- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcO/B7AAoJEFBXWFqHsHzOsl4IAL1ubDbUA4T+mbL5joEdmZYZ
iOBVLq5L22uyqUU0i3qSoRi0Tym0ZKXJvP1XdNTlK4fJgabTlvJFlIssBM1FhUMk
pmIDrlCZeoMY1iIJ2OHQ9On9njRA/B+ClZFzFAPR/8iLMC70RB5NMKa8uXYxSQ21
EGjIlNsITD4F/IGt9eqdgt5fnfewgbnumxehvbcYPdreXVRuAyWXlPtc17mI+uof
DmnfANdDZ/VREGJwekQIu2D/VRo6jfC5jc24ixX4Fp5kPZ0CGmXxRzQmTVcm9QQ4
3jRMKf2PXlvW5vcqXLMoGJljVbeYITrF7ycswHge0LPs37ghjW+crAv5TzN6Agg=
=HZIA
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0:
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
* tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the uart1 node such that the clock will be enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the lpc_ctrl node in the quanta-q71l dts such that the LPC_CLK is
enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added uart2 and uart3 in Facebook Tiogapass for routing serial input
from Host to BMC for SoL via LPC.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added lpc control for enabling lpc clock and lpc snoop devices to
Facebook Tiogapass device tree.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add reset property for dma, can and sdram on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Commit 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") moved some omap4 timers to probe with ti-sysc
interconnect target module. Turns out this broke pwm-omap-dmtimer
for reparenting of the timer clock.
With ti-sysc, we can now configure the clock sources in the dts with
assigned-clocks and assigned-clock-parents.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A CPUfreq driver, like the ARM big.LITTLE driver used on the TC2 board,
which provide the Energy Model with power cost information via the
PM_OPP of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The compatible string for the LCD panel used for the Q8 tablets are just
a placeholder that was shown to be compatible with the actual panels
found on these devices. The real panels do not have any identifiable
markings and vary between production runs.
The compatibe string previously used had a pixel clock that could not
be accurately reproduced on Allwinner hardware, and discussions on
whether a margin should be added to the display drivers and how large
a margin was acceptable had stalled.
Now that we have a panel model that is actually used with Allwinner
hardware, has the same dimensions, and the timings have been shown to
work with the nameless panels, we can use that one instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A13 Q8 tablet, following the A13 reference tablet design, has the
system's fixed 3.3V rail feed the VCC supply of the LCD panel.
Additional voltage rails used by the panel are generated using a
regulator fed from the unregulated IPSOUT output of the PMIC. The latter
is unrepresentable in the device tree. Both are controlled with MOSFETs
by the enable GPIO added in the previous patch. The actual enable or
reset pin for the panel is tied directly to LCD-VCC after the MOSFET.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the AXP209 GPIOs, we can toggle the LCD panel enable
line. Add the GPIO phandle to the panel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The panel backlight and enable GPIO comments were incorrectly placed
in the input port, while it should have been in the panel node itself.
Move them to the correct position.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the GPIOs on the AXP209, we can control the LCD
backlight with them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.
Remove all disable-wp from emmc or sdio controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The change removes redundant #address-cells and #size-cells properties from
gpio-keys-polled compatible device nodes found in lpc4357-ea4357-devkit and
lpc4350-hitex-eval board DTS files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Commit 225da7e65a ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7c ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Q8 tablets follow the A23/A33 tablet reference design, and normally
use a "generic" 800x480 LCD panel. The actual panel may vary between
production runs, and there are no visible markings denoting its model.
This patch uses a panel that has the same dimensions and timings that
are close to what was provided in the vendor fex files.
Since there are also A33 Q8 tablets with 1024x600 panels, this patch
only sets the compatible string for A23 Q8 tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Q8 design for A23/A33 tablets have an 18-bit RGB LCD panel connected
to the LCD interface on the SoC, the DC1SW output on the PMIC providing
power for the LCD, and PH7 toggling the reset pin for the panel.
This patch adds a device node for the panel, describing the above, and
enables the display pipeline.
The actual model or compatible string for the panel should be added in
the tablet device tree file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the compatible strings for the display pipeline on the A23 have
been added to the bindings, add the corresponding compatibles to the
device nodes already in the A23/A33 shared dtsi.
While the A23 has the TCON ch1 clock defined in the CCU, and the channel
1 registers are available, it does not have any means to use channel 1
due to a lack of downstream encoders, and the enable bit for channel 1 is
hard-wired to 0 (off). Hence the ch1 clock is left out.
As the MIPI DSI output device is not officially documented, and there
are no reference devices to test it, it is not covered by this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
Fixes: d7b843df13 ("ARM: dts: sun8i: add NAND controller node for A23/A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is an ARM + FPGA instrumentation board used at telescopes in
Antarctica, Chile, and Canada:
https://pole.uchicago.edu/https://arxiv.org/abs/1608.03025https://chime-experiment.ca/
With these commits and a suitable userspace, we can boot the board, load
a FPGA bitstream, and communicate with the RTL design. Most of the board's
telemetry sensors (temperatures, voltages) are functional but detailed
testing is to follow.
We are weaning ourselves off TI's "official" kernel for this SOC, which
has been stuck at 2.6.37 and is not really fit for use. To anyone at TI:
despite good silicon and some dedicated support enginers, your
open-source software strategy for these parts has not worked well.
Please get in touch with me if you'd like to have a constructive
discussion about ways to improve it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: dropped fpga@1 as linux,spidev is still undocumented]
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ethernet works in kernel only if we use some binary u-boot from the
past which have support for KS8851.
The u-boot sources are not available for this mysterious u-boot image
people tends to hold on... Mainline u-bott does not have ethernet support
for sdp4430 and if we use that the ethernet is not working.
After some debugging I have managed to get the ethernet working with
mainline u-boot while not breaking the networking with the case when we
boot with the mysterious binary u-boot.
Basically we were missing bunch of pinmux settings and the 'magic'
gpio_138 handling in kernel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the legacy "linux,wakeup" boolean property is already replaced
with "wakeup-source". However few occurrences of old property has popped
up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit aeda5003d0 ("Input: matrix_keypad - change
name of wakeup property to "wakeup-source"")
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the unnecessary properties #address-cells and #size-cells
of node pinmux as there are no child-nodes with property reg.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it. Code was tested on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Drop the A31 fallback compatible.
Fixes: f89120b6f5 ("ARM: dts: sun8i: Add the H3/H5 CSI controller")
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of
IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs.
ARM GIC only supports active-high interrupts for SPI (Shared Peripheral
Interrupts), and the Palmas PMIC by default is active-low.
Palmas PMIC allows changing the interrupt polarity using register
PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with
a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the
Palmas RTC interrupts stop working. This can be easily tested with
kernel tools rtctest.c.
Turns out the SoC inverts the sys_nirq pins for GIC as they do not go
through a peripheral device but go directly to the MPUSS wakeupgen.
I've verified this by muxing the interrupt line temporarily to gpio_wk16
instead of sys_nirq1. with a gpio, the interrupt works fine both
active-low and active-high with the SoC internal pull configured and
palmas polarity configured. But as sys_nirq1, the interrupt only works
when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC.
Note that there was a similar issue earlier with tegra114 and palmas
interrupt polarity that got fixed by commit df545d1cd0 ("mfd: palmas:
Provide irq flags through DT/platform data"). However, the difference
between omap5 and tegra114 is that tegra inverts the palmas interrupt
twice, once when entering tegra PMC, and again when exiting tegra PMC
to GIC.
Let's fix the issue by adding a custom wakeupgen_irq_set_type() for
wakeupgen and invert any interrupts with wrong polarity. Let's also
warn about any non-sysnirq pins using wrong polarity. Note that we
also need to update the dts for the level as IRQ_TYPE_NONE never
has irq_set_type() called, and let's add some comments and use proper
pin nameing to avoid more confusion later on.
Cc: Belisko Marek <marek.belisko@gmail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
cd pin on mmc1 is GPIO_ACTIVE_LOW not GPIO_ACTIVE_HIGH
Fixes: e63201f194 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We're currently getting a warning with make dtbs:
arch/arm/boot/dts/omap3-gta04.dtsi:720.7-727.4: Warning (graph_port):
/ocp@68000000/dss@48050000/encoder@48050c0 0/port: graph node unit
address error, expected "0"
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong polarity of card detect GPIO pin leads to the system not
booting from external mmc, if the back cover of N900 is closed.
When the cover is open the system boots fine.
This wasn't noticed before, because of a bug, which was fixed
by commit e63201f19 (mmc: omap_hsmmc: Delete platform data GPIO
CD and WP).
Kernels up to 4.19 ignored the card detect GPIO from DT.
Fixes: e63201f194 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enable HDMI output on sun8i-h3-nanopi-m1-plus.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for Renesas RZ/A2M evaluation board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/A2 (R7S9210) SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41f ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is to add external trigger stamp fifo support
for 1588 timer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the device tree bindings for USB OTG support. Driver was tested
using on a LG Nexus 5 (hammerhead) phone. This patch is based on work
from Jonathan Marek and from the other msm8974 devices.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the gpio-ranges property to pm8941_gpios so that the GPIO
pins are initialized by the GPIO framework and not pinctrl. This fixes
a circular dependency so GPIO hogging can be used on this board.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds WiFi support to the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: Enabled wlan_regulator_pin and wlan_sleep_clk_pin]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
All the GSBI blocks are marking their GIC IRQ lines as
"IRQ_TYPE_NONE" but there is no such thing: all GIC IRQ
lines have a trigger type.
That yields the following warning from the GIC driver:
WARNING: CPU: 0 PID: 1 at ../drivers/irqchip/irq-gic.c:1016
gic_irq_domain_translate+0xdc/0xe4
(...)
Mark all of these IRQ_TYPE_LEVEL_HIGH as is common so this
warning goes away.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The GSBI module complains:
gsbi 16500000.gsbi: missing mode configuration
gsbi: probe of 16500000.gsbi failed with error -22
gsbi 16600000.gsbi: missing mode configuration
gsbi: probe of 16600000.gsbi failed with error -22
gsbi 19800000.gsbi: GSBI port protocol: 2 crci: 0
So we should mark these GSBIs as "disabled" in the SoC
file by default.
If boards appear that make use of them, we can simply
set status = "ok" in the DTS for them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Vexpress motherboard MMCI requires dedicated interrupts for CMD and PIO,
which obviously should be expressed as a list. Current form uses tuple
and it works fine since interrupt-cells equal to 1.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
MPS2 UART requires dedicated interrupts for RX, TX and overflow, which
obviously should be expressed as a list. Current form uses tuple and
it has worked so far because NVIC has interrupt-cells equal to 1.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Inspur on5263m5 is an Intel Xeon OCP server that uses the ASPEED
AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
[joel: Rework commit message]
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds nodes for the Video Engine and the associated reserved memory
for the A10. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A10 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on Rev. 1.00 of the R-Car H1 datasheet.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The timer interrupts specified in commit 3652e2741f ("ARM: dts:
da850: Add clocks") are wrong but since the current timer code
hard-codes them, the bug was never spotted.
This patch must go into stable since, once we introduce a proper
clocksource driver, devices with buggy device tree will stop booting.
Fixes: 3652e2741f ("ARM: dts: da850: Add clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Added ADC and other sensor devices present in the Facebook Tiogapass
machine.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the description of the four Keyboard Controller Style (KCS)
IPMI communication channels present in the ASPEED BMC. They are disabled
by default.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Allows the GPIO controller to be used as an interrupt parent.
of_irq_find_parent() skips interrupt controller nodes that do
not have the #interrupt-cells property.
Signed-off-by: Mark Walton <mark.walton@serialtek.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add Delta Electronics power supply DPS-650-AB.
Signed-off-by: Xiaoting Liu <xiaoting.liu@hxt-semitech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Device tree binding of Memory Controller has been changed: GART has been
squashed into the MC, there are a new mandatory clock and #iommu-cells
properties, the compatible has been changed to 'tegra20-mc-gart'.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add reset property for gpio, i2c, sdmmc, nand, qspi, spi, uart, and
watchdog on base socfpga and socfpga_arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This matches licensing used by other BCM53573 files and BCM5301X.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXDjK7AAKCRALBhiOFHI7
1eZfAJ0X/MrjG/MB1NSlJ2kUGmBs5MnnswCdFZpNF4okkjtwyWoCoBsp9X3kUkw=
=vYNz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 5.0
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX6SX has same GPT type as i.MX6DL, in GPT driver, it uses
below TIMER_OF_DECLARE, so the backward compatible should be
"fsl,imx6dl-gpt", correct it.
TIMER_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
rv1108-elgin-r1 board is based on Rockchip RV1108 SoC.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the pin settings for the SPI pins so they can be used across
multiple boards.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pass the 'dma-names' property to the SPI ports so that DMA can
be supported.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the core display subsystem and vop nodes to rk3066.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Define the required properties to enable I2C bus recovery supported by
the I2C subsystem.
This patch adds GPIO based I2C fault injector for Digi Connectcore SOM.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds definitions for ESDHC1 for Digi Connectore SOM & JSK.
This interface can be used to boot a module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In fact, the RTC battery can only be connected outside the module,
so this patch moves the PMIC RTC property and its power from SOM dts
to JSK.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The interrupt controller is located at the physical address 0x10040000.
This patch changes the unit name of the controller to reflect the actual
address.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of the legacy "gpio-key,wakeup" and "enable-sdio-wakeup" boolean
properties are already replaced with "wakeup-source". However few
occurrences of old property has popped up again, probably from the
remnants in downstream trees. Almost all of those were remove couple
of years back.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit 700a38b27e ("Input: gpio_keys - switch to using
generic device properties") and commit 0dbcdc0622 ("mmc: core: enable
support for the standard "wakeup-source" property")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dspi3 is used as slave controller on vf610-bk4, and the default
'#address-cells = <1>;' setting in vfxxx.dtsi causes the following DTC
warning.
DTC arch/arm/boot/dts/vf610-bk4.dtb
../arch/arm/boot/dts/vfxxx.dtsi:550.24-563.6: Warning (spi_bus_bridge): /soc/aips-bus@40080000/spi@400ad000: incorrect #address-cells for SPI bus
also defined at ../arch/arm/boot/dts/vf610-bk4.dts:107.8-119.3
arch/arm/boot/dts/vf610-bk4.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
For spi device used as slave controller, '#address-cells' should be 0.
Let's overwrite the property in vf610-bk4.dts to fix the warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NHK15 panel is specified inside the display controller,
which works for the DPI-type DT parsing the old fbdev code
used, but for the DRM driver it needs to be spawn as its own
device, so we move it out of the display controller.
We also drop the panel timings: this should be determined
by the hardware or a device-specific compatible string, not
by this type of encoding into the device tree. It turns out
that this hardware is strapped to the right configuration
at boot already and we the driver just reads out the
hardware-specified resolution and timings. Drop the
"panel,dpi" compatible string altogether.
Fix a comment error in the DTS file while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add num-viewport property for PCIe DT nodes to specify how many
viewports are implemented.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on the MXIII-Plus. The MMC dt-bindings
specify: "[...] using the "cd-inverted" property means, that the CD line
is active high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: 35ee52bea6 ("ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
After commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on the EC-100. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: bbedc1f1d9 ("ARM: dts: meson8b: Add support for the Endless Mini (EC-100)")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
After commit 89a5e15bcb ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: e03efbce6b ("ARM: dts: meson8b-odroidc1: add microSD support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the Mali-450 GPU and it's OPP table for Meson8. The GPU uses two
pixel processors in this configuration. The OPP table is taken from the
3.10 vendor kernel which uses the following table:
FCLK_DEV5 | 1, /* 255 Mhz */
FCLK_DEV7 | 0, /* 364 Mhz */
FCLK_DEV3 | 1, /* 425 Mhz */
FCLK_DEV5 | 0, /* 510 Mhz */
FCLK_DEV4 | 0, /* 637.5 Mhz */
This describes the mux (FCLK_DEVx) and a 0-based divider in the clock
controller. "FCLK" is "fixed_pll" which is running at 2550MHz.
