Currently mxs-auart doesn't care correctly about the baud rate divisor.
According to reference manual the baud rate divisor must be between
0x000000EC and 0x003FFFC0. So calculate the possible baud rate range
and use it for uart_get_baud_rate().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever the UART device driver gets closed from userland, the driver
disables the UART unit and then stops the clocks to save power.
The bit which disabled the UART unit is described as:
"UART Enable. If this bit is set to 1, the UART is enabled. Data
transmission and reception occurs for the UART signals. When the
UART is disabled in the middle of transmission or reception, it
completes the current character before stopping."
The important part is the "it completes the current character". Whenever
a reception is ongoing when the UART gets disabled (including the clock
off) the statemachine freezes and "remembers" this state on the next
open() when re-enabling the unit's clock.
In this case we end up receiving an additional bogus character
immediately.
The solution in this change is to switch the AUART unit into its reset
state on close() and only release it from its reset state on the next
open().
Note: when the unit is also used as system console it is always 'in use',
so we cannot reset it on close().
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function clears the reset the AUART unit is in after system start
to make it work.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512
We had add RS232/485 RTS control with fecf27a373. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).
This patch will modify 2 sections.
One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.
The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devtype structures are all declared as const.
Compiler does not complain because we cast
their pointers to save them in .driver_data.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).
Reported-by: Michael Allwright <michael.allwright@upb.de>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support ZTE uart with some registers differing offset.
Probe as platform device for not AMBA IP ID is
available on ZTE uart.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve LCRH register access decision as ARM PL011 lcrh
register serve as both TX and RX, while other SOC may
implement TX and RX function with separated register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce register look up table as different SOC venders
may have different register offset for the some register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce register accessor to ease loop up table access
in later patch.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename regs with enumeration to generalize register names.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).
Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.
NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.
Fixes: commit b5199d4681 ("tty/serial: at91: add support to FIFOs")
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementing enable_ms is optional by serial_core.
check_modem_status is just an empty local function.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.
Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RS485 control for Fintek F81504/508/512
F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.
When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.
When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.
When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.
We will force 0x01 on pci_fintek_setup().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e95044ba4f.
Commit e95044ba4f ("tty: serial: imx.c: Reset UART before activating
interrupts") terribly messes up with the console on mx6 boards, so
let's revert it.
Reported-by: kernelci.org bot <bot@kernelci.org>
Cc: David Jander <david@protonic.nl>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this driver is currently:
config SERIAL_SUNHV
bool "Sun4v Hypervisor Console support"
...meaning that it currently is not being built as a module by
anyone. Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't swap module.h for init.h since this file has init.h already.
We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value. Also note that MODULE_DEVICE_TABLE is a
no-op for non-modular code, so we remove that too.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this driver is currently:
config SERIAL_SUNCORE
bool
...meaning that it currently is not being built as a module by
anyone. Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't swap module.h for init.h since this file has init.h already.
We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this option is currently:
config SERIAL_LANTIQ
bool "Lantiq serial driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We delete the MODULE_DESCRIPTION and LICENSE tags since they are
not adding any new information above and beyond what is at the top
of the file. Also note that MODULE_DEVICE_TABLE is a no-op for
non-modular code, so we remove that as well.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig for this option is currently:
config SERIAL_SGI_L1_CONSOLE
bool "SGI Altix L1 serial console support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the orphaned module code, so that when reading the
driver there is no doubt it is builtin-only. We could consider
making it tristate, but the above bool has been there since before
the start of git history, which isn't all that surprising, since
consoles are typically critical to have at early boot. So adding
tristate is really of no value here.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 84f57d9e36 ("tty: serial/samsung: fix modular build") fixed
build issues when the driver was built as a module. One of those was
that printascii is only accessible when the driver is built-in.
