Extend chip select number supported by spi master as well
because we can accept SPISEL1-SPISEL7 and all GPIO.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The SYSTEM_SUSPEND_DISK system state is never used, so drop it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge emailed kgdb dmesg fixups patches from Anton Vorontsov:
"The dmesg command appears to be broken after the printk rework. The
old logic in the kdb code makes no sense in terms of current
printk/logging storage format, and KDB simply hangs forever upon
entering 'dmesg' command.
The first patch revives the command by switching to kmsg_dumper
iterator. As a side-effect, the code is now much more simpler.
A few changes were needed in the printk.c: we needed unlocked variant
of the kmsg_dumper iterator, but these can surely wait for 3.6.
It's probably too late even for the first patch to go to 3.5, but I'll
try to convince otherwise. :-) Here we go:
- The current code is broken for sure, and has no hope to work at
all. It is a regression
- The new code works for me, and probably works for everyone else;
- If it compiles (and I urge everyone to compile-test it on your
setup), it hardly can make things worse."
* Merge emailed patches from Anton Vorontsov: (4 commits)
kdb: Switch to nolock variants of kmsg_dump functions
printk: Implement some unlocked kmsg_dump functions
printk: Remove kdb_syslog_data
kdb: Revive dmesg command
The locked variants are prone to deadlocks (suppose we got to the
debugger w/ the logbuf lock held), so let's switch to nolock variants.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If used from KDB, the locked variants are prone to deadlocks (suppose we
got to the debugger w/ the logbuf lock held).
So, we have to implement a few routines that grab no logbuf lock.
Yet we don't need these functions in modules, so we don't export them.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function is no longer needed, so remove it.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kgdb dmesg command is broken after the printk rework. The old logic
in kdb code makes no sense in terms of current printk/logging storage
format, and KDB simply hangs forever.
This patch revives the command by switching to kmsg_dumper iterator.
The code is now much more simpler and shorter.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull late MIPS fixes from Ralf Baechle:
"This fixes a number of lose ends in the MIPS code and various bug
fixes.
Aside of dropping some patch that should not be in this pull request
everything has sat in -next for quite a while and there are no known
issues.
The biggest patch in this patch set moves the allocation of an array
that is aliased to a function (for runtime generated code) to
assembler code. This avoids an issue with certain toolchains when
building for microMIPS."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (35 commits)
MIPS: PCI: Move fixups from __init to __devinit.
MIPS: Fix bug.h MIPS build regression
MIPS: sync-r4k: remove redundant irq operation
MIPS: smp: Warn on too early irq enable
MIPS: call set_cpu_online() on cpu being brought up with irq disabled
MIPS: call ->smp_finish() a little late
MIPS: Yosemite: delay irq enable to ->smp_finish()
MIPS: SMTC: delay irq enable to ->smp_finish()
MIPS: BMIPS: delay irq enable to ->smp_finish()
MIPS: Octeon: delay enable irq to ->smp_finish()
MIPS: Oprofile: Fix build as a module.
MIPS: BCM63XX: Fix BCM6368 IPSec clock bit
MIPS: perf: Fix build error caused by unused counters_per_cpu_to_total()
MIPS: Fix Magic SysRq L kernel crash.
MIPS: BMIPS: Fix duplicate header inclusion.
mips: mark const init data with __initconst instead of __initdata
MIPS: cmpxchg.h: Add missing include
MIPS: Malta may also be equipped with MIPS64 R2 processors.
MIPS: Fix typo multipy -> multiply
MIPS: Cavium: Fix duplicate ARCH_SPARSEMEM_ENABLE in kconfig.
...
- avoid a crash in dm-raid1 when discards coincide with mirror recovery;
- avoid discarding shared data that's still needed in dm-thin;
- don't guarantee that discarded blocks will be wiped in dm-raid1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gbLp
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper discard fixes from Alasdair G Kergon:
- avoid a crash in dm-raid1 when discards coincide with mirror
recovery;
- avoid discarding shared data that's still needed in dm-thin;
- don't guarantee that discarded blocks will be wiped in dm-raid1.