The "turbo" setting is described by "turbo_clock = 4" where 4 is the
index of the table above.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the Mali-450 GPU and it's OPP table for the Meson8 and Meson8m2 (the
latter inherits meson8.dtsi).
These SoCs have a Mali-450 GPU with six pixel processors. The OPP table
is taken from the 3.10 vendor kernel which uses the following table:
FCLK_DEV7 | 1, /* 182.1 Mhz */
FCLK_DEV4 | 1, /* 318.7 Mhz */
FCLK_DEV3 | 1, /* 425 Mhz */
FCLK_DEV5 | 0, /* 510 Mhz */
FCLK_DEV4 | 0, /* 637.5 Mhz */
This describes the mux (FCLK_DEVx) and a 0-based divider in the clock
controller. "FCLK" is "fixed_pll" which is running at 2550MHz.
The "turbo" setting is described by "turbo_clock = 4" where 4 is the
index of the table above.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Various peripherals (Mali GPU, NAND controller, VPU; etc.) are located
in the APB bus. Describe this bus so we can add devices to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Various peripherals (Mali GPU, NAND controller, VPU, etc.) are located
in the APB bus. Describe this bus so we can add devices to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Mali GPU and the DVB demulator are located in the APB2 bus. Describe
this bus so we can add devices to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: 9c15795a4f ("ARM: dts: meson8b-odroidc1: ethernet support")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
LDO20 regulator provides power for the MMC card on Odroid U3 boards. That
regulator has been marked as 'boot-on' since the beginning of Odroid X/U3
support, but such flag is not really needed for it. That regulator is
correctly described as supply for eMMC card and controlled by its driver.
Commit 05f224ca66 ("regulator: core: Clean enabling always-on regulators
+ their supplies") changed the way the boot-on regulators are handled and
since then regulators marked as 'boot-on' got increased reference count
and are not turned off for the system suspend time.
The new approach turned out to break suspend/resume support on Odroid U3
with eMMC card, because the card is not properly shutdown due to missing
of power cycle. Fix this by removing excessive 'boot-on' flag and let
MMC driver to control turning power on and off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Bindings of the fixed-regulator, which precedes support for GPIO flags
passed via phandle descriptor, introduced its own method annotating
that the given GPIO line is active low or high - by using
'enable-active-high' property. The driver always ignored flags passed
via GPIO descriptor.
Fix the conflicting GPIO flags to match the status forced by the
'enable-active-high' property to avoid future confusion.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the DTC warning for xti node:
arch/arm/boot/dts/s3c2416-smdk2416.dts:23.12-28.5:
Warning (simple_bus_reg): /clocks/xti: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to Devicetree specification, the unit-address must match the
first address specified in the reg property of the node. Fix the DTC
warning onenand node:
arch/arm/boot/dts/s5pv210.dtsi:81.29-93.5:
Warning (simple_bus_reg): /soc/onenand@b0000000: simple-bus unit address format error, expected "b0600000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
This commit adds DMC (Dynamic Memory Controller) nodes, which are needed
by S5Pv210 cpufreq driver to work.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen, connected to I2C-2
- Broadcom BCM4329 Bluetooth over UART-0
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
THis commit adds memory reservation required by MFC (Multi Format Codec)
to run. On S5PV210 both regions needs to be on separate memory banks.
Size of both regions is taken from vendor Linux kernel sources.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.
Fixes: 1b90e06b14 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds the actual VGA DAC bridge that is used in the
Versatile AB, and sets the mode to 640x480 VGA and
routes the CLCD pads appropriately.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Invalid supply voltage(s) AVDD: -22, DVDD: -22
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Too high supply voltage(s) AVDD: 5000000, DVDD: 5000000
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The LS1021A has a memory controller that supports EDAC. This commit
adds an entry for it.
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All the I2C devices connected to the I2C0 bus are capable of
running at 400kHz, so run it at a higher frequency.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7ULP can switch CPU between RUN mode and HSRUN mode
by programming SMC1 register, different clock sources
will be used for CPU in different modes, so SMC1 can be
abstracted as a clock controller for CPU clock switch,
this patch adds support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add devicetree support for 96Boards Chameleon96 board from Novtech, Inc.
based on Altera CycloneV SoC FPGA. This board is one of the Consumer
Edition boards of the 96Boards family and has the following key features:
* SoC - Intel Cyclone V SoC FPGA
* GPU - Graphics based on Intel Video Suite for FPGA
* RAM - 512MB DDR3L
* USB - 2x USB2.0 Host, 1x USB2.0 OTG
* Wireless - Wifi, BT
More information about this board can be found in 96Boards product
page: https://www.96boards.org/product/chameleon96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, the board's
fixed 3.3V power regulator provides overall power via VBAT and I/O power
via VDDIO. The RTC clock output from the SoC provides the LPO low power
clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators
provide power to the WiFi+BT module, which is based on the Broadcom
BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply
up to 200 mA. The datasheet of the chip suggests a maximum power draw of
up to 360 mA when transmitting, thus requiring two outputs from the PMIC
to handle the load. However the device tree only references one of them,
leaving the other unused and possibly turned off.
This patch marks both as always-on, since we don't have a proper binding
to specify two regulators as "bound together". The name and constraints
of DLDO2 are also added.
Fixes: da7ac948fa ("ARM: dts: sun8i: Add board dts file for Banana Pi M2
Ultra")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
CLK_OUT_A, an external clock output function driven from the clock
control unit, on the R40 is sometimes used to provide a low rate low
power clock to a WiFi or Bluetooth controller.
This patch adds a pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
UART3 on the PG pingroup on the R40 SoC is commonly used to connect the
bluetooth controller in a WiFi+Bluetooth combo chip, with the WiFi bits
also on the PG pingroup.
This patch adds two device nodes for UART3 on PG pingroup, one for the
RX/TX pins, and one for the RTS/CTS pins. Consumers can reference either
just the RX/TX pinmux setting or both, depending on the application.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Because "ethernet0" alias is missing, U-Boot doesn't generate board
specific MAC address. Effect of this is random MAC address every boot
and thus new IP address is assigned to the board.
Fix this by adding alias.
Fixes: 7389172fc3 ("ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Maxime: Removed unneeded comment]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The osc24M clock does not have a "clock-output-names" property, which
means that the clock name is derived from the node name in Linux. The
node name was changed in commit acfd5bbe26 ("ARM: dts: sun6i: Change
clock node names to avoid warnings"). This breaks Linux as the sunxi-ng
clock driver implicitly depends on the external clock being named
"osc24M".
Add a "clock-output-names" property to restore the previous behavior.
Fixes: acfd5bbe26 ("ARM: dts: sun6i: Change clock node names to avoid
warnings")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the legacy "gpio-key,wakeup" property are already replaced
with "wakeup-source". However few occurrences of old property has
popped up again, probably from the remnants in downstream trees.
Almost all of those were remove couple of years back.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the commit 700a38b27e ("Input: gpio_keys -
switch to using generic device properties")
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Looks like I accidentally left some extra flags for uart3 to
not idle it. This happened as I generated the data from a
running system where these flags are set dynamically on boot
by omap_hwmod_setup_earlycon_flags() if earlycon is enabled.
We can just remove them.
Fixes: 4c38798461 ("ARM: dts: omap5: Add l4 interconnect hierarchy and ti-sysc data")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since we have U-Boot (flashed in place of stock kernel), it's not needed
anymore to hardcode bootargs on every Aries-family board.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
[krzk: Squash changes to fascinate4g and galaxys into one commit]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since we have separate compatible for S5Pv210 FIMD, let's use it rather
than using one from Exynos4210.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add node for Exynos Rorator device, so it can be used on all S5Pv210
based devices.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We're now getting the following error:
genirq: Setting trigger mode 1 for irq 230 failed
(regmap_irq_set_type+0x0/0x15c)
cpcap-usb-phy cpcap-usb-phy.0: could not get irq dp: -524
Cc: Sebastian Reichel <sre@kernel.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N950/N9 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on both Nokia N950 and N9.
Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Watchdog node is incorrectly placed on r8a7743 SoC dtsi. This patch fixes
the sorting order.
Fixes: b5beb5d4c8 ("ARM: dts: r8a7743: Add watchdog support to SoC dtsi")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch removes aliases from SoC dtsi tree. Device aliases are
board-specific, if needed define it in board dts rather than SoC
dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The iic3 block on RZ/G1M does not support automatic transmission, unlike
other R-Car SoC's. So dropping the compatibility with the generic version.
Fixes: f523405f2a ("ARM: dts: r8a7743: Add IIC cores to dtsi")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch fixes sorting of vsp and msiof nodes.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable NXP pcf85263 real time clock for the iWave SBC based on RZ/G1C.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 6d2ca85279 ("dt-bindings: display: renesas: Deprecate
LVDS support in the DU bindings"), the internal LVDS encoder has DT
bindings separate from the DU. The Lager device tree was ported over to
the new model, but the Stout device tree was forgotten.
Fixes: 15a1ff30d8 ("ARM: dts: r8a7790: Convert to new LVDS DT bindings")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The bananapi has all its bank regulators tied to the 3v3 static regulator.
Make sure it's properly represented.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is necessary to use 'perf' for cache profiling etc.
Tested on cubieboard with 'perf stat echo foo'.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Edison tablet uses a Focaltech touchscreen, with one speciality
that the touchscreen resolution doesn't match the display resolution
(1024x768 vs. 1280x600) which userspace will have to compensate for.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The powerdown pin for the second camera is gpio3_b5 not b4,
so fix that. We don't have a working camera setup yet, so this
is not really critical, but nevertheless better to have fixed
already.
Fixes: 36ead91499 ("ARM: dts: rockchip: add BQ Edison 2 QC devicetree")
Reported-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A MK808 TV stick with rk3066 processor boots normal with logo
and console, but after booting the monitor remains black.
This patch fixes a vblank wait time out by adding HCLK_HDMI
to the vio power-domain node.
The HCLK_HDMI clock is now part of the logic
that enables the RK3066_PD_VIO power domain.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip i2s controller always only has one output connection
hence #sound-dai-cells is always 0. Therefore define it in the soc
dtsi itself instead of in individual boards.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While the rk3066 does have 2 camera interfaces, the rk3188 does not, so
there also isn't a QoS block for that non-existing interface, so remove it.
Fixes: e6e1869f0b ("ARM: dts: rockchip: add rk3066/rk3188 power-domains")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a fragment,
that later gets filled in on later releases, and in some cases it's
near-complete platform support. The latter is more common for derivative
platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions. Allwinner
support for F1C100s, a quite old SoC (ARMv5-based) shipping in the
Lychee Pi Nano platform. At the other end is NXP Layerscape LX2160A,
a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O aimed at
infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to devicetree,
which opens up for removal of even more of their platform-specific
'hwmod' description tables over the next few releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board
-----BEGIN PGP SIGNATURE-----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=sFVi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug console setups
- SoCFPGA adds explicit selection of ARM errata and removes some unused code
This tag also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release.
-----BEGIN PGP SIGNATURE-----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=m7me
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
-----BEGIN PGP SIGNATURE-----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=dIrg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a small pull request for some lingering things that didn't make
the first round of patches.
First, the new suniv device tree included device tree headers for the
clock and reset indices. These header filers are going in through the
clock tree. Thus with the dt and core branches in arm-soc alone, it
doesn't build. One fix is included to remove the #include statements.
The defined macros aren't used yet as they were properly removed during
the review phase.
Second, Bluetooth using Broadcom (now Cypress) chips connected to UARTs
on various boards is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
-----BEGIN PGP SIGNATURE-----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=FiER
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21 - round 2
This is a small pull request for some lingering things that didn't make
the first round of patches.
First, the new suniv device tree included device tree headers for the
clock and reset indices. These header filers are going in through the
clock tree. Thus with the dt and core branches in arm-soc alone, it
doesn't build. One fix is included to remove the #include statements.
The defined macros aren't used yet as they were properly removed during
the review phase.
Second, Bluetooth using Broadcom (now Cypress) chips connected to UARTs
on various boards is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
ARM: dts: suniv: Fix improper bindings include patch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcFg+pAAoJEFBXWFqHsHzOC3UH/RsA0ysBXsaUF9aNpfmwFpKP
bApnoyo+MhLZSvFqD8eU1K0BhXFOkOmMXMbTle0b3uF7qaknnXEoWTCNz+hJGDsz
fFeOqz7xjyG8Q4U8PT4ImG0OPuFNNGBs1byJKZygxJp/xBlAGMKDp/rRKbM4c8+8
WzoKcWcLqFe+Vau0vuesjcT7J/B3nWvzOWsWX5MHOp10rEWyv9Y4Ct3cAzSMVhAM
1eLQpYegOvUckX0if7BZpj7vSIhDNp/urx6U7D5KGAf9iHK50euMX55LhveiSM8w
CdnnZn2MUXEt2A81Aqb97IOhMsEra47Ffomr1nIV2OGbmDY27HrlUrNSEKNER28=
=I3dR
-----END PGP SIGNATURE-----
Merge tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale QSPI device tree cleanup for 4.21:
- It contains a series from Schrempf Frieder that cleans up FSL QSPI
device tree nodes. The current device trees are broken because they
use an inconsistent scheme for assigning the reg properties. It
becomes a problem with ongoing QSPI driver under SPI framework. So
the cleanup is a preparation for new driver landing in the next
cycle.
* tag 'imx-qspi-dt-clean' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The clock and reset bindings are going through different trees, and while
the patch doesn't contain any value defined in that header, it still
includes those files and result in a build breakage when building the DT
without the matching clock and reset patches applied.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This big set of changes adds SoC specific l4 interconnect target module
device tree data for am335x, am437x, omap5 and dra7 SoCs. We also move
existing devices to the right location in the l4 interconnect hierarcy.
This is similar to what we've already done for omap4 l4 interconnects
earlier, and follows what is documented in the ti-sysc driver dts binding
in Documentation/devicetree/bindings/bus/ti-sysc.txt.
These changes will essentially replace the struct ti_sysc and clock
entries in the arch/arm/mach-omap2/omap_hwmod_*_data.c files. Then a few
merge windows later, we can start dropping the built-in platform data
from the omap_hwmod_*_data.c files in favor of the device tree data only.
For now, we verify the device tree data module data against the built-in
data and warn about changes to prevent regressions.
With the device tree data, we are also probing devices with the ti-sysc
interconnect target module instead of omap_device. This fixes up the
handling for multiple device instances in a single interconnect target
module that has caused trouble earlier. A custom wrapper driver has been
needed earlier for such cases.
And as the device tree data is organized by the l4 interconnect instances,
we will be able to use genpd later on. This is because each interconnect
instance is also often also a single power domain.
This series of changes has been brewing for several months now. I did not
want to send a pull request earlier as people were still seeing device
specific issues until recently though. However, it turned out that all the
issues were quite trivial to fix. I had missed adding device tree ranges
for the l3 data port used on some devices, and I had missed converting the
device addresses for a few devices. And some devices like needed fixes for
deferred probe handling such as the EHCI PHY for built-in case on omap5.
