xxx I2C
controller driver. There is no need to implement a ->suspend() hook, as
calling mv64xxx_i2c_hw_init() at ->resume() time is enough.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Lior Amsalem <alior@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
[Thomas: switch to dev_pm_ops, fix build warning when !PM.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the STM32F4 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cadence I2C driver calls cdns_i2c_writereg(..) to setup a workaround
in the controller, but did so after calling i2c_add_adapter() which starts
probing devices on the bus. Change the order so that the configuration is
completely finished before using the adapter.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On AMD's SB800 and upwards, the SMBus is shared with the Integrated
Micro Controller (IMC).
The platform provides a hardware semaphore to avoid race conditions
among them. (Check page 288 of the SB800-Series Southbridges Register
Reference Guide http://support.amd.com/TechDocs/45482.pdf)
Without this patch, many access to the SMBus end with an invalid
transaction or even with the bus stalled.
Reported-by: Alexandre Desnoyers <alex@qtec.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>:
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fix to spelling mistake in WARN message, insufficient has
an insufficient number of i's in the spelling.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In of_i2c_register_device(), when the check for
device address validity fails we print the info.addr,
which has not been assigned properly.
Fix this by printing the actual invalid address.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: b4e2f6ac12 ("i2c: apply DT flags when probing")
Cc: stable@kernel.org
Falling back unconditionally to HostNotify as primary client's interrupt
breaks some drivers which alter their functionality depending on whether
interrupt is present or not, so let's introduce a board flag telling I2C
core explicitly if we want wired interrupt or HostNotify-based one:
I2C_CLIENT_HOST_NOTIFY.
For DT-based systems we introduce "host-notify" property that we convert
to I2C_CLIENT_HOST_NOTIFY board flag.
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater).
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making mlxcpld_mux_reg_write() return a -ve error code for
all failure cases, just as was done in commit 7f638c1cb0 ("i2c: mux:
pca954x: fix i2c mux selection caching").
This also aligns the implementations of these two muxes in this area.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI always sets Tx/Rx FIFO to 32. This configuration will
cause problem if the IP core supports a FIFO size of less than 32.
The driver should read the FIFO size from the IP and select the smaller
one of the two.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In DTB case, i2c-core doesn't create slave device which is installed
on i2c-xgene bus because of missing code in this driver.
This patch fixes this issue.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater.)
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making pca954x_reg_write() return a negative error code for
all failure cases.
Fixes: 463e8f845c ("i2c: mux: pca954x: retry updating the mux selection on failure")
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.
Return -EIO in case of a failed data read. For all other
cases just return so subsequent operations will fail
and trigger the recovery.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
o STM can hook into the function tracer
o Function filtering now supports more advance glob matching
o Ftrace selftests updates and added tests
o Softirq tag in traces now show only softirqs
o ARM nop added to non traced locations at compile time
o New trace_marker_raw file that allows for binary input
o Optimizations to the ring buffer
o Removal of kmap in trace_marker
o Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
o Other various fixes and clean ups
Note, there are two patches marked for stable. These were discovered
near the end of the 4.9 rc release cycle. By the time I had them tested
it was just a matter of days before 4.9 would be released, and I
figured I would just submit them in the merge window. They are old
bugs and not critical. Nothing non-root could abuse.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJYUrFHFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
2+AIAIr20kSQV/nA5htGAeCTobVk3WUxY6bvjd9mIJDKPP19akNLyREW0G3KnfCr
yhx4aFRZG98fRu/6F8qieRosyN36lADDVYHelMFHMpcTOpE2aZGjaaOuNGxOEA9v
FmMPTX+K3+dzKyFP4l68R3+5JuQ1/AqLTioTWeLW8IDQ2OOVsjD8+0BuXrNKMJDY
o6U4Hk5U/vn+zHc6BmgBzloAXemBd7iJ1t5V3FRRGvm8yv3HU85Twc5ofGeYTWvB
J8PboEywRlIzxg0Kd8mxnMI5PgaKZSEc2ub8E7cY/CZ5PYpDE2xDA2hJmJgfYp00
1VW+DHRpRZfElsCcya6S6P4bs5Y=
=MGZ/
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This release has a few updates:
- STM can hook into the function tracer
- Function filtering now supports more advance glob matching
- Ftrace selftests updates and added tests
- Softirq tag in traces now show only softirqs
- ARM nop added to non traced locations at compile time
- New trace_marker_raw file that allows for binary input
- Optimizations to the ring buffer
- Removal of kmap in trace_marker
- Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
- Other various fixes and clean ups"
* tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (42 commits)
selftests: ftrace: Shift down default message verbosity
kprobes/trace: Fix kprobe selftest for newer gcc
tracing/kprobes: Add a helper method to return number of probe hits
tracing/rb: Init the CPU mask on allocation
tracing: Use SOFTIRQ_OFFSET for softirq dectection for more accurate results
tracing/fgraph: Have wakeup and irqsoff tracers ignore graph functions too
fgraph: Handle a case where a tracer ignores set_graph_notrace
tracing: Replace kmap with copy_from_user() in trace_marker writing
ftrace/x86_32: Set ftrace_stub to weak to prevent gcc from using short jumps to it
tracing: Allow benchmark to be enabled at early_initcall()
tracing: Have system enable return error if one of the events fail
tracing: Do not start benchmark on boot up
tracing: Have the reg function allow to fail
ring-buffer: Force rb_end_commit() and rb_set_commit_to_write() inline
ring-buffer: Froce rb_update_write_stamp() to be inlined
ring-buffer: Force inline of hotpath helper functions
tracing: Make __buffer_unlock_commit() always_inline
tracing: Make tracepoint_printk a static_key
ring-buffer: Always inline rb_event_data()
ring-buffer: Make rb_reserve_next_event() always inlined
...
Pull i2c updates from Wolfram Sang:
- the first series of making i2c_device_id optional instead of
mandatory (in favor of alternatives like of_device_id).
This involves adding a new probe callback (probe_new) which removes
some peculiarities I2C had for a long time now. The new probe is
matching the other subsystems now and the old one will be removed
once all users are converted. It is expected to take a while but
there is ongoing interest in that.
- SMBus Host Notify introduced 4.9 got refactored. They are now using
interrupts instead of the alert callback which solves multiple
issues.
- new drivers for iMX LowPower I2C, Mellanox CPLD and its I2C mux
- significant refactoring for bcm2835 driver
- the usual set of driver updates and improvements
* 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (46 commits)
i2c: fsl-lpi2c: read lpi2c fifo size in probe()
i2c: octeon: thunderx: Remove double-check after interrupt
i2c: octeon: thunderx: TWSI software reset in recovery
i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
i2c: sh_mobile: Add per-Generation fallback bindings
i2c: rcar: Add per-Generation fallback bindings
i2c: imx-lpi2c: add low power i2c bus driver
dt-bindings: i2c: imx-lpi2c: add devicetree bindings
i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
i2c: pxa: Add support for the I2C units found in Armada 3700
i2c: pxa: Add definition of fast and high speed modes via the regs layout
dt-bindings: i2c: pxa: Update the documentation for the Armada 3700
i2c: qup: support SMBus block read
i2c: qup: add ACPI support
i2c: designware: Consolidate default functionality bits
i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
i2c: mux: pca954x: Add ACPI support for pca954x
i2c: use an IRQ to report Host Notify events, not alert
i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
i2c: i801: use the BIT() macro for FEATURES_* also
...
The lpi2c fifo size is a read only parameter resides Parameter
Register. It's better to read lpi2c tx/rx fifo size in probe()
other than just define a macro for it.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 1bb1ff3e7c ("i2c: octeon: Improve performance if interrupt is
early") added a double-check around the wait_event_timeout() condition.
The performance problem that this commit tried to work-around
could not be reproduced. It also makes the wait condition more
complicated then it should be. Therefore remove the double-check.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I've seen i2c recovery reporting long loops of:
[ 1035.887818] i2c i2c-4: SCL is stuck low, exit recovery
[ 1037.999748] i2c i2c-4: SCL is stuck low, exit recovery
[ 1040.111694] i2c i2c-4: SCL is stuck low, exit recovery
...
Add a TWSI software reset which clears the status and
STA,STP,IFLG in SW_TWSI_EOP_TWSI_CTL.
With this the recovery works fine and above message is not seen.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch allows Cadence I2C controller to be selected in systems using Cadence Xtensa processors.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add per-Generation fallback bindings for R-Car SoCs.
This is in keeping with the compatibility string scheme is being adopted
for drivers for Renesas SoCs.
Also, improve readability by listing the rmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that it's not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also:
* Deprecate renesas,i2c-rcar. It seems poorly named as it is only
compatible with R-Car Gen 1. It also appears unused in mainline.
* Add some text to describe per-SoC bindings
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some tracepoints have a registration function that gets enabled when the
tracepoint is enabled. There may be cases that the registraction function
must fail (for example, can't allocate enough memory). In this case, the
tracepoint should also fail to register, otherwise the user would not know
why the tracepoint is not working.
Cc: David Howells <dhowells@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch adds lpi2c bus driver to support new i.MX products
which use lpi2c instead of the old imx i2c.
The lpi2c can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Both Merrifield TRM and Medfield TRM state:
"Both 7-bit and 10-bit addressing modes are supported."
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Armada 3700 has two I2C controllers that is compliant with the I2C
Bus Specificiation 2.1, supports multi-master and different bus speed:
Standard mode (up to 100 KHz), Fast mode (up to 400 KHz),
High speed mode (up to 3.4 Mhz).
This IP block has a lot of similarity with the PXA, except some register
offsets and bitfield. This commits adds a basic support for this I2C
unit.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
So far, the bit masks for the fast and high speed mode were statically
defined. Some IP blocks might use different bits for these modes.
This commit introduces new fields in order to enable the definition of
different bit masks for these features. If these fields are undefined,
ICR_FM and ICR_HS are selected to preserve backward compatibility with
other IPs.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C QUP driver relies on SMBus emulation support from the framework.
To handle SMBus block reads, the driver should check I2C_M_RECV_LEN
flag and should read the first byte received as the message length.
The driver configures the QUP hardware to read one byte. Once the
message length is known from this byte, the QUP hardware is configured
to read the rest.
Signed-off-by: Naveen Kaje <nkaje@codeaurora.org>
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support to get the device parameters from ACPI. Assume
that the clocks are managed by firmware.
Signed-off-by: Naveen Kaje <nkaje@codeaurora.org>
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a common place for default functionality bits for both platform
and pci driver.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the gpio controller supports it and the gpio lines are concentrated
to one gpio chip, the mux controller pins will get updated simultaneously.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enables ACPI support for mux-pca954x driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Peter Rosin <peda@axentia.se>
[wsa: removed a trailing whitespace]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 0317e6c0f1.
Srinivas reported recently touchscreen and touchpad stopped working in
Haswell based machine in Linux 4.9-rc series with timeout errors from
i2c_designware:
[ 16.508013] i2c_designware INT33C3:00: controller timed out
[ 16.508302] i2c_hid i2c-MSFT0001:02: failed to change power setting.
[ 17.532016] i2c_designware INT33C3:00: controller timed out
[ 18.556022] i2c_designware INT33C3:00: controller timed out
[ 18.556315] i2c_hid i2c-ATML1000:00: failed to retrieve report from device.
I managed to reproduce similar errors on another Haswell based machine
where touchscreen initialization fails maybe in every 1/5 - 1/2 boots.
Since root cause for these errors is not clear yet and debugging is
ongoing it's better to revert this commit as we are near to release.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current SMBus Host Notify implementation relies on .alert() to
relay its notifications. However, the use cases where SMBus Host
Notify is needed currently is to signal data ready on touchpads.
This is closer to an IRQ than a custom API through .alert().
Given that the 2 touchpad manufacturers (Synaptics and Elan) that
use SMBus Host Notify don't put any data in the SMBus payload, the
concept actually matches one to one.
Benefits are multiple:
- simpler code and API: the client will just have an IRQ, and
nothing needs to be added in the adapter beside internally
enabling it.
- no more specific workqueue, the threading is handled by IRQ core
directly (when required)
- no more races when removing the device (the drivers are already
required to disable irq on remove)
- simpler handling for drivers: use plain regular IRQs
- no more dependency on i2c-smbus for i2c-i801 (and any other adapter)
- the IRQ domain is created automatically when the adapter exports
the Host Notify capability
- the IRQ are assign only if ACPI, OF and the caller did not assign
one already
- the domain is automatically destroyed on remove
- fewer lines of code (minus 20, yeah!)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On the platform tested, reading SMBNTFDDAT always returns 0 (using 1 read
of a word or 2 of 2 bytes). Given that we are not sure why and that we
don't need to rely on the data parameter in the current users of Host
Notify, remove this part of the code.
If someone wants to re-enable it, just revert this commit and data should
be available.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i801 mixes hexadecimal and decimal values for defining bits. However,
we have a nice BIT() macro for this exact purpose.
No functional changes, cleanup only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No functional changes, just typos and remove unused #define.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Also do not override any other configuration in this register.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device driver for Mellanox I2C controller logic, implemented in Lattice
CPLD device.
Device supports:
- Master mode
- One physical bus
- Polling mode
The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When loading the TX fifo to receive bytes on the I2C bus, we incorrectly
count the number of bytes:
rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR);
while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) {
if (rx_limit - dev->rx_outstanding <= 0)
break;
rx_limit--;
dev->rx_outstanding++;
}
DW_IC_RXFLR indicates how many bytes are available to be read in the
FIFO, dev->rx_fifo_depth is the FIFO size, and dev->rx_outstanding is
the number of bytes that we've requested to be read so far, but which
have not been read.
Firstly, increasing dev->rx_outstanding and decreasing rx_limit and then
comparing them results in each byte consuming "two" bytes in this
tracking, so this is obviously wrong.
Secondly, the number of bytes that _could_ be received into the FIFO at
any time is the number of bytes we have so far requested but not yet
read from the FIFO - in other words dev->rx_outstanding.
So, in order to request enough bytes to fill the RX FIFO, we need to
request dev->rx_fifo_depth - dev->rx_outstanding bytes.
Modifying the code thusly results in us reaching the maximum number of
bytes outstanding each time we queue more "receive" operations, provided
the transfer allows that to happen.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rather than reporting success for a short transfer due to interrupt
latency, report an error both to the caller, as well as to the kernel
log.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Deselect functionality can be ignored for device-trees with
"i2c-mux-idle-disconnect" entries if no platform_data is available.
By enabling the deselect functionality outside the platform_data
block the logic works as it did in previous kernels.
Fixes: 7fcac98071 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Ziyang Wu <ziywu@cisco.com>
[touched up a few minor issues /peda]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ACPI companion of the adapter has to be set for I2C controller
code to read and attach the slave devices described in the ACPI table
with the I2CSerialBus resource descriptor. Used ACPI_COMPANION_SET
macro to set this.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow more flexibility to bus speed selection. Now if there are I2C
slave connections defined in ACPI the speed of slowest device on the bus
will define the bus speed. However if also "clock-frequency" device
property is defined we should use the slowest of these two.
This is targeted to maker boards where developer may want to connect
slower I2C slave devices to the bus than defined in existing ACPI I2C
slave connections.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designware Core Driver doesn't handle the case at the moment.
The below patch supports this feature.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check for i2c_adapter_quirks structures that are only stored in the
quirks field of an i2c_adapter structure. This field is declared
const, so i2c_adapter_quirks structures that have this property can be
declared as const also.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ray Jui <ray.jui@broadcom.com> # for bcm-iproc
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
since clk_prepare_enable() is used to get i2c->clk, we should
use clk_disable_unprepare() to release it for the error path.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_PXA_PCI
drivers/i2c/busses/Kconfig: def_bool I2C_PXA && X86_32 && PCI && OF
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_pci_driver() uses the same init level priority as
builtin_pci_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver allows I2C routing controlled through CPLD select registers on
a wide range of Mellanox systems (CPLD Lattice device).
MUX selection is provided by digital and analog HW. Analog part is not
under SW control.
Digital part is under CPLD control (channel selection/de-selection).
Connectivity schema.
.---. .-------------.
| l | | |-- i2cx1 -- i2cx8
| i |-- i2cn --+--| mlxcpld mux |
| n | | | |-- i2cy1 -- i2cy8
| u | | '-------------'
| x | | |
'---' '---------'
i2c-mux-mlxpcld does not necessarily require i2c-mlxcpld. It can be used
along with another bus driver, and still control i2c routing through CPLD
mux selection, in case the system is equipped with CPLD capable of mux
selection control.
The Kconfig currently controlling compilation of this code is:
drivers/i2c/muxes/Kconfig:config I2C_MUX_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This will aid the seamless removal of the current probe()'s, more
commonly unused than used second parameter. Most I2C drivers can
simply switch over to the new interface, others which have DT
support can use its own matching instead and others can call
i2c_match_id() themselves. This brings I2C's device probe method
into line with other similar interfaces in the kernel and prevents
the requirement to pass an i2c_device_id table.
Suggested-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: fix rebase conflicts and adapt for dev_pm_domain_{attach,detach}]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When there was no other way to match a I2C device to driver i2c_match_id()
was exclusively used. However, now there are other types of tables which
are commonly supplied, matching on an i2c_device_id table is used less
frequently. Instead of _always_ calling i2c_match_id() from within the
framework, we only need to do so from drivers which have no other way of
matching. This patch makes i2c_match_id() available to the aforementioned
device drivers.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the I2C framework insists on devices supplying an I2C ID
table. Many of the devices which do so unnecessarily adding quite a
few wasted lines to kernel code. This patch allows drivers a means
to 'not' supply the aforementioned table and match on DT match tables
instead.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This function provides a single call for all I2C devices which need to
match firstly using traditional OF means i.e by of_node, then if that
fails we attempt to match using the supplied I2C client name with a
list of supplied compatible strings with the '<vendor>,' string
removed. The latter is required due to the unruly naming conventions
used currently by I2C devices.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: Fix static inline usage on !CONFIG_OF]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A great deal of I2C devices are currently matched via DT node name, and
as such the compatible naming convention of '<vendor>,<device>' has gone
somewhat awry - some nodes don't supply one, some supply an arbitrary
string and others the correct device name with an arbitrary vendor prefix.
In an effort to correct this problem we have to supply a mechanism to
match a device by compatible string AND by simple device name. This
function strips off the '<vendor>,' part of a supplied compatible string
and attempts to match without it.
It is also used for sysfs, where a user can choose to instantiate a
device on an i2c bus using the sysfs interface by providing a string and
address to match and communicate with the device on the bus. Presently
this string is only matched against the old i2c device id style strings,
even in the presence of full device tree compatible strings with vendor
prefixes.
Providing a vendor-prefixed string to the sysfs interface will not match
against the device tree of_match_device() calls as there is no device
tree node to parse from the sysfs interface.
This function can match both vendor prefixed and stripped compatible
strings on the sysfs interface.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We get the following build error from UM Linux after adding
an entry to drivers/iio/gyro/Kconfig that issues "select I2C_MUX":
ERROR: "devm_ioremap_resource"
[drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
ERROR: "of_address_to_resource"
[drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
It appears that the I2C mux core code depends on HAS_IOMEM
for historical reasons, while CONFIG_I2C_MUX_REG does *not*
have a direct dependency on HAS_IOMEM.
This creates a situation where a allyesconfig or allmodconfig
for UM Linux will select I2C_MUX, and will implicitly enable
I2C_MUX_REG as well, and the compilation will fail for the
register driver.
Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and
removing the dependency from I2C_MUX.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Jonathan Cameron <jic23@jic23.retrosnub.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Here we're providing dereference protection for i2c_match_id(), which
saves us having to do it each time it's called. We're also stripping
out the (now) needless checks in i2c_device_match(). This patch paves
the way for other, similar code trimming.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some drivers like i2c-gpio do not have dedicated pinctrl states. They
broke when error checking for pinctrl was added. Detect them now, and in
their case, simply skip over pinctrl configuration.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support a dynamic clock by reading the frequency and setting the
divisor in the transfer function instead of during probe.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use i2c_adapter->timeout for the completion timeout value. The core
default is 1 second.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.
This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
of using polling. There is no interrupt for Transfer Active, but by
not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
CLEAR to the control register instead of just zero.
Using just zero gave many errors. This might be the reason why
downstream had to disable this feature and make it available with a
module parameter.
I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The controller can't support this flag, so remove it.
Documentation/i2c/i2c-protocol states that all of the message is sent:
I2C_M_IGNORE_NAK:
Normally message is interrupted immediately if there is [NA] from the
client. Setting this flag treats any [NA] as [A], and all of
message is sent.
>From the BCM2835 ARM Peripherals datasheet:
The ERR field is set when the slave fails to acknowledge either
its address or a data byte written to it.
So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.
(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.
Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.
Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.
The BCM2835 ARM Peripherals datasheet has this to say about the flags:
TXD: is set when the FIFO has space for at least one byte of data.
RXD: is set when the FIFO contains at least one byte of data.
TXW: is set during a write transfer and the FIFO is less than full.
RXR: is set during a read transfer and the FIFO is or more full.
Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
i2c_register_driver() i2c_del_adapter()
driver_register() ...
bus_add_driver() ...
... bus_for_each_drv(..., __process_removed_adapter)
... i2c_do_del_adapter()
... list_for_each_entry_safe(..., &driver->clients, ...)
INIT_LIST_HEAD(&driver->clients);
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Some SoC might load the GPIO driver after the I2C driver and
using the I2C bus recovery mechanism via GPIOs. In this case
it is crucial to defer probing if the GPIO request functions
do so, otherwise the I2C driver gets loaded without recovery
mechanisms enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I2C DesignWare may abort transfer with arbitration lost if I2C slave pulls
SDA down quickly after falling edge of SCL. Reason for this is unknown but
after trial and error it was found this can be avoided by enabling non-zero
SDA RX hold time for the receiver.
By the specification SDA RX hold time extends incoming SDA low to high
transition by n * ic_clk cycles but only when SCL is high. However it
seems to help avoid above faulty arbitration lost error.
Bits 23:16 in IC_SDA_HOLD register define the SDA RX hold time for the
receiver. Be conservative and enable 1 ic_clk cycle long hold time in
case boot firmware hasn't set it up.
Reported-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.
However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.
So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus block command uses the first byte of buffer for the data length.
The dma_buffer should be increased by 1 to avoid the overrun issue.
Reported-by: Phil Endecott <phil_gjouf_endecott@chezphil.org>
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.
We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd301. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.
If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Fixes: 4f001fd301 ("i2c: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+0Q/
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into i2c/for-next
[wsa: fell through the cracks, applied to 4.9 now]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: 'i2c-bus' node support for v4.8-rc1
This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs
Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
axxia_i2c_probe() does not disable clock in case of failure
in i2c_add_adapter(). Also it ignores returned value from
clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.