But there is no need to check for defined(CONFIG_DEBUG_LL) since the
SERIAL_SAMSUNG_DEBUG Kconfig symbol already depends on DEBUG_LL.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While closing, new rx data may be received after the input buffers
have been flushed but before stop_rx() halts receiving [1]. The
new data might not be processed by flush_to_ldisc() until after
uart_shutdown() and normal input processing is re-enabled (ie.,
tty->closing = 0). The race is outlined below:
CPU 0 | CPU 1
|
uart_close() |
tty_port_close_start() |
tty->closing = 1 |
tty_ldisc_flush() |
| => IRQ
| while (LSR & data ready)
| uart_insert_char()
| tty_flip_buffer_push()
| <= EOI
stop_rx() | .
uart_shutdown() | .
free xmit.buf | .
tty_port_tty_set(NULL) | .
tty->closing = 0 | .
| flush_to_ldisc()
| n_tty_receive_buf_common()
| __receive_buf()
| ...
| commit_echoes()
| uart_flush_chars()
| __uart_start()
| ** OOPS on port.tty deref **
tty_ldisc_flush() |
Input processing must be prevented from echoing (tty->closing = 1)
until _after_ the input buffers have been flushed again at the end
of uart_close().
[1] In fact, some input may actually be buffered _after_ stop_rx()
since the rx interrupt may have already triggered but not yet been
handled when stop_rx() disables rx interrupts.
Fixes: 2e75891083 ("serial: core: Flush ldisc after dropping port
mutex in uart_close()")
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum bitrate supported depends on the clock rate used in BRG.
This is stored in port.uartclk during probe. Respecting the 16x
oversampling higher bitrates can be supported.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now this improvement is only used with TX DMA transfers. The data
width must be set properly when configuring the DMA controller. Also
the FIFO configuration must be set to match the DMA transfer data
width:
TXRDYM (Transmitter Ready Mode) and RXRDYM (Receiver Ready Mode) must
be set into the FIFO Mode Register. These values are used by the
USART to trigger the DMA controller. In single data mode they are not
used and should be reset to 0.
So the TXRDYM bits are changed to FOUR_DATA; then USART triggers the
DMA controller when at least 4 data can be written into the TX FIFO
througth the THR. On the other hand the RXRDYM bits are left unchanged
to ONE_DATA.
Atmel eXtended DMA controller allows us to set a different data width
for each part of a scatter-gather transfer. So when calling
dmaengine_slave_config() to configure the TX path, we just need to set
dst_addr_width to the maximum data width. Then DMA writes into THR are
split into up to two parts. The first part carries the first data to
be sent and has a length equal to the greatest multiple of 4 (bytes)
lower than or equal to the total length of the TX DMA transfer. The
second part carries the trailing data (up to 3 bytes). The first part
is written by the DMA into THR using 32 bit accesses, whereas 8bit
accesses are used for the second part.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the hardware, TX and RX FIFOs may be available. The RX
FIFO can avoid receive overruns, especially when DMA transfers are
not used to read data from the Receive Holding Register. For heavy
system load, The CPU is likely not be able to fetch data fast enough
from the RHR.
In addition, the RX FIFO can supersede the DMA/PDC to control the RTS
line when the Hardware Handshaking mode is enabled. Two thresholds
are to be set for that purpose:
- When the number of data in the RX FIFO crosses and becomes lower
than or equal to the low threshold, the RTS line is set to low
level: the remote peer is requested to send data.
- When the number of data in the RX FIFO crosses and becomes greater
than or equal to the high threshold, the RTS line is set to high
level: the remote peer should stop sending new data.
- low threshold <= high threshold
Once these two thresholds are set properly, this new feature is
enabled by setting the FIFO RTS Control bit of the FIFO Mode Register.
FIFOs also introduce a new multiple data mode: the USART works either
in multiple data mode or in single data (legacy) mode.
If MODE9 bit is set into the Mode Register or if USMODE is set to
either LIN_MASTER, LIN_SLAVE or LON_MODE, FIFOs operate in single
data mode. Otherwise, they operate in multiple data mode.
In this new multiple data mode, accesses to the Receive Holding
Register or Transmit Holding Register slightly change.
Since this driver implements neither the 9bit data feature (MODE9 bit
set into the Mode Register) nor LIN modes, the USART works in
multiple data mode whenever FIFOs are available and enabled. We also
assume that data are 8bit wide.