Anyways, in case of trouble, we can easily just revert changes for a
single device if needed.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlwSnO8RHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXPDYRAAxDrbMVGPnPtyR2uYI/xKdwB7wlJWZNWe
nPOl1aMZ2bBmMH81WVXu6Q0h7kFC9Tuf3CG+xGdfT7XMgg28dOD0q3xfSyGwNn8q
ftWVLpbsmc0Qp7h78lK16kbdRWp5N4Qb3QGelXfz/T5jX7NtfDhjZ5dfuZgb4W8r
sI3gLeNEwK4hQB88kPmvuvXPqJflTGDKuXuNcR+jvvSVyl/vZq7akKLnGnSjaRHc
qedh85c/UV/TBqlxnruW8K9J9Tg/DDImzWRpfZSbIT9Y6TiRmihUeffUZkEYHkMt
tRg39nYeVq5BISccyGbT9AkkMqsjUAc7isBsBYWls9jpNwXHypMeHsqzraFcjgK+
f5lPEWmCVy2gyGZB94jPnm6Du27JhCRfzjFNkGDZ0AHdmnuQ8fuas0z8cOvDa0oD
sndg6nXmxnRr3+H5je10mVQaV6+EhP8DFe85KquM4anRo6LysZgBGkH2xG0iY64a
vi59yiAfepZrtFIkaIypOUZvpFUUVXT0RDSW9K6dFEwYCMLfNww8W9paHVErY6HA
aGTAn/rixUVBpEDH5d7eRK0Lk6swRk25zvYjGjppFGDEKjeztJaEVFRFYOrx6FTm
LwW/DZe2P+AdVPgKVM4anVSELzt5zC3WgLkiA1/ijcrhZxh/BIuYhh2FbRKyMRhp
t1h1SorsMT8=
=9lDj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add interconnect target module dts data for omaps for v4.21
This big set of changes adds SoC specific l4 interconnect target module
device tree data for am335x, am437x, omap5 and dra7 SoCs. We also move
existing devices to the right location in the l4 interconnect hierarcy.
This is similar to what we've already done for omap4 l4 interconnects
earlier, and follows what is documented in the ti-sysc driver dts binding
in Documentation/devicetree/bindings/bus/ti-sysc.txt.
These changes will essentially replace the struct ti_sysc and clock
entries in the arch/arm/mach-omap2/omap_hwmod_*_data.c files. Then a few
merge windows later, we can start dropping the built-in platform data
from the omap_hwmod_*_data.c files in favor of the device tree data only.
For now, we verify the device tree data module data against the built-in
data and warn about changes to prevent regressions.
With the device tree data, we are also probing devices with the ti-sysc
interconnect target module instead of omap_device. This fixes up the
handling for multiple device instances in a single interconnect target
module that has caused trouble earlier. A custom wrapper driver has been
needed earlier for such cases.
And as the device tree data is organized by the l4 interconnect instances,
we will be able to use genpd later on. This is because each interconnect
instance is also often also a single power domain.
This series of changes has been brewing for several months now. I did not
want to send a pull request earlier as people were still seeing device
specific issues until recently though. However, it turned out that all the
issues were quite trivial to fix. I had missed adding device tree ranges
for the l3 data port used on some devices, and I had missed converting the
device addresses for a few devices. And some devices like needed fixes for
deferred probe handling such as the EHCI PHY for built-in case on omap5.
Anyways, in case of trouble, we can easily just revert changes for a
single device if needed.
* tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Cosmetic fix for omap5 USB node names
ARM: dts: Fix wrong address for omap5 sata phy
ARM: dts: Add missing ranges for dra7 mcasp l3 ports
ARM: dts: Fix ranges for am335x epwmss
ARM: dts: Fix hsi gdd range for omap4
ARM: dts: Add am335x mcasp with l3 data port ranges
ARM: dts: Add missing ranges for am437x mcasp l3 ports
ARM: dts: dra7: Move the ti,no-idle quirk on proper gmac node
ARM: dts: Revert am335x mcasp ti-sysc changes
ARM: dts: omap5: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: Use dra7 mcasp compatible for mcasp instances
ARM: dts: dra7: Move l4 child devices to probe them with ti-sysc
ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am437x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am437x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: dra7: convert to use new clkctrl layout
ARM: dts: am43xx: convert to use new clkctrl layout
ARM: dts: am33xx: convert to use new clkctrl layout
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the Bluetooth node, and the underlying UART node if it's
missing, to the board device tree file for several boards. The LPO clock
is also added to the WiFi side's power sequencing node if it's missing,
to correctly represent the shared connections. There is also a PCM
connection for Bluetooth, but this is not covered in this patch.
These boards all have a WiFi+BT module from AMPAK, which contains one or
two Broadcom chips, depending on the model. The older AP6210 contains
two, while the newer AP6212 and AP6330 contain just one, as they use
two-in-one combo chips.
The Bluetooth side of the module is always connected to a UART on the
same pingroup as the SDIO pins for the WiFi side, in a 4 wire
configuration. Power to the VBAT and VDDIO pins are provided either by
the PMIC, using one or several of its regulator outputs, or other fixed
regulators on the board. The VBAT and VDDIO pins are shared with the
WiFi side, which would correspond to vmmc-supply and vqmmc-supply in the
mmc host node. A clock output from the SoC or the external X-Powers RTC
provides the LPO low power clock at 32.768 kHz.
All the boards covered in this patch are ones that do not require extra
changes to the SoC's dtsi file. For the remaining boards that I have
worked on, properties or device nodes for the LPO clock's source are
missing.
For the Cubietruck, the LPO clock is fed from CLK_OUT_A, which needs to
be muxed on pin PI12. This can be represented in multiple ways. This
patch puts the pinctrl property in the pin controller node. This is due
to limitations in Linux, where pinmux settings, even the same one, can
not be shared by multiple devices. Thus we cannot put it in both the
WiFi and Bluetooth device nodes. Putting it the CCU node is another
option, but Linux's CCU driver does not handle pinctrl. Also the pin
controller is guaranteed to be initialized after the CCU, when clocks
are available. And any other devices that use muxed pins are guaranteed
to be initialized after the pin controller. Thus having the CLK_OUT_A
pinmux reference be in the pin controller node is a good choice without
having to deal with implementation issues.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The clock and reset bindings are going through different trees, and while
the patch doesn't contain any value defined in that header, it still
includes those files and result in a build breakage when building the DT
without the matching clock and reset patches applied.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
We will move the FSL QSPI driver to the SPI framework soon. To
prepare and to make sure the full buswidth is used (as it is with
the current driver), let's add the right properties.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current driver does not use the reg properties, but we will
add a new driver soon. To make sure we have a consistent scheme,
let's fix the reg properties here.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The properties 'bus-num', 'fsl,spi-num-chipselects' and
'fsl,spi-flash-chipselects' were never read by the driver
and can be removed.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With wlcore supporting optional wakeirqs, we can configure it
for droid 4. This makes ssh connection usable with the SoC
entering deeper idle states.
Let's configure a wakeirq both for the wlcore GPIO and the SDIO
dat1 pin in case wlcore starts supporting SDIO dat1 interrupt at
some point.
And let's also add the missing keep-power-in-suspend while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With wlcore supporting optional wakeirqs, we can configure it
for pandaboard. This makes ssh connection usable with the SoC
entering deeper idle states.
Note that pandaboard already has a wakeirq configured for SDIO
dat1 pin although that is not currently used by wlcore.
Signed-off-by: Tony Lindgren <tony@atomide.com>
With wlcore supporting optional wakeirqs, let's configure it for
omap3-evm and update the related pin muxing as some pins are left
unmuxed.
Let's configure a wakeirq both for the wlcore GPIO and the SDIO
dat1 pin in case wlcore starts supporting SDIO dat1 interrupt at
some point.
Note that for off-mode, the wlcore reset GPIO will have a glitch
meaning wlcore will reset. The only way to workaround for this
currently is to configure the reset pin with SAFE_MODE + PULL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The assigned parent clocks should be normally specified in the consumer
device's DT node, this ensures respective driver always sees correct clock
settings when required.
This patch fixes regression in audio subsystem on Odroid XU3/XU4 boards
that appeared after commits:
commit 647d04f8e0 ("ASoC: samsung: i2s: Ensure the RCLK rate is properly determined")
commit 995e73e55f ("ASoC: samsung: i2s: Fix rclk_srcrate handling")
commit 48279c53fd ("ASoC: samsung: i2s: Prevent external abort on exynos5433 I2S1 access")
Without this patch the driver gets wrong clock as the I2S function clock
(op_clk) in probe() and effectively the clock which is finally assigned
from DT is not being enabled/disabled in the runtime resume/suspend ops.
Without the above listed commits the EXYNOS_I2S_BUS clock was always set
as parent of CLK_I2S_RCLK_SRC regardless of DT settings so there was no issue
with not enabled EXYNOS_SCLK_I2S.
Cc: <stable@vger.kernel.org> # 4.17.x
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
While updating cooling maps, the exynos4412-prime.dtsi was left
untouched. This is not a problem with Odroid U3 because it uses its own
map with fan (which was updated). However the cooling maps of Odroid X2
rely only on exynos4412-prime.dtsi.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
These should be now using offset from the module base and not the
full physical address.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.
By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Looks like I missed converting the omap5 sata phy addresses to use offset
from the module base instead of full physical address.
While at it, we can also more it to be a direct child of the interconnect
target module, it is not really a child of the ocp2scp control device.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
-----BEGIN PGP SIGNATURE-----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=mhE2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few device fixes for omaps
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
* tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix the erroneous partition table on D-Link DIR-685
- Multiplex flash usage with other usage using pin control
handling (merged to the MTD tree)
- Use the RedBoot partition parser on SQ201
- Add the USB blocks (DT bindings merged in the last merge
window)
- Bump the debounce times a bit to avoid bouncing
-----BEGIN PGP SIGNATURE-----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=LrYy
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.21:
- Fix the erroneous partition table on D-Link DIR-685
- Multiplex flash usage with other usage using pin control
handling (merged to the MTD tree)
- Use the RedBoot partition parser on SQ201
- Add the USB blocks (DT bindings merged in the last merge
window)
- Bump the debounce times a bit to avoid bouncing
* tag 'gemini-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Bump Gemini platforms to use 100ms debounce
ARM: dts: Add the FOTG210 USB host to Gemini boards
ARM: dts: Fix up SQ201 flash access
ARM: dts: Enable Gemini flash access
ARM: dts: Fix up the D-Link DIR-685 MTD partition info
Signed-off-by: Olof Johansson <olof@lixom.net>
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqJJwAKCRDj7w1vZxhR
xTq4AP9SxrPeKDTBD4mKV+PVuJ2qq919M6o+mcxDkCecEMfbagD+JLkt2uGzdpb8
eC6CuieHvJq1y/akfDpRBf0ZZD0/bw0=
=yRd0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.21
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>
timer and emmc pins) from its first real-world user.
RK3188 improvements (OPPv2, cpu node updates) to prepare for a new
devicetree, the BQ Edison 2 Quad-Core.
VPU device node for rk3288, right now only the jpeg encoder part
will be in the kernel but hopefully other codecs will follow.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlwQw64QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgRFJB/0WHQQtzWXEtFYxgaoWFAgkK8/Lq2LxDBTa
aMx+slPBqMEpLOP3jfxHRy4C+dL2GX2LgaHPJN1ImwSEjUAfPsfO47LNUBl4w0Sx
t2ulAX/TC4wz5Wa78NsGxaszHgpxmDTYeO7ue1nYJ13YlJZ2MIp/Nr9903rWve6h
hPSzkUVe4Vuiz+KLXchzkRWS13zVhy0t9FyPyhJqzZ4ESDhS74g6cm6wuUB0XHXS
EHvhSvgdMa8x1/2flEIXGUAScAWydiglZcraNr3LmrN6dG8PS/IhbGsxp5KCzMTZ
DAGR47tpbXQ1N5HZEqk30yiYMDN/cNeeo2wF9nR9Df//Bj/AwnI6
=A+kY
-----END PGP SIGNATURE-----
Merge tag 'v4.21-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
RV1108 improvements (uart-dma, clocks, interrupt numbers, gmac support
timer and emmc pins) from its first real-world user.
RK3188 improvements (OPPv2, cpu node updates) to prepare for a new
devicetree, the BQ Edison 2 Quad-Core.
VPU device node for rk3288, right now only the jpeg encoder part
will be in the kernel but hopefully other codecs will follow.
* tag 'v4.21-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add internal timer support for rv1108
ARM: dts: rockchip: add BQ Edison 2 QC devicetree
ARM: dts: rockchip: add VPU device node for RK3288
ARM: dts: rockchip: update cpu supplies on rk3188
ARM: dts: rockchip: add phandles to secondary cpu cores
ARM: dts: rockchip: add cpu-core resets for rk3188
ARM: dts: rockchip: convert rk3188 to opp-v2
ARM: dts: rockchip: add #sound-dai-cells to Cortex-A9 i2s
ARM: dts: rockchip: Add UART DMA support for rv1108
ARM: dts: rockchip: Assign the proper GPIO clocks for rv1108
ARM: dts: rockchip: Fix the PMU interrupt number for rv1108
ARM: dts: rockchip: Pass the 'arm,cpu-registers-not-fw-configured' property on rv1108
ARM: dts: rockchip: Pass the 'clock-latency' property on rv1108
ARM: dts: rockchip: Add rv1108 GMAC support
ARM: dts: rockchip: add rv1108 eMMC pin settings
Signed-off-by: Olof Johansson <olof@lixom.net>
- Switch most platforms to the new clock binding
- Small improvement for Axentia nattis
-----BEGIN PGP SIGNATURE-----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=l4zB
-----END PGP SIGNATURE-----
Merge tag 'at91-4.21-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into next/dt
AT91 DT for 4.21
- Switch most platforms to the new clock binding
- Small improvement for Axentia nattis
* tag 'at91-4.21-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: nattis: initialize the BLON pin as output-low early
ARM: dts: at91: at91sam9rl: switch to new clock bindings
ARM: dts: at91: at91sam9x5: switch to new clock bindings
ARM: dts: at91: at91sam9263: switch to new clock bindings
ARM: dts: at91: at91sam9261: switch to new clock bindings
ARM: dts: at91: at91sam9260: switch to new clock bindings
ARM: dts: at91: sama5d2: switch to new clock binding
ARM: dts: at91: sama5d4: switch to new clock bindings
ARM: dts: at91: sama5d2: use the divided clock for SMC
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights
- add CPU OPP tables
- timers: add global timer and TWD
-----BEGIN PGP SIGNATURE-----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=qoPa
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
ARM: dts: Amlogic updates for v4.21, round 2
Highlights
- add CPU OPP tables
- timers: add global timer and TWD
* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: meson8b: add the CPU OPP tables
ARM: dts: meson: meson8: add the CPU OPP table
ARM: dts: meson8b: add the Cortex-A5 global timer
ARM: dts: meson8b: add the ARM TWD timer
ARM: dts: meson8: add the Cortex-A9 global timer
ARM: dts: meson8: add the ARM TWD timer
ARM: dts: meson: group the Cortex-A5 / Cortex-A9 peripherals
dt-bindings: clock: meson8b: export the CPU post dividers
Signed-off-by: Olof Johansson <olof@lixom.net>
- It includes the initial device tree for i.MX7ULP SoC and EVK board
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDd7aAAoJEFBXWFqHsHzOgNEIAKc4dqYzWmfJTMnJGO+Bb1Rc
BPkENpRWk6rWVBuxXwN4MTupXIgj96bBHWsg3kplgcthMRAl2wgomHTpNWXk8R9m
Fn6sH9yIoeqr+xs6BzzQ8COrFBXg8CEZgKLgy+9nhfFi3xNf6pN6IQLgqrGF17MC
zFH+sM0rqlh1l3BfHXMuwHvbhw+ms6Qo6z68OGSXmu0bUPThm2FV/Akivqp+INSI
CeFyZ8RMTkEKVSkFEryZaprKgqlIYW2Kl54yeALjvG03mtn1onaZKqsNV7YonYMC
X+mZPLnwjBUnLi2HbKrStmTR0ePQjg5x1tMT+Eco7Cjj4h6H6uBu0IYMi4PiN7o=
=aOId
-----END PGP SIGNATURE-----
Merge tag 'imx7ulp-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX7ULP device tree for 4.21:
- It includes the initial device tree for i.MX7ULP SoC and EVK board
support.