* tag 'dm-3.5-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm raid1: set discard_zeroes_data_unsupported
dm thin: do not send discards to shared blocks
dm raid1: fix crash with mirror recovery and discard
Pull pnfs/ore fixes from Boaz Harrosh:
"These are catastrophic fixes to the pnfs objects-layout that were just
discovered. They are also destined for @stable.
I have found these and worked on them at around RC1 time but
unfortunately went to the hospital for kidney stones and had a very
slow recovery. I refrained from sending them as is, before proper
testing, and surly I have found a bug just yesterday.
So now they are all well tested, and have my sign-off. Other then
fixing the problem at hand, and assuming there are no bugs at the new
code, there is low risk to any surrounding code. And in anyway they
affect only these paths that are now broken. That is RAID5 in pnfs
objects-layout code. It does also affect exofs (which was not broken)
but I have tested exofs and it is lower priority then objects-layout
because no one is using exofs, but objects-layout has lots of users."
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
pnfs-obj: Fix __r4w_get_page when offset is beyond i_size
pnfs-obj: don't leak objio_state if ore_write/read fails
ore: Unlock r4w pages in exact reverse order of locking
ore: Remove support of partial IO request (NFS crash)
ore: Fix NFS crash by supporting any unaligned RAID IO
http://lists.infradead.org/pipermail/linux-mtd/2012-May/041408.htmlhttp://lists.infradead.org/pipermail/linux-mtd/2012-June/042422.html
and we finally have the fix. I am quite confident the fix is correct
because I could reproduce the problem with nandsim and verify the
fix. It was also verified by Iwo (the reporter).
I am also confident that this is OK to merge the fix so late because
this patch affects only the fixup functionality, which is not used by
most users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bUPG
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.5-rc8' of git://git.infradead.org/linux-ubifs
Pull UBIFS free space fix-up bugfix from Artem Bityutskiy:
"It's been reported already twice recently:
http://lists.infradead.org/pipermail/linux-mtd/2012-May/041408.htmlhttp://lists.infradead.org/pipermail/linux-mtd/2012-June/042422.html
and we finally have the fix. I am quite confident the fix is correct
because I could reproduce the problem with nandsim and verify the fix.
It was also verified by Iwo (the reporter).
I am also confident that this is OK to merge the fix so late because
this patch affects only the fixup functionality, which is not used by
most users."
* tag 'upstream-3.5-rc8' of git://git.infradead.org/linux-ubifs:
UBIFS: fix a bug in empty space fix-up
We can't guarantee that REQ_DISCARD on dm-mirror zeroes the data even if
the underlying disks support zero on discard. So this patch sets
ti->discard_zeroes_data_unsupported.
For example, if the mirror is in the process of resynchronizing, it may
happen that kcopyd reads a piece of data, then discard is sent on the
same area and then kcopyd writes the piece of data to another leg.
Consequently, the data is not zeroed.
The flag was made available by commit 983c7db347
(dm crypt: always disable discard_zeroes_data).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When process_discard receives a partial discard that doesn't cover a
full block, it sends this discard down to that block. Unfortunately, the
block can be shared and the discard would corrupt the other snapshots
sharing this block.
This patch detects block sharing and ends the discard with success when
sending it to the shared block.
The above change means that if the device supports discard it can't be
guaranteed that a discard request zeroes data. Therefore, we set
ti->discard_zeroes_data_unsupported.
Thin target discard support with this bug arrived in commit
104655fd4d (dm thin: support discards).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a crash when a discard request is sent during mirror
recovery.
Firstly, some background. Generally, the following sequence happens during
mirror synchronization:
- function do_recovery is called
- do_recovery calls dm_rh_recovery_prepare
- dm_rh_recovery_prepare uses a semaphore to limit the number
simultaneously recovered regions (by default the semaphore value is 1,
so only one region at a time is recovered)
- dm_rh_recovery_prepare calls __rh_recovery_prepare,
__rh_recovery_prepare asks the log driver for the next region to
recover. Then, it sets the region state to DM_RH_RECOVERING. If there
are no pending I/Os on this region, the region is added to
quiesced_regions list. If there are pending I/Os, the region is not
added to any list. It is added to the quiesced_regions list later (by
dm_rh_dec function) when all I/Os finish.
- when the region is on quiesced_regions list, there are no I/Os in
flight on this region. The region is popped from the list in
dm_rh_recovery_start function. Then, a kcopyd job is started in the
recover function.