In single data mode, 32bit access CAN be used to read a single data
from RHR or write a single data into THR.
However in multiple data mode, a 32bit access to RHR now allows us to
read four consecutive data from RX FIFO. Also a 32bit access to THR
now allows to write four consecutive data into TX FIFO. So we MUST
use 8bit access whenever only one data have to be read/written at a
time.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the UART_PUT_*, resp. UART_GET_*, macros by
atmel_uart_writel(), resp. atmel_uart_readl(), inline function calls.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XR17V35X UART needs the ECB bit set in its XR_EFR
register to enable access to IER [7:5], ISR [5:4], FCR[5:4],
MCR[7:5], and MSR [7:0].
Also reset the IER register to mask interrupts after access
to all bits of this register has been enabled.
This makes my 8-port XR17V35X working with the in-kernel
serial driver.
Cc: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An already-active sender can swamp the interrupt handler with
"too much work" if the rx interrupts are enabled when the fifo is
disabled and operating in single-byte mode.
Defer rx and line status interrupt enable until after the fifos
are enabled in set_termios(), but at least initialize the shadow
IER value with the interrupts which will be enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ed71871bed ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override
However recent updates to core, specifically ebc5e20082 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3fee
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 068500e08d.
According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the UART has been in use before this driver was loaded, IRQs might be
active and get fired as soon as we set the handler, which will crash
in the spin_lock_irqsave(&sport->port.lock, flags) because port.lock is
not initialized until the port is added at the end of probe.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To prevent problems with interrupt latency, and due to the fact, that
the error will be counted anyway (icount.overrun), the dev_err is simply
removed.
Background:
If an rx-fifo overflow occurs a dev_err message was called in interrupt
context. Since dev_err messages are written to console in a synchronous way
(unbuffered), and console may be a serial terminal, this leads to a
highly increased interrupt-latency (several milliseconds).
As a result of the high latency more rx-fifo overflows will happen, and
therefore a feedback loop of errors is created.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Acked-By: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As can be seen in function uart_insert_char (serial_core) the element
buf_overrun of struct uart_icount is used to count overruns of
tty-buffer.
Added support for counting of overruns in imx driver analogue to
serial_core.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable interrupts before requesting them in order to fix a kernel oops
after lauching a kernel via kexec.
Tested on a imx6sl-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Being a soft core, it can be located not only on PPC or Microblaze
platforms.
Since the driver already does endianness detection we only need to
change the Kconfig to use it in other arches.
This is also done in other softcores as xilinx-spi.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SysRq support activation depends on CONFIG_SERIAL_STM32_USART_CONSOLE, but
this config flag does not exists.
This patch fix this by depending on the valid config flag, which is
SERIAL_STM32_CONSOLE.
Reported-by: Andreas Ruprecht <andreas.ruprecht@fau.de>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to regmap_raw_read/write needed register rewrite in a
similar way as function calls to regmap_read/write already had.
This enables reading/writing the serial datastream to the device.
Signed-off-by: Bo Svangård <bo.svangard@embeddedart.se>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I2C=m and SPI=y or-ing them will produce =y while
what we need is the lower bound, i.e. =m. Fortunately
SPI is a boolean so we need to handle only one special
case.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While UART work in DMA mode, function start_rx will request descriptor
from DMA engine, if there is no left descriptor UART, driver will give
err logs "DMA slave single fail".
currently start_rx is called in set_termios function, so everytime, port
setting will call start_rx once.
Now put start_rx in startup, it will be called once while open the port.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when UART works in DMA mode and left bytes in rx fifo less than
a dma transfer unit, DMA engine can't transfer the bytes out
to rx DMA buffer. so it need a way to fetch them out and
flush them into tty buffer in time.
in the above case, we want UART switch from DMA mode to PIO mode and
fetch && flush bytes into tty layer buffer until rxfifo become empty,
after that done let UART switch from PIO mode back to DMA mode.