* tag 'imx7ulp-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: add imx7ulp evk support
ARM: dts: imx: add common imx7ulp dtsi support
dt-bindings: fsl: add imx7ulp pm related components bindings
dt-bindings: fsl: add compatible for imx7ulp evk
clk: imx: add imx7ulp clk driver
clk: imx: implement new clk_hw based APIs
clk: imx: make mux parent strings const
dt-bindings: clock: add imx7ulp clock binding doc
clk: imx: add imx7ulp composite clk support
clk: imx: add pfdv2 support
clk: imx: add pllv4 support
clk: fractional-divider: add CLK_FRAC_DIVIDER_ZERO_BASED flag support
clk: imx: add gatable clock divider support
Signed-off-by: Olof Johansson <olof@lixom.net>
- It contains a series from Otavio Salvador that improves i.MX7D PICO
SoM, and then adds Hobbit baseboard support on top of the improvement.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDdI8AAoJEFBXWFqHsHzOqHoIAKr/bHhIQC1E57/tgaKASelW
lFurkvfm9z0umfl+QW/PMvZF6DQ7IlDN3UuNhTHnqgIiFR3YO9GVX8j/+tmoUjr/
oZeAQzkfffOGT5MXUfd7j7jX9y/nhnsE8AczQjkLt6LDLoRIrD5Tmgo4ka/aZDHB
qj6at43cuHVea/36ZdO7dwH1zHpOQqyKRHoD1W+LNkfLIPkcMAt9UljhfjI2sJ/4
f8RUxIYPXsWr2/DmbFNamUM34dPRmeO8++ZGj07OY8pVszsEis8VYxQEs85BaKoD
YAqb0pl06gGK0b3A/JTWbo6iHx1QRIyiOCOGc7Nnx5PZi6Ad44XA3IbBHi7uh1s=
=av9W
-----END PGP SIGNATURE-----
Merge tag 'imx7d-pico-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX7D PICO boards update for 4.21:
- It contains a series from Otavio Salvador that improves i.MX7D PICO
SoM, and then adds Hobbit baseboard support on top of the improvement.
* tag 'imx7d-pico-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-pico: Add the imx7d-pico-hobbit variant
ARM: dts: imx7d-pico-pi: Extend peripherals support
ARM: dts: imx7d-pico: Extend peripherals support
ARM: dts: imx7d-pico: Improve WiFi regulator name
ARM: dts: imx7d-pico: Pass the Ethernet PHY reset GPIO
ARM: dts: imx7d-pico: Pass the USBOTG1_PWR pinctrl
ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi
ARM: dts: imx7d-pico: Switch to SPDX identifier
ARM: dts: imx7d-pico: Do not harcode the memory size
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards support: emtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
and vf610 based Liebherr's BK4 device, ZII SCU4 AIB board.
- Add flexcan support for i.MX6UL SoC, turn on stop mode wakeup feature
for flexcan, and enable devices on a few i.MX6 NXP boards.
- Enable AUO G101EVN010 lcd panel and Goodix touch support for
imx6ul-ccimx6ulsbcpro board.
- Enable sensors support for imx6qdl-sabresd board: egalax touch, light,
magnetometer and accelerometer sensor.
- Switch more boards to use SPDX identifier.
- Fix memory node duplication in i.MX device tree sources.
- Correct GIC PPI interrupts mask for i.MX6UL and i.MX7 SoCs.
- Drop 'snps,dw-pcie' compatible from LS1021A PCIe device to avoid
incorrect device matching.
- Add the gpu nodes for the adreno 200 GPU on iMX51 and iMX53, which
are now supported by the freedreno driver.
- Add DCP device support for i.MX6ULL, which requires explicit clock
enabling.
- Add '#thermal-sensor-cells' for thermal device and '#cooling-cells'
for cooling devices.
- Add missing clock information for EPIT on i.MX25 SoC.
- Add PWM and qdma devices for LS1021A SoC.
- Update cooling maps of LS1021A SoC to include all devices affected by
individual trip points.
- Random device addition and cleanup on various boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDcmeAAoJEFBXWFqHsHzO9uIH/2e87ayMkmIugUt57aJUOWRG
pbNZZQXHsupVVu0VtYnKp3XBuhMXzvbhhihn9x9pyV+EJ2V4dgtU6gS2EDH2G9pl
TCJItVDOZgllamIg2/McVkuQLsH8tEybud4wlWve96eP22mn6CyCPiDtmdvKYigA
QQEFeSI8YgG1VLbXmhmox0HcowOm2C8asw8sSuo15Y2tWjAcCzKK0p3izRJQhSWn
G/uAUwQQB7e2zrTXfTiJpMWEt664C0tqlhZLlfaPpvmufIbDcpbLHp7mK3iW0rZA
Pjr1uT00rpnRkPkLvtT6tKTi2KviCwua1R58aUXW3ju1Fw6DJC1vSuPyNClCuyk=
=dGG8
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.21:
- New boards support: emtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
and vf610 based Liebherr's BK4 device, ZII SCU4 AIB board.
- Add flexcan support for i.MX6UL SoC, turn on stop mode wakeup feature
for flexcan, and enable devices on a few i.MX6 NXP boards.
- Enable AUO G101EVN010 lcd panel and Goodix touch support for
imx6ul-ccimx6ulsbcpro board.
- Enable sensors support for imx6qdl-sabresd board: egalax touch, light,
magnetometer and accelerometer sensor.
- Switch more boards to use SPDX identifier.
- Fix memory node duplication in i.MX device tree sources.
- Correct GIC PPI interrupts mask for i.MX6UL and i.MX7 SoCs.
- Drop 'snps,dw-pcie' compatible from LS1021A PCIe device to avoid
incorrect device matching.
- Add the gpu nodes for the adreno 200 GPU on iMX51 and iMX53, which
are now supported by the freedreno driver.
- Add DCP device support for i.MX6ULL, which requires explicit clock
enabling.
- Add '#thermal-sensor-cells' for thermal device and '#cooling-cells'
for cooling devices.
- Add missing clock information for EPIT on i.MX25 SoC.
- Add PWM and qdma devices for LS1021A SoC.
- Update cooling maps of LS1021A SoC to include all devices affected by
individual trip points.
- Random device addition and cleanup on various boards.
* tag 'imx-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (82 commits)
ARM: dts: imx51-zii-rdu1: Do not specify "power-gpio" for hpa1
ARM: dts: imx6ul: Remove extra space between node name and brace
ARM: dts: imx6qdl-sabresd: Use GPIO_ACTIVE_HIGH for regulators
ARM: dts: imx6ul: add flexcan support
ARM: dts: imx5: add gpu nodes
ARM: dts: imx6qdl-sabresd: add accelerometer sensor support
ARM: dts: imx6qdl-sabresd: add magnetometer sensor support
ARM: dts: imx6qdl-sabresd: add light sensor support
ARM: dts: imx6qdl-sabresd: Move regulators outside of "simple-bus"
ARM: dts: imx6qdl: Fix memory node duplication
ARM: dts: imx6dl-mamoj: Add a memory node
ARM: dts: imx53-voipac-dmm-668: Fix memory node duplication
ARM: dts: vf610-zii-scu4-aib: Add HI8435 support
ARM: dts: imx6qdl-sabresd: add egalax touch screen support on i2c2 bus
ARM: dts: imx7s: Add flexcan stop mode wakeup support
ARM: dts: imx6ul: Add flexcan stop mode wakeup support
ARM: dts: imx6qdl: Add flexcan stop mode wakeup support
ARM: dts: imx6sx: Add flexcan stop mode wakeup support
ARM: dts: imx6ul-pico: Add the imx6ul-pico-pi variant
ARM: dts: imx6ul-pico-hobbit: Extend peripherals support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add missing properties and nodes for PMIC clocks in multiple DTS
files.
2. Add UHS-I bus speed support to Odroid XU3/XU4/HC SD card and bump the
maximum clock frequency to 200 MHz for SD and eMMC.
3. Update cooling maps to include all CPU devices in multiple DTS files.
4. Enable quirks for Exynos3250 DWC.
5. Add JPEG CODEC node to S5Pv210.
6. Add opp-suspend to devfreq OPPs on Exynos4 boards to fix resuming
from suspend to RAM.
7. Remove eDP from Arndale board as it does not work and breaks also
DSI.
-----BEGIN PGP SIGNATURE-----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=nycP
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.21
1. Add missing properties and nodes for PMIC clocks in multiple DTS
files.
2. Add UHS-I bus speed support to Odroid XU3/XU4/HC SD card and bump the
maximum clock frequency to 200 MHz for SD and eMMC.
3. Update cooling maps to include all CPU devices in multiple DTS files.
4. Enable quirks for Exynos3250 DWC.
5. Add JPEG CODEC node to S5Pv210.
6. Add opp-suspend to devfreq OPPs on Exynos4 boards to fix resuming
from suspend to RAM.
7. Remove eDP from Arndale board as it does not work and breaks also
DSI.
* tag 'samsung-dt-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a quite big pull request this time, with a huge number of changes
(and patches) due to us fixing the vast majority of the DTC warnings our DT
had.
We also have a bunch of other good, more meaningful, changes:
- Support for the new Allwinner T3 (rebranded R40) and f1c100s (armv5)
SoCs
- AXP803 PMIC AC Power supply support
- Rework of the oscillators tree
- Two new boards: the t3-cqa3t-bv3 and Lichee Pi Nano
Plus a few enhancements here and there.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqFhwAKCRDj7w1vZxhR
xcQzAQDJu0dPrs3SQlWdDhOa0iFVp/7gmN4iRMxMScIIjrRUgAEAzmhUjQNNTNLc
OPF9XzMdT12rs2SAbk2XXtWH1hN8KQA=
=vSCG
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21
This is a quite big pull request this time, with a huge number of changes
(and patches) due to us fixing the vast majority of the DTC warnings our DT
had.
We also have a bunch of other good, more meaningful, changes:
- Support for the new Allwinner T3 (rebranded R40) and f1c100s (armv5)
SoCs
- AXP803 PMIC AC Power supply support
- Rework of the oscillators tree
- Two new boards: the t3-cqa3t-bv3 and Lichee Pi Nano
Plus a few enhancements here and there.
* tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (84 commits)
ARM: dts: sunxi: Fix PMU compatible strings
ARM: dts: sun8i: r40: Add RTC device node
ARM: dts: sunxi: h3/h5: Fix up RTC device node and clock references
ARM: dts: sun8i: a23/a33: Fix up RTC device node
ARM: dts: sun8i: r40: Add clock accuracy for external oscillators
ARM: dts: sunxi: h3/h5: Add clock accuracy for external oscillators
ARM: dts: sun8i: a33: Drop audio codec oversampling rate to 128 fs
ARM: dts: sun8i: h3: Remove unnecessary reserved memory node
ARM: dts: sun8i: a33: Remove unnecessary reserved memory node
ARM: dts: suniv: Add device tree for Lichee Pi Nano
ARM: dts: suniv: add initial DTSI file for F1C100s
ARM: dts: axp81x: add AC power supply subnode
ARM: dts: sun8i: v3s: Remove skeleton and memory to avoid warnings
ARM: dts: sun8i: v3s: Provide default muxing for relevant controllers
ARM: dts: sun8i: v3s: Change pinctrl nodes to avoid warning
ARM: dts: sun8i: v3s: Change LRADC node names to avoid warnings
ARM: dts: sun8i: h3: Remove leading zeros from unit-addresses
ARM: dts: sun8i: BPI-M2M: Remove i2c nodes
ARM: dts: sun8i: a23/a33: Provide default muxing for relevant controllers
ARM: dts: sunxi: reference: Move the muxing back to the common DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the internal timer peripheral on RV1108.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These changes add the external memory controller on Tegra20 as well as
the VIC on Tegra124.
-----BEGIN PGP SIGNATURE-----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=UkRy
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.21-rc1
These changes add the external memory controller on Tegra20 as well as
the VIC on Tegra124.
* tag 'tegra-for-4.21-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add VIC on Tegra124
ARM: dts: tegra20: Add clock entry to External Memory Controller
ARM: dts: tegra20: Add interrupt entry to External Memory Controller
Signed-off-by: Olof Johansson <olof@lixom.net>
- New machine: Facebook Backpack-CMM BMC and flash layout
- OpenPower reference systems (Palmetto P8, Romulus P9) move to the
ColdFire based FSI driver
- Misc device tree updates from the OpenBMC project
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+nHMAt9PCBDH63wBa3ZZB4FHcJ4FAlwHEbsACgkQa3ZZB4FH
cJ5WVw//aro9aO6fZqk2l7TA8Umhfa/vyX+w6ShCHjsIjKnhcJo3FxeoVUoe+BdR
cRLAorHY5M6WopxaG9TxfFvRNyaHsHIkyBWXEfKlSSnQV8YeLUTxwZ0v/O2kWNvy
levZ42D+cZJclQvvFwTKXHut5BKsvx9M6wEhapOIIENC1bxHVCbVuXB+cWxGz0zQ
CXkLw3QDaErSlCZzNMd2qgJP4IISqbNk1N0jMzKuO9NBwTpl4ZSZJrNT/jLOed2s
pLF6xmk/ldzVRLj+2T5PE35d7yhpzJyNWvKHzY2Ip8PK3qtf5m5OTzfZGi/aOn2N
rK2DSbAV1zZf6iM8rZbJvGo9FDCwLEGfu3/tZLqDcT9LrWvsEQJINA5oirHGRIaK
Th0eaG1tOPIcAvDhMKdhIL4P8nCRLXgIq9LbaXshmpgRhPtK8yIQhvYBI6ADt+aw
aLOo3aEpWZnrchWDBLFdd5awzEATUQmx6pda1D0MNFKeAu9nbVHNtTaVoAOveqyv
lkuc2pNghMSw4lVCarmrfSd47tkEA7P/cYUIQ8IuNix8PUFF/LsebWkZYOloghdV
GhLSdy0eRl6Bi67g6/XPUhzC3VwMvGBd3+IUpbZ0QG0eKI0c5lrGvr11++hVx2iZ
HfORQhjUHx7CRthhuKofZKM2yg+ov3JT1B7/9Py5crWl+WABiao=
=A+J2
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.21-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
ASPEED device tree updates for 4.20
- New machine: Facebook Backpack-CMM BMC and flash layout
- OpenPower reference systems (Palmetto P8, Romulus P9) move to the
ColdFire based FSI driver
- Misc device tree updates from the OpenBMC project
* tag 'aspeed-4.21-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add Facebook Backpack-CMM BMC
ARM: dts: Add Facebook BMC flash layout
ARM: dts: aspeed: wspoon: Enable iio-hwmon battery
ARM: dts: aspeed: romulus: Enable iio-hwmon-battery
ARM: dts: aspeed: Enable VHUB on Romulus
ARM: dts: aspeed-palmetto: Add LPC control node
ARM: dts: aspeed: Palmetto system can use coprocessor for FSI
ARM: dts: aspeed: Romulus system can use coprocessor for FSI
Signed-off-by: Olof Johansson <olof@lixom.net>
- various fixes from Daniel (W=12 issues mainly)
- support for the first pxa3xx devicetree pxa board
-----BEGIN PGP SIGNATURE-----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=HZqo
-----END PGP SIGNATURE-----
Merge tag 'pxa-dt-4.21' of https://github.com/rjarzmik/linux into next/dt
This device-tree pxa update brings :
- various fixes from Daniel (W=12 issues mainly)
- support for the first pxa3xx devicetree pxa board
* tag 'pxa-dt-4.21' of https://github.com/rjarzmik/linux:
ARM: dts: pxa3xx: Add Raumfeld DTS files
ARM: dts: pxa: clean up USB controller nodes
ARM: dts: pxa3xx: clean up pxa3xx clock controller node name
ARM: dts: pxa3xx: order timer and gcu nodes under /pxabus
ARM: dts: pxa2xx: fix hwuart memory range
ARM: dts: pxa3xx: drop #address-cells and #size-cells from pinctrl node
ARM: dts: pxa2xx: drop #address-cells and #size-cells from /cpus
ARM: dts: pxa3xx: add gcu node
Signed-off-by: Olof Johansson <olof@lixom.net>
We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma. And we're also missing the optional clocks
that we have tagged with HWMOD_OPT_CLKS_NEEDED in omap_hwmod_7xx_data.c.