Return -ETIMEDOUT in case of a failed data read. For all other
cases just return so subsequent operations will fail.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.
Add wait code to relax the status register check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Kaby Lake PCH-H has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add Kaby Lake PCH-H PCI ID to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This routine is only used together with lockdep for nested locking.
The number of lock subclasses is limited to 8 as defined in lockdep.h
Emit a warning if the adapter depth exceeds the maximum number of
lockdep subclasses.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For crazy setups in which an i2c gpio expander is behind an i2c gpio
multiplexer controlled by a gpio provided a second expander using the
same device driver we need to explicitly tell lockdep how to handle
nested locking.
Export i2c_adapter_depth() as public API to be reused outside of i2c
core code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90
Modules linked in:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch fixs the following warning:
drivers/i2c/busses/i2c-rk3x.c: In function 'rk3x_i2c_v1_calc_timings':
drivers/i2c/busses/i2c-rk3x.c:745:41: warning: variable 'min_total_ns' set but not used [-Wunused-but-set-variable]
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the following sparse warning:
drivers/i2c/busses/i2c-rk3x.c:888:17: warning: cast truncates bits from constant value (ffffffffff00 becomes ffffff00)
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When enumerating I2C devices connected to an I2C adapter we scan the whole
namespace (as it is possible to have devices anywhere in that namespace,
not just below the I2C adapter device) and add each found device to the I2C
bus in question.
Now after commit 525e6fabea ("i2c / ACPI: add support for ACPI
reconfigure notifications") checking of the adapter handle to the one found
in the I2cSerialBus() resource was moved to happen after resources of the
I2C device has been parsed. This means that if the I2cSerialBus() resource
points to an adapter that does not exists in the system we still parse
those resources. This is problematic in particular because
acpi_dev_resource_interrupt() tries to configure GSI if the device also has
an Interrupt() resource. Failing to do that results errrors like this to be
printed on the console:
[ 10.409490] ERROR: Unable to locate IOAPIC for GSI 37
To fix this we pass the I2C adapter to i2c_acpi_get_info() and make sure
the handle matches the one in the I2cSerialBus() resource before doing
anything else to the device.
Reported-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The cached value of the last selected channel prevents retries on the
next call, even on failure to update the selected channel. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In case the high-level controller (HLC) is used the status code is
reported at a different location. Check that location after HLC
write operations if the ready bit is not set and return an appropriate
error code instead of always returning -EAGAIN.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to a bug in the ThunderX I2C hardware sending STOP during
a recovery attempt could lock up the hardware. To work around
this problem do not send STOP at the beginning of the recovery
but use the override registers to bring the TWSI including
the high-level controller out of the bad state.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The set SCL recovery function unconditionally pulls the SCL line low.
Only pull SCL line low according to val parameter.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Since commit 1c4b6c3bcf ("i2c: imx: implement bus recovery") the
driver starts to use gpio/pinctrl to support optional bus recovery
feature. But pinctrl is not always usable. There are platforms such
as ls1021a and ls1043a that don't support pinctrl, and it could just
be broken due to old/broken device tree. The patch makes it really
optional that the probe function won't bailout on pinctrl problems
instead it just disables bus recovery and prints out notification when
there is problem with pinctrl. Since pinctrl is only used by bus
recovery in this driver, move pinctrl initialization into bus recovery
init function to prevent confusion.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Depending on a number of factors including:
- Which exact Rockchip SoC we're working with
- How deep we suspend
- Which i2c port we're on
We might lose the state of the i2c registers at suspend time.
Specifically we've found that on rk3399 the i2c ports that are not in
the PMU power domain lose their state with the current suspend depth
configured by ARM Tursted Firmware.
Note that there are very few actual i2c registers that aren't configured
per transfer anyway so all we actually need to re-configure are the
clock config registers. We'll just add a call to rk3x_i2c_adapt_div()
at resume time and be done with it.
NOTE: On rk3399 on ports whose power was lost, I put printouts in at
resume time. I saw things like:
before: con=0x00010300, div=0x00060006
after: con=0x00010200, div=0x00180025
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Tested-by: David Wu <david.wu@rock-chips.com>
[wsa: removed duplicate const]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the adapter is set to the master mode at the first use.
Since then, it is kept in the slave mode, so unexpected glitch
signals on the I2C lines may cause the adapter into insane state.
Setting it to the master mode along with initialization solves the
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Akio Noda <noda.akio@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix the following warnings reported by coccinelle for the Tegra I2C
driver.
drivers/i2c/busses/i2c-tegra.c:513:2-23: WARNING: Assignment of bool to 0/1
drivers/i2c/busses/i2c-tegra.c:539:3-24: WARNING: Assignment of bool to 0/1
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To summarize the issue observed in error cases:
SW Flow: For i2c message transfer, packet header and data payload is
posted and then required error/packet completion interrupts are enabled
later.
HW flow: HW process the packet just after packet header is posted, if
ARB lost/NACK error occurs (SW will not handle immediately when error
happens as error interrupts are not enabled at this point). HW assumes
error is acknowledged and clears current data in FIFO, But SW here posts
the remaining data payload which still stays in FIFO as stale data
(data without packet header).
Now once the interrupts are enabled, SW handles ARB lost/NACK error by
clearing the ARB lost/NACK interrupt. Now HW assumes that SW attended
the error and will parse/process stale data (data without packet header)
present in FIFO which causes invalid NACK errors.
Fix: Enable the error interrupts before posting the packet into FIFO
which make sure HW to not clear the fifo. Also disable the packet mode
before acknowledging errors (ARB lost/NACK error) to not process any
stale data. As error interrupts are enabled before posting the packet
header use spinlock to avoid preempting.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use readl_poll_timeout_atomic() function as *wait_for_config_load()
function can be called from interrupt context.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Define separate function for configuration load register handling
to make it use by different functions later.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During i2c controller initialization, when fifo flush fails return error
instead of returning the error during exit.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After CONFIG_LOAD register is programmed instead of explicitly waiting
for timeout, use readl_poll_timeout() to check for register value to get
updated or wait till timeout.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"i2c-sh_mobile" is used on sh7343, sh7366, sh7722, sh7723, and sh7724
only. As all of the above select ARCH_SHMOBILE, restrict its driver
dependencies from SUPERH to ARCH_SHMOBILE.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several ways to set the SDA hold time for i2c controller,
including: Device Tree, built-in device properties and ACPI. However,
if the SDA hold time is not specified by above method, we should
read the value, where it is preset by firmware, and save it to
sda_hold_time. This is needed because when i2c controller enters
runtime suspend, the DW_IC_SDA_HOLD value will be reset to chipset
default value. And during runtime resume, i2c_dw_init will be called
to reconfigure i2c controller. If sda_hold_time is zero, the chipset
default hold time will be used, that will be too short for some
platforms. Therefore, to have a better tolerance, the DW_IC_SDA_HOLD
value should be kept by sda_hold_time.
Signed-off-by: Zhuo-hao Lee <zhuo-hao.lee@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can't use a static property for all the changesets, so we now create
dynamic ones for each changeset.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It's better to have strings in the code like they appeared in the output.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes it trivial to constify them, so do that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Tegra124/132 the pins for I2C6 are shared with the Display Port AUX
(DPAUX) channel and on Tegra210 the pins for I2C4 and I2C6 are shared
with DPAUX1 and DPAUX0, respectively. The multiplexing of the pins is
handled by a register in the DPAUX and so the Tegra DPAUX driver has
been updated to register a pinctrl device for managing these pins.
The pins for these particular I2C devices are bound to the I2C device
prior to probing. However, these I2C devices are in a different power
partition to the DPAUX devices that own the pins. Hence, it is desirable
to place the pins in the 'idle' state and allow the DPAUX power
partition to switch off, when these I2C devices is not in use.
Therefore, add calls to place the I2C pins in the 'default' and 'idle'
states when the I2C device is runtime resumed and suspended,
respectively.
Please note that the pinctrl functions that set the state of the pins
check to see if the devices has pins associated and will return zero
if they do not. Therefore, it is safe to call these pinctrl functions
even for I2C devices that do not have any pins associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the Tegra I2C driver to use runtime PM and move the code in the
tegra_i2c_clock_enable/disable() functions to the PM runtime resume and
suspend callbacks, respectively.
Note that given that CONFIG_PM is not mandatory for Tegra, if CONFIG_PM
is not enabled and so runtime PM is not enabled, ensure that the I2C
clocks are turned on during probe and kept on by calling the resume
callback directly.
In the function tegra_i2c_init(), the variable 'err' does not need to be
initialised to zero in tegra_i2c_init() because it is initialised when
pm_runtime_get_sync() is called. Furthermore, to ensure we only return 0
from tegra_i2c_init(), it is necessary to re-initialise 'err' to 0 after
a successful call to pm_runtime_get_sync() because it can return a
positive value on success. However, alternatively re-initialise 'err' by
using the return value of the function tegra_i2c_flush_fifos() because
it can only be 0 or -ETIMEDOUT.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C adapter is unlocked regardless of whether the tegra_i2c_init()
called during the resume is successful or not. However, if the
tegra_i2c_init() is not successful, then ->is_suspended is not set to
false. Simplify the resume code by only setting ->is_suspended to false
if tegra_i2c_init() is successful and return the error code from
tegra_i2c_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All Tegra I2C devices have the name "Tegra I2C adapter" which is not
very useful when viewing the I2C adapter names via the sysfs. Therefore,
use the device name, which is unique for each I2C device, instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra has only supported device-tree for platform/board configuration
for quite some time now and so simplify the Tegra I2C driver by dropping
code for non device-tree platforms/boards.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing new line characters for the various error messages.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checkpatch warns about missing blank lines after declarations in the
Tegra I2C driver and so fix these.
Note that the initialisation of 'val' to zero in tegra_dvc_init() is
unnecessary and so remove this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checkpatch warns about spacing around the '<<' operator in the Tegra I2C
driver and so fix these by converting the bit definitions that are using
this operator to use the BIT macro.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checkpatch warns about some lines over 80 characters in the Tegra I2C
driver and so fix these.
While we are at it, prefix the second instance of "STOP condition" in
the comment with a "the".
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Disabling the adapter after each transfer adds additional delays
for each I2C transfer. Even if we don't wait for it to be disabled
anymore, on next transfer we will need to if we have several transfers
in a row.
Now during the transfer init we check if IC_TAR can be changed
dynamically, the status register for no activity and TX buffer being
empty. In this case we don't need to disable it
When a transfer fails the adapter will still be disabled - this is a
conservative approach. When transfers succeed, the adapter is left
enabled and it's configured so to disable interrupts.
Alternating register reads on 2 slaves:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00
Before:
8.638705161 seconds time elapsed ( +- 5.90% )
After:
7.516821591 seconds time elapsed ( +- 0.11% )
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adapter can be synthesized with dynamic tar update enabled or disabled.
When enabled it is not necessary to disable the adapter to change the slave
address in some situations, which saves some time per transaction.
There is no direct register to know if this feature is enabled but we can do it
indirectly by writing to the 10BIT_ADDR field in IC_CON: this field is
read only when dynamic tar update is enabled.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These are used in 2 places and will be needed in more.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we aren't going to continue using the controller we can just disable
it instead of waiting for it to complete. The biggest improvement here
is when a I2C transaction is completed and it doesn't block until
the adapter is disabled. When a new transfer is needed we will disable
and wait for its completion.
This way the adapter will continue changing its state in parallel to the
execution of the thread that requested the I2C transaction saving most
of the time 25~250 usec per I2C transaction.
A simple program doing a register read (1 byte write, 1 byte read)
alternating on 2 different slaves repeated 25k times for each and
measurements taken 4 times we get:
perf stat -r4 chrt -f 10 ./i2c-test /dev/i2c-1 25000 0x40 0x6 0x1e 0x00
Before:
30.879317977 seconds time elapsed ( +- 14.83% )
After:
8.638705161 seconds time elapsed ( +- 5.90% )
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fast mode is the default speed of i2c-designware which can be overridden
by platform data or by "clock-frequency" device property. Even though
the ACPI 5.1 can pass device properties via _DSD method, shipping systems
define the connection speed between I2C host and each slave in their
I2cSerialBus resources. Which means speed is not defined per bus but per
slave.
As there is now support in i2c-core to find the bus speed from ACPI use
that to set up the bus speed prior registering the I2C adapter.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptor which define each controller-slave
connection define the maximum speed supported by that connection.
Thus finding the maximum safe speed for the bus is to walk through all
I2cSerialBus resources that are associated to I2C controller and use the
speed of slowest connection.
Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.
This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does communication.
Previous version commit 55d38d060e ("i2c: core: Add function for finding
the bus speed from ACPI") got reverted due merge conflicts from
commit 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure
notifications").
This version is a bit bigger than previous version but is still sharing
the lowest and complicated part of I2cSerialBus lookup routines with the
existing code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.
Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.
This is updated version from commit a7003b6580 ("i2c: core: Cleanup I2C
ACPI namespace") that got reverted due merge conflicts from
commit 525e6fabea ("i2c / ACPI: add support for ACPI reconfigure
notifications").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enabled high speed mode. High speed mode can be turn on by
setting the clk_freq to 3400000. High speed HCNT and LCNT are needed
as there is no default value provided.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DW_IC_CON_MASTER, DW_IC_CON_SLAVE_DISABLE and DW_IC_CON_RESTART_EN are
common config that need to be set for i2c designware master. So, configure
it first without having to repeat inside the if else.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enabled fast mode plus. The fast mode plus and fast speed
share the same HCNT and LCNT register. So, the fast mode plus will only
run when the HCNT and LCNT value is provided. Else, it will run at fast
speed as default.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C designware controller can run at fast mode plus and high speed. This
patch adds the capability to get the HCNT, LCNT configuration via
FPCN (fast plus) and HSCN (high speed) ACPI method.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2c designware controller operate speed is configured in the register
IC_CON. Previously the operate speed is determined by a local variable
clk_freq. This patch will move the local variable clk_freq into struct
dw_i2c_dev. This change will ease the set and get of the clk_freq.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sort include files alphabetically to reduce probability of merge
conflicts.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The register offsets are different between Octeon and ThunderX so move
them into the algorithm struct and get rid of the define.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SMBUS alert interrupt support. For now only device tree is
supported for specifying the alert. In case of ACPI an error
is returned.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ThunderX SOC uses the same i2c block as the Octeon SOC.
The main difference is that on ThunderX the device is a PCI device
so device probing is done via PCI, interrupts are MSI-X. The
clock rates can be set via device tree or ACPI.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move common functionality into a separate file in preparation of the
re-use from the ThunderX i2c driver.
Functions are slightly re-ordered but no other changes are included.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is an intermediate commit in preparation of the driver split.
The module rename in this commit will be reverted in the next patch,
this is just done to make the series bisectible.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Keep a direct pointer to the chip description instead of an index into
the chip description array.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
No longer rely on the implicit matching with the i2c device name, use
an explicit compatible string instead.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
The i2c mux core can then take appropriate action depending on if it is
used for an actual i2c mux, for a gate or for an arbitrator (the last
is the case for these drivers). This adds support for the new clearer
and more compact devicetree bindings that was added recently.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Backwards compatibility is preserved; the subnodes are in practice
optional.
However, the mux core needs to know what subnode it should examine, so add
a couple of new flags for i2c_mux_alloc for this purpose.
The rule is that if the mux core finds a 'reg' property in the appropriate
subnode, e.g. if 'reg' exists in the 'i2c-mux' subnode, then the mux core
will assume that this is an old style entry and not an i2c-mux subnode
(correspondingly for arbitrators and gates with 'i2c-arb' and 'i2c-gate').
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
We must use the same device we used for mapping.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We must use the same device we used for mapping.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure the index to the active channel is invalidated when switching
fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This unifies usage with i2c_lock_bus and i2c_unlock_bus, and paves the
way for the next patch which looks a bit saner with this preparatory
work taken care of beforehand.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
meson_i2c_xfer_msg()
reinit_completion()
...
/* Start the transfer */
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
brcmstb_send_i2c_cmd()
reinit_completion()
...
/* initiate transfer by setting iic_enable */
...
brcmstb_i2c_wait_for_completion()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
bcm_kona_send_i2c_cmd()
reinit_completion()
...
bcm_kona_i2c_send_cmd_to_ctrl()
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
bcm_iproc_i2c_xfer_single_msg()
reinit_completion()
...
(activate the transfer)
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The "alternative command" feature was introduced with sama5d2 SoCs.
Its purpose is to let the hardware i2c controller automatically send the
STOP condition on the i2c bus at the end of a data transfer.
Without this feature, the i2c driver has to write the 'STOP' bit into the
Control Register so the hardware i2c controller is triggered to send the
STOP condition on the bus.
Using the "alternative command" feature requires to set the transfer data
length into the 8bit DATAL field of the Alternative Command Register.
Hence only data transfers up to 255 bytes can take advantage of the
"alternative command" feature. For greater data transfer sizes, the driver
should use the previous implementation, when the "alternative command"
support was not implemented yet.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_disable_unprepare() is missed on failure paths in ocores_i2c_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cros_ec_cmd_xfer returns success status if the command transport
completes successfully, but the execution result is incorrectly ignored.
In many cases, the execution result is assumed to be successful, leading
to ignored errors and operating on uninitialized data.
We've recently introduced the cros_ec_cmd_xfer_status() helper to avoid these
problems. Let's use it.
[Regarding the 'Fixes' tag; there is significant refactoring since the driver's
introduction, but the underlying logical error exists throughout I believe]
Fixes: 9d230c9e4f ("i2c: ChromeOS EC tunnel driver")
Cc: <stable@vger.kernel.org> # 9798ac6d32 mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We also need to revert the dynamic OF change, so we get a consistent
state again. Otherwise, we might have two devices enabled e.g. after
pinctrl setup fails.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
Pull i2c updates from Wolfram Sang:
"Here is the I2C pull request for 4.8:
- the core and i801 driver gained support for SMBus Host Notify
- core support for more than one address in DT
- i2c_add_adapter() has now better error messages. We can remove all
error messages from drivers calling it as a next step.
- bigger updates to rk3x driver to support rk3399 SoC
- the at24 eeprom driver got refactored and can now read special
variants with unique serials or fixed MAC addresses.
The rest is regular driver updates and bugfixes"
* 'i2c/for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (66 commits)
i2c: i801: use IS_ENABLED() instead of checking for built-in or module
Documentation: i2c: slave: give proper example for pm usage
Documentation: i2c: slave: describe buffer problems a bit better
i2c: bcm2835: Don't complain on -EPROBE_DEFER from getting our clock
i2c: i2c-smbus: drop useless stubs
i2c: efm32: fix a failure path in efm32_i2c_probe()
Revert "i2c: core: Cleanup I2C ACPI namespace"
Revert "i2c: core: Add function for finding the bus speed from ACPI"
i2c: Update the description of I2C_SMBUS
i2c: i2c-smbus: fix i2c_handle_smbus_host_notify documentation
eeprom: at24: tweak the loop_until_timeout() macro
eeprom: at24: add support for at24mac series
eeprom: at24: support reading the serial number for 24csxx
eeprom: at24: platform_data: use BIT() macro
eeprom: at24: split at24_eeprom_write() into specialized functions
eeprom: at24: split at24_eeprom_read() into specialized functions
eeprom: at24: hide the read/write loop behind a macro
eeprom: at24: call read/write functions via function pointers
eeprom: at24: coding style fixes
eeprom: at24: move at24_read() below at24_eeprom_write()
...
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* acpi-tables:
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
spi / ACPI: add support for ACPI reconfigure notifications
i2c / ACPI: add support for ACPI reconfigure notifications
ACPI: add support for ACPI reconfiguration notifiers
ACPI / scan: fix enumeration (visited) flags for bus rescans
ACPI / documentation: add SSDT overlays documentation
ACPI: ARM64: support for ACPI_TABLE_UPGRADE
ACPI / tables: introduce ARCH_HAS_ACPI_TABLE_UPGRADE
ACPI / tables: move arch-specific symbol to asm/acpi.h
ACPI / tables: table upgrade: refactor function definitions
ACPI / tables: table upgrade: use cacheable map for tables
Conflicts:
arch/arm64/include/asm/acpi.h
Fixes dmesg spam when we just need to wait a moment for the clock
driver to probe.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is the only failure path in efm32_i2c_probe(),
where clk_disable_unprepare() is missed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 1b5b23718b ("i2c: efm32: new bus driver")
Cc: stable@kernel.org
This reverts commit a7003b65801e17a19617a509b2dbae3442ddd709.There were
too heavy merge conflicts and the driver code making use of this was not
ready yet anyhow. So, we wait one cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 55d38d060e. There were
too heavy merge conflicts and the driver code making use of this was not
ready yet anyhow. So, we wait one cycle.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We support the SMBus Host Notify protocol now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The parameter description is from a previous implementation, update
it to describe the actual implementation.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
1. The current QCOM I2C driver code is failing for transfer length
greater than 255. This is happening due to improper segments length
as the I2C DMA segments can be maximum of 256 bytes.
2. The transfer length tlen was being initialized with 0 for 256
bytes, which is being passed for DMA mappings resulting in improper
DMA mapping length.
This patch fixes the above said problems by initializing the block
count with the values calculated in qup_i2c_set_blk_data and calculating
the remaining length for last DMA segment. Also, the block data length
need to be decremented after each transfer. Additionally, this patch
corrects the tlen assignment for DMA mapping.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
1. Current QCOM I2C driver hangs when sending data to address 0x03-0x07
in some scenarios. The QUP controller generates invalid write in this
case, since these addresses are reserved for different bus formats.
2. Also, the error handling is done by I2C QUP ISR in the case of DMA
mode. The state need to be RESET in case of any error for clearing the
available data in FIFO, which otherwise leaves the BAM DMA controller
in hang state.
This patch fixes the above two issues by clearing the error bits from
I2C and QUP status in ISR in case of I2C error, QUP error and resets
the QUP state to clear the FIFO data.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver transfer to a message with NOACK always in any size.
If client (eg. EDID segment point message) needs NOACK condition, it can
use I2C_M_IGNORE_NAK flag.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BCM7xxx ARM and MIPS based SoCs share a similar I2C hardware block.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5 specification doesn't have property for the I2C bus speed but
I2cSerialBus resource descriptors which define each controller-slave
connection define the maximum speed supported by that connection.
Thus finding the maximum safe speed for the bus is to walk all
I2cSerialBus resources that are associated to I2C controller and use
the speed of slowest connection.
Add function i2c_acpi_find_bus_speed() to the i2c-core that adapter
drivers can call prior registering itself to core.