- when the kcopyd job finishes, recovery_complete is called. It calls
dm_rh_recovery_end. dm_rh_recovery_end adds the region to
recovered_regions or failed_recovered_regions list (depending on
whether the copy operation was successful or not).
The above mechanism assumes that if the region is in DM_RH_RECOVERING
state, no new I/Os are started on this region. When I/O is started,
dm_rh_inc_pending is called, which increases reg->pending count. When
I/O is finished, dm_rh_dec is called. It decreases reg->pending count.
If the count is zero and the region was in DM_RH_RECOVERING state,
dm_rh_dec adds it to the quiesced_regions list.
Consequently, if we call dm_rh_inc_pending/dm_rh_dec while the region is
in DM_RH_RECOVERING state, it could be added to quiesced_regions list
multiple times or it could be added to this list when kcopyd is copying
data (it is assumed that the region is not on any list while kcopyd does
its jobs). This results in memory corruption and crash.
There already exist bypasses for REQ_FLUSH requests: REQ_FLUSH requests
do not belong to any region, so they are always added to the sync list
in do_writes. dm_rh_inc_pending does not increase count for REQ_FLUSH
requests. In mirror_end_io, dm_rh_dec is never called for REQ_FLUSH
requests. These bypasses avoid the crash possibility described above.
These bypasses were improperly implemented for REQ_DISCARD when
the mirror target gained discard support in commit
5fc2ffeabb (dm raid1: support discard).
In do_writes, REQ_DISCARD requests is always added to the sync queue and
immediately dispatched (even if the region is in DM_RH_RECOVERING). However,
dm_rh_inc and dm_rh_dec is called for REQ_DISCARD resusts. So it violates the
rule that no I/Os are started on DM_RH_RECOVERING regions, and causes the list
corruption described above.
This patch changes it so that REQ_DISCARD requests follow the same path
as REQ_FLUSH. This avoids the crash.
Reference: https://bugzilla.redhat.com/837607
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
It is very common for the end of the file to be unaligned on
stripe size. But since we know it's beyond file's end then
the XOR should be preformed with all zeros.
Old code used to just read zeros out of the OSD devices, which is a great
waist. But what scares me more about this situation is that, we now have
pages attached to the file's mapping that are beyond i_size. I don't
like the kind of bugs this calls for.
Fix both birds, by returning a global zero_page, if offset is beyond
i_size.
TODO:
Change the API to ->__r4w_get_page() so a NULL can be
returned without being considered as error, since XOR API
treats NULL entries as zero_pages.
[Bug since 3.2. Should apply the same way to all Kernels since]
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
The read-4-write pages are locked in address ascending order.
But where unlocked in a way easiest for coding. Fix that,
locks should be released in opposite order of locking, .i.e
descending address order.
I have not hit this dead-lock. It was found by inspecting the
dbug print-outs. I suspect there is an higher lock at caller that
protects us, but fix it regardless.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Do to OOM situations the ore might fail to allocate all resources
needed for IO of the full request. If some progress was possible
it would proceed with a partial/short request, for the sake of
forward progress.
Since this crashes NFS-core and exofs is just fine without it just
remove this contraption, and fail.
TODO:
Support real forward progress with some reserved allocations
of resources, such as mem pools and/or bio_sets
[Bug since 3.2 Kernel]
CC: Stable Tree <stable@kernel.org>
CC: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
In RAID_5/6 We used to not permit an IO that it's end
byte is not stripe_size aligned and spans more than one stripe.
.i.e the caller must check if after submission the actual
transferred bytes is shorter, and would need to resubmit
a new IO with the remainder.
Exofs supports this, and NFS was supposed to support this
as well with it's short write mechanism. But late testing has
exposed a CRASH when this is used with none-RPC layout-drivers.
The change at NFS is deep and risky, in it's place the fix
at ORE to lift the limitation is actually clean and simple.
So here it is below.
The principal here is that in the case of unaligned IO on
both ends, beginning and end, we will send two read requests
one like old code, before the calculation of the first stripe,
and also a new site, before the calculation of the last stripe.
If any "boundary" is aligned or the complete IO is within a single
stripe. we do a single read like before.