Note that for reading the module revision register HWMOD_OPT_CLKS_NEEDED
do not seem to be needed. So they could be probably directly managed
only by the mcasp driver, and then we could leave them out for the
interconnect target module.
Fixes: 4ed0dfe3cf ("ARM: dts: dra7: Move l4 child devices to probe
them with ti-sysc")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like I missed the ranges for am335x epwmss. Let's set it up the
same way as for am437x and dra7.
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe
them with ti-sysc")
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add MIO-DMAC (Media IO DMA Controller) nodes, and use them as
the DMA engine of SD/eMMC controllers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
While reviewing the missing mcasp ranges I noticed omap4 hsi range
for gdd is wrong so let's fix it.
I'm not aware of any omap4 devices in mainline kernel though that use
hsi though.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NXP i.MX 7ULP Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MX 7ULP, which features NXP's advanced implementation
of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and
2D Graphics Processing Units (GPUs).
The EVK enables HDMI output for simple out-of-the-box to bring up but
allows reconfiguration for MIPI displays. The EVK is designed as a
System-On-Module(SOM) board that connects to an associated baseboard.
The SOM provides 1 GB LPDDR3, 8 MB Quad SPI flash, Micro SD 3.0 card
socket, WiFi/ Bluetooth capability, USB 2.0 OTG with Type C connector
and an NXP PF1550 power management IC (PMIC). The baseboard provides
additional capabilities including a full SD/MMC 3.0 card socket, audio
codec, multiple sensors, an HDMI connector, and an alternate MIPI display
connector. Additionally, the EVK facilitates software development with the
ultimate goal of faster time to market through the support of both
Linux OS and AndroidTM rich operating systems, as well as FreeRTOS.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
FEC
SD/MMC
See more board details:
https://www.nxp.com/products/processors-and-microcontrollers/
arm-based-processors-and-mcus/i.mx-applications-processors/
i.mx-7-processors/evaluation-kit-for-the-i.mx-7ulp-applications
-processor:MCIMX7ULP-EVK
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7ULP family of processors features NXP's advanced implementation
of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and 2D
Graphics Processing Units (GPUs).
This patch aims to add the initial support including:
1) CLK
2) GPIO PTC, PTD, PTE, PTF
3) uSDHC 1/2
4) LPUART 4/5/6/7
5) LPI2C 6/7
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx7d-pico-hobbit contains a imx7d-pico SoM and a hobbit baseboard.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds following peripherals for the imx7d-pico-pi as:
- LED
- Touchscreen
- GPIO
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are different models of WiFi being used in the SoM and the
handle name was too restrictive. This reworks it to a more generic and
meaningful name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the "phy-reset-gpios" property in order to describe the GPIO
that performs the Ethernet PHY reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-pico-pi board contains:
- One SoM board (imx7d pico)
- One base board (pi).
In order to make it easier for adding support for other board variants,
move the commom SoM part to the imx7d-pico.dtsi file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the memory size described in dts is 2GB, which is incorrect.
There are 512MB and 1GB versions of imx7d-pico boards, so remove
the hardcoded memory size and let the bootloader pass the correct
value to the kernel.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcCTt4AAoJEFBXWFqHsHzOJYkH/A2Y3p+VuWKwW4wDxQI27nlX
w/n5edidmcBDPoI1vzAWNDTECbZXvMABvYP/LCsxmRqGtY9QU9QX8FkvY8q+7VjL
I0LQLzd7sbyTRcJM3ymiclkhzsnAPglI7VQXMdgRqO3wqlyFr7cmkLjnYKNt9nlZ
v+Vtx0UuCqj9Ax4UZoj/067S2SGluMXrAfxGfNUkRmESlo2qYmtNV0MhKtsj4Txh
fDeU6sISp5wHqkF6w+OW5L3gUjXBFwdoOyjYj7a6WREFN9NBkf6Ww1+pby+qd7xx
XlcIkpMtixteSAy714bF4SSRhzxOcgIeY8EeenSCYhoYonyrGn72whIIJnIqxSU=
=HW/5
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.20-3' into imx7d/pico
i.MX fixes for 4.20, round 3:
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
TPA6130A2 SD pin on RDU1 is not really controlled by SoC and instead
is only meant to notify the system that audio was "muted" by external
actors. To accommodate that, drop "power-gpio" property of hpa1 node as
well as specify a name for that GPIO so that userspace can access it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Passing GPIO_ACTIVE_HIGH as GPIO flags for the GPIO controlled
regulator improves the readability, so use it instead of the
hardcoded number.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add flexcan support for i.MX6UL board. Change the place of CAN node delete
due to i.MX6ULZ include i.MX6UL dts but not support flexcan.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the gpu nodes for the adreno 200 GPU on iMX51 and iMX53, now
supported by the freedreno driver.
The compatible for the iMX51 uses a patchid of 1, which is used by drm/msm
driver to identify the smaller 128KiB GMEM size.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add isl29023 light sensor support on i2c3 bus, the light
sensor's power is controlled by a fixed regulator, since
the isl29023 driver and most of other sensors on same
board like mag3110 and mma8451 do NOT support regulator
operation currently, they are all controlled by this
regulator, so this patch also adds the fixed regulator
support and make it always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulators inside "simple-bus", so move
them out to make it cleaner the addition of new regulators.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6qdl have duplicate memory nodes:
- One coming from the board device tree file: memory@
- One coming from the imx6qdl.dtsi file.
Fix the duplication by removing the memory node from
the imx6qdl.dtsi file and by adding 'device_type = "memory";'
in the board Device Tree.
Converted using the following command:
perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"``
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a memory node, with an empty memory size, which will be filled
by the bootloader.
This is done in preparation for removing the memory node from
imx6qdl.dtsi.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the vf610-zii-scu4-aib board there is a hi8435 (32-channel
discrete-to-digital SPI sensor device) in the DSPI0 bus.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add egalax touch screen support on i2c2 bus, it is connected
to LVDS0, while the existing one on i2c3 bus is connected to
LVDS1.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6ul-pico-pi contains a imx6ul-pico SoM and a pi baseboard:
https://www.technexion.com/products/pico-baseboards/detail/PICO-PI
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the same child led node and label name as used in the
imx7d-pico-hobbit board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-pico-hobbit board contains:
- One SoM board (imx6ul pico)
- One base board (hobbit).
In order to make it easier for adding support for other board variants,
move the commom SoM part to the imx6ul-pico.dtsi file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
add the qDMA device tree nodes for LS1021A devices.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on vf500/vf600 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the vf500.dtsi/vf610m4.dtsi files.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.
i.MX7S contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".
Likewise, i.MX7D contains two Cortex-A7 cores, so it should use
"GIC_CPU_MASK_SIMPLE(2)" instead.
Tested on a imx7s-warp.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.
i.MX6UL contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".
Tested on a imx6ul-evk.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The flexcan1 is pin conflict with fec. User would make flexcan1 enabled
with fec disabled to use CAN.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CAN transceiver on MX6SX Sabreauto board seems in sleep mode by default
after power up the board. User has to press the wakeup key on ARD baseboard
before using the transceiver, or it may not work properly when power up the
board at the first time(warm reset does not have such issue).
This patch operates the wake pin too besides stby/en pins by chaining them
together in regulator mode.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CAN transceiver is different on RevA and RevB board.
It's active high on RevA while active low on Rev B.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1021A has 8 possible PWMs, so adding them (disabled by default)
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
connected on the LVDS interface through an on-board LVDS transceiver.
This change adds support for the touch interface.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This change adds support for the AUO G101EVN010 lcdif panel for the
mxsfb DRM driver.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx25 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx25.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx27 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx27.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx1 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx1.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx28 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx28.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx23 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx23.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Most of the i.MX NXP reference board dts files have already been
converted, so switch the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Most of the wandboard dts files have already been converted, so switch
the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx50-evk has duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx50.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL EVK board has WDOG_B pin connected to the PMIC;
Add the WDOG_B pinctrl entry and 'fsl,ext-reset-output'
property to wdog node to let watchdog trigger a system
POR reset via the PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, there is a debug LED controlled
by MX6SLL_PAD_EPDC_VCOM1__GPIO2_IO04 pin, add support
for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6qdl-sabreauto boards have a pcie slot so let's enable it.
Tested on imx6dl-sabreauto with an atk9k wifi card; scanning works.
There are unhandled differences for imx6qp but imx6qp-sabreauto.dts
already contains a snippet explicitly disabling the &pcie node so that
can be dealt with later.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6sl have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sl.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6sx have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sx.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx6ul have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6ul.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add memory node to board dts.
This is done in preparation of removing the memory node from imx6ul.dtsi.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Current imx7d-sdb.dts has some incorrect settings about
Rev-A and Rev-B boards, some of the settings are based on
Rev-A board but some are based on Rev-B board, clean up it
by adding i.MX7D SDB Rev-A board support, make default
imx7d-sdb.dts for Rev-B board as usual, and introduce
imx7d-sdb-reva.dts for Rev-A board. Below are the affected
differences of Rev-A and Rev-B board:
Rev-A Rev-B
USB_OTG2_PWR: UART3_CTS_B GPIO1_IO07
ENET_EN_B: None GPIO1_IO04
TP_INT_B: EPDC_DATA13 EPDC_BDR1
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the emtrion GmbH emCON-MX6 modules.
They are available with imx.6 Solo, Dual-Lite, Dual and Quad
equipped with Memory from 512MB to 2GB (configured by U-Boot).
Our default developer-Kit ships with the Avari baseboard and the
EDT ETM0700G0BDH6 Display (imx6[q|dl]-emcon-avari).
The devicetree is split into the common part providing all module
components and the basic support for all SoC versions
(imx6qdl-emcon.dtsi) and parts which are i.mx6 S|DL and D|Q relevant.
Finally the support for the avari baseboard in the developer-kit
configuration is provided by the emcon-avari dts files.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adding the label cpu0 allows the adjustment of cpu-parameters
by reference in overlaying dtsi files in the same way as it
is possible for imx6q devices.
Signed-off-by: Jan Tuerk <jan.tuerk@emtrion.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some SOCs in the i.MX6 family have a USB host controller that is
only capable of the HSIC interface and has no on-board PHY.
To be able to use these controllers, we need to add "usb-nop-xceiv"
dummy PHYs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
From i.MX6SX reference manual CCM chapter, KPP and
WDOGn use IPG clock as their clock, specify IPG
clock for KPP and WDOGn instead of DUMMY clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Removed the wrong compatible string "snps,dw-pcie", in case
match incorrect driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx7 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx7s.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx35 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx35.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx31 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx31.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/media/fsl-pxp.txt,
only one PXP clock needs to be described and it should be named
"axi".
Also pass the compatible string as suggested in the bindings doc.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove "regulator-always-on" property for vddpu regulator
since it can be OFF when GPU power domain is OFF.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "fsl,mf-mix-wakeup-irq" is ONLY used as a temporary
solution in NXP's internal tree for Mega/Fast Mix off
feature after suspend, upstream kernel does NOT need it,
remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx53 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx53.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Boards based on imx51 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx51.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
One small fix for a regulator range on the Banana Pi M3
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAp//QAKCRDj7w1vZxhR
xSwaAP9Yva8hQFjQsLSdxd9qJbMwd0Tr96dI7N8EczzWpi3zYgEA00HNJPfSprXN
pQ6xgaWplftcBbZj6iC24QhY5VDB4wI=
=3MMH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.20
One small fix for a regulator range on the Banana Pi M3
* tag 'sunxi-fixes-for-4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: bananapi-m3: increase vcc-pd voltage to 3.3V
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcCTt4AAoJEFBXWFqHsHzOJYkH/A2Y3p+VuWKwW4wDxQI27nlX
w/n5edidmcBDPoI1vzAWNDTECbZXvMABvYP/LCsxmRqGtY9QU9QX8FkvY8q+7VjL
I0LQLzd7sbyTRcJM3ymiclkhzsnAPglI7VQXMdgRqO3wqlyFr7cmkLjnYKNt9nlZ
v+Vtx0UuCqj9Ax4UZoj/067S2SGluMXrAfxGfNUkRmESlo2qYmtNV0MhKtsj4Txh
fDeU6sISp5wHqkF6w+OW5L3gUjXBFwdoOyjYj7a6WREFN9NBkf6Ww1+pby+qd7xx
XlcIkpMtixteSAy714bF4SSRhzxOcgIeY8EeenSCYhoYonyrGn72whIIJnIqxSU=
=HW/5
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.20, round 3:
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
* tag 'imx-fixes-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
ARM: dts: imx7d-pico: Describe the Wifi clock
Signed-off-by: Olof Johansson <olof@lixom.net>
The 50ms debounce is too low and give ghost bounces on some
platforms. Bump it to 100ms to make it stable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the FOTG210 USB host controller to the Gemini
device trees. In the main SoC DTSI it is flagged as disabled
and then it is selectively enabled on the devices that utilize
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This sets the partition information on the SQ201 to be read
out from the RedBoot partition table, removes the static
partition table and sets our boot options to mount root from
/dev/mtdblock2 where the squashfs+JFFS2 resides.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some Gemini platforms have a parallel NOR flash which conflicts
with use cases reusing some of the flash lines (such as CE1)
for GPIO.
Fix this on the D-Link DIR-685 and Itian SQ201 by creating
"enabled" and "disabled" states for the flash pin control
handle, and rely on the flash handling code to switch this
in and out when accessed so these lines can be used
for GPIO when flash is not accessed, and enable flash
access.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vendor firmware was analyzed to get the right idea about
this flash layout. /proc/mtd contains:
dev: size erasesize name
mtd0: 01e7ff40 00020000 "rootfs"
mtd1: 01f40000 00020000 "upgrade"
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd4: 00040000 00020000 "RedBoot"
mtd5: 00020000 00020000 "LangPack"
mtd6: 02000000 00020000 "flash"
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Remains:
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd5: 00020000 00020000 "LangPack"
Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of
these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is
"rgdb" of 0x40000.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Earlier attempt to move am335x mcasp to probe with ti-sysc
interconnect target module caused audio to stop working and and
the dts changes were reverted by commit 5d2632a577 ("ARM: dts:
Revert am335x mcasp ti-sysc changes").
Turns out we were missing the l3 data port ranges for mcasp. This
caused mcasp dma to attempt to use wrong port address. So let's
try again essentially reverting the earlier revert and adding the
missing l3 data port ranges.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"arm,cortex-a15-pmu" is not a valid fallback compatible string for an
Cortex-A7 PMU, so drop it.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The R40 has an RTC hardware block, which has additional registers
that are not related to RTC or clock functions, and is otherwise
compatible with the H3's RTC.
Add a device node for it, and fix up any references to the LOSC.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the H3 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The H5's RTC has some extra crypto-related registers compared to
the H3. Their exact functions are not clear. Also the RTC-VIO regulator
has different settings.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the A23 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The A33's RTC is the same as the A23.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The register range is also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Arndale boards have wires for DSI and eDP panels, but in-kernel support
for eDP panels is broken for long time and breaks display support even on
boards with DSI panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Edison 2 Quad-Core was a Tablet device released in 2013 by MundoReader
using a rk3188 soc. Add a devicetree for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add the Video Processing Unit node for RK3288 SoC.