This implies two-step walk through the I2cSerialBus resources: call to
i2c_acpi_find_bus_speed() does the first scan and finds the safe bus
speed that adapter drivers can set up. Adapter driver registration does
the second scan when i2c-core creates the I2C slaves by calling the
i2c_acpi_register_devices(). In that way the bus speed is set in case
slave device probe gets called during registration and does
communication.
Implement this by reusing the existing ACPI I2C walk routines in the
i2c-core. Extend them so that slowest connection speed is saved during
the walk and I2C slaves are registered only when calling through the
i2c_acpi_register_devices() with the i2c_adapter pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C ACPI enumeration was originally implemented in another module under
drivers/acpi/ but was later moved into i2c-core with added support for
I2C ACPI operation region.
Rename these acpi_i2c_ prefixed functions, structures and defines in
i2c-core to i2c_acpi_ in order to have more consistent name space.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we revisited all error messages, we can use pr_fmt for the
remaining pr_* messages to ensure consistent output.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a warning loglevel instead of info and switch to dev_* for device
info. Also print which client was accessed.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use dev_err instead of pr_err for more details.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to WARN if no adapter name is given, otherwise we won't know who
missed to do that. Add error message if device registration fails.
Update error message for missing algo to match style of the others.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move recovery init to a seperate function to let have
i2c_register_adapter() less lines and to avoid goto and a label.
Refactor string handling there for consistency and to save some bytes.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On error, we should give idr back to the pool in any case.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* APIs to simplify the code a bit.
This patch also fixes the memory leak when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds supports for I2C device enumeration and removal via
ACPI reconfiguration notifications that are send as a result of an
ACPI table load or unload operation.
The code is very similar with the device tree reconfiguration code
with only small differences in the way we test and set the enumerated
state of the device:
* the equivalent of device tree's OF_POPULATED flag is the
flags.visited field in the ACPI device and the following
wrappers are used to manipulate it: acpi_device_enumerated(),
acpi_device_set_enumerated() and acpi_device_clear_enumerated()
* the device tree code checks of status of the OF_POPULATED flag to
avoid trying to create duplicate Linux devices in two places: once
when the controller is probed, and once when the reconfigure event
is received; in the ACPI code the check is performed only once when
the ACPI namespace is searched because this code path is invoked in
both of the two mentioned cases
The rest of the enumeration handling is similar with device tree: when
the Linux device is unregistered the ACPI device is marked as not
enumerated; also, when a device remove notification is received we
check that the device is in the enumerated state before continuing
with the removal of the Linux device.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added ACPI support for the I2C controller present on Broadcom's
Vulcan ARM64 processor. ACPI ID used by the controller is BRCM9007.
Changed the xlp9xx_i2c_get_frequency() function to use
device_property_read_u32() API so that the "clock-frequency" value
can be read from _DSD in ACPI mode.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver should be buildable with COMPILE_TEST so
add this to the dependency for it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no code protecting i2c_dev to be freed after it is returned
from i2c_dev_get_by_minor() and using it to access the value which we
already have (minor) isn't safe really.
Avoid using it and get the adapter directly from 'minor'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are more than 7 busses, but only 7 are user visible. Update comment
accordingly.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i801 chip can handle the Host Notify feature since ICH 3 as mentioned
in http://www.intel.com/content/dam/doc/datasheet/82801ca-io-controller-hub-3-datasheet.pdf
Enable the functionality unconditionally and propagate the alert
on each notification.
With a T440s and a Synaptics touchpad that implements Host Notify, the
payload data is always 0x0000, so I am not sure if the device actually
sends the payload or if there is a problem regarding the implementation.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
of_address_to_resource return 0 on successful call but
devm_ioremap_resource is called only if it returns non-zero value
Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Commit 497fbe2498 ("i2c: tegra: enable multi master mode for tegra210")
enables the Tegra I2C 'div_clk' for adapters using the multi-master mode
during the device probe. Although the probe error path was updated to
disable the clock on probe failure, there is one place after calling
tegra_i2c_init() where the clock will not be disabled on failure. Correct
the error path so that the 'div_clk' is disabled if calling
tegra_i2c_init() fails.
Fixes: 497fbe2498 ("i2c: tegra: enable multi master mode for tegra210")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On a CRC error while using hardware-supported PEC, an additional
error bit is set in the auxiliary status register. If this bit
isn't cleared, all subsequent operations will fail, essentially
hanging the controller.
The fix is simple: check, report, and clear the bit in
i801_check_post(). Also, in case the driver starts with the
hardware in that state, clear it in i801_check_pre() as well.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the 'i2c-bus' device-tree node is present for an I2C adapter then
parse this subnode for I2C slaves.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
An opal_msg of type OPAL_MSG_ASYNC_COMP contains the return code in the
params[1] struct member. However this isn't intuitive or obvious when
reading the code and requires that a user look at the skiboot
documentation or opal-api.h to verify this.
Add an inline function to get the return code from an opal_msg and update
call sites accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
[wsa: remove two empty lines while here]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Simply sort header block alphabetically.
While here fix an indentation in one place and update a copyright line for
Intel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enables I2C controllers found on Intel Edison board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On some platforms, such as Intel Medfield, the I2C slave devices are enumerated
through SFI tables where bus numbering is expected to be defined in the OS.
Make the bus number allocation robust for such platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I believe i2c-designware-baytrail.c doesn't have strict dependency that
Intel SoC IOSF Sideband support must be always built-in in order to be
able to compile support for Intel Baytrail I2C bus sharing HW semaphore.
Redefine build dependencies so that CONFIG_IOSF_MBI=y is required only
when CONFIG_I2C_DESIGNWARE_PLATFORM is built-in.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: David Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows applications to set the transfer timeout in 10ms increments via
ioctl I2C_TIMEOUT.
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As of next-20160607 with allyesconfig we get this linker failure:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x21bc0d): Section mismatch in reference from
the function intel_scu_devices_create() to the function
.init.text:i2c_register_board_info()
This is caused by the fact that intel_scu_devices_create() calls
i2c_register_board_info() and intel_scu_devices_create() is not
annotated with __init. This typically involves manual code
inspection and if one is certain this is correct we would
just peg intel_scu_devices_create() with a __ref annotation.
In this case this would be wrong though as the
intel_scu_devices_create() call is exported, and used in
the ipc_probe() on drivers/platform/x86/intel_scu_ipc.c.
The issue is that even though builtin_pci_driver(ipc_driver)
is used this just exposes the probe routine, which can occur
at any point in time if this bus supports hotplug. A race
can happen between kernel_init_freeable() that calls the init
calls (in this case registeres the intel_scu_ipc.c driver, and
later free_initmem(), which would free the i2c_register_board_info().
If a probe happens later in boot i2c_register_board_info() would
not be present and we should get a page fault.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
[wsa: made function declaration a one-liner]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
index gets incremented during check to determine if the
messages can be transferred with dma. But not reset after
that, resulting in wrong start value in subsequent loop,
causing failure. Fix it.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
qup_i2c_issue_read() derives the address from i2c_msg.
This called in the read path when I2C_M_RD flag is set.
Therefore, use the 8 bit address helper function.
Signed-off-by: Naveen Kaje <nkaje@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Among the bus errors reported from the QUP_MASTER_STATUS register
only NACK is considered and transfer gets suspended, while
other errors are ignored. Correct this and suspend the transfer
for other errors as well. This avoids unnecessary 'timeouts' which
happens when waiting for events that would never happen when there
is already an error condition on the bus. Also the error handling
procedure should be the same for both NACK and other bus errors in
case of dma mode. So correct that as well.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With CONFIG_DEBUG_SG is enabled and when dma mode is used, below dump is seen,
------------[ cut here ]------------
kernel BUG at include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.0-00459-g9f087b9-dirty #7
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
task: ffffffc036868000 ti: ffffffc036870000 task.ti: ffffffc036870000
PC is at qup_sg_set_buf.isra.13+0x138/0x154
LR is at qup_sg_set_buf.isra.13+0x50/0x154
pc : [<ffffffc0005a0ed8>] lr : [<ffffffc0005a0df0>] pstate: 60000145
sp : ffffffc0368735c0
x29: ffffffc0368735c0 x28: ffffffc036873752
x27: ffffffc035233018 x26: ffffffc000c4e000
x25: 0000000000000000 x24: 0000000000000004
x23: 0000000000000000 x22: ffffffc035233668
x21: ffffff80004e3000 x20: ffffffc0352e0018
x19: 0000004000000000 x18: 0000000000000028
x17: 0000000000000004 x16: ffffffc0017a39c8
x15: 0000000000001cdf x14: ffffffc0019929d8
x13: ffffffc0352e0018 x12: 0000000000000000
x11: 0000000000000001 x10: 0000000000000001
x9 : ffffffc0012b2d70 x8 : ffffff80004e3000
x7 : 0000000000000018 x6 : 0000000030000000
x5 : ffffffc00199f018 x4 : ffffffc035233018
x3 : 0000000000000004 x2 : 00000000c0000000
x1 : 0000000000000003 x0 : 0000000000000000
Process swapper/0 (pid: 1, stack limit = 0xffffffc036870020)
Stack: (0xffffffc0368735c0 to 0xffffffc036874000)
sg_set_bug expects that the buf parameter passed in should be from
lowmem and a valid pageframe. This is not true for pages from
dma_alloc_coherent which can be carveouts, hence the check fails.
Change allocation of sg buffers from dma_coherent memory to kzalloc
to fix the issue. Note that now dma_map/unmap is used to make the
kzalloc'ed buffers coherent before passing it to the dmaengine.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement fast mode plus that allows bus speeds of up to 1MHz.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- new method to caculate i2c timings for rk3399:
There was an timing issue about "repeated start" time at the I2C
controller of version0, controller appears to drop SDA at .875x (7/8)
programmed clk high. On version 1 of the controller, the rule(.875x)
isn't enough to meet tSU;STA
requirements on 100k's Standard-mode. To resolve this issue,
sda_update_config, start_setup_config and stop_setup_config for I2C
timing information are added, new rules are designed to calculate
the timing information at new v1.
- pclk and function clk are separated at rk3399
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[wsa: fixed whitespace issue]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c timing specs are really just constant data. There's no reason
to write code to init them, so move them out to structures. This not
only is a cleaner solution but it will reduce code duplication when we
introduce a new variant of rk3x_i2c_calc_divs() in a future patch.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Specifying the i2c SoC data in an array provides very little benefit and
gets unwieldly / confusing as the array grows since the next bit of code
needs to refer to elements in the array by their raw integral index.
Let's just create a single 'static const' structure for each SoC so that
we can refer to these structures by ID.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
rk3x_i2c_setup() gets called directly before rk3x_i2c_start(),
and the last thing in setup was to clean the IPD, so no reason
to do it at the beginning of start.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The "div_high" and "div_low" values are always used together.
Group them into a structure to make it easier to pass them
both around. This structure also provides a place for future
calculated timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add kernel-doc documentation for the elements of the previously
undocumented struct rk3x_i2c.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus Host Notify allows a slave device to act as a master on a bus to
notify the host of an interrupt. On Intel chipsets, the functionality
is directly implemented in the firmware. We just need to export a
function to call .alert() on the proper device driver.
i2c_handle_smbus_host_notify() behaves like i2c_handle_smbus_alert().
When called, it schedules a task that will be able to sleep to go through
the list of devices attached to the adapter.
The current implementation allows one Host Notification to be scheduled
while an other is running.
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
.alert() is meant to be generic, but there is currently no way
for the device driver to know which protocol generated the alert.
Add a parameter in .alert() to help the device driver to understand
what is given in data.
This patch is required to have the support of SMBus Host Notify protocol
through .alert().
Tested-by: Andrew Duggan <aduggan@synaptics.com>
For hwmon:
Acked-by: Guenter Roeck <linux@roeck-us.net>
For IPMI:
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
osif_table is never modified, so declare it as const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
David reported that the length for memset was incorrect (element sizes
were not taken into account). Then I saw that we are clearing kzalloced
memory, so we can simply drop this code.
Reported-by: David Binderman <dcb314@hotmail.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The interrupt handling code makes it look like several status values
may be merged together before being processed, while this will never
happen. Change from bit-wise OR to simple assignment to make it more
obvious and avoid misunderstanding.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some I2C devices have multiple addresses assigned, for example each address
corresponding to a different internal register map page of the device.
So far drivers which need support for this have handled this with a driver
specific and non-generic implementation, e.g. passing the additional address
via platform data.
This patch provides a new helper function called i2c_new_secondary_device()
which is intended to provide a generic way to get the secondary address
as well as instantiate a struct i2c_client for the secondary address.
The function expects a pointer to the primary i2c_client, a name
for the secondary address and an optional default address. The name is used
as a handle to specify which secondary address to get.
The default address is used as a fallback in case no secondary address
was explicitly specified. In case no secondary address and no default
address were specified the function returns NULL.
For now the function only supports look-up of the secondary address
from devicetree, but it can be extended in the future
to for example support board files and/or ACPI.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
of_match_table was not filled which prevents device to be
instantiated from device tree node.
Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the warning about a too long SMBUS message because
the ipmi_ssif driver triggers this warning too frequently so it
spams the message log.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During receive the controller requires the AAK flag for all
bytes but the final one. This was wrong in case of I2C_M_RECV_LEN,
where the decision if the final byte is to be transmitted
happened before adding the additional received length byte.
Set the AAK flag if additional bytes are to be received.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Many Intel systems the BIOS declares a SystemIO OpRegion below the SMBus
PCI device as can be seen in ACPI DSDT table from Lenovo Yoga 900:
Device (SBUS)
{
OperationRegion (SMBI, SystemIO, (SBAR << 0x05), 0x10)
Field (SMBI, ByteAcc, NoLock, Preserve)
{
HSTS, 8,
Offset (0x02),
HCON, 8,
HCOM, 8,
TXSA, 8,
DAT0, 8,
DAT1, 8,
HBDR, 8,
PECR, 8,
RXSA, 8,
SDAT, 16
}
There are also bunch of AML methods that that the BIOS can use to access
these fields. Most of the systems in question AML methods accessing the
SMBI OpRegion are never used.
Now, because of this SMBI OpRegion many systems fail to load the SMBus
driver with an error looking like one below:
ACPI Warning: SystemIO range 0x0000000000003040-0x000000000000305F
conflicts with OpRegion 0x0000000000003040-0x000000000000304F
(\_SB.PCI0.SBUS.SMBI) (20160108/utaddress-255)
ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver
The reason is that this SMBI OpRegion conflicts with the PCI BAR used by
the SMBus driver.
It turns out that we can install a custom SystemIO address space handler
for the SMBus device to intercept all accesses through that OpRegion. This
allows us to share the PCI BAR with the AML code if it for some reason is
using it. We do not expect that this OpRegion handler will ever be called
but if it is we print a warning and prevent all access from the SMBus
driver itself.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110041
Reported-by: Andy Lutomirski <luto@kernel.org>
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
The call to put_i2c_dev() frees "i2c_dev" so there is a use after
free when we call cdev_del(&i2c_dev->cdev).
Fixes: d6760b14d4 ('i2c: dev: switch from register_chrdev to cdev API')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I stumbled multiple times over 'return_i2c_dev', especially before the
actual 'return res'. It makes the code hard to read, so reanme the
function to 'put_i2c_dev' which also better matches 'get_free_i2c_dev'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c-dev had never moved away from the older register_chrdev interface to
implement its char device registration. The register_chrdev API has the
limitation of enabling only up to 256 i2c-dev busses to exist.
Large platforms with lots of i2c devices (i.e. pluggable transceivers)
with dedicated busses may have to exceed that limit.
In particular, there are also platforms making use of the i2c bus
multiplexing API, which instantiates a virtual bus for each possible
multiplexed selection.
This patch removes the register_chrdev usage and replaces it with the
less old cdev API, which takes away the 256 i2c-dev bus limitation.
It should not have any other impact for i2c bus drivers or user space.
This patch has been tested on qemu x86 and qemu powerpc platforms with
the aid of a module which adds and removes 5000 virtual i2c busses, as
well as validated on an existing powerpc hardware platform which makes
use of the i2c bus multiplexing API.
i2c-dev busses with device minor numbers larger than 256 have also been
validated to work with the existing i2c-tools.
Signed-off-by: Erico Nunes <erico.nunes@datacom.ind.br>
[wsa: kept includes sorted]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ARCH name was changed during the review process of the mach, and
this driver was forgotten to be converted. Fix it now.
http://article.gmane.org/gmane.linux.ports.arm.kernel/456331
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[wsa: updated commit message slightly]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When the DMA configuration fails, there is a log reporting that we can't
use DMA and indicating the error number. When booting the kernel, it is
annoying to see this error number. Moreover, people can think something
is going wrong. It is not the case, it means that DMA can't be used but
it doesn't prevent to use i2c.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If NO_DMA=y:
drivers/built-in.o: In function `rcar_i2c_dma_unmap':
i2c-rcar.c:(.text+0x6f06c6): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `rcar_i2c_dma':
i2c-rcar.c:(.text+0x6f07e2): undefined reference to `bad_dma_ops'
i2c-rcar.c:(.text+0x6f0838): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
New drivers should not use dma_request_slave_channel_reason() but
dma_request_chan(). The former is a macro to the later so this change do
not effect the driver in any way.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address and some data is still handled using
the old state machine, it is sending the bulk of the data that is done
via DMA.
The first byte of a transmission and the last two bytes of reception are
sent/received using PIO. This is needed for the HW to have access to the
first byte before DMA transmit and to be able to set the STOP condition
for DMA reception.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed a checkpatch warning]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
>From I2C specifications:
http://www.nxp.com/documents/user_manual/UM10204.pdf
Chapter 3.1.16, when the i2c device held the SDA line low, the master
should send 9 clocks pulses to try to recover.
Signed-off-by: Frederic Pillon <frederic.pillon@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A custom recovery function doesn't need these pointers to be populated
because it may work differently internally.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
i2c_bit_quirk_no_clk_stretch is used in i2c-algo-bit.c only, so
declare it as static.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Disable clock before returning error in tegra_i2c_init() as its leaves
i2c clock ON in case of error and never turns off again as it will have
unbalanced clock enable/disable
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With a i2c topology like the following
GPIO ---| ------ BAT1
| v /
I2C -----+----------+---- MUX
| \
EEPROM ------ BAT2
there is a locking problem with the GPIO controller since it is a client
on the same i2c bus that it muxes. Transfers to the mux clients (e.g. BAT1)
will lock the whole i2c bus prior to attempting to switch the mux to the
correct i2c segment. In the above case, the GPIO device is an I/O expander
with an i2c interface, and since the GPIO subsystem knows nothing (and
rightfully so) about the lockless needs of the i2c mux code, this results
in a deadlock when the GPIO driver issues i2c transfers to modify the
mux.
So, observing that while it is needed to have the i2c bus locked during the
actual MUX update in order to avoid random garbage on the slave side, it
is not strictly a must to have it locked over the whole sequence of a full
select-transfer-deselect mux client operation. The mux itself needs to be
locked, so transfers to clients behind the mux are serialized, and the mux
needs to be stable during all i2c traffic (otherwise individual mux slave
segments might see garbage, or worse).
Introduce this new locking concept as "mux-locked" muxes, and call the
pre-existing mux locking scheme "parent-locked".
Modify the i2c mux locking so that muxes that are "mux-locked" locks only
the muxes on the parent adapter instead of the whole i2c bus when there is
a transfer to the slave side of the mux. This lock serializes transfers to
the slave side of the muxes on the parent adapter.
Add code to i2c-mux-gpio and i2c-mux-pinctrl that checks if all involved
gpio/pinctrl devices have a parent that is an i2c adapter in the same
adapter tree that is muxed, and request a "mux-locked mux" if that is the
case.
Modify the select-transfer-deselect code for "mux-locked" muxes so
that each of the select-transfer-deselect ops locks the mux parent
adapter individually.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of checking for i2c parent adapters for every lock/unlock, simply
override the locking for muxes to always lock/unlock the parent adapter
directly.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c_lock_bus() and i2c_unlock_bus(), which call the new lock_bus and
unlock_bus ops in the adapter. These funcs/ops take an additional flags
argument that indicates for what purpose the adapter is locked.
There are two flags, I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT, but they
are both implemented the same. For now. Locking the root adapter means
that the whole bus is locked, locking the segment means that only the
current bus segment is locked (i.e. i2c traffic on the parent side of
a mux is still allowed even if the child side of the mux is locked).
Also support a trylock_bus op (but no function to call it, as it is not
expected to be needed outside of the i2c core).
Implement i2c_lock_adapter/i2c_unlock_adapter in terms of the new locking
scheme (i.e. lock with the I2C_LOCK_ROOT_ADAPTER flag).
Locking the root adapter and locking the segment is the same thing for
all root adapters (e.g. in the normal case of a simple topology with no
i2c muxes). The two locking variants are also the same for traditional
muxes (aka parent-locked muxes). These muxes traverse the tree, locking
each level as they go until they reach the root. This patch is preparatory
for a later patch in the series introducing mux-locked muxes, which behave
differently depending on the requested locking. Since all current users
are using i2c_lock_adapter, which is a wrapper for I2C_LOCK_ROOT_ADAPTER,
we only need to annotate the calls that will not need to lock the root
adapter for mux-locked muxes. I.e. the instances that needs to use
I2C_LOCK_SEGMENT instead of i2c_lock_adapter/I2C_LOCK_ROOT_ADAPTER. Those
instances are in the i2c_transfer and i2c_smbus_xfer functions, so that
mux-locked muxes can single out normal i2c accesses to its slave side
and adjust the locking for those accesses.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When clock support was added to the i2c-mv64xxx, not all clk functions
had stubs when for !CONFIG_HAVE_CLK configurations. However, nowadays,
both "struct clk" and all the clock framework functions have stubs
when CONFIG_HAVE_CLK is not enabled, so it no longer makes sense to
carry such compile-time conditionals in the driver.
This commit was compile tested on both ARM64 (which has both
CONFIG_OF=y and CONFIG_HAVE_CLK=y) and PowerPC c2k_defconfig (which
has CONFIG_OF=y, CONFIG_HAVE_CLK disabled, and the i2c-mv64xxx driver
enabled).
The only non-trivial change is in the mv64xxx_of_config() function,
which was returning -ENODEV unconditionally if CONFIG_HAVE_CLK was
disabled. Simply removing this condition works fine because the first
test done by the function is to verify if drv_data->clk points to a
valid clock, and if it doesn't, we return -ENODEV. When
CONFIG_HAVE_CLK is disabled, devm_clk_get() unconditionally returns
NULL, so mv64xxx_of_config() will return -ENODEV when no clock is
provided, which is the intended behavior.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of separately calling clk_prepare()/clk_enable(), use
clk_prepare_enable(), and instead of calling
clk_disable()/clk_unprepare(), use clk_disable_unprepare(). Those
handy shortcuts have been introduced specifically to simplify the
numerous call sites were both functions were called in sequence.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a clock is registered by a platform driver and not by the
OF_CLK_DECLARE() mechanism, it might show up after the first attempt
to probe i2c-mv64xxx. In order to solve this, we need to handle
-EPROBE_PREFER as a special return value of devm_clk_get(), and return
the same error code from probe().