(record as method1)
method1 result in the next receive result wrong. for example in PIO part
of method1, we fetched && pushed X1...X3 bytes, when UART rxfifo newly
received Y1...Y4 bytes, UART trigger a DMA unit transfer, the DMA unit's
content is X1...X3Y1 and rxfifo fifo status is empty, so X1X2X3 pushed
twice by PIO way and DMA way also the bytes Y2Y3Y4 missed. add rxfifo
reset operation before UART switch back to DMA mode would resolve the
issue. ([method1 + do fifo reset] record as method2)
before the commit, UART driver use method2. but methd2 have a risk of
data loss, as if UART's shift register receive a complete byte and
transfer it into rxfifo before rxfifo reset operation the byte will
loss.
UART and USP have the similar bits CLEAR_RX_ADDR_EN(uart)/FRADDR_CLR_EN(usp),
When found UART controller changing I/O to DMA mode, UART controller
clears the two low bits of read point (rx_fifo_addr[1:0]).
when enable the bit + method1(record as method3), in above example
the DMA unit's content is X1...X3Y1 and there are Y2Y3Y4 in rxfifo by
experiment, we just push bytes in rx DMA buffer.
BTW, the workaround works only for UART receive DMA channel use SINGLE
DMA mode.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe, we use dev_id as array index of etraxfs_uart_ports and store the
index in port->line. So etraxfs_uart_ports[port->line] should be released
when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of cris_console_device() is exactly the same as
uart_console_device(), so let's switch to use uart_console_device().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP h/w-assisted IXON flow control is borked. The transmitter becomes
stuck if XON is never received; clearing the fifos or resetting the
rx flow control bits has no effect.
Remove auto-IXANY as well, since without auto-IXON, it has no purpose.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to Advisory 21 as documented in AM437x errata document,
UART module cannot be disabled once DMA is used. The only
workaround is to softreset the module before disabling it.
DRA7x UARTs are compatible to AM437x UARTs in terms of
this errata and prescribed workaround.
Enable usage of workaround for this errata on DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM335x, AM437x and DRA7x SoCs have an errata[1] due to which UART
cannot be idled after it has been used with DMA.
OMAP3 has a similar sounding errata which has been worked around
in a2fc36613a ("ARM: OMAP3: Use manual idle for UARTs
because of DMA errata"). But the workaround used there does not
apply to AM335x, AM437x SoCs.
After using DMA, the UART module on these SoCs must be soft reset
to go to idle.
This patch implements that errata workaround. It is expected that
UART will be used with DMA so no explicit check for DMA usage
has been added for errata applicability.
MDR1 register needs to be restored right after soft-reset because
"UART mode" must be set in that register for module wake-up on AM335x
to work. As a result, SCR register is now used to determine if
context was lost during sleep.
[1] See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of of_machine_is_compatible() for handling AM335x specific
"DMA kick" quirk in 8250_omap driver makes it ugly to extend the
quirk for other platforms. Instead use a new compatible.
The new compatible will also make it easier to take care of
other quirks on AM335x and like SoCs.
In order to not break backward DTB compatibility for users of
8250_omap driver on AM335x based boards, existing use of
of_machine_is_compatible() has not been removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The silicon errata[1] workaround implemented in a follow-on
patch, "serial: 8250_omap: workaround errata on disabling
UART after using DMA", requires MDR1 register programming.
Extract MDR1 register update into helper function,
omap8250_update_mdr1() to help with that.
[1] Advisory 21 in http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_device infrastructure has a suspend_noirq hook which
runtime suspends all devices late in the suspend cycle (see
_od_suspend_noirq() in arch/arm/mach-omap2/omap_device.c)
This leads to a NULL pointer exception in 8250_omap driver
since by the time omap8250_runtime_suspend() is called, 8250_dma
driver has already set rxchan to NULL via serial8250_release_dma().
Make an explicit check to see if rxchan is NULL in
runtime_{suspend|resume} hooks to fix this.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be configured for io addresses different than the standard.
Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip can be configured to use entry key different than 0x77. Try all the
valid keys until one gives out the right chip id.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some chips with the same interface but different chip ip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be connected at address 0x4e and also 0x2e.
Add some logic to find out the address of the chip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the port index and the line id in a private structure.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bhUU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fE8E
-----END PGP SIGNATURE-----
Merge tag 'for-4.2' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux
Pull Renesas H8/300 architecture re-introduction from Yoshinori Sato.