Fix the VPU IOMMU node, which was disabled and lacking
its power domain property.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.
In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.
Fixes: 56354959cf ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The R40 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H3 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
The internal oscillator is left unchanged, as it will be removed later.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma.
Fixes: d95adfd458 ("ARM: dts: am437x: Move l4 child devices to
probe them with ti-sysc")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the SPI NOR device used to boot up the system
to the iWave RZ/G1N Qseven System On Module DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The iWave RZ/G1N board is almost identical to RZ/G1M. cmt and rwdt modules
are SoC specific and should be part of board dts rather than SoM dtsi. By
moving these nodes to the common dtsi it allows cmt and rwdt to be enabled
on both of these boards with less lines of code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The current oversampling rate of 512 means that for 48 kHz 16 bit
stereo, the MCLK is running at the same rate as the module clock,
so there is no head room to support higher sampling rates. The codec
however supports up to 192 kHz for playback.
This patch drops the oversampling rate from 512 to 128, so that 192 kHz
audio can be played back directly without downsampling. Ideally we
should be using different oversampling rates for different sampling
rates, but that's not possible without a platform-specific machine
driver.
Fixes: 870f1bd1f5 ("ARM: dts: sun8i: Add audio codec, dai and card for A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Just like on the A33, the video engine on the H3 can map any address in
memory, so there is no particular need to have reserved memory at a fixed
address.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While we believed that the memory for the video engine had to be kept
in the first 256 MiBs of DRAM, this is no longer true starting with the
A33 and any address can be mapped.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMAC driver requires a syscon node to access the EMAC clock
configuration register (that is part of the system-control register
range and controlled). For this purpose, a dummy syscon node was
introduced to let the driver access the register freely.
Recently, the EMAC driver was tuned to get access to the register when
the SRAM driver is registered (as used on the A64). As a result, it is
no longer necessary to have a dummy syscon node for that purpose.
Now that we have a proper system-control node for both the H3 and H5,
we can get rid of that dummy syscon node and have the EMAC driver use
the node corresponding to the proper SRAM driver (by switching the
syscon label over to each dtsi). This way, we no longer have two
separate nodes for the same register space.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike in previous generations, the system-control register range is not
limited to a size of 0x30 on the H3. In particular, the EMAC clock
configuration register (accessed through syscon) is at offset 0x30 in
that range.
Extend the register size to its full range (0x1000) as a result.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c7 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The values are taken from Amlogic's 3.10 kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The values are taken from Amlogic's 3.10 kernel sources. Their sources
have a "meson8m2_n200_2G.dtd" which defines a different voltage table:
- 0.86V for 96MHz
- (values in between omitted)
- 1.14V for 1.992GHz
The reason for this is simply the hardware design because the voltage
regulator on this board is has a minimum output of 0.86V and a maximum
output of 1.14V. The recommended settings are added with this patch
instead of using the values that are only valid for one board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8b SoC is using four Cortex-A5 cores. These come with an ARM
global timer.
This adds the Cortex-A5 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8B SoC is using four ARM Cortex-A5 cores which come with a
"TWD" (Timer-Watchdog) based timer. This adds support for the ARM TWD
Timer on this SoC.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoCs are using four Cortex-A9 cores. These come
with an ARM global timer.
This adds the Cortex-A9 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoC are using four ARM Cortex-A9 cores which
come with a "TWD" (Timer-Watchdog) based timer. This adds support for
the ARM TWD Timer on these two SoCs.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The public Meson8b (S805) datasheet describes a memory region called "A9
Periph base" which starts at 0xC4300000 and ends at 0xC430FFFF. Add a
simple-bus node and move all peripherals that are part of this memory
region.
This makes the .dts a bit easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add a device node for the PCIe controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the xhci controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT node for the QSPI interface to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for the camera daughter board which is
connected to iWave's RZ/G1N Qseven carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add TPU support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for pwm[0123456] to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7744 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN[012] support to SoC dt.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CMT[01] support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch instantiates the thermal sensor module with thermal-zone
support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the r8a7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for can0 and can1 to the r8a7744 SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G1N SoC (a.k.a. R8A7744).
This work is based on similar work done on the R8A7743 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb dmac and hsusb device nodes on RZ/G1N SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe internal PCI bridge devices, USB phy device and
link PCI USB devices to USB phy.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the SDHI0 controller on iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add eMMC support for iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add MMC node to the DT of the r8a7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-5] and IIC[0,1,3] devices nodes to the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF{|A|B} ports in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT node for the Advanced Power Management Unit (APMU), add the
second CPU core, and use "renesas,apmu" as "enable-method".
Also add cpu1 phandle node to the PMU interrupt-affinity property.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Ethernet AVB support for R8A7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe GPIO blocks in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC0/1 in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G1N (R8A7744) SoC. Added placeholders
to avoid compilation error with the common platform code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The thermal hardware description for the RZ/G1M SoC was added to its DTS
after the introduction of support for thermal zones, and included a
thermal-zones node from the beginning.
Hence there is no need to claim compatibility with
"renesas,rcar-thermal", which would be needed only for backwards
compatibility with kernels predating thermal zone support.
Fixes: 6c76b4f7d8 ("ARM: dts: r8a7743: Add thermal device to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lichee Pi Nano is a F1C100s board by Lichee Pi.
Add initial device tree for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
F1C100s is one product with the suniv die, which has a 32MiB co-packaged
DDR1 DRAM chip. As we have the support for suniv pin controller and CCU now, add a
initial DTSI for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds a set of DTS files that support all PXA3xx based Raumfeld
audio hardware devices.
Common nodes are factored out into 'common' and 'tuneable-clock' include
files to keep the top-level DTS files smaller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
[Robert: Reordered Makefile in alphabetical order]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
-----BEGIN PGP SIGNATURE-----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=iFMZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes,
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
* tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.21, please pull the following:
- Rafal relicenses a bunch of DTS files he wrote under the GPL 2.0+/MIT
license and adds proper SPDX license tags in the process
- Rene adds support for the Linksys EA6500 v2 Wi-Fi router based on
BCM4708 plus two BCM4360 and BCM4331 radios
- Phil documents and updates the vchiq mailbox compatible string in
order to establish a correct agreement between the Raspberry Pi
firmware and the ARM CPU's view of what an ARM CPU cache line size is,
he also fixes the mailbox "reg" property to be correctly expressed in
bytes
- Stefan updates the Raspberry Pi Zero DTS files to use SPDX tags
- Florian enables the SATA PHY and AHCI controller on the BCM63138 SoCs,
he also does a bit of refactoring of aliases for the Northstar Plus
DTS files
-----BEGIN PGP SIGNATURE-----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=kE/p
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 4.21, please pull the following:
- Rafal relicenses a bunch of DTS files he wrote under the GPL 2.0+/MIT
license and adds proper SPDX license tags in the process
- Rene adds support for the Linksys EA6500 v2 Wi-Fi router based on
BCM4708 plus two BCM4360 and BCM4331 radios
- Phil documents and updates the vchiq mailbox compatible string in
order to establish a correct agreement between the Raspberry Pi
firmware and the ARM CPU's view of what an ARM CPU cache line size is,
he also fixes the mailbox "reg" property to be correctly expressed in
bytes
- Stefan updates the Raspberry Pi Zero DTS files to use SPDX tags
- Florian enables the SATA PHY and AHCI controller on the BCM63138 SoCs,
he also does a bit of refactoring of aliases for the Northstar Plus
DTS files
* tag 'arm-soc/for-4.21/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Describe Northstar pins mux controller
ARM: dts: BCM5301X: Add basic DT for Linksys EA6500 V2
ARM: dts: bcm2835-rpi-zero: Switch to SPDX identifier
ARM: dts: bcm283x: Correct mailbox register sizes
ARM: dts: bcm283x: Correct vchiq compatible string
dt-bindings: soc: Document "brcm,bcm2836-vchiq"
ARM: dts: NSP: Move aliases to bcm-nsp.dtsi
ARM: dts: BCM53573: Relicense SoC file to the GPL 2.0+ / MIT
ARM: dts: BCM63xx: Enable SATA AHCI and PHY for BCM963138DVT
ARM: dts: BCM63xx: enable SATA PHY and AHCI controller
ARM: dts: BCM53573: Relicense Tenda AC9 file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense BCM47094 file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense BCM47081/BCM4709 files to the GPL 2.0+ / MIT
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
introduced a wifi power sequence. Unfortunately the polarity of the reset
GPIOs were wrong and broke the wifi support on Raspberry Pi 3 B and
later in 3 B+. This wasn't discovered before since the power sequence
takes only effect in case the relevant MMC driver is compiled as a module.
Fixes: b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of Expander")
Cc: stable@vger.kernel.org
Reported-by: Matthias Lueschner <lueschem@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=911443
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Mark as opp-suspend required devfreq Operating Performance Points to
fix resuming issues on Exynos 4 boards.
The patch is based on earlier work by Tobias Jakobi.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Split the 10Kbytes CAN message RAM to be able to use simultaneously
FDCAN1 and FDCAN2 instances.
First 5Kbytes are allocated to FDCAN1 and last 5Kbytes are used for
FDCAN2. To do so, set the offset to 0x1400 in mram-cfg for FDCAN2.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add initial version of device tree file for Facebook Backpack CMM
(Chasis Management Module) ast2500 BMC.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is the layout used by Facebook BMC systems. It describes the fixed
flash layout of a 32MB mtd device.
Signed-off-by: Tao Ren <taoren@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The BMC can read the RTC battery voltage via ADC
channel 12.
Signed-off-by: Matt Spinler <spinler@linux.vnet.ibm.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add iio-hwmon-battery using adc channel 12 and enable adc to make
adc running. This channel is used to read RTC battery voltage.
Note with Romulus hardware design, it requires GPIOR3 to be pulled
high to read the voltage, otherwise the reading is 0.
When GPIOR3 is high, it consumes battery and impacts the battery life.
So it is left for user space to toggle the GPIO when trying to read the
voltage.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This allows userspace to switch away from bitbanging to use kernel
FSI with the coprocessor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This replaces the FSI compatible with the ColdFire FSI compatible.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
PXA25xx SoCs don't have a USB controller, so drop the node from the
common pxa2xx.dtsi base file. Both pxa27x and pxa3xx have a dedicated
node already anyway.
While at it, unify the names for the nodes across all pxa platforms.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Sergey Yanovich <ynvich@gmail.com>
Link: https://patchwork.kernel.org/patch/8375421/
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The clock controller node does not need a unit slave designator as it does
not have a reg property. Also, remove the underscore from the name.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
These are devices on the PXA bus, so make the device tree structure
reflect that.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The memory range for the hwuart is at 0x41600000, not 0x41100000.
This also solves a conflict with the MMC controller node.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The pinctrl node does not have any children, so the #address-cells and #size-cells
properties are not needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
PXA is single-core only, so this node will not have enumerable children.
Drop the #address-cells and #size-cells properties to squelch a dtc warning.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add a device node for hardware graphic acceleration.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Add node for s5p-jpeg codec, which is present in S5PV210 SoC.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The base aspeed-g5.dtsi already defines a '/memory@80000000' node, so
'/memory' in the board files create a duplicate node. We're probably
getting lucky that the bootloader fixes up the memory node that the
kernel ends up using. Add the unit-address so it's merged with the base
node.
Found with DT json-schema checks.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- support more timers on meson8
- add the stdout-path property on several boards
-----BEGIN PGP SIGNATURE-----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=9yK+
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 32-bit DT updates for v4.21
- support more timers on meson8
- add the stdout-path property on several boards
* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: add the clock inputs for the Meson timer
ARM: dts: meson: add the TIMER B/C/D interrupts
ARM: dts: meson: consistently disable pin bias
ARM: dts: meson8b: mxq: add the /chosen/stdout-path property
ARM: dts: meson8: minix-neo-x8: add the /chosen/stdout-path property
ARM: dts: meson6: atv1200: add the /chosen/stdout-path property
dt-bindings: timer: meson6_timer: document the clock inputs
dt-bindings: timer: meson6_timer: document all interrupts
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes mostly configure pinctrl for am437x-gp-evm. There is
also non-critical fix for a comment for Clang, and we enable earlycon
for am3517-evm.
-----BEGIN PGP SIGNATURE-----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=/+sU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.21 merge window
These changes mostly configure pinctrl for am437x-gp-evm. There is
also non-critical fix for a comment for Clang, and we enable earlycon
for am3517-evm.
* tag 'omap-for-v4.21/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-gp-evm: Add sleep state for beeper pins
ARM: dts: am437x-gp-evm: Add pinmux for gpio0 wake
ARM: dts: am437x-gp-evm: Add uart0 pinctrl default and sleep states
ARM: dts: am437x-gp-evm: Add pinctrl for debugss pins
ARM: dts: am437x-gp-evm: Add pinctrl for unused_pins
ARM: dts: am437x-gp-evm: Add state for ddr3 vtt toggle pin
ARM: dts: am3517-evm: Enable earlycon stdout path
ARM: dts: omap3-gta04: Fix comment block
Signed-off-by: Olof Johansson <olof@lixom.net>
This updates the Versatile Express family DTS files to
contain the correct and detailed information required
for the PL11x DRM driver to work properly.
-----BEGIN PGP SIGNATURE-----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=4oHX
-----END PGP SIGNATURE-----
Merge tag 'vexpress-drm-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Versatile Express DTS update for DRM:
This updates the Versatile Express family DTS files to
contain the correct and detailed information required
for the PL11x DRM driver to work properly.
* tag 'vexpress-drm-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Modernize the Vexpress PL111 integration
Signed-off-by: Olof Johansson <olof@lixom.net>
Despite Marvel keeps their base addresses secret there's a good chance
they're actually correct.
SSP1 and SSP3 bases were taken from OLPC 1.75: OpenFirmware and kernel
respectively. SSP2 and SSP4 addresses are from James Cameron who actually
has a copy of the data sheet.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
The USB OTG PHY chip. To be used by the OTG controller.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
I've gotten the base addresses, clocks and interrupts from an rusty and old
out-of-tree driver. I haven't actually checked against the datasheet, since
that one is reserved for the Marvell inner circle.
Tested with an accelerometer on TWSI6 on an OLPC XO 1.75 machine.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:
arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58
I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.
I'm also copying some properties from TWSI1 that were missing or
incorrect.
Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's apparently four of them on a MMP2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
The timer needs the timer clock to be enabled, otherwise it stops
ticking.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will be useful for boards that actually use GPIO pins.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
gpio-pxa uses two cell to encode the interrupt source: the pin number
and the trigger type. Adjust the device node accordingly.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Use SPDX license identifier for all SoCFPGA DTS files.
- Remove dma-mask property as it has been deprecated.
- Use tabs in DTS files.
- Use the specific "altr,stratix10-rst-mgr" property for the Stratix10
reset manager.
-----BEGIN PGP SIGNATURE-----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=IDQS
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v5.0
- Use SPDX license identifier for all SoCFPGA DTS files.
- Remove dma-mask property as it has been deprecated.
- Use tabs in DTS files.
- Use the specific "altr,stratix10-rst-mgr" property for the Stratix10
reset manager.