This gives us three situations:
- There is no reference to a clock in the DT. In this case,
devm_clk_get() returns an error that is not -EPROBE_DEFER
(something like -ENODEV), and we continue the probing without
enabling the clock.
- There is a reference to the clock in the DT, and the clock is
ready. devm_clk_get() returns a valid reference to the clock, and
we prepare/enable it.
- There is a reference to the clock in the DT, but the clock is not
ready. devm_clk_get() returns -EPROBE_DEFER, and we exit from
probe() with the same error code so that probe() is tried again
later.
This is needed for Marvell Armada 7K/8K, where the clock driver is a
platform driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The new ARM64 Marvell Armada 7K/8K SoC family is using the same I2C
controller as the 32-bits Marvell EBU SoCs, so this commit allows
mv64xxx to be enabled when ARCH_MVEBU=y.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CN3860 does not interrupt the CPU when the i2c status changes. If
we get a timeout, and see the status has in fact changed, we know we
have this problem, and drop back to polling.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a race between the TWSI interrupt and the condition
that is required before proceeding:
Low-level: interrupt flag bit must be set
High-level controller: valid bit must be clear
If the interrupt comes too early and the condition is not met
the wait will time out, and the transfer is aborted leading
to very poor performance.
To avoid this race retry for the condition ~80 µs later.
The retry is avoided on the very first invocation of
wait_event_timeout() (which tests the condition before entering
the wait and is therefore always wrong in this case).
EEPROM reads on 100kHz i2c now measure ~5.2kB/s, about 1/2 what's
achievable, and much better than the worst-case 100 bytes/sec before.
While at it remove the debug print from the low-level wait function.
Signed-off-by: Peter Swain <pswain@cavium.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Zero-length message support (SMBUS QUICK or i2c) never worked with
the Octeon hardware. Disable SMBUS QUICK support and bail out in
case of a zero-length i2c request.
After this change 'i2c-detect -q' will return an error on Octeon but
the previously reported results were wrong anyway.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The clk_prepare_enable() function can fail so check the return
value and propagate the error in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver not always prints the error code in case of a failure but this
information can be very useful for debugging. So let's print if available.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improve the readability by:
- fixing indentation,
- switching to proper block comments,
- removing spurious blank lines,
- checkpatch: void function return statements are not generally useful,
- checkpatch: braces {} are not necessary for any arm of this
statement,
- checkpatch: missing a blank line after declarations.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cleanup the weird function-level comments and remove obvious
documentation for probe/remove.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If during probe() the s3c24xx_i2c_init() failed, the clock was left in
disabled but prepared state.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cn78xx has a different interrupt architecture, so we have to manage
the interrupts differently.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use High-Level Controller (HLC) when possible. The HLC can read/write
up to 8 bytes and is completely optional. The most important difference
of the HLC is that it only requires one interrupt for a transfer
(up to 8 bytes) where the low-level read/write requires 2 interrupts
plus one interrupt per transferred byte. Since the interrupts are costly
using the HLC improves the performance. Also, the HLC provides improved
error handling.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[wsa: fixed trivial checkpatch warnings]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add helper function that reads back a value after writing to
make sure the write is finished and use it in octeon_i2c_write_int().
Signed-off-by: Peter Swain <pswain@cavium.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the i2c bus recovery framework using generic SCL recovery.
If this fails try to reset the hardware. The recovery is triggered
during START on timeout of the interrupt or failure to reach
the START / repeated-START condition.
The START function is moved to xfer and while at it remove the
xfer debug message (i2c core already provides a debug message
for this).
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[wsa: removed one empty line]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Introduce a function that checks for valid status codes depending
on the phase of a transmit or receive. Also add all existing status
codes and improve error handling for various states.
The Octeon TWSI has an "assert acknowledge" bit (TWSI_CTL_AAK) that
is required to be set in master receive mode until the last byte is
requested. The state check needs to consider if this bit was set.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The lock is taken while reading two registers. On RT the first lock is
taken in hard irq where it might sleep and in the threaded irq.
The threaded irq runs in oneshot mode so the hard irq does not run until
the thread the completes so there is no reason to grab the lock.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grygorii.strashko@ti.com: drop locking from isr completely and remove
lock field from struct omap_i2c_dev]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Share the ACPI companion for the platform device with the
i2c adapter, so that the adapter has access to the properties
defined in ACPI tables.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The exynos5 I2C controller driver always prepares and enables a clock
before using it and then disables unprepares it when the clock is not
used anymore.
But this can cause a possible ABBA deadlock in some scenarios since a
driver that uses regmap to access its I2C registers, will first grab
the regmap lock and then the I2C xfer function will grab the prepare
lock when preparing the I2C clock. But since the clock driver also
uses regmap for I2C accesses, preparing a clock will first grab the
prepare lock and then the regmap lock when using the regmap API.
An example of this happens on the Exynos5422 Odroid XU4 board where a
s2mps11 PMIC is used and both the s2mps11 regulators and clk drivers
share the same I2C regmap.
The possible deadlock is reported by the kernel lockdep:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(sec_core:428:(regmap)->lock);
lock(prepare_lock);
lock(sec_core:428:(regmap)->lock);
lock(prepare_lock);
*** DEADLOCK ***
Fix it by leaving the code prepared on probe and use {en,dis}able in
the I2C transfer function.
This patch is similar to commit 34e81ad5f0 ("i2c: s3c2410: fix ABBA
deadlock by keeping clock prepared") that fixes the same bug in other
driver for an I2C controller found in Samsung SoCs.
Reported-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Since commit ea8daa7b97 ("kbuild: Add option to turn incompatible
pointer check into error"), assignments from an incompatible pointer
types have become a hard error, eg:
drivers/i2c/busses/i2c-cpm.c:545:91: error: passing argument 3 of
'dma_alloc_coherent' from incompatible pointer type
Fix the build break by converting txdma & rxdma to dma_addr_t.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: ea8daa7b97
All i2c mux users are using an explicit i2c mux core, drop support
for implicit i2c mux cores.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Add a mask to handle the case where not all child adapters should
cause a mux deselect to happen, now that there is a common deselect op
for all child adapters.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All i2c-muxes have a parent adapter and one or many child
adapters. A mux also has some means of selection. Previously,
this was stored per child adapter, but it is only needed
to keep track of this per mux.
Add an i2c mux core, that keeps track of this consistently.
Also add some glue for users of the old interface, which will
create one implicit mux core per child adapter.
Signed-off-by: Peter Rosin <peda@axentia.se>
Tested-by: Antti Palosaari <crope@iki.fi>
Tested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions: i2c_parse_fw_timings().
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add helper functions for control, data and status register access.
This simplifies the code and makes the purpose of the register
access clearer.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rename the [read|write]_sw functions to make it clearer they access
the TWSI registers.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No functional change, just moving the functions upward in
preparation of improving the recovery.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert the adapter timeout to 2 ms independently of depending on CONFIG_HZ.
CONFIG_HZ is 100 for MIPS Cavium-Octeon so the timeout value is not changed.
Also set retries to 5 to improve robustness.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable multi-master mode in I2C_CNFG reg based on hw features.
Using single/multi-master mode bit introduced for Tegra210,
whereas multi-master mode is enabled by default in HW for T124 and
earlier Tegra SOC. Enabling this bit doesn't explicitly start
treating the bus has having multiple masters, but will start
checking for arbitration lost and reporting when it occurs.
The Tegra210 I2C controller supports single/multi master mode.
Add chipdata for Tegra210 and its compatibility string so that
Tegra210 will select data that enables multi master mode correctly.
Do below prerequisites for multi-master bus if "multi-master"
dt property entry is added.
1. Enable 1st level clock always set.
2. Disable 2nd level clock gating (slcg which
is supported from T124 SOC and later chips)
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel DNV has the same iSMT SMBus host controller than Intel Avoton. Add
DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Broadcom Vulcan ARM64 processor uses the same I2C controller
present on the Broadcom XLP9xx/5xx MIPS processor family.
Updated the Kconfig by adding ARCH_VULCAN option.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow runtime PM so that PM and PCI core can put the device into low-power
state when idle and resume it back when needed in those platforms that
support PM for i801 device.
Enable also autosuspend with 1 second delay in order to not needlessly
toggle power state on and off if there are multiple transactions during
short time.
Device is resumed at the beginning of bus access and marked idle ready
for autosuspend at the end of it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Stop using legacy PCI PM support and convert to standard dev_pm_ops.
This provides more straightforward path to add runtime PM.
While at it remove explicit PCI power state control and configuration space
save/restore as the PCI core does it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When using a certain I2C device with runtime PM enabled on
a certain I2C bus adaper the following happens:
struct amba_device *foo
\
struct i2c_adapter *bar
\
struct i2c_client *baz
The AMBA device foo has its device PM struct set to ignore
children with pm_suspend_ignore_children(&foo->dev, true).
This makes runtime PM work just fine locally in the driver:
the fact that devices on the bus are suspended or resumed
individually does not affect its operation, and the hardware
does not power up unless transferring messages.
However this child ignorance property is not inherited into
the struct i2c_adapter *bar.
On system suspend things will work fine.
On system resume the following annoying phenomenon occurs:
- In the pm_runtime_force_resume() path of
struct i2c_client *baz, pm_runtime_set_active(&baz->dev); is
eventually called.
- This becomes __pm_runtime_set_status(&baz->dev, RPM_ACTIVE);
- __pm_runtime_set_status() detects that RPM state is changed,
and checks whether the parent is:
not active (RPM_ACTIVE) and not ignoring its children
If this happens it concludes something is wrong, because
a parent that is not ignoring its children must be active
before any children activate.
- Since the struct i2c_adapter *bar does not ignore
its children, the PM core thinks that it must indeed go
online before its children, the check bails out with
-EBUSY, i.e. the i2c_client *baz thinks it can't work
because it's parent is not online, and it respects its
parent.
- In the driver the .resume() callback returns -EBUSY from
the runtime_force_resume() call as per above. This leaves
the device in a suspended state, leading to bad behaviour
later when the device is used. The following debug
print is made with an extra printg patch but illustrates
the problem:
[ 17.040832] bh1780 2-0029: parent (i2c-2) is not active
parent->power.ignore_children = 0
[ 17.040832] bh1780 2-0029: pm_runtime_force_resume:
pm_runtime_set_active() failed (-16)
[ 17.040863] dpm_run_callback():
pm_runtime_force_resume+0x0/0x88 returns -16
[ 17.040863] PM: Device 2-0029 failed to resume: error -16
Fix this by letting all struct i2c_adapter:s ignore their
children: i2c children have no business doing keeping
their parents awake: they are completely autonomous
devices that just use their parent to talk, a usecase
which must be power managed in the host on a per-message
basis.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure we avoid a division-by-zero OOPS in case clock-frequency is
set too low in DT. Add missing '\n' while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Axel Lin <axel.lin@ingics.com>
This reverts commit 34cf2acdaf. 'ret' is
not set when bailing out. Also, there is a better place to check for 0.
Reported-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure we don't OOPS in case clock-frequency is set to 0 in a DT. The
variable set here is later used as a divisor.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sysfs attributes should use the same format for reads and writes,
rather than pretty-printing on read.
* Make the "cur_master" attribute read back as just the name of the
master
* Expose the list of all masters as a read-only "available_masters"
attribute, using space separators as in similar attributes of other
devices
Also, spell out "cur_master" in full as "current_master".
Fixes: 50a5ba8769 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jan reported this:
===
After enabling CONFIG_I2C_DEBUG_CORE my system was broken
(no network, console login not possible). System log was
flooded with the this message:
...
[ 608.052077] rtc-ds1307 0-0068: uevent
[ 608.052500] rtc-ds1307 0-0068: uevent
[ 608.052925] rtc-ds1307 0-0068: uevent
...
The culprit is the dev_dbg printk in the i2c uevent handler.
If this is activated (for instance by CONFIG_I2C_DEBUG_CORE)
it results in an endless loop with systemd-journald.
This happens if user-space scans the system log and reads the uevent
file to get information about a newly created device, which seems fair
use to me. Unfortunately reading the "uevent" file uses the same
function that runs for creating the uevent for a new device,
generating the next syslog entry.
Ideally user-space would implement a recursion detection and
after reading the same device file for the 1000th time call it a
day, but nevertheless I think we should avoid this problem by
removing the debug print completely or using another print variant.
The same problem seems to be reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=76886
===
His patch converted the message to pr_debug, but I think the debug can
simply go. We have other means to see code paths these days. This
enables us to clean up the function some more while we are here.
Reported-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Pull i2c updates from Wolfram Sang:
"Mostly usual driver updates and improvements. The changelog should
give an idea. Standing out is the i2c-qup driver with lots of new
capabilities and we also have now an i2c-demuxer.
I'd especially like to welcome Peter Rosin as the i2c-mux maintainer.
He has an interesting series for muxes in the queue and agreed to look
after this part of the subsystem. Thank you, Peter, and welcome
again!
The octeon changes were applied pretty recently before the merge
window. I am aware. They are the first (and relatively simple)
patches of a larger overhaul to this driver. In case something goes
wrong with them, they are easy to fix (or revert). The advantage I
see is that they are out of the way, and I can concentrate on the next
block of patches. I really would like to apply the overhaul in
smaller batches to avoid regressions. And waiting a cycle for the
introductory patches seemed too much of a delay for me"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: octeon: Support I2C_M_RECV_LEN
i2c: octeon: Cleanup resource allocation code
i2c: octeon: Cleanup i2c-octeon driver
MAINTAINERS: add Peter Rosin as i2c mux maintainer
dt-bindings: i2c: Spelling s/propoerty/property/
i2c: immediately mark ourselves as registered
i2c: i801: sort IDs alphabetically
MAINTAINERS: Mika and me are designated reviewers for I2C DESIGNWARE
i2c: octeon: Cleanup kerneldoc comments
i2c: do not use internal data from driver core
i2c: cadence: Fix the kernel-doc warnings
i2c: imx: remove extra spaces.
i2c: rcar: don't open code of_device_get_match_data()
i2c: qup: Fix fifo handling after adding V2 support
i2c: xiic: Implement power management
i2c: piix4: Pre-shift the port number
i2c: piix4: Always use the same type for port
i2c: piix4: Support alternative port selection register
i2c: tegra: don't open code of_device_get_match_data()
i2c: riic, sh_mobile, rcar: Use ARCH_RENESAS
...
If I2C_M_RECV_LEN is set consider the length byte.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove resource values from struct i2c_octeon and use
devm_ioremap_resource helper.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cleanup only without functional change.
- removed DRV_VERSION
- defines: use defines instead of plain values,
use BIT_ULL macro, add comments
- rename waitqueue return value to time_left
- sort local variables by length
- fix indentation and whitespace errors
- make function return void if the result is not used
(octeon_i2c_stop, octeon_i2c_set_clock)
- remove debug code from octeon_i2c_stop
- renamed some functions for readability
- update copyright
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mark the i2c bus as registered right after the the bus_register call,
not at the end of init. Otherwise, we can't register our own dummy
driver.
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 95026658c4 ("i2c: do not use internal data from driver core")
Sort the list to have a faster search for a certain PCI ID.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove point after parameter description and replace kerneldoc
by a comment if it has no additional no value.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The variable p is a data structure which is used by the driver core
internally and it is not expected that busses will be directly accessing
these driver core internal only data.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[wsa: removed the unlikely()]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes the below warnings
drivers/i2c/busses/i2c-cadence.c:164: warning: No description found for parameter 'dev'
drivers/i2c/busses/i2c-cadence.c:826: warning: No description found for parameter 'dev'
drivers/i2c/busses/i2c-cadence.c:826: warning: Excess function parameter '_dev' description in 'cdns_i2c_runtime_suspend'
drivers/i2c/busses/i2c-cadence.c:844: warning: No description found for parameter 'dev'
drivers/i2c/busses/i2c-cadence.c:844: warning: Excess function parameter '_dev' description in 'cdns_i2c_runtime_resume'
while at it also update the cdns_i2c_clear_bus_hold
and the runtime function update.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device HID AMDI0010 to match the AMD ACPI Vendor ID (AMDI) that
was registered in http://www.uefi.org/acpi_id_list, and the I2C
controller on future AMD paltform will use the HID instead of AMD0010.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After the addition of V2 support, there was a regression observed
when testing it on MSM8996. The reason is driver puts the controller
in to RUN state and writes the data to be 'tx' ed in fifo. But controller
has to be put in to 'PAUSE' state and data has to written to fifo. Then
should be put in to 'RUN' state separately.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable power management. This patch enables the clocks before transfer
and disables after the transfer. It also adds the clock description.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We want the size of the struct, not of a pointer to it. To be future
proof, just dereference the pointer to get the desired type.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Shift the port number at initialization time, so that it is ready to
use at run time. That way we don't have to do it again for every SMBus
transaction.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sometimes u8 is used to store the port number, sometimes unsigned
short is used. Consistently stick to a single type, for consistency
and to avoid implicit casts.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 register reference guide says that the SMBus port selection
bits may not always be in register Smbus0En (0x2c) but could
alternatively be found in register Smbus0Sel (0x2e) depending on the
settings in register Smbus0SelEn (0x2f.) Add support for this
configuration.
The "alternative" register is the only one working for the Bolton
(aka Hudson-2) chipset anyway. I do not have any documentation for
the "kerncz" chipset so we treat it the same as the Bolton for now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Laxman Dewangan <ldewangan@nvidia.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
QUP cores can be attached to a BAM module, which acts as
a dma engine for the QUP core. When DMA with BAM is enabled,
the BAM consumer pipe transmitted data is written to the
output FIFO and the BAM producer pipe received data is read
from the input FIFO.
With BAM capabilities, qup-i2c core can transfer more than
256 bytes, without a 'stop' which is not possible otherwise.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog
resources have been moved to reside under the i801 SMBus host
controller whereas previously they were under the LPC device.
This patch adds Intel lewisburg SMBus support for iTCO device.
It allows to load watchdog dynamically when the hardware is
present.
Fixes: cdc5a3110e ("i2c: i801: add Intel Lewisburg device IDs")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The current iProc I2C driver only allows each TX transfer up to 63
bytes (the TX FIFO has a size of 64 bytes, and one byte is reserved
for slave address). This patch enhances the driver to support TX
transfer in each I2C message for up to 65535 bytes (a practical
maximum, since member 'max_write_len' of 'struct i2c_adapter_quirks is
of type 'u16')
This works by loading up the I2C TX FIFO and enabling the TX underrun
interrupt for each burst. After each burst of TX data is finished,
i.e., when the TX FIFO becomes empty, the TX underrun interrupt will be
triggered and another burst of TX data can be loaded into the TX FIFO.
This repeats until all TX data are finished
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Icarus Chau <ichau@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix typo in the driver from 'I2C_TIMEOUT_MESC' to 'I2C_TIMEOUT_MSEC'
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If 4GB mode is enabled, we should add 4GB DMA mode support in i2c
driver. Set 4GB mode register to support 4GB mode.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There can be unnecessary runtime suspend-resume cycle during
i2c-designware-platdrv probe when it registers the I2C adapter device. This
happens because i2c-designware-platdrv is set to initially active platform
device in its probe function and is a parent of I2C adapter.
In that case power.usage_count of i2c-designware device is zero and
pm_runtime_get()/pm_runtime_put() cycle during probe could put it into
runtime suspend. This happens when the i2c_register_adapter() calls the
device_register():
i2c_register_adapter
device_register
device_add
bus_probe_device
device_initial_probe
__device_attach
if (dev->parent) pm_runtime_get_sync(dev->parent)
...
if (dev->parent) pm_runtime_put(dev->parent)
After that the i2c_register_adapter() continues registering I2C slave
devices. In case slave device probe does I2C transfers the parent will
resume again and thus get a needless runtime suspend/resume cycle during
adapter registration.
Prevent this while retaining the runtime PM status of i2c-designware by
only incrementing/decrementing device power usage count during I2C
adapter registration. That makes sure there won't be spurious runtime PM
status changes and lets the driver core to idle the device after probe
finishes.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-designware-platform module has duplicate module information
when CONFIG_I2C_DESIGNWARE_BAYTRAIL is set. It gets the information
from both i2c-designware-platdrv and i2c-designware-baytrail. The
latter is optional extra code which ends up in the same module so it
should not export module information.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The per adapter bus_lock already projects from concurrent calls to the
master_xfer callback. No need to add a driver internal lock.
Also, rephrase a comment to drop mention of this lock.
Reported-by: Rongrong Zou <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The definition of i2c_msg says that
"If this is the last message in a group, it is followed by a STOP.
Otherwise it is followed by the next @i2c_msg transaction segment,
beginning with a (repeated) START"
So the expectation is that there is no 'STOP' bit inbetween individual
i2c_msg segments with repeated 'START'. Adding the support for the same.
This is required for some clients like touchscreen which keeps
incrementing counts across individual transfers and 'STOP' bit inbetween
resets the counter, which is not required.
This patch adds the support in non-dma mode.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
QUP from version 2.1.1 onwards, supports a new format of
i2c command tags. Tag codes instructs the controller to
perform a operation like read/write. This new tagging version
supports bam dma and transfers of more than 256 bytes without 'stop'
in between. Adding the support for the same.
For each block a data_write/read tag and data_len tag is added to
the output fifo. For the final block of data write_stop/read_stop
tag is used.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
qup_wait_writeready waits only on a output fifo empty event.
Change the same function to accept the event and data length
to wait as parameters. This way the same function can be used for
timeouts in other places as well.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver allows an I2C bus to switch between multiple masters. This
is not hot-switching because connected I2C slaves will be
re-instantiated. It is meant to select the best I2C core at runtime once
the task is known. Example: Prefer i2c-gpio over another I2C core
because of HW errata affecting your use case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C bus names are supposed to be stable as they can be used by
userspace to uniquely identify a specific I2C bus. So restore the
original names for all legacy (pre-SB800) devices.
For SB800 devices and later, improve the names. "SDA" refers to the
serial data pin of each SMBus port, it's an implementation detail the
user doesn't need to know. Use "port" instead, which is easier to
understand.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is effectively reapplies the commit b0898fdaff ("i2c: designware-pci: use
IRQF_COND_SUSPEND flag") after the commit d80d134182 ("i2c: designware: Move
common probe code into i2c_dw_probe()"). Original message as follows.