We dropped arch/h8300 two years ago as stale and old, this is a new and
more modern rewritten arch support for the same architecture.
* tag 'for-4.2' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux: (27 commits)
h8300: fix typo.
h8300: Always build dtb
h8300: Remove ARCH_WANT_IPC_PARSE_VERSION
sh-sci: Get register size from platform device
clk: h8300: fix error handling in h8s2678_pll_clk_setup()
h8300: Symbol name fix
h8300: devicetree source
h8300: configs
h8300: IRQ chip driver
h8300: clocksource
h8300: clock driver
h8300: Build scripts
h8300: library functions
h8300: Memory management
h8300: miscellaneous functions
h8300: process helpers
h8300: compressed image support
h8300: Low level entry
h8300: kernel startup
h8300: Interrupt and exceptions
...
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
There is much SCI of SoC having within,
and the register size is also different in everyone.
So get from platform device.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Acked-by: by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Introduce a driver suitable for use with the UARTs present in
Ingenic SoCs such as the JZ4740 & JZ4780. These are described as being
ns16550 compatible but aren't quite - they require the setting of an
extra bit in the FCR register to enable the UART module. The serial_out
implementation is the same as that in arch/mips/jz4740/serial.c - which
will shortly be removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-serial@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In platforms which does not use CLK framework (HAVE_CLK not set), the
clk_* functions return NULL instead of an error. This patch handles that
scenario.
Signed-off-by: Fernando Guzman Lugo <fernando.guzman.lugo@intel.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The internal clock of the master chip, which is usually 125MHz, is only half
(62.5MHz) for the slave chips. So we have to adjust the uartclk for all the
slave ports. Therefor we add a new function to determine if a slave chip is
present and update pci_xr17v35x_setup accordingly.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR17V358 can also be combined with a XR17V354 chip to act as a
single 12 port chip. This works the same way as the combining two XR17V358
chips. But the reported device id then is 0x4358.
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align with coding guidelines:
Replaced a chain of "else if" by a switch case.
Signed-off-by: Joakim Nordell <joakim.nordell@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This drivers adds support to the STM32 USART controller, which is a
standard serial driver.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also set IRQ_NOPROBE and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial port driver for the 8250-based UART found on LPC18xx/43xx
devices. The UART is 16550A compatible with additional features
like RS485 support, synchronous mode, IrDA, and DMA.
For now only basic UART and RS485 operation is supported.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver for on-chip UART used on UniPhier SoCs.
This hardware is similar to 8250, but the register mapping is
slightly different:
- The offset to FCR, MCR is different.
- The divisor latch access bit does not exist. Instead, the
divisor latch register is available at offset 9.
This driver overrides serial_{in,out}, dl_{read,write} callbacks,
but wants to borrow most of code from 8250_core.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On many new Intel SoCs the UART has an integrated DMA engine
(iDMA). In order to use it a special filter function is needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function clk_prepare_enable() may fail, and in that case it
does not make sense to proceed. Let's check its return code and
error out if it is a negative value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe method of this driver calls clk_get(), but clk_put() is
missing from the remove callback.
Using the managed clk function is easier than fixing other parts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support command line parameters of the form:
earlycon=<name>,io|mmio|mmio32|mmio32be,<addr>,<options>
This commit seem to be needed even after commit:
serial: 8250: Add support for big-endian MMIO accesses
c627f2ceb6
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the serial works as a bluetooth sink, due to audio realtime
requirement, the driver should have something similar with ALSA:
1. one big DMA buffer to easy the schedule jitter
2. split this big DMA buffer to multiple small periods, for each
period, we get a DMA interrupt, then push the data to userspace.
the small periods will easy the audio latency.
so ALSA generally uses a cyclic chained DMA.
but for sirfsoc, the dma hardware has the limitation: we have
only two loops in the cyclic mode, so we can only support two
small periods to switch. if we make the DMA buffer too big, we
get long latency, if we make the DMA buffer too little, we get
miss in scheduling for audio realtime.