* tag 'socfpga_dts_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: stratix10: use "altr,stratix10-rst-mgr" binding
ARM: dts: socfpga: use tabs for indentation
arm: dts: socfpga: remove dma-mask property
arm: dts: socfpga*.dts*: use SPDX-License-Identifier
Signed-off-by: Olof Johansson <olof@lixom.net>
regulator name and referencing all cpus in the cooling maps instead
of only cpu0.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlv2mkYQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf2ZCACoJZ1G4trbzqhdH1DXlLac7hsk+Hu/1jTW
WrP6mXVyOJLdo3XRAoYEKI8WFx88pyXUDuXnxH4vO2SaoEDyIDYGuYxiiDZsrMiv
oX0uyx9JKpY3cSBiDsPkfaxdcyGmVP2x10gxJvcoF4mP3FlMh5Ovtoyq83djxm7B
/kw0NniMU9qKn8ilPAy+kiNADQkC3swupq0uLpt4wgvIPKkiGWEEaJjG30boc21q
qpFlB9PowM52ZIqttTjvzh/wnb0eB6sEcI9tuuUa4S8y0PHzRpiIco0pqUsuq6I4
UbAbqshORINRkJTZwhfw4HWmrKLF5s6vXGKFbx9M3TgVHKWGYHTw
=zDNA
-----END PGP SIGNATURE-----
Merge tag 'v4.21-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Powerdomain and QoS nodes for rk3066 and rk3188. A fix for a rock2
regulator name and referencing all cpus in the cooling maps instead
of only cpu0.
* tag 'v4.21-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add all CPUs in cooling maps
ARM: dts: rockchip: Fix rk3288-rock2 vcc_flash name
ARM: dts: rockchip: add rk3066/rk3188 power-domains
ARM: dts: rockchip: add qos nodes found on rk3066 and rk3188
dt-bindings: add power-domain header for RK3066 SoCs
dt-bindings: add power-domain header for RK3188 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
- Reomve non-existing EEPROM device from imx51-zii-rdu1 board.
It was added by mistake.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcAVNxAAoJEFBXWFqHsHzO0SYH/06mGVqrvAdCYYMamrcLPkom
7aVizSIcK6O+9ddxhA5pDSHMIKu0Wjn6d1acySeql6AWg0d9pECydoI7Rgfj/fDC
mw/aXlv9TJv+4R6/2MI/CEO2Xfi0c2d0nCzTAmsL3CKp92hIVqPTxc7mW5K9J8bx
W2wbj1wueCn/cLiynDV25krxq4BRbsU8g0Ke+HiuO89W9Qb87qgPyJjWeecyH/dl
/llXuiFzZqHYpmzdYacnKvKResVCCc8Ev4VgEF89M1M9tgOojQOakFfMBfTDEIHG
iooQLc6WLdYjsqDhmnUEbonZ+pHBbNPUvV0iHmR/9y0SyVZdrGgNWjVRSkKuT6I=
=OlmI
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.20, round 2:
- Reomve non-existing EEPROM device from imx51-zii-rdu1 board.
It was added by mistake.
* tag 'imx-fixes-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of fixes contains minor regression fixes for LogicPD dts files
for MMC pinctrl and interrupts. There is also one section annotation fix
that shows up with Clang, and a fix for an unitialized field for omap1.
-----BEGIN PGP SIGNATURE-----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=EaEX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few minor fixes for omaps for v4.20-rc cycle
This set of fixes contains minor regression fixes for LogicPD dts files
for MMC pinctrl and interrupts. There is also one section annotation fix
that shows up with Clang, and a fix for an unitialized field for omap1.
* tag 'omap-for-v4.20/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: ams-delta: Fix possible use of uninitialized field
ARM: dts: am3517-som: Fix WL127x Wifi interrupt
ARM: dts: logicpd-somlv: Fix interrupt on mmc3_dat1
ARM: dts: LogicPD Torpedo: Fix mmc3_dat1 interrupt
ARM: dts: am3517: Fix pinmuxing for CD on MMC1
ARM: OMAP2+: prm44xx: Fix section annotation on omap44xx_prm_enable_io_wakeup
Signed-off-by: Olof Johansson <olof@lixom.net>
firmware on these devices as issues identifying the formally correct
node.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlv2krMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgenqB/4z/gAlUZ8xo9au7cHLXOKmg7WkhqRkWHsr
F1rib1I8wv2d6X+PkQv6QiejaJcp+Tj4unx6IGx904PADlCRj38uo+7jEgirf3h+
MGUcZM9+A1V1IvN31eaSTax9KO/XUaABxCBiDSH91YM6JZHRTh1oskjC1lt2pmfF
yygoVfX0jA6GC9+S1YpKAmMyY37ZFIyiZFak5qVPzDDIHKqRLgFDDc2gGTlsqTca
glxbHapRHXg624wUcuGgnRmhhrzNPFzrQ89/LAZX9MBAwC8p2SekhzE7VR2nAvvZ
9Asl7SU2lOjYTpWP/b8jONpPIPvDSXKnfYxQSYDD+Eud+kUk+rqU
=wPsf
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Moving the veyron memory node from memory@0 back to memory, as the
firmware on these devices as issues identifying the formally correct
node.
* tag 'v4.20-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Remove @0 from the veyron memory node
Signed-off-by: Olof Johansson <olof@lixom.net>
Single patch to use updated coresight graph bindings thereby removing
loads of dtc warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJboNezAAoJEABBurwxfuKYFB0QAKxuGglCbwo5YitzfrsEKFFK
HRCCl8VdmN9ENGsM+wK3qMED6wLeAaQGpGmIpE5Gn8DYBKKQ0S16nEcMg+9CmmOg
jPrcFqbpliDOkwwblwl/pV1vcaTE4bGs7ZF+7TrHJVxwY/GEgjJn56No0mWrxs9i
wqegu5vc0pky9lFMFlw4/5zwDycRbb8Zxgg3X6sAfoGdhLoCgusXLk4DOy3HyA8n
rz4MsUwQmTw9O1JtMxNSqFfWBJSm6nom7C0z9iS4iISKGIlId0r1z5W83Km5/seW
ChChUzWrKOMY6xYhoexkw5m4vI/RjbNcp5CvO+C6SHkyHWzwvNeHLdP9CMpVavTs
OvRUFyXbozRn4PzvK+oE+vCbKoLO+14VtBIG0UXS5F4ykEg3gMur38v91rhTdCWc
y1VsK5fHid26tJYNwTg5KbT4wOWM4bE6JCaDvibaWFum2RYLwh6WuN+tqV0PDjLM
qovVTABQcMXDTxfEG78GvQF0vb6lpN3CEzFZdjQPmUPJveYxG7g9TQVVNKEdJKjj
9w4AiNub0c3kdVHqwFrmoYj6a8BuA9w7w+MjEISX6mr5tZqxh61ygZwp4p4AyKwt
VLFuXgj+0gEAg60Km8Z2X7PcxySOoX8vjWiiNTdbtAtUsM4m6kX3RrjM/qp1HW1u
FB/pQ3kiwb4Ye0DtyJSK
=8TMG
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
ARMv7 Vexpress updates for v4.20
Single patch to use updated coresight graph bindings thereby removing
loads of dtc warnings
* tag 'vexpress-updates-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress/TC2: Update entries to match latest coresight bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
This describes hardware & will allow referencing pin functions. The
first usage is UART1 which allows supporting devices using it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It is wireless home router based on BCM4708A0 with BCM4360 + BCM4331
wireless chipsets. The BCM4331 5GHz chip currently isn't supported only
due to missing compatible firmware.
Signed-off-by: Rene Kjellerup <rk.katana.steel@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Hwmod parses the DT hierarchically from root to search for matching
ti,hwmod property. With the introduction of L4 data, we have two nodes
with the ti,hwmod = "gmac" declaration, and the hwmod core only matches
the first one found, which is the target-module one. This node incorrectly
dropped the ti,no-idle flag, which causes number of problems, like ignoring
errata i877, and also causing an intermittent boot failure on certain dra7
boards.
Fix the issue by moving the ti,no-idle flag to the proper node.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this McASP FIFO would constantly underflow. EDMA
test via dmatest works though.
Let's revert the change for now until we know the root cause.
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Video Image Compositor can be used to perform a variety of image
operations. Add a device tree node for it, so that it can be exposed
as a host1x channel to userspace.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Versatile Express was submitted with the actual display
bridges unconnected (but defined in the device tree) and
mock "panels" encoded in the device tree node of the PL111
controller.
This doesn't even remotely describe the actual Versatile
Express hardware. Exploit the SiI9022 bridge by connecting
the PL111 pads to it, making it use EDID or fallback values
to drive the monitor.
The also has to use the reserved memory through the
CMA pool rather than by open coding a memory region and
remapping it explicitly in the driver. To achieve this,
a reserved-memory node must exist in the root of the
device tree, so we need to pull that out of the
motherboard .dtsi include files, and push it into each
top-level device tree instead.
We do the same manouver for all the Versatile Express
boards, taking into account the different location of the
video RAM depending on which chip select is used on
each platform.
This plays nicely with the new PL111 DRM driver and
follows the standard ways of assigning bridges and
memory pools for graphics.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Meson Timer IP block has two clock inputs:
- clk81 for using the system clock as timebase
- xtal for a timebase with 1us, 10us, 100us and 1ms resolution
The clocksource driver does not use these yet, but it's still a good
idea to add them as this describes how the hardware actually works
internally.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The timer on Meson6/Meson8/Meson8b SoCs has four internal timer events.
For each of these a separate interrupt exists.
Pass these interrupts to allow using the timers other than TIMER A.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
On Amlogic chipsets, the bias set through pinconf applies to the pad
itself, not only the GPIO function. This means that even when we change
the function of the pad from GPIO to anything else, the bias previously
set still applies.
As we have seen with the eMMC, depending on the bias type and the function,
it may trigger problems.
The underlying issue is that we inherit whatever was left by previous user
of the pad (pinconf, u-boot or the ROM code). As a consequence, the actual
setup we will get is undefined.
There is nothing mentioned in the documentation about pad bias and pinmux
function, however leaving it undefined is not an option.
This change consistently disable the pad bias for every pinmux functions.
It seems to work well, we can only assume that the necessary bias (if any)
is already provided by the pin function itself.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch removes support for the APQ8064 based Arrow SD600 eval
board. This board was never sold publicly and had very limited
distribution. As such, we are removing this board and no longer
going to support it.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
As per upstream discussion [1], we should have an SoC-specific
compatible string for Qualcomm's SDHCI nodes. Let's add it.
[1] https://lkml.kernel.org/r/20181105203657.GA32282@bogus
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch correctly sets the gpios property for the ak8963
magnetometer's DRDY pin so that interrupts work properly.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In two of the gen5 socfpga devicetree files, there are some lines
indented using spaces instead of tabs.
Fix this by correctly indenting them with tabs.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Follow the recent trend for the license description.
This is also in an effort to fully sync the devicetrees with U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Our memory node will generate a warning in DTC since the unit address is
not matching the reg property. However, that node will be created by the
bootloader, so we can just remove it entirely in order to remove that
warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The MMC0 controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The i2c nodes were pre-populated to ease the use of overlays. However, now
that we provide default muxing options for those nodes, the one in the DTS
don't provide any content at all.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Now that all the SoCs using the tablet reference design DTSI are using the
same pinctrl naming scheme, we can move back the pinctrl phandles to the
main DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The pin groups are supposed to be in alphabetical order, and they aren't.
Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Most of our device trees have had leading zeros for padding as part of
the nodes unit-addresses.
Remove all these useless zeros that generate warnings
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
DTC will emit a warning on our OPPs nodes for the common DTSI between the
A23 and A33 since those nodes use the frequency as unit addresses, but
don't have a matching reg property.
Fix this by moving the frequency to the node name instead.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The #address-cells and #size-cells are only relevant for nodes that have
childs with reg properties. Otherwise, DTC will emit a warning saying that
those properties are unnecessary.
Remove them when needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The SOM204-EVB doesn't use the CTS pin, and thus was defining its own
pinctrl node for the UART3 muxing. Since we split away the TX and RX pin,
we can use the global node now, and only have the RTS pin in our local
node.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some UART nodes on the A20 DTSI do not share the same pattern that we use
everywhere else, with the RTS and CTS pins split away from the TX and RX
pins. Make those pin groups consistent with the rest of our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some gpio-keys definitions in our DTs were having buttons defined with a
unit-address and that would generate a DTC warning.
Change the buttons node names to remove the warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our I2C GPIO bus node name has a unit address, but no reg property, which
generates a warning in DTC. Change the name to remove that unit address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The I2C's, MMC0 and MMC1 controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
There's no phandle pointing to the CMA pool, so it's label is unnecessary.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CMA node has a unit address, but no reg property which generates a
warning in DTC. Change the node name to reflect its usage and drop the unit
address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Harmless mistake, but it's incorrect. The DT spec provides recommendations
for the node names:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model. If appropriate, the
name should be one of the following choices:
...
interrupt-controller"
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit adds QSPI flash support to the iwg23s board specific
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add QSPI[01] support to the RZ/G1C SoC specific device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables cmt0 support on the iWave iwg23s sbc.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CMT[01] support to r8a77470 SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB DMAC nodes.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables watchdog support on the iWave iwg23s sbc.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds watchdog support to the r8a77470 SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
[simon: moved node to preserve sort order]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the R-Mobile A1 (r8a7740), Emma Mobile EV2 (emev2) and
SH-Mobile AG5 (sh72a0) DTSI to include product name.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[simon: squashed similar patches]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LVDS0 encoder on Koelsh and Porter, and the LVDS1 encoder on Lager,
are enabled in DT but have no device connected to their output. This
result in spurious messages being printed to the kernel log such as
rcar-du feb00000.display: no connector for encoder /soc/lvds@feb90000, skipping
Fix it by disabling the encoders.
Fixes: 15a1ff30d8 ("ARM: dts: r8a7790: Convert to new LVDS DT bindings")
Fixes: e5c3f4707f ("ARM: dts: r8a7791: Convert to new LVDS DT bindings")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add uSD card and eMMC support to the iwg23s single board
computer powered by the RZ/G1C SoC (a.k.a. r8a77470).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Althought interface SDHI1 found on the RZ/G1C SoC (a.k.a.
r8a77470) is compatible with the R-Car Gen3 ones, its OF
compatibility is restricted to the SoC specific compatible
string to avoid confusion, as from a more generic perspective
the RZ/G1C is sharing the most similarities with the R-Car
Gen2 family of SoCs, and there is a combination of R-Car
Gen2 compatible SDHI IPs and R-Car Gen3 compatible SDHI IP
on this specific chip.
This patch adds the SoC specific part of SDHI1 support, and
since SDHI1 comes with internal DMA, its DT node looks fairly
different from SDHI0 and SDHI2.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
RZ/G1C comes with two different types of IP for the SDHI
interfaces, SDHI0 and SDHI2 share the same IP type, and
such an IP is also compatible with the one found in R-Car
Gen2. SDHI1 IP on the other hand is compatible with R-Car
Gen3 with internal DMA.
This patch completes the SDHI support of the R-Car Gen2
compatible IPs, including fixing the max-frequency
definition of SDHI2, as it turns out there is a bug in
Section 1.3.9 of the RZ/G1C Hardware User's Manual (Rev.
1.00 Oct. 2017).
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree nodes for the I2C[0123] controllers. Also, add
the aliases node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This provides a pinctrl driver for the Renesas R9A06G032 SoC
Based on a patch originally written by Michel Pollet at Renesas.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The interrupt-parent property is set in sun5i.dtsi, so there's no need to
repeat it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.
Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.
Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our HDMI output endpoint on the A10 DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Fix the 'unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property' DTC warning for the gpio-keys DT node on A10 boards.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
firmware and VCHI driver to coordinate on using the correct cache line
size for the platform.
-----BEGIN PGP SIGNATURE-----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=BEZr
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=zY4r
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2018-11-27' into devicetree/next
This pull request adds a compatible string to the DT necessary for the
firmware and VCHI driver to coordinate on using the correct cache line
size for the platform.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The H3 and H5 features the same CSI controller that was initially found on
the A31.
Add a DT node for it.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
cpu0-supply in cpu0 is deprecated, instead each cpu-core is supposed to
list its supply separately. With the added cpu core phandles, update
existing rk3188 boards accordingly.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The fact that OPPs specified only on cpu0 work is Linux specific and
normally cpu frequencies should be specified for each cpu core.