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Fixes: d80d134182 (i2c: designware: Move common probe code into i2c_dw_probe())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This closes a race window where I2C device drivers attempt to access
I2C buses which aren't fully initialized yet.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need a single mutex for all 4 shared SMBus ports on the SB800. A
per-port mutex doesn't protect us from concurrent access.
In theory the mutex should be per PCI device, however in practice we
know that there's only ever a single instance of the device in a given
system so we can use a global.
Also take the mutex during initialization, as first port may be already
in use when second port is initialized.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: made mutex static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Quite some driver updates:
- piix4 can now handle multiplexed adapters
- brcmstb, xlr, eg20t, designware drivers support more SoCs
- emev2 gained i2c slave support
- img-scb and rcar got bigger refactoring to remove issues
- lots of common driver updates
i2c core changes:
- new quirk flag when an adapter does not support clock stretching,
so clients can be configured to avoid that if possible
- added a helper function to retrieve timing parameters from firmware
(with rcar being the first user)
- "multi-master" DT binding added so drivers can adapt to this
setting (like disabling PM to keep arbitration working)
- RuntimePM for the logical adapter device is now always enabled by
the core to ensure propagation from childs to the parent (the HW
device)
- new macro builtin_i2c_driver to reduce boilerplate"
* 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: create builtin_i2c_driver to avoid registration boilerplate
i2c: imx: fix i2c resource leak with dma transfer
dt-bindings: i2c: eeprom: add another EEPROM device
dt-bindings: move I2C eeprom descriptions to the proper file
i2c: designware: Do not require clock when SSCN and FFCN are provided
DT: i2c: trivial-devices: Add Epson RX8010 and MPL3115
i2c: s3c2410: remove superfluous runtime PM calls
i2c: always enable RuntimePM for the adapter device
i2c: designware: retry transfer on transient failure
i2c: ibm_iic: rename i2c_timings struct due to clash with generic version
i2c: designware: Add support for AMD Seattle I2C
i2c: imx: Remove unneeded comments
i2c: st: use to_platform_device()
i2c: designware: use to_pci_dev()
i2c: brcmstb: Adding support for CM and DSL SoCs
i2c: mediatek: fix i2c multi transfer issue in high speed mode
i2c: imx: improve code readability
i2c: imx: Improve message log when DMA is not used
i2c: imx: add runtime pm support to improve the performance
i2c: imx: init bus recovery info before adding i2c adapter
...
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
* device-properties:
device property: avoid allocations of 0 length
device property: the secondary fwnode needs to depend on the primary
device property: add spaces to PROPERTY_ENTRY_STRING macro
include/linux/property.h: fix build issues with gcc-4.4.4
i2c: designware: Convert to use unified device property API
mfd: intel-lpss: Pass HSUART configuration via properties
mfd: intel-lpss: Pass SDA hold time to I2C host controller driver
mfd: intel-lpss: Add support for passing device properties
mfd: core: propagate device properties to sub devices drivers
driver core: Do not overwrite secondary fwnode with NULL if it is set
driver core: platform: Add support for built-in device properties
device property: Take a copy of the property set
device property: Fallback to secondary fwnode if primary misses the property
device property: return -EINVAL when property isn't found in ACPI
device property: improve readability of macros
device property: helper macros for property entry creation
device property: keep single value inplace
device property: refactor built-in properties support
device property: rename helper functions
device property: always check for fwnode type
In i2c_imx_dma_xfer(), when dmaengine_submit() returns error,
the context goto label err_submit and then return. However, the
memory allocated for txdesc has not been freed yet, which
leads to resource leak.
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current driver uses input clock source frequency to calculate
values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not
currently have a good way to provide the frequency information.
Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used
to directly provide these values. So, the clock information should
no longer be required during probing.
However, since clk can be invalid, additional checks must be done where
we are making use of it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Loc Ho <lho@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
RuntimePM of the adapter device is now taken care of by the core. So, we
can remove these calls.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The adapter device is a logical device. Because of that, it already uses
pm_runtime_no_callbacks() in the core. To ensure proper propagation from
the children (i2c devices) to the parent of the adapter (the HW device),
make sure RuntimePM is enabled in any case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the i2c_adapter retries field to a sensible value. This allows the i2c core
to retry master_xfer() when it returns -EAGAIN. Currently the i2c-designware
driver returns -EAGAIN only on Tx arbitration failure (DW_IC_TX_ARB_LOST).
Reported-by: Rolland Chau <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable APM X-Gene ACPI I2C device support by adding the
corresponding ACPI ID. The platform ACPI APD corresponding
change is required to provide the proper clock frequency input.
Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes: e1dba01ca6 ("i2c: add generic routine to parse DT for timing information")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device HID AMDI0510 to match the I2C controlers on AMD Seattle platform
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These multi-lines comments do not follow the standard kernel coding
style. In fact, they are not useful comments, so get rid of them.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Broadcoms DSL, CM (cable modem)and STB I2C core implementation have
8 data in/out registers that can transfer 8 bytes or 32 bytes max.
Cable and DSL "Peripheral" i2c cores use single byte per data
register and the STB can use 4 byte per data register transfer.
Adding support to take care of this difference. Accordingly added
the compatible string for SoCs using the "Peripheral" I2C block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For mt8173 platform with auto restart support, when doing i2c multi
transfer in high speed, we should ignore the first restart irq after
the master code, otherwise the first transfer will be discarded.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace of_get_named_gpio_flags with of_get_named_gpio because
the latter has less parameters, which improves code readability.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When DMA cannot be used, it is better to state that the I2C controller
will operate in PIO mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In our former i2c driver, i2c clk is enabled and disabled in
xfer function, which contributes to power saving. However,
the clk enable process brings a busy wait delay until the core
is stable. As a result, the performance is sacrificed.
To weigh the power consumption and i2c bus performance, runtime
pm is the good solution for it. The clk is enabled when a i2c
transfer starts, and disabled after a specifically defined delay.
If CONFIG_PM is disabled the net result of this patch is that the
clock is never disabled.
Without the patch the test case (many eeprom reads) executes with approx:
real 1m7.735s
user 0m0.488s
sys 0m20.040s
With the patch the same test case (many eeprom reads) executes with approx:
real 0m54.241s
user 0m0.440s
sys 0m5.920s
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: sorted includes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In multi master mode, the IP core needs to be always active for
arbitration reasons. Get the config from DT and set up PM depending on
the config.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These macros don't really hide complexity, but C idioms. Removing them
makes the code easier to read IMO and make a planned extension easier.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In version 3.3 of the IP when transaction halt is set, an interrupt
will be generated after each byte of a transfer instead of after
every transfer but before the stop bit.
Due to this behaviour we have to be careful that every time we
release the transaction halt we have to re-enable it straight away
so that we only process a single byte, not doing so will result in
all remaining bytes been processed and a stop bit being issued,
which will prevent us having a repeated start.
This change will have no effect on earlier versions of the IP.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Master halt is issued after each byte of a transaction is processed in
IP version 3.3.
Master halt will stall the bus by holding the SCK line low until the
halt bit in the scb_general_control is cleared.
After the last byte of a transfer is processed we can use the Master
Halt interrupt to facilitate a repeated start transfer without
issuing a stop bit.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Stop Detected interrupt is triggered when a Stop bit is detected on
the bus, which indicates the end of the current transfer.
When the end of a transfer is indicated by the Stop Detected interrupt,
drain the FIFO and signal completion for the transaction.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we are using the transaction halt interrupt to safely control
repeated start transfers, we no longer need to handle the fifo
emptying interrupts.
Handling this interrupt along with Transaction Halt interrupt can
cause erratic behaviour.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds support for the I2C_M_IGNORE_NAK protocol
modification.
Such behaviour can only be implemented in atomic mode. So, if a
transaction contains a message with such flag the drivers
switches to atomic mode. The implementation consists simply in
treating NAKs as ACKs.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This function used to be DT only, so it lived inside a CONFIG_OF block.
Now it uses device attributes and must be moved outside of it. No
further code changes, only one whitespace improvement.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Sigma Designs variant of this controller has the ability to generate
interrupts. This is controlled using two additional registers, oddly
enough overlapping with the defined but unused HDSTATIM.
This patch adds support for using this feature instead of busy-looping
if an IRQ is specified.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BYTECNT register holds the transfer size minus one. Setting it to
the correct value removes the need for a dummy read/write at the end of
each transfer. As zero-length transfers are not supported, do not
advertise I2C_FUNC_SMBUS_QUICK.
In other words, this patch makes the driver transfer the number of bytes
requested unless this is zero, which is not supported by the hardware
and is thus refused.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sigma Designs chips use a variant of this controller with the following
differences:
- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts
This patch adds support for the first two of these. It also calculates
and sets the correct clock divisor if a clk is provided. The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions. Plain convert, no functionality
added yet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and
extended. See built-in docs for further information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.
This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because of some hardware limitation, AMD I2C controller can't
trigger pending interrupt if interrupt status has been changed
after clearing interrupt status bits. Then, I2C will lost
interrupt and IO timeout.
According to hardware design, this patch implements a workaround
to disable i2c controller interrupt and re-enable i2c interrupt
before exiting ISR.
To reduce the performance impacts on other vendors, use unlikely
function to check flag in ISR.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI _DSD (introduced in ACPI v5.1) it is now possible to pass device
configuration information from ACPI in addition to DT. In order to support
this, convert the driver to use the unified device property accessors
instead of DT specific.
Change to ordering a bit so that we first try platform data and if that's
not available look from device properties. ACPI *CNT methods are then used
as last resort to override everything else.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For platform with auto restart support, between every transfer,
i2c controller will trigger an interrupt and SW need to handle
it to start new transfer. When doing write-then-read transfer,
instead of restart mechanism, using WRRD mode to have controller
send both transfer in one request to reduce latency.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported in the links given below. the BCM2835 has a hardware bug in
its i2c module which prevents a correct clock stretching. This patch
adds the I2C_AQ_NO_CLK_STRETCH quirk flag to i2c-bcm2835.
Signed-off-by: Nicola Corna <nicola@corna.info>
[wsa: put the links into the code as comments]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH to drivers/i2c/algos/i2c-algo-bit.c when getscl
is not available.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All protected sections are only called from sleep-able context, so there is
no need to use a spinlock.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtou8.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C controller used in Keystone SoC has an undocumented peculiarity which
results in SDA-SCL margins being dependent on module clock. Driving high
capacity bus near its limits can result in STOP condition sometimes being
understood as REPEATED-START by slaves (or NACK instead of ACK, etc...).
Driving the module with higher clocks increases the margin between SDA and SCL
transitions, making the operations with higher bus rates more robust. Therefore,
target the module clock to 12MHz instead of 7MHz, still staying within
the specification limits.
Before the change STOP timing looked like this on 400kHz:
SDA ----------+ +----
\ /
\ /
+----+
(1)
SCL --+ +------------
\ /
\ /
+----+
(2)
While only point (1) signals STOP, point (2) could be incorrectly recognized as
repeated-START (almost no margin between SDA and SCL transitions).
After the change there is at least 600ns margin measured between SCL fall and
SDA fall during STOP generation:
SDA ------+ +----
\ /
\ /
+----+
SCL --+ +--------
\ /
\ /
+----+
->| |<- 600ns
->| |<- tSUSTO
So called tSUSTO (setup time for STOP condition) is still slightly higher than
600ns, so no problem here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes obvious copy-past error in wake up irq parsing
code which leads to the fact that dev_pm_set_wake_irq() will
be called with wrong IRQ number when "wakeup" IRQ is not
defined in DT.
Fixes: 3fffd12839 ("i2c: allow specifying separate wakeup interrupt in device tree")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org> # v4.3
Pull i2c updates from Wolfram Sang:
- New drivers: UniPhier (with and without FIFO)
- some drivers got some bigger rework: ismt, designware, img-scb (rcar
had to be reverted because issues were showing up just lately)
- ACPI: reworked the device scanning and added support for muxes
... and quite a lot of driver bugfixes and cleanups this time. All
files touched outside of the i2c realm have proper acks.
* 'i2c/for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: rcar: Revert the latest refactoring series
i2c: pnx: remove superfluous assignment
MAINTAINERS: i2c: drop i2c-pnx maintainer
MAINTAINERS: i2c: mark also subdirectories as maintained
i2c: cadence: enable driver for ARM64
i2c: i801: Document Intel DNV and Broxton
i2c: at91: manage unexpected RXRDY flag when starting a transfer
i2c: pnx: Use setup_timer instead of open coding it
i2c: add ACPI support for I2C mux ports
acpi: add acpi_preset_companion() stub
i2c: pxa: Add support for pxa910/988 & new configuration features
i2c: au1550: Convert to devm_kzalloc and devm_ioremap_resource
i2c-dev: Fix I2C_SLAVE ioctl comment
i2c-dev: Fix typo in ioctl name reference
i2c: sirf: tune the divider to make i2c bus freq more accurate
i2c: imx: Use -ENXIO as error in the NACK case
i2c: i801: Add support for Intel Broxton
i2c: i801: Add support for Intel DNV
i2c: mediatek: add i2c resume support
i2c: imx: implement bus recovery
...
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
This whole series caused sometimes timeouts and even OOPSes on some
r8a7791 Koelsch boards. We need to understand and fix those first.
Revert "i2c: rcar: clean up after refactoring"
Revert "i2c: rcar: revoke START request early"
Revert "i2c: rcar: check master irqs before slave irqs"
Revert "i2c: rcar: don't issue stop when HW does it automatically"
Revert "i2c: rcar: init new messages in irq"
Revert "i2c: rcar: refactor setup of a msg"
Revert "i2c: rcar: remove spinlock"
Revert "i2c: rcar: remove unused IOERROR state"
Revert "i2c: rcar: rework hw init"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Use timer API function setup_timer instead of init_timer to
initialize the timer.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although I2C mux devices are easily enumerated using ACPI (_HID/_CID or
device property compatible string match), enumerating I2C client devices
connected through an I2C mux needs a little extra work.
This change implements a method for describing an I2C device hierarchy that
includes mux devices by using an ACPI Device() for each mux channel along
with an _ADR to set the channel number for the device. See
Documentation/acpi/i2c-muxes.txt for a simple example.
To make this work the ismt, i801, and designware pci/platform devs now
share an ACPI companion with their I2C adapter dev similar to how it's done
in OF. This is done on the assumption that power management functions will
not be called directly on the I2C dev that is sharing the ACPI node.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
TWSI_ILCR & TWSI_IWCR registers are used to adjust clock rate
of standard & fast mode in pxa910/988; so this patch adds these two new
entries to "struct pxa_reg_layout" and "struct pxa_i2c".
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: white space fixes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* APIs to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The first part of the comment is wrong since November 2007, delete it.
The second part of the comment is related to I2C_PEC, not I2C_SLAVE, so
move it where it belongs.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ioctl is named I2C_RDWR for "I2C read/write". But references to it
were misspelled "rdrw". Fix them.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In prima2 and atlas7, due to some hardware design issue. we
need to adjust the divider ratio a little according to i2c
bus frequency ranges.
Since i2c is open drain interface that allows the slave to
stall the transaction by holding the SCL line at '0', the RTL
implementation is waiting for SCL feedback from the pin after
setting it to High-Z ('1'). This wait adds to the high-time
interval counter few cycles of the input synchronization
(depending on the SCL_FILTER_REG field), and also the time it
takes for the board pull-up resistor to rise the SCL line.
For slow SCL settings these additions are negligible, but they
start to affect the speed when clock is set to faster frequencies.
This patch is based on the actual tests, and it makes SCL more
accurate.
Signed-off-by: Guoying Zhang <Guoying.Zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver can not be used on a platform with common clock framework
until clk_prepare/clk_unprepare calls are added, otherwise clk_enable
calls will fail and a WARN is generated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/i2c/fault-codes the response to a bus NACK
should be -ENXIO, so fix the error code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBUS PCI ID of Intel Broxton.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mt65xx i2c controller initial setting will be cleared after system suspend,
so we should init mt65xx i2c controller again when system resume.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The patch reverts commit a445900c90 (i2c: designware: Add support for
AMD I2C controller). It never worked anyhow because it did not register
a proper clkdev.
Since kernel 4.1 starts to support APD, there is no need to get freq
from id->driver_data for AMD0010. clkdev is supposed to be already
registered in APD.
So, revert old design and make AMD0010 looks like other ones.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases a NACK interrupt may be pending in the Status Register (SR)
as a result of a previous transfer. However at91_do_twi_transfer() did not
read the SR to clear pending interruptions before starting a new transfer.
Hence a NACK interrupt rose as soon as it was enabled again at the I2C
controller level, resulting in a wrong sequence of operations and strange
patterns of behaviour on the I2C bus, such as a clock stretch followed by
a restart of the transfer.
This first issue occurred with both DMA and PIO write transfers.
Also when a NACK error was detected during a PIO write transfer, the
interrupt handler used to wrongly start a new transfer by writing into the
Transmit Holding Register (THR). Then the I2C slave was likely to reply
with a second NACK.
This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY
status bit only if both the TXCOMP and NACK status bits are cleared.
Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91
kernel image. Adapted to linux-next.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Commit ("i2c: designware: Rename platform driver probe and PM
functions") introduced "'dw_i2c_plat_prepare' undeclared here" and
"'dw_i2c_plat_complete' undeclared here" build errors when
CONFIG_PM_SLEEP is not set.
Fix this by renaming NULL defined dw_i2c_prepare and dw_i2c_complete PM
hooks to dw_i2c_plat_prepare and dw_i2c_plat_complete since this was
obviously missing from the commit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 00d8689b85 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.
This commit fixes that problem by removing the bogus "return false".
Fixes: 00d8689b85 ("i2c: mv64xxx: rework offload support to fix several problems")
Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: removed now unused ret value and cast to proper enum type]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-au1550 driver has to program various setup and hold times
for the sda/scl signals by hand. The current values seem to be
working best when the driver is supplied with 50MHz, however on the
DB1300 board 48MHz is the closest we can get to it, and the timings
are a bit too tight for that, leading to the last bit of a transmission
sometimes being swallowed. This manifests itself in wrong readings
of the ne1619 sensor and inability to configure the wm8731 i2s codec.
With the relaxed timings, both the sensor and the i2s codec can now
be accessed more reliably over a wider range of I2C block input
frequencies.
Verified on DB1200, DB1300 and DB1550 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This code is repeated in probe:
i2c_dev->adapter.algo = &tegra_i2c_algo;
Cc: Donglin Peng <pengdonglin137@163.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.
module clock frequency
master clock frequency = ----------------------
(ICCL + 6) + (ICCH + 6)
It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.
Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Issue the warning in all error paths when unable to register MSI or its
handler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Propagate actual return code when requesting interrupt fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct pci_dev already has a flag to track if MSI is enabled or not. Use it
directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to repeat the work that is already done in the PCI driver
core. Remove suspend and resume callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pcim_release() will release any requested region. There is no need to duplicate
this effort in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The way we currently scan I2C devices behind an I2C host controller does not
work in cases where the I2C device in question is not declared directly below
the host controller ACPI node.
This is perfectly legal according the ACPI 6.0 specification and some existing
systems are doing this.
To be able to enumerate all devices which are connected to a certain I2C host
controller we need to rework the current I2C scanning routine a bit. Instead of
scanning directly below the host controller we scan the whole ACPI namespace
for present devices with valid I2cSerialBus() connection pointing to the host
controller in question.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@kernel.org
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There is some code duplication in i2c-designware-platdrv and
i2c-designware-pcidrv probe functions. What is even worse that duplication
requires i2c_dw_xfer(), i2c_dw_func() and i2c_dw_isr() i2c-designware-core
functions to be exported.
Therefore move common code into new i2c_dw_probe() and make functions above
local to i2c-designware-core.
While merging the code patch does following functional changes:
- I2C Adapter name will be "Synopsys DesignWare I2C adapter". Previously it
was used for platform and ACPI devices but PCI device used
"i2c-designware-pci".
- Using device name for interrupt name. Previous it was platform device name,
ACPI device name or "i2c-designware-pci".
- Error code from devm_request_irq() and i2c_add_numbered_adapter() will be
printed in case of error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it easier to distinguish between i2c-designware-platdrv and
i2c-designware-core functions and to be consistent with
i2c-designware-pcidrv.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dw_readl() and dw_writel() are not used outside of i2c-designware-core and
they are not exported so make them static and remove their forward
declaration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_dw_is_enabled() became unused by the commit be58eda775
("i2c: designware-pci: Cleanup driver power management") and
i2c_dw_enable() by the commit 3a48d1c08f ("i2c: prevent spurious
interrupt on Designware controllers").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device must not generate interrupts before registering the interrupt
handler so move i2c_dw_disable_int() before requesting it.
There are no known issues with this. The code has been here since commit
fe20ff5c7e ("i2c-designware: Add support for Designware core behind PCI
devices.").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to clear interrupts in i2c_dw_pci_probe() since only place
where interrupts are unmasked is i2c_dw_xfer_init() and there interrupts
are always cleared after commit 2a2d95e9d6 ("i2c: designware: always
clear interrupts before enabling them").
This allows to cleanup the code and replace i2c_dw_clear_int() in
i2c_dw_xfer_init() by direct register read as there are no other callers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A change of return status was introduced in commit 3fffd12839
("i2c: allow specifying separate wakeup interrupt in device tree")
The commit prevents the defer status being passed up the call stack
appropriately when dev_pm_domain_attach returns -EPROBE_DEFER.
Catch the PROBE_DEFER and clear up the IRQ wakeup status
Signed-off-by: Kieran Bingham <kieranbingham@gmail.com>
Fixes: 3fffd12839 ("i2c: allow specifying separate wakeup interrupt in device tree")
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.
If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.
Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.
Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using % can be slow depending on the architecture.
Using DIV_ROUND_UP is nicer and more efficient way to do it.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move scb_wr_rd_fence to before reading from fifo and writing to
fifo to make sure the the first read/write is done after the required
number of cycles.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code to read from the master read fifo, and write to the master
write fifo, checks a bit in an SCB register before every byte to
ensure that the fifo is not full (write fifo) or empty (read fifo).
Due to clock domain crossing inside the SCB block the updated value
of this bit is only visible after 2 cycles.
The scb_wr_rd_fence() function does 2 dummy writes (to the read-only
revision register), and it's called before reading from or writing to the
fifos to ensure that subsequent reads of the fifo status bits do not read
stale values.