so this patch moves to use a hrtimer to simulate the cyclic
DMA, then we can have a big buffer, and also have a timely
data push to users as the hrtimer can generate in small period
then actual HW interrupts.
with this patch, we also delete a lot of complex codes to handle
loop buffers, and RX timeout interrupt since the RX work can be
completely handled from hrtimer interrupt.
tests show using this way will make our bad audio streaming be-
come smooth.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A corner case exists in the current driver. if an app opens the console
device, and before writing to console device, and there are huge kernel
ogs to print out, system will hang on
sirfsoc_uart_console_putchar:
while (rd_regl(port, ureg->sirfsoc_tx_fifo_status) &
ufifo_st->ff_full(port->line))
cpu_relax();
as in sirfsoc_uart_startup(), the driver assigns tx_fifo_op to 0 will stop
TX FIFO, this loop will be endless.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_set_mctrl() is a void type function. Returning something
does not look nice.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS-485 configuration is also done under the spinlock
so no blocking I/O allowed.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.stop_rx/tx() are called in atomic context, we cannot use
blocking I/O. While at it correct the name of RX bit and
'*' placement in pointer declarations.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert md_proc into general async reconfiguration procedure.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of spinning under port->lock let's just sleep
inside the kthread. It should be equivalent as TX cannot
proceed when thread is blocked.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert workqueue usage to a real-time kworker. The problem
with workqueues is that we cannot set real-time priorities on
our work and asynchronous reconfiguration can be blocked by
less important tasks.
We need kthread for the interrupt anyway and because we will
now be using single kthread for all TX-related operations we
can get rid of the port mutex.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LSR_TEMT_BIT (LSR bit 6) provides us exactly the information
we need to determine if transmission is finished - FIFO level
and shift register empty. We can save ourselves reading FIFO
level explicitly if we use this bit.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without matching bus-specific strings driver will not be loaded
automatically.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users of RS-485 can request via ioctl that RTS signals should
be activated selected number of milliseconds before the actual
data transmission or delay reception certain number of milli-
seconds after the transmission is finished. In sc16is7xx,
however, RTS signalling is handled by the hardware and driver
has no way of providing this feature.
We still try to provide .delay_rts_before_send by delaying
transmission but without actual effect on the RTS line.
Note: this change will make the driver return -EINVAL when the
feature is requested (.delay_rts_after_send is set).
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spi interface for sc16is7xx is added along with Kconfig flag
to enable spi or i2c, thus in a instance we can have either
spi or i2c or both, in sync to the hw.
Signed-off-by: Rama Kiran Kumar Indrakanti <indrakanti_ram@hotmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the necessary driver boilerplate to let the driver be used when
the respective ACPI table is discovered by the ACPI subsystem.
[Andre: change table name, add MODULE_DEVICE_TABLE entry and improve
commit message]
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARM Server Base System Architecture[1] document describes a
generic UART which is a subset of the PL011 UART.
It lacks DMA support, baud rate control and modem status line
control, among other things.
The idea is to move the UART initialization and setup into the
firmware (which does this job today already) and let the kernel just
use the UART for sending and receiving characters.
We use the recent refactoring to build a new struct uart_ops
variable which points to some new functions avoiding access to the
missing registers. We reuse as much existing PL011 code as possible.
In contrast to the PL011 the SBSA UART does not define any AMBA or
PrimeCell relations, so we go with a pretty generic probe function
which only uses platform device functions.
A DT binding is provided with this patch, ACPI support is added in a
separate one.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBSA UART has a fixed baud rate and flow control setting, which
cannot be changed or queried by software.
Add a vendor specific property to always return fixed values when
trying to read the console options.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBSA UART should not be enabled or disabled (it is always on),
and consequently the spec lacks the UART_CR register.
Add a vendor specific property to skip disabling or enabling of the
UART. This will be used later by the SBSA UART support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid lines with more than 80 characters and to make the
pl011_int() function more readable, move the workaround out into a
separate function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 register UART_MIS is actually a bitwise AND of the
UART_RIS and the UART_MISC register.