The code is clean and simple by splitting the old _read_4_write
into 3 even parts:
1._read_4_write_first_stripe
2. _read_4_write_last_stripe
3. _read_4_write_execute
And calling 1+3 at the same place as before. 2+3 before last
stripe, and in the case of all in a single stripe then 1+2+3
is preformed additively.
Why did I not think of it before. Well I had a strike of
genius because I have stared at this code for 2 years, and did
not find this simple solution, til today. Not that I did not try.
This solution is much better for NFS than the previous supposedly
solution because the short write was dealt with out-of-band after
IO_done, which would cause for a seeky IO pattern where as in here
we execute in order. At both solutions we do 2 separate reads, only
here we do it within a single IO request. (And actually combine two
writes into a single submission)
NFS/exofs code need not change since the ORE API communicates the new
shorter length on return, what will happen is that this case would not
occur anymore.
hurray!!
[Stable this is an NFS bug since 3.2 Kernel should apply cleanly]
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
UBIFS has a feature called "empty space fix-up" which is a quirk to work-around
limitations of dumb flasher programs. Namely, of those flashers that are unable
to skip NAND pages full of 0xFFs while flashing, resulting in empty space at
the end of half-filled eraseblocks to be unusable for UBIFS. This feature is
relatively new (introduced in v3.0).
The fix-up routine (fixup_free_space()) is executed only once at the very first
mount if the superblock has the 'space_fixup' flag set (can be done with -F
option of mkfs.ubifs). It basically reads all the UBIFS data and metadata and
writes it back to the same LEB. The routine assumes the image is pristine and
does not have anything in the journal.
There was a bug in 'fixup_free_space()' where it fixed up the log incorrectly.
All but one LEB of the log of a pristine file-system are empty. And one
contains just a commit start node. And 'fixup_free_space()' just unmapped this
LEB, which resulted in wiping the commit start node. As a result, some users
were unable to mount the file-system next time with the following symptom:
UBIFS error (pid 1): replay_log_leb: first log node at LEB 3:0 is not CS node
UBIFS error (pid 1): replay_log_leb: log error detected while replaying the log at LEB 3:0
The root-cause of this bug was that 'fixup_free_space()' wrongly assumed
that the beginning of empty space in the log head (c->lhead_offs) was known
on mount. However, it is not the case - it was always 0. UBIFS does not store
in it the master node and finds out by scanning the log on every mount.
The fix is simple - just pass commit start node size instead of 0 to
'fixup_leb()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Cc: stable@vger.kernel.org [v3.0+]
Reported-by: Iwo Mergler <Iwo.Mergler@netcommwireless.com>
Tested-by: Iwo Mergler <Iwo.Mergler@netcommwireless.com>
Reported-by: James Nute <newten82@gmail.com>
Pull last minute Ceph fixes from Sage Weil:
"The important one fixes a bug in the socket failure handling behavior
that was turned up in some recent failure injection testing. The
other two are minor bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: endian bug in rbd_req_cb()
rbd: Fix ceph_snap_context size calculation
libceph: fix messenger retry
One of the bugs was introduced in 3.5-rc1. Others have
been there for longer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=zpJG
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull three md bugfixes from NeilBrown:
"One of the bugs was introduced in 3.5-rc1. Others have been there for
longer."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid1: close some possible races on write errors during resync
md: avoid crash when stopping md array races with closing other open fds.
md: fix bug in handling of new_data_offset
Pull networking changes from David Miller:
"Ok, we should be good to go now"
1) We have to statically initialize the init_net device list head rather
than do so in an initcall, otherwise netprio_cgroup crashes if it's
built statically rather than modular (Mark D. Rustad)
2) Fix SKB null oopser in CIPSO ipv4 option processing (Paul Moore)
3) Qlogic maintainers update (Anirban Chakraborty)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Statically initialize init_net.dev_base_head
MAINTAINERS: Changes in qlcnic and qlge maintainers list
cipso: don't follow a NULL pointer when setsockopt() is called
Pull HID update from Jiri Kosina:
"A final round of changes for HID for 3.5: just device ID additions."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for Zytronic panels
HID: add Sennheiser BTD500USB device support
HID: add battery quirk for Apple Wireless ANSI
The strcpy was being used to set the name of the board. Since the
destination char* was read-only and the name is set statically at
compile time; this was both wrong and redundant.