As the 2 dummy writes are required in all versions of the ip, the version
check is dropped.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated. To keep the race window as small as
possible, we clear it right at the beginning of the interrupt. We don't
need checking since we always want to stop START and STOP generation on
the next occasion after we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to broken HW design, master IRQs are more timing critical, so give
them precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We make sure to reinit the HW in the timeout case; then we know that
interrupts are always disabled in the sections protected by the
spinlock. Thus, we can simply remove it which is a preparation for
further refactoring. While here, rename the timeout variable to
time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
Reading the register (if allowed) after writing is to ensure writing
is completed on a posted bus. The endianness of reading doesn't matter.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With CONFIG_OF=n, the following warnings occur when compiling
drivers/i2c/muxes/i2c-mux-reg.c:
CC drivers/i2c/muxes/i2c-mux-reg.o
drivers/i2c/muxes/i2c-mux-reg.c:170:13: warning: ‘struct gpiomux’ declared inside parameter list [enabled by default]
struct platform_device *pdev)
^
drivers/i2c/muxes/i2c-mux-reg.c:170:13: warning: its scope
is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/i2c/muxes/i2c-mux-reg.c: In function ‘i2c_mux_reg_probe’:
drivers/i2c/muxes/i2c-mux-reg.c:201:3: warning: passing argument 1 of ‘i2c_mux_reg_probe_dt’ from incompatible pointer type [enabled by default]
ret = i2c_mux_reg_probe_dt(mux, pdev);
^
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Checking was done at three different locations, just do it once and
properly at probing time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: York Sun <yorksun@freescale.com>
Every call of of_parse_phandle() increments user count of found device
node, if OF_DYNAMIC is enabled.
The change fixes all similar addressed cases in drivers/i2c.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of having each i2c driver individually parse device tree data in
case it or platform supports separate wakeup interrupt, and handle
enabling and disabling wakeup interrupts in their power management
routines, let's have i2c core do that for us.
Platforms wishing to specify separate wakeup interrupt for the device
should use named interrupt syntax in their DTSes:
interrupt-parent = <&intc1>;
interrupts = <5 0>, <6 0>;
interrupt-names = "irq", "wakeup";
This patch is inspired by work done by Vignesh R <vigneshr@ti.com> for
pixcir_i2c_ts driver.
Note that the original code tried to preserve any existing wakeup
settings from userspace but was not quite right in that regard:
it would preserve wakeup flag set by userspace upon driver rebinding;
but it would re-arm the wakeup flag if it was disabled by userspace.
We think that resetting the flag upon re-binding the driver is proper
behavior as the driver is responsible for setting up and handling
wakeups.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Vignesh R <vigneshr@ti.com>
[wsa: updated the commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The dma_mapping_error() function returns true if there is an error, it
doesn't return an error code. We should return -ENOMEM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are devices that need to handle block transactions
regardless of the capabilities exported by the adapter.
For performance reasons, they need to use i2c read blocks
if available, otherwise emulate the block transaction with word
or byte transactions.
Add support for a helper function that would read a data block
using the best transfer available: I2C_FUNC_SMBUS_READ_I2C_BLOCK,
I2C_FUNC_SMBUS_READ_WORD_DATA or I2C_FUNC_SMBUS_READ_BYTE_DATA.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Based on i2c-mux-gpio driver, similarly the register-based mux
switch from one bus to another by setting a single register.
The register can be on PCIe bus, local bus, or any memory-mapped
address. The endianness of such register can be specified in device
tree if used, or in platform data.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Address collisions will be rare, but we should let the user know that
slaves have their own address space nonetheless.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We now have seperate address spaces for 10 bit and we-are-slave clients.
Update the sysfs device instantiation method to support these types by
accepting the address offsets that are assigned to the extra address
spaces. Update the documentation, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is not enough to compare the plain address value, we also need to
check the flags enabling a different address space. E.g. it is valid to
have address 0x50 as a 7-bit address and 0x050 as 10-bit address on the
same bus. Same for addresses when we are the slave.
Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check for slave and 10-bit flags when probing and mark the client when
found. Improve the address validity check, too
Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We want to use this function with struct boardinfo soon, so let's just
pass the parameters really needed. We also extend the type of addr, so
more types can be input. Remove a superfluous dangling comment while
here.
Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current naming is based on the arguments of the functions and not on
what they do. Even I as the maintainer find this confusing, so let's
rename them to something more descriptive.
Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We want a separate address range for being an I2C slave. Add an offset
of 0x1000, so it can be combined with ten bit addresses as well. Add a
separate function to create the address value, we will need it later in
other places.
Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When occur i2c ack error, i2c controller generate two interrupts,
first is the ack error interrupt, then the complete interrupt.
i2c interrupt handler should keep the two interrupt value, and only
call complete() for the complete interrupt.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reset DMA in hardware init function to avoid unknown hardware state
before do any I2C operation.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources
have been moved to reside under the i801 SMBus host controller whereas
previously they were under the LPC device.
In order to support the iTCO watchdog on newer PCHs we need to create the
platform device here in the SMBus driver and pass all known resources using
platform data.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Minor clean up of indenting, no functional change
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[wsa: squashed two lines into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The owner of the adapter is missing, while this driver is tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Printing adapter name is irrelevant from this debug print and makes output
needlessly long. Having already device and functions names printed here is
enough for debugging.
While at it remove extra space from "enabled= 0x" and use "%#x" for
printing "0x" prefixed hexadecimal values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made it a oneliner]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This change is needed to properly lock I2C parent bus driver.
Prior to this change i2c_put_adapter() is misused, which may lead
to an overflow over zero of I2C bus driver user counter.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
of_find_i2c_adapter_by_node() call requires quite often missing
put_device(), and i2c_put_adapter() releases a device locked by
i2c_get_adapter() only. In general module_put(adapter->owner) and
put_device(dev) are not interchangeable.
This is a common error reproduction scenario as a result of the
misusage described above (for clearness this is run on iMX6 platform
with HDMI and I2C bus drivers compiled as kernel modules):
root@mx6q:~# lsmod | grep i2c
i2c_imx 10213 0
root@mx6q:~# lsmod | grep dw_hdmi_imx
dw_hdmi_imx 3631 0
dw_hdmi 11846 1 dw_hdmi_imx
imxdrm 8674 3 dw_hdmi_imx,imx_ipuv3_crtc,imx_ldb
drm_kms_helper 113765 5 dw_hdmi,imxdrm,imx_ipuv3_crtc,imx_ldb
root@mx6q:~# rmmod dw_hdmi_imx
root@mx6q:~# lsmod | grep i2c
i2c_imx 10213 -1
^^^^^
root@mx6q:~# rmmod i2c_imx
rmmod: ERROR: Module i2c_imx is in use
To fix existing users of these interfaces and to avoid any further
confusion and misusage in future, add one more interface
of_get_i2c_adapter_by_node(), it is similar to i2c_get_adapter() in
sense that an I2C bus device driver found and locked by user can be
correctly unlocked by i2c_put_adapter().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In addition to module_get()/module_put() add get_device()/put_device()
calls into i2c_get_adapter()/i2c_put_adapter() exported
interfaces. This is done to lock I2C bus device, if it is in use by a
client.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for VCT-jig parallel port I2C adapter to i2c-parport.
The adapter schematic can be found here (in the RAR file):
http://remont-aud.net/shop/22/desc/vct-jig-komplekt-dlja-samostojatelnoj-sborki
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra I2C controller required to configure the clock divisor
register inside controller to different value based on the clock
speed. The recommended clock divisor for the I2C controller for
standard/fast mode is 0x19 and for fast-mode plus is 0x10.
Add support to configure clock divisor register of I2C controller
based on bus clock rate.
This clock divisor is supported form T114 onwards.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Once the new configuration is set on the conifg register of
I2C controller, it is require to update the CONFIG_LOAD register
to transfer the new SW configuration to actual HW internal
registers that would be used in the actual logic.
It is like, SW is programming only shadow registers through
regular configuration and when these load_config bit fields
are set to 1, it causes the regular/shadows registers
configuration transferred to the HW internal active registers.
So SW has to set these bit fields at the end of all regular
registers configuration. And these config_load bits are HW
auto-clear bits. HW clears these bit fields once the register
configuration is moved to HW internal active registers. So SW
has to wait until these bits are auto-cleared before going
for any further programming
This mechanism is supported on T124 and after this SoCs.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patch "i2c: omap: abolish variable name confusion" triggered a
coccinelle warning which we fix here:
drivers/i2c/busses/i2c-omap.c:1333:5-24: pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at line 1334
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of error conditions like Arbitration lost or NACK lets signal
the waiting process.
Handle error cases in the Rx path
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently only one interrupt is serviced in the isr.
In case the multiple interrupts happen simultenously we service and ack
only one of them. Check for all the causes in the isr and service them.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently there is no slave mode support in the driver
also in the isr we just ack it and do nothing.
So disable the AAS interrupt.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the busy loop while waiting for bus busy.
Instead let the processor sleep.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the interrupts are disabled.
So incase the slave nacks in the middle of the transfer the
current transfer is not aborted. Upon enabling the interrupts
conditions like NACK , arbitration lost will not be masked.
Remove the disabling of the interrupts.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the controller is reinitialised.
We are already resetting the controller upon errors so upon every
transfer is a performance kill.
Remove the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The xiic_process is a 154 line code that runs in isr context currently
move it to thread context. Also the name xiic_process suggests that the
intension was to run in process context.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
[wsa: initialized irqreturn_t to IRQ_NONE instead of IRQ_HANDLED]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the interrupts are disabled at the start of the
isr and enabled at the end of the isr. Remove the same.
In case the slave device NACKs the transaction while in the isr
the transfer will continue and the NACK interrupt will arrive
only after the isr is serviced.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch cleans up i2c_pxa_probe() function,
- Use devm_ variants wherever
This will clean both probe exit and i2c_pxa_remove() functions
- Check platform resource before parsing any other data from DT/platform
- Use dev_err on failure from i2c_add_numbered_adapter()
- Use pr_info instead of printk for KERN_INFO
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: removed unneeded error prinout after devm_ioremap_resource]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update i2c_pxa_scream_blue_murder() fn to print more information
in case of error.
Also, use dev_err variants instead of printk.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix below warning message, coming from 64 bit toolchain.
drivers/i2c/busses/i2c-pxa.c:1237:15:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Yipeng Yao <ypyao@marvell.com>
[vaibhav.hiremath@linaro.org: Updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of timeout in pio mode of operation return I2C_RETRY.
This behavior will be same as interrupt mode of operation.
Signed-off-by: Shouming Wang <wangshm@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Normally i2c controller works as master, so slave addr is not needed, or
it will impact some slave device (eg. ST NFC chip) i2c accesses, because
it has the same i2c address with controller.
For example,
On the pxa1928 based platform, where PMIC (88pm860) is present @0x30
address on TWSI0 interface, and if we set 0x30 as a slave address in
pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During suspend there may still be some i2c access happening, as the
interrupt is shared between multiple drivers.
And if we don't keep i2c irq ON, there may be i2c access timeout if
i2c is in irq mode of operation.
Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
[vaibhav.hiremath@linaro.org: updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
we're about to remove the module, so we can't
really schedule a PM transition in the future,
we must wait for it to finish.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct device pointers are usually called
dev. Calling our struct omap_i2c_dev pointers
also dev has caused enough confusion.
This is the result of a few simple sed rules
to convert all struct omap_i2c_dev pointers
to be called omap instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
there's no need to fetch the platform_device
in order to dereference it back to the dev
pointer to access drvdata, we can use
dev_get_drvdata() instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Start using pr_fmt and convert all remaining printk to use
pr_* family of macros.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
[wsa: remove print on kzalloc failure]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now parport is using device model so use dev_* macros instead of printk.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If of_find_i2c_device_by_node() or of_find_i2c_adapter_by_node() find
a device by node, but its type does not match, a reference to that
device is still held. This change fixes the problem.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix some typos found in a printk message and
MODULE_DESCRIPTION.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to
allow direct access to the SCL and SDA pins. In addition to ST_EN, we
need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select).
Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive
low level"), we need to set them to 1 (which means "high-impedance") to
avoid unwanted changes on the pins.
As a precaution, reset all these bits to their default values after
recovery is complete.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using set_scl may be ineffective before calling the driver specific
prepare_recovery callback, which might change into a test mode. So
instead of setting SCL in i2c_generic_scl_recovery, move it to
i2c_generic_recovery (after the optional prepare_recovery).
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c
Note, on file size overflow read() now returns 0, and this is a
correct and expected EOF notification according to POSIX.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when using I2C and device
overlays containing a mux.
This patch is also more careful with the release of the adapter device
which caused a deadlock with muxes, and does not break the build
on !OF since the node flag accessors are not defined then.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Current code returns 0 if fails to read clock-frequency DT property,
fix it. Also add checking return value of clk_prepare_enable and
propagate return value of devm_request_irq.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
=H5wD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
- major updates to at91, davinci
- bugfixes to the mux infrastructure when dealing with the new quirk
mechanism
- more users for the bus recovery feature
- further improvements to the slave framework
Plus the usual bunch of smaller driver and core improvements and
fixes.
There is one patch removing old code from an ARM platform. This has
been acked by the sh_mobile maintainer Simon Horman"
* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
i2c: busses: i2c-bcm2835: limits cdiv to allowed values
i2c: sh_mobile: use proper type for timeout
i2c: sh_mobile: use adapter default for timeout
i2c: rcar: use proper type for timeout
i2c: rcar: use adapter default for timeout
i2c: designware: Make sure the device is suspended before disabling runtime PM
i2c: tegra: apply size limit quirk
i2c: tegra: don't advertise SMBUS_QUICK
i2c: octeon: remove unused signal handling
i2c: davinci: Optimize SCL generation
i2c: mux: pca954x: Use __i2c_transfer because of quirks
i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
i2c: use parent adapter quirks in mux
i2c: bcm2835: clear reserved bits in S-Register
ARM: shmobile: r8a7740: remove I2C errata handling
i2c: sh_mobile: add errata workaround
i2c: at91: fix code checker warnings
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
i2c: davinci: Avoid sending to own address
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
...
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ofUZ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Here are the changes for MMC for v4.2.
MMC core:
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation"
* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
mmc: queue: prevent soft lockups on PREEMPT=n
mmc: mediatek: Add PM support for MMC driver
mmc: mediatek: Add Mediatek MMC driver
mmc: dt-bindings: add Mediatek MMC bindings
mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
mmc: sdhci: fix low memory corruption
mmc: sdhci-pci: Change AMD SDHCI quirk application scope
i2c-piix4: Use Macro for AMD CZ SMBus device ID
pci_ids: Add AMD KERNCZ device ID support
mmc: queue: use swap() in mmc_queue_thread()
mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
mmc: sdhci: Restore behavior while creating OCR mask
mmc: sdhci-pxav3: fix device wakeup initialization
mmc: core: Attach PM domain prior probing of SDIO func driver
mmc: core: Remove redundant ->power_restore() callback for SD
mmc: core: Remove redundant ->power_restore() callback for MMC
mmc: sdhci-bcm2835: Actually enable the clock
mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
mmc: sdhci-of-esdhc: enable interrupt mode to detect card
mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
...
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
Checks if the cdiv value is in between min (0x2) and max (0xFFFE)
supported values by the bcm2835. If not, it returns -ENODEV.
See page 33/34 of BCM2835-ARM-Peripherals.pdf for the DIV register.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
[wsa: resolved a merge conflict]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver calls pm_runtime_put() right before pm_runtime_disable() in its
->remove() hook to make sure clock is gated etc. However, it turns out that
pm_runtime_put() only calls ->idle() hook without actually suspending
anything. The following pm_runtime_disable() will prevent the driver from
suspending thus leaving it "active".
It is better to suspend the device synchronously to make sure it is
actually suspended before disabling runtime PM from it.
While there, undo call to pm_runtime_use_autosuspend().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
payload_size is a 12 bit field in the HW register, so add a limit for
this size. That way we gracefully reject the message beforehand instead
of generating an OOPS while transferring. Verified using some older
Tegra2 documentation and a more recent Jetson TK1 board.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
This HW cannot send 0-byte-length messages and the driver discards them.
So, we should not advertise SMBUS_QUICK.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'commit 2637e5fd23 ("i2c: octeon: Fix i2c fail problem when a process is
terminated by a signal")' removed the wait_event_interruptible_timeout to
prevent half/mixed i2c messages from being sent/recievd but forgot to
drop the signal handling case in the return handling. This just removes
this dead code. While at it the return variable is adjusted to the type
expected.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several cases where current clock configuration algorithm produces
not optimal results:
- truncation in "clk" calculation leads to the fact that actual BUS frequency
will be always higher than spec except two exact module frequences 8MHz and
12MHz in the whole 7-12MHz range of permitted frequences
- driver configures SCL HIGH to LOW ratio always 1 to 1 and this doesn't work
well in 400kHz case, namely minimum time of LOW state (according to I2C Spec
2.1) 1.3us will not be fulfilled. HIGH to LOW ratio 1 to 2 would be more
approriate here.
Signed-off-by: Michael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pca9541 and pca954x are calling master_xfer() of the parent adapter directly
thus bypassing the quirks checks of the adapter. Use __i2c_transfer() instead.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
Newly introduced quirks infrastructure doesn't work for the devices behind
MUXes because MUX's master_xfer() calls parent's master_xfer() directly
without checking the quirks. Instead of duplicating check code in MUX just
call __i2c_transfer() instead. This has a side effect on tracing (messages
will appear on both MUX bus and parent bus), but maybe that's not bad at
the end.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
Inherit parent adapter quirks in MUX in case the devices on the multiplexed
buses are interested in the adapter limitations.
Signed-off-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
The datasheet mentions on page 31 that the bits 10-31 must be read as
don't care and written as 0.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
We cannot guarantee that we read bits 10-31 as always 0 (because the
datasheet says read as don't care). We clear the bits with a bitmask to
prevent writing back unknown data at the reserved bits.
Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This used to be in platform init code. We want it to do in the driver
now. This is basically a code move and a new compatible added.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Change AMD CZ SMBUS device ID from 0x790b to
use Macro definition
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
buf_len is a size_t, so unsigned, but was tested with '<= 0'.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix section mismatch error during kernel build for xgene_slimpro_i2c_probe
function. It was incorrectly defined with __init declaration.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sending a message to own address locks the controller up in very bizarre state,
it behaves as slave even if MDR register clearly states master. The controller
remains in this state until reset. To avoid unnecessary timeouts simply avoid
sending to own address. The controller cannot do this any way. Also, do not
enable AAS IRQ, as the slave mode is not supported by the driver and the only
possibility to trigger this IRQ is to send to own address.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several problems in the function:
- "to_cnt" variable does nothing
- schedule_timeout() call without setting current state does nothing
- "allow_sleep" parameter is not really used
Refactor the function so that it really tries to wait. In case of timeout try
to recover the bus.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When FIFOs are available and enabled, the driver now configures the Atmel
eXtended DMA Controller to perform word accesses instead of byte accesses
when possible.
The actual access width depends on the size of the buffer to transmit.
To enable FIFO support the "atmel,fifo-size" property must be set properly
in the I2C controller node of the device tree.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe() function now prints the hardware version of the I2C
controller.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[wsa: s/version/hw version/] for clarity]
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The alternative command mode was introduced to simplify the transmission
of STOP conditions and to solve timing and latency issues around them.
This mode relies on a new register, the Alternative Command Register,
which must be set at the same time as the Master Mode Register. This new
register was designed to allow simple setup of basic combined transactions
built from up to two unitary transactions.
Indeed, the ACR is split into two areas, which describe one unitary
transaction each. Each area is filled with Data Length 8bit counter, a
Direction and a PEC Request bit. The PEC bit is only used in SMBus mode
and is not supported by this driver yet. Also when using alternative
command mode, the MREAD bit from the Master Mode Register is ignored.
Instead the Direction bits from ACR are used to setup the direction, read
or write, of each unitary transaction. Finally the 8bit counters must
filled with the data length of their respective transaction. Then if only
one transaction is to be used, the data length of the second one must be
set to zero. At the moment, this driver uses only the first transaction.
In addition to MMR and ACR, the Control Register also need to be written
to enable the alternative command mode. That's the purpose of its ACMEN
bit, which stands for Alternative Command Mode Enable.
Note that the alternative command mode is compatible with the use of the
Internal Address Register. So combined transactions for eeprom read are
actually implemented with the Internal Address Register. This register is
written with up to 3 bytes, which are the internal address sent to the
slave through the first write transaction. Then the first area of the ACR
describe the write transaction to follow, which carries the data to be
read from the eeprom. The second area of the ACR is not used so its Data
Length 8bit counter is cleared.
For each byte sent or received by the device, the Data Length 8bit counter
is decremented. When it reaches 0, a STOP condition is automatically sent.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch just fixes typo before applying later patches which will use
register bits with index above 16.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For TX transactions, the TXCOMP bit in the Status Register is cleared
when the first data is written into the Transmit Holding Register.
In the lines from at91_do_twi_transfer():
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
the TXCOMP interrupt may be enabled before the DMA controller has
actually started to write into the THR. In such a case, the TXCOMP bit
is still set into the Status Register so the interrupt is triggered
immediately. The driver understands that a transaction completion has
occurred but this transaction hasn't started yet. Hence the TXCOMP
interrupt is no longer enabled by at91_do_twi_transfer() but instead
by at91_twi_write_data_dma_callback().
Also, the TXCOMP bit in the Status Register in not a clear on read flag
but a snapshot of the transmission state at the time the Status
Register is read.
When a NACK error is dectected by the I2C controller, the TXCOMP, NACK
and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP
interrupt is triggered at the same time. Also setting the TXRDY to 1
triggers the DMA controller to write the next data into the THR. Such
a write resets the TXCOMP bit to 0 in the SR. So depending on when the
interrupt handler reads the SR, it may fail to detect the NACK error
if it relies on the TXCOMP bit. The NACK bit and its interrupt should
be used instead.
For RX transactions, the TXCOMP bit in the Status Register is cleared
when the START bit is set into the Control Register. However to unify
the management of the TXCOMP bit when the DMA controller is used, the
TXCOMP interrupt is now enabled by the DMA callbacks for both TX and
RX transfers.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cc: stable@vger.kernel.org #3.10 and later
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add suspend/resume support to the Broadcom iProc I2C driver
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 1fc2fe204c ("i2c: designware: Add runtime PM hooks") adds
runtime pm support using the same ops for system pm and runtime pm.
When suspend to ram, the i2c host may have been runtime suspended, thus
i2c_dw_disable() hangs.
Previously, I fixed this issue by separating ops for system pm and
runtime pm, then in the system suspend/resume path, runtime pm apis are
used to ensure the device is at correct state.
But as Mika Westerberg pointed out: it sounds a bit silly to resume the
device just because you want to call i2c_dw_disable() for it before
suspending again. He then suggested an elegant solution which keeps the
device runtime suspended during system suspend with the help of
'dev->power.direct_complete'. This patch adopted this solution, and in
fact Mika provided the main code.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use recovery framework and implement bus recovery using "Bus Monitor" register.