Since the SBSA UART does not include the _MIS register, use the
two separate registers to get the same behaviour. Since we are
inside the spinlock and we read the _IMSC register only once, there
should be no race issue.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the pl011_probe() function is relying on some AMBA IDs
and a device tree node to initialize the driver and a port.
Both features are not necessarily required for the driver:
- we lack AMBA IDs in the ARM SBSA generic UART and
- we lack a DT node in ACPI systems.
So lets refactor the function to ease later reuse.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the pl011_set_termios() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the pl011_shutdown() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the pl011_startup() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although we care about not unregistering the driver if there are
still ports connected during the .remove callback, we do miss this
check in the pl011_probe function. So if the current port allocation
fails, but there are other ports already registered, we will kill
those.
So factor out the port removal into a separate function and use that
in the probe function, too.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the mediatek serial port driver is built-in, but serial
console is disabled in Kconfig (e.g. when the serial driver
itself is a loadable module), we get this build error:
drivers/built-in.o: In function `early_mtk8250_setup':
undefined reference to `early_serial8250_setup'
To avoid that problem, this patch encloses the early_mtk8250_setup
function in #ifdef CONFIG_SERIAL_8250_CONSOLE, the same symbol
that guards the early_serial8250_setup function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A configuration that enables earlycon but not the core console
code causes a link error:
drivers/built-in.o: In function `setup_earlycon':
drivers/tty/serial/earlycon.c:70: undefined reference to `uart_parse_earlycon'
That error can be triggered by the newly added samsung earlycon support,
which is missing a 'select' statement.
As suggested by Peter Hurley, solves the problem by moving the
'select SERIAL_EARLYCON' statement to the samsung console driver
option, as it is done by all other console drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b94ba0328d ("serial: samsung: Add support for early console")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function mctrl_gpio_init returns failure if the assignment to any
member of the gpio array results in an error pointer. So there is no
need to check for such error values in the other functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to dmaengine_slave_config() fails, then the DMA buffer will
not be freed/unmapped. Fix this by moving the code that stores the
address of the buffer in the tegra_uart_port structure to before the
call to dmaengine_slave_config().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
it seems this is a more typical behaviour from reviewing other console
drivers.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add overrun error's flag mark and parity's counter, we can show the
statistic from procfs node.
BTW, let the indentation of stick bits configuration look better.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In special condition, when cpu schedule into rx_tmo_process_tl or
rx_dma_complete_tl and all the receive dma tasks have done, it will
go into endless loop because no dma task cookie status be changed.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From HW spec, when rxfifo's data is less than AFC_RX_THD(RX threshhold), RTS
signal is active. otherwise, RTS signal is inactive.
Crrently the RX threshhold is set as zero, so RTS has no chance to be
active. This patch replaces the default 0 by a positive number.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
differentiate difference port types by re-defining the status MARCO
or putting HW differences into private data of the related ports.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...
Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.
Reported-by: Sami Pietikäinen <Sami.Pietikainen@wapice.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.
This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Reported-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 734745caeb serial/amba-pl011:
(Activate TX IRQ passively) introduces a race which causes the driver
sometimes to attempt to write a character to the TX FIFO when the FIFO
is already full.
The PL011 does not guarantee its behaviour when the FIFO is overfilled.
In practice, this can cause duplicate and/or dropped characters to be
output on the wire. The problem is common enough to be readily
observable on the ARM Juno platform when the PL011 UART is used as
the console and DMA is not in use.
This patch fixes this problem by always polling for space before each
character is written to the FIFO.
This will be amended to a less brute-force approach in a later commit,
but this patch should help ensure correct behaviour for now.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 02730d3c05
(Merge 4.1-rc4 into tty-next), git mismerged some lines,
reintroducing a reference to the removed field
uart_amba_port.tx_irq_seen. This causes a build failure.
This patch removes the mismerged lines, restoring the code to what
was in tty-next (which was the intention).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is no longer used now that mach-msm has been removed.
Delete it.
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function tegra_uart_dma_channel_allocate() does not check that
dma_map_single() mapped the DMA buffer correctly. Add a check for this
and appropriate error handling.