To facilitate this without needing to duplicate the frequency table
each time, convert to opp-v2 before adding references to all cores.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The Rockchip i2s always just requires a sound-dail-cells value of 0,
so add them to the core soc dtsi for convenience.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
The lradc's analog reference voltage is set to 3.0 volt in the
hardware. This is more or less set in copper for at least lradc0. Set the
property in the dts to ensure the lradc is referenced properly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pass the 'dmas' property to the UART ports so that DMA can
be supported.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It is not correct to assign the 24MHz clock oscillator to the GPIO
ports.
Fix it by assigning the proper GPIO clocks instead.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the Rockchip vendor tree the PMU interrupt number is
76, so fix it accordingly.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since firmware does not initialize any of the generic timer CPU
registers pass the 'arm,cpu-registers-not-fw-configured' property as
suggested in Documentation/devicetree/bindings/timer/arm,arch_timer.txt.
This also aligns with other Rockchip SoC dtsi files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Like it is done on cpu nodes of other Rockchip SoCs, pass the
'clock-latency' property to the CPU node, so that cpufreq driver
can take the latency into account when switching frequencies.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the pin settings for the emmc pins so they can be used across multiple
boards.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
DWC2 hardware module integrated in Samsung SoCs requires some quirks to
operate properly, so use Samsung SoC specific compatible to notify driver
to apply respective fixes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The T3/R40/V40 using the same sdk and config file in allwinner
sdk, it seem they are the same SOC just with different name, so
compatible with R40.
The t3-cqa3t-bv3 based on Allwinner T3 SoC, it has various connectors,
leds, buttons, and sell on:
https://item.taobao.com/item.htm?spm=2013.1.w4023-4203040713.25.62704cce7UCgLS&id=557154455330
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1/2 GB DDR3 DRAM
- 8 GB eMMC
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- 2 LVDS connectors
- 24 bit RGB LCD connector
- HDMI output
- DVP camera interface (support 500w cmos camera)
- GPIO connectors
- 5 TTL uarts and 2 RS232 uarts
- 1 RS485 connector
- support i2c capacitive tp and usb infrared tp
- boot control, reset and user buttons
- 3.5mm headphone and 3.5mm mic jack
- 100M RJ45
- micro SD card slot
- DC power jack
- RCT power slot
- 1 CVBS TVIN
- 1 CVBS TVOUT
- 2 customer leds
- 1 buzzer
- 1 minipcie
- I2C output
- SPI output
- PCM output
- wifi and bt connector reserved.
Board info can find here:
https://github.com/Axl-zhang/Allwinner-V40-T3-R40-manual
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The pwm-backlight driver initializes BLON (the enable gpio) to
output-high if the gpio is input on probe. Initializing the gpio
to output-low before the driver probes prevents this action by
the pwm-backlight driver and gets rid of a nasty blink of full
backlight with an uninitialized panel.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The SAMA5D2 is different from SAMA5D3 and SAMA5D4, as there are two
different clocks for the peripherals in the SoC. The Static Memory
controller is connected to the divided master clock.
Unfortunately, the device tree does not correctly show this and uses the
master clock directly. This clock is then used by the code for the NAND
controller to calculate the timings for the controller, and we end up with
slow NAND Flash access.
Fix the device tree, and the performance of Flash access is improved.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add sleep state for beeper pins. Without this there was a power
increase during the suspend and standby states on V3_3D domain.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl settings so that gpio0 wake from suspend will be supported
using buttons SW4 and SW7. Also, add pinctrl configuration for 0x954,
spi0_d0, which is an unused pin brought out to a header on the board
that in it's default state also connects to the gpio used for wakeup,
gpio0_3, which affects the state of the pin and prevents a working
wakeup unless we set the mux to a different state.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently uart0 uses pinctrl config set by bootloader so
create default state that can be restored after a suspend
event.
Also, modify uart0 pinctrl to include RTS and CTS pins as by
default these are not in a mode for optimal power savings.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pins used by debugss are not configued by default, place pulldowns
on the pins for maximum power savings during sleep.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[t-kristo@ti.com: converted to use AM4372_IOPAD macro]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several pins on this EVM that are not in use but they can
still draw power if misconfigured. Create a pinctrl entry for these pins
and configure each one for optimal power savings.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[t-kristo@ti.com: converted to use AM4372_IOPAD macro]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl data for ddr_vtt_toggle pin so that it is configured
for proper state during DeepSleep0. The pin should enter DS0 off mode
and hold the line low so VTT regulator is kept off while suspended.
It is also important for the PULLUP to be set on this pin so that
on removal of isolation, the VTT line is pulled high as a requirement
for bringing the DDR3 out of self-refresh.
This toggling is dependent on the IO isolation controlled by the
wkup_m3. Without placing the IOs into isolation the DS0 states set for
the pin will not be latched into effect during suspend.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As long as the kernel cmdline has "earlycon" in it, this allows
seeing debug messages earlier and does not require DEBUG_LL to
be enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EEPROM under I2C2 was put by mistake in the dts.
Remove it as it is not really present on the real hardware.
Fixes: ceef0396f3 ("ARM: dts: imx: add ZII RDU1 board")
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Coreboot version on veyron ChromeOS devices seems to ignore
memory@0 nodes when updating the available memory and instead
inserts another memory node without the address.
This leads to 4GB systems only ever be using 2GB as the memory@0
node takes precedence. So remove the @0 for veyron devices.
Fixes: 0b639b815f ("ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards")
Cc: stable@vger.kernel.org
Reported-by: Heikki Lindholm <holin@iki.fi>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There are two common DTSI files for Exynos5422 Odroid XU3 family of
boards. One is shared between all of them (XU3, XU3-Lite, XU4 and HC1)
and the second skips HC1. Document this in the files.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This allows a board to specify a custom thermal zone configuration
involving the SoC internal sensor, CPU and GPU nodes without having
to change those nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the correct compatible for the new protocol used by the firmware
on the touch controller, the GPIO wakeup isn't used in that case.
Also eGalax touch needs axis swapping, just as with the RMI4 touch.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch corrects indentation problems in the gpmigrp and i2c1grp nodes.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wireless variants of the ConnecCore 6UL SOM include a Qualcomm
QCA6564 wireless chip with dual WiFi and Bluetooth.
Both the ConnectCore 6UL SBC Express and Pro boards fit a wireless SOM.
The Wifi is connected through the SDIO interface on usdhc1 and the
Bluetooth is connected via uart1.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the status property disable the PCIe, the property will be enable
by bootloader.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Leave b{4,6}50v3 GPIO expander pca953x pins P05,P10,P11 unconfigured as
they are now used to implement an additional watchdog mechanism in user
space. P10,P11 pins remain unused (and therefore hogged) on b850v3.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support for this board is currently very limited. To debug any potential
issues on this board the "earlycon" kernel parameter can be used (without
any arguments). However, this requires the board to define a
/chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Support for this board is currently very limited. To debug any potential
issues on this board the "earlycon" kernel parameter can be used (without
any arguments). However, this requires the board to define a
/chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Support for Meson6 SoCs is currently very limited. It's often unclear
why such a device does not boot. To debug this the "earlycon" kernel
parameter can be used (without any arguments). However, this requires
the board to define a /chosen/stdout-path property in it's .dts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is no functional change from this, but it is confusing to find two
copies of vcc_sys and no vcc_flash when looking in
/sys/class/regulator/*/name.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This new property allows the number of sensors to be configured from DT
instead of being hardcoded in platform data. Use it.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We've earlier added support to split the register address space into TM
and SROT regions. Split up the regmap address space into two for msm8974
that has a similar register layout.
Since tsens-common.c/init_common() currently only registers one address
space, the order is important (TM before SROT). This is OK since the
code doesn't really use the SROT functionality yet.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since commit d7c5f68635 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
Fixes: d7c5f68635 ("ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813
regulator nodes")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[wens@csie.org: Reworked commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The i.MX25 contains two EPIT (Enhanced Periodic Interrupt Timer)
function blocks. Add their ipg and per clocks to the device tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set the eMMC max-frequency to 200MHz for optimal performance on Odroid
XU3/XU4 family of boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set the SD max-frequency to 200MHz for optimal performance on Odroid
XU3/XU4/HC1 family of boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
From Odroid XU3/XU4/HC1 schematics the LDO13 regulator for SD2, can be
set on 1.8V or 2.8V so the minimal value should be fixed to 1.8V. This
is necessary to support UHS-I tuning (otherwise card won't be detected
during boot).
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add support for UHS-I bus speed tuning for SDR50, DDR50 and SDR104 to
Odroid XU3/XU4/HC1 family boards.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Add missing clocks to SoC build-in RTC device to make it fully
operational on Exynos5250-based Arndale board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bindings for s2mps11/s5m8767 clocks driver require a compatible for
clocks node. Parent MFD sec-core driver will also use it when
instantiating children.
The compatible is not needed for proper working because device will be
anyway created by parent MFD device. Add it for correctness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bindings for s2mps11/s5m8767 clocks driver require a compatible for
clocks node. Parent MFD sec-core driver will also use it when
instantiating children.
The compatible is not needed for proper working because device will be
anyway created by parent MFD device. Add it for correctness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Spare dmas when using timers on stm32mp157c-ev1.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Spare dmas when using timer6 on stm32mp157c-ed1.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
At the same time the AM3517 EVM was gaining WiFi support,
separate patches were introduced to move the interrupt
from HIGH to RISING. Because they overlapped, this was not
done to the AM3517-EVM. This patch fixes Kernel 4.19+
Fixes: 6bf5e3410f ("ARM: dts: am3517-som: Add WL127x Wifi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt on mmc3_dat1 is wrong which prevents this from
appearing in /proc/interrupts.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV") #Kernel 4.9+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the Torpedo was first introduced back at Kernel 4.2,
the interrupt extended flag has been set incorrectly.
It was subsequently moved, so this patch corrects Kernel
4.18+
Fixes: a388673052 ("ARM: dts: Move move WiFi bindings to
logicpd-torpedo-37xx-devkit") # v4.18+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC1 is active low, not active high. For some reason,
this worked with different combination of U-Boot and kernels,
but it's supposed to be active low and is currently broken.
Fixes: cfaa856a25 ("ARM: dts: am3517: Add pinmuxing, CD and
WP for MMC1") #kernel 4.18+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The size field in a Device Tree "reg" property is encoded in bytes, not
words.
Fixes: 614fa22119 ("ARM: dts: bcm2835: Add VCHIQ node to the Raspberry Pi boards. (v3)")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
To allow VCHIQ to determine the correct cache line size, use the new
"brcm,bcm2836-vchiq" compatible string on BCM2836 and BCM2837.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
All boards replicate the aliases node, move the aliases node to
bcm-nsp.dtsi and add all the serial and ethernet ports such that a boot
program like u-boot can populate MAC addresses accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This matches licensing used by most of BCM5301X files and is preferred as:
1) GPL 2.0+ makes it clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
This file has been developed by me & once modified by Rob dropping a
single leading zero in an UART address.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Broadcom BCM963138DVT board has an eSATA port which is fully
functional, turn on the AHCI controller and the companion SATA PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This matches licensing used by most of BCM5301X files and is preferred as:
1) GPL 2.0+ makes it clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
This file was fully developed by me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This matches licensing used by other BCM5301X files and is preferred as:
1) GPL 2.0+ makes it clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
This file has been developed by me & once modified by Vivek.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This matches licensing used by other BCM5301X files and is preferred as:
1) GPL 2.0+ makes it clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
Both files were fully developed by me. Commits touching them were signed
by Florian and Hauke due to submitting process only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Mapleboard MP130 is a single board computer based on the Allwinner
H3 SoC, with all schematics freely available. The Lite version includes
1GB main memory and 8GB eMMC.
https://www.mapleboard.org/en (still mostly in Chinese even when English
is selected)
This DTS is based upon the DTS shipped with the board which uses
mapleboard,mp130- prefixes instead of the allwinner,sun8i variants.
v2: Fold in review comments from Maxime Ripard
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
QoS nodes keep information about priorites etc on the interconnect
and loose state when the power-domain gets disabled. Therefore the
power-domain driver stores the settings of available qos nodes and
restores them when the power-domain gets enabled again.
So add the qos nodes found on the Cortex-A9 socs from Rockchip, so
that they can then be connected to the power-domains.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Orange Pi Plus board lacks voltage scaling capabilities in its
current form. This results in random freezes during boot when cpufreq is
enabled, probably due to wrong voltages.
This patch (more or less copy/paste from 06139c) does the following
things on this board:
- enable r_i2c
- add sy8106a to the r_i2c bus
- have the sy8106a regulate VDD of cpu
Since the Orange Pi Plus has the same PMU setup as the Orange Pi PC, I
simply took min/max/fixed/ramp from the latter DTS. In that file the
origin of the values are described by the following comment:
"The datasheet uses 1.1V as the minimum value of VDD-CPUX,
however both the Armbian DVFS table and the official one
have operating points with voltage under 1.1V, and both
DVFS table are known to work properly at the lowest
operating point.
Use 1.0V as the minimum voltage instead."
I have tested this on patch two Orange Pi Plus boards, by running a
kernel with this patch and do intermettent runs of cpuburn while
monitoring voltage, frequency and temperature. The board runs stable
across its operatiing points while showing a reasonable (< 40C)
temperature. My Orange Pi PC, when put to the same test, yields similar
stable results.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The actual hardware has 4 data lines. Use them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Drop reg property from fixed regulator and remove the unncessary bus
node.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This would help us to get early boot logs by passing "earlycon" to
kernel bootargs.
Further, by adding this we don't have to depend on complex earlyprintk
configs for early boot logs.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DCP block on 6ull has no major differences other than requiring
explicit clock enabling.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds DTS support for BK4 device from Liebherr. It
uses vf610 SoC from NXP.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Pincfgs for UART4 to enable Communication with the onboard SAM3X
Signed-off-by: Markus Kueffner <kueffner.markus@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the ZII SCU 4 board, which has lots of switches and
SFF ports.
Based on the work from Andrew Lunn.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bindings for "fixed-regulator" only explicitly support "gpio" property,
not "gpios". Fix by correcting the property name.
The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
cycle, this can be handled by the phy-reset-gpios property. Sadly this
is not handled on suspend: the fec driver turns phy-supply off but
doesn't assert phy-reset-gpios again on resume.
Since additional phy-level work is required to support powering off the
phy in suspend fix the problem by just marking the regulator as
"boot-on" "always-on" so that it's never turned off. This behavior is
equivalent to older releases.
Keep the phy-reset-gpios property on fec anyway because it is a correct
description of board design.
This issue was exposed by commit efdfeb079c ("regulator: fixed:
Convert to use GPIO descriptor only") which causes the "gpios" property
to also be parsed. Before that commit the "gpios" property had no
effect, PHY reset was only handled in the the bootloader.
This fixes linux-next boot failures previously reported here:
https://lore.kernel.org/patchwork/patch/982437/#1177900https://lore.kernel.org/patchwork/patch/994091/#1178304
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A quoted label reference doesn't expand to the node path and is taken as
a literal string. Dropping the quotes can fix this unless the baudrate
string is appended in which case we have to use the alias.
At least on VF610, the problem was masked by setting the console in
bootargs. Use the alias syntax with baudrate parameter so we can drop
setting the console in bootargs.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the type of compatible string "fs,imx6sll-i2c" which should be
"fsl,imx6sll-i2c".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unused parameter from HASH1 dmas property on stm32mp157c SoC.
Fixes: 1e726a40e0 ("ARM: dts: stm32: Add HASH support on stm32mp157c")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[Olof: Bug doesn't cause any harm, so shouldn't need stable backport]
Signed-off-by: Olof Johansson <olof@lixom.net>
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
-----BEGIN PGP SIGNATURE-----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=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