Tests show that shortening SDA to GND results in "completion" timeout with
"BUSY" bit still set, so initiate recovery in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sizeof(struct i2c_client) is 1088 bytes on a CONFIG_X86_64=y build and
produces following warning when CONFIG_FRAME_WARN is set to 1024:
drivers/i2c/i2c-core.c: In function ‘acpi_i2c_space_handler’:
drivers/i2c/i2c-core.c:367:1: warning: the frame size of 1152 bytes is
larger than 1024 bytes [-Wframe-larger-than=]
This is not critical given that kernel stack is 16 kB on x86_64 but lets
reduce the stack usage by allocating the struct i2c_client from the heap.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
int is vague, let's simply use the type of the variable in question.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inform users what went wrong from the core, so drivers don't have to do
it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Modify i2c-parport driver to use the new parallel port device model.
Tested-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of now i2c-parport was connecting to all the available parallel
ports. Lets limit that to maximum of 4 instances and at the same time
define which instance connects to which parallel port.
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following what DT already does. If the device does not have ACPI Interrupt
resource but instead it has one or more GpioInt resources listed below it,
we take the first GpioInt resource, convert it to suitable Linux IRQ number
and pass it to the driver instead.
This makes drivers simpler because the don't need to care about GPIOs at
all if only thing they need is interrupt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the convention used in most parts of the kernel including DT
counterpart of I2C slave enumeration. To make things consistent do the same
for ACPI I2C slave enumeration path as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
implement bus recovery methods for i2c-omap
so we can recover from situations where SCL/SDA
are stuck low.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The platform_device_id is not modified by these drivers and core uses it
as const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Initialize sysreg by default, otherwise driver will crash in suspend
callback when not using DT.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: a7750c3ef0 ("i2c: s3c2410: Handle i2c sys_cfg register in i2c driver")
Make the modalias match driver name, this is required to make module
auto-loading work.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in the DT, these calls turn
to NOPs, so we don't need error checking here.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
info(drivers/i2c/busses/i2c-xiic.c:55): Scanning doc for struct xiic_i2c
Warning(drivers/i2c/busses/i2c-xiic.c:79): No description found for parameter 'endianness'
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely, it is remotely possible for an i2c command to need
more than 200ms complete. Unlike smbus, i2c devices can clock stretch
for an unspecified amount of time. The longest time I've seen
specified for a device is 144ms (bq27541 battery gas), but one could
imagine a device taking a bit slower. 1 second "ought to be enough for
anyone."
The above is not the only justifcation for going above 200ms for a
timeout, though. It turns out that if you've got a large number of
printks going out to a serial console, interrupts on a CPU can be
disabled for hundreds of milliseconds. That's not a great situation to
be in to start with (maybe we should put a cap in vprintk_emit()) but
it's pretty annoying to start seeing unexplained i2c timeouts.
Note that to understand why we can timeout when printk has interrupts
disabled, you need to understand that on current Linux ARM kernels
interrupts are routed to a single CPU in a multicore system. Thus,
you can get:
1. CPU1 is running rk3x_i2c_xfer()
2. CPU0 calls vprintk_emit(), which disables all IRQs on CPU0.
3. I2C interrupt is ready but is set to only run on CPU0, where IRQs
are disabled.
4. CPU1 timeout expires. I2C interrupt is still ready, but CPU0 is
still sitting in the same vprintk_emit()
5. CPU1 sees that no interrupt happened in 200ms, so timeout.
A normal system shouldn't see i2c timeouts anyway, so increasing the
timeout should help people debugging without hurting other people
excessively.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"This has a mixture of merge window cleanups and bugfixes"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: st: add include for pinctrl
i2c: mux: use proper dev when removing "channel-X" symlinks
i2c: digicolor: remove duplicate include
i2c: Mark adapter devices with pm_runtime_no_callbacks
i2c: pca-platform: fix broken email address
i2c: mxs: fix broken email address
i2c: rk3x: report number of messages transmitted
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
The driver uses pinctrl directly and thus should include the appropriate
header. Sort the headers while we are here to have a better view what is
included and what is not.
Reported-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Those symlinks are created for the mux_dev, so we need to remove it from
there. Currently, it breaks for muxes where the mux_dev is not the device
of the parent adapter like this:
[ 78.234644] WARNING: CPU: 0 PID: 365 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x5c/0x78()
[ 78.242438] sysfs: cannot create duplicate filename '/devices/platform/i2cbus@8/channel-0'
Remove confusing comments while we are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: c9449affad
Cc: stable@kernel.org
And sort them to prevent this from happening again.
Reported-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 523c5b8964 ("i2c: Remove support for legacy PM") removed the PM
ops from the bus type, which causes the pm operations on the s3c2410
adapter device to fail (-ENOSUPP in rpm_callback). The adapter device
doesn't get bound to a driver and as such can't have its own pm_runtime
callbacks. Previously this was fine as the bus callbacks would have been
used, but now this can cause devices which use PM runtime and are
attached over I2C to fail to resume.
This commit fixes this issue by marking all adapter devices with
pm_runtime_no_callbacks, since they can't have any.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Beata Michalska <b.michalska@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 523c5b8964
Cc: stable@kernel.org
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
master_xfer() method should return number of i2c messages transferred,
but on Rockchip we were usually returning just 1, which caused trouble
with users that actually check number of transferred messages vs.
checking for negative error codes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Current -next fails to link an ARM allmodconfig because drivers that use
the core recovery functions can be built as modules but those functions
are not exported:
ERROR: "i2c_generic_gpio_recovery" [drivers/i2c/busses/i2c-davinci.ko] undefined!
ERROR: "i2c_generic_scl_recovery" [drivers/i2c/busses/i2c-davinci.ko] undefined!
ERROR: "i2c_recover_bus" [drivers/i2c/busses/i2c-davinci.ko] undefined!
Add exports to fix this.
Fixes: 5f9296ba21 (i2c: Add bus recovery infrastructure)
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix:
drivers/i2c/busses/i2c-jz4780.c: In function 'jz4780_i2c_readw':
drivers/i2c/busses/i2c-jz4780.c:181:2: error:
implicit declaration of function 'readw'
drivers/i2c/busses/i2c-jz4780.c: In function 'jz4780_i2c_writew':
drivers/i2c/busses/i2c-jz4780.c:187:2: error:
implicit declaration of function 'writew'
seen with sparc64:allmodconfig and m68k:allmodconfig.
The driver has to include linux/io.h.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver
for Ingenic JZ4780")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJVLbO+AAoJEILEb/54YlRx5N4QAJXsmEW1FL2l6mMAyTQkEsVj
nbqjF9I6aJgYM9+i8GKaZJxpN17SAZ7Ii7aCAXjPwX8AvjT70+gcZr+KDWtPir61
B75VNVEcUYOR4vOF5Z6rQcQMlhGPkfMOJYXFMahpOG6DdPbVh1x2/tuawfc6IC0V
a6S/fln6WqHrXQ+8swDSv1KuZsav6+8AQaTlNUQkkuXdY9b3k/3xiy5C2K26APP8
x1B39iAF810qX6ipnK0gEOC3Vs29dl7hvNmgOVmmkBGVS7+pqTuy5n1/9M12cDRz
78IQ7DXB0NcSwr5tdrmGVUyH0Q6H9lnD3vO7MJkYwKDh5a/2MiBr2GZc4KHDKDWn
E1sS27f1Pdn9qnpWLzTcY+yYNV3EEyre56L2fc+sh+Xq9sNOjUah+Y/eAej/IxYD
XYRf+GAj768yCJgNP+Y3PJES/PRh+0IZ/dn5k0Qq2iYvc8mcObyG6zdQIvCucv/i
70uV1Z2GWEb31cI9TUV8o5GrMW3D0KI9EsCEEpiFFUnhjNog3AWcerGgFQMHxu7X
ZnNSzudvek+XJ3NtpbPgTiJAmnMz8bDvBQm3G1LUO2TQdjYTU6YMUHsfzXs8DL6c
aIMWO4stkVuDtWrlT/hfzIXepliccyXmSP6sbH+zNNCepulXe5C4M2SftaDi4l/B
uIctXWznvHoGys+EFL+v
=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
Pull i2c updates from Wolfram Sang:
"Most notable:
- introducing the i2c_quirk infrastructure. Now, flaws of I2C
controllers can be described and the core will check if the flaws
collide with the messages to be sent
- wait_for_completion return type cleanup series
- new drivers for Digicolor, Netlogic XLP, Ingenic JZ4780
- updates to the I2C slave framework which include API changes. Its
only user was updated, too. Documentation was finally added
- changed dynamic bus numbering for the DT case. This could change
bus numbers for users. However, it fixes a collision where dynamic
and static busses request the same id.
- driver bugfixes, cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
of: Add vendor prefix 'netlogic'
i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery
i2c: davinci: use bus recovery infrastructure
i2c: change input parameter to i2c_adapter for prepare/unprepare_recovery
i2c: i2c-mux-gpio: remove error messages for probe deferrals
i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780
i2c: dln2: set the device tree node of the adapter
i2c: davinci: fixup wait_for_completion_timeout handling
i2c: mpc: Fix ISR return value
i2c: slave-eeprom: add more info when to increase the pointer
i2c: slave: add documentation for i2c-slave-eeprom
Documentation: i2c: describe the new slave mode
i2c: slave: rework the slave API
i2c: add support for the Digicolor I2C controller
i2c: busses with dynamic ids should start after fixed ids for DT
of: base: add function to get highest id of an alias stem
i2c: designware: Suppress error message if platform_get_irq() < 0
i2c: mpc: assign the correct prescaler from SVR
i2c: img-scb: fixup of wait_for_completion_timeout return handling
...
Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Having a board where the I2C bus locks up occasionally made it clear
that the bus recovery in the i2c-davinci driver will only work on
some boards, because on regular boards, this will only toggle GPIO
lines that aren't muxed to the actual pins.
The I2C controller on SoCs like da850 (and da830), Keystone 2 has the
built-in capability to bit-bang its lines by using the ICPFUNC registers
of the i2c controller.
Implement the suggested procedure by toggling SCL and checking SDA using
the ICPFUNC registers of the I2C controller when present. Allow platforms
to indicate the presence of the ICPFUNC registers with a has_pfunc platform
data flag and add optional DT property "ti,has-pfunc" to indicate
the same in DT.
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Michael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Mike Looijmans <milo-software@users.sourceforge.net>
[grygorii.strashko@ti.com: combined patches from Ben Gardiner and
Mike Looijmans and reimplemented ICPFUNC bus recovery using I2C
bus recovery infrastructure]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch converts Davinci I2C driver to use I2C bus recovery
infrastructure, introduced by commit 5f9296ba21 ("i2c: Add
bus recovery infrastructure").
The i2c_bus_recovery_info is configured for Davinci I2C adapter
only in case scl_pin is provided in platform data.
As the controller must be held in reset while doing so, the
recovery routine must re-init the controller. Since this was already
being done after each call to i2c_recover_bus, move those calls into
the recovery_prepare/unprepare routines and as well.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes type of input parameter for
prepare/unprepare_recovery() callbacks from struct i2c_bus_recovery_info
* to struct i2c_adapter *. This allows to simplify implementation of
these callbacks and avoid type conversations from i2c_bus_recovery_info
to i2c_adapter. The i2c_bus_recovery_info can be simply retrieved from
struct i2c_adapter which contains pointer on it. There are no users
currently, so this is safe to do.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe deferral is not an error case. It happens only when
the necessary dependencies are not there yet.
The driver core is already printing a message when a driver
requests probe deferral, so this can be traced in the logs
without these error prints.
This patch removes the error messages for these deferral cases.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nokia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds the i2c bus controller driver for the Ingenic JZ4780 SoC.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch makes sure the platform device tree node is inherited by
the adapter device. This allows the DLN2 bus to work with i2c devices
defined in the device tree.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
wait_for_completion_timeout return 0 (timeout) or >=1 (completion) so the check
for >= 0 is always true and can be dropped implying that r==-EREMOTEIO and thus
the return of -EREMOTEIO can be done in the if (dev->buf_len) branch.
As wait_for_completion_timeout returns unsigned long not int, and int r is
exclusively used for wait_for_completion_timeout it is renamed and the type
changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ISR should not return IRQ_HANDLED for not handling anything.
This patch fixes the return value of ISR for the same case.
Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Acked-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is a bit subtle when to correctly increase the buffer index when
reading. Make this clearer by adding some more comments and pointers to
the docs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After more discussion, brave users, and additional datasheet evaluation,
some API updates for the new I2C slave framework became imminent. The
slave events now get some easier to understand naming. Also, the event
handling has been simplified to only need a single call to the slave
callback when an action by the backend is required.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The CX92755 is an SoC in the Conexant Digicolor series. The devicetree binding
document describes the I2C controller on the CX92755 SoC, that is also shared
by some other SoCs in the Digicolor series. The driver adds support.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[wsa: fixed spaces around operators]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure dynamic ids do not interfere with fixed ones and let them
start after the highest fixed id. This patch might cause different
bus-numbers than before for dynamic ids, however it fixes a bug. Assume:
- fixed id0 defers probe
- fixed id1 succeeds and registers a muxed bus with dynamic id
- muxed bus gets id0
- fixed id0 wants to probe again, but its fixed id is gone now
- fixed id0 probe fails
With this patch, the fixed ids are always reserved in the DT case.
For legacy board init, we already have a mechanism like this in
i2c_register_board_info().
Reported-by: Bob Feretich <bob.feretich@rafresearch.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that the ACPI companions of devices are represented by pointers
to struct fwnode_handle, it is not quite efficient to check whether
or not an ACPI companion of a device is present by evaluating the
ACPI_COMPANION() macro.
For this reason, introduce a special static inline routine for that,
has_acpi_companion(), and update the code to use it where applicable.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have struct fwnode_handle, we can use that to point to
ACPI companions from struct device objects instead of pointing to
struct acpi_device directly.
There are two benefits from that. First, the somewhat ugly and
hackish struct acpi_dev_node can be dropped and, second, the same
struct fwnode_handle pointer can be used in the future to point
to other (non-ACPI) firmware device node types.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
With -EPROBE_DEFER, this message is confusing and we hope for a
centralized printout in the future anyhow.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For the 85xx platforms, the source clock for the i2c-mpc can change from
one SoC to another. This is documented in the AN2919 "Determining the
I2C Frequency Divider Ratio for SCL" by Freescale. Not taking this into
account can lead to the output SCL frequency to by off by an offset. It
was observed on the P2041 from the QorIQ family.
This patch fixes this problem by setting the prescaler value to the
appropriate value when required. The SoCs that required a different
prescaler than 1 are identified by reading out the SVR as discussed in
http://thread.gmane.org/gmane.linux.drivers.devicetree/94247/focus=20556
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Return type of wait_for_completion_timeout is unsigned long not int.
Appropriately typed/named variable are added and assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Return type of wait_for_completion_timeout is unsigned long not int. This
patch adds a timeout variable of appropriate type and fixes up the assignment.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of read_i2c() is int not u32. As the assignments to status
are consistent with int here its type is changed to int.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. as
timeout is used for wait_for_completion_timeout exclusively here its
type is simply changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int.
An appropriate variable of type unsigned long is introduced and the
assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. As
ret is in used for other calls a new appropriately typed variable timeout
is added to handle wait_for_completion_timeout
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. as
wait_result is only used for wait_for_completion_timeout here the type
is simply changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. as
time_left is used for wait_for_completion_timeout exclusively here its
type is simply changed to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int, rather
than introducing a new variable the wait_for_completion_timeout is moved
into the if condition as the return value is only used to detect timeout.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to make the timeout condition clearly readable
and the type adjusted to unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
return type of wait_for_completion_timeout is unsigned long not int. As ret
was only used for wait_for_completion_timeout here it is renamed to time_left
the type changed to unsigned long and references fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Let the core do the checks if HW quirks prevent a transfer. Saves code
from drivers and adds consistency.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Ray Jui <rjui@broadcom.com>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Tested-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Tested-By: Ludovic Desroches <ludovic.desroches@atmel.com>
This reverts commit e4df3a0b62
("i2c: core: Dispose OF IRQ mapping at client removal time")
Calling irq_dispose_mapping() will destroy the mapping and disassociate
the IRQ from the IRQ chip to which it belongs. Keeping it is OK, because
existent mappings are reused properly.
Also, this commit breaks drivers using devm* for IRQ management on
OF-based systems because devm* cleanup happens in device code, after
bus's remove() method returns.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wsa: updated the commit message with findings fromt the other bug report]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: e4df3a0b62
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.
Also there is an *_optional variant that serves well here. The sematics
is slightly changed here by using it. Now if a reset gpio is specified
and getting hold on it fails, pca954x_probe fails, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Simplifies the code a bit and makes easier to disable PCI device on driver
detach by removing the pcim_pin_device() call in the future if needed.
Reason why i2c-i801.c doesn't ever call pci_disable_device() was because it
made some systems to hang during power-off. See commit d6fcb3b9cf
("[PATCH] i2c-i801.c: don't pci_disable_device() after it was just enabled")
and
http://marc.info/?l=linux-kernel&m=115160053309535&w=2
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since pci_disable_device() is not called from i801_suspend() and power
state is set already it means that subsequent pci_enable_device() calls do
practically nothing but monotonically increase struct pci_dev enable_cnt.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This simplifies the error and remove paths.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct pci_driver i801_driver forward declaration is needed only for
accessing the name field. Remove it and use dev_driver_string() instead.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It makes more difficult to grep these error prints from sources if they are
split to multiple source lines.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages
while-loop to do-while and, though it is matter of taste, gives a chance to
check one more time before report a timeout.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems the idea behind the cross-check is to prevent acquire semaphore when
there is no release callback and vice versa. Thus, patch fixes a typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to export functions that are used as the callbacks in the
struct dw_i2c_dev. Otherwise we get the following warnings:
drivers/i2c/busses/i2c-designware-baytrail.c:63:5: warning: symbol 'baytrail_i2c_acquire' was not declared. Should it be static?
drivers/i2c/busses/i2c-designware-baytrail.c:114:6: warning: symbol 'baytrail_i2c_release' was not declared. Should it be static?
While here, do few indentation fixes, remove i2c_dw_eval_lock_support() from
functions exported to the modules and redundant assignment of local sem
variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It seems we have same message for different return values in get_sem() and
baytrail_i2c_acquire(). I suspect this is just a typo, so this patch fixes it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The patch converts hardcoded numerical constants to a named ones.
While here, align the variable name in get_sem() and reset_semaphore().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The struct cros_ec_command will be used as an ioctl() argument for the
API to control the ChromeOS EC from user-space. So the data structure
has to be 64-bit safe to make it compatible between 32 and 64 avoiding
the need for a compat ioctl interface. Since pointers are self-aligned
to different byte boundaries, use fixed size arrays instead of pointers
for transferring ingoing and outgoing data with the Embedded Controller.
Also, re-arrange struct members by decreasing alignment requirements to
reduce the needing padding size.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
For, !HAVE_CLK the clk API returns a NULL cookie. Rework the
initialization code to handle that. If clk_get_rate() delivers 0, we use
the fallback mechanisms. The patch is pretty easy when ignoring white
space issues (git diff -b).
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
IOSF_MBI is tristate. Baytrail driver isn't.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.
The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While here, fix few indentations issues across the code. There is no functional
change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow bus clock specification as a common clock handle. This makes this
controller easier to use in a setup based on common clock framework.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 9439eb3ab9 ("asm-generic: io: implement relaxed
accessor macros as conditional wrappers") has added
{read,write}{b,w,l,q}_relaxed to include/asm-generic/io.h.
So COMPILE_TEST can be added.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There was quite some confusion why this completion is there and if it is
still necessary. Sadly, it is. However, let's improve the comments and
share what we rediscovered.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clock-frequency property is meant to control the bus frequency for i2c bus
drivers, but it was incorrectly used to specify i2c controller input clock
frequency.
Introduce new attribute, opencores,ip-clock-frequency, that specifies i2c
controller clock frequency and make clock-frequency attribute compatible
with other i2c drivers. Maintain backwards compatibility in case
opencores,ip-clock-frequency attribute is missing.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA read requests could miss proper termination, so two more bytes would
have been read via PIO overwriting the end of the buffer with wrong
data. Make DMA stop handling more readable while we are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the slave support depend on CONFIG_I2C_SLAVE. Otherwise it gets
included unconditionally, even when it is not needed.
I2C bus drivers which implement slave support must select
I2C_SLAVE.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support CPU BE mode by adding endianness conversion for memcpy interactions.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IOSF_MBI depends on PCI, so we should not select it but depend on it.
This ensures also we compile on X86 only, other archs will break because
of an arch specific include. Also depend on ACPI since this driver uses
it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Do SCL timing parameter calculation conditionally depending are custom
parameters provided since calculated values will get instantly overwritten
by provided parameters.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trying to register an I2C device asynchronously (via async_schedule() call)
results in an ugly warning from request_module() warning about potential
deadlock (because request_module tries to wait for async works to
complete). While we could try to switch to request_module_nowait(), other
buses, as well as I2C itself when not using device tree, do not try to load
modules, but rather rely on the standard infrastructure (udev) to execute
module loading, and we should be doing the same.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch implements an I2C bus sharing mechanism between the host and platform
hardware on select Intel BayTrail SoC platforms using the X-Powers AXP288 PMIC.
On these platforms access to the PMIC must be shared with platform hardware. The
hardware unit assumes full control of the I2C bus and the host must request
access through a special semaphore. Hardware control of the bus also makes it
necessary to disable runtime pm to avoid interfering with hardware transactions.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds support for acquiring and releasing a hardware bus lock in the i2c
designware core transfer function. This is needed for i2c bus controllers
that are shared with but not controlled by the kernel.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch solves deadlock between clock prepare mutex and regmap mutex reported
by Tomasz Figa in [1] by implementing solution from [2]: "always leave the clock
of the i2c controller in a prepared state".
[1] https://lkml.org/lkml/2014/7/2/171
[2] https://lkml.org/lkml/2014/7/2/207
On each i2c transfer handled by s3c24xx_i2c_xfer(), clk_prepare_enable() was
called, which calls clk_prepare() then clk_enable(). clk_prepare() takes
prepare_lock mutex before proceeding. Note that i2c transfer functions are
invoked from many places in kernel, typically with some other additional lock
held.
It may happen that function on CPU1 (e.g. regmap_update_bits()) has taken a
mutex (i.e. regmap lock mutex) then it attempts i2c communication in order to
proceed (so it needs to obtain clock related prepare_lock mutex during transfer
preparation stage due to clk_prepare() call). At the same time other task on
CPU0 wants to operate on clock (e.g. to (un)prepare clock for some other reason)
so it has taken prepare_lock mutex.