Furthermore, if dmaengine_slave_config() (called by
tegra_uart_dma_channel_allocate()) fails, then memory allocated/mapped
is not freed/unmapped. Therefore, call tegra_uart_dma_channel_free()
instead of just dma_release_channel() if dmaengine_slave_config() fails.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues in the shutdown path of the UARTs which are:
1. The function tegra_uart_shutdown() calls tegra_uart_flush_buffer()
to stop DMA TX transfers. However, tegra_uart_flush_buffer() is
called after the DMA channels have already been freed and so actually
does nothing.
2. The function that frees the DMA channels
(tegra_uart_dma_channel_free()), unmaps the dma buffer before
freeing the DMA channel and does not ensure the DMA has been
stopped.
Resolve this by fixing the code in tegra_uart_dma_channel_free() to
ensure the DMA is stopped, free the DMA channel and then unmap the DMA
buffer. Finally, remove the unnecessary call to tegra_uart_flush_buffer().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA cookie for the RX channel is being used by the TX channel.
Therefore, fix driver to use the correct DMA cookie for the TX channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() takes an argument "size" which is
of type size_t. This is an unsigned type. Update the count,
rx_bytes_requested and tx_bytes_requested in the tegra serial driver to
be unsigned integers so that an unsigned type is passed to
tty_insert_flip_string().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra serial driver has two paths through which receive data is
copied up to the tty layer. These are:
1. DMA completion callback
2. UART RX interrupt
A UART RX interrupt occurs for either RX_TIMEOUT (data has been sitting
in the Rx FIFO for more than 4 character times without being read
because there is not enough data to reach the trigger level), End of
Receive Data event (receiver detects that data stops coming in for more
than 4 character times) or a receive error.
In the RX interrupt path, the following happens ...
- All RX DMA transfers are stopped
- Any data in the DMA buffer and RX FIFO are copied up to the tty layer.
- DMA is restarted/primed for the RX path
In the DMA completion callback, the DMA buffer is copied up to the tty
layer but there is no check to see if the RX interrupt could have
occurred between the DMA interrupt firing the the DMA callback running.
Hence, if a RX interrupt was to occur shortly after the DMA completion
interrupt, it is possible that the RX interrupt path has already copied
the DMA buffer before the DMA callback has been called. Therefore, when
the DMA callback is called, if the DMA is already in-progress, then this
indicates that the UART RX interrupt has already occurred and there is
nothing to do in the DMA callback. This race condition can cause
duplicated data to be received.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Moved async_tx_ack() call to after check to see
if DMA has completed because if the DMA is in progress we do not need
to ACK yet. Changed the print from dev_info to dev_debug. Updated
changelog to add more commentary on the race condition based upon
feedback from author.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is only necessary to read data from the dma buffer when the count
value is non-zero and hence, tegra_uart_copy_rx_to_tty() so only be
called when this is the case.
Although, this was being tested for in two places, there is a third
place where this was not tested. However, instead of adding another
if-statement prior to calling tegra_uart_copy_rx_to_tty(), move the test
inside the function.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Re-worked patch to move the check for the count
value inside the function tegra_uart_copy_rx_to_tty(). Updated
changelog with more commentary.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 3 UART clock periods after enabling
the TX fifo, otherwise data could be lost.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 32 UART clock periods for the flush
to propagate otherwise TX data could be post. Add a helper function
to wait for N UART clock periods and update delay following FIFO
flush to be 32 UART clock cycles.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port.type has already been set by of_platform_serial_setup()
called from a few lines above.
Setting it to the same value is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port.fifosize member has already been copied at 8 lines above.
Maybe the compiler optimization can clean it away, but just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early console functions are only used during the early boot stage.
This change just saves a small amount of memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When nr_uarts was set to 0 (via config or 8250_core.nr_uarts), we crash
early on x86 because serial8250_isa_init_ports dereferences base_ops
which remains NULL. In fact, there is nothing to do for all the callers
of serial8250_isa_init_ports if there are no uarts.
Based on suggestions by Peter Hurley.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Staticize symbols not exported and not used outside of file.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