The type of char* is changed to const char* to prevent future errors.
Reported-by: Radek Masin <radek@masin.eu>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
[ Taking directly due to vacations - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixups are executed once the pci-device is found which is during boot
process so __init seems fine as long as the platform does not support
hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
[ralf@linux-mips.org: Made piixirqmap[] in malta_piix_func0_fixup()
__initdata.]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit: 3777808873 [bug.h: need linux/kernel.h
for TAINT_WARN.] breaks all MIPS builds.
CC arch/mips/kernel/machine_kexec.o
In file included from include/linux/kernel.h:20:0,
from include/asm-generic/bug.h:35,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bug.h:41,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:20,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/log2.h: In function '__ilog2_u32':
include/linux/log2.h:34:2: error: implicit declaration of function 'fls' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__ilog2_u64':
include/linux/log2.h:42:2: error: implicit declaration of function 'fls64' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__roundup_pow_of_two':
include/linux/log2.h:63:2: error: implicit declaration of function 'fls_long' [-Werror=implicit-function-declaration]
In file included from include/linux/bitops.h:22:0,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h: At top level:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:615:19: error: static declaration of 'fls' follows non-static declaration
include/linux/log2.h:34:9: note: previous implicit declaration of 'fls' was here
In file included from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:651:0,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/asm-generic/bitops/fls64.h:18:28: error: static declaration of 'fls64' follows non-static declaration
include/linux/log2.h:42:9: note: previous implicit declaration of 'fls64' was here
In file included from include/linux/signal.h:38:0,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/bitops.h:160:24: error: conflicting types for 'fls_long'
include/linux/log2.h:63:16: note: previous implicit declaration of 'fls_long' was here
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/kernel/machine_kexec.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: yuasa@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Linuxppc-dev <linuxppc-dev@ozlabs.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Cc: Linux-sh list <linux-sh@vger.kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Patchwork: https://patchwork.linux-mips.org/patch/4000/
Tested-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since we have delayed irq enabling to ->smp_finish()
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just to catch a potential issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3852/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To prevent a problem as commit 5fbd036b [sched: Cleanup cpu_active madness]
and commit 2baab4e9 [sched: Fix select_fallback_rq() vs cpu_active/cpu_online]
try to resolve, move set_cpu_online() to the brought up CPU and with irq
disabled.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3851/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have move irq enable to ->smp_finish. Place ->smp_finish() a little
late to prepare for move set_cpu_online() into start_secondary.
And it's not necessary to call cpu_set(cpu, cpu_callin_map) and
synchronise_count_slave() with irq enabled.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3850/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To prepare for smoothing set_cpu_[active|online]() mess up
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Daney <david.daney@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building oprofile as a module for R10000 or R7000 class processors,
E9000 or MIPSxx class cores since 3572a2c37f
[MIPS: make oprofile use cp0_perfcount_irq if it is set] an
ERROR: "cp0_compare_irq" [arch/mips/oprofile/oprofile.ko] undefined!
error will happen. Fixed by exporting cp0_compare_irq.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cc1: warnings being treated as errors
arch/mips/kernel/perf_event_mipsxx.c:166: error: 'counters_per_cpu_to_total' defined but not used
make[2]: *** [arch/mips/kernel/perf_event_mipsxx.o] Error 1
make[2]: *** Waiting for unfinished jobs....
It was first introduced by 82091564cf [MIPS:
perf: Add support for 64-bit perf counters.] in 3.2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: david.daney@cavium.com
Patchwork: https://patchwork.linux-mips.org/patch/3357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
show_backtrace() was passed a NULL pointer which caused paging
request fail. Set to current task as other architectures (ARM,
etc) do when passed a NULL task pointer.
Signed-off-by: Vincent Wen <vincentwenlinux@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3524/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel@pengutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/3565/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following build breakage in v3.4-rc1:
CC kernel/irq_work.o
In file included from include/linux/irq_work.h:4:0,
from kernel/irq_work.c:10:
include/linux/llist.h: In function 'llist_del_all':
include/linux/llist.h:178:2: error: implicit declaration of function 'BUILD_BUG_ON' [-Werror=implicit-function-declaration]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3568/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