CPU0: CPU1:
clk_disable_unused() regulator_disable()
clk_prepare_lock() map->lock(map->lock_arg)
regmap_read() s3c24xx_i2c_xfer()
map->lock(map->lock_arg) clk_prepare_lock()
Implemented solution from [2] leaves i2c clock prepared. Preparation is done in
s3c24xx_i2c_probe() function. Without this patch, it is immediately unprepared
by clk_disable_unprepare() call. I've replaced this call with clk_disable() and
I've added clk_unprepare() call in s3c24xx_i2c_remove().
The s3c24xx_i2c_xfer() function now uses clk_enable() instead of
clk_prepare_enable() (and clk_disable() instead of clk_unprepare_disable()).
Signed-off-by: Paul Osmialowski <p.osmialowsk@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Due to a copy&paste error, the last byte of the shared memory was not
accessible via sysfs.
Reported-by: Debora Grosse <debora@mds.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c-mux-idle-disconnect device tree property to PCA954x mux driver. The new
property forces the multiplexer to disconnect child buses in idle state. This is
used, for example, when there are several multiplexers on the same bus and the
devices on the underlying buses might have same I2C addresses.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[wsa: added a newline]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
readl/writel is too expensive especially on Cortex A9 w/ outer L2 cache.
This introduces i2c read/write delays on Marvell BG2/BG2Q SoCs when there
are heavy L2 cache maintenance operations at the same time.
The driver does not perform DMA, so it's safe to use the relaxed version.
From another side, the relaxed io accessor macros are available on all
architectures now, so we can use the relaxed versions instead.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The clk_khz field makes sense only if SS counters are not provided. Since we
provide them for Haswell and Baytrail explicitly we may omit the clk_khz
parameter.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Moorestown support bits were removed few years ago. This is a follow up to
that changes.
Suggested-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes up some whitespace issues and addresses a few
checkpatch warnings.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Declaring attribute groups can be done with macros these days, let's use
them for consistency and readability reasons. Also, put the ATTR macros
directly below the referenced functions while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ret variable is set and never used in the error path of i2c_imx_dma_request.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI specification allows I2C devices with multiple addresses. The current
implementation goes over all addresses and assigns the last one to the
device. This is typically not the primary address of the device.
Instead of doing that we assign the first address to the device and then
let the driver handle rest of the addresses as it wishes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence I2C controller has the following bugs:
- completion indication is not given to the driver at the end of
a read/receive transfer with HOLD bit set.
- Invalid read transaction are generated on the bus when HW timeout
condition occurs with HOLD bit set.
As a result of the above, if a set of messages to be transferred with
repeated start includes any message following a read message,
completion is never indicated and timeout occurs.
Hence a check is implemented to return -EOPNOTSUPP for such sequences.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
[wsa: fixed some whitespaces]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
wait_for_completion_timeout does not return negative values so
"result" handling here should be simplified to cover the actually
possible cases only.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Rockchip I2C the controller drops SDA low slightly too soon to meet
the "repeated start" requirements.
>From my own experimentation over a number of rates:
- controller appears to drop SDA at .875x (7/8) programmed clk high.
- controller appears to keep SCL high for 2x programmed clk high.
The first rule isn't enough to meet tSU;STA requirements in
Standard-mode on the system I tested on. The second rule is probably
enough to meet tHD;STA requirements in nearly all cases (especially
after accounting for the first), but it doesn't hurt to account for it
anyway just in case.
Even though the repeated start requirement only need to be accounted
for during a small part of the transfer, we'll adjust the timings for
the whole transfer to meet it. I believe that adjusting the timings
in just the right place to switch things up for repeated start would
require several extra interrupts and that doesn't seem terribly worth
it.
With this change and worst case rise/fall times, I see 100kHz i2c
going to ~85kHz. With slightly optimized rise/fall (800ns / 50ns) I
see i2c going to ~89kHz. Fast-mode isn't affected much because
tSU;STA is shorter relative to tHD;STA there.
As part of this change we needed to account for the SDA falling time.
The specification indicates that this should be the same, but we'll
follow Designware's lead and add a binding. Note that we deviate from
Designware and assign the default SDA falling time to be the same as
the SCL falling time, which is incredibly likely.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: rebased to i2c/for-next]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The number of clock cycles to be written into the CLKDIV register
that determines the I2C clk high phase includes the rise time.
So to meet the timing requirements defined in the I2C specification
which defines the minimal time SCL has to be high, the rise time
has to taken into account. The same applies to the low phase with
falling time.
In my test on RK3288-Pink2 board, which is not an upstream board yet,
if external pull-up resistor is 4.7K, rise_ns is about 700ns.
So the measured high_ns is about 3900ns, which is less than 4000ns
(the minimum high_ns in I2C specification for Standard-mode).
To fix this bug min_low_ns should include fall time and min_high_ns
should include rise time.
This patch merged the patch from chromium project which can get the
rise and fall times for signals from the device tree. This allows us
to more accurately calculate timings. see:
https://chromium-review.googlesource.com/#/c/232774/
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
[wsa: fixed a typo in the docs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C controller sends a NACK to the slave when transfer size register
reaches zero, irrespective of the hold bit. So, in order to handle transfers
greater than 252 bytes, the transfer size register has to be maintained at a
value >= 1. This patch implements the same.
The interrupt status is cleared at the beginning of the isr instead of
the end, to avoid missing any interrupts.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
[wsa: added braces around else branch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CPPCHECK rightfully says:
drivers/i2c/busses/i2c-pmcmsp.c:151: style: The function 'pmcmsptwi_reg_to_clock' is never used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
There haven't been any I2C driver that use the legacy suspend/resume
callbacks for a while now and new drivers are supposed to use PM ops. So
remove support for legacy suspend/resume for I2C drivers.
Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback directly to
using the device's PM ops if no bus PM ops are specified there is no need to
have any I2C bus PM ops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
The highlight is the series that reworks the idle management on powernv, which
allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!" problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he asked that we
take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of the audit
maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a sysfs file,
so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for smt-enabled, and
the patch to add __force to get_user() so we can use bitwise types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GXdK
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
If NO_DMA=y:
drivers/built-in.o: In function `sh_mobile_i2c_dma_unmap':
i2c-sh_mobile.c:(.text+0x60de42): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_mobile_i2c_xfer_dma':
i2c-sh_mobile.c:(.text+0x60df22): undefined reference to `dma_map_single'
i2c-sh_mobile.c:(.text+0x60df2e): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA is opt-in for this driver. So, we can't use deferred probing for
requesting DMA channels in probe, because our driver would get endlessly
deferred if DMA support is compiled in AND the DMA driver is missing.
Because we can't know when the DMA driver might show up, we always try
again when a DMA transfer would be possible. The downside is that there
is more overhead for setting up PIO transfers under the above scenario.
But well, having DMA enabled and the proper DMA driver missing looks
like a broken or test config anyhow.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Refactor DMA setup to keep the errno so we can implement better
deferred probe support in the next step.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Originally, the I2C controller supported by the i2c-mv64xxx driver
requires a lot of software support: an interrupt is generated at each
step of an I2C transaction (after the start bit, after sending the
address, etc.) and the driver is in charge of re-programming the I2C
controller to do the next step of the I2C transaction. This explains
the fairly complex state machine that the driver has.
On Marvell Armada XP and later processors (Armada 375, 38x, etc.), the
I2C controller was extended with a part called the "I2C Bridge", which
allows to offload the I2C transaction completely to the
hardware. Initial support for this mechanism was added in commit
930ab3d403 ("i2c: mv64xxx: Add I2C Transaction Generator support").
However, the implementation done in this commit has two related
issues, which this commit fixes by completely changing how the offload
implementation is done:
* SMBus read transfers, where there is one write to select the
register immediately followed in the same transaction by one read,
were making the processor hang. This was easier visible on the
Marvell Armada XP WRT1900AC platform using a driver for an I2C LED
controller, or on other Armada XP platforms by using a simple
'i2cget' command to read an I2C EEPROM.
* The implementation was based on the fact that the offload engine
was re-programmed to transfer each message of an I2C xfer: this
meant that each message sent with the offload engine was starting
with a normal I2C start sequence. However, the I2C subsystem
assumes that all messages belonging to the same xfer will use the
so-called "repeated start" so that the entire I2C xfer is seen as
one transfer by the I2C devices and cannot be interrupt by other
I2C masters on the same bus.
In fact, the "I2C Bridge" allows to offload three types of xfer:
- xfer of one write message
- xfer of one read message
- xfer of one write message followed by one read message
For all other situations, we have to fallback to not using the "I2C
Bridge" in order to get proper I2C semantics.
Therefore, this commit reworks the offload implementation to put it
not at the message level, but at the xfer level: in the
mv64xxx_i2c_xfer() function, we decide if the transaction can be
offloaded (in which case it is handled by the
mv64xxx_i2c_offload_xfer() function), or otherwise it is handled by
the slow path (implemented in the existing mv64xxx_i2c_execute_msg()).
This allows to simplify the state machine, which no longer needs to
have any state related to the offload implementation: the offload
implementation is now completely separated from the slow path (with
the exception of the interrupt handler, of course).
In summary:
- mv64xxx_i2c_can_offload() will analyze an I2C xfer and decided of
the "I2C Bridge" can be used to offload it or not.
- mv64xxx_i2c_offload_xfer() will actually program the "I2C Bridge"
to offload one xfer (of either one or two messages), and block
using mv64xxx_i2c_wait_for_completion() until the xfer completes.
- The interrupt handler mv64xxx_i2c_intr() is modified to push the
offload related code to a separate function,
mv64xxx_i2c_intr_offload(). It will take care of reading the
received data if needed.
This commit was tested on:
- Armada XP OpenBlocks AX3-4 (EEPROM on I2C and RTC on I2C)
- Armada XP WRT1900AC (LED controller on I2C)
- Armada XP GP (EEPROM on I2C)
Fixes: 930ab3d403 ("i2c: mv64xxx: Add I2C Transaction Generator support")
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[wsa: fixed checkpatch warnings]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't need the mask since we obtain the channels via DT.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The first I2C slave provider using the new generic interface.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The first user of the i2c-slave interface is an eeprom simulator. It is
a shared memory which can be accessed by the remote master via I2C and
locally via sysfs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Finally(!), make Linux support being an I2C slave. Most of the existing
infrastructure is reused. We mainly add i2c_slave_register/unregister()
calls which tells i2c bus drivers to activate the slave mode. Then, they
also get a callback to report slave events to.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJUhj6JAAoJEILEb/54YlRxTM4P/j5g5SfqvY0QKsn7sR7MGZ6v
nsgCBhJAqTw3ocNC7EAs8z9h2GWy1KbKpakKYWAh9Fs1yZoey7tFSlcv/Rgjlp70
uU5sDQHtpE9mHKiymdsowiQuWgpl962L4k+k8hUslhlvgk1PvVbpajR6OqG8G+pD
asuIW9eh1APNkLyXmRJ3ZPomzs0VmRdZJ0NEs0lKX9mJskqEvxPIwdaxq3iaJq9B
Fo0J345zUDcJnxWblDRdHlOigCimglElfN5qJwaC4KpwUKuBvLRKbp4f69+wfT0c
kYFiR29X5KjJ2kLfP/wKsLyuDCYYXRq3tCia5M1tAqOjZ+UA89H/GDftx/5lntmv
qUlBa35VfdS1SX4HyApZitOHiLgo+It/hl8Z9bJnhyVw66NxmMQ8JYN2imb8Lhqh
XCLR7BxLTah82AapLJuQ0ZDHPzZqMPG2veC2vAzRMYzVijict/p4Y2+qBqONltER
4rs9uRVn+hamX33lCLg8BEN8zqlnT3rJFIgGaKjq/wXHAU/zpE9CjOrKMQcAg9+s
t51XMNPwypHMAYyGVhEL89ImjXnXxBkLRuquhlmEpvQchIhR+mR3dLsarGn7da44
WPIQJXzcsojXczcwwfqsJCR4I1FTFyQIW+UNh02GkDRgRovQqo+Jk762U7vQwqH+
LBdhvVaS1VW4v+FWXEoZ
=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
* acpi-scan:
ACPI: Add _DEP support to fix battery issue on Asus T100TA
* acpi-pm:
ACPI / sleep: Drain outstanding events after disabling multiple GPEs
ACPI / PM: Fixed a typo in a comment
* acpi-lpss:
dmaengine: dw: enable runtime PM
ACPI / LPSS: introduce a 'proxy' device to power on LPSS for DMA
ACPI / LPSS: allow to use specific PM domain during ->probe()
ACPI / LPSS: add all LPSS devices to the specific power domain
* acpi-processor:
ACPI / cpuidle: avoid assigning signed errno to acpi_status
ACPI / processor: remove unused variabled from acpi_processor_power structure
ACPI / processor: Update the comments in processor.h
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so some #ifdef blocks
depending on CONFIG_PM_RUNTIME may be dropped now.
Do that in drivers/i2c/busses/i2c-omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26 ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Switch Davinci I2C driver to use platform_get_irq(), because
it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
for requesting IRQ resources any more, as they can be not ready yet
in case of DT-boot.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can simply pass the pointer to the private structure to the irq
routine instead of passing the platform device and looking up its
driver_data.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for SCCB by implementing I2C_M_IGNORE_NAK and I2C_M_STOP
flags and advertising functionality flag I2C_FUNC_PROTOCOL_MANGLING.
Also fixed missing functionality flag I2C_FUNC_NOSTART.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 0f5768bf89 ("i2c: omap: implement workaround for handling
invalid BB-bit values") introduce the error result in boot test fault on
OMAP3530 boards.
The patch fix the error (disable i2c bus test for OMAP3530).
Reported-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 0f5768bf89 ("i2c: omap: implement workaround for handling invalid BB-bit values")
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CONFIG_OF_DYNAMIC enables runtime changes to the device tree which in
turn may trigger addition or removal of devices from Linux. Add an
OF_RECONFIG notifier handler to receive tree change events and to
creating or destroy i2c devices as required.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: clean up #ifdefs and drop unneeded error handling]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-i2c@vger.kernel.org
Dynamically inserting i2c client device nodes requires the use
of a single device registration method. Factor out the loop body of
of_i2c_register_devices() so that it can be called for individual
device_nodes instead of for all the children of a node.
Note: The diff of this commit looks far more complicated than it
actually is due the indentation being changed for a large block of code.
When viewed using the diff -w flag to ignore whitespace changes it can
be seen that the change is actually quite simple.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: Made new function static and removed changes to header]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-i2c@vger.kernel.org
Let's handle i2c interrupt re-configuration in i2c driver. This will
help us in removing some soc specific checks from machine files and
will help in removing static iomapping of SYS register in exynos.c
Also handle saving and restoring of SYS_I2C_CFG register during
suspend and resume of i2c driver.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we are using the clk notifier framework we get compile errors
without COMMON_CLK. But the driver fails to probe without COMMON_CLK
anyways, so just add that as a Kconfig dependency.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5.0 introduces _DEP (Operation Region Dependencies) to designate
device objects that OSPM should assign a higher priority in start
ordering due to future operation region accesses.
On Asus T100TA, ACPI battery info are read from a I2C slave device via
I2C operation region. Before I2C operation region handler is installed,
battery _STA always returns 0. There is a _DEP method of designating
start order under battery device node.
This patch is to implement _DEP feature to fix battery issue on the
Asus T100TA. Introducing acpi_dep_list and adding dep_unmet count
in struct acpi_device. During ACPI namespace scan, create struct
acpi_dep_data for a valid pair of master (device pointed to by _DEP)/
slave(device with _DEP), record master's and slave's ACPI handle in
it and put it into acpi_dep_list. The dep_unmet count will increase
by one if there is a device under its _DEP. Driver's probe() should
return EPROBE_DEFER when find dep_unmet is larger than 0. When I2C
operation region handler is installed, remove all struct acpi_dep_data
on the acpi_dep_list whose master is pointed to I2C host controller
and decrease slave's dep_unmet. When dep_unmet decreases to 0, all
_DEP conditions are met and then do acpi_bus_attach() for the device
in order to resolve battery _STA issue on the Asus T100TA.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=69011
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Tested-by: Adam Williamson <adamw@happyassassin.net>
Tested-by: Michael Shigorin <shigorin@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No functional changes.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Arbitration Lost is an expected situation in a multimaster
environment. I2C controller (IP) correctly detect and report AL.
The only one visible reason for resetting IP in the AL case is
to avoid advisory 1.94 (omap3) and errata i595 (omap4): "I2C:
After an Arbitration is Lost the Module Incorrectly Starts
the Next Transfer".
Errata workaround states: "The MST and STT bits inside I2C_CON
should be set to 1 at the same moment (avoid setting the MST bit
to 1 while STT = 0)." The driver never set MST and STT bits
separately and doesn't create condition for errata. So the reset
is not necessary.
Also corrected return value for AL to -EAGAIN.
Tested on Beagleboard XM C.
Tested on BBB and AM437x Starter Kit by Felipe Balbi.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In a multimaster environment, after IP software reset, BB-bit value doesn't
correspond to the current bus state. It may happen what BB-bit will be 0,
while the bus is busy due to another I2C master activity.
Any transfer started when BB=0 and bus is busy wouldn't be completed by IP
and results in controller timeout. More over, in some cases IP could
interrupt another master's transfer and corrupt data on wire.
The commit implement method allowing to prevent IP from entering into
"controller timeout" state and from "data corruption" state.
The one drawback is the need to wait for 10ms before the first transfer.
Tested on Beagleboard XM C.
Tested on BBB and AM437x Starter Kit by Felipe Balbi.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Delete STAT_AD0 mask as unrelated to current IP (omap1?).
Delete DEBUG conditional around SYSTEST masks group.
Add SYSTEST functional mode masks for SCL and SDA.
Add STAT_BF mask.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c input clock can change dynamically, e.g. on the RK3066 where
pclk_i2c0 and pclk_i2c1 are connected to the armclk, which changes
rate on cpu frequency scaling.
Until now, we incorrectly called clk_get_rate() while holding the
i2c->lock in rk3x_i2c_xfer() to adapt to clock rate changes.
Thanks to Huang Tao for reporting this issue.
Do it properly now using the clk notifier framework. The callback
logic was taken from i2c-cadence.c.
Also rename all misleading "i2c_rate" variables to "clk_rate", as they
describe the *input* clk rate.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Tested-by: Doug Anderson <dianders@chromium.org> on RK3288
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 6d9939f651 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f651 code doesn't correspond to workaround provided by
errata.
According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.
Restored pre 6d9939f651 way of handling errata.
Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f651 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since at91sam9g45 is now DT-only, all DMA capable users of this driver
are using the DT case, and the legacy support can be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the Designware core is configured with IC_EMPTYFIFO_HOLD_MASTER_EN
set to zero, allowing the TX FIFO to become empty causes a STOP
condition to be generated on the I2C bus. If the transmit FIFO
threshold is set too high, an erroneous STOP condition can be
generated on long transfers - particularly where the interrupt
latency is extended.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 1d7afc9594 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).
A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.
It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).
According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).
All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...
The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.
Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK
In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Cc: <stable@vger.kernel.org> # v3.7+
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes the following kbuild test robot warning:
>> drivers/i2c/busses/i2c-dln2.c:70:1-4: WARNING: end returns can be simplified if negative or 0 value
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It should be the DMA device, not the platform device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SCB is present on IMG SoCs other than the META-based TZ1090,
such as the MIPS-based Pistachio SoC. Relax the Kconfig dependency
so that it can be built on any MIPS or META machine.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the topology clearer. For instance, by adding a pca9547
device with address 0x70 to bus i2c-0, you get:
/sys/class/i2c-dev/i2c-0/device/0-0070/channel-0 -> i2c-1
...
/sys/class/i2c-dev/i2c-0/device/0-0070/channel-7 -> i2c-8
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[wsa: simplified sysfs-usage and fixed format string usage]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Martin Belanger <martin.belanger@cyaninc.com>
Acked-by: Danielle Costantino <danielle.costantino@gmail.com>
The current implementation creates muxed i2c-<n> busses as immediate
children of their i2c-<n> parent bus. In case of multiple muxes on one
bus, it is impossible to determine which muxed bus comes from which mux.
It could be argued that the parent device should be changed from the
parent adapter to the mux device. This has pros and cons. To improve the
topology, simply add a "mux_device" symlink pointing to the actual
muxing device, so we can distinguish muxed busses. Doing it this way, we
don't break the ABI.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
No need to initialize 'ret' if it gets assigned directly after that.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add dma support for i2c. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
DMA is optional, even DMA request unsuccessfully, i2c can also work well.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 2fd36c5526 ("i2c: core: Map OF IRQ at probe time"),
i2c slaves without interrupts (e.g. da9210 and at24 on r8a7791/koelsch)
fail to probe:
at24: probe of 2-0050 failed with error -22
da9210: probe of 6-0068 failed with error -22
This happens because the call to of_irq_get() in i2c_device_probe()
returns -EINVAL.
If a device node does not have an "interrupts" property,
of_irq_parse_one() fails. Unlike irq_of_parse_and_map(), of_irq_get()
does not ignore errors from of_irq_parse_one(), but forwards them.
Make i2c_device_probe() ignore all errors but -EPROBE_DEFER to fix this,
just like platform_get_irq() and platform_get_irq_byname() already do.
Fixes: 2fd36c5526 ("i2c: core: Map OF IRQ at probe time")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver tried to access device registers with the (little-endian)
iowrite/ioread functions. While this worked on little-endian machines
(e.g. Microblaze with AXI bus), it made the driver unusable on
big-endian machines (e.g. PPC405 with PLB).
During the probe function, the driver tried to write a 32-bit reset mask
into the reset register. This caused an error interrupt on big-endian
systems, because the device detected an invalid (byte-swapped) reset
mask. The result was an Oops.
The patch implements an endianness detection similar to the one used in
other Xilinx drivers like drivers/spi/spi-xilinx.c. It was tested on a
PPC405/PLB system.
Signed-off-by: Thomas Gessler <Thomas.Gessler@exp2.physik.uni-giessen.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No user needs magic hex values, makes this debug output. Add DMA info.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address is still handled using the old state
machine, it is sending the actual data that is done via DMA. This is
least intrusive and allows us to work with the message buffers directly
instead of preparing a custom buffer which involves copying the data
around.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed an uninitialized var problem]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improves readability and reduces chances of duplicates.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Amend the at91 i2c pin controller to set the state of the pins to:
- "default" on resume.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enforces correct I2C error returned codes from Freescale's
MPC i2c bus driver, allowing for proper user-space/kernel error
handling.
Signed-off-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't log the host status register value in i801_isr(), it has very
little value and fills up the log when debugging is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
